Environment

I N F O R M A T I O N F R O M K O D A K J-300 $10.00

Environmental Guidelines for

Amateur Photographers
Kodaks health, safety,

and environmental

publications are available

to help you manage your

photographic processing

operations in a safe,

environmentally sound

and cost-effective

manner. This publication

will help amateur

As a photographer, you have a photographers know

photographer and charge for your
unique sensitivity to the environ- services, you are required by law to
ment around you. But, as an comply with certain environmental
how to safely handle
amateur photographer, you dont and workplace safety regulations
have to worry about the (some of which are covered in this and dispose of
environmental and safety publication). As an amateur
regulations that apply to photographer, you are not required photographic
commercial businesses and by law to follow those regulations
professional photographers. but we are providing processing chemicals.
But you still need to know how to recommendations on safe handling
safely handle and dispose of and waste management practices.
photographic processing chemicals.

SAFETY
AMATEUR OR
PROFESSIONAL? Chemicals are safe when handled
properlythats why its important
An amateur is someone who to know and understand the
engages in an activity as a pastime chemicals youre working with and
rather than a profession. An the appropriate protective measures
amateur photographer does not you should use when handling
generate (or try to generate) revenue them.
from the use of photography. When
you become a professional

Eastman Kodak Company, 2008

 Exhaust the room air from the Component Information:
PERSONAL PROTECTIVE processing chemical area to the identifying what ingredients are
EQUIPMENT outdoors at a minimum rate of in the product.
10 room volumes per hour1 If you Hazard Identification: hazardous
When working with photographic have a fresh-air supply duct to components in the product and
processing chemicals, you should your darkroom, set your exhaust safe handling information.
wear protective clothing to ensure rate slightly higher than the
your safety. Whenever the potential supply rate. This produces a slight First Aid Measures: appropriate
exists for chemicals to get in your negative pressure and reduces the emergency procedures and other
chance of vapors or gases information.
eyes, wear safety glasses with side
shields. When mixing chemicals, escaping to an adjoining room. Fire-Fighting Measures.
wear tight-fitting goggles. Wear To determine how much exhaust Precautions to take if a spill
impervious gloves, such as those per hour is required for your occurs.
made with Neoprene or Nitrile, to darkroom: Handling and Storage: special
prevent contact with skin. You Determine room volume personal precautionary measures
should also wear an apron, or other (h x l x w) and storage information.
protective clothing that is Multiply by 10 Exposure and Personal
impervious to chemicals, to prevent Protection: ventilation and what
Divide by 60 minutes
chemicals from coming in contact personal protective equipment is
with your clothing. Most darkrooms are 10 h x 10 l x needed, such as gloves, goggles,
8 w which equals 800 cubic etc.
feet (ft3). Therefore,
VENTILATION Physical and Chemical Properties:
such as pH, color, and odor.
Exhaust rate of
Some Kodak photographic 800 ft3 x 10 133 ft3 min for Stability and Reactivity:
processing solutions may release x 10 = 10 room incompatibility with other
60 min/hr chemicals.
vapors or gases that can irritate the changes
eyes and respiratory tract and have per hour Health Information: such as
unpleasant odors. When processing symptoms of overexposure.
solutions are warm, they may Disposal Information: waste
generate more vapors. In addition, MATERIAL SAFETY DATA management options for the
temperature affects processing SHEETS product.
times. Therefore, it is important that A Material Safety Data Sheet
you work with solutions at the (MSDS) is available for every Kodak
proper temperatures. For your own OBTAINING MSDSs
chemical you purchase. The MSDS
personal comfort and good health tells you how to use, handle, and To get a copy of a MSDS for a Kodak
practices, you should minimize the store the product safely. The content product, see your dealer or retail
concentration of these chemicals by of MSDSs varies from one product store, or visit Kodak on-line at
controlling ventilation. We to the next. Among the topics www.kodak.com/go/msds.
recommend using a room with a covered are:
source of fresh air for darkroom use. Product Information: identifying
Here are some ventilation the name of the product and any
guidelines for manual sink-line or other trade names.
open tray processing areas:
Supply tempered fresh air to the
darkroom above the processing
solutions. Position the supply of 1. For 10 x 10 x 10-foot room
fresh air so that it will not affect
the capture of vapors or gases by
the exhaust opening.

2 Environmental Guidelines for Amateur Photographers J-300

 MANAGING WASTE REDUCING WASTE PHOTOGRAPHIC
EFFLUENT
There are two types of wastesolid The best way to help the
wastes and processing effluent. Most environmentand yourselfis to Before you can decide how to
solid wastes are packaging use photographic processing dispose of photographic processing
materials. The waste produced from solutions efficiently. You can chemicals, you need to know what
processing photographic films and accomplish this by: type of waste disposal system you
papers is called photographic Buying only the supplies you have. The type of system you have
effluent; it includes developer, fixer, need. This way, you wont be and the types of materials you need
bleaches, and wash water. There are storing unused photoprocessing to dispose of will determine how
many different ways to manage chemicals past their you dispose of your waste. There are
recommended shelf life and later, two types of waste disposal
solid and effluent waste materials.
having to dispose of them. systemssewer and septic.
Mixing only the amount of
photographic processing
chemicals you need; this way, you
wont have to dispose of
additional materials.

Amateur or Professional?

You are likely a business selling

some or all of your work and
No
Are you an amateur photographer therefore are covered by additional
Start
who does not sell your work? requirements. See More
Information at the back of this
publication.

Yes

If you process work at a school,

Do you have a darkroom at home No studio, or other business, disposal
where you process films and responsibility falls on the business
papers? owner. See More Information at the
back of this publication.

Yes

You are likely using a septic system

for disposal of wastewater. Certain No
Are you using a sewer for disposal of
materials should not be sent to the
your wastewater?
septic system. See Septic Systems
for more details.

Yes

Most common photographic

chemicals may be safely disposed to
the sewer. See Sewer Systems for
more details.

Environmental Guidelines for Amateur Photographers J-300 3

 and state regulatory limits Developers
SEWER SYSTEMS established under the Clean Water Stop baths
Act. In order to comply, the local
The majority of wastewater Fixers (after silver recovery)
POTW must establish pretreatment
generated in our communities Wash waters
guidelines (commonly referred to as
travels through the sewer system to
sewer codes) that impact businesses. Do NOT send:
a Publicly Owned Treatment Works
As a domestic useran amateur Selenium toners
(POTW). The POTW is responsible
photographeryou are excluded
for treating the wastewater that Solvents
from these regulations. Most
comes through its facility. The water Other materials that are
photographic chemicals can be sent
that leaves the POTW after prohibited, i.e., flammable
to the sewer. They include:
treatment must comply with federal materials

Your House

City Disposal

Trash
Bin

Sewer

POTW

H O
2

4 Environmental Guidelines for Amateur Photographers J-300

 WASTE MANAGEMENT SEPTIC SYSTEMS WASTE MANAGEMENT
OPTIONS ALTERNATIVES FOR
Septic tank systems are designed SEPTIC SYSTEMS
If you are on a sewer system, the best and used for the disposal of
wayand the most appropriateis to domestic waste, primarily in areas Kodak does not recommend the use of
dispose of your photographic processing where municipal sewers are septic systems for disposal of
effluent through the sewer system. Most unavailable. They operate with photographic processing chemicals
photographic processing solutions anaerobic (without oxygen) because the disposal of
are biodegradable and are effectively biological action to treat the wastes photographic processing solutions
treated when discharged to POTWs. discharged. This also includes leach may affect the proper operation of
POTWs that have secondary fields and cesspools. the septic system. Other disposal
(biological) wastewater treatment can Septic systems do not have the options are available for septic
effectively treat the waste stream ability to properly treat system users, including household
through the use of biological action, photographic processing solution waste collection facilities, discharge
such as bacteria nutrients and waste. Regulations have been to a nearby municipal treatment
aeration, to break down the waste it established by the United States plant, or a licensed hazardous waste
receives so that it may be safely Environmental Protection Agency hauler. Table I provides a summary
discharged to a body of water. (USEPA) and many states to of waste management options
Photographic processing effluent minimize the potential of adversely which are available for Kodak
includes developer, fixer, bleach, and affecting sources of underground products.
wash water involved in processing drinking water. Although these
films and papers. Two key regulations typically do not impact
characteristics of photoprocessing domestic users, such as amateur
effluent are pH and the concentration photographers, we recommend that
of silver. Developer has a high pH you contact your local health
and is therefore alkaline or caustic. department to determine whether
Fixer has a low pH and is therefore discharging photographic
acidic. When fixer and developer are processing effluents into your septic
combined as the total process system is appropriate for your
effluent, the effluent is neutralized, location.
resulting in a better compatibility
Table I. General Guidelines
with drain pipes and treatment at the
POTW. Sewer
Other
Another key characteristic of System
Alternatives
Options
photoprocessing effluent is the silver
concentration found in photographic KODAK Products Household
Discharge Discharge
fixer or bleach-fix effluent. Although Hazardous Trash
to Sewer to nearby
the form of silver (silver thiosulfate) (POTW)
Waste
POTW
Disposal
found in photographic processing Collection
effluent is not harmful and is Developer

removed during secondary treatment unused/used
at the POTW, it is a good practice to
Fixer/Bleach-Fix
recover silver before discharging the unused
effluent. See page 6 for information
on silver recovery. used * *
If you do not want to recover silver Stabilizers
from used photographic fixer or
Sepia Toner
bleach-fix, you may choose to utilize
other disposal options, such as Rapid Selenium Toner
household hazardous waste Indicator Stop Bath
collection. Refer to the section on
PHOTO-FLO Solution
Waste Management Alternatives for
Septic Systems for additional * Recommended after silver recovery is performed.
Recommended after neutralization.
information.

Environmental Guidelines for Amateur Photographers J-300 5

 Most communities have local
household hazardous waste DISPOSAL OF OTHER SILVER RECOVERY
collection facilities. These facilities KODAK PRODUCTS
You can find silver in a number of
are available to the public to collect
Used KODAK Rapid Selenium Toner different materials when you
items from domestic use that should
is regulated as a hazardous waste process photographic materials. The
not be disposed of through
under the USEPA Resource original source of silver is
municipal trash, septic, or sewer
Conservation and Recovery Act photographic films and papers.
systems. This option is available if
(RCRA) regulations for commercial Once processed, silver can be
you generate less than 220 pounds
users. We recommend that domestic retained in the photographic
(100 kilograms) of hazardous waste
users do not discharge this material material or transferred to solutions
per calendar month. Most home
to the sewer or discard it in the used to process the photographic
hobbyist photographers fall well
municipal trash. Use a household materials. Commercial business and
below this limit.
hazardous waste collection facility or photographers must recover silver
You can also discharge your
a licensed hazardous waste hauler to from photoprocessing effluent to
photographic wastes to a local
manage this material. meet sewer discharge limits
municipal sewer authority, often
KODAK Indicator Stop Bath established by POTWs. Amateur
referred to as a Publicly Owned
contains acetic acid. It has a very low photographers are not required to
Treatment Works (POTW). Contact
pH (1.0). Neutralize this solution recover silver. But whether you are a
the POTW directly to see if they will
with sodium bicarbonate (baking professional or amateur
accept your waste.
soda) solution prior to sending the photographer, silver recovery
The third option available is to
material to the sewer. This will help provides environmental benefits,
contract with a licensed hazardous
protect your drain pipes. Add the conserves a natural resource, and
waste hauler to manage your
sodium bicarbonate slowly to the may provide a source of revenue.
photographic processing wastes for
solution because it will cause The amount of silver found in
off-site disposal. You may check the
foaming. Neutralize the solution in a photoprocessing effluent will
yellow pages of your local phone
well ventilated area using proper depend upon the amount of film or
book for a list of waste management
personal protective equipment paper youve processed. See Table II
companies in your area. (There is a
(gloves, goggles, and apron). for typical silver concentrations. For
fee for this service.) If you do not want to neutralize the small volume users like amateur
Indicator Stop Bath prior to disposal, photographers, metallic replace-
MUNICIPAL TRASH you may choose to utilize other ment is usually a good method for
DISPOSAL disposal options, such as household recovering silver from photographic
hazardous waste collection. Refer to processing effluent. In this method,
We do not recommend that you dispose the previous section on Waste iron metal (steel wool) reacts with
of used or unused photographic Management Alternatives for Septic the silver in the fixer solution. The
processing solution in your regular Systems for additional information. iron replaces the silver in solution,
trash. This is to ensure the safety of while the less active metal (silver)
the trash collectors who would not settles out as a solid sludge. To bring
know that this material is in the trash
DISCONTINUED KODAK the silver in contact with the iron,
and could possibly come into contact
PRODUCTS the used fixer passes through the
with it. container filled with steel wool. The
For information on managing
steel wool provides the source of
discontinued Kodak products, please
iron to replace the silver.
contact Kodak at 1-800-242-2424 or
email kes@kodak.com for assistance.

Table II. Silver Concentrates Found in Photoprocessing Solutions

Solution Amount
Developer Contains negligible amounts of silver
Fixer/Bleach-Fix 30005000 milligrams/litre
Wash Water/Stabilizer 15 milligrams/litre

6 Environmental Guidelines for Amateur Photographers J-300

 The advantages to using metallic
replacement cartridges are the low TIPS FOR RECOVERING REFINING
initial cost (approximately $50 each), SILVER
After the metallic replacement
and the simplicity of installing cartridge is exhausted, you have to
To use metallic replacement
themall you have to do are a few send it to a refiner to reclaim the
cartridges as efficiently as possible,
simple plumbing connections. The silver that is present in the form of a
fill them with water before you use
disadvantage of metallic sludge in the cartridge. For a list of
them. This will allow the solution to
replacement is that the silver is refiners, visit www.kodak.com/go/
come into contact with the greatest
recovered as a sludge, which makes kes.
surface area of steel wool and
it more difficult to determine the
prevent channeling. Regardless of
exact amount of silver recovered
the amount of effluent passed
and requires more costly refining.
through it, never use a cartridge for
SOLID WASTE
Also, you cannot reuse cartridges;
more than six months. The cartridge
you must replace them when they You can choose from several options
is used to remove silver from the
become exhausted. For small- for managing the solid waste
fixer/bleach fix solution only. Do
volume users, such as amateur associated with processing Kodak
not add developer or any other
photographers, metallic films and papers. Refer to Table III
chemical to the cartridge. Adding
replacement cartridges usually last for guidelines on what to do with
developer or other chemicals will
about six months. these materials.
destroy the cartridge and inhibit the
You can recover silver from small
silver-recovery process.
batches of fixer by pouring the
solution into a metallic replacement
cartridge. You can use the KODAK
Chemical Recovery Cartridge,
Junior Model II.

Table III. General Guidelines

Product Component Material Option

Film Carton/Box 100% recycled fiberboard Discard in regular trash

35 mm Body 2 Plastic* Recycle

Canister
Cap 4 Plastic* Discard in regular trash

35 mm magazine Steel Recycle

35/120/220 spool 7 Plastic* Recycle

126/110 cartridge 7 Plastic* Recycle

Film Emulsion, base Discard in regular trash

Paper Carton/Box 100% recycled fiberboard Discard in regular trash

Core Fiberboard Recycle

Photochemical Container Bottles 2 Plastic* or glass Recycle**

Caps 5 Plastic* Discard in regular trash

Carton 100% recycled fiberboard Recycle or

Discard in regular trash

* Refer to Appendix A for resin codes and descriptions. Check with your community recycling program for details or ask your
Check with your community recycling program for details or local photographic processing lab if they participate in the
ask your local photographic processing lab if they participate KODAK Paper Core Recycling Program.
in the KODAK Film Container Recycling Program. ** Refer to Appendix B for information on photochemical bottle
recycling in community recycling programs.

Environmental Guidelines for Amateur Photographers J-300 7

 APPENDIX A
Resin Codes
Today, plastics are among the easiest types of waste to recycle. Responding to requests from recyclers, the Society
of the Plastics Industry, Inc. created the following codes to identify plastic packaging by resin types. These codes
are typically imbedded in the bottoms of plastic bottles or containers and allow easy
sorting of plastic waste.

Code Resin Type Examples

1 PETEPolyethylene terephthalate Beverage containers, boil-in food pouches, processed meat packages

Film trays, chemical bottles, plastic lids for anesthetics

2 HDPEHigh-density polyethylene and many other products, barrier envelopes, milk bottles, detergent
bottles, oil bottles, toys, plastic bags

Film packet outer wraps, food wrap, vegetable oil bottles, blister
VVinyl (PVC or polyvinyl chloride)
3 packaging

LDPELow-density polyethylene Shrink-wrap, plastic bags, garment bags

4

Margarine and yogurt containers, caps for containers,

PPPolypropylene
5 some wraps

PSPolystyrene Egg cartons, fast food trays, disposable plastic silverware

6

OTHEROther types Multi-resin containers

7

8
J-300 J-300
 Q. What type of plastic are the containers made from?
APPENDIX B
A. Most of the plastic Kodak photochemical
Recycling KODAK Photochemical Containers containers are manufactured from high density
polyethylene, the Society of Plastics Industry (SPI)
PREPARING KODAK PHOTOCHEMICAL code number 2 or low-density polyethylene, SPI
CONTAINERS FOR RECYCLING code number 4. In addition, some Kodak plastic
containers are made of other resins and are coded
You can help minimize solid waste by participating in number 7 to symbolize layered multi-material
your local community recycling program. The plastics.
following information will help you in preparing
empty plastic or glass Kodak photochemical containers Q. What is an SPI code and where will I find it?
for recycling in your local recycling program:
A. An SPI code is a way to identify what type of
1. Follow the recommendations for personal plastic the container is made from. The number
protection and ventilation, as described in the will be located on the bottom of the chemical
product Material Safety Data Sheet (MSDS), while bottle, inside the chasing arrows (mobius loop).
rinsing the empty container. For Cubitainers, the SPI code will be located near
2. Empty the container of all residual product, and the neck of the container.
dispose of the residual in accordance with all local,
state, and federal regulations. Q. What SPI code numbers will the recycler accept?
3. To minimize splattering and respiratory exposure, A. You will need to contact your local recycler for the
slowly rinse caps and empty containers with cold information on what recyclable plastics they
water. In some instances, the chemical residue may accept. Each recycler may have different market
react with water if present in high concentrations. outlets for the plastics which determine what
Dispose of the rinsate (rinse water) in accordance recyclables they can collect.
with all local, state, and federal regulations.
4. Repeat the rinsing of the containers two more Q. How do I contact my local recycler?
times; you can use warm water (approximately
A. Call your local or state recycling coordinator,
100 F) for the final rinse to increase the solubility
municipal waste collection agency, or your local
of any remaining chemicals.
waste disposal company. If these agencies cannot
5. Once you no longer need the caps, rinse and assist you, you can call the American Plastics
discard them. Do not place them in the recycling Council (APC) at 1-800-243-5790 for information
container. on plastic recyclers in your area.
6. If the containers have visible stains or residue after
triple rinsing, do not recycle them. Dispose of Q. What information will I have to provide to the recycler
them in accordance with local regulations. when inquiring about recycling my containers?
7. If the rinsed container is plastic, slit it so it cannot A. It would be helpful for the recycler if you provided
be used again and place it into your recycling a sample of the rinsed containers that you would
collection container. like to recycle; a count of how many containers
Answers to some frequently asked questions about you generate per week, month, or year; the
recycling Kodak photochemical containers: Material Safety Data Sheets for the photochemical
product that was sold in the original container;
Q. Does Kodak accept back the empty plastic or glass
and a copy of this Appendix. You may be asked to
photochemical containers?
sign a form stating you will make sure the
A. Kodak does not accept back the empty plastic or containers have been properly rinsed before you
glass photochemical containers. Local recyclers are send them to the recycler.
best equipped to recycle these containers.

Environmental Guidelines for Amateur Photographers J-300 9

Q. Why do some local recyclers not accept the containers? The recycling information in this publication applies to
empty Kodak plastic or glass containers used for the
A. Some recyclers may not understand the nature of
following Kodak photochemical products only and is
the contents of the containers. Most Kodak not intended for containers that were reused for other
photographic chemicals are water soluble. purposes.
Properly rinsed photochemical containers with no
visible stains or residue are expected to pose no KODAK EKTACOLOR PRIME Chemicals
greater health concerns for customers or recyclers
than properly rinsed household chemical KODAK EKTACOLOR PRIME Developer
containers. Some recyclers may only be able to Replenisher / RA-4
process specific sizes of containers, types of KODAK EKTACOLOR PRIME Developer
materials (plastic and glass), and colors of glass at Regenerator
their facility. As a result, they may not be able to KODAK EKTACOLOR PRIME Bleach-Fix and
accept every container that you would like to Replenisher
recycle.
KODAK EKTACOLOR PRIME Stabilizer and
Replenisher / RA-4
Q. Can I recycle the 30- and 55-gallon Kodak plastic drums
that my photographic chemicals are shipped in? KODAK EKTACOLOR RA Chemicals
A. Yes, this is possible provided you have located a KODAK EKTACOLOR RA Developer Starter
recycler of such drums in your area. However,
KODAK EKTACOLOR RA Developer Replenisher
these drums are part of the KODAK Returnable
RT, Part A
Drum Program and can be sent to the Kodak-
approved drum reconditioner, then back to Kodak KODAK EKTACOLOR RA Developer Replenisher
for reuse. If you need further information about RT, Part B
the KODAK Returnable Drum Program, call KODAK EKTACOLOR RA Developer Replenisher
Kodak at 1-800-242-2424. RT, Part C
KODAK EKTACOLOR RA Developer Replenisher
Q. Whom may I contact at Kodak for additional
KODAK EKTACOLOR RA 100 Developer
information about the recycling of Kodak photochemical
Replenisher
containers?
KODAK EKTACOLOR RA 100 Developer
A. For additional information, you may contact the Regenerator
Kodak Information Center at 1-800-242-2424,
Monday through Friday, from 9 a.m. until 7 p.m. KODAK EKTACOLOR RA 100 Developer
(Eastern time). Regenerator (WS)
KODAK EKTACOLOR RA Bleach-Fix and
Replenisher
KODAK EKTACOLOR RA 100 Bleach-Fix
Replenisher
KODAK EKTACOLOR RA Stabilizer and
Replenisher / EP-2, RA-4
KODAK FLEXICOLOR Chemicals
KODAK FLEXICOLOR Developer Starter LORR
KODAK FLEXICOLOR Developer Replenisher
LORR
KODAK FLEXICOLOR Developer Replenisher
LORR, Part A
KODAK FLEXICOLOR Developer Replenisher
LORR, Part B
KODAK FLEXICOLOR Developer Replenisher
LORR, Part C
KODAK FLEXICOLOR Bleach III / C-41, Part A
KODAK FLEXICOLOR Bleach III / C-41, Part B
KODAK FLEXICOLOR Bleach III Starter
10 Environmental Guidelines for Amateur Photographers J-300
 KODAK FLEXICOLOR Bleach III Replenisher, KODAK EKTACHROME R-3 Chemicals
Part A
KODAK EKTACHROME R-3 First Developer
KODAK FLEXICOLOR Bleach III Replenisher, Replenisher
Part B
KODAK EKTACHROME R-3 Color Developer
KODAK FLEXICOLOR Bleach III Regenerator Replenisher, Part A
KODAK FLEXICOLOR RA Bleach Replenisher NR KODAK EKTACHROME R-3 Color Developer
KODAK FLEXICOLOR Bleach III NR Replenisher Replenisher, Part B
KODAK FLEXICOLOR RA Fixer and Replenisher KODAK EKTACHROME R-3 Color Developer
Replenisher, Part C
KODAK FLEXICOLOR Fixer and Replenisher
KODAK EKTACHROME R-3 Bleach-Fix and
KODAK FLEXICOLOR Stabilizer and
Replenisher
Replenisher LF
KODAK EKTACHROME R-3 First Developer and
KODAK Chemicals for Process E-6 Color Developer Starter
KODAK First Developer, Process E-6 KODAK EKTACHROME R-3000 Chemicals
KODAK First Developer Replenisher, Process E-6
KODAK EKTACHROME R-3000 First Developer
and Process E-6AR
KODAK EKTACHROME R-3000 Color Developer,
KODAK First Developer Starter, Process E-6
Part A
KODAK Reversal Bath, Process E-6
KODAK EKTACHROME R-3000 Color Developer,
KODAK Reversal Bath and Replenisher, Process Part B
E-6 and Process E-6AR
KODAK EKTACHROME R-3000 Color Developer,
KODAK Color Developer, Process E-6, Part A Part C
KODAK Color Developer, Process E-6, Part B KODAK EKTACHROME R-3000 Bleach-Fix
KODAK Color Developer Replenisher, Process E-6
KODAK Color Developer Starter, Process E-6
KODAK Bleach, Process E-6
KODAK Bleach Starter, Process E-6
KODAK Fixer, Process E-6
KODAK Fixer and Replenisher, Process E-6 and
Process E-6AR
KODAK Defoamer, Process E-6
KODAK Pre-Bleach, Process E-6
KODAK Pre-Bleach and Replenisher, Process E-6
and Process E-6AR
KODAK Final Rinse, Process E-6
KODAK Final Rinse and Replenisher, Process E-6

Environmental Guidelines for Amateur Photographers J-300 11

 The following publications are available from
MORE INFORMATION Kodak Customer Service or from dealers who sell
Kodak products.

For more information about

Kodak Environmental Services, www.kodak.com/go/kes J-210 Sources of Silver in Photographic
visit Kodak online at Processing Facilities
For environmental or safety J-211 Measuring Silver in Photographic
800-242-2424
questions about Kodak products, Processing Facilities
services, or publications, call
J-212 The Technology of Silver Recovery for
For questions about the safe Photographic Processing Facilities
handling of photographic
J-213 Refining Silver Recovered from
chemicals or health-related
1-585-722-5151 Photographic Processing Facilities
information about Kodak
products, call our 24-hour hotline J-214 The Regulation of Silver in Photographic
at Processing Facilities
For questions concerning the safe J-215 Recovering Silver from Photographic
transportation of Kodak products, Processing Facilities
1-585-722-2400
call Kodak Transportation
Services at J-216 The Fate and Effects of Silver in the
Environment
If you have questions about Kodak products, call Kodak.
J-217 Using Code of Management Practice to
In the U.S.A., call 1-800-242-2424, Ext. 19, Manage Silver in Photographic Processing
MondayFriday Facilities
9 a.m.7 p.m.
(Eastern time)
In Canada, call 1-800-465-6325,
MondayFriday
8 a.m.5 p.m.
(Eastern time)
In countries other than the U.S. contact your local Kodak
and Canada, representative, or your
usual supplier of Kodak
products.

This publication is printed on recycled paper that contains

50 percent recycled fiber and 10 percent post-consumer material.

EASTMAN KODAK COMPANY ROCHESTER, NY 14650

Environmental Guidelines for Amateur Photographers

KODAK Publication No. J-300 Kodak , "e" mark, Ektachrome, Ektacolor, Flexicolor, Photo-Flo,
CAT No. 851 8755 and Prime are trademarks. Revised 7-08
Printed in U.S.A.