Machines
General Requirements
Self-Inspection Checklist
Guidelines: This checklist covers machines which require guards to protect the operators and others near the machines from
hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks. Examples of guarding
methods are barrier guards, two-hand tripping devices, and electronic safety devices.
Please Circle
1. Are all machines guarded to protect the operator and other people in Y N N/A
the machine area from hazards such as those created by point of
operation, ingoing nip points, rotating parts, flying chips, and sparks?
[29 CFR 1910.212(a)(1)]
2. Is the point of operation guarded, in conformity with appropriate Y N N/A
standards, if operation of machinery exposes individuals to injury?
[29 CFR 1910.212(a)(3)(ii)]
Note: In the absence of applicable specific standards, guarding shall be
so designed and constructed as to prevent the operator from having
any part of his/her body in the danger zone during the operating cycle.
Examples of cited violations include: paper cutters had no finger
guards, a radial arm saw's blade protruded beyond the edge of the
cutting table during its operating cycle, bench and pedestal drills had no
bit guards, and lathes had no shields.
3. Are guards attached to the machine when possible, and if that is not Y N N/A
possible, attached elsewhere? [29 CFR 1910.212(a)(2)]
4. If hand tools are used for placing or removing material, are they Y N N/A
designed to be easily handled without a need to place hands in a
danger zone? [29 CFR 1910.212(a)(3)(iii)]
Note: Such tools are not a substitute for guarding.
They can only be used as supplemental protection.
5. Are revolving drums, barrels and containers guarded by an enclosure Y N N/A
that is interlocked so that containers cannot revolve unless the
enclosure is in place? [29 CFR 1910.212(a)(4)]
6. Are all fans less than 7 feet from the floor equipped with guards that Y N N/A
have openings no larger than one-half (1/2) inch?
[29 CFR 1910.212(a)(5)]
Note: Examples of cited violations include: exhaust fan blades and floor
fans were not provided with protective guards, a portable table fan had
a blade guard whose openings were approximately one inch
in width, and a guard was broken creating a hole approximately 4" x 2."
7. Is all machinery designed for a fixed location securely anchored to Y N N/A
prevent "walking" or "moving?" [29 CFR 1910.212(b)]
8. Are all machines constructed, installed and maintained as to be free Y N N/A
from excessive vibration or play? [Recommended]
9. Are all machines and equipment requiring the presence of an operator Y N N/A
not left unattended while in operation or still in motion?
[Recommended]
10. Are all machines provided with a power cut off switch that can be Y N N/A
reached from the operating position? [Recommended]
11. Is all fixed motorized machinery equipped with a magnetic-type switch Y N N/A
designed to prevent automatic restarting of machinery when power is
restored after a power failure or electrical cutoff?
[29 CFR 1910.213(b)(3)]
12. Are all machine operating controls easily reachable from the standard Y N N/A
operating position and away from any hazardous point of operation?
[29 CFR 1910.213(b)(4)]
13. Are all electrically powered machines provided with a positive means for Y N N/A
rendering the motor starting controls inoperative while repairs or tool
changes are being made? [29 CFR 1910.213(b)(5)]
14. Is your shop or lab equipped with two or more push-type emergency Y N N/A
cut-out switches, provided at appropriate locations for each (maximum)
1000 square feet of shop floor area, for de-energizing the electrical
supply to nonportable machinery. [Recommended]
Note: The switch must have a clear unobstructed access of at least 36
inches. In addition, the reset of the switch must be key operated.
15. Are all power tools and machines which generate dust connected to a Y N N/A
dust collection system? [Recommended]
16. If required in your state, are dust collections systems permitted by the Y N N/A
* appropriate state agency? [see the Air Pollution Control checklist]
