Water injection (engine)

In internal combustion engines, water injection, also known as anti-detonant injection (ADI), can
spray water into the incoming air or fuel-air mixture, or directly into the cylinder, in order to cool
certain parts of the induction system where "hot points" could produce premature ignition. In jet
engines it is used to increase the thrust of the engine at low speeds and at takeoff.
Water injection was used historically to increase the power output of military aviation engines for
short durations such as dogfights or takeoff, however it has also been used in motor sport and
notably in drag racing. In Otto cycle engines the cooling effects of water injection also allow for
greater compression ratios by reducing the problem of engine knocking (detonation). Alternately this
reduction in engine knocking in Otto cycle engines means that in some applications significant
performance gains can be obtained when water injection is used in conjunction with
a supercharger, turbocharger and/or other modifications such as a more aggressive ignition timing.
Depending on the engine, improvements in power and fuel efficiency can also be obtained solely by
injecting water.[1] Water injection may also be used to reduce NOx or carbon monoxide emissions.[1]
Water injection is also used in some turbine engines and in some turboshaft engines, normally when
a momentary high-thrust setting is needed to increase power and fuel efficiency.

Theory[edit]
Water has a very high heat of vaporization. As the ambient temperature water is injected into the
engine, heat is transferred from the hot cylinder head/ intake air into the water. This causes it to
evaporate, cooling the intake charge. A cooler intake charge means it is more dense (higher
volumetric efficiency) and also will have a lower tendency to knock. However the water vapor will
displace some air, negating some of the denser intake charge benefit. Knocking is generally more of
a problem in forced induction engines rather than naturally aspirated so this can be a useful aid in its
prevention. On electronic ignition systems the ignition timing is generally retarded to prevent knock
from occurring but with water injection it can be advanced closer to Maximum Brake Torque (MBT)
timing for additional power.

Composition of fluid[edit]
Many water injection systems use a mixture of water and alcohol (often close to 50/50), with trace
amounts of water-soluble oil. The water provides the primary cooling effect due to its
great density and high heat absorption properties. The alcohol is combustible, and also serves as
an antifreeze for the water. The main purpose of the oil is to prevent corrosion of water injection and
fuel system components;[2] it may also assist in engine lubrication when running in a high power
state.[citation needed] Because the alcohol mixed into the injection solution is often methanol (CH3OH), the
system is known as methanol-water injection, or MW50. In high performance automotive
applications some tuners use 100% methanol as opposed to a water-methanol mixture and then
referred to simply as "methanol injection". Safety concerns and part longevity concerns keep this as
a controversial option. In the United States, the system is also commonly referred to as anti-detonant
injection, or ADI.

Effects[edit]
In a piston engine, the initial injection of water cools the fuel-air mixture significantly which increases
its density and hence the amount of mixture that enters the cylinder. The water (if in small liquid
droplets) may absorb heat (and lower the pressure) as the charge is compressed, thus reducing
compression work.[1] An additional effect comes later during combustion when the water absorbs

large amounts of heat as it vaporizes, reducing peak temperature and resultant NOx formation, and
reducing the amount of heat energy absorbed into the cylinder walls. This also converts part of
combustion energy from the form of heat to the form of pressure. As the water droplets vaporize by
absorbing heat, they turn to high pressure steam. The alcohol in the mixture burns, but is also much
more resistant to detonation than gasoline. The net result is a higher octane charge that will support
very high compression ratios or significant forced induction pressures before onset of detonation.
Certain other engines can benefit far more from the use of water injection. Typical pulse jet engines
have extremely poor fuel efficiency, specific fuel consumption, and thrust. Water injection has been
proven to use the waste heat that causes a pulse jet to glow red hot and convert it into thrust. It
cools the engine, it pulls more air in, and it reduces pollution. Water injection and other means of
boost may be able to transform the pulse jet from a noisy, inefficient tube to a cleaner burning and
powerful enough engine that may be of use in lightweight aircraft[citation needed].
Fuel economy can be improved with water injection. Depending on the engine, the effect of water
injection, with no other modification, like leaning out the mixture, may be quite significant.[1] In some
cases water may also reduce CO emissions. This may be attributable to the water gas shift reaction,
in which CO and H2O shift to form CO2 and H2.[1]However, water may also increase hydrocarbon
emissions, possibly due to an increased quenching layer thickness.
Some degree of control over the water injection is important. It needs to be injected only when
conditions within the engine would otherwise be sufficient to cause detonation or other undesirable
effects. This normally occurs when the engine is heavily loaded and running at full power, however
may occur outside of these times in specialized engines or applications. Otherwise injecting water
cools the combustion process unnecessarily, resulting in negative effects such as reduced efficiency
or power.
Direct injection of water is possible and is likely advantageous. In a piston engine, this may be done
at any point in the engine's cycle, depending on the desired effect, even late in the power stroke or
during the exhaust stroke when used only to reduce engine temperatures.

Limitations[edit]
Most modern consumer vehicle engines are pre-programmed with specific fuel-to-air ratios,
therefore introducing water without re-programming the car's computer or otherwise changing these
ratios will most likely not have any benefit and will often reduce performance or cause damage to the
engine[citation needed]. In addition most modern fuel systems cannot determine that water in any form has
been added and cannot determine a new compression ratio or otherwise take advantage of lower
cylinder temperatures. In most cases in cars that are pre-programmed, introducing water vapor via
an indirect water injection method will cause loss of power because the water vapor will take the
place of air (and fuel in engines with either a carburetor or single point injection) that is required to
complete the combustion process and produce power. Normally only in vehicles in which the owner
re-tunes the vehicle for water injection will any benefits be seen.
Damage can occur to the engine if too much water is injected or if there is a malfunction of the
injector itself. Water is not compressible and if too much water makes it into the cylinder prior to, or
during, the compression cycle, it can result in a condition called hydrolock, where the volume of
liquid in the engine is close to or greater than the volume between piston and head (or between
pistons in a opposed piston engine) of the engine at top dead center, resulting in extremely high
cylinder pressure that may cause blown heads, shattering of the piston, connecting rods or other
damage to the engine. This damage is normally fatal to the engine and typically requires a full
rebuild or engine replacement.
Water injection is typically used in aviation and was not initially intended for use in consumer grade
vehicles. When used in consumer grade vehicles it is normally for the extremely high performance
arena (1000 HP+) where vehicles are supercharged or turbocharged and produce excessive heat.
These vehicles are typically driven only in an event or controlled race and require extremely high

levels of knowledge to maintain and are only driven for very short distances. In most forms of water
injection, water is mixed with a combustible fuel rather than being used in isolation.
Many product scams exist[citation needed] touting that inserting a tube of misting spray into an intake
manifold will increase your mileage gains or horsepower. However, unless the user reprograms the
car's ECU and/or performs major modifications to the engine, power loss and damage may
eventually occur.

Use in aircraft[edit]

A "wet" takeoff of a KC-135 with J57engines

Water injection has been used in both reciprocating and turbine aircraft engines. When used in a
turbine engine, the effects are similar, except that normally preventing detonation is not the primary
goal. Water is normally injected either at the compressor inlet or in the diffuser just before the
combustion chambers. Adding water increases the mass being accelerated out of the engine,
increasing thrust, but it also serves to cool the turbines. Since temperature is normally the limiting
factor in turbine engine performance at low altitudes, the cooling effect allows the engine to be run at
higher RPM with more fuel injected and more thrust created without overheating.[3] The drawback of
the system is that injecting water quenches the flame in the combustion chambers somewhat, as
there is no way to cool the engine parts without coincidentally cooling the flame. This leads to
unburned fuel out the exhaust and a characteristic trail of black smoke.
Piston engined petrol military aircraft utilized water injection technology prior to World War II in order
to increase takeoff power. This was used so that heavily-laden fighters could take off from shorter
runways, climb faster, and quickly reach high altitudes to intercept enemy bomber formations. Some
fighter aircraft also used water injection to allow higher boost in short bursts during dogfights.
As a general rule, the fuel mixture is set at full rich on an aircraft engine when running it at high
power settings (such as during takeoff). The extra fuel does not burn; its only purpose is
to evaporate to absorb heat. This uses fuel faster and also decreases the efficiency of the
combustion process. By using water injection, the cooling effect of the water allows the fuel
mixture to be run leaner at its maximum power setting. Many military aircraft engines of the 1940s
utilized a pressure carburetor, a type of fuel metering system similar to a throttle body
injection system. In a water-injected engine, the pressure carburetor features a
mechanical derichment valve which makes the system nearly automatic. When the pilot turns on the
water injection pump, water pressure moves the derichment valve to restrict fuel flow to lean the
mixture while at the same time mixing the water/methanol fluid into the system. When the system
runs out of fluid the derichment valve shuts and cuts off the water injection system, while enriching
the fuel mixture to provide a cooling quench to prevent sudden detonation.
Due to the cooling effect of the water, Otto cycle aircraft engines with water injection can be made to
produce more power through higher charge densities at the time of combustion. The additional
charge density is typically achieved by allowing higher manifold pressures to be used before the
onset of detonation; this is normally done by adding or increasing the amount of forced induction or

further opening of the throttle, however a similar result may also be achieved via higher engine
stoke. This has historically been the primary use of a water injection systems in aircraft.
The extra weight and complexity added by a water injection system was considered worthwhile for
military purposes, while it is usually not considered worthwhile for civilian use. The one exception
is racing aircraft, which are focused on making a tremendous amount of power for a short time; in
this case the disadvantages of a water injection system are less important.
The use of water injection in turbine engines has been limited, again, mostly to military aircraft. Many
pictures are available of Boeing B-52 takeoffs which clearly show the black smoke emitted by turbine
engines running with water injection. For early B-52s, water injection was seen as a vital part of takeoff procedures. For later versions of the B-52 as well as later turbine-powered bombers, the problem
of taking off heavily loaded from short runways was solved by the use of more powerful engines that
had not been available previously.
The BAC One-Eleven airliner also used water injection for its Rolls-Royce Spey turbofan engines.
Filling the tanks with jet fuel instead of water led to the Paninternational Flight 112 crash.[4]

Use in automobiles[edit]
A limited number of road vehicles with forced induction engines from manufacturers such
as Chrysler have included water injection. The 1962 Oldsmobile F85 was delivered with the FluidInjection Jetfire[5] engine, which, incidentally, shares the title of "the world's first turbocharged road
car" with the Corvair Spyder. Oldsmobile referred to the water/alcohol mixture as 'Turbo-Rocket
Fluid'. Saab offered water injection for the Saab 99 Turbo. With the introduction of the intercooler the
interest in water injection to prevent detonation almost disappeared, but recently water injection has
also been of interest because it can potentially decrease nitrogen oxide (NO) and carbon
monoxide (CO) emissions in exhaust. However the most common use of water injection today is in
vehicles with high performance aftermarket forced induction systems (such as turbochargers or
superchargers); such engines are commonly tuned with a narrower margin of safety from detonation
and hence benefit greatly from the cooling effects of vaporized water.[citation needed]
In 2015 BMW has introduced a version of their high performance M4 coupe, the M4 GTS, that
combines water injection with intercooling. The car was featured in the 2015 MotoGP season as the
official safety car for the series and was released for the commercial market in 2016.[6] Bosch, which
co-developed the technology, offers a water injection system named WaterBoost for other
manufacturers. The company claims up to 5% increase in engine performance, up to 4% decrease
in CO2 emissions and up to 13% improvement in fuel economy.[7]