Shenzhen led color opto electronic Co.
,Ltd
WS2813
1 / 11
Addressable LED Manufacturer
Web:www.szledcolor.com, Email:admin@szlcoe.com
Tel :+86-0755-27350605 Fax : +86-0755-23245913
WS2813
LED COLOR
Intelligent control LED
integrated light source
Features and Benefits
The control circuit and the LED share the only power source.
The control circuit and RGB chip are integrated in a 5050 components, to form an external control pixel.
Using the built-in signal reshaping circuit to achieve the signal waveform shaping, and no distortion of waveform of
signal takes place.
Built-in power-on reset and brown-out reset circuits.
The gray levels of each pixel are of 256 levels, which achieves 256*256*256=16777216 full-color display, and
the refresh frequency reaches to 2KHz/s.
Serial cascade interface, data receiving and decoding depend on just one signal line.
Dual-signal wires version, signal break-point continuous transmission.
Any two point the distance more than 3m transmission signal without any increase circuit.
When the refresh rate is 30fps, cascade numbers are far more than 1024 points.
Data transmitting at speeds of up to 800Kbps.
Good color consistency reliability, high cost-effective.
Applications
Guardrail tube series, point light display series, flexible/rigid strips series, module series applications.
Lighting stage costumes, innovative gadgets or any other electronic products.
General description
WS2813 is an intelligent control LED light source that the control circuit and RGB chip are integrated in a package
of 5050 components. Its internal include intelligent digital port data latch and signal reshaping amplification drive circuit.
Also include a precision internal oscillator and a 12V voltage programmable constant current control part,
which achieves highly consistent color effect.
The data transfer protocol use single NZR communication mode. After the pixel power-on reset, the DIN port receive
data from controller, the first pixel collect initial 24bit data then sent to the internal data latch, the other data which
reshaping by the internal signal reshaping amplification circuit sent to the next cascade pixel through the DO port. After
transmission for each pixel, the signal to reduce 24bit. Every pixel adopts auto-reshaping transmit technology, making
the pixel cascade numbers are not limited to the signal transmission, only relate to the speed of signal transmission.
The BIN receives the data signal, and then compare the data with the DIN side after phagocytosis of 24bit data, if DIN
do NOT receive the signal, then switching to BIN for receiving the input signal, which ensure that any the IC's damage
does not affect the signal cascade transmission and make the BIN in state of receiving signal until restart after power-off.
Refresh Frequency updates to 2KHz, Low Frame Frequency and no Flicker appear in HD Video Camera.
250us or more of reset time, it wont cause wrong reset while interruption, it supports the lower frequency and
inexpensive MCU.
Therere in a choice of 18mA or 5mA current version, and also in a choice of high brightness or cost-effective version.
That is to say, WS2813 is provided with four versions.
2 / 11
www.szledcolor.com
WS2813
LED COLOR
Intelligent control LED
integrated light source
Mechanical Dimensions
Remarks
1. Dimension=5.0*5.4*1.5mm 2. Default tolerance=0.01mm
PIN Configuration
PIN Function
NO.
Symbol
PIN
Function description
NC
HANGING
Suspended in PCB layout, the circuit will be
out of operation when it connects to other circuits.
VDD
POWER VOLTAGE
Power Voltage, connect to +5V
DO
DATA OUT
Control data signal output
DIN
DATA IN
Control data signal input
GND
GROUND
Data & Power Grounding
BIN
BACKUP DATA IN
Backup Control data signal input
3 / 11
www.szledcolor.com
WS2813
LED COLOR
Intelligent control LED
integrated light source
Absolute Maximum Ratings
Parameter
Symbol
Ratings
Unit
Power supply voltage
VDD
+3.5~+5.3
Input voltage
VI
-0.5VDD+0.5
Operating Temperature
Topt
-25+60
Storage Temperature
Tstg
-40~+120
Electrical Characteristics (TA=-20+70, VDD=4.55.5V, VSS=0V)
Parameter
Symbol
Min.
Tpy.
Max.
Unit
Conditions
Input Current
II
VI=VDD/VSS
High-level Input
VIH
0.7VDD
DIN, SET
Low-level Input
VIL
0.3 VDD
DIN, SET
Hysteresis voltage
VH
0.35
DIN, SET
Switching Characteristics (TA=-20+70, VDD=4.55.5V, VSS=0V)
Parameter
Symbol
Condition
Min
Tpy
Max
Unit
Transmission Delay Time
tPLZ
CL=15pF, DINDOUT, RL=10K
300
ns
Fall time
tTHZ
120
Input-capacitance
CI
15
pF
CL=300pF, OUTR/OUTG/OUTB
4 / 11
www.szledcolor.com
WS2813
LED COLOR
Intelligent control LED
integrated light source
LED Characteristics
WS2813A
WS2813B
WS2813C
WS2813D
Quiescent Current
0.6mA
0.6mA
0.2mA
0.2mA
RGB Channel Constant Current
18mA
18mA
5mA
5mA
480mcd
360mcd
120mcd
100mcd
1500 mcd
1150 mcd
540 mcd
420mcd
Brightness-BLUE (Centering)
320mcd
220mcd
130mcd
110mcd
Brightness-WHITE (Centering)
2300mcd
1710mcd
790mcd
630mcd
Wavelength-RED
620-622nm
620-622nm
620-622nm
620-622nm
Wavelength-GREEN
522-525nm
522-525nm
522-525nm
522-525nm
Wavelength-BLUE
467-470nm
467-470nm
467-470nm
467-470nm
Brightness-RED (Centering)
Brightness-GREEN (Centering)
Data Transfer Time (TH+TL=1.25s300ns)
T0H
0-code, High-level time
300ns~450ns
T1H
1-code, High-level time
750ns~1000ns
T0L
0-code, Low-level time
300ns~100us
T1L
1-code, Low-level time
300ns~100us
RES
Frame unit, Low-level time
300s or more
5 / 11
www.szledcolor.com
WS2813
LED COLOR
Intelligent control LED
integrated light source
Data Transmission Method
Note: D1 is the data from MCU, and D2, D3, D4 are from Cascade Circuits.
Composition of 24bit data
R7
R6
R5
R4
R3
R2
R1
R0
G7
G6
G5
G4
G3
G2
G1
G0
B7
B6
B5
B4
B3
B2
B1
B0
Note: Data transmit in order of GRB, high bit data is first.
6 / 11
www.szledcolor.com
WS2813
LED COLOR
Intelligent control LED
integrated light source
Reflow Instructions
1) Lead-free Reflow:
2) Leaded Reflow:
7 / 11
www.szledcolor.com
WS2813
LED COLOR
Intelligent control LED
integrated light source
Curve Description
Lead Reflow
Solder
Lead-free Reflow
Solder/SMT
The lowest preheat temperature (Tsmin)
100
150
The highest preheat temperature (Tsmax)
150
200
Preheating time (Tsmin to Tsmax) (ts)
60-120 S
60-180 S
Average rate of temperature rise (Tsmax to Tp)
<3/S
<3/S
LIQUID REGION temperature (TL)
183
217
LIQUID REGION Holding Time (tL)
60-150 S
60-150 S
Peak Temperature (Tp)
215
245
High Temperature Region(Tp=-5) Holding Time (tp)
<10 S
<10 S
Cooling Rate
<6/S
<6/S
Room Temperature to Peak Holding Time
<6 min
<6 min
Remarks
1.
2.
This has to be baked for 48 hours at the baking temperature of 65-70 before being used.
Use up with 2 hours after taking out from oven.
3.
Please replace the unused LEDs into oven.
Reflow instruction
1. No more than two times of reflow.
2. Do not beat the colloid surface when the material is heated.
Manual Soldering instruction
1. Soldering irons temperature must be under 300, and operating time must be less than 3 seconds.
2. It should be done only once for the manual soldering.
8 / 11
www.szledcolor.com
WS2813
LED COLOR
Intelligent control LED
integrated light source
Repairing instruction
Normally, it cant be repaired after reflow. You need to use double-ended solder iron and make sure that whether it will
do damage to the LEDs characteristics when repairing is inevitable.
Storing and Transporting
1Scope of application
Front side up, moisture-proof and waterproof, no extrusion, no collision and no vibration.
2Storage and its period
1 Room temperature sealed storage: 2030, 40%60%RH, product is valid for ONE month.
2 Moisture-proof sealed storage: 2030, 25%60%RH, product is valid for THREE month.
3 Use up with 2 hours after removing from packages.(Environmental conditions for temperature <30,
relative humidity<60%)
Dehumidification
We would recommend to do dehumidification if they exceed the valid storage period of products or dampened due to
other reasons.
Dehumidification Method: 70-75/222 Hours
Electrostatic Protection
LED is an electrostatic sensitive component, although the LED products are with excellent anti-static ability, they will
cause a certain damage by any electrostatic discharge. By taking some electrostatic measures to avoid the damages when
using the LEDs, such as wearing anti-static gloves and anti-static bracelet, etc..
Precautions
Pressing the colloid surface will affect the reliability of LED because the LED is advanced silicone-gel. And therefore
precautions should be taken to avoid the strong pressure on the component. Its proper to make the LED be used in safe
condition when using a suction nozzle. Silicon packing with soft and elastic, it greatly reduces thermal stresses and
unable to bear external mechanical forces. Therefore, preventive measures should be taken in process of manually
handling.
9 / 11
www.szledcolor.com
WS2813
LED COLOR
Intelligent control LED
integrated light source
Clip the LED from its side.
Neither directly touch the gel surface with the hand or sharp instrument, it may damage its internal circuit.
Not to be double stacked, it may damage its internal circuit.
Can not be stored in or applied in the acidic sites of PH<7.
Label
P/N:
Packing:
Quantity:
Date:
10 / 11
www.szledcolor.com
WS2813
LED COLOR
Intelligent control LED
integrated light source
Carrier tape (Unit: mm)
Reel size (Unit: mm)
Moisture-proof bag
11 / 11
www.szledcolor.com
