Assembly Instructions

Basic Folding-Leg Box Frame Style

Basic Folding Leg Cornhole Board Concept

1
2

12

15
316

31
2

41
4

52

R13
4
6

21

121
4

48

Bolt
Washer

913
16
35

Washer
Double Nut

CornholePlayers.net

Jackson Van Buren

Materials
Lumber
(4)

(2)

8 length structural 24s

1
2448 sheets in plywood
2

Hardware

(4)

(4)

4 long

3
carriage bolts
8

3
fender washers
8
3
(8)
locknuts
8
(56) 3 deck screws

Tools (recommended)
Power Drill

Miter Saw

Belt Sander

Plunge Router or 6 in
Hole Saw

Wood Glue

Measuring Tape

Clamps

Drill Bits (philips, pilot,

and 3/8 in)

Radial Arm Saw

Orbital Sander

Step 1 Prepare the lumber

Cutting templates (A and B) are given as visual reference for 8 ft section cuts Cut 2
sections as given in A and 2 as given in B . When all the cuts have been made, you
should have 4 Long Side and 4 Short Side segments, 4 Legs, and 2 Cross Beams.*
Select one of the 8 ft of sections. Use cutting template A for reference. Make a cross cut
48 in from the butt of the board. This segment will be the Long Side of the box frame.
Then make another cross cut at 21 in. This segment will be the Short Side of the box

frame. Use these 48 in and 21 in segments as templates for making similar cuts. Cut
another 21 in segment. Discard the approximate 6 in scrap.

See Notes section about Cross Beam alternative uses

-3-

Repeat with another 8 ft section, using your Long Side and Short Side segments as cutting
guides.
Now implement cutting template B. Set the
miter to 35. Select another 8 ft section and
make the following cut as shown. With the
miter saw still set at 35 make the same cut on
the last remaining 8 ft section. These
segments will be the Legs. Now reset the
miter angle to perpendicular.
Use a Leg segment youve already cut as a guide by flipping it, stacking on top and lining
up the mitered edge with the mitered edge of the lumber. Crosscut the lumber at the Leg
segment butt end. Now cut a 48 in segment. Then cut an 18 in segment. This last segment
will be the Cross Beam. Discard the approximate scrap.
Repeat on the last remaining section of lumber, using guides as helpful.

Step 2 Construct the Box

Gather the 48 in and 21 in segments and plywood sheets.
If framing or box clamps are available to you, now would
be a good time to grab them. Mock up or dry fit the
pieces together on level ground. The longer segments
should sandwhich the shorter ones between them.
To ensure the box frame is square and you dont have
access to framing clamps
or a corner jig or anything
of that nature, you can do
this: Measure the
diagonals and adjust the
pieces until that
measurment is the same. (eg ab = cd)
When you are satisfied with your mock up, drill pilot
holes through the corners for your 3 in deck screws. Drill 2 pilots per corner on center
with the backing 21 in piece. the Then proceed with wood glue and the screws.
Periodically check to make sure your frames are
square. Sink the screws to atleast flush with the
board face.
Place the sheet of plywood over the box frame and
adjust its position so that full coverage of the box
frame is achieved. Dont be concerned if the
plywood overhangs the frame, however. That will
be sanded down at a later time.

-4-

Drill pilots through the plywood into the box

frame about every 6 in. Placement will matter
for aesthetic reasons if you are not planning on
painting eventually. Also make sure not to drill
into the horizontal screws holding the box frame
together.
Remove the plywood taking care to note its
orientation. Apply a bead of wood glue and
replace the plywood right back where it was.Use
your pilot holes for reference. Start shooting
screws working your way around the board. At this point, go back and make sure all the
heads of your deck screws are sunk at least flush with the surface. If you plan on
puttying, sink them below the surface.
Repeat for the other box assembly.
Once the glue has dried (and the putty if youve applied it,) use a belt sander with a heavy
grit to take down any imperfections in the plywood and box frame marriage. Then finishsand the boards with an orbital sander to take out any blemishes.

Step 3 Cut the Hole

There are a lot of ways to do this. For all of which however, youll have find the center
first. ACA specifies that hole should measure 6 in in diameter, centered at a point 9 in
from the trailing edge aligned to the middle of the board. So make a mark here on both
boards. To cut the hole, Ill touch on two methods:

A. 6 inch Hole Saw

This definitely the easier of the two. Hole saws are expensive but if you can
borrow one, I would strongly recommend you use this method. All you have
to do is put a 6 in hole saw bit on the mandrel and drill into your center mark
with through they plywood.

B. Circle Jig
You can use a router, a spiral saw (often called a roto-zip), or even a Dremel
tool with this method. NOT JIGSAWS
though, -the cutting blade has to be
radially symmetric.
The concept here is simple; it works
just like a compass. First make
yourself a jig similar to the one shown.
You can do this with a paint stick and
nail at the pin. Make the distance
between the pin center and the outer
edge of the cutting blade 3 in. Drill a
pivot point into the center mark on the
board and a starter hole on the
circumference of the circle (anywhere
3 inches away from the center mark.) Then set up your jig on the boards, turn
on your tool, and rotate around the center mark until youve cut out a circle.

-5-

Note: Spiral saw bits break very easily. Save yourself an

unnecessary trip to the hardware store by cutting slowly
and backing out frequently.
To clean up your cuts, make yourself a contour sander out of sandpaper and a spray paint
can. Then hand sand the holes to your liking.

Step 4 Make the legs

Return now to Leg segments you cut in step 1. The primary design
that weve been following thus far, utilizes circular filets at the
pivot points. To create those filets, use the circle jig method
outlined in step 3. The radius you should set the jig to is one half
the width of the Leg (1.75 in.) The center is at a point 1.75 in from
the butt end and an equidistant 1.75 in from both sides. MARK
THIS CENTER WHEATHER OR NOT YOU ARE ROUNDING
YOUR LEGS.
Granted the circular pivots are structurally and aesthetically beneficial, but they do take a
certain degree of craftsmanship to achieve. Fortunately, any contour will also work so
long as the cut-lines are inside of a bounding radius of 1.75 in. A common alternative to
circular legs, are notched
ones. One can simply notch
the legs by cutting 2
opposing 45 miters and then
taking down the point with a
cross cut or sanding.
Whatever method you choose, all of your
Legs should be uniform. A convenient way
to ensure that is to clamp them all together
and sand them flush.
Lastly, bore out a hole for the bolt through
the center mark you made earlier. Use a 3/8
in bit. Use an awl or drill starter hole so that
the bit doesnt wander. It is crucial that the
direction of the bore be as close to normal to
leg face as possible. (STRAIGHT down.) If
you have a drill press or a perpendicular
guide, use it.
Repeat for each Leg.

To find out why, read the Notes section.

-6-

Step 5 Attach the legs to the Boards

Flip your boards so that the open box is facing up. Measure 4 1/4 in from the edge of the
board and clearly mark a line as shown in the image below. Place one of your finished
legs with the shorter end facing down
into the box so that it is flush with the
back of the plywood and lapped against
the long side of the box. Slide the leg
along until the center of the hole in the
leg is inline with the mark you made on
the board. Clamp the leg segment in
place bore a 3/8 in hole into the box
frame using the leg center hole as a
guide.
Repeat for each leg in each corner.
Now assemble the folding legs to the box using a carriage bolt, a washer, and 2 locknuts
per leg as shown below. Tighten the nut closest to the washer to cinch the carriage bolt
head flush to the outer surface. Then loosen according to how much friction youd like in
the pivot. Then tighten the outer nut to
lock everything in place.
Do that for each leg.
The boards are now completely assembled
from a structural standpoint. If you
choose, can employ any of the optional
steps mentioned in the Notes section. Or
you can just add bags and start playing!
Many Cornhole enthusiasts, however,
would move on to finishing steps. This can
be anything from staining to painting to
applying decals Whatever it may be,
further instruction would be beyond the
scope of these instructions.
Happy Cornholing!

-7-

Notes:
The Cross Beam (as dimensioned here) an optional component. It gets sandwiched
between the folding legs so that they fold as one. This feature is not uncommon.
Generally it is held in with 4 screws, 2 shot though each leg. It poses a problem when
youre not playing on flat ground though. Bascially it will lean or or one side will not
touch the ground. The boards will be more rigid in the axis perpendicular to the direction
youd normally be throwing at them but youd lose that independent suspension that
separate legs have.
One could also choose to use the Cross Beams segments for additional box frame
rigidity. The box frame would look like a boxed H frame. All youd have to do, is
substitute Short Side dimensions for every mention of Cross Beam in Step 1. This would
probably cut down further on bounce and add a little more weight.
Circular filets on the leg pivots do one thing that filets of any other geometry cant. That
is adding another point of contact for impact to be translated to the ground. With notched
legs, all the impact energy associated with a bag toss (or whatever youre throwing at
your boards) will be absorbed and concentrated into shear stress in the bolts. The circular
filets actully are tangent to the back of the board surface so that impact can be directly
translated through the leg member into the ground.

General Design Notes:

Why did I call for 2 separate sheets of plywood instead of one 4by8? So anyone can fit
them into their car (myself included.) Get the 4by8 cut at the store if they dont stock it.
Why 3/8 inch hardware? Bigger (at least inch) is better within reason of course. The
thing is that chucks on most average consumer level drills cant take a bit that big. If
youve got a set of spade bits or a good drill however, Id bump it up a notch. With spade
bits you just have to be extra careful to drill perfectly straight in or your hardware have a
significant amount of play.

-8-