WC5

PARTS FABRICATION
AUTHOR: J. RANDLE

2005 Randle Design, LLC

All rights reserved

This section contains a complete list of the hardware and fabricated parts required to assemble clock WC5,
plus drawings of the individual parts. Also included is a list of suggested sources for all materials.
Clock WC5 was designed to be fabricated with as few shop tools as possible. Excluding the wall shelf, the
prototype for this clock was built with the following tools:
o A basic scroll saw with fine tooth blades and an assortment of scroll sanders.
o A drill press with a set of basic twist drills and a set of Forsner bits.
o A small belt/disc sander with 400 grit sanding medium.
o A turning lathe (useful for grooving rope pulleys but not absolutely necessary)
The wall shelf was designed to be fabricated with the tools available in the shop where the prototype was built.
Its design can be altered by the builder to use whatever tools are available.
Some of the drawings in this section contain all of the dimensions necessary to lay out the subject part. Others,
such as the wheel drawings, contain only basic dimensions. It is intended that the under-dimensioned parts be
fabricated using cutting patterns as laying them out accurately would be very difficult. Where noted the
drawings can be used as cutting patterns if they are printed to scale.
Listed below are notes and suggestions pertaining to the fabrication of some of the parts:
ARBOR SHAFTS The wooden arbor shafts are all designed to be made from good quality dowel stock.
Centering the holes in the ends of the shafts is important. A lathe with a headstock chuck and a tailstock drill
chuck would be handy here. Otherwise, you can make a clamp block similar to the one shown below.
Carefully align the hole in the block with your drill press chuck, clamp the block in place, and use it as a holder
for drilling the shaft end holes.

Typical Shaft Clamp Block

PINS The pins are all cut from brass rod. 360 H02 brass is soft and can be easily cut with a hacksaw then finish
sanded to length on a disc sander. Drilling a hole to a known depth in the end of a wooden dowel rod then
using the rod as a holder for sanding the short pins works well and saves fingers. The ends of the pins can be
chamfered while in the holder by holding them against a running sanding belt and spinning them between
your fingers. The actual size and angle of the chamfer isnt critical. A typical holder with pin inserted is shown
here. A holder will be needed for each pin diameter.

Typical Pin Holder w/Pin

ROPE SHEAVES All of the rope sheaves are designed to be sawn from single pieces of 12mm (15/32) thick
baltic birch plywood and grooved on a lathe faceplate. If no lathe is available the sheaves can be made by
cutting three pieces of 3mm (1/8) thick plywood to the proper diameter then gluing them together. The
grooves wont be tapered but the pulleys should work okay. Of course they will be only 9mm thick making it
necessary to shim them with washers at assembly.

2
DIAL A simple way to make the dial shown is:
1.

Apply the full size adhesive backed pattern sections to plywood stock making sure the sections line up
properly at the pattern match lines.

2.

Use an xacto knife to carefully cut away the pattern at the numbers and minute marks. Be careful to
not cut into the plywood.

3.

Spray the cut out pattern with a good wood sealer. This is important to keep the number paint from
soaking into the plywood causing the edges of the numbers to be blurred.

4.

Spray the numbers with a good gloss paint of your color choice. Several thin coats will be necessary
to hide the wood grain.

5.

Cut out the dial and sand the cut edges.

6.

Drill and countersink the screw holes. The screw centers are marked on the pattern.

7.

Remove the pattern and clean up any rough edges.

8.

Finish by spraying the entire dial with a good wood sealer.

FRAME POSTS The holes in these posts are to be drilled and tapped with the same taps used for tapping screw
holes in metal. Tapping holes in hardwood will provide a strong connection as long as you use coarse thread
taps. The necessary tap drills and taps can be bought at a number of places including your local building
supply.
PENDULUM SUPPORT BRIDGE The upper end of the pendulum suspension spring (pin end) must fit snugly into the
slots in this part but not so snug that the spring cant rotate on its pin. Fit of this part should be checked and
adjusted as necessary during fabrication.
WHEELS If you look at the drawings closely you will note that the gear teeth on the wheels in the time train of
this clock (winding drum to escapement) have an epicycloidal profile on one face and are straight on the
other face. The epicycloidal (front) face is the working face and must be cut accurately. The back face does
not touch anything and is simply cut away for clearance. Cutting away the unused back face makes the
teeth simpler to cut and provides more clearance to compensate for small errors in tooth layout. Because of
the difference in the profile of the front and back faces, the gear teeth must be oriented as shown if the clock
is to run properly.
The wheels not in the time train i.e. WHEEL T-HR, WHEEL T-INT & WHEEL T-6 have epicycloidal faces on both sides
of their teeth. The reason is that these wheels run slack (no load), and backlash here will cause the hour hand
and second hand to be loose.
All of the wheels are drawn as single parts but are actually composites of several pieces of plywood glued
together. The recommended procedure for making WHEEL T-1 is:
1.

Apply the furnished wheel pattern to a piece of plywood of the proper thickness.

2.

Drill the center hole with a Forsner bit. A Forsner bit creates a cleaner hole than a twist drill would
create. The hole center is clearly marked on the pattern.

3.

Cut out the gear blank along its outside diameter. Do not try to cut the teeth yet.

4.

Center punch the remaining holes marked on the pattern.

5.

Use an xacto knife to carefully cut away the pattern along the profile of each gear tooth. This step
may look useless, but if it is skipped all of the drilling, sawing, and sanding around the teeth will cause
the pattern to come loose making it difficult to properly finish the part.

6.

Carefully drill a hole at the root of each tooth. You will have to use a twist drill here because Forsner
bits that small arent available. Accurate location is important here.

3
7.

Drill the five pin holes at the location shown.

8.

Use a scroll saw to rough cut the profile of the teeth.

9.

Use scroll sanders to shape the teeth to the pattern. Dont quit sanding too soon. Clearance
between the gear teeth and the pinion pins is critical.

10. When finished with the teeth, use an xacto knife to carefully make a cut through the pattern around
the outside circle shown on the pattern.
11. Remove the pattern inside the cut.
12. Lay the wheel aside and cut a ring from another piece of plywood. The ring dimensions are shown on
the drawing.
13. Glue the ring to the wheel using the outer portion of the pattern as a guide.
14. Remove the rest of the pattern.
15. Saw out circular pieces of plywood which can be stacked together to provide a thickness equal to
the length of the wheel hub. The diameter of the pieces should be slightly larger than the diameter of
the hub.
16. With a Forsner bit drill a hole in the center of each circular piece. The hole should be the same
diameter as the hole in the center of the wheel.
17. Sand the pieces to the finished diameter of the wheel hub. This can easily be done on a belt/disc
sander by making a jig as shown here; inserting the disc on the jig pin and slowly rotating it as the
sander cuts it to size.

18. Glue the hub pieces to the wheel. An excellent way to do this is to drill a hole the same size as the
wheel center hole in one jaw of a wooden parallel clamp; insert a piece of dowel rod into the hole
from the back; stack the parts to be glued on the rod; close the parallel clamp; and then remove the
dowel rod. A typical gluing setup is shown here:

Typical Wheel Gluing Setup

19. When the glue is dry, remove the wheel from the clamp, clean up any drips, and spray the entire
wheel with a coat of wood sealer.
20. When the sealer is dry, lightly sand the working faces of the gear teeth to remove the wood sealer
from them. A clock will not run if sealer or any other finish is allowed to build up on its gear teeth.
ANCHOR The shape of the pallets (the tips of the anchor) is arguably the most important feature in the clock.
The pallet angles affect the amount of force applied to the pendulum to keep it swinging. Be especially
careful to cut them to the proper angle and sand them smooth. Only round the tips enough to remove any
burrs. Do not leave any wood sealer on the pallet faces. In fact, putting a single drop of good quality clock oil
on each pallet face and allowing it to soak into the wood is a good idea.
PENDULUM BOB SHELL The shell of the pendulum bob was designed to be cut as two pieces for convenience.
You can glue both patterns to the same piece of wood and cut it as a single piece if you like.
PENDULUM BOB SHELL COVERS It is a good idea to cut both shell covers slightly oversize, then sand them to fit
the shell after the pendulum bob is assembled.
WEIGHT SHELL TOPS The tops of the weight shells were designed as a composite of several pieces. Since
thicknesses of plywood can vary slightly, it is a good idea to cut the outside pieces of the composite a bit wider
than shown. This will allow you to trim the assembled part to the correct width after gluing. When trimming, be
sure to keep the part symmetrical about its center line.
Since the top of the small weight shell is made up of only three pieces, and since the gap between the outer
pieces needs to be held to the dimension shown, its overall width may vary slightly. You may need to adjust the
width of the shell front and back panels and the width of the shell bottom slightly to compensate.
WEIGHT SHELL FRONT & BACK PANELS It is a good idea to cut the weight shell front and back panels slightly
wider than shown, then to sand them to fit the side panels after gluing.
Fabrication of the parts not mentioned above should be obvious from studying the drawings and the notes and
suggestions above. If you have questions about any of them feel free to contact the designer at
woodclocks@charter.net for answers.

WC5 CONSOLIDATED PARTS LIST

ITEM

PART NO.

DESCRIPTION

MATERIAL

QTY.

SOURCE

BLOCK

1/2" W X 3/4" H X 2 5/32" LG

OAK

FABRICATE

CURVED DISC SPRING

MC # 9716K52

301 STAINLESS STEEL

MCMASTER-CARR

DOWEL PIN

0.0625 DIA X 1/2" LG

BRASS

LOCAL HDWR

FLANGED BEARING

MC # 6294K86, 3/16" ID x 5/16" OD x 1/4" LG

MDS-FILLED NYLON

20

MCMASTER-CARR

FLANGED BEARING

MC # 6294K89, 3/8" ID X 1/2" OD X 3/8" LG

MDS-FILLED NYLON

MCMASTER-CARR

FLAT WASHER, SMALL OD

#10 NOM

BRASS

15

LOCAL HDWR

FLAT WASHER, SMALL OD

3/8 NOM

BRASS

LOCAL HDWR

FLAT WASHER, SMALL OD

#4 NOM

BRASS

LOCAL HDWR

LEAD FILL

MC # 9030K34

#8 LEAD SHOT (9 LBS)

MCMASTER-CARR

10

MACHINE SCREW HEX NUT

#8-32UNC

BRASS

LOCAL HDWR

11

MACHINE SCREW HEX NUT

#4-40 UNC

BRASS

LOCAL HDWR

12

OVAL HD MACHINE SCREW

#8-32 UNC x 1 1/8" LG

BRASS

LOCAL HDWR

13

PENDULUM ROD

1/2" DIA X 31" LG

OAK

FABRICATE

14

PLUG

3/4" DIA [COMPRESSED] x 1/2" LG

CORK

15

ROPE

1/8" DIA X 10'-6" LG (BRAIDED)

NYLON

LOCAL HDWR

16

ROUND HD MACHINE SCREW

#10-24 UNC x 1" LG

BRASS

LOCAL HDWR

17

ROUND HD MACHINE SCREW

#4-40 UNC x 5/8" LG

BRASS

LOCAL HDWR

18

SPLIT PIN

M2 x 12 MM LG

BRASS

LOCAL HDWR

19

SPLIT PIN

M2 x 22 MM LG

BRASS

LOCAL HDWR

20

SPRING PIN (SLOTTED)

5/64 DIA X 3/4" LG

STAINLESS STEEL

MCMASTER-CARR

21

SPRING PIN (SLOTTED)

5/64" DIA X 3/8" LG

STAINLESS STEEL

MCMASTER-CARR

22

SUSPENSION SPRING

NORKRO # SS-41

NORKRO

23

THREADED ROD

#10-24UNC X 1 3/4" LG

STEEL

LOCAL HDWR

24

THUMB NUT

#10-32UNF

BRASS

LOCAL HDWR

25

WC5-00-01

SHAFT

OAK

FABRICATE

26

WC5-00-02-A

PIN

360 H02 BRASS

FABRICATE

27

WC5-00-02-B

PIN

360 H02 BRASS

12

FABRICATE

28

WC5-00-02-C

PIN

360 H02 BRASS

FABRICATE

29

WC5-00-02-D

PIN

360 H02 BRASS

FABRICATE

30

WC5-00-02-E

PIN

360 H02 BRASS

18

FABRICATE

31

WC5-00-02-F

PIN

360 H02 BRASS

11

FABRICATE

32

WC5-00-02-G

PIN

360 H02 BRASS

12

FABRICATE

33

WC5-00-02-H

PIN

360 H02 BRASS

FABRICATE

34

WC5-00-02-J

PIN

360 H02 BRASS

20

FABRICATE

35

WC5-00-02-K

PIN

360 H02 BRASS

FABRICATE

36

WC5-00-02-L

PIN

360 H02 BRASS

15

FABRICATE

37

WC5-00-03

ROPE SHEAVE

BALTIC BIRCH PLYWOOD

FABRICATE

38

WC5-00-04

SHAFT

360 H02 BRASS

FABRICATE

39

WC5-01-01

SHELF

OAK

FABRICATE

40

WC5-01-02

BACK PLATE

OAK

FABRICATE

41

WC5-01-03

BRACE

OAK

FABRICATE

42

WC5-02-01

FRAME PLATE, REAR

BALTIC BIRCH PLYWOOD

FABRICATE

43

WC5-02-02

FRAME PLATE, MIDDLE

BALTIC BIRCH PLYWOOD

FABRICATE

44

WC5-02-03

FRAME PLATE, FRONT

BALTIC BIRCH PLYWOOD

FABRICATE

45

WC5-02-04

DIAL

BALTIC BIRCH PLYWOOD

FABRICATE

46

WC5-02-05

FRAME POST

OAK

FABRICATE

47

WC5-02-06

DIAL POST

OAK

FABRICATE

48

WC5-02-07

PENDULUM SUPPORT BRIDGE

BALTIC BIRCH PLYWOOD

FABRICATE

49

WC5-02-08

PIN

360 H02 BRASS

FABRICATE

50

WC5-03-01

WHEEL

BALTIC BIRCH PLYWOOD

FABRICATE

51

WC5-03-02

PIVOT

360 H02 BRASS

FABRICATE

52

WC5-03-03-01

CLICK

BALTIC BIRCH PLYWOOD

FABRICATE

WC5 CONSOLIDATED PARTS LIST

ITEM

PART NO.

DESCRIPTION

MATERIAL

QTY.

SOURCE

53

WC5-03-04

ROPE PULLEY

BALTIC BIRCH PLYWOOD

FABRICATE

54

WC5-03-05

ROPE PIN

STAINLESS STEEL

FABRICATE

55

WC5-04-01

SHAFT

OAK

FABRICATE

56

WC5-04-02

PIVOT (BACK)

360 H02 BRASS

FABRICATE

57

WC5-04-03

WHEEL

BALTIC BIRCH PLYWOOD

FABRICATE

58

WC5-05-01

PIVOT (FRONT)

360 H02 BRASS

FABRICATE

59

WC5-05-02

DISC

BALTIC BIRCH PLYWOOD

FABRICATE

60

WC5-05-03

WHEEL

BALTIC BIRCH PLYWOOD

FABRICATE

61

WC5-05-04

HAND (MINUTE)

BALTIC BIRCH PLYWOOD

FABRICATE

62

WC5-05-05

HAND (HOUR)

BALTIC BIRCH PLYWOOD

FABRICATE

63

WC5-06-01

DISC

BALTIC BIRCH PLYWOOD

FABRICATE

64

WC5-06-02

WHEEL

BALTIC BIRCH PLYWOOD

FABRICATE

65

WC5-07-01

WHEEL

BALTIC BIRCH PLYWOOD

FABRICATE

66

WC5-08-01

ESCAPE WHEEL

BALTIC BIRCH PLYWOOD

FABRICATE

67

WC5-09-01

PIVOT

360 H02 BRASS

FABRICATE

68

WC5-09-02

WHEEL

BALTIC BIRCH PLYWOOD

FABRICATE

69

WC5-09-03

SECOND DISC

BALTIC BIRCH PLYWOOD

FABRICATE

70

WC5-10-01

PIVOT

360 H02 BRASS

FABRICATE

71

WC5-10-02

WHEEL

BALTIC BIRCH PLYWOOD

FABRICATE

72

WC5-11-01

ANCHOR

BALTIC BIRCH PLYWOOD

FABRICATE

73

WC5-11-02

IMPULSE LEVER

BALTIC BIRCH PLYWOOD

FABRICATE

74

WC5-12-01

LEADER

BALTIC BIRCH PLYWOOD

FABRICATE

75

WC5-12-02

BOB GUIDE

OAK

FABRICATE

76

WC5-12-03

ADJUSTING ROD

360 H02 BRASS

FABRICATE

77

WC5-12-04-01

SHELL HALF

BALTIC BIRCH PLYWOOD

FABRICATE

78

WC5-12-04-02

SHELL COVER

BALTIC BIRCH PLYWOOD

FABRICATE

79

WC5-13-01

SHELL TOP

BALTIC BIRCH PLYWOOD

FABRICATE

80

WC5-13-02-A

FRONT/BACK PANEL

BALTIC BIRCH PLYWOOD

FABRICATE

81

WC5-13-02-B

SIDE PANEL

BALTIC BIRCH PLYWOOD

FABRICATE

82

WC5-13-03

SHELL BOTTOM

BALTIC BIRCH PLYWOOD

FABRICATE

83

WC5-14-01

SHELL TOP

BALTIC BIRCH PLYWOOD

FABRICATE

84

WC5-14-02-A

FRONT/BACK PANEL

BALTIC BIRCH PLYWOOD

FABRICATE

85

WC5-14-02-B

SIDE PANEL

BALTIC BIRCH PLYWOOD

FABRICATE

86

WC5-14-03

SHELL BOTTOM

BALTIC BIRCH PLYWOOD

FABRICATE

SUGGESTED MATERIAL SOURCES

MATERIAL

VENDOR WEB ADDRESS

VENDOR

Baltic Birch Plywood

Sloan's Woodshop

http://www.sloanswoodshop.com/

Oak Dowel Rod

Local Building Supply

-------

Brass Rod

OnlineMetals.com

http://www.onlinemetals.com/

Clock Parts

Norkro Clock Company, Inc.

http://www.norkro.com/

Miscellaneous Hardware

McMaster-Carr

http://www.mcmaster.com/

Miscellanous Fasteners

Local Hardware Supply

-------

2 1/32"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1

3/8"

2X

3/16"

1/2"

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

PROPRIETARY AND CONFIDENTIAL

The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

1"

Third angle projection.

SHAFT
WOOD CLOCK WC5

Drawing No:

1"

1/32" x 45

SECTION A-A

WC5-00-01

Sheet 1 of 1

No. Required: 4

Material: OAK
"B"

"A"

"C" TYP

ITEM

"A"

"B"

"C"

# REQD

WC5-00-02-A

3/16

1 7/16

1/64

W C5-00-02-B

3/16

15/16

1/64

12

WC5-00-02-C

3/16

13/16

1/64

WC5-00-02-D

1/8

1/64

W C5-00-02-E

1/8

3/4

1/64

18

W C5-00-02-F

1/8

11/16

1/64

11

WC5-00-02-G

1/8

41/64

1/64

12

W C5-00-02-H

1/8

17/32

1/64

W C5-00-02-J

1/8

15/32

1/64

20

W C5-00-02-K

3/32

3/4

1/64

W C5-00-02-L

3/32

17/32

1/64

15

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

PIN
WOOD CLOCK WC5
WC5-00-02

Material: 360 H02 BRASS

Sheet 1 of 1

No. Required: SEE TABLE

12
15/32"
15

A
1 7/8"

R1/16"
1 3/8"

3/8"

A
SECTION A-A
Drawn By: J. RANDLE
Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

1"

Third angle projection.

1"

Drawing No:

ROPE SHEAVE
WOOD CLOCK WC5
WC5-00-03

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 2

1 3/8"
1 7/32"

5/64"

3/16"

1/64" X 45 TYP

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

2X

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

5/64" THRU ALL

SHAFT
WOOD CLOCK WC5
WC5-00-04

Material: 360 H02 BRASS

Sheet 1 of 1

No. Required: 2

9"
4"

1 7/8"

1 1/4"

6 1/4"
2 15/16"

2X

R1/4" TYP

1/2" THRU
2X

1 1/2"

2 7/8"

3/16" THRU

1 1/2"

1/2"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:2
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

Material: OAK

SHELF
WOOD CLOCK WC5
WC5-01-01

Sheet 1 of 1

No. Required: 1

3 3/4"
1/2"

R1/2"
R3"

R1/8" TYP

4"

2X

R1 1/2"

11/64" THRU

1 3/4"

18"

R26 13/64"
15 3/8"

23 1/4"

1/2"

R3/4"

1/2"

3 3/4"
3/16"

9"

1 3/4"
R3/4"

10 3/8"

R1 1/2"
4"

R3"
R1/2"
3 3/4"
Drawn By: J. RANDLE
Drawn Date: 09/12/05
Drawing Scale: 1:4
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

Material: OAK

BACK PLATE
WOOD CLOCK WC5
WC5-01-02

Sheet 1 of 1

No. Required: 1

1/2"

5"

R3/4"
2 7/8"

3 1/2"
R1 7/8"

R1"

2 7/8"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:2
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

Material: OAK

BRACE
WOOD CLOCK WC5
WC5-01-03

Sheet 1 of 1

No. Required: 2

5 1/4" REF
4 1/4"
12
15/32"

6
15/64"

3/16"

1" TYP

4X
R45 61/64"

13/64" THRU

7/8"
R45 61/64"

1"

11 7/32"

7 1/4"

5/8"

2 15/32"

R4"

R1/4" TYP

1 1/2"

R1/2"
7"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:2
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

FRAME PLATE, REAR

WOOD CLOCK WC5
WC5-02-01

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

1 1/8"

6
15/64"

1 1/8"

2 59/64"

2 19/64"
REF

2 1/4"
REF
5X

2 5/8"
REF

5/16" THRU

9 27/32"

7 27/32"
7 5/8"

3 1/8"

2 1/8"

1/2" THRU

SEE DRAWING WC5-02-01FOR DIMENSIONS NOT SHOWN

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:2
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

FRAME PLATE, MIDDLE

WOOD CLOCK WC5
WC5-02-02

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

6
15/64"
9
23/64"
9
23/64"

5/16" THRU

1/8"

3/4"

1 3/8"
5/64"
THRU ALL
3/16" THRU

SECTION A-A

A
3/4"

2 1/2"

6
15/64"

7" B.C.

4X
11/64" THRU
EQUALLY SPACED
ON BOLT CIRCLE

45
SEE DRAWINGS WC5-02-01 & WC5-02-02
FOR DIMENSIONS NOT SHOWN

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:2
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

FRAME PLATE, FRONT

WOOD CLOCK WC5
WC5-02-03

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

1/16"
1/16"
1/16"

3
1/8"

1/8"
3/16"

1/2"
3/4"

9/64"
TYP

9 1/2"

6 1/2"

7" B.C.

45

4X

11/64" THRU ALL

21/64" X 82
EQUALLY SPACED ON B.C.
6 TYP
30 TYP

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:2
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

DIAL
WOOD CLOCK WC5
WC5-02-04

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

2 5/32"

5/8"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

2X
5/32"
10-24 UNC

1"
7/8"

SECTION A-A

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

1"

Third angle projection.

1"

Drawing No:

Material: OAK

FRAME POST
WOOD CLOCK WC5
WC5-02-05

Sheet 1 of 1

No. Required: 8

5/8"

1/2"

11/64" THRU

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

Material: OAK

DIAL POST
WOOD CLOCK WC5
WC5-02-06

Sheet 1 of 1

No. Required: 4

7/8"
2X

3/16" THRU

7/16"

15/32"

1/32"
2 5/8" REF
1 1/8"
1/32"

3/16"

6
15/64"
Drawn By: J. RANDLE
Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

1/4"

3/8"

6
15/64"

2 5/32"

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

PENDULUM SUPPORT BRIDGE

1"

Third angle projection.

1"

Drawing No:

WOOD CLOCK WC5

WC5-02-07

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

1/16"

R1/16"

13/16"

1/64" X 45
5/32"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 2:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

PIN
WOOD CLOCK WC5
WC5-02-08

Material: 360 H02 BRASS

Sheet 1 of 1

No. Required: 1

3/4"
5/64" THRU ALL

1/4"
17.60
11/16"

6
15/64"
6
15/64"

5X
1/8" THRU
EQUALLY SPACED ON B.C.

3 13/16"
5"
4 1/4"
3/16"
38 TEETH

3 1/4" B.C.

3/8" THRU

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE
Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

WHEEL T-1
WOOD CLOCK WC5
WC5-03-01

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

2 27/32"
43/64"
3/8"

1/64" X 45

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

3/32" THRU ALL

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

1"

Third angle projection.

Drawing No:

1"

PIVOT
WOOD CLOCK WC5
WC5-03-02

No. Required: 1

Material: 360 H02 BRASS

Sheet 1 of 1

A
6
15/64"
9/64" THRU

1/8"

1/8"

1/8"

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

SECTION A-A

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

CLICK
WOOD CLOCK WC5
WC5-03-03-01

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 5

15
1/8"
1/4"

DETAIL A
SCALE 2 : 1

12
15/32"
3
1/8"
6
15/64"

3/8" THRU
REAM FOR FREE
FIT ON PIVOT

6
15/64"

3/4"

4 1/4"

3 1/8"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

ROPE PULLEY
WOOD CLOCK WC5
WC5-03-04

Sheet 1 of 2

Material: BALTIC BIRCH PLYWOOD No. Required: 1

8X

1/16"

1/2"

3 1/8"

45 TYP
2 3/4"

32

SECTION B-B
2 7/16"

4 1/4"

1 25/32"

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE
Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

ROPE PULLEY
WOOD CLOCK WC5
WC5-03-04

Sheet 2 of 2

Material: BALTIC BIRCH PLYWOOD No. Required: 1

SR.005 MIN

15/32"

19/32"

1/16"

THIS PART CAN BE MADE BY CUTTING THE HEAD

OFF A WIRE BRAD AND ROUNDING ITS TIP
Drawn By: J. RANDLE
Drawn Date: 09/12/05
Drawing Scale: 2:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

1"

Third angle projection.

Drawing No:

1"

ROPE PIN
WOOD CLOCK WC5
WC5-03-05

Sheet 1 of 1

No. Required: 8

Material: STAINLESS STEEL

5/64" THRU

1/32" X 45 TYP

1 9/32"

2 1/32"
3/8"

1/4"

1/4"

2X
3/16"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

5/64" THRU ALL

3/16"

5/8"

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

Material: OAK

1/2"

SHAFT
WOOD CLOCK WC5
WC5-04-01

Sheet 1 of 1

No. Required: 1

13/16"
1/4"
3/16"

1/64" X 45 TYP

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 2:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

3/32" THRU ALL

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

1"

Third angle projection.

1"

PIVOT (BACK)
WOOD CLOCK WC5

Drawing No:

WC5-04-02

Sheet 1 of 1

No. Required: 1

Material: 360 H02 BRASS

2 3/16"
2 1/64"
1 3/32"
3/8"
3/16"

3/32" THRU ALL

5/64" THRU ALL

1/64" X 45 TYP

3/32" THRU ALL

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 2:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

PIVOT (FRONT)
WOOD CLOCK WC5
WC5-05-01

Material: 360 H02 BRASS

Sheet 1 of 1

No. Required: 1

6
15/64"

6
15/64"

1/8"
54 TEETH

12
15/32"
12X
3/16" THRU
EQUALLY SPACED ON B.C.

R1/8"

1"

3/8"

2"

1"

GLUE LINES

4 43/64"

SECTION A-A

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

WHEEL T-2
WOOD CLOCK WC5
WC5-04-03

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

6
15/64"
6
15/64"

1 1/2"

1/8"

3/16" THRU

3/4"

1 1/4" HOLE CIRCLE

3/32" THRU ALL

15 X
1/8" THRU
EQUALLY SPACED ON H.C.
THIS DRAWING VIEW CAN BE USED AS A CUTTING
PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE
Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

1"

Third angle projection.

1"

Drawing No:

DISC
WOOD CLOCK WC5
WC5-05-02

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

9X

9
23/64"

1/8" THRU

1"

3/8" THRU

3/4" H.C.

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

DISC
WOOD CLOCK WC5
WC5-06-01

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

3
1/8"
3
1/8"

9/64"
48 TEETH

R1/8"

3/4"

5/16"

4 11/64"

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 0912/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

WHEEL T-HR
WOOD CLOCK WC5
WC5-05-03

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

3
1/8"
3
1/8"

4 7/16"

3/16" THRU

GLUE LINE

3/4"

3/32" THRU ALL

1/8" TO HOLE CENTER

THIS DRAWING VIEW CAN BE USED AS A CUTTING
PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

HAND (MINUTE)
WOOD CLOCK WC5
WC5-05-04

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

3
1/8"

3 3/16"

5/16" THRU

3/4"

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

HAND (HOUR)
WOOD CLOCK WC5
WC5-05-05

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

3
1/8"
6
15/64"

1/8"
45 TEETH

R1/8"

1"
3/8"

3 59/64"

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

WHEEL T-3
WOOD CLOCK WC5
WC5-06-02

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

3
1/8"
6
15/64"

1/8"
44 TEETH
9X

1/8" THRU

R1/8"

1"

3 53/64"

3/8" THRU

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

WHEEL T-4
WOOD CLOCK WC5
WC5-07-01

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

6
15/64"

3
1/8"

R1/8"
15 X
3/32" THRU
EQUALLY SPACED ON H.C.
2 3/8" HOLE CIRCLE
59/64" HOLE CIRCLE

1 3/16"

11 X
1/8" THRU
EQUALLY SPACED ON H.C.

2 5/8"

3/8" THRU
THIS DRAWING VIEW CAN BE USED AS A CUTTING
PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

ESCAPE WHEEL
WOOD CLOCK WC5
WC5-08-01

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

1 27/32"
17/64"

1 5/16"

3/16"

1/64" X 45 TYP

5/64" THRU ALL

3/32" THRU ALL

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 2:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

1"

Third angle projection.

1"

PIVOT
WOOD CLOCK WC5

Drawing No:

WC5-09-01

Material: 360 H02 BRASS

Sheet 1 of 1

No. Required: 1

5/64" THRU ALL

1"
1 9/64"

5/64"
3/16"

5/64" THRU ALL

1/64" X 45 TYP

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 2:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

PIVOT
WOOD CLOCK WC5
WC5-10-01

Material: 360 H02 BRASS

Sheet 1 of 1

No. Required: 1

3
1/8"
6
15/64"
9/64"
22 TEETH

1/8"

2"

3/4"

3/16" THRU

5/64" THRU ALL

THIS DRAWING VIEW CAN BE USED AS A CUTTING
PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

WHEEL T-6
WOOD CLOCK WC5
WC5-09-02

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

3
1/8"
6
15/64"

3/64"

1/8"

1"

3/4"
3/8"

2 1/4"

3/16"

1/64" X 45 TYP

3/32"

3/32" THRU ALL

THIS DRAWING VIEW CAN BE USED AS A CUTTING
PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

SECOND DISC
WOOD CLOCK WC5
WC5-09-03

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

3
1/8"
6
15/64"

9/64"
45 TEETH

12 X

1/8" THRU

R1/8"

1 1/4"

3 59/64"

5/16" THRU
THIS DRAWING VIEW CAN BE USED AS A CUTTING
PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

WHEEL T-INT
WOOD CLOCK WC5
WC5-10-02

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

3/8" THRU

3/4"

GLUE LINE

1/8" TYP

R1/64" MAX

5.99
15/64"
3
1/8"

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

ANCHOR
WOOD CLOCK WC5
WC5-11-01

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

6
15/64"

1/32"
1/2"
3/16" THRU

3/8"

1 1/2"

1/8"
2"

GLUE LINE
45

1/8" THRU

3/16"

5 1/2"

3/8"

1/8" THRU
6
15/64"

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

IMPULSE LEVER
WOOD CLOCK WC5
WC5-11-02

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

1/2"

6
15/64"
TYP

1/32"

1/4"

6
15/64"

1/16" THRU ALL

9/16"
1 1/2"
45 TYP

GLUE LINES
3/16" TYP
5 1/2"

9"

1/8"

1"

1/4"

R1/2" TYP
30 TYP

1 1/2"

1 3/4"

1 1/8"

1/2"
Drawn By: J. RANDLE
Drawn Date: 09/12/05
Drawing Scale: 2:3
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

LEADER
WOOD CLOCK WC5
WC5-12-01

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

1/2"

1 1/2"

3 3/4"

1/2"

5/64" THRU ALL

3/16"

1/16" X 45 TYP

5/8"

11/16"

3/4"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

Material: OAK

BOB GUIDE
WOOD CLOCK WC5
WC5-12-02

Sheet 1 of 1

No. Required: 1

3/16"

1/8"

3/32" THRU ALL

3 1/2"

2 1/2"
#10-32 UNF

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

ADJUSTING ROD
WOOD CLOCK WC5
WC5-12-03

Material: 360 H02 BRASS

Sheet 1 of 1

No. Required: 1

R1/8"

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

18
45/64"

SHELL HALF
WOOD CLOCK WC5
WC5-12-04-01

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 2

3"

R3 39/64"
REF

R1 1/2"
4 1/4"

R3 39/64"
REF

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

3
1/8"

SHELL COVER
WOOD CLOCK WC5
WC5-12-04-02

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 2

37/64"
6
15/64"

6
15/64"

15/32"
REF
R3/8"

15/32"
REF

3/16"

7/8"

1 15/32"

12
15/32"

GLUE LINE
TYP
2"

2"

THIS DRAWING VIEW CAN BE USED AS A CUTTING

PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

SHELL TOP
WOOD CLOCK WC5
WC5-13-01

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

10"

3
1/8"

"A"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:2
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

ITEM

DESCRIPTION

"A"

# REQD

WC5-13-02-A

FRONT/BACK PANEL

2 15/64

WC5-13-02-B

SIDE PANEL

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

SHELL SIDES
WOOD CLOCK WC5
WC5-13-02

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: SEE TABLE

3/4" THRU

2"

2"

12
15/32"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

1"

Third angle projection.

Drawing No:

1"

SHELL BOTTOM
WOOD CLOCK WC5
WC5-13-03

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

3/4" THRU

1 1/16"

1 1/16"

12
15/32"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

SHELL BOTTOM
WOOD CLOCK WC5
WC5-14-03

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

19/32"
6
15/64"
R3/8"

6
15/64"

3/16"

7/8"

1 15/32"

12
15/32"

GLUE LINE
TYP

1 1/16"

1 1/16"
THIS DRAWING VIEW CAN BE USED AS A CUTTING
PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT
THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS
OF THE BOX IN THE TITLE BLOCK.

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:1
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

SHELL TOP
WOOD CLOCK WC5
WC5-14-01

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: 1

5"

3
1/8"

"A"

Drawn By: J. RANDLE

Drawn Date: 09/12/05
Drawing Scale: 1:2
PROPRIETARY AND CONFIDENTIAL
The information contained in this
drawing is the sole property of
RANDLE DESIGN, LLC. Any reproduction in part or as a whole
without the written permission of
RANDLE DESIGN, LLC is prohibited.

ITEM

DESCRIPTION

"A"

# REQD

WC5-14-02-A

FRONT/BACK PANEL

1 19/64

WC5-14-02-B

SIDE PANEL

1 1/16

All dimensions are in inches

Tolerance +/-.005" typical.

Description:

OK to scale drawing only if

box to right is full scale.

Project:

Third angle projection.

1"
1"

Drawing No:

SHELL SIDES
WOOD CLOCK WC5
WC5-14-02

Sheet 1 of 1

Material: BALTIC BIRCH PLYWOOD No. Required: SEE TABLE