Cooling/Defrost Temperature Controller DIN W72 x H36mm Cooling/Defrost Temperature controller =|Features ON/OFF Control @lnput specification ® Basie specification:NT Option:RTD(DIN Pt10 @lncludes delay function Auto/Manual Thermistor) frost selection function, Start-up delay of compressor, Re-operation delay, Minimum ON time Delay of defrost~end, Operation input correction function It is available to set operation period for protecting compressor in error Vee ee Ais \Ordering information Te}|3\\Y\|{F| — | 1), 4][R lay of evaporation~fan poi 3 Power supply |= 240VAC S0/60Hz Sonvel outos 2_| Compressor+Defrost output ae y_[DIN w72x Hae Pot 3Diait Specifications oder Ta) Tea TOSYF=24R I TOaVF=34R (250VAC 5A 1 - ee beer Tfecharca Wi 70,000,000 tines, eeical "Win 00,000 umes @SOVAC TOR resiatve ad Vigration ‘0.5mm amplitude at frequency of 10 to 55Hz in each of X, ¥, Z directions for 10 minutes cs c=-46TC3YF =\Connections =\Dimensions ‘Panel cut-out Min. 91 t 4 Min of (Uniti) (© DEF (Detrast output lamp) : Light is ON when defrost outout is ON [2 FAN(Evaporationfan output lamp) : Light is ON when evaporation output is ON. [F COMP(Compressor output lamp) : Light is ON when compressor output Is ON & MD(Mode key) : For entering, changing shiting parameters IB ¥ A(Sotting key:Up/Down) : For changing parame [6 ~ : Displaying minus symbol [7 Display process value) : Display a current value (SV) on RUN 1 Display a parameter ang a setting value when setting parameter. [8 @ (Display a decimal point) : Display a decimal point when the time unit is "Min* [8 @(Display a decimal point) : Display a cecimal point when the temperature unit is "c" A, m, ¥ (Display a deviation) : “4 indication turns on when PV is higher than SV, ¥" ingication turns on when PV is lower than SV ©, “F(Temperature unit) ! Selectable T or F When delay time Is applied, the output lamp of defrost output, evaporation—fan and compressor 's ON simultaneously a‘ter the lamp flashes every one second. ‘miHow to set and change setting value(s.) Olnput specification and range Display a current temperature. — Display ‘Su" when pressing PO] key. zs ‘The serting range of temperature is xed ast ng range ‘A setting value flashes every 0.5 sec. and itis available to = TOD] | chanve the value with[ax}or [v]key #Wnen pressing is saved and t the sett & ‘If any Key is untouched for 60seo, it returns to operation mode When pressing [HD] key for displaying setting value, it returns to operation mode When [¥] key at "ON", minus values are available to se Pressing [a}key ([¥] key) continuously, a number is increases/decrea c-47 AutonicsCooling/Defrost Temperature Controller ‘Flow chart for setting group 1 RUN mode [Pes ays |—==—+_ i Sot a detrosting period with '1f defrosting interval is se Seta del I dott 19 poriog with interval is Set monitoring time for SIF monitoring time enters into setting group 1 Tho setting range is ~10.0~ Set a hysteresis of compressor output within ak ala BA dos 10.0% minutes. does not operates S0F, operated as a manual m within 099986 or generated in input sensor Factory defaults Win KUW mode, Ei]eey is pewsed lor Osc ods [Sorin vate] Hots [Sting ae ting group 1 HS) 10 iba 2 eve te changed sting veh Pep ee EEL aches may for 3 min during sting operation i returns to RUN mode =IFlow chart for setting group 2 Factory defaults Wade [Satna wae] Woot [Sina Sat 20 TLE o and re-operation Seif fe ui : . deP[ 100 [Une Te etng age Orn 8-99, geet im Lune f Set operation interval o he setting range is O~ fa a a ON operation rat ting range is O~ c] set mova un of ate op c a oFF sar LC aril? ar tld o @ o end and evaporation=tan, 8 fe] a aw 7] Set me evaporaton-tan operation mode Fie EF tl cs Bere steer st crusts ers (2%) of compressor within eperation interval in exer oF Flinn Leg [emer ea wR LE. 1 [Senina ove P Leak LE 3 [Semen re Satna oou8 Set value SV) Lock lays atTC3YF ™Function and operation OHysteresis [HY5] @TC3YF operates as ON/OFF control and controls compressor output The compressor can be damaged by frequent ON/OFF cycle at setting value. Therefore it can establish Hysteresis between activation temperature and deactivation temperature to prevent the compressor. EX)If TC3YF is established as setting temperature (GU) as ~20, hysteresis (YS) as 1.0, the compressor output is ON when it is reached ~19T and it is OFF when it is reached ~21U ¥In ON/OFF control, the temperature is lower than SV, the output is OF and it is also designated as dual position contro! The setting range of hysteresis is 0.5~10.0°C (2~50°F) Olnput correction [nb ] It corrects an error generated by temperature sensor inputt and it is ON when it is higher 5x) When room temperature is -18, the display temperature of temperature controlle input correction (mb) value as 2.0, itis corrected as ~ 18 The setting range of input correction is ~10,0T~10,0%, (~18~18°F) ODefrost When compressor is operated for a long time, the efficiency is lowered by the frosts evaporator and freezer built in. A defrost designates to remove frost and ice around the evaporator. Heating defrost(Auto defrost) 20°, set the Mount 2 heater next to an evaporator and operate it with defrost intervalld fal and time [dE E] of temperature controller, removing frost and ice Manual defrost When pressing & key is pressed for 3 sec, compressor operation, ‘The prior defrost interval value is not deleted When pressing key for 3 see, it returns to auto defrost. (The defrost internal starts again from defrost output is OFF.) When defrost interval is set to °0.0" , itis only operated as manual defrost. 1e defrosting is activated for defrost time (dE t] during the we When it used as manual defrost, compressor output and evaporationfan output are OFF when the defrost output is ON ¥ The selling range of defrost intervalld tal is 0~24 hours and defrost lime [dE] is 0~59 min, ©Freezing(Compressor) operation Temperature control : Keep the setting temperature by repeating ON/OFF operation in the range of hysteresis. Tha datay The dotey ime Minimum Above 28%] ime of eat, ol ro=aperato ON time sue 8 MEL: The output is not operated, only the front COMP lamp is Slashing. The delay time of start-up and re-operation [Sdt ] L)Delay of start-up : When applying the power again on 2 compressor after power is failed, the ompressor will be overloaded. In this case, delay of start-up prevents curtailing of the life cycle of a compressor. The setting range is Oml0s~9m59s, The output lamp is ON simultaneously after the lamp flashes every one second during delay time. 2)Delay of re—operation : It does not operate within delay time of re—operation after compressor turned OFF to prevent frequent ON/OFF. The setting range is Om10s~9m59s, (41)For delay time of start-up, compressor output is OFF even when PV is lower than SV. Iis turned ON after delay time of re-operation is over. ‘eMinimum ON time [ont] Set a minimum ON time to prevent frequent ON/OFF. The setting range is OmL0s~m00s, % (*2)Compressor output is ON even when PV is lower than hysteresis. It is turned to OFF after the minimum ON time is over. c-49 AutonicsCooling/Defrost Temperature Controller ODefrost operation(Heating defrost) Operation erm Cooling Oration tom Detros Dotrost caro oy ete sth Datta interval ime ced | naval time =e interval Detrost time EF 1 Evaporation—fan [ [ evaperation=tan lvaparation~fan evaporation fan EF2 Evaporation—tan | Zo a Citaoaerta LO eFtevarontion-in| EFS Evaporation—fan Power ON MMII The display lamp is only ashing, (The output is not operated) Defrost interval [d In] Ir starts to defrost for relevant interval. The setting range is 0~24 ho! When the defrost interval is set to "0.0", itis only operated as manual Defrost time [ JE] The defroster (heater) '5 ON during defrost time, The setting range is Om~59m, ‘©The delay time of defrost-end / evaporation-fan operation [Dripping Time : dP ] D)The delay time of defrost—end : It is the time for draining remained drops, After the delay time is over, compressor sta operating. (The setting range ! Om00s~5m59s) 2)'The delay time of evaporation~fan operation : ‘To improve the efficiency of cooling, evaporation fan is delayed until evaporation plate gets frozen operation of alter compressor operating. (The setting range ! OmO0s~Sm59s) The delay time of defrost—end and evaporationfan operation are a fied with one setting time, le P) When the delay time of defrost—end is finished, defrost is discontinued and defrost interv The output lamp is ON simul Lis repeated ay time neously after the lamp flashing every one second during the Evaporation operation mode [An] ‘Operation mode 1[ EF 1] : It operates same as freezer Operation mode 2( EF2 } : It operates after the delay time of evaporation~f defros operation. operation. OFF during Operation mode 3 EF] : It is started when the power is applied and only operated during the defrost interval. (It does not any influence upon the freezer.) Operation mode 4[ EF4 ] : The evaporation—fan operates only in the operation term of freezer or defrost, it is OFF when compressor and defroster are stopped (it is used to control the above zero temperature.) Operation mode 5[ EFS ] : It is started when the power is applied and it w. ODisplay an error Err mark and content are flashing every 0.5 sec when error ks until the power is failed Err aPa_| Input sonsoris disconnected Tnpul sensor ls normal or freezer lemperalure is nol changed over 1.00( observation time(LbA) of loop 6 Eres tba Ere / LLL | Process temperature (PV) is lower than the display range Ere) HHH | Pro ‘The error display of oPA/LLUMHH disappears after the abnormal factors are cleared. (Sensor connection/returning to the display range) ess temperature (PV) is higher than the play ange AutonicsTC3YF Operation cycle [CLE] / ON duty ratio of compressor in error [ dUE ] When an error occurs, repeats ON/OFF operation based on setting values of Operation eyelo operation cyele(€LE) and ON duty ratio(UE) of second setting group to protec of compressor The setting range of operation cycle ! 0~20 min, ‘The setting range of ON éuty ratio : 0~ 100% on When operation cycle of compressor is "0", it keeps OFF status in Compressor OF error. The ON duty ratio (@UB) is not displayed in error. The duty ratio of compressor ON is "100", it keeps ON status in error. Alarming of loop disconnection(LBA : Loop Break Alarm) When the cooling temperature is not changed over 1.0°C(2°F) during monitoring time set at loop break alarm(LbA) parameter, it is regarded as abnormal aperation. It displays Ere and LBA every 0.5sec and the compressor output repeats ON/OBF by the operation eycle(£LE) and ON duty ratio (@UE) seiting in error When pressing [H5] key simultaneously for see, after checking the compressor, it operates normally with cancelling the error. LBA function does not operated when LBA value is at "0 (LBA setting range : 0-9998e0) OSet the Lock [L00] Limit the change of OFF Lock off LO. 1: Lock the second setting group C.2 Lock the fi £.3 : Lock the first and second setting groups and SV SV and parameter. st and second setting groups Proper usage 1. Please beware not to exceed the rated specification of relay when using relay contact or it may cause a fire with breakdown 2, Please mount a surge absorption device at coil when controlling high-capacity power relay or a magnet, the counter electromotive force can be flowed into the inside of the device for relay contact operation Please install a power switch or circuit breaker in order to cut power supply off, ‘The switch or a circuit breaker should be installed near by user for easy operation. Do not use this temperature controller as a Voltmeter or Ampere~meter. In case of using RTD sensor, please connect as 3 wire type and use 3 same thickness of lines when you need to extend. It might cause the deviation of temperature if the resistance of line is different 7. Please check the polarity and connect correctly when connecting RTD sensor to temperature controller, NTC sensor is a non—polarity. 8. In case of making power line and input signal line close, line filter for noise protection should be installed al power line and inpul signal line should be shielded (Note) Please make sensor line shortly and use it because the narrow range of inpu 8. Keep away from the high frequency instruments. (High frequency welding machine & sewing machine, high~capacity SCR controller ete.) 10, Please use AWG No. 12~28 for power input and relay output connection, fasten the terminal block as a orque 0.3Nm. 11. Installation environment Dit shall be used indoor @Pollution Degree 2 @Altitude Max. 2000m installation Category IL correction range. c-51 Autonics