Worldwide Contacts

www.tyco-fire.com

Worldwide
Contacts

www.tyco-fire.com

Resilient-Seated Gate Valves

Outside Screw and Yoke
General
Description

TYCO Resilient-Seated Gate Valves

are used in Fire Protection Systems
for on/off operation. End connection
configurations including Flange by
Flange, Flange by Groove, and Groove
by Groove are available.
The ductile Iron body weighs approximately 50% less than conventional
cast iron valves, which allows easier
handling on site and reduced shipping
costs.
The fully encapsulated EPDM ductile iron Wedge ensures bubble-tight
sealing.
Valve components are either inherently corrosion-resistant or protected
with fusion-bonded epoxy resin coating for a long, dependable service life
and enhanced UV protection in exposed installations.
This valve is one of the lightest, most
durable gate valves on the market today. Its design features and material
selection criteria fulfill the need for a
dependable, long life and easy to operate gate valve.

NOTICE
Never remove any piping component
nor correct or modify any piping deficiencies without first de-pressurizing
and draining the system. Failure to do
so may result in serious personal injury, property damage, and/or impaired
device performance.
It is the designers responsibility to select products suitable for the intended
service and to ensure that pressure
ratings and performance data are not
exceeded. Material and gasket selection should be verified for compatibility with the specific application. Always
read and understand the installation
instructions.
TYCO Gate Valves described herein must be installed and maintained
in compliance with this document, in
addition to the standards of any other
authorities having jurisdiction. Failure
to do so may result in serious personal injury or impair the performance of
these devices.
The owner is responsible for maintaining their mechanical system and devices in proper operating condition.
The installing contractor or device
manufacturer should be contacted
with any questions.

Technical
Data
Sizes
2 (DN50), 2-1/2 (DN65), 3 (DN80),
4 (DN100), 6 (DN150), 8 (DN200),
10 (DN250), and 12 (DN300)
Approvals
UL Listed
FM Approved
Maximum Working Pressure
UL - 300 psi (20,87 bar)
FM - 232 psi (16 bar)
Flanges
ASME B16.1/ASME B16.42
EN 1092-2/ISO 7005-2
Drilled to ANSI 125/150 or PN10/PN16
or AS 2129 (Table E).
Materials of Construction
See valve parts list, Figure 1.

Page 1 of 6

DECEMBER 2013

TFP1540

TFP1540
Page 2 of 6

15

14
16
17

12

10

22

11

17

13

13

19

20
18

6
4

21

18
14
3
2
1

NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22

DESCRIPTION
QTY.
Wedge . . . . . . . . . . . . . 1
Wedge Nut . . . . . . . . . . 1
Stem Pin . . . . . . . . . . . 1
Sealing Gasket . . . . . . 1
Sealing O-Ring . . . . . . 3
Stem Guide . . . . . . . . . 1
Stem O-Ring . . . . . . . . 2
Compression Washer . . 1
Top Gland . . . . . . . . . . 1
Washers . . . . . . . . . . . 2
Top Nut . . . . . . . . . . . . 2
Handwheel . . . . . . . . . . 1
Yoke . . . . . . . . . . . . . . 1
Stem . . . . . . . . . . . . . . 1
Gland Stud . . . . . . . . . . 2
Gland Hex Nut . . . . . . . 2
Flat Washer . . . . . . . . . 4
Bonnet . . . . . . . . . . . . . 1
Screw Grouting . . . . . . 1
Bonnet Screw . . . . . . . 4
Body . . . . . . . . . . . . . . . 1
Yoke Hex Nut . . . . . . . . 2

MATERIAL
EPDM Coated Ductile Iron
Bronze
Stainless Steel
EPDM
NBR
Bronze
NBR
Stainless Steel
FBE Coated Ductile Iron
Bronze
Bronze
FBE Coated Ductile Iron
FBE Coated Ductile Iron
Stainless Steel
Zinc Coated Carbon Steel
Zinc Coated Carbon Steel
Zinc Coated Carbon Steel
FBE Coated Ductile Iron
Activated Resin
Black Oxide Carbon Steel
FBE Coated Ductile Iron
Zinc Coated Carbon Steel

FIGURE 1
OUTSIDE SCREW AND YOKE GATE VALVE
ASSEMBLY

Installation
In piping systems, TYCO ResilientSeated Gate Valves should be located where operation, inspection, and
maintenance are readily accessible.

Care and
Maintenance

The TYCO Resilient-Seated Gate

Valves must be maintained and serviced in accordance with this section.
Before closing a fire protection system
main control valve for maintenance
work on the fire protection system that
it controls, obtain permission to shut
down the affected fire protection system from the proper authorities and
notify all personnel who may be affected by this decision.
After placing a fire protection system
in service, notify the proper authorities
and advise those responsible for monitoring proprietary and/or central station alarms.

The owner is responsible for the inspection, testing, and maintenance of

their fire protection system and devices in compliance with this document,
as well as with the applicable standards of the National Fire Protection
Association (e.g., NFPA 25), in addition
to the standards of any authority having jurisdiction. The installing contractor or product manufacturer should be
contacted relative to any questions.
Any impairments must be immediately
corrected.
Automatic sprinkler systems are recommended to be inspected, tested,
and maintained by a qualified Inspection Service in accordance with local
requirements and/or national codes.
See Figure 1 for valve components
referenced in this section.
Debris lodged in the sealing area of
the Wedge (1) may cause the valve
to close hard. Backing off the Handwheel (12) and closing it again, several times if necessary, can correct this
problem.

The valve should never be forced to

seat by applying a wrench or extension to the Handwheel (12), as it may
distort the valve components or score
the sealing surfaces. All replacement
parts must be obtained from the manufacturer to assure proper operation
of the valve.
At initial valve installation the Gland
Hex Nuts (16) should be left only finger tight to allow the Gland (9) to remain in a relaxed state during normal valve operation. For applications
where the valve is subject to vibration,
a non-hardening thread sealant may
be applied to the Gland Hex Nuts (16)
to prevent self-loosening and subsequent disengagement of the Gland (9).
If leakage past the Sealing O-Rings (5)
occurs, evenly tighten the Gland Hex
Nuts (16) until the leakage ceases.

TFP1540
Page 3 of 6
OPEN

SHUT

CL1
CL2

FLANGE x FLANGE

FLANGE x GROOVE

GROOVE x GROOVE

Nominal
Valve
Size

Nominal
Pipe Size

Nominal
Handwheel
Turns
to Fully
Operate
(Open or
Shut)

Approx.
Weight
FxF
Lbs.
(kg)

Approx.
Weight
FxG
Lbs.
(kg)

Approx.
Weight
GxG
Lbs.
(kg)

ANSI
Inches
DN

O.D.
Inches
(mm)

CL1

CL2

2
DN50

2.375
(60,3)

7.00
(178)

15.55
(395)

13.07
(332)

13

29.8
(13,5)

27.6
(12,5)

25.4
(11,5)

2-1/2
DN65

2.875
(73,0)

7.50
(190)

16.14
(410)

13.31
(338)

16

35.3
(16)

30.9
(14)

26.5
(12)

DN65

3.000
(76,1)

7.50
(190)

16.14
(410)

13.31
(338)

16

30.9
(14)

26.5
(12)

3
DN80

3.500
(88,9)

8.00
(203)

18.9
(480)

14.96
(380)

20

41.9
(19)

36.4
(16.5)

30.9
(14)

4
DN100

4.500
(114,3)

9.00
(229)

22.56
(573)

17.72
(450)

20

57.3
(26)

50.7
(23)

44.1
(20)

DN150

6.500
(165,1)

10.50
(267)

29.53
(750)

23.31
(592)

25

88.2
(40)

79.4
(36)

6
DN150

6.625
(168,3)

10.50
(267)

29.53
(750)

23.31
(592)

25

97.0
(44)

88.2
(40)

79.4
(36)

8
DN200

8.625
(219,1)

11.50
(292)

37.64
(956)

29.45
(748)

34

154.4
(70)

143.3
(65)

110.3
(50)

10
DN250

10.750
(273,1)

13.00
(330)

46.26
(1175)

34.96
(888)

42

264.6
(120)

242.6
(110)

220.5
(100)

12
DN300

12.750
(323,9)

14.00
(356)

51.89
(1318)

39.57
(1005)

50

330.8
(150)

297.7
(135)

275.6
(125)

Nominal Dimensions
Inches (mm)

FIGURE 2
OUTSIDE SCREW AND YOKE GATE VALVE
NOMINAL DIMENSIONS

TFP1540
Page 4 of 6
Nominal
Valve Size

Nominal Dimensions in Inches (mm)

ANSI
Class 150

ANSI
Inches
DN

ISO 7005-2
PN16

AS 2129
(Table E)

Dim.
A

Dim.
B

Qty.
N

Dim.
A

Dim.
B

Qty.
N

Dim.
A

Dim.
B

Qty.
N

2
DN50

4.75
(120,5)

0.75
(19)

4.92
(125,0)

0.75
(19)

4.48
(114,0)

0.71
(18,0)

2-1/2
DN65

5.50
(139,5)

0.75
(19)

5.71
(145,0)

0.75
(19)

5.00
(127,0)

0.71
(18,0)

3
DN80

6.00
(152,5)

0.75
(19)

6.30
(160,0)

0.75
(19)

5.74
(146,0)

0.71
(18,0)

4
DN100

7.50
(190,5)

0.75
(19)

7.09
(180,0)

0.75
(19)

7.00
(178,0)

.071
(18,0)

6
DN150

9.50
(241,5)

0.88
(22)

9.45
(240,0)

0.88
(23)

9.25
(235,0)

0.87
(22,0)

8
DN200

11.75
(298,5)

0.88
(22)

11.61
(295,0)

0.88
(23)

12

111.49
(292,0)

0.87
(22,0)

10
DN250

14.25
(362,0)

1.00
(25)

12

13.98
(355,0)

1.13
(28)

12

14.02
(356,0)

0.87
(22,0)

12

12
DN300

17.00
(432,0)

1.00
(25)

12

16.14
(410,0)

1.13
(28)

12

15.98
(406,0)

1.02
(26,0)

12

Dim. A
Bolt Circle
Diameter
Dim. B
Bolt Hole
Diameter
Qty. N
Number of
Bolt Holes

FIGURE 3
GATE VALVE FLANGE
NOMINAL DIMENSIONS

600

800 1000

20000

30000
0,020

)
300

H(

DN

250
DN
H(
INC

INC
12

)
10

(DN

150

CH

(DN

8 IN

CH
6 IN

200

)
100
4 IN

CH

(DN

80)
(DN

3 IN

CH

H(
INC
/2

0.10
0.09
0.08
0.07

2-1

CH

(DN

DN

50)

65)

0.20

2 IN

NOMINAL PRESSURE DROP

IN POUNDS PER SQUARE INCH (PSI)

0.30

0,006
0,005

0.06
0.05
100

0,010
0,009
0,008
0,007

0,004
200

300

400
600 800 1000
2000
3000 4000
FLOW RATE IN GALLONS PER MINUTE (GPM)

GRAPH A
GATE VALVE FRICTION LOSS

6000

10000

NOMINAL PRESSURE DROP IN BAR

(1 PSI = 0.06895 BAR)

400

FLOW RATE IN LITRES PER MINUTE (LPM)

(1 GPM = 3.785 LPM)
2000
3000 4000
6000
10000

TFP1540
Page 5 of 6
Nominal
Valve
Size

Nominal
Pipe
Size

ANSI
Inches
DN

O.D.
Inches
(mm)

Flange x
Flange
ANSI
Class 150

Flange x
Flange
ISO 7005-2
PN16

Flange x
Groove
ANSI
Class 150

Flange x
Groove
ISO 7005-2
PN16

Flange x
Flange
AS 2129
(Table E)

Groove x
Groove

2
DN50

2.375
(60,3)

TMRX-0500003

TMRX-0500001

TMRT-0500603

TMRT-0500601

TMRX-0500005

TMRG-0500604

2-1/2
DN65

2.875
(73,0)

TMRX-0650003

TMRX-0650001

TMRT-0650733

TMRT-0650731

TMRX-0650005

TMRG-0650734

DN65

3.000
(76,1)

TMRT-0650763

TMRT-0650761

TMRG-0650764

3
DN80

3.500
(88,9)

TMRX-0800003

TMRX-0800001

TMRT-0800893

TMRT-0800891

TMRX-0800005

TMRG-0800894

4
DN100

4.500
(114,3)

TMRX-1000003

TMRX-1000001

TMRT-1001143

TMRT-1001141

TMRX-1000005

TMRG-1001144

DN150

6.500
(165,1)

TMRT-1501653

TMRT-1501651

TMRG-1501654

6
DN150

6.625
(168,3)

TMRX-1500003

TMRX-1500001

TMRT-1501683

TMRT-1501681

TMRX-1500005

TMRG-1501684

8
DN200

8.625
(219,1)

TMRX-200-003

TMRX-2000001

TMRT-2002193

TMRT-2002191

TMRX-2000005

TMRG-2002194

10
DN250

10.750
(273,1)

TMRX-2500003

TMRX-2500001

TMRT-2502733

TMRT-2502731

TMRX-2500005

TMRG-2502734

12
DN300

12.750
(323,9)

TMRX-3000003

TMRX-3000001

TMRT-3003243

TMRT-3003241

TMRX-3000005

TMRG-3003244

Part Number

TABLE A
OUTSIDE SCREW AND YOKE GATE VALVE
PART NUMBERS

Ordering
Procedure
Contact your local distributor for availability. When placing an order, indicate the full product name and Part
Number (P/N). Refer to Table A for a
complete list of part numbers.

TFP1540
Page 6 of 6

GLOBAL HEADQUARTERS | 1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone +1-215-362-0700

Copyright 2013 Tyco Fire Products, LP. All rights reserved.