WASTEWATER DIVISION
FLORIDA BIOLINE THE WORLDS MOST ADVANCED
CONTINUOUS SELF-CLEANING, PRESSURE
DRIPLINE
COMPENSATING DRIPLINE SPECIFICALLY
DESIGNED FOR WASTEWATER
CROSS SECTION
OF FLORIDA
BIOLINE DRIPLINE
Dripper inlets are
positioned in the
center of flow where
water is the cleanest
APPLICATIONS
PRODUCT ADVANTAGES Typically installed following a treatment
Pressure compensation - all drippers deliver equal flow, even on process
sloped or rolling terrain. Can be used with domestic septic tank
Unique flow path - Turbonet technology provides more control of effluent with proper design, filtration and
water and a high resistance to clogging. operation
Continuous self-flushing dripper design - flushes debris, as it is Reuse applications including municipally
detected - throughout operation, not just at the beginning or end of a treated effluent designated for irrigation and
cycle. Ensures uninterrupted dripper operation. other disinfected and non-disinfected water
Single hole dripper outlet from tubing: sources.
- Better protection against root intrusion
SPECIFICATIONS
- Allows the dripline to be used in subsurface applications without
Dripper flow rates: 0.4, 0.6 or 0.9 GPH
need for chemical protection
Dripper spacings: 12, 18 or 24 dripper
Drippers capture water flow from the center of the tubing - ensures
spacings and blank tubing
that only the cleanest flow enters the dripper.
Pressure compensation range: 7 to 58 psi
Built-in physical root barrier - drippers are protected from root
intrusion without the need for chemical protection. Water exits dripper Maximum recommended system pressure:
in one location while exiting the tubing in another. 58 psi
Three dripper flow rates - provides the broadest range of flow rates Tubing diameter: 0.66 OD, 0.56 ID
available. Allows the designer to match the dripline to any soil or slope Tubing color: Purple color indicates non-
condition. potable
Florida Bioline tubing is completely wrapped in purple - easily Coil lengths: 500 or 1,000 (Blank tubing in
identifying it for non-potable use, regardless of how the tubing is 250)
installed. Recommended filtration: 120 mesh
Can be used subsurface - Florida Bioline can be installed on-surface, Bending radius: 7
under cover or subsurface. UV resistant
No special storage requirements - does not degrade if stored Tubing material: Linear low-density
outdoors. polyethylene
Techfilter compatible - an optional level of protection, provides a
limited lifetime warranty against root intrusion. Additional spacing and pipe sizes available
by special order. Please contact Netafim USA
Customer Service for details.
FLORIDA BIOLINE DRIPLINE
MAXIMUM LENGTH OF A SINGLE LATERAL WITH 3.0 fps FLUSH VELOCITY MAXIMUM LENGTH OF A SINGLE LATERAL WITH 1.5 fps FLUSH VELOCITY
ADDITIONAL FLOW OF 2.3 GPM REQUIRED PER LATERAL TO ACHIEVE 3 fps ADDITIONAL FLOW OF 1.2 GPM REQUIRED PER LATERAL TO ACHIEVE 1.5 fps
DRIPPER SPACING 12 18 24 DRIPPER SPACING 12 18 24
DRIPPER FLOW RATE (GPH) 0.4 GPH 0.6 GPH 0.9 GPH 0.4 GPH 0.6 GPH 0.9 GPH 0.4 GPH 0.6 GPH 0.9 GPH DRIPPER FLOW RATE (GPH) 0.4 GPH 0.6 GPH 0.9 GPH 0.4 GPH 0.6 GPH 0.9 GPH 0.4 GPH 0.6 GPH 0.9 GPH
15 102 94 84 136 127 113 161 151 137 15 201 171 140 275 235 194 337 289 241
INLET PRESSURE
INLET PRESSURE
25 151 136 118 203 184 161 245 223 197 25 266 222 179 366 308 251 453 383 313
35 193 171 146 260 232 200 315 283 245 35 316 262 210 437 365 295 543 455 369
40 211 186 158 286 254 218 347 311 267 40 337 280 223 469 391 313 583 487 393
45 228 200 169 310 274 233 377 335 287 45 358 296 235 497 413 331 619 517 415
Flow per 100 (GPM / GPH) 0.67/40 1.02/61 1.53/92 0.44/26.67 0.68/41 1.02/61 0.34/20 0.51/31 0.77/46 Flow per 100 (GPM / GPH) 0.67/40 1.02/61 1.53/92 0.44/26.67 0.68/41 1.02/61 0.34/20 0.51/31 0.77/46
Lateral lengths are based on flows allowing for a 3 fps flushing/scouring velocity Lateral lengths are based on flows allowing for a 1.5 fps flushing/scouring velocity
MAXIMUM LENGTH OF A SINGLE LATERAL WITH 2.5 fps FLUSH VELOCITY MAXIMUM LENGTH OF A SINGLE LATERAL WITH 1.0 fps FLUSH VELOCITY
ADDITIONAL FLOW OF 2.0 GPM REQUIRED PER LATERAL TO ACHIEVE 2.5 fps ADDITIONAL FLOW OF 0.8 GPM REQUIRED PER LATERAL TO ACHIEVE 1.0 fps
DRIPPER SPACING 12 18 24 DRIPPER SPACING 12 18 24
DRIPPER FLOW RATE (GPH) 0.4 GPH 0.6 GPH 0.9 GPH 0.4 GPH 0.6 GPH 0.9 GPH 0.4 GPH 0.6 GPH 0.9 GPH DRIPPER FLOW RATE (GPH) 0.4 GPH 0.6 GPH 0.9 GPH 0.4 GPH 0.6 GPH 0.9 GPH 0.4 GPH 0.6 GPH 0.9 GPH
15 128 115 100 172 155 136 205 187 165 15 248 205 163 344 285 228 427 355 285
INLET PRESSURE
INLET PRESSURE
25 183 161 137 248 220 188 301 268 231 25 315 258 203 440 361 286 549 453 359
35 228 198 166 310 272 229 379 333 283 35 367 299 234 513 419 331 643 527 417
40 248 214 178 338 295 247 413 362 305 40 389 316 248 545 445 350 683 559 441
45 266 229 190 364 316 263 447 389 327 45 409 332 260 574 468 367 721 589 463
Flow per 100 (GPM / GPH) 0.67/40 1.02/61 1.53/92 0.44/26.67 0.68/41 1.02/61 0.34/20 0.51/31 0.77/46 Flow per 100 (GPM / GPH) 0.67/40 1.02/61 1.53/92 0.44/26.67 0.68/41 1.02/61 0.34/20 0.51/31 0.77/46
Lateral lengths are based on flows allowing for a 2.5 fps flushing/scouring velocity Lateral lengths are based on flows allowing for a 1 fps flushing/scouring velocity
MAXIMUM LENGTH OF A SINGLE LATERAL WITH 2.0 fps FLUSH VELOCITY MAXIMUM LENGTH OF A SINGLE LATERAL WITH 0.5 fps FLUSH VELOCITY
ADDITIONAL FLOW OF 1.6 GPM REQUIRED PER LATERAL TO ACHIEVE 2.0 fps ADDITIONAL FLOW OF 0.4 GPM REQUIRED PER LATERAL TO ACHIEVE 0.5 fps
DRIPPER SPACING 12 18 24 DRIPPER SPACING 12 18 24
DRIPPER FLOW RATE (GPH) 0.4 GPH 0.6 GPH 0.9 GPH 0.4 GPH 0.6 GPH 0.9 GPH 0.4 GPH 0.6 GPH 0.9 GPH DRIPPER FLOW RATE (GPH) 0.4 GPH 0.6 GPH 0.9 GPH 0.4 GPH 0.6 GPH 0.9 GPH 0.4 GPH 0.6 GPH 0.9 GPH
15 161 141 119 217 191 164 263 233 201 15 301 242 188 422 341 265 531 429 335
INLET PRESSURE
INLET PRESSURE
25 221 190 157 302 261 218 369 321 270 25 369 296 228 520 418 323 655 527 409
35 269 229 187 370 316 260 455 391 324 35 421 337 260 595 476 368 749 603 467
40 290 246 200 399 340 278 493 421 347 40 443 354 273 626 501 387 790 635 491
45 310 261 212 427 362 296 527 449 369 45 464 371 285 656 524 404 829 665 513
Flow per 100 (GPM / GPH) 0.67/40 1.02/61 1.53/92 0.44/26.67 0.68/41 1.02/61 0.34/20 0.51/31 0.77/46 Flow per 100 (GPM / GPH) 0.67/40 1.02/61 1.53/92 0.44/26.67 0.68/41 1.02/61 0.34/20 0.51/31 0.77/46
Lateral lengths are based on flows allowing for a 2 fps flushing/scouring velocity Lateral lengths are based on flows allowing for a 0.5 fps flushing/scouring velocity
Netafim recommends flushing velocities capable of breaking free any accumulated bioslimes and debris in the piping network.
Notes: 1. Refer to local regulations for information on flushing velocities that may be written into codes.
2. Netafim does not endorse a specific flushing velocity.
3. Flushing velocities should be determined based on regulations, quality of effluent, and type of flushing control.
4. Using a flushing velocity less than 1 fps does not provide turbulent flow as defined by Reynolds Number.
5. Higher flushing velocities provide more aggressive flushing.
EXPLODED VIEW OF FLORIDA BIOLINE DRIPPER FLORIDA BIOLINE DRIPPER OPERATION
Bottom View Top View Florida Bioline drippers are pressure compensating
Large inlet filtration area
- delivering the water uniformly into the soil for further
(bottom of dripper) Dripper Outlet treatment or for reuse by the landscape. These unique
(top of dripper) drippers allow the tubing to be installed on flat topography
or steep slopes.
Netafim drippers are continuously self-cleaning during
Physical barrier separates where
water leaves the dripper from operation, not just at the beginning and end of a cycle. The
Chemical-resistant where it leaves the tubing. result is dependable, clog-free operation, year after year.
molded silicon
diaphragm
Drippers Top View
Top of dripper (turned over)
TurboNet wide
flow path
DRIPPER FLOW RATE VS. PRESSURE
1.0
0.9 0.9 GPH FLOW PER 100 FEET
0.8
DRIPPER 0.4 GPH DRIPPER 0.6 GPH DRIPPER 0.9 GPH DRIPPER
FLOW RATE (GPH)
0.7
0.6 0.6 GPH
SPACING GPH GPM GPH GPM GPH GPM
0.5 12" 40.0 0.67 61.0 1.02 92.0 1.53
0.4 0.4 GPH
18 26.7 0.44 41.0 0.68 61.0 1.02
0.3
0.2 24 20.0 0.34 31.0 0.51 46.0 0.77
0.1
0
10 20 30 40 50 58
PRESSURE (psi)
Between 0 and 7 psi, the dripper functions as a
turbulent flow emitter, ensuring that the nominal
design flow is not exceeded at system start-up. FLORIDA BIOLINE ORDERING INFORMATION
FLOW DRIPPER COIL MODEL
RATE SPACING LENGTH NUMBER
1,000' 08WRAM.4-12
0.4 GPH 12"
500' 08WRAM.4-12500
SPECIFYING INFORMATION
1,000' 08WRAM.4-18
0.4 GPH 18"
SAMPLE MODEL NUMBER 500' 08WRAM.4-18500
1 2 3
A 1,000' 08WRAM.4-24
0.4 GPH 24"
Florida
Bioline = 08WRAM 08WRAM.6-24 500' 08WRAM.4-24500
Dripline A 1,000' 08WRAM.6-12
0.6 GPH 12"
500' 08WRAM.6-12500
1 2 3
DRIPPER DRIPPER COIL 1,000' 08WRAM.6-18
FLOW RATE SPACING LENGTH
0.6 GPH 18"
500' 08WRAM.6-18500
0.4 GPH = .4 12 = 12 500 = 500 1,000' 08WRAM.6-24
0.6 GPH = .6 18 = 18 1,000 = LEAVE 0.6 GPH 24"
500' 08WRAM.6-24500
0.9 GPH = 1 24 = 24 BLANK
1,000' 08WRAM1-12
0.9 GPH 12"
500' 08WRAM1-12500
BLANK Tubing Model Number: 250 = 08WRAM-250
1,000' 08WRAM1-18
0.9 GPH 18"
500' 08WRAM1-18500
1,000' 08WRAM1-24
0.9 GPH 24"
500' 08WRAM1-24500
Blank Tubing 17mm 250' 08WRAM-250
FLORIDA BIOLINE FITTINGS
FITTING APPLICATIONS
Fits Florida Bioline Dripline
FITTING SPECIFICATIONS
Barbed fittings for a secure fit
Easy installation without glue or tools
Allows for easy on-site inspection of proper fitting installation
TLCOUP TLELL TLTEE TLCROS
Insert Coupling Insert Elbow Insert Tee Insert Cross
TL050MA TL075MA TL075FTEE TL2W075MA
Male Adapter Male Adapter Combination Tee 2-Way Insert
Ins x Ins x FPT MPT x Insert
TLIAPVC-B TDBIT16.5
TLIAPE-B Insert Adapter with Grommet Drill Bit for TLIAPVC
Insert Adapter for 1 or 1 or larger PVC Pipe Fitting (16.5mm or 21/32)
Larger PE (Requires 11mm
or 7/16 drill or punch)
FITTING DEFINITIONS
FPT = Female Pipe Thread
MPT = Male Pipe Thread
TLFIG8 TLS6 Ins x Ins = Insert by Insert
Figure 8 Line End 6 Soil Staple
TLSOV TLCV
Shut-Off Valve Inline Check Valve
Ins x Ins Flow Range: 0.9 to 4.4 GPM
NETAFIM USA
Opening Pressure: 10.2 psi 5470 E. Home Ave.
Closing Pressure: 5.8 psi Fresno, CA 93727
(13.4 Feet Column of Water) CS 888 638 2346
www.netafimusa.com
W064FL 10/16
