Technical Data Sheet
Approved 24620;24680 1 24620 epoxy ^(ValidationDate) 1
Penguard HSP MIO E
Product description
This is a two component amine cured epoxy coating. This product is LEED compliant and contains no solvents on
the Hazardous Air Pollutants (HAPs) list. It is a fast drying, micaceous iron oxide (MIO) pigmented, high solids,
high build product. Can be used as primer or mid coat in atmospheric environments. Specially designed for new
construction where fast dry to handle and over coating times are required. Suitable for properly prepared
aluminum, carbon steel, galvanized steel, shop primed steel and stainless steel substrate.
Typical use
Suitable for structural steel and piping to be exposed to corrosive environments. Recommended for power plants,
airports, buildings, refineries and mining equipment.
Other
Approvals and certificates
Contributes to satisfying the following credit(s)
- Indoor Environmental Quality (IEQ) under LEED 2009
Additional certificates and approvals may be available on request.
Other variants available
Penguard HSP E
Penguard HSP ZP E
Refer to separate TDS for each variant.
Colors
selected range of colors
Product data
Property Test/Standard Description
Solids by volume ISO 3233 75 2 %
Gloss level (GU 60 ) ISO 2813 matt (0-35)
Flash point ISO 3679 Method 1 81 F (27 C)
Density calculated 1,7 kg/l
VOC-US/Hong Kong US EPA method 24 (tested) 2,07 lbs/gal
The provided data is typical for factory produced products, subject to slight variation depending on color.
All data is valid for mixed paint.
Gloss description: According to Jotun Performance Coatings' definition.
Date of issue: 25 October 2016 Page: 1/5
This technical data sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Penguard HSP MIO E
Film thickness per coat
Typical recommended specification range
Dry film thickness 2,4 mils (60 m) - 10 mils (250 m)
Wet film thickness 3 mils (80 m) - 13 mils (335 m)
Theoretical spreading rate 510 ft/gal (12,5 - 120 ft/gal (3 m/l)
m/l)
103,8 - 120 ft/gal (3 m/l)
Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.
Surface preparation summary table
Surface preparation
Substrate Minimum Recommended
Carbon steel St 2 (ISO 8501-1) Sa 2 (ISO 8501-1)
Stainless steel The surface shall be hand or machine Abrasive blast cleaning to achieve a
abraded with non-metallic abrasives surface profile using approved non-
or bonded fibre machine or hand metallic abrasive media which is
abrasive pads to impart a scratch suitable to achieve a sharp and
pattern to the surface and to remove angular surface profile.
all polish from the surface.
Aluminum The surface shall be hand or machine Abrasive blast cleaning to achieve a
abraded with non-metallic abrasives surface profile using approved non-
or bonded fibre machine or hand metallic abrasive media which is
abrasive pads to impart a scratch suitable to achieve a sharp and
pattern to the surface and to remove angular surface profile.
all polish from the surface.
Shop primed steel Dry, clean and intact shop primer. Abrasive swept or alternatively
blasted to Sa 2 (ISO 8501-1) of at
least 70 % of the surface.
Galvanized steel The surface shall be clean, dry and Light brush blasting using non-
appear with a rough and dull profile. metallic abrasive leaving a clean,
rough and even pattern.
Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating (ISO 12944-4 6.1) coating (ISO 12944-4 6.1)
Application
Application methods
The product can be applied by
Spray: Use airless spray.
Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.
Date of issue: 25 October 2016 Page: 2/5
This technical data sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Penguard HSP MIO E
Product mixing ratio (by volume)
Penguard HSP MIO E Comp A 4 part(s)
Penguard HSP E Comp B 1 part(s)
Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 26
Guiding data for airless spray
Nozzle tip (inch/1000): 17-23
Pressure at nozzle (minimum): 150 bar/2100 psi
Drying and Curing time
Temperatures:
-10C = 14F / -5C = 23F / 0C = 32F / 5C = 41F / 10C = 50F / 15C = 59F / 23C = 73F / 35C = 95F / 40C = 104F / 100C = 212F
Substrate temperature 0 C 5 C 10 C 23 C 40 C
Surface (touch) dry 11h 5h 2h 1h 30min
Walk-on-dry 18h 12h 6h 3h 2h
Dried to over coat, minimum 18h 12h 4h 2h 1h
Dried/cured for service 21d 13d 8d 4d 3d
Drying and curing times are determined under controlled temperatures and relative humidity below 85%, and at
the typical DFT for the product.
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.
Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.
Dry to over coat, minimum: The shortest time allowed before the next coat can be applied.
Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.
Induction time and Pot life
Temperatures: 15C = 59F / 23C = 73F
Paint temperature 23 C
Pot life 2h
Date of issue: 25 October 2016 Page: 3/5
This technical data sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Penguard HSP MIO E
Heat resistance
Temperature
Continuous Peak
Dry, atmospheric 120 C 140 C
Peak temperature duration max. 1 hour.
The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.
Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Previous coat: epoxy, epoxy mastic, inorganic zinc shop primer
Subsequent coat: acrylic, epoxy, polyurethane, polysiloxane
Packaging (typical)
Volume Size of containers
(liters) (liters)
Penguard HSP MIO E Comp A 16 20
Penguard HSP E Comp B 4 5
4 l = 1.06 gal
16 l = 4.23 gal
The volume stated is for factory made colors. Note that local variants in pack size and filled volumes can vary
due to local regulations.
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.
Shelf life at 73F (23 C)
Penguard HSP MIO E Comp A 12 month(s)
Penguard HSP E Comp B 24 month(s)
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.
Date of issue: 25 October 2016 Page: 4/5
This technical data sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Penguard HSP MIO E
Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.
Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
Color variation
When applicable, products primarily meant for use as primers or antifoulings may have slight color variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.
Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.
Date of issue: 25 October 2016 Page: 5/5
This technical data sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
