REAR FOG LAMP
REAR FOG LAMP
Wiring Diagram — R/FOG — To ESM
MKWA1529E
LT-1
REAR FOG LAMP
MKWA3080E
LT-2
TURN SIGNAL AND HAZARD WARNING LAMPS
TURN SIGNAL AND HAZARD WARNING LAMPS
Wiring Diagram — TURN — To ESM
MKWA1444E
LT-3
TURN SIGNAL AND HAZARD WARNING LAMPS
MKWA3081E
LT-4
PARKING, LICENSE PLATE AND TAIL LAMPS
PARKING, LICENSE PLATE AND TAIL LAMPS
Wiring Diagram — TAIL/L — To ESM
MKWA1525E
LT-5
PARKING, LICENSE PLATE AND TAIL LAMPS
MKWA1441E
LT-6
PARKING, LICENSE PLATE AND TAIL LAMPS
MKWA3082E
LT-7
STOP LAMP
STOP LAMP
Wiring Diagram— STOP/L — To ESM
MKWA3083E
LT-8
BACK-UP LAMP
BACK-UP LAMP
Wiring Diagram — BACK/L — To ESM
MKWA1443E
LT-9
BACK-UP LAMP
MKWA3084E
LT-10
ILLUMINATION
ILLUMINATION
System Description To ESM
The illumination lamps operation is controlled by the lighting switch which built into the combination switch,
BCM and IPDM E/R.Tail lamp relay is built into IPDM E/R.BCM read combination switch condition. Refer to LT-
189, “System Description” on ESM.
Power is supplied at all times
● to tail lamp relay (located in the IPDM E/R).
Power is also supplied at all times
● to BCM terminals 74 and 79
● through 40A fusible link (letter J, located in the fuse and fusible link box).
With the ignition switch in the ON or START position, power is supplied
● to BCM terminal 24
● through 10A fuse [No. 4, located in the fuse block (J/B)].
● to power window main switch terminal 5
● to front power window switch (passenger side) terminal 1
● through BCM terminal 78
Ground is supplied
● to BCM terminals 2 and 70
● through grounds M19, and M20.
ILLUMINATION OPERATION BY LIGHTING SWITCH
When the lighting switch is turned to 1ST position, BCM read combination switch condition. Refer to LT-189,
“System Description” on ESM. And BCM send illumination lamp request signal to IPDM E/R via CAN commu-
nication line. Then IPDM E/R is turned on tail lamp relay. Tail lamp relay is energized and then power is sup-
plied:
● through terminal 15 of the IPDM E/R
● to heated seat switch driver side (illumination) terminal 5
● to heated seat switch passenger side (illumination) terminal 5
● through terminal 16 of the IPDM E/R
● to audio unit terminal 36
● to audio and navi control unit terminal 36
● to heater control panel terminal 15
● to A/C auto amplifier terminal 11
● to headlamp aiming switch terminal 3
● to headlamp washer switch terminal 3
● to hazard switch terminal 3
● to ashtray illumination terminal 1 and
● to A/T device terminal 5
● to ESP OFF switch terminal 3
Ground is supplied at all times
● to heated seat switch driver side terminal 6
● to heated seat switch passenger side terminal 6
● through body grounds B17, B23, B44 and B51
● to heater control panel terminal 7
● to A/C auto amplifier terminal 12
● to headlamp aiming switch terminal 4
● to headlamp washer switch terminal 4
● to hazard switch terminal 4
● to ashtray illumination terminal 2
● to A/T device terminal 4
LT-11
ILLUMINATION
● to power window main switch terminal 7
● to front power window switch (passenger side) terminal 7
● to ESP OFF switch terminal 4
● through body grounds M19 and M20
● to audio unit terminal 36
● to audio and navi control unit terminal 36
● through body ground M60
With power and ground supplied, illumination lamps illuminate.
COMBINATION SWITCH READING FUNCTION
Refer to LT-189, “System Description” on ESM.
LT-12
ILLUMINATION
Schematic To ESM
MKWA3086E
LT-13
ILLUMINATION
Wiring Diagram — ILL — To ESM
MKWA1530E
LT-14
ILLUMINATION
MKWA3088E
LT-15
ILLUMINATION
MKWA1748E
LT-16
ILLUMINATION
MKWA3089E
LT-17
ILLUMINATION
MKWA1531E
LT-18
ILLUMINATION
MKWA1759E
LT-19
ILLUMINATION
MKWA3296E
LT-20
