8-Port Antenna R1 Y1 Y2 Y3

Frequency Range 698960 17102690 17102690 17102690

Dual Polarization X X X X
HPBW 65 65 65 65
Adjust. Electr. DT 1.510 2.512 2.512 2.512
set by

8-Port Antenna 698960/17102690/17102690/17102690 65/65/65/65 17/17.5/18/17.5dBi

1.510/2.512/2.512/2.512T
Type No. 80010872
Lowband R1, connector 1 2
698 960
Frequency Range MHz 698 806 791 862 824 894 880 960
Gain at mid Tilt dBi 16.3 16.8 17.0 17.3
Gain over all Tilts dBi 16.3 0.4 16.8 0.3 17.0 0.4 17.3 0.2
Horizontal Pattern:
Azimuth Beamwidth 70 1.7 68 1.7 68 1.8 66 1.7
Front-to-Back Ratio, dB > 23 > 24 > 25 > 26
Total Power, 30
Cross Polar Discrimination dB > 7.5 > 7.5 > 8.0 > 7.5
over Sector
Azimuth Beam dB < 1.5 < 2.0 < 2.0 < 2.0
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth 8.6 0.6 7.9 0.4 7.6 0.5 7.1 0.4
Electrical Downtilt 1.5 10.0
continuously adjustable
Tilt Accuracy < 0.3 < 0.3 < 0.3 < 0.2
First Upper Side Lobe dB > 16 > 16 > 16 > 15
Suppression
Cross Polar Isolation dB > 30
Port to Port Isolation dB > 28 (R1 // Y1, Y2, Y3)
Max. Effective Power W 400 (at 50 C ambient temperature)
per Port
Max. Effective Power W 800 (at 50 C ambient temperature)
Port 12
Values based on NGMN-P-BASTA (version 9.6) requirements.
936.5295 ngmn 04.25.01.00 Subject to alteration.

All specifications are subject to change without notice. 80010872 Page 1 of 5

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
8-Port Antenna

Lower highband Y1, connector 3 4

1710 2690
Frequency Range MHz 1710 1880 1850 1990 1920 2170 2300 2400 2500 2690
Gain at mid Tilt dBi 17.1 17.5 17.5 17.3 17.8
Gain over all Tilts dBi 17.1 0.5 17.4 0.3 17.5 0.4 17.3 0.4 17.6 0.4
Horizontal Pattern:
Azimuth Beamwidth 65 3.9 62 2.8 62 3.2 61 6.6 63 5.4
Front-to-Back Ratio, dB > 24 > 24 > 24 > 21 > 23
Total Power, 30
Cross Polar Discrimination dB > 8.0 > 10.0 > 11.5 > 9.5 > 8.5
over Sector
Azimuth Beam dB < 1.5 < 2.0 < 2.0 < 2.5 < 2.0
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth 7.3 0.5 6.8 0.5 6.4 0.6 5.6 0.4 5.2 0.3
Electrical Downtilt 2.5 12.0
continuously adjustable
Tilt Accuracy < 0.3 < 0.3 < 0.4 < 0.4 < 0.3
First Upper Side Lobe dB > 15 > 15 > 15 > 14 > 14
Suppression
Cross Polar Isolation dB > 28
Port to Port Isolation > 28 (Y1 // R1)
dB > 30 (Y1 // Y2, Y3)
Max. Effective Power W 200 (at 50 C ambient temperature)
per Port
Max. Effective Power W 400 (at 50 C ambient temperature)
Port 34
Values based on NGMN-P-BASTA (version 9.6) requirements.

Upper highband Y2, connector 5 6

1710 2690
Frequency Range MHz 1710 1880 1850 1990 1920 2170 2300 2400 2500 2690
Gain at mid Tilt dBi 17.4 17.6 17.9 18.2 18.4
Gain over all Tilts dBi 17.4 0.4 17.6 0.2 17.8 0.4 18.1 0.3 18.2 0.5
Horizontal Pattern:
Azimuth Beamwidth 65 3.0 66 2.0 66 1.5 66 2.2 65 4.6
Front-to-Back Ratio, dB > 22 > 22 > 23 > 22 > 25
Total Power, 30
Cross Polar Discrimination dB > 11.0 > 14.0 > 14.5 > 11.5 > 9.5
over Sector
936.5295 ngmn 04.25.01.00 Subject to alteration.

Azimuth Beam dB < 1.5 < 1.0 < 0.5 < 1.0 < 2.5
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth 7.1 0.4 6.7 0.3 6.3 0.4 5.6 0.4 5.0 0.2
Electrical Downtilt 2.5 12.0
continuously adjustable
Tilt Accuracy < 0.3 < 0.3 < 0.3 < 0.4 < 0.3
First Upper Side Lobe dB > 18 > 24 > 23 > 19 > 21
Suppression
Cross Polar Isolation dB > 28
Port to Port Isolation > 28 (Y2 // R1)
dB > 30 (Y2 // Y1, Y3)
Max. Effective Power W 200 (at 50 C ambient temperature)
per Port
Max. Effective Power W 400 (at 50 C ambient temperature)
Port 56
Values based on NGMN-P-BASTA (version 9.6) requirements.

All specifications are subject to change without notice.

Page 2 of 5 80010872
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
 8-Port Antenna

Right side, upper highband Y3, connector 7 8

1710 2690
Frequency Range MHz 1710 1880 1850 1990 1920 2170 2300 2400 2500 2690
Gain at mid Tilt dBi 16.9 17.1 17.3 17.5 17.6
Gain over all Tilts dBi 16.9 0.3 17.1 0.3 17.3 0.4 17.4 0.2 17.4 0.5
Horizontal Pattern:
Azimuth Beamwidth 64 2.5 65 1.5 65 1.4 66 1.7 66 4.0
Front-to-Back Ratio, dB > 22 > 24 > 24 > 25 > 26
Total Power, 30
Cross Polar Discrimination dB > 10.0 > 14.5 > 14.5 > 11.5 > 9.0
over Sector
Azimuth Beam dB < 1.0 < 1.0 < 0.5 < 0.5 < 2.5
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth 7.2 0.4 6.7 0.4 6.3 0.5 5.6 0.4 5.0 0.2
Electrical Downtilt 2.5 12.0
continuously adjustable
Tilt Accuracy < 0.3 < 0.3 < 0.3 < 0.3 < 0.2
First Upper Side Lobe dB > 19 > 24 > 23 > 20 > 19
Suppression
Cross Polar Isolation dB > 28
Port to Port Isolation > 28 (Y3 // R1)
dB > 30 (Y3 // Y1, Y2)
Max. Effective Power W 200 (at 50 C ambient temperature)
per Port
Max. Effective Power W 400 (at 50 C ambient temperature)
Port 78
Values based on NGMN-P-BASTA (version 9.6) requirements.
936.5295 ngmn 04.25.01.00 Subject to alteration.

All specifications are subject to change without notice. 80010872 Page 3 of 5

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
8-Port Antenna

Electrical specifications, all systems Mechanical specifications

Impedance 50 Input 8 x 7-16 female long neck
VSWR < 1.5 Connector Position bottom
Return Loss dB > 14 Adjustment Mechanism FlexRET,
Interband Isolation dB > 28 continuously adjustable
Passive Intermodulation dBc < 150 (2 x 43 dBm carrier) Wind load N | lbf Frontal 1710 | 384
Polarization +45, 45 (at Rated Wind Lateral 560 | 126
Speed: 150 km/h) Rearside 1760 | 396
Max. Effective Power 900 (at 50 C ambient
W temperature) Max. Wind Velocity km/h 200
for the Antenna
mph 124
Values based on NGMN-P-BASTA (version 9.6) requirements.
Height / Width / Depth mm 2693 / 377 / 169
inches 106.0 / 14.8 / 6.7
Category of H (Heavy)
Mounting Hardware
Weight kg 42.0 / 44.2 (clamps incl.)
lb 92.6 / 97.4 (clamps incl.)
Packing Size mm 2896 / 397 / 212
inches 114.0 / 15.6 / 8.3
Scope of Supply Panel, FlexRET and
2 units of clamps
for 42 115 mm |
1.7 4.5 inches diameter

Accessories (order separately if required) 2)

3)
1)
Remarks Weight Units per
Type No. Description
mm | inches approx. kg | lb antenna

85010002 1 clamp Mast diameter: 110 220 | 4.3 8.7 2.7 | 6.0 2
85010003 1 clamp Mast diameter: 210 380 | 8.3 15.0 4.8 | 10.6 2
85010008 1 downtilt kit Downtilt angle: 0 8 4.3 | 9.5 1
86010154 Site Sharing Adapter 3-way (see figure below) 0.65 | 1.4
86010155 Site Sharing Adapter 6-way (see figure below) 1.35 | 3.0
86010162 Gender Adapter Solely to be used in combination with 0.045 | 0.099 1
86010163 Port Extender the FlexRET module 86010153V01 0.16 | 0.35 1
2693 | 106.0
2721 | 107.1
2761 | 108.7
Accessories (included in the scope of supply)
738546 1 clamp Mast diameter: 42 115 | 1.7 4.5 1.1 | 2.4 2
86010153V01 FlexRET 1
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
Wall mounting: No additional mounting kit needed.

Material: Reflector screen: Aluminum.

936.5295 ngmn 04.25.01.00 Subject to alteration.

Fiberglass housing: It covers totally the internal antenna components. The special
design reduces the sealing areas to a minimum and guarantees the best weather
protection. Fiberglass material guarantees optimum performance with regards to stability,
stiffness, UV resistance and painting. The color of the radome is light grey.
All nuts and bolts: Stainless steel or hot-dip galvanized steel.

Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are
DC grounded.

1) 9 | 0.4
Configuration example Configuration example 2) 72 | 2.8
with Site Sharing Adapter 86010154 with Site Sharing Adapter 86010155 3) 13 | 0.5
FlexRET FlexRET FlexRET FlexRET FlexRET FlexRET All dimensions
in mm | inches

Site Sharing Adapter Site Sharing Adapter

3-way 6-way
AISG AISG

BTS1 BTS2 BTS3

BTS1 BTS2 BTS3 BTS4 BTS5 BTS6

For more information please refer to the respective data sheets.

Page 4 of 5 80010872 All specifications are subject to change without notice.

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
 8-Port Antenna

Layout of interface:

Left Right

Y2 Y2
169 | 6.7 *

R1(L) 698 - 960

195 | 7.7 *

Top Y3(R) 1710 - 2690

Bottom Y1(L)/Y2(R) 1710 - 2690
6 5

Y1 Y1 R1 R1 Y3 Y3

104 | 4.1
4 3 2 1 8 7

54 | 2.1
124 | 4.9

224.5 | 8.8

325 | 12.8

377 | 14.8 *

Bottom view
* Dimensions refer to radome
All dimensions in mm | inches

Correlation Table
Frequency range Array Connector
936.5295 ngmn 04.25.01.00 Subject to alteration.

698 960 MHz R1 12

1710 2690 MHz Y1 34
1710 2690 MHz Y2 56 Y3
1710 2690 MHz Y3 78

Y1 Y2
R1
Left Right

Any previous data sheet issues have now become invalid.

All specifications are subject to change without notice. 80010872 Page 5 of 5

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
 Mounting Hardware
Clamp Included in the Scope of Supply

Suitable for mast diameter (mm) 42 115

[inches] [1.65 4.53]
Antenna mast distance (mm) 20 25
[inches] [0.79 0.98]
Material of clamp and screws Hot-dip galvanized steel / stainless steel
Weight (kg) 1.1
[lb] [2.43]

152 [5.98]

100 [3.94]

[0.790.98]
40 [1.57]
72 [2.83]

2025
40 [1.57]

15
21
4 4.53]
5
[1.6

M10 MA = 25 Nm

M8 MA = 20 Nm
35 [1.38]
64 [2.52]
125 [4.92]

2025
[0.790.98]
Subject to alteration.
936.3920/c

Please note: Kathrein does not recommend to use counter nuts. All dimensions in mm and [inches]
The additional nuts supplied are only meant as spares.

All specifications are subject to change without notice. 738546 Page 1 of 1

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
 FlexRET

A flexible, integrated solution for adjusting the electrical downtilt of Kathrein FlexRET antennas.

Compliant to AISG 1.1 and 3GPP/AISG 2.0 Daisy Chain feasibility

Single RETs or Multi RET displayed Pre-configurated

Type No. 86010153

Protocols compliant to AISG 1.1 and 3GPP/AISG 2.0
Logical interface ex factory 1) 3GPP/AISG 2.0
Operates as Single RETs or Multi RET
Ex factory Single RETs
Input voltage range V 10 ... 30 (pin 1, pin 6)
Power consumption W < 0.5 (stand by); < 10 (motor activated)
Connectors 2 x 8 pin connector according to IEC 60130-9; according to AISG
Daisy chain in: male; Daisy chain out: female
Hardware interfaces RS 485A/B (pin 5, pin 3);
power supply (pin 1, pin 6); DC return (pin 7);
according to AISG / 3GPP
Adjustment time sec 40
(full range) (typically, depending on antenna type)
Adjustment cycles > 50,000
Temperature range C 40 +60
Protection class IP 24 (installed)
Lightning protection AISG interface (each pin)
2.5 kA (10/350 s)
8 kA (8/20 s)
Housing material Profile: Aluminum anodized; cover: Aluminum die cast coated
Weight g 350
lb 0.77
Packing size mm 245 x 93 x 102
(H x W x D) inches 9.6 x 3.6 x 4
Dimensions mm 142 x 71 x 50.4
(H x W x D) inches 5.6 x 2.8 x 2
1)
The protocol of the logical interface can be switched from 3GPP/AISG 2.0 to AISG 1.1 with a vendor
specific command. Start-up operation of the FlexRET is only possible in a RET system supporting
3GPP/AISG 2.0!
1)
Please note:
If the Primary which controls the FlexRET system does not support the default ex-factory interface
setting, then the RCU must be switched to the appropriate standard of the Primary before installation.
Please contact Kathrein for further information.
If the FlexRET of an antenna has to be replaced, the FlexRET gets the information stored in the antenna
after power on automatically. It is not necessary to configurate the FlexRET manually.
Standards: EN 60950-1 (Safety)
EN 60950-22 (Safety Equipment installed outdoor)
EN 55022 (Emission)
EN 55024 (Immunity)
ETS 300019-1-4 (Environmental)
UL 60950-1; 1st edition
Certification: CE, FCC
Subject to alteration.

Scope of supply: FlexRET

Optional: Site Sharing Adapter (86010154 or 86010155) to create independent logial
interfaces at one antenna or site. Makes it possible to operate with more
than one independent Node B.
Please note:
In general, the addressing of the FlexRET is automatically performed. Only in case the FlexRET is
936.4643/b

manually addressed, the serial number has to be extended by the corresponding colour coding extension
(e.g. CSG351234-R1). The respective information can be found on the site documentation which is
included in the scope of supply.

All specifications are subject to change without notice. 86010153 Page 1 of 4

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
FlexRET

Startup of FlexRET
The FlexRET module included in the antenna is preconfigured with the following information:
Antenna model no., Antenna Serial no., Antenna configuration data. After connecting a control
cable and scanning the antenna line devices (ALD) the used primary (e.g. NodeB, ALC, etc.)
will find the FlexRET. You only need to insert your additional data.

Connecting the control cables:

Connect a control cable to the daisy chain input of the FlexRET. The tightening torque for fixing the
connector must be 0.5 1.0 Nm (hand-tightened).
The connector should be tightened by hand or by a special torque screw driver (order no.
85010080).
See also data sheet for Kathrein AISG-cable (86010007, ...).
Please note: To ensure the tightness of the RET System, Kathrein recommend the use of
Kathrein components only.
Please note: If the daisy chain output is not used, do not remove the protection cap.

For daisy chain operation, remove the protection cap and attach a control cable to interconnect
with the daisy chain input of the subsequent FlexRET or external RCU.
Please note: Do not remove the protection cap on the daisy chain output of the last FlexRET
or RCU device.
Subject to alteration.
936.4643/b

Page 2 of 4 86010153 All specifications are subject to change without notice.

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
 FCC Statements


'
!!!


*
,/%,1

(
+
$"%!(
,)
')
AE
$
)

'*!(4
%')$#
(
(* )
)$
)
$!!$,#
),$

$#)$#(3
9A:
(
+
".
#$)
*(
'"*!
#)''#2
#
9B:
)(
+
"*()
%)
#.

#)''#
'+2
#!*#
#)''#
))
".
*(
*#('
$%')$#4


*
,/%,+/

$)3
(
&*%"#)
(
#
)()
#
$*#
)$
$"%!.
,)
)
!")(
$'

!((

)!
+2

%*'(*#)
)$
%')
AE
$
)

*!(4
(
!")(
'
(#
)$
%'$+
'($#!
%'$))$#

#()
'"*!
#)''#
#

'(#)!
#()!!)$#4
(
&*%"#)
#')(2
*((
#
#

')
'$
'&*#.
#'.
#2

#$)
#()!!
#
*(
#
$'#
,)
)
#()'*)$#(2
".

*(
'"*!
#)''#
)$
'$
$""*#)$#(4
$,+'2
)'
(
#$
*'#)
))

#)''#
,!!
#$)
$*'
#

%')*!'
#()!!)$#4

)(
&*%"#)
$(
*(
'"*!

#)''#
)$
'$
$'
)!+($#
'%)$#2
,
#

)'"#
.
)*'##
)
&*%"#)
$

#
$#2
)
*('
(
#$*'
)$
)'.
)$
$'')
)
#)''#
.
$#
$'
"$'
$
)
$!!$,#

"(*'(3

8$'#)
$'
'!$)
)
'+#
#)##4

8 #'(
)
(%')$#
),#
)
&*%"#)
#
'+'4

8$##)
)
&*%"#)
#)$
#
$*)!)
$#

'*)
'#)
'$"
))
)$
,
)
'+'
(

$##)4

8$#(*!)
)
!'
$'
#
-%'#
'$6
)##
$'
!%4



&
!
0%,%.

(
+
$"%!(
,)
#*()'.
#
!#7-"%)

()#'9(:4
%')$#
(
(* )
)$

)
$!!$,#
),$
$#)$#(39A:
)(
+
".
#$)
*(
#)''#2
#
9B:
)(
+
"*()

%)
#.
#)''#2
#!*#
#)''#
))
".
*(
*#('
$%')$#
$
)
+4


%'(#)
%%'!
()
$#$'"
*-
 
= #*()'
#
%%!!(
*-
%%'!(
'$

-"%)(

!#4
=-%!$))$#
()
*)$'(
*-
*-
$#)$#(
(*+#)(
3
9A:
!=%%'!
#

$)
%(
%'$*'

'$*!!2
)
9B:
!=*)!()*'

!=%%'!
$)
%)'
)$*)
'$*!!

'$!)'&*
(*2
""
(
!
'$*!!
()
(*(%)!
=#
$"%'$"))'
!
$#)$##"#)4

Subject to alteration.

 &++.

(
!((

)!
%%')*(
$"%!(
,)
##
7@@C4

)
%%'!
#*"'&*

!
!((

()
$#$'"

!
#$'"
7@@C
*
#4

936.4643/b


*
,/%-,
(
!!!)

;#.<
#(
$'
"$)$#(
#$)
-%'((!.
%%'$+
.
)
%').
'(%$#(!
$'
$"%!#
$*!

+$
)
*('5(
*)$').
)$
$%')
)
&*%"#)4

All specifications are subject to change without notice. 86010153 Page 3 of 4

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
FCC Statements

Compliance Information Statement

(Declaration of Conformity Procedure)
Responsible Party: Kathrein USA

Address: Greenway Plaza II 2400 Lakeside Blvd. Suite 650

Richardson, Texas 75082

Telephone: (01+) 214.238.8800

Type of equipment:

Model Name: FlexRET

FCC ID SP3-86010153

Subject to alteration.
936.4643/b

All specifications are subject to change without notice.

Page 4 of 4 86010153 The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com