KGC RESOURCES SDN BHD MALAYSIA

ACKNOWLEDGMENT
MESSAGE FROM OUR MANAGEMENT

Dear Our Valued Customer and Business Partners,

T hank you for being our valued customers. We are grateful for the pleasure of serving you and meeting
your laboratory and research equipment needs. In this time of gratitude, we also thank you for your
continued support for trusting us and our products. Henceforth, we value your patronage and appreciate
your confidence in us. Counting you among our customers is something which we are grateful for.
This year, it has been challenging year, but we have overcome these challenges in triumph- with
help of you and your fellow researcher, engineers and scientist. All of you have worked hard allowing our
business to thrive.
On behalf of the management and staff of KGC Resources Sdn Bhd, we are once again grateful
and thank you for your support and continuous loyalty to us. We try to keep our price low and In fact we
are maintaining the price for most of the products. In addition, we provides some information on battery
research flow chart which may become handy to whoever is doing the battery research.
We hope that you will enjoy our promotion catalog and we promise to offer you with our best and
lower and attractive price. Please feel free to browse our e-product catalog and e-promotion catalog on
www.kgcscientific.com and/or www.kgcresources.com.
Thank you!

MAP TO OUR COMPANY

INTRODUCTION

KGC RESOURCES SDN BHD

No. 2-2-3, Jalan Setia Prima E
U13/E, Setia Alam, Seksyen U13
40170 Shah Alam
Selangor Darul Ehsan, Malaysia

2 KGC RESOURCES designed by kafka

KGC RESOURCES SDN BHD MALAYSIA

TABLE OF CONTENTS
ADVANCED MATERIAL SCIENCE 4
MTI USA 4
TORREY HILLS USA 13
HANTECH KOREA 13
BERKELEY SCIENTIFIC USA 14
OIL & GAS INSTRUMENTATION 17
GASTECH AUSTRALIA 17

TABLE OF CONTENTS
IMR USA 18
HTA ITALY 19
BIOTECHNOLOGY & LIFE SCIENCE 20
BE MARUBISHI JAPAN 20
QUANTEK INSTRUMENTS USA 22
HEB CHINA 23
HYSC KOREA 23
LABORATORY EQUIPMENT 24
NEW ERA USA 24
HYSC KOREA 26
SAMHEUNG ENERGY KOREA 27
MTI USA 28
SLI INSTRUMENTS CHINA 30
NANOMATERIAL & SEMICONDUCTOR 31
LJUHV TAIWAN
LI-ION BATTERY FABRICATION 35
MTI USA

CUSTOMIZED DESIGN
Plug Flow Reaction Tube Walk-In Laboratory Room

Membrane Filtration System KGC RESOURCES SDN BHD was formed to deliver innovative laboratory
equipment designs to science and research industry. We have combined
experienced and talented engineers to understanding end users’ needs
from developing the designs, fine tuning the mechanical works until the
fabrication parts. Our engineers are young but talented and we pride
ourselves in our tag line: STRENGTH THROUGH INNOVATION.

We have been involved in constructing Walk-In Laboratory Room, Plug Flow

Reaction Tube, Membrane Filtration System, Corrosion Control Test, Heat
Transfer System and many others in various fields that are related with
research purpose. Any inquiry please feels free to contact us.

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 3

 MTI USA

TUBE FURNACE
GSL-1100X-50-LVT OTF-1200X-S-VT

OTF-1200X-4-RTP

GSL-1100X OTF-1200X-S50-2F

OTF-1200X-S

Quartz Tube Heating Working

Model Features Advantages Price
Option Rate Temperature
GSL-1100X 1” O.D. Max: 20°C /min Max: 1100°C  Dial Vacuum Gauge The chamber can be set
or (< 1 hour) up in vertical, horizontal, RM 12,350
2” O.D. Cont: 1000°C or at an angle
ADVANCED MATERIAL SCIENCE

GSL-1100X- 1” O.D. Max: 20°C /min Max: 1100°C  Digital Vacuum Stainless steel shell with
50-LVT (< 1 hour) Gauge, Temperature adjustable height
RM 29,980
Cont: 1000°C Calibrator, Vacuum
Pump and Filter
OTF-1200X- 1” O.D. Max: 10°C /min Max: 1200°C  Digital Vacuum Can heat sample in
S50-LVT or (< 1 hour) Gauge, Temperature vacuum up to 1E-2 Torr
RM 29,680
2” O.D. Cont: 1100°C Calibrator, and or flowing gas.
Vacuum System
OTF-1200X- 2” O.D. Max: 10°C /min Max: 1200°C  Digital Vacuum Anti corrosive gauge to
S50-2F (< 1 hour) Gauge, Two Channel be used with aggressive
RM 31,380
Cont: 1100°C Gas Mixing Station, gases
and Vacuum System
OTF- 1” O.D. Max: 20°C /min Max: 1200°C  Dial Vacuum Gauge Split-able horizontal tube
1200X-S or (< 1 hour) furnace RM 14,380
2” O.D. Cont: 1100°C
OTF-1200X- 4” O.D. Max: 50°C /sec Max: 1100°C  Digital Vacuum Rapid thermal processing
4-RTP (< 10 min) Gauge system for fast heating
RM 57,250
Cont: 600°C and double layer steel
case
0TF-1200X- 1” O.D. Max: 20°C /min Max: 1200°C  Dial Vacuum Gauge Split-able vertical tube
S-VT or (< 1 hour) furnace RM 20,500
2” O.D. Cont: 1100°C

VACUUM CHAMBER FURNACE

Model VBF-1200X-H8-UL
Quartz Tube Size 8” O.D x 7.5” I.D.x 13.4“ L
Volume 7.6 L
Working Temperature Maximum 1100°C for 30 minutes and 1000°C continuously
Features • PID automatic control and auto-tune function
• Stainless steel vacuum flange with one needle valve as gas inlet
• One port for vacuum pump connection
• Digital vacuum gauge provided
UL Recognition All electric components are UL recognized

Price RM 52,098

4 KGC RESOURCES
MTI USA

MUFFLE FURNACE
Muffle furnace (400°C-1800°C) steps in as the necessary part of laboratory
that requires extreme heat environment. MTI is providing the muffle furnace
at an affordable cost. The sizes of the muffle furnace are various from the
smaller furnaces which are conveniently placed on a workbench, to the larger

ADVANCED MATERIAL SCIENCE

units that has a coveted capacity and competent for all duty.
General Features:
• PID automatic control and auto tune function temperature controller
• High purity alumina fiber insulation
• Double shell steel case

KSL-1200X-M
KSL-1500X-S
KSL-1100X-S
Chamber Dimension Heating Working Heating
Model Volume Power Price
LxWxH Rate Temperature Element
Max: 1200°C  (< 1 hour) Resistance
KSL-1100X-S 4” x 4” x 4“ 1L Max: 30°C /min 700 W RM 6,800
Cont: 1100°C Wire
Max: 1100°C  (< 1 hour) Resistance
KSL-1200X-L 16” x 16” x 16” 64 L Max: 20°C /min 5000 W RM 28,750
Cont: 1000 °C Wire
Max: 1200°C  (< 4 hour) Resistance
KSL-1200X-J 6” x 6” x 7” 4.2 L Max: 30°C /min 3000 W RM 10,850
Cont: 1100 °C Wire
Max: 1200°C  (< 1 hour) Resistance
KSL-1200X 12” x 8” x 5” 7.2 L Max: 50°C /min 3500 W RM 14,230
Cont: 1100°C Wire
KSL-1200- Max: 1200°C  (< 1 hour) Resistance
12” x 12” x 12” 27 L Max: 10°C /min 7000 W RM 20,286
X-M Cont: 1100 °C Wire
Max: 20°C / min Max: 1500°C (< 1 hour) Silicon
KSL-1500X-S 4.7” x 4.7” x 4.7” 1.7 L 2000 W RM 23,280
Cont: 10°C/min Cont: 1400°C Carbide
Max: 20°C / min Max: 1700°C  (< 3 hour) Molybdenum
KSL-1700X-S 4.7” x4.7” x 4.7” 1.7 L 3000 W RM 24,750
Cont: 10°C/min Cont: 1600°C Disilicide

SPIN COATER
VTC-50 VTC-100A VTC-200

Desktop Spin Coater with Complete Programmable Spin Coater with Vacuum Programmable Vacuum Chuck Spin Coater
Accessories Chucks, Oilless Vacuum Pump & Accessories with Complete Accessories
• 4” stainless steel spin plates are • Liquid disk made of polypropelene to resist • One 6” vacuum chuck is included for
included, which can hold one or multiple most of corrosive solutions (1”, 2”, & 4”) holding 6” and 8” wafers
samples by wax or double-sided tape • The spinning speed is variable from • 500 - 5000 rpm adjustable spinning speed
• The spinning speed is variable from 500-8000 rpm with two programmable • Digital control panel with two
0-5100 rpm segments programmable segments of different spin
• 20 ml syringe is included for liquid • One oilless vacuum pump and one filter times and speeds
injection with adjustable syringe holder are included • 20ml syringe is used to contain the
that can rotate freely along the support • 20ml syringe is used to contain the coating material
rod coating material
RM 10,980 RM 19,980 RM 21,225

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 5

 MTI USA

DIP COATER
PTL-MM01 PTL-MM02 PTL-200

Desktop Dip Coater with Variable Speed Programmable Dip Coater with Digital Controller PLC Controlled Dip Coater for Large Substrate
• Dipping speed is within 1-200 mm/mm • Dipping speed is within 1-200 mm/min • Coating samples with size up to 10” x 12”
adjustable adjustable • Pulling rate, immersion rate, dwell time
• Dipping traveling within 0-200 mm • Dipping traveling within 0-75 mm and cycling time are fully programmable
adjustable adjustable • 4 liter polypropylene tank is provided
• 150 ml solution container is included • 150 ml solution container is included • Max stroke length is up to 300 mm
• Sample weight less than 250g • Sample weight less than 250g • Max sample load is 7 kg
RM 15,750 RM 24,085 RM 30,530

HOT ROLLING PRESS

ADVANCED MATERIAL SCIENCE

MSK-HRP-MR100A MSK-HRP-01
4” Rolling Press with Dual 4” Hot Rolling Press
Micrometer • Max heating temperature:
• 100 mm Dia. x 100mm width 125°C
Rollers made from hardened • 100 mm Dia. x 100mm width
tool steel HRC60-62 Rollers made from hardened
• Dual micrometer for accurate tool steel HRC60-62
thickness adjustment in the • Calendering thickness in the
range 0 - 1.8 mm range 0 - 1.2 mm adjustable
• Constant Rolling Speed: 65 • Rolling speed 0 - 40mm /sec
mm / second adjustable
RM 23,380 RM 52,870

CUTTING AND DICING SAWS

SYJ-30 SYJ-40 SYJ-150

Digital Micrometer

Heavy Duty High Speed Abrasive Cut-off High Speed Diamond Cut-off Saw with Vise Digital Low Speed Diamond Saw with 4”
Saw with 10” SiC Cutting Blades and 4” Diamond Blades Precision Blades & Complete Accessories
• 10” SiC cutting blades are included • 4” impregnated diamond blades are • Variable 0 - 600 rpm with LED digital
• Max cutting section is up to 30 mm x included display
30 mm • Speed varies from 400 to 3250 rpm • Cutting width range is from 1mm - 24mm
• Manually push up with T clamp vise is • Flat saw table for easy trimming oversized by adjusting the LCD digital micrometer
included for quick tightening or release slabs • Max cutting depth is 55 mm when using
• Motor speed is 2800 rpm • Max cutting depth is 25.4 mm 25 mm O.D blade flange
• A cooling system is built in with inlet • Vise provided to handle the sample • Two angle adjustable sample holder is
and outlet provided smoothly included
RM 7,290 RM 3,800 RM 22,350

6 KGC RESOURCES
MTI USA

DC LOAD TESTER
EQ-M9711
DC Programmable Electronic Load for Battery and Capacitor Discharging Test
EQ-M9711 DC electronic load provides you with the flexibility to test a wide range of applications, such as testing power supply and
battery charger, testing battery or super-capacitor discharging performance etc.

ADVANCED MATERIAL SCIENCE

• Six high speed operation modes: CC,CR,CV,CW,CC+CV,CR+CW
• Over current, over voltage, over power, over heat, polarity reversed protection
• High-luminance VFD screen with two lines& four channels display
• Intelligent fan system will be automatically initiated according to the temperature
• Soft start time setting, carrying the power supplier according to the voltage value set
• Battery testing and short-circuit function
• Available of dynamic testing and rising edge and falling edge setting
• Supporting external trigger input and output
• External current waveform monitor terminal
• Supporting remote voltage compensation and multi-data storage
• Power-on-self-test, software calibration and standard rack mount
• Communication mode: USB port with software interface to PC
RM 5,850

LABORATORY MIXER
 MSK-USP-3N MSK-VUSP-12
Ultrasonic Processor for Ultrasonic Processor with
Dispersing, Homogenizing and Vacuum Chamber and Pump
Mixing Liquid Chemicals • Ultrasonic power up to 1200 W
• Ultrasonic power up to 300 W and 20 kHz frequency
and 20 kHz frequency • Liquid handling from 100 ml
• Liquid handling from 100 ml - 2000 ml
- 2000 ml • Digital timer range from 1 sec
• Digital timer range from 1 sec - 99 hours
- 99 hours • Temperature control built in
• Temperature sensor is installed • Vacuum level less than 1 Torr
RM 19,980 RM 54,960

VACUUM PEN
Model EQ-SMT-72-ESD
Features • A compact and portable pick-up tool, which can move chip, crystal wafer and
components safely and easily
• Vacuum suction is generated by pressing and releasing the trigger
• Four suction cups in different sizes are included, which can meet various specific
requirements
• The pen body is made of ESD silicon Rubber to ensure operation safely and cleanly
Suction Cups Four different sizes which are 6.4 mm, 9.5 mm, 12.5 mm and 19 mm made from
Diameter conductive silicone material
Price RM 150

ULTRASONIC CLEANER
Model EQ-VGT-1613QTD EQ-VGT-1620QTD
Inside Dimension 150 mm L x 140 mm W x 65 mm H 150 mm L x 140 mm W x 100 mm H
Volume 1300 ml 2000 ml
Ultrasonic Frequency 40 KHz
Ultrasonic Power 60 W
Features • 1-99 minutes adjustable, to accurately calculate second.
• Temperature setting: 20°C~80°C adjustable.
Price RM 1,248 RM 1,768

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 7

 MTI USA

BATTERY FABRICATION EQUIPMENT

MSK-115A MSK-170 MSK-112A

Compact Vacuum Sealer for Preparing Electrolyte Diffusion Chamber for Semi-Automatic Winding Machine for
Pouch Cell Professional Li-ion Battery Research Electrodes
• Sealing pressure up to 7 kg/cm2 adjustable • 0 - 1 MPa adjustable air pressure • Winding speed up to 250 rpm adjustable
• 200 mm L x 150 mm W max sealing • 326 mm L x 206 mm W x 148 mm H inner • Winding blade available for pouch cell and
dimensions chamber size cylindrical cell
• 5 mm edge sealing width • 0 - 99.99 sec air inflation time • Switchable between clockwise and
• 50 - 250°C adjustable sealing temperature • 0 - 99.99 sec vacuum condition hold time counterclockwise
• 50 - 250°C adjustable sealing temperature • -20 to 40°C operation temperature
• 0 - 99 Seconds adjustable heating timer • Easy program setting for specific vacuum
• Hard sealing blade (no tab in between) condition
RM 39,185 RM 37,580 RM 16,780
ADVANCED MATERIAL SCIENCE

MSK-330A MSK-500-18650 MSK-510-18650

Precise Pneumatic Point Welding Machine Desktop Semi-Auto Grooving Machine for Desktop Hydraulic Sealing Machine for
Various Cylinder Cell 26650, 18650, 32650, CR123, AA, AAA
• 10 kW max power • 400 grooving per hour productivity • Driving force using manual hydraulic
• 0.1 - 0.8 MPa air pressure range • > 0.5 MPa air pressure is required pressing up to 5T
• 0 - 99 A welding current • CR123 / 18650 / 26650 / 32650 / AA • Six standard die selectable
• 0.03 - 0.25 mm welding thickness selectable • It is necessary to groove the opening end of
• Controlled by microcontroller to achieve • 1.2 - 2.0 mm depth grooving dimensions the cylindrical case by using the MSK-500
monopulse, dipulse, & multiple-pulse • 1.1 - 1.5 mm width grooving dimensions grooving machine before sealing the cap
welding • +/- 0.1 mm grooving accuracy • Free 100 pcs sample of selected die
• > 1 million times grooving blade durability
RM 19,450 RM 39,270 RM 23,760

MSK-111A  BD-10ML
Semi-Automatic Stacking Bottletop Electrolyte Digital
Machine for Pouch Cell Dispenser with 1 L SS Bottle
• 200 mm max stacking layer • Uses a floating piston design
length with no seals to wear or replace,
• 400 mm fixed travel distance minimizing service downtime
• 1 - 9999 travel cycles • 4 PP bottle adapters, 45/40mm,
• 40 - 80 psi suggested air 45/33mm, 33mm/28,
pressure 33mm/24 and filling tube
• Stacking platform consists • One 1000 mL stainless steel
of 550 mm L x 390 mm W x bottle
660 mm H
RM 20,196 RM 2,750

8 KGC RESOURCES
MTI USA

MSK-AFA-III MSK-140 MSK-T-10

ADVANCED MATERIAL SCIENCE

Compact Tape Casting Film Coater with Compact Heating Sealer for Sealing Compact Precision Disc Cutter with
Dryer, Vacuum Chuck & Film Applicator Laminated Aluminum Case of Pouch Cells Standard 16, 19, 20 Dia. mm Cutting Die
• 10 - 550 m stroke length adjustable by • Max sealing length up to 190 mm • Cr plated steel as major structural material
using adjustable position switch • Sealing width up to 3.2 mm • 16, 19, and 29 mm precision dies are
• 100 mm adjustable doctor blade • Sealing thickness up to 0.19 - 0.3 mm included
included • 25 mm die opening • Compact size which can be put into glove
• 120 l/m oilless vacuum pump included • 0 - 0.7 MPa adjustable sealing pressure box through air lock chamber
for immediate usage • 50 - 300°C adjustable sealing temperature • Can be customized up to 2mm diameter
• 0 - 100 mm/sec variable traverse speed • 0 - 99 Seconds adjustable heating timer dies
• Max heating temperature is up to 200°C • Soft sealing blade (with tab in between)
RM 36,690 RM 24,288 RM 17,450

VACUUM DESSICATOR
 EQ-SP-VC-3
Vacuum-able Dessicator with Internal Pump
• 11 liter capacity with inside dimension of 320 W x 240 D x 260 H mm
• Delicate apperance with solid and rigid structure made of high intensity polycarbonate
materials
• Dust, mildew, and moisture proof
• Can be operated without a power supply and design is free of fragile moisture absorption
reading electronics
RM 1,800

SCREEN PRINTING COATER

 EQ-SPC-2
Desk-top Screen Printing Film Coater
• Dia. 150 mm sample stage
• One Vacuum Chuck & One 120 l/m Oilless Vacuum Pump are included for quick usage
• Screen frame adjusting: 20° adjustable
• Vacuumed area: 10 x 10 mm
• Max. 155 x 255 mm printing area
RM 13,480

VACUUM GLOVE BOX

 EQ-VGB-2Y
Bench top Transparent Glove Box with Pressure Control System
• Transparent polycarbonate main chamber casing with dimensions: 875(L)x480(W)x500(H) mm up
to 675 Torr vacuum level
• Air-lock chamber with dimensions: 230(L)x220(W)x230(H) mm up to 100 Torr vacuum level
• One mechanical vacuum gauge and two solenoid valves are installed for pressure control
• Two needle valves for main chamber and air-lock chamber are installed for immediate use
• One pair of Latex Gloves are included for immediate use
RM 13,300

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 9

 MTI USA

FURNACE & GLOVE BOX ACCESSORIES

EQ-TW-3A EQ-2XZ EQ-YTP-550-LD

Single Step Rotary Vane Vacuum Pump Double Stage Rotary Vane Vacuum Pump Heavy Duty Double Stage Rotary Vane
Vacuum Pump
• 187 liter/min • 120 liter/min • 220 liter/min
• Vacuum up to 0.075 Torr • Vacuum up to 0.004 Torr • Vacuum up to 0.003 Torr
• 1/2 HP 360 W • Traps particles up to 0.3 microns • 550 W (atm)
• 20 ml volume of oil • With Oil Trap, Exhaust Filter, Bellow & • With Exhaust Filter, KF25D Adaptor and
• Oil Mist Reduction Unit with KF-25 KF-D25 Inlet Clamp
ADVANCED MATERIAL SCIENCE

Adapter and Quick Clamp are included

RM 3,825 RM 8,250 RM 12,580

EQ-VPC-30D EQ-VPC-30 EQ-OM-OS524E

Dual Valve Digital Vacuum & Pressure Gauge In-Line Digital Vacuum Pressure Controller Hanheld Infrared Thermometer with Laser
Pointer
• Range up to 800 Torr • Range up to 800 Torr • Measurement range from 538°C -
• +/- 0.25% full-scale • +/- 0.25% full-scale 2482°C
• Measurement in: psia, psig, mm Hg, “ Hg, • Measurement in Torr • Built-in Laser sighting in Circle & Dot
“ H20, mBar, Atm, Torr, kPa • For clean, dry, noncorrosive and inert configurations
• For clean, dry, noncorrosive and inert gas gas • 100 ms response time
• 1/8” NPT female connection • 1/8” NPT female connection • Spectral response within 2 to 2.5 microns

RM 11,620 RM 8,750 RM 11,580

EQ-MTM-3  EQ-MTS02
Three Channels Temperature Temperature Control System for
Monitoring System MTI Furnace via Computer
• Computerized via an RS232 • Can be used for MTI furnaces
comm port (cable included) with 518P controller except
• Three buzzing alarms GSL-1100X-S, KSL-1200-S
• Accept K, S and B type of and OTF-1200X-S.
thermocouple • One control module, serial
• Cut off power function when port controller cable and one
temperature exceeds the set disc of software package are
point included
RM 11,580 RM 1,089

10 KGC RESOURCES
MTI USA

GPH-DHDO EQ-MTC-C4 EQ-MTC-A5 EQ-MTC-Z3

ADVANCED MATERIAL SCIENCE

PPM Grade Dual Column Inert WK518P Temperature Control Single Zone Precision Three Zone Precision
Gas Purifier Unit Temperature Control Unit Temperature Contol System
• Built-in Regeneration Heater • The controller uses PID via • The controller uses PID via • The controller uses PID via
which can be heated up to SCR power control with 30 SCR power control with 30 SCR power control with 30
300°C segments programmable. segments programmable. segments programmable.
• It removes H2O, O2, CO, CO2, • Designed for lab furnaces • Designed for precision control • Designed for precision control
H2 and NMCH’s to <0.1 ppm heated by resistant wire, SiC high temperature furnace three zone tube furnace from
from any 99.9% purity inert and MoSi2 elements up to from 1000°C - 1500°C with 100°C - 1500°C with heating
gas. 1800°C at Max 4KW heating elements of resistant elements of resistant wire or
• Max pressure up to 0.5 MPa • Accept J, K, T, E, N, B, R and wire or SiC SiC.
• Max flow rate up to 400 mL/ S thermocouple input • Accept K, S, R, J, B, C and D • Accept K, S, R, J, B, C and D
min thermocouple input thermocouple input
RM 12,320 RM 5,600 RM 8,850 RM 29,403

EQ-CGM-2F EQ-GSL-3F-SS EQ-W3000 EQ-RH-800

Two Channel Trace Gas Mixer Gas Mixing Control Station Trace Oxygen Analyzer Precision Humidity Analyzer
• Two Flowmeter with flow rate • Three Channel Flowmeter and • KF40 Connector is provided • KF25 Flange is provided
range from 16 to 160 mL/min Valves are provided • Three auto-ranging scales • Measure humidity level up to
• Mechanical Pressure Gauge • To control up to 3 gases available: 0.01 ppm to 3000 999.9 ppm
(mixing tank): 0 - 1.0 MPa, flowing through vacuum ppm • Working pressure range is
(0.02 MPa/grit) sealed MTI tube furnaces • ZrO2 fuel-cell as the oxygen 0.1 Pa - 30 MPa
• Three Pipe fittings for 1/4” • Mechanical Pressure Gauge sensor • Gas flow rate range is 1-5 lpm
pipe (nylon or stainless steel) (mixing tank): -0.1-0.15 MPa, • Max pressure up to 90 psi •Alarm signal when higher than
• No power required (0.01 MPa/grit) • Up-limit and low-limit alarm 20 mA or lower than 4 mA
signal programmable
RM 5,800 RM 18,780 RM 16,800 RM 17,495

EQ-RH-606B EQ-GD-01
Humidity & Temperature Monitor Laboratory Gas Drying Unit
• Alarm can be set based on • Max working pressure: 90 psig
requirement • Max efficiency at 0.1 scfm
• Detachable Probe and KF25 • 50 grams of water capacity
feedthrough are provided • Inlet and outlet connectors
• Temperature range: 0°C- are SS 1/8” NPT female
80°C fittings wih molded
• Humidity range: 2%RH to polycarbonate column.
95%RH • Indicating dessicant turns
• Accuracy: ±3%RH blue when active and turns
• Sensor cable length: 3 meters pink when exhausted
RM 1,580 RM 1,369

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 11

 MTI USA

LABORATORY MILL
MSK-SFM-1 MSK-SFM-3 MSK-SFM-8

MSK-SFM-2

MSK-SFM-5
MSK-SFM-12M
Dimension
Model Speed (rpm) Features Price
L x W x H (mm)
MSK-SFM-1 Main plate: 450 x 490 x 530 • Granularity can be as small as 0.1 micron
30 -350 • Digital display speed in rpm
Mixing tank: • Timer controls major platen’s running time from 1 - 999 min
RM 31,806
0 - 300 • Timer control tank rotation time from clockwise to
anticlockwise direction from 1 - 99 min
ADVANCED MATERIAL SCIENCE

• 4 alumina jars with various size of YSZ mill balls are included
MSK-SFM-2 Main plate: 450 x 490 x 530 • Granularity can be as smaller than 0.5 micron
0 -100 • Three dimensions rotation: major platen, individual tank and
Mixing tank: up-down gravity
60 - 700 • Digital display the speed of tank rotation in rpm
RM 19,905
• Running time can be set from 1 - 999 min
• Four 1000 ml nylon jars, water-proof by rubber O-ring are
included
• Four sets of agate milling balls included (96 balls in total)
MSK-SFM-3 1200 405 x 365 x 260 • Granularity can be as small as 0.1 micron
• Timing range from 0 - 120 min
RM 15,750
• One 50 ml alumina jar with one set Zirconia mill balls are
included
MSK-SFM-5 0 - 1200 700 x 600 x • Granularity can be as small as 1 micron
1100 • 5 liter stainless steel container with water cooling jacket
RM 14,150
• Programmable controller to set time, speed and rotation
direction
MSK-SFM-7 320 330 x 300 x 530 • To produce coating slurry by mixing small batch of chemical
and compound under vacuum to remove gas bubble and protect
sample from oxidation
• Built in vacuum pump with -0.08 - 0.09 MPa RM 15,378
• Vibration plate frequency at 1 kHz
• One 150 ml stainless steel and one 500 ml aluminum
container are included
MSK-SFM-8 Mortar: 240 x 240 x 500 • Granularity can be as small as nanometers
0 -10 • 5” agate mortar and agate head pestle
Pestle: • Grinding pressure is adjusted by spring RM 12,830
0 - 80 • Grinding time can be set according to using the automated
controller
MSK-SFM- 2700 - 4000 170 x 210 x 135 • 3 x 2.0ml tube can be loaded on the device simultaneously
12M • Timer can be set within 3 sec to 3 min
• Two types of Pure High Impact Zirconia Beads are included for
rapid milling RM 4,350
• The optimized mixing motion causes rapid milling through
constant high velocity impact from the hardened micro-beads
chosen

12 KGC RESOURCES
TORREY HILLS USA

THREE ROLL MILLS

Advantages of Torrey Hills Three Roll Mills:
• Three roll mill rollers are precision ground 420J2 stainless steel to prevent rust or erosion. The
hardness is rated at HR50-60 for reliable long-life usage.
• Rolls are cored for either cooling for heating. Manifold, valve, and collection tank are standard.

ADVANCED MATERIAL SCIENCE

• Rollers are ground to 5um concentricity and 0.5um surface finish for precise applications
• Higher throughput than most competitors’ models
• Variable speed control allows adjustable/slower speed runs
• Emergency pull cord on top of the machine as an extra safety feature
• Roller spacing and adjustment is set manually with quick engagement mechanism by the use
of four small hand wheels.
• Gap spacing easy to adjust, and remains consistent throughout operation

Model T65 Lab Model

T6x12 Three Roll Mill Model
*The Workhorse*
Roller Material Stainless Steel or Ceramic Hardened Cold Cast Steel
Diameter of Roller 65 mm 142 mm
Length of Roller 127 mm 305 mm
Roller Speed Ratio 1:2:4 1 : 2.35 : 5.4
Speed of Roller 0 - 108 (Slow Roller); 40 (Slow Roller);
0 - 216 (Mid Roller); 94 (Mid Roller);
0 - 432 (Fast Roller) 217 (Fast Roller)
Motor Power 0.55 kW 2.2 kW
Dimensions 635 x 280 x 381 mm 840 x 840 x 890 mm
Price RM 33,850 RM 63,350

HANTECH KOREA

FURNACE

Box Furnace Atmosphere Box Furnace Atmosphere Box Furnace

C-14P M-A15P M-A1400
• Temp: Max 1000°C • Temp: Max 1100°C • Temp: Max 1400°C
• Volume: 3 liter • Volume: 4.5 liter • Volume: 1.5 liter
• Heater: Kanthal A1 Molding Heater • Programmable PID controller • Programmable PID controller
(Heated on three sides) • Quartz tube: 50 (O.D)/46(I.D) x 300(L) • Mullite tube: 53 (O.D)/45(I.D) x 300(L)
• Programmable PID controller mm mm
• Dimension: 300 x 460 x 390 mm • Dimension: 300 x 460 x 390 mm • One side blocked type tube
• Heater: SiC Heater (U type)
• Gas mask, gas port, end mask
• Dimension: 430 x 670 x 460 mm

RM 4,850 RM 9,850 RM 19,780

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 13

 BERKELEY SCIENTIFIC USA

TUBE FURNACE
BSG-1200X BSO-1200G

Multi-position Mini Tube Furnace Split-able Mini Tube Furnace

• Quartz tube, thermal blocks, silicone o-rings, and stainless steel vacuum sealing flanges are included for quick usage
• Max heating rate is up to 20°C/min
• Quartz tube can stand heat until 1200°C
• High purity alumina fiber insulation with heavy duty case
RM 9,980 RM 9,980

MUFFLE FURNACE
ADVANCED MATERIAL SCIENCE

Chamber
Heating Working Heating
Model Dimension Volume Price
Rate Temp Element
LxWxH
Cont: Resistance
BSK-1200X 12” x 8” x 5” 7.2 L Max: 20°C /min RM 10,800
1100°C Wire
Cont: Resistance
BSK -1200X-SU 8” x 8” x 8” 8L Max: 20°C /min RM 18,780
1100 °C Wire
Cont:
BSK-1700X-XS 6” x 6” x 7” 4.2 L Max: 20°C /min MoSi2 Rod RM 27,800
1650 °C
BSK-1200X Cont:
BSK -1700X -M 6” x 6” x 6” 3.5 L Max: 20°C /min MoSi2 Rod RM 22,380
1650°C
Cont:
BSK -1700X -S 4” x 4” x 4” 1L Max: 20°C /min MoSi2 Rod RM 16,320
1650 °C

BSK-1200X-SU

VACUUM OVEN
BS-DZF-6020
Model BS-DZF-6020 BS-DZF-6050 BS-DZF-6050A
Max Working
Ambient - 250°C Ambient - 500°C
Temperature
Capacity 25 Liter 53 Liter
Chamber Dimension 12” x 12” x 11” 16.3” x 13.5” x 14.5”
Features • The chamber is designed with stainless steel and welded with bracing
pieces
• A good vacuum seal is achieved by silicone door gasket and positive latch
door
• Vacuum port and gas inlet are installed to create gas environment in the
chamber
Price RM 5,480 RM 6,450 RM 7,800
BS-DZF-6050A

14 KGC RESOURCES
BERKELEY SCIENTIFIC USA

LED DRY CABINET

• Suitable for storing: photographic & optic lens, cameras or digital photography, audiovisual, precise instruments, food, paper materials,
films, chemical and medical materials, etc.
• Slip layer board make the interspaces adjustable.
• Energy saving design: low electricity consumption resurgence, no heating, no condensation dripping, absence of fan noise

ADVANCED MATERIAL SCIENCE

BS-DC-FCM60 BS-DC-FCM80
BS-DC-FCM100
BS-DC-FCM120

Dimension
Model Capacity Features Price
L x W x H (mm)
BS-DC-FCM60 65 Liter Outer: • Humidity range: 20-60%RH
400 x400 x 475 mm • 1 pcs of shelves
Inner: • Humidity adjustable, energy saving design, digital LED
398 x 375 x 400 mm display and control
RM 920
• 1.0mm thick steel body, rustproof paint, 4mm
toughened glass, import sensor
• Moisture absorbs continuously with sustention for 24
hours
BS-DC-FCM80 84 Liter Outer: • Humidity range: 20-60%RH
400 x400 x 620 mm • 2 pcs of shelves
Inner: • Humidity adjustable, energy saving design, digital LED
398 x 375 x 545 mm display and control
RM 1,280
• 1.0mm thick steel body, rustproof paint, 4mm
toughened glass, import sensor
• Moisture absorbs continuously with sustention for 24
hours
BS-DC-FCM100 115 Liter Outer: • Humidity range: 20-60%RH
400 x400 x 760 mm • 2 pcs of shelves
Inner: • Humidity adjustable, energy saving design, digital LED
398 x 375 x 685 mm display and control
RM 1,880
• 1.0mm thick steel body, rustproof paint, 4mm
toughened glass, import sensor
• Moisture absorbs continuously with sustention for 24
hours
BS-DC-FCM120 128 Liter Outer: • Humidity range: 20-60%RH
400 x400 x 865 mm • 3 pcs of shelves
Inner: • Humidity adjustable, energy saving design, digital LED
398 x 375 x 790 mm display and control
RM 2,100
• 1.0mm thick steel body, rustproof paint, 4mm
toughened glass, import sensor
• Moisture absorbs continuously with sustention for 24
hours

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 15

 BERKELEY SCIENTIFIC USA

BATTERY ANALYZER

Model Features Price

• An eight-channel battery analyzer to analyze small coin cells and cylindrical batteries from
0.002 mA to 1 mA, up to 5V
BS-CT-3008-5V3A • Provides most applications in battery testing fields such as electrode materials research, RM 6,800
battery performance test, small-scale battery formation, capability grading, battery pack
testing and etc
• An eight-channel battery analyzer to analyze small coin cells and cylindrical batteries from
0.1 mA to 10 mA, up to 5V
BS-CT-3008-5V1MA • Provides most applications in battery testing fields such as electrode materials research, RM 7,800
battery performance test, small-scale battery formation, capability grading, battery pack
ADVANCED MATERIAL SCIENCE

testing and etc

• An eight-channel battery analyzer to analyze small coin cells and cylindrical batteries from
6.0 mA to 3000 mA, up to 5V
BS-CT-3008-5V10MA • Provides most applications in battery testing fields such as electrode materials research, RM 7,500
battery performance test, small-scale battery formation, capability grading, battery pack
testing and etc

MASS FLOW CONTROLLER

 BS-MFC-1
• Supply voltage: DC15V / 0.5A • Working pressure range: 0.1 - 0.5 MPa
• Accuracy: ± 2% FS • Program features: multi-segment program set flow
• Output signal: 4 - 20mA rate (configurable)
• Control accuracy: ± 1% FS (CC) • Working temperature: -10 to + 50°C
• Computer Interface: RS485 • Interface Type: According to customer’s request
• Linearity: ± 2% FS • Flow range: 0 - 100, 200, 300,500 1000 SCCM
• Zero: Digital Zero (ml / min)
RM 4,700

VACUUM PUMP

Oilless Vacuum Pump Single Stage Vacuum Pump Single Stage Vacuum Pump Two Stage Vacuum Pump
BS-AP-1400V BS-VP160 BS-VP170 BS-VP2200
• 120 l/m pumping speed • 170 l/m pumping speed • 200 l/m pumping speed • 340 l/m pumping speed
• 80 - 100 Torr ultimate • 6.0 CFM • 7.0 CFM • 12.0 CFM
pressure • 150 microns • 150 microns • 15 microns
• Less than 60 dB noise level
RM 1,400 RM 750 RM 970 RM 1,250

16 KGC RESOURCES
GASTECH AUSTRALIA

SINGLE GAS DETECTOR

GASTECH’s new improved ToxiPro has three visual alarm windows for increased worker safety. Even better, each alarm window comes
standard with both high visibility yellow and red alarm LEDs. In a warning condition, the yellow lights will flash and the lights in all three
windows will chase. In a danger condition, the red LEDs will flash and the lights in all three windows will chase. lus, the improved ToxiPro
has an audible alarm that is 10% louder than previous models! It has many alarm features, including an optional vibrating alarm and sound
pattern and set points which are now fully user customizable.

OIL & GAS INSTRUMENTATION

General Features:
• Electrochemical toxic gas sensor or Galvanic oxygen sensor
• Loud two tone alarm rated at 100dB at 10 cm
• Stores latest 20 events, including sensor type, max reading, average reading, start time and stop time
• Continuous real-time gas readings, peak, STEL (if enabled), TWA (if enabled) and time of day readings
• Compact and rugged, clear polycarbonate with TPE overmold
• Automatic zero calibration with integrated self-check program

Toxic Gas- Single Gas Detector with Datalogging & Vibrating Alarm
Model Description Price
54-45-01VD ToxiPro - Carbon Monoxide (CO) RM 2,450
54-45-02VD ToxiPro - Hydrogen Sulphide (H2S) RM 2,450
54-45-03VD ToxiPro - Sulphur Dioxide (SO2 range 0-100ppm) RM 2,980
54-45-09VD ToxiPro - Nitrogen Dioxide (NO2) RM 3,185
54-45-10VD ToxiPro - Hydrogen Cyanide (HCN) RM 3,185
54-45-13VD ToxiPro - Phosphine (PH3) RM 3,185
54-45-18VD ToxiPro - Chlorine (CL2 specific) RM 3,185
54-45-19VD ToxiPro - Carbon Monoxide (CO-H CO Minus) RM 2,920
54-45-21VD ToxiPro - Ammonia (NH3) RM 2,980
54-45-90VD ToxiPro - Oxygen (O2) RM 2,680

MULTI GAS DETECTOR

Real-time readings of up to four gases simultaneously, one button operation and calibration, easy to read LCD display, audible and visual
alarms, event logger, IrDA port, optional sample draw pump, rugged, compact and affordable - MultiPro Gas Detector. There are two optional
battery packs for user to choose which are rechargable Li-Ion version includes charger or Alkaline (3 AA) battery packs.
General Features:
• Meets IPX5 water standard
• Front-mounted LCD displays readings up to 4 sensor channels
• Loud warbling, two-tone alarm rated at 92 dBA at one foot
• True one-button operation including automatic calibration
• Polycarbonate case with overmolded rubber boot
• Automatic zero calibration with integrated self-check program

Multi-Pro Muti Gas Detector with Datalogging & Vibrating Alarm

Model Description Price
54-48-300ADY8 MultiPro Alkaline LEL/O2 RM 3,580
54-48-301ADY8 MultiPro Alkaline LEL / O2 / CO RM 5,275
54-48-302ADY8 MultiPro, Alkaline LEL / O2 / H2S RM 5,275
54-48-314ADY8 Multipro Alkaline LEL / O2 / CO / H2S (Duo-Tox) RM 5,275
54-48-300NYD8 MultiPro Li-Ion LEL/O2 RM 5,750
54-48-301NYD8 MultiPro Li-Ion LEL / O2 / CO RM 5,750
54-48-302NYD8 MultiPro Li-Ion LEL / O2 / H2S RM 5,750
54-48-314NYD8 MultiPro Li-Ion LEL / O2 / CO / H2S (Duo-Tox) RM 5,750
54-48-314NYDV8 MultiPro Li-Ion LEL / O2 / CO / H2S (Duo-Tox) : Value Pack RM 8,680

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 17

 IMR USA

COMBUSTION GAS ANALYZER

The IMR1000 is a hand held pocket size stack gas analyzer for combustion tests on boilers, burners and etcetera.
General Features:
• Rugged plastic case with protective boot and magnet
• Fuel types to be analyzed are Natural Gas, Propane, Butane, LPG and Light Oil
• Parameters measured are Oxygen, Carbon Monoxide, Carbon Monoxide (ambient), Nitric Oxide and Flue-Gas
Temperature
• Calculated values are Combustion Efficiency, Excess Air, Carbon Dioxide and CO corrected to 0% O2
• Measuring units for the analyzer are ppm and mg/m3
• The analyzer operating condition is within 0 - 40°C, 10 - 90% RH, non-condensing
• Thermocouple Type K as gas sampling probe with (0.25” diameter, 9” length with 9 ft hose length
• Battery operated (4 x AA)

Model IMR1000-3 IMR1000-4

Gas • O2 : 0 -21% with resolution 0.1% / ±0.2% • O2 : 0 -21% with resolution 0.1% / ±0.2%
Measurement • CO : 0 - 4000 ppm with resolution 1 ppm/±10 • CO : 0 - 4000 ppm with resolution 1 ppm/±10 ppm <
ppm < 100 ppm 100 ppm
• CO2 : 0 -30% with resolution 1.0% • CO2 : 0 -30% with resolution 1.0%
• Efficiency: 0 - 99.9% with resolution 0.1% • Efficiency: 0 - 99.9% with resolution 0.1%
• Excess Air : 0 - 250% with resolution 0.1% • Excess Air : 0 - 250% with resolution 0.1%
• CO/CO2 : 0 - 0.999% with resolution 0.0001% • CO/CO2 : 0 - 0.999% with resolution 0.0001%
OIL & GAS INSTRUMENTATION

• NO : 1 ppm/±2 ppm < 30 ppm with resolution ±5 ppm >

30 ppm
Price RM 6,598 RM 10,650

Model IMR1400 Portable, continuous measuring flue

gas analysis instrument housed in
General • Illuminated display with simultaneous display of 8 measured variables an aluminum case for measuring air
Features • Printout of all measured and calculated parameters temperature, flue gas temperature,
• Gas sampling probe, length 10.5” (270mm),NiCrNi, flexible hose 11.5 Oxygen O2, Carbon monoxide CO (H2
ft. (3,5m) comp.), Nitric oxide NO, Nitric dioxide
• Combustion air probe, length 5” (130mm), line 11.5 ft. (3,5m) NO2, Sulfur dioxide SO2, Hydrocarbon
• 7 programmed and 5 programmable fuels HC, losses, excess air, combustion
• Automatic and manual CO overflow shut-off efficiency, draft, Carbon dioxide CO2
• Operating temperature 50°F..104°F (10°C..40°C) and soot. Simultaneous display of eight
• Storing temperature -4°F..122°F (-20°C..50°C) measured parameters on the illuminated
• Interface RS 232 LCD. Integrated thermal printer and
• Dimensions width: 16”(425mm) x 7”(185mm) x 11”(290mm) RS232 interface. Measurement printout
Technical • O2, Oxygen 0-21% or service printout, both include date,time
Data • CO2, Carbon dioxide and fuel type. ppm,mg,mg/kWh,mg(ref.
• CO, Carbon monoxide 0 - 2000 ppm O2) units are selectable. Automatic and
• NO, Nitrogen oxide 0 - 2000 ppm manual CO-bypass. Memory for 220
• NO2, Nitrogen dioxide 0 - 100 ppm measurements. Case has additional
• SO2, Sulfur dioxide 0 - 4000 ppm space for spare parts.
• HC, Hydro Carbon 0- 100% LEL
• TG Gas temperature: -20°C..1200°C
• TA Air temperature: -20°C..120°C
• Combustion Efficiency: 0-99,9 %
• Lambda/excess air 1,0-9,99
• Losses 0- 99.9%
Price RM 19,650
Please contact us for specific gas measurement range for exact price according to your
requirement:
IMR 1400 P O2, CO
IMR 1400 PL O2,CO, NO
IMR 1400 PS O2, CO, NO, SO2 IMR1400
(NO2 or HC instead of SO2)

18 KGC RESOURCES
IMR USA

Model IMR2800
General • Latest sensor technology for a more accurate measurement and
Features longer life time
• Improved interior design for easier service and better unit

OIL & GAS INSTRUMENTATION

protection
• Continuously and simultaneously measuring up to 18 parameters
• Larger display for a better reading
• Portable combustion gas analyzer housed in a rugged aluminum
case IMR2800
• Simultaneous measurement of O2 Oxygen NO2 Nitrogen dioxide
• 23 Fuels are programmed – 4 fuels are programmable
• Automatic zero calibration
• Integrated self-check program
• Simultaneous display parameters on the illuminated display
• Printer with programmable print out cycles
• Standard deviation and average value calculation
• Draft measurement with optional upgrade for differential draft and
velocity measured with a Pitot tube
• Unit selection : ppm – mg/Nm3 – mg/Nm3(ref O2)
• Gas sampling probe E – length 0.8 ft (250mm), hose 8 ft (2.5m)
• Rechargeable battery with charger
Gas • O2, Oxygen 0 - 21%
Measurement • CO2, Carbon dioxide 0 - CO2 max (calculation)
• CO2, Carbon dioxide 0 - 20% (NDIR)
• CO, Carbon monoxide 0 - 2000/4000 ppm or 0-10/20 Vol. %
• NO, Nitrogen oxide 0 - 2000 ppm Please contact us for specific gas
• NO2, Nitrogen dioxide 0 - 100 ppm measurement range for exact price
• NOx, Nitrogen oxide 0 - NOx max according to your requirement
• SO2, Sulfur dioxide 0 - 4000 ppm
• HC, Hydrocarbon 0- 100% LEL
• NH3, Ammonia 0 - 1000/5000 ppm
• HCl, Hydrogen Chloride 0 - 200 ppm
• H2, Hydrogen 0 - 10000 ppm
• Cl2, Chlorine 0 - 5000 ppm
• Draft - 40 to + 40 hPa
• Lambda/excess air 0-999%
• Losses 0- 99.9%
Price RM 27,340

HTA ITALY

LIQUID AUTOSAMPLER
Model HT300A
Features • 110 positions rotating tray for 2 or 2.5 ml vials
• Supports the use of 4 solvent vials of 10 ml each
• Can be controlled by keypad or by PC using software
• Hot and cold needle injections (Dual simultaneous injections)
• Small volume, Priority, Ambient headspace and Multi phase Sampling available
• Handle up to 100µL syringe volume
• Injection speed up to 100µL/sec
• Bubble elimination up to 15 pull up strokes
Price RM 34,000

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 19

 BE MARUBISHI JAPAN

BENCH TYPE BIOREACTOR

BE MARUBISHI’s Photo Bioreactor was especially designed for cultivation of
microalgae and callus. Fine bubbles from 30 micron stainless fiber filter creates
high gas transfer coefficient. The low shear stress homogenization system makes
vertical circulation flow minimalizing damage to cells. The highly effective lighting
system stimulates photosynthesis.
BIOTECHNOLOGY & LIFE SCIENCE

MDFT-µ MDFT-500
Micro Fermentor MDFT µ100/100 mL Eco Desk-Top Fermentor 5 L

• Suitable for minimum volume fermentation • The vessel made of Pyrex glass, heat resistance, and
• The vessel made of Pyrex glass, heat resistance, and autoclavable autoclavable
• Silicone made upper head cap • Impeller type turbine, fullzone, and paddle complete with baffle
• Magnet stirrer with DC brushless motor give accurate speed for enhanced mixing
control • Temperature control by silicone rubber heater and cooling water
• Air supply with single nozzle sparger, flow meter, and 0.22 µ air • Air inlet to the vessel pass filter size 0.2 micron through air
filter sparger and control by rotameter type needle valve
• 6 mm dia. pH and DO electrode can be installed • 4-20 mA for recorder output
• Recorder output for temperature and stirring speed • Agitation system is sealed by mechanical seal or non-sealed
• Temperature control by silicone rubber heater and cooling pipe magnetic driving system
• Compact shape console saves space- • Both internal and external electropolish grinded No. 300 buff
RM 26,350 RM 24,750

Multi Channel Indicator/Controller for pH, Dissolved Oxygen & Anti Foam
Model MCI-6C
Features • Measurement in ppm, mg/l or % saturation
• Two 0/4….20mA current output, galvanically isolated
• Password protection against accidental parameter change
• Pressure and Salinity input for automatic correction
• Pulse length or pulse frequency proportional control
• Integrated PI controller, pulse length or pulse frequency
• Two relay as limit contact with on/off delay timer
• One relay as alarm contact and one relay as wash contact
Application Areas • D.O. Range: Saturation 0-500%; COncentration 0-20 ppm
• D.O. Accuracy: 0.5% of measured value
• pH Range: -1 to 15 pH
• mV Range: -1500 to +1500 mV
• pH/mV Accuracy: 0.03 pH/62 mV
• Temperature Input: PT100/PT1000 (jumper selectable)
• Current Putput: 2x0/4-20 mA
• Control Function: PI Controller; Pulse length & pulse frequency
Price RM 32,750

20 KGC RESOURCES
BE MARUBISHI JAPAN

INTELLIGENT BIOREACTOR
BIONEER SERIES
• PI, HA/LA or PID control ensures accuracy
• 8 control channels (6 standard & 2 optional channels)

BIOTECHNOLOGY & LIFE SCIENCE

• DO cascade control with thermal mass controller (optional) & selectable control order
• Graphic chart indication for process value of respectively control items
• Indication for total output time of addition pump
• Electrode checking function for pH & DO
• Diagnosis function for system breakdown
• Memory card for all control data
• Troubleshooting by conversation help function
• 10 steps program control
• Built-in sampling timer for optional auto-sampler
• RS-232 port as standard & LAN port as optional
GRAPHIC PANEL BIONEER-5N

R & D SCALE FERMENTOR

MSJ SERIES
(10, 20, 30, 40, 50,70 & 90 L)

All surfaces in product contact are fabricated from SS316 material.

All internal and vessel welds are ground smooth & mechanically
polished. All interior surfaces are polished to Ra<0.2 micron. Either
top entry or bottom entry driving system is available with double
mechanical seal. Versatile use for microbes with standard & plant
tissue or mammalian cell with special modification. Flexible design
suit to the the condition of customer’s installation site. Either modular
type controller or multi-channel BIO-Process control (MDIAC-S6) will
meet various kind of demand for measurement & control of culture
condition. Computer coupling with the MDIAC-S6 enable intelligent
control system construction.

PILOT PLANT FERMENTOR

The process control system has the
following items:

• Temperature of the internal measurement

• pH measurement
• Dissolved oxygen measurement
• Agitation speed measurement
• Air flow rate measurement
• Carbon dioxide flow rate measurement
• Vessel pressure measurement
• ORP measurement and indication
• Drain pipe end temperature measurement
• Sterile piping header pressure

MPF SERIES
(100, 200, 300, 400, 500 L - OTHER SIZE AVAILABLE UPON REQUEST)

All surfaces in product contact are fabricated from SS316 type. All internal and vessel welds are ground smooth & mechanically polished.
All interior surfaces are polished to Ra<0.2 micron. Either top entry or bottom entry driving system is available with double mechanical seal.
Versatile use for microbes with standard & plant tissue or mammalian cell with special modification. Flexible design suit to the the condition
of customer’s installation site. Bioprocess automatic operation & control system (BPACS) are used to control temperature, pH, agitation
speed and other parameters, which for automation control are sterilization, medium transfer, and others. A graphic touch panel is used by
operator to control system’s data display, parameter setting & switching operation.

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 21

 QUANTEK INSTRUMENTS KOREA

O2 & CO2 ANALYZERS

Model 901 Model 902D Model 902P Model 905 Model 906 Model 907
Model 901 Model 902D Model 902P
Headspace Oxygen Analyzer Headspace Oxygen/Carbon Dioxide Analyzer Oxygen/Carbon Dioxide Analyzer
Primarily used for the measurement Primarily used for testing modified atmosphere Primarily used for research processes, gas
of residual oxygen in gas-flushed food packages and other containers blending, biotech and other system
packages
• Measuring range from 0.0 to 100% O2 • Miniature diaphragm pump with 5cc/sec • Miniature diaphragm pump with 5cc/sec
• 0.1% O2 resolution flow and 2 - 12 sec adjustable timer flow and 2 - 12 sec adjustable timer
• Using proprietary electrochemical cell to • 12” length of double reinforced sample • Front panel fitting with luer connection for
sense O2 prob with exhaust port vents to air disposable filter and exhaust port vents to
• Internal pump that draws 5cc/sec with • Dimensions of 249 x 102 x 254 mm air or tube outlet for recirculation to close
2 - 12 sec adjustable timer • Can be used for food analysis such as system
• Battery operated (Four ‘AA’ NiMH meats, diary products, snack foods, baked • Dimensions of 249 x 102 x 254 mm
rechargeable batteries) foods, prepared meals, coffee, pet food • Can be used in bioreactor systems, gas
BIOTECHNOLOGY & LIFE SCIENCE

• Dimension of 200 x 100 x 40 mm and etcetera blending systems, fruit storage areas,
• Included Consumables: fermentation, biofuel experiments, algae
200 foam septas, 2 luer fit needles, 2 Oxygen Channel offgas analysis and etcetera
particulate filters, 2 liquid block filters • Proprietary electrochemical cell as sensor
• Can be used for food analysis such as • O2 ranges from 0 - 100% Oxygen Channel
meats, diary products, snack foods, • 0.1% O2 resolution • Proprietary electrochemical cell as sensor
baked foods, prepared meals, coffee, • O2 ranges from 0 - 100%
pet food and etcetera Carbon Dioxide Channel • 0.1% O2 resolution
• Solid-state Infrared cell as sensor
• CO2 ranges from 0 -20% or 0 - 100% Carbon Dioxide Channel
• Solid-state Infrared cell as sensor
• CO2 ranges from 0 -20% or 0 - 100%
RM 9,900 RM 15,350 RM 21,380

Model 905P Model 906 Model 907

Oxygen Analyzer for Process & Research Carbon Dioxide Analyzer for Process & Research Portable Oxygen/Carbon Dioxide Analyzer
Primarily used for the measurement Specifically designed for continuous or spot Portable device that can be used for research
of residual oxygen in gas-flushed food check measurement of CO2 levels applications or package testing
packages
• Measuring range from 0.0 to 100% O2 • CO2 ranges from 0.0 to 100% • Miniature diaphragm pump with 5cc/sec
• 0.1% O2 resolution (Other Ranges: 0 to 1%, 0 to 2.5%, 0 to flow and 2 - 12 sec adjustable timer
• Proprietary electrochemical cell as sensor 10%, 0 to 20%, 0-30%, 0-50%) • 12” length of double reinforced sample
• Internal pump that draws 5cc/sec with • Infrared (NDIR) as sensor; non depleting prob with exhaust port vents to air
2 - 12 sec adjustable timer wih no moving part • Dimensions of 203 x 51 x 178 mm
• Internal rechargeable 12 VDC battery • Internal rechargeable 12 VDC battery • Can be used for food package
• Internal rechargeable 12 VDC battery • Internal pump with on-off switch on front applications and reseach & industrial
• Dimensions of 249 x 102 x 254 mm panel that draws about 5 cc/sec applications
200 foam septas, 2 luer fit needles, 2 • Dimensions of 254 x 106 x 266.7 mm
particulate filters, 2 liquid block filters • Male connectors, filters, T style connector, Oxygen Channel
• Can be used for food analysis such as inlet fitting, screwdriver, rubber washers, • Proprietary electrochemical cell as sensor
meats, diary products, snack foods, 60 cc syringe for sample injection and • O2 ranges from 0 - 100%
baked foods, prepared meals, coffee, PTFE .456 micron are provided • 0.1% O2 resolution
pet food and etcetera • Can be used in bioreactor systems, gas
blending systems, fruit storage areas, Carbon Dioxide Channel
fermentation, biofuel experiments, CO2 • Solid-state Infrared cell as sensor
mitigation reseach and etcetera • CO2 ranges from 0 -20% or 0 - 100%
RM 18,980 RM 18,980 RM 6,950

22 KGC RESOURCES
HEB CHINA

JACKETED GLASS REACTOR

HEB’s cylindrical glass reactor is an ideal device in synthetic chemical, biological, pharmaceutical and etcetera. Liquid circulation of hot,
cold or cryogenic can be filled into the jacket of the reactor. Substance reacts by stirring under normal or negative pressure in airproof glass
container. Reaction process can be watched clearly through crystal reaction flask. This equipment is very suitable in library experiment or
medium-production in modern biology and pharmacy. It is also applied in synthesizing materials in fine chemical industry.

BIOTECHNOLOGY & LIFE SCIENCE

General Features:
• Integrated jacket reaction flask has big caliber with
good seal and high strength
• Professional PTFE cover supports high speed stirring
HEB-2L in vacuum
(WATER BATH & • Three standard mouth can be used for multi-purpose
CHILLER ARE NOT according to customer needs. Standard fittings
INCLUDED) are charging cork, thermometer tube and reflux
condenser.
• Converting-frequency adjustable speed for AC motor
with constant rotating speed, no brushless, no sparkle,
safe, stable and can continuously working for hours
• The glass is made from GG17 high quality silicone
material which owns good chemical-physical
attribute.
• Stainless steel frame which is fasten using three-joint
hardware that will not shake when the user is running
HEB-100L an experiment

Overall Dimension Flask

Model Volume Rotation Speed Torque Power Price
LxWxH Necks
HEB-1L 35 x 27 x 65 cm 1L 30 - 1300 rpm 4 pcs 2400 gcm 40 W RM 4,360
HEB-2L 43 x 35 x 100 cm 2L 100 - 1300 rpm 4 pcs 5000 gcm 90 W RM 4,422
HEB-3L 50 x 38 x 95 cm 3L 0 - 1300 rpm 4 pcs 5000 gcm 90 W RM 5,280
HEB-5L 50 x 38 x 105 cm 5L 30 - 1300 rpm 5 pcs 5000 gcm 120 W RM 5,940
HEB-10L 57 x 57 x 180 cm 10 L 0 - 1300 rpm 5 pcs 7200 gcm 120 W RM 9,980
HEB-20L 61 x 41 x 180 cm 20 L 50 - 900 rpm 5 pcs 15000 gcm 180 W RM 12,580
HEB-30L 100 x 105 x 240 cm 30 L 50 - 900 rpm 5 pcs 15000 gcm 250 W RM 14,450
HEB-50L 100 X 150 X 240 cm 50 L 50 - 900 rpm 5 pcs 22000 gcm 370 W RM 15,980
HEB-80L 56 x 74 x 267 cm 80 L 0 - 500 rpm 5 or 6 pcs 22000 gcm 370 W RM 23,760
HEB-100L 88 x 65 x 280 cm 100 L 50 - 900 rpm 5 or 6 pcs 22000 gcm 370 W RM 28,580

HYSC KOREA
COLONY COUNTER
Model HYC-560
Features • 4 digits LED digital display with buzzer sounds for every counting
• Wider view using 125 mm wide lens
• Bacteria can be counted by picking with stainless needle point pen
• 5” Magnifier, Power Cord, 100 mm Dish Holder, Stainless Needle
Point Pen and Marking Pen Probe are included
Specification Petri Dish Holder : Accepts 100 mm dish (removable) and 150 mm (fixed)
Ilumination : Fluorescent lamp
Dimensions: 310 mm L x 290 mm W x 100 mm H
Mode of Counting • Manual push button counting
• Needle-point probing
• Marking pen probing
Price RM 1,720

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 23

 NEW ERA USA

SYRINGE PUMP
DUAL-NE-1000X NE-1000 NE-1600

NE-300 NE-1002X
NE-9000
NEW ERA’s programmable syringe pumps provide an affordable solution
for the sophisticated dispensing and flow control applications. Features
include infusion and withdrawal, computer interface and advanced
programming option.
The programmable syringe pumps can be applied in Chemistry, Tissue Engineering, Nanotechnology,
Electrospinning, Microfluids, Neuroscience, Biology and Physics.
NE-4000

Model Description Infusion Rates Features Price

NE-1000 Single Syringe 0.73 µl/hr to 2100 • Holds 1 syringe from the smallest size available up to 60 cc
Pump ml/hr • 35 lbs. at minimum speed, 18 lbs. at maximum speed
RM 4,800
(1 cc syringe to 60
cc syringe)
DUAL-NE- Continuous Dual 0.73 µl/hr to 2100 • Holds 1 syringe up to 60 cc for each syringe pump
1000X Syringe Pump ml/hr • Allow continuous infusion or emulsification
RM 8,980
LABORATORY EQUIPMENT

System (1 cc syringe to 60 • 35 lbs. at minimum speed, 18 lbs. at maximum speed

cc syringe)
NE-1002X Microfluid 0.008 nl/hr to 2545 • Holds 1 syringe up to 140 cc syringe but can only open up
Syringe Pump µl/min to about 120 cc lengthwise
RM 8,320
(0.5 ml syringe to 140 • Advance Per Step: 4.252232 Nanometers
ml syringe) • 100 lbs. at minimum speed, 18 lbs. at maximum speed
NE-1600 Six Channel 0.452µl/hr to 1451 • Holds 2, 4, or 6 syringes of up to 60 cc each
Syringe Pumps ml/hr • 160 lbs. at minimum speed, 30 lbs. at maximum speed
RM 8,320
(1 cc syringe to 60
cc syringe)
NE-4000 Double Syringe 1.459 µl/hr to 7635 • Hold 2 different syringes from the smallest size available up
Pump ml/hr to 60 cc each of variable sizes
RM 5,950
(1 cc syringe to 60 • 100 lbs. at minimum speed, 18 lbs. at maximum speed
cc syringe)

The NE-1000 Family of Syringe Pumps Features:

• Built for automation
• Infuses and withdraws
• Applications range from simple infusions to complex pumping programs
• Operates stand-alone or from a computer with programmable preset protocols
• Program up to 41 pumping phases: change pumping rates, set dispensing volumes, insert pauses, control and respond to external
signals, sound the buzzer.
• RS-232 and TTL logic control interfaces

‘Just Infusion’ Syringe Pump Peristaltic Dispensing Pump

NE-300 NE-9000
• Holds small or big syringes up to 60 ml • Pump from a reservoir through replaceable continuous tubing
• Infuses continuously until the user stop the pump • Continuous pumping up to 900 ml/min
• Variable infusion rate can be changed while pumping • Measured dispenses for production filling of bottles
• Power failure mode allows pump to continue pumping after a • Learn and Repeat™ for quick setup of production dispenses
reset • Slow down mode to improve accuracy of dispenses
• Maximum pumping rate of 1568 ml/hr with a 60 ml syringe • Programmable Phases allowing complex pumping applications
• Does not withdraw, volume target or have computer interface and interaction with external devices

RM 2,230 RM 3,580

24 KGC RESOURCES
NEW ERA USA

SYRINGE HEATER
The syringe heater constantly monitors and displays the temperature measured
on the primary heating pad. While regulating the temperature, the Heat Clamping
will hold the set temperature. Thermo-Kinetic Mode reduces temperature swings
and tightens the Heat Clamping at the set temperature by dynamically adjusting
the heating by reacting to changes in the temperature measurement and rate of
temperature change.

LABORATORY EQUIPMENT
HEATER-KIT-1LG HEATER-PAD2-1LG
HEATER-KIT-1LG HEATER-PAD2-1LG HEATER-PAD3-1LG
Syringe Heater Kit Control Unit
(Primary Heating Pad with Temperature Secondary Heating Pad Third+ Heating Pad
Sensor)
• Maximum temperature of 185°C
• User adjustable Thermo-Kinetic Heat Clamping for regulation of Set Point temperature
• RS-232 bidirectional control from a computer with built-in RS-232 network driver
• RS-232 network supports up to 100 heaters, pumps & other devices from one PC port
• Power Failure Mode: Restarts the heater Active Mode after a power interruption
• Selectable temperature units of Celsius or Fahrenheit
• Soft power switching for long life
• Non-volatile memory of all operating parameters
RM 1,980 RM 680 RM 680
Syringe pump & syringe are not included with syringe heater.

SYRINGE PUMP SOFTWARE

SyringePumpPro is an easy to use computer interface for programmable syringe pumps. It
permits faster programming and operation of one or more pumps. The user can configure
and control multi-pump protocols, log pump activity and send commands to selected
pumps.

Alternative license examples to purchase SyringePumpPro:

• Connecting 5 pumps to a single computer, at the same time, you will need one 5 pump license
• If you have 5 pumps connected one at a time, to one computer, a 1 pump license will do
• If you need to connect 5 single pumps to 5 separate computers, purchase five 1 pump licenses

Model Description Price

SYRINGE-PUMP-PRO-01 SyringePumpPro Software License for 1 RM 500
SYRINGE-PUMP-PRO-02 SyringePumpPro Software License for 2 RM 900
SYRINGE-PUMP-PRO-03 SyringePumpPro Software License for 3 RM 1,200
SYRINGE-PUMP-PRO-04 SyringePumpPro Software License for 4 RM 1,200
SYRINGE-PUMP-PRO-05 SyringePumpPro Software License for 5 RM 1,600

Flow rates vary with the selection of syringe and the type of motor
and gearing in the pump. The following are example flow rates for a
sample of syringes. Higher flow rates are available.
Syringe Size Maximum Rate Minimum Rate
0.5 µl 25.49 µl/hr 0.001 µl/hr
1 ml 53.09 ml/hr 0.73 µl/hr
5 ml 406.1 ml/hr 5.581 µl/hr
10 ml 600 ml/hr 8.244 µl/hr
20 ml 975.8 ml/hr 13.41 µl/hr
30 ml 1282 ml/hr 17.63 µl/hr
60 ml 2120 ml/hr 29.13 µl/hr

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 25

 HYSC KOREA

WATER BATH
CWB-13M CWB-20M CWB-30M

Shaking Water Bath

Model SWB-25 SWB-35 SWB-55
Capacity 25 L 35 L 55 L
Features • Using Digital PID Controller with LED digital display
• Over temperature cut-off safety
Cooling Bath • heating power up to 2300 W
13 L 20 L 30 L • Temperature ranges from ambient 5°C to 100°C
• Internal material made from Stainless Steel SUS304
1500 W 2000 W 3000 W • Unique design multi rack separable
• Temperature ranges from -10°C to 99°C Price RM 5,850 RM 6,580 RM 7,690
• Using Digital PID Controller with LED digital display
• Magnetic drive circulator pump with max flow rate WD-06
30 l/min
Water Bath
• Refrigerator power: 1/2 HP
• Over temperature cut-off safety • Controller: PID 4 digit LED
• Internal material made from Stainless Steel • Range: Ambient to 100°C
LABORATORY EQUIPMENT

SUS304 • Temperature accuracy: +/- 0.1°C

• Internal: 240 x 140 x 150 mm
RM 8,824 RM 9,668 RM 15,780
• Material: Stainless Steel
• Heater: 500 W
RM 1,858
INCUBATOR
SI-100A SI-100R SI-300R SI-300RF SI-64 SI-150

Shaking Incubator
• Temperature: • Temperature: • No light • Fluorescent • Capacity: • Capacity: DI-42
5°C to 60°C 0°C to 60°C system light system 64 L 150 L
• No • Refrigerator consists of Incubator
refrigerator power 20 W • Fuzzy function to prevent
power overheat
• Accurate temperature control
•Capacity: 100 L • Capacity: 300 L • Door Safety by Digital PID controller
• Krypton light system consists • Refrigerator power: 1/3 HP • Temperature: 5°C to 60°C • Controller select time scale
of 60 W • Temperature: 0°C to 60°C • Alarm audible when timer
end
• Temperature range: Ambient
to 60°C
• Internal: 350 x 350 x 350
• Speed range from 20 - 300 rpm with shaking stroke of 20 mm orbital motion mm
• Internal material made from Stainless Steel SUS304 • Alarm audible when timer
• Over temperature cut-off end
• Using PID digital controller
RM 8,220 RM 9,680 RM 13,950 RM 14,980 RM 7,080 RM 7,920 RM 4,320

26 KGC RESOURCES
SAMHEUNG ENERGY KOREA

ROTARY EVAPORATOR

LABORATORY EQUIPMENT
HS-2005S-N HS-2005V-N HS-2000NS HS-2001NS

Model HS-2005S-N HS-2005V-N HS-2000NS HS-2001NS

Dimension 730 x 410 x 630 620 x 410 x 870 320 x 730 x 520 320 x 580 x 720
(lxwxh mm)
Weight 19.5 kg 19.5 kg 16 kg 17 kg
Condenser Slant type condenser Vertical type condenser Slant type condenser Vertical type condenser
Speed 20 - 280 rpm
Flask Capacity 6 different types of flasks are attachable (from 50 ml to 3000 ml)
Heater Power 1000 W
Bath Capacity 4.3 liter
Temperature Ambient - 180°C
Features • Digital control panel for temperature and speed
• If the amount of water goes down under the certain threshold in the heating bath, the system automatically turns off
its power for the safety purpose
• Included Water Bath HS-3001 with PTFE coating and double jacketed body
Price RM 8,250 RM 8,580 RM 7,260 RM 7,920

WATER BATH
HS-3003 HS-3005N
Cold Trap Bath Cooling Water Circulator Bath
• Consists up to 4 liter • Consists up to 4 liter
• Dimension : 250 x 510 x 510 mm • Dimension: 250 x 510 x 510 mm
• Glass type • Refrigerant: 134 A
• Temperature down to -40°C • Using FND Controller
• Refrigerator power: 1/3 HP • Flow rate up to 15 liter/min
• Refrigerant: 134 A • Temperature down to -20°C
• Using FND Controller • Using FND Controller
• Power consumption up to 334 W • Power consumption up to 334 W
• Applied when the cold trap needs to be • Refrigerator power: 1/3 HP
done in extremely low temperature • Refrigerant: 134 A
• Quick freezing sample for freeze- • Using FND Controller
drying and reaction stop of the enzyme • As a source of cooling to the the
rotary evaporator
RM 5,874 RM 5,220

ASPIRATOR
Model HS-3000
Description Electric Aspirator
Features • Bath is made of polypropylene
• Pump capacity: 18 liter/min x 2EA and bath capacity: 8 liter
• Motor Power 150 W
• Dimension: 320 x 240 x 330 mm
Price RM 2,150

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 27

 MTI USA

ALUMINA CRUCIBLES
Alumina Crucible Low Form 99.6%
Model Top diameter (mm) Bottom diameter (mm) Height (mm) Capacity (ml) Price
AL-1020 35 24 42 20 RM 31.00
AL-1050 48 30 54 50 RM 49.50
AL-1100 58 35 68 100 RM 66.00
AL-1150 66 40 80 150 RM 89.00
Alumina Crucible
Low Form AL-1250 79 42 93 250 RM 108.00
AL-1500 100 60 110 500 RM 178.00

Alumina Crucible Low Form Lid

Model Top diameter (mm) Capacity (ml) Price
AL-1020-LID 35 20 RM 30.00
Alumina Crucible AL-1050-LID 48 50 RM 30.00
Lid AL-1100-LID 58 100 RM 49.00
AL-1150-LID 66 150 RM 55.00

Alumina Crucible High Form

Model Top diameter (mm) Height (mm) Capacity (ml) Price
LABORATORY EQUIPMENT

AL-2010A 25 25 10 RM 33.00
AL-2050A 45 35 50 RM 49.50
AL-2050B 40 45 50 RM 49.50
AL-2100 40 95 100 RM 66.00
Alumina Crucible AL-2250 60 100 250 RM 108.90
Low Form AL-2500 72 148 500 RM 174.90

Alumina Boat Rectangular 99.8%

Model Length (mm) Width (mm) Height (mm) Price
EQL54W38H20 54 38 20 RM 43.00
EQL82W42H23 82 42 23 RM 68.00
Alumina Boat EQL50W40H20 50 40 20 RM 45.00
Rectangular EQL50W20H20 50 20 20 RM 45.00
EQL82-W42H23 82 42 23 RM 43.00
High purity alumina EQL65W88H28 65 88 28 RM 89.00
products can withstand EQL65W65H30 65 65 30 RM 89.00
very high temperature
EQL100W40H18 100 40 18 RM 68.00
under reducing, inert or
high vacuum condition. EQL100W20H20 100 20 20 RM 68.00
Alumina products EQL90W65H30 90 65 30 RM 89.00
can withstand up to EQL150W50H30 150 50 30 RM 275.00
1750°C.
EQL300W40H20 300 40 20 RM 395.00

Alumina Plate Rectangular 99.8%

Model Length (mm) Width (mm) Thickness (mm) Price
AL-P220-220-6 220 220 6 RM 624.00
AL-P150-80-6 150 80 6 RM 226.00
Alumina Plates
AL-P102-25-6 102 25 6 RM 119.00
AL-P90-65-6 90 65 6 RM 119.00

28 KGC RESOURCES
MTI USA

QUARTZ BOAT

EQ-QB-4025S

LABORATORY EQUIPMENT
EQ-QB-0210 EQ-QF-0806
EQ-QB-6025

Quartz boat is made from high purity quartz ( 4N purity) with 1200°C working temperature.
Model Dimension Features Price
EQ-QB-0210 20 x 10 x 8 mm Can fit in MTI GSL-1100X and OTF-1200X-S (1” O.D tube furnace) RM 125
EQ-QB-1017 100 x 17 x 10 mm Can fit in MTI GSL-1100X and OTF-1200X-S (1” O.D tube furnace) RM 190
EQ-QB-1042 100 x 42 x 20 mm Can fit in MTI 50 - 80 mm O.D tube furnace RM 255
EQ-QB-1062 100 x 60 x 26 mm Can fit in MTI OTF1200-80 tube furnace (3” - 80 mm O.D tube furnace) RM 320
EQ-QB-3062 300 x 60 x 28 mm Can fit in MTI OTF1200-80 tube furnace (3” - 80 mm O.D tube furnace) RM 530
EQ-QB-4284 420 x 80 x 40 mm Can fit in MTI OTF1200-100 tube furnace (1000 O.D tube furnace) RM 705
EQ-QF-0806 218 x 162 x 50 mm • Constructs a flat surface inside the processing tube where can put sample on
RM 5,820
• Can be fit in MTI VBF-1200X-H8 Bench Top Vacuum Chamber Furnace
EQ-QB-1025 Diffusion of 1” wafer • Design for diffusion, oxidation and annealing 1” Si wafer
RM 1,360
processing • Can fit in MTI OTF-1200X-S50 tube furnace (2” tube furnace)
EQ-QB-8025 Diffusion of 8” wafer • Can fit in MTI GSL1100X8 tube furnace
RM 2,950
processing • Can carry 25 piece wafers of 8” diameter in each boat
EQ-QB-2025 Diffusion of 2” wafer • Can carry 25 piece wafers of 2” diameter x 0.5 mm thickness in each boat
RM 1,520
processing • Can fit in MTI OTF1200-3 tube furnace (3” tube furnace)
EQ-QB-3025 Diffusion of 3” wafer • Can carry 25 piece wafers of 3” diameter x 0.5 mm thickness in each boat
RM 1,520
processing • Can fit in MTI OTF1200-4 tube furnace
EQ-QB-4025 Diffusion of 4” wafer • Can carry 25 piece wafers of 4” diameter x 0.5 mm thickness in each boat
RM 1,750
processing • Can fit in MTI OTF1200X6 tube furnace
EQ-QB-6025 Diffusion of 6” wafer • Can carry 25 piece wafers of 6” diameter in each boat
processing • Can fit in MTI GSL1100X8 tube furnace and Compact Vacuum Chamber RM 2,350
Furnace EQ-VBF-1200X
EQ-QB-4025S Diffusion of 4”X 4” • Can carry 25 piece wafers of 4” x 4” square x 0.5 mm thickness in each boat
wafer processing • Can fit in MTI OTF-1200X-5L, VBF-1200X-H8, and OTF-1100X-8.5 tube RM 2,950
furnace

GRAPHITE CRUCIBLE
Graphite crucible can withstand the high temperature, and has good resistance to chemical erosions and thermal shock. Especially graphite
crucible is ideal for the melting of aluminum, copper and other metals.

Graphite Crucible
Model EQ-G40 EQ-GR009G
O.D. 1.5” Top: 2.285”
Bottom: 1.81”
I.D. 1.25” 1.415”
Depth 3.75” 3.06”
Height 3.96” 3.435”
Temperature 399°C to 2760°C
Compressive EQ-G40
42.7 MPa
Strength EQ-GR009G
Price RM 172.00 RM 147.50

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 29

 MTI USA

MORTAR & PESTLE

Agate Mortar & Pestle
Model Outside diameter (mm) Inside diameter (mm) Size (inch) Price
MTA-2 50 40 2 RM 126
MTA-3 75 60 3 RM 245
MTA-4 100 80 4 RM 585
MTA-5 125 110 5 RM 780
MTA-6 150 130 6 RM 1,080
MTA-7 175 160 7 RM 1,680
MTA-8 200 190 8 RM 2,780

SLI INSTRUMENTS CHINA

OTHER INSTRUMENTS
SLI-BDO-35D SLI-OOI-10A SLI-DO-9055A
LABORATORY EQUIPMENT

Digital Laboratory Drying Oven Dual Purpose Oven/Incubator Force Air Convection Drying Oven
• Power: 1200 W • Power: 850 W • Consists of 50 liter
• Temperature up to 250°C • Temperature up to 250°C • Power: 600 W
• Dimension: 35 x 35 x 35 cm • Dimension: 25 x 26 x 25 cm • Temperature up to 300°C
• Dimension: 42 x 39.5 x 35 cm
RM 1,970 RM 3,200 RM 3,700

SLI-APG-100 SLI-SG-160 SLI-IT-852B SLI-IT-350

High Speed All Purpose Grinder Laboratory Grinder Infrared Thermometer

• Speed up to 26000 rpm • Speed up to 5000 rpm • Temperature ranges from • Temperature ranges from
• Mesh size: 40-200 • Mesh Size: 40-120 -18°C to 650°C -50°C to 350°C
• Weight: 3.5 kg • Weight: 58 kg
RM 850 RM 3,950 RM 350 RM 300

SLI-IA-814 SLI-IA-6G SLI-SR-110ATC SLI-ECM-811ATC SLI-S-212ATC

Emulsion Concentrator
Timber Moisture Meter Paper Moisture Meter Saccharometer Saltmeter
Meter
• Moisture range: 5% - 40% • Moisture range: 0% - 40% • Range: 0 - 5% • Range: 0 - 15% • Range: 0 - 28%
• Accuracy: +/- 1% • Accuracy: +/- 1% • Min value: 0.10% • Min value: 0.5%, • Min value: 0.20%
0 - 15%,0.5%
RM 120 RM 150 RM 350 RM 285 RM 285

30 KGC RESOURCES
LJUHV TAIWAN

CUSTOMIZED SYSTEM
In order t o support our customer towards sophisticate research especially in the area of Nanomaterial, Semiconductor, MEMS, PV, LED,
Surface Acoustic Wave Technology, Thin Film Coating, and Ultra High Vacuum Technology; we are currently forming business alliance with

NANOMATERIAL & SEMICONDUCTOR

LJ-UHV in providing the technology know how and equipment for the above endeavor. Aside from the precision equipment, we are supplying
a complete line of pure material, compound, and substrate in various purity for completion of our equipments.

LJ-UHV Site Work located in Taiwan

The customized systems are inclusive of: Pulse Laser Deposition Coating, Ultra High Vacuum Magnetron Sputtering, Continuous Vacuum
Magnetron Sputtering, Ion Sputtering, Electron Beam Evaporation, Thermal Evaporation with Plasma Assisted Vapor Deposition Equipment
and Induction Coupled Plasma. LJ-UHV Customized System are featured with Human-Machine Interface (HMI) controller for user convenience
in handling their system.

Chamber Pulse Laser

Sputter Cathode
Deposition System

Confocal Sputter
Single Target
PLD

Five
Confocal
Target Sputter
Manipulator Cathode
LJUHV CUSTOMIZED SYSTEM is complete with Human-Machine Interface (HMI) controller for user convenience in handling their system.

Confocal Sputter System Plasma Enhanced Chemical Vapor Pulse Laser Deposition System
Deposition System

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 31

 LJUHV TAIWAN

CUSTOMIZED SYSTEM

Sputter System PLD+Sputter System

LABORATORY EQUIPMENT

Lab Scale Thermal

Evaporation System
Crystal Puller
Confocal Sputter with Load-lock Chamber

Lab Scale PECVD

PRODUCTS CATALOG
ULTRA HIGH VACUUM SYSTEM
Providing the original equipment supply, consultation,calibration services,
and equipment integration for ultra high vacuum(1x10-8 ~1x10-9 torr)
application in thin film coating, Molecular Beam Epitaxial, Nano-wire
synthesis and etc.

32 KGC RESOURCES
LJUHV TAIWAN

IN LINE SPUTTER SYSTEM

CHARACTERISTIC
• Designed for pilot scale, experimental usage

NANOMATERIAL & SEMICONDUCTOR

• Suitable for Solar Cell, Laser, EMI
• Horizontal sputtering deposition
• Uniform gas flow conductance design
• High target utilization of magnetron cathode design
• Quick exchanging target design
• 19” TFT panel HMI
• Alarm history record
• DC & RF power safety interlock

In Line Sputter for CIGS Solar Cell

HV SPUTTERING SYSTEM
• Single layered inner chamber made of SUS304; while outer chamber is electro-
polished
• Removable top plate for confocal sputtering source
• Aluminum alloy type font access door with shutter shielding to permit uncoated viewing
window
• Rotation inlet port, substrate up/down inlet port, and thermal test port are installed at
the base plate
• High vacuum turbo pump with flow rate up to 400 l/sec equipped with air cooling
function
• Dual digital LED display with 5 set points relay (Low vacuum gauge from 760 torr - 10-3
torr while high vacuum gauge up to 10-3 torr - 10-8 torr)
• Digital display for load-lock chamber (Low vacuum gauge from 760 torr - 10-3 torr)
• Mass flow controller to control inert gas and working gas
• Process pressure controller to hold function for plasma ignition
• Water cooling magnetron sputter cathode
• Plasma generator RF 300 W & auto match network
• Plasma generator DC 1000 W
• PLC control with 7” LCD touch screen

VACUUM REFLOW OVEN

• Rectangular SS304 chamber with double layer, water cooling
fabricated
• Consists of main exhaust port, rough pumping port, and vacuum
gauge port
• Rotary mechanical pump up to 500 lpm
• Consists of front end pneumatic control valve and pneumatic control
valve for exhaust buffering
• Digital vacuum gauge with pressure range from atmosphere
pressure to 10 x 10-3 torr
• Equipped with pneumatic control isolation valve
• Hardware to read out data into PLC programming
• PLC programmable control with 10” color touch screen HMI
• Vacuum exhaust/vent control
• Mass flow control/working procedure control
• Programmable temperature control
Substrate Stage
• Alarm display and record; authority control, and interlock for safety

PROMOTIONAL PRODUCTS CATALOG 2014 www.kgcresources.com | www.kgcscientific.com 33

 LJUHV TAIWAN

PECVD SYSTEM
This system is specifically designed for thin film deposition solutions of
SiC, SiNx, SiOx, and SiOxNy materials used in the manufacturing of IC’s,
MMICs, LEDs, LDs, VCSELs, and waveguides and MEMS devices of Si and
GaAs substrates. It utilizes a capacitively RF coupling plasma technology
to independently bias the upper electrode and/or substrate for controlling
the plasma density and ion energy. Reproducible thermal uniformity using
a calotto heater with thermocouple calibration with optimized uniform gas
laminar flow stream provided by specially designed shower head and pumping
channels. This system is customized to optimize deposition rate, refractive
index, film stress control, yield, throughput, and device performance.

PLC System View ports at the side wall

E-BEAM EVAPORATOR SYSTEM

This system is specifically designed for metal/non-metal film deposition process of R&D laboratory and pilot
plant production applications. Key performance features are including evaporation of uniform metal, dielectric,
LABORATORY EQUIPMENT

and insulator films on a variety of substrate materials (metal, semiconductor, insulator). Additional features are
including versatility, ease of operation, and long term reliability for evaporation of single and multi-layer thin/
thick films.
• D type chamber with single layer made of SUS304, electropolished
• Front opening/closing door with automatic electro-magnetic lock/unlock
• Door seal is designed as elastomeric seal
• High voltage fittings, sweep signal, crucible index drive, E-Gun body cooling
and shutter drive feedthrough are provided at the base plate
• High vacuum turbo pump with the pumping speed up to 600 lps and ultimate
pressure up to 5x10-10 mbar is equipped
• Gas inlet feedthrough, rotation drive, and quartz sensor feedthrough are
provided at the top plate
• Telemark deposition controller for layer thickness, rate, and process
monitoring
Substrate Stage
• PLC based operation control with color touch screen HMI interface
• Backside quartz radiant heater arrays with reflector, deposition shield (max
320°C)

ICP-RIE SYSTEM
This system is specifically designed for dry etching solutions of a wide variety of metals, dielectrics,
and semiconductor materials. It utilizes an Inductively Coupled Plasma (ICP) source to generate a high-
density plasma with a separate RF power supply to independently bias the substrate for controlling
the ion energy. Reproducible and uniform thermal control is achieved with active cooling/heating
using mechanical clamping, (helium) backside cooling, and a recirculating fluid electrode. The robust,
reliable, production-proven ICP-100 is customized to optimize smooth sidewall profile control, yield,
throughput, and device performance.
• Single layer SUS304, electropolished chamber with manual open/close door with a view port
• Linear automatic magnetic (with manual override) vacuum transfer system for the transfer of the
carrier between the load-lock chamber and main vacuum chamber
• Up/down wafer lifter for accepting/releasing wafer from/onto carrier finger into process chamber
• Roughing pump up to 300 lpm with vacuum level less than 5 x 10-4 torr
• Pneumatic control for roughing valve, purge/vent valve, foreline valve
• Vacuum gauge controller attached with Pirani gauge heads ranges from atmosphere pressure to
5 x 10-4 torr
• PLC/PC based industrial computer to control complete system
Substrate Stage
• Graphic multi-tasking real time control/display software operation for all sensors and drivers

34 KGC RESOURCES
MTI USA

Li-ion Coin Cell Fabrication & Equipment

LI-ION BATTERY FABRICATION

Step 1: Electrode Sheet Preparation
Furnace to sinter raw active material Milling Machine to grind and
(Cathode & Anode) normalize the sintered material
e.g: OTF-1200X-S e.g: MSK-SFM-1

Coater to coat paste on current collector Mixer to mix active, conductive, and
and attached Heater used to dry it. binder material into paste in vacuum
e.g: MSK-AFA-III e.g: MSK-SFM-7

Rolling Press (Calendar) to roll the Vacuum Oven to bake the electrode
electrode to desired thickness to drive away moisture inside
e.g: MSK-HRP-01 e.g: EQ-DZF-6050

Step 2: Cell Assembly

Disc Cutter to cut single coated anode, Soak them into electrolyte in Glove
cathode, and separator into disc shape Box with H2O and O2 lower than 1 ppm
e.g: MSK-T-10 e.g: EQ-VGB-6

Stack the discs by the order in the coin cell case: Cathode + Separator + Anode+ Spacer + Spring
(Current collector from both electrodes contact to the concave side of the each case part)

Electrode Filler to fill proper amount Crimping Machine to crimp the coin cell so
of electrolyte into the case that the battery core is sealed in the case
e.g: BD-10ML e.g: MSK-110

Step 3: Battery Testing

Battery Analyzer to test the coin cell’s performance and Impedance Tester to measure battery’s internal resistance
e.g: BST8-3

www.kgcresources.com | www.kgcscientific.com 35
 MTI USA

Li-ion Cylindrical Battery Fabrication & Equipment

Step 1: Electrode Sheet Preparation

Furnace to sinter raw active material Milling Machine to grind and
(Cathode & Anode) normalize the sintered material
e.g: OTF-1200X-S e.g: MSK-SFM-1

Coater to coat paste on current collector Mixer to mix active, conductive, and
and attached Heater used to dry it. binder material into paste in vacuum
e.g: MSK-AFA-III e.g: MSK-SFM-7

Rolling Press (Calendar) to roll the

electrode to desired thickness
e.g: MSK-HRP-01

Step 2: Cell Assembly (Winding Method)

LI-ION BATTERY FABRICATION

Slitting Machine to cut electrode Ultrasonic Welding Machine to join multi-

sheet to strips of desired size layers of electrode and tabs to collectors
e.g: MSK-CSE-300 e.g: MSK-800

Vacuum Oven to remove Short-Circuit Winding Machine to form layers of Anode,

any moisture within the cell Detector to test the Separator, and Cathode into a cell core
e.g: EQ-DZF-6050 integrity of the cell e.g: MSK-112A

Step 3: Case Sealing

Spot Welding Machine to connect cell Grooving Machine to create indent on
to the bottom of the case (grounding) the neck of the case for proper sealing
e.g: MSK-330A e.g: MSK-500-18650

Electrolyte Filling to inject the case Spot Welding Machine to attach the cell
with electrolyte within Glove Box to cap (positive)
e.g: BD-10ML e.g: MSK-SFM-7

Crimping Machine to align the cap with Battery Analyzer to charge/discharge the
open end of the and seal it inside Glove Box assembled battery for cell activation
e.g: MSK-510-18650 e.g: BST8-3

Step 4: Battery Testing

Battery Analyzer to test the battery’s performance and Impedance Tester to measure battery’s internal resistance
e.g: BST8-3

Note: ‘Cell’ is the battery core composed of electrodes and separator

36 KGC RESOURCES
MTI USA

Li-ion Pouch Battery Fabrication & Equipment

Step 1: Electrode Sheet Preparation

Furnace to sinter raw active material Milling Machine to grind and
(Cathode & Anode) normalize the sintered material

LI-ION BATTERY FABRICATION

e.g: OTF-1200X-S e.g: MSK-SFM-1

Rolling Press (Calendar) to Coater to coat paste on Mixer to mix active,

roll the electrode to desired current collector and attached conductive, and binder
thickness Heater used to dry it. material into paste in vacuum
e.g: MSK-HRP-01 e.g: MSK-AFA-III e.g: MSK-SFM-7

Step 2: Cell Assembly

Stacking Method
Electrode Mold Cutting Machine Stacking Machine to stack layers in form of
to cut out electrolyte with lead Anode + Separator + Cathode + Separator+...
e.g: MSK-180 e.g: MSK-111A

Winding Method
Slitting Machine to cut electrode Winding Machine to wind strips of Anode +
sheet to strips of desired size Separator + Cathode + Separator+...
e.g: MSK-CSE-300 e.g: MSK-112A

Vacuum Oven to remove any Short-Circuit Detector Ultrasonic Welding Machine to

moisture within the cell to test the integrity of the weld current collector and tab together
e.g: EQ-DZF-6050 cell e.g: MSK-800

Step 3: Case Formation & Sealing

Cup Forming Machine to punch Top & Side Heat Sealing Machine to
pouch shape to place the cell seal top and shorter side after double-up
e.g: MSK-120 e.g: MSK-140

Vacuum Primary-Sealing Machine to Electrolyte Filling to inject the case

seal longer side under vacuum with electrolyte within Glove Box
e.g: MSK-115A e.g: BD-10ML

Battery Analyzer to charge/discharge the

assembled battery for cell activation
e.g: BST8-3

Step 4: Battery Testing

Battery Analyzer to test the battery’s performance and Impedance Tester to measure battery’s internal resistance
e.g: BST8-3

Note: ‘Cell’ is the battery core without case and electrolyte

www.kgcresources.com | www.kgcscientific.com 37