NUMERO DE TARJETA
TASK NUMBER
TASK CARD 1 de 2
DESCRIPCION DE LA TARJETA TITULO JACK AIRPLANE AXLES
TASK DESCRIPTION TITLE
REFERENCIAS HRS HOMBRE SISTEMA ATA ZONA APLICABILIDAD
REFERENCES MANHOURS N/A ATA / SYSTEM 32 ZONE STA. 92.92 APPLICABILITY BOEING 737-201
07 11 31 CODIGO MATRICULA DEL AVION N/S DEL AVION TRABAJO
AIRCRAFT REGISTRATION AIRCRAFT S/N BOEING 737 - 201 JAA
CODE ALPHA JOB
MODELO DEL MOTOR N/S DEL MOTOR POS MOTOR
ENGINE MODEL JT8D TURBOFAN ENGINE S/N 21640 ENGINE POS DUAL WINGS LOW
MATERIAL HERRAMIENTA
MATERIAL TOOLING
Axle Jacks and Jacking Adapters. Tool box. PPE.
ITEM DESCRIPTION MECH INSP
1 A. Jacking points are provided under each landing gear axle to remove
wheel and tire or brake assembly without raising the entire airplane. For
approximate axle jack pad heights and clearances between tires refer to
7-11-11, Fig. 202. The tables should be used as a guide only, as
dimensions vary due to conditions.
CAUTION: DO NOT ATTEMPT TO JACK AIRPLANE BY PLACING JACK
UNDER ANY PART OF THE LANDING GEAR OTHER THAN THE AXLE JACK
PADS. DAMAGE RESULTING FROM JACKING ELSEWHERE MAY RESULT IN
LANDING GEAR FAILURE.
2 Jack Main Landing Gear Axles.
A. When both tires on the same main gear axle are flat, check that all
landing gear downlocks are installed and raise the airplane with
minimum height jacks. Refer to 7-11-11, Fig. 202, for jacks of suitable
heights.
B. If both tires on the same main gear axle are flat and suitable jacks are
not available, it will be necessary to raise the axle initially by another
means. The airplane may be raised as follows:
(1) By reinflating the tires. At least one tire must be in good shape and
well seated on its wheel. A source of high pressure air, such as air
bottles, must be available. Refer to 12-15-51 for tire inflation.
WARNING: ALWAYS USE A PRESSURE REGULATOR ON HIGH PRESSURE
AIR OURCE WHEN INFLATING TIRES. DO NOT INFLATE TIRES ABOVE
THEIR STRUCTURAL LIMITATIONS.
FECHA DE CUMPLIMIENTO 1/25/2017 ESTACION UNAQ
DATE OF CUMPLIANCE STATION
NUMERO DE TARJETA
TASK NUMBER
TASK CARD 2 de 2
DESCRIPCION DE LA TARJETA TITULO JACK AIRPLANE AXLES
TASK DESCRIPTION TITLE
REFERENCIAS HRS HOMBRE SISTEMA ATA ZONA APLICABILIDAD
REFERENCES MANHOURS N/A ATA / SYSTEM 32 ZONE STA. 92.92 APPLICABILITY BOEING 737-201
07 11 31 CODIGO MATRICULA DEL AVION N/S DEL AVION TRABAJO
AIRCRAFT REGISTRATION AIRCRAFT S/N BOEING 737 - 201 JAA
CODE ALPHA JOB
MODELO DEL MOTOR N/S DEL MOTOR POS MOTOR
ENGINE MODEL JT8D TURBOFAN ENGINE S/N 21640 ENGINE POS DUAL WINGS LOW
MATERIAL HERRAMIENTA
MATERIAL TOOLING
Axle Jacks and Jacking Adapters. Tool box. PPE.
ITEM DESCRIPTION MECH INSP
(2) By pushing or pulling the airplane so that the main gear is moved up
an inclined block. The slope is not important except from the viewpoint
of increased tow-bar load. The block should level out at a minimum
height of 4 inches (assuming a jack with a collapsed height of 10 inches).
If one block is used under each wheel there should be sufficient
clearance between them to permit insertion of the axle jack base.
C. For one flat tire a procedure similar to those adapted in A may be
applied. If an axle jack cannot be inserted at once an inclined block may
be used. In using an inclined block, however, the block should be made
of sufficient height to make subsequent use of an axle jack unnecessary.
The good wheel would be run up inclined block.
FECHA DE CUMPLIMIENTO 1/25/2017 ESTACION UNAQ
DATE OF CUMPLIANCE STATION
