t SACARDANDE ENGINEERS Calibration Services, Third Party Inspection, Dimensional Inspection, Product Validation. CALIBRATION CERTIFICATE CERTNO. C-0978 [CERTIFICATE NO. ‘SE/2489/177952, DATE, 103017 PAGE ‘TOF T [CUSTOMER NAME AND ADDRESS LETTER /CHALLAN NO LOCATION OF CALIBRATION TEM MAKE, RANG SE INWARD NUMBER CUSTOMER ID |CALIBRATION STANDARD ITRACEABILITY OF STANDARD ENVIRONMENTAL CONDITION REF DOCUMENT M/s. Kalzip India Pvt. Ltd. Cio Tata Stee! Intl, India Ltd. , One Forbes Bldg. , 3rd Floor, Near Kalaghoda, Dr. V. B. Gandhi Marg, Fort, Mumbai - 400 001 Letter RECEIPT DATE 06/03/2017 Inhouse Digimatic Micrometer Mitutoyo MODEL, 293 - 821 0-25 mm LEASTCOUNT 0,001 mm SE/2489/1 MFG NO 15268914 1)M 10 Pieces Slip Gauge Blocks Tungsten Carbide Mikronix Gr "0" (SE/015) 1) Mikronix Cal Centre Cert No SG/15/0007 Did 05/04/16 Valid upto 05/04/2018 ‘Temperature 202°C Relative Humidity 40-60% IS 2967-1983 (Reaffirmed 2008)/ Mitutoyo Spec Cat No.GB-18001 (1) Page No.40 2) This report may not be reproduced, except in full, without prior per ‘Any correction inthe certificate, invalidates the certificate, 3) The Standard used for Calibration are Traceable to National Standards PROCEDURE NUMBER w-006 UNCERTAINTY OF MEASUREMENT 41.00 nm (At 95% Confidence Level ) DATE OF CALIBRATION 10/03/2017 NEXT RECOMMENDED DATE _10/03/2018 ‘OBSERVATIONS: Parameter Specified Value in pm ‘Observerd Value in pam 0" Setting = 2 Adjusted to 0 fFlatness_: 1) Anvil 10 03 2) Spindle 1.0 03 (Parallelism of Anvil 2.0 06, ERROR IN TRAVERSE Specified Value in ym ‘Slip Size in mm ‘Obs Reading in mm Err 2.50 2.499 3.10) 5.099 7.107 7.700 10.30 10.300 12.90 12.899 320 13.00 14.999 17.60 17.599 20.20 20.199 22.80 22.799 25.00 24.998 D BY AUTHORISE! RANE, SSNEMLEKAR [YAIEAWANT ‘ALIBRATOR Q&T. MANAGER _/CALIBRATION ENGINEER, NOTE 1) This eport refers only’ tothe particular item (s) submitted for calibration and are vali at the time of and under the condition of measurement of Sacardande Engineers= SACARDANDE ENGINEERS 3 Calibration Services, Third Party Inspection, Dimensional Inspection, Product Validation. CALIBRATION CERTIFICATE aR [CERTIFICATE NO. ‘SE/2489/277953 DATE, 1032017 PAGE 1 0F1 ICUSTOMER NAME Mis. Kalzip India Pvt. Ltd. Cio Tata Steel Intl, India Lt Near Kalaghoda, Dr. V. B. + One Forbes Bldg. ,3rd Floor, sandhi Marg, Fort, Mumbai - 400 001 LETTER / CHALLAN NO Letter RECEIPT DATE 06/03/2017 LOCATION OF CALIBRATION Inhouse TEM Digimatic Micrometer MAKE Mitutoyo MODEL 293 - 821 IRANGE, 0-25 mm LEAST COUNT 0.001 mm |SE INWARD NUMBER SE24892 MFG NO 15268852 |CUSTOMER ID - . CALIBRATION STANDARD 1) M 10 Pieces Slip Gauge Blocks Tungsten Carbide Mikronix Gr "0" (SE/O15) [TRACEABILITY OF STANDARD —_1) Mikronix Cal Centre Cert No SG/15/0007 Did 05/04/16 Valid upto 05/04/2018 ENVIRONMENTAL CONDITION Temperature 20:%2%C Relative Humidity 40 - 60% REF DOCUMENT IS 2967-1983 (Reaffirmed 2008)/ Mitutoyo Spee Cat No.GB-18001 (1) Page No.40 PROCEDURE NUMBER w-006 JUNCERTAINTY OF MEASUREMENT +£1.00 jim (At 95% Confidence Level ) DATE OF CALIBRATION 10/03/2017 NEXT RECOMMENDED DATE _ 10/03/2018 ‘OBSERVATIONS Parameter ‘Specified Value in um Observerd Value in jm 0" Setting = 0.0 Flatness : 1) Anvil TO 03 2) Spindle 10 03 [Paralietism of Anvil 2.0 06 ERROR IN TRAVERSE ‘Specified Value in jim ‘Slip Size in mm ‘Obs Reading in mm Error in em 2.50 2.500 0 5.10 5.101 1 7.10) 7701 i 10.30 10.307 1 aa 12.90 12.900 0 15.00 15.000 0 17.60 17.601 i 20.20 20.201 1 2.80 22.800 0 25.00 24,999 =I DBY AUTHORISE! a [RANE S.SNEMLEKAR / PAM SAWANT CALIBRATOR Q&T. MANAGER ‘CALIBRATION ENGINEER NOTE 1) This report refers only to the particular item (s) submited for calibration and are valid at the time of and under the condition of measurement 2) This report may not be reproduced, except in full, without prior permission of Sacardande Engineers Any correction in the certiticate, invalidate the certificate, 3) The Standard used for Calibration are Traceable to National Standardst SACARDANDE ENGINEERS Calibration Services, Third Party Inspection, Dimensional inspection, Product Validation, 2” ° CALIBRATION CERTIFICATE oc [CERTIFICATE NO. SE2A8913/7954 DATE TON320 PAGE _10FT [CUSTOMER NAME, Mis. Kalzip India Pvt. Ltd. JAND ADDRESS Cio Tata Steet Intl, India Ltd. , One Forbes Bldg. , 3rd Floor, Near Kalaghoda, Dr. V. B. Gandhi Marg, Fort, Mumbai - 400 001 LETTER / CHALLAN NO. Letter RECEIPT DATE 06/03/2017 LOCATION OF CALIBRATION Inhouse rreM Digimatic Micrometer MAKE Mitutoyo MODEL 293 - 821 RANG 0-25 mm LEASTCOUNT 0.001 mm. ISE INWARD NUMBER SE2489/3 MFG NO 15268874 |CUSTOMER ID = CALIBRATION STANDARD 1) M10 Pieces Slip Gauge Blocks Tungsten Carbide Mikronix Gr "0" (SE/015) [TRACEABILITY OF STANDARD —_1) Mikronix Cal Centre Cert No SG/15/0007 Dtd 05/04/16 Valid upto 05/04/2018 ENVIRONMENTAL CONDITION Temperature 202°C Relative Humidity 40-60% REF DOCUMENT 1S 2967-1983 (Reaffirmed 2008)/ Mitutoyo Spee Cat No.GB-18001 (1) Page No.40 PROCEDURE NUMBER w-006 JUNCERTAINTY OF MEASUREMENT 1.00 ym (At 95% Confidence Level ) DATE OF CALIBRATION 10/03/2017 NEXT RECOMMENDED DATE _ 10/03/2018 ‘OBSERVATIONS Parameter Specified Value in pm ‘Observerd Valve in jm PO" Setting = ~5 Adjusted to 0 latness 1) Anvil 10) 03 2) Spindle 10 03 Parallelism of Anvil 2.0 06 ERROR IN TRAVERSE Specified Value in pm Slip Size in mm Obs Reading in mim Error in im 2.50 2.500 0 5.10 5.101 1 7.10 7.100 0 10.30 10.300 0 oy 12.90 12,900 0 15.00 15.000 0 17.60 17.600 0 20.20 20.200 0 22.80 2.800 0 25.00 24.999 =I BY AUTHORISED BY « /-M. RANE S.SNEMLEKAR JPEMSA\ CALIBRATOR Q&T. MANAGER / CALIBRATION ENGINEER NOTE 1) This report refers only to the particular item (s) submited for calibration and are valid atthe time of and under the condition of measurement 2) This report may not be reproduced, except in full, without prior pes of Sacardande Engineers ‘Any correction in the certificate, invalidates the certificate. 3) The Standard used for Calibration are Traceable to National Standardste SACARDANDE ENGINEERS : Calibration Services, Third Party Inspection, Dimensional Inspection, Product Validation, CALIBRATION CERTIFICATE cen [CERTIFICATE NO. SE2489/477991 DATE, Tos2017 PAGE _10FT [CUSTOMER NAME Mis. Kalzip India Pvt. Ltd. AND ADDRESS Cio Tata Stecl Intl. India Ltd. , One Forbes Bldg. , 3rd Floor, Near Kalaghoda, Dr. V. B. Gandhi Marg, Fort, Mumbai - 400 001 LETTER /CHALLAN NO Letter RECEIPT DATE 06/03/2017 LOCATION OF CALIBRATION Inhouse TEM Digimatic Caliper MAKE, Mitutoyo MODEL 500 - 196 - 20 RANGE 0-150: mm LEASTCOUNT 0.01 mm |SE INWARD NUMBER SE/2489/4 MFG NO 11638598 CUSTOMER ID ~ CALIBRATION STANDARD 1) M 88/1 Pieces Slip Gauge Blocks Tungsten Carbide ronix Gr "0" (SE/045) TRACEABILITY OF STANDARD —_1) Mikronix Cal Centre Cert No SG/15/0009 Did 05/04/2016 Valid upto 05/04/2018 ENVIRONMENTAL CONDITION Temperature 202°C Relative Humidity 40-60% REF DOCUMENT 1S 3651 (Part-2)-1985(Reaffi. 2010)/Mitutoyo Spec Cat No.£-2009, Page No, D-7 UNCERTAINTY OF MEASUREMENT 49.40 ym (At 95% Confidence Level ) PROCEDURE NO. W-001 DATE OF CALIBRATION 10/03/2017 NEXT RECOMMENDED DATE __ 10/03/2018 ‘OBSERVATIONS Parameter ‘Specified Value in jum ‘Observerd Value in jim Parallelism of Measuring Faces i) Ext Face 10 5 i) Int Face 10 5 Zero Error i) Ext Measurement z10 0 ii) Depth Measurement 10 o Specified valueingm| SUPSie ‘Obs Avg External Error in | Slip Size | _ Obs Avg Internal | Error in mm Reading on UC in mm| wm | inmm_| Reading on UUC inmm| xm 15.00 15.00 ‘0 [10.00 10.00 0 4121 421 0 | 30.01 30.01 0 +20 72.50 72.50 ‘0 | 70.00 9.9 =10) 100.79 100.78 =10 | 100.007 99.99 =10 130.00 130.00. (0 [129.9 129.98 =10 Specified value in ym Slip Size in mm ‘Observed Avg Depth Reading on UC in mm | Error in am! 10.00 9.99 =10 30.00 29.99 =10 +20 70.00 69.99 =10 110.00, 109.98 220 D BY AUTHO} © VM. RANE S.S.NEMLEKAR /P! CALIBRATOR Q.& T, MANAGER / CALIBRATION ENGINEER, NOTE 1) This report refers only to the particular item (s) submitted for ealibration and are valid atthe time of and under the condition of measurement 2) This report may not be reproduced, except in full, without prior permission of Sacardande Engincersby SACARDANDE ENGINEERS s Calibration Services, Third Party Inspection, Dimensional inspection, Product Validation. CALIBRATION CERTIFICATE CERT.NO. C-0978 [CERTIFICATE NO. SEAAS9ISITON DATE 1070372017 PAGE 1 OFT CUSTOMER NAME Mis. Kalzip India Pvt. Ltd. |AND ADDRESS. C/o Tata Steel Int. India Ltd. , One Forbes Bldg. , 3rd Floor, Near Kalaghoda, Dr. V. B. Gandhi Marg, Fort, Mumbai - 400 001 LETTER /CHALLAN NO Letter RECEIPT DATE 06/03/2017 LOCATION OF CALIBRATION Inhouse ITEM Digimatic Caliper MAKE, Mitutoyo MODEL, 500 - 196 -20 RANGE, 0- 150mm LEAST COUNT 0.01 mm [SE INWARD NUMBER SE/2489/5 MFG NO 11639040 CUSTOMER ID s CALIBRATION STANDARD 1) M 88/1 Pieces Slip Gauge Blocks Tungsten Carbide Mikronix Gr "0" (SE/045) TRACEABILITY OF STANDARD —_1) Mikronix Cal Centre Cert No SG/15/0009 Dtd 05/04/2016 Valid upto 05/04/2018 ENVIRONMENTAL CONDITION Temperature 202°C Relative Humidity 40 - 60% REF DOCUMENT IS 3651(Part-2)-1985(Reaffi.2010/Mitutoyo Spec Cat No.E-2009, Page No. D-7 UNCERTAINTY OF MEASUREMENT 9.40 ym (At 95% Confidence Level ) PROCEDURE NO. W-001 DATE OF CALIBRATION 10/03/2017 NEXT RECOMMENDED DATE 10/03/2018 “OBSERVATIONS Parameter Specified Value in ym Observerd Value in jm [Parallelism of Measuring Faces i) Ext Face 10 3 ii) Int Face, 10. 6 [Zero Error i) Ext Measurement 210 0 ii) Depth Measurement 10 0 Specified vatuein pm] SuPSizein [Obs Avg External [Error in] Slip Size | — Obs Avg Internal] Error in es be mm Reading on UUC in mm| jum | _inmm_| Reading on UUC in mm| pm 15.00 14.99 =10_ | 10.00 9.99 =10) 41.21 4121 0 _| 3001 30.01 0 #20 72.50, 72.50 0 [70.007 69.98 =20 100.79 100.78 =10 | 100.00 99.98 =20 130.00 129.99. =10 [129.9 129.98 =10 Specified value in pm. Slip Size in mm ‘Observed Avg Depth Reading on UUC in mm | Error in jm] 10.00 9.99 =10 30.00) 30.00 0 +20 70.00 69.99 =10) 110.00 109.99 10) DBY AUTHO! WY SW RANE S.S.NEMLEKAR /| ac CALIBRATOR Q.& T. MANAGER / CALIBRATION ENGINEER NOTE 1) This report refer only to the particular item (s) submited for calibration and are valid atthe time of and under the condition of measurement 2) This report may not be reproduced, except in full, without prior permission of Sacardande Engineers “90h MeBeedd Eataie: |B © Memes Mimem AAA Mcumied ANSLIEEE “Col ~ SERA FRAT “SROMEAD Toler OEE Ene.) SACARDANDE ENGINEERS ——__-_ Calibration Services, Third Party Inspection, Dimensional Inspection, Product Validation. CALIBRATION CERTIFICATE Cone. Ge CERTIFICATE NO. SE/2489/677993, DATE, To/Os2017 PAGE 1 OFi [CUSTOMER NAME M/s. Kalzip India Pvt, Ltd. |AND ADDRI Cio Tata Steel Intl. India Ltd. , One Forbes Bldg. , 3rd Floor, Near Kalaghoda, Dr. V. B. Gandhi Marg, Fort, Mumbai - 400 001 LETTER /CHALLAN NO Letter RECEIPT DATE 06/03/2017 LOCATION OF CALIBRATION Inhouse TEM Digimatic Caliper MAKE, Mitutoyo MODEL 500 - 196 - 20 RANGE 0- 150mm LEASTCOUNT 0.01 mm |SE INWARD NUMBER SE/2489/6 MFG NO 11638613 |CUSTOMER ID = ICALIBRATION STANDARD 1) M88/I Pieces Slip Gauge Blocks Tungsten Carbide ronix Gr "0" (SE/045) |TRACEABILITY OF STANDARD —_1) Mikronix Cal Centre Cert No SG/15/0009 Did 05/04/2016 Valid upto 05/04/2018, ENVIRONMENTAL CONDITION Temperature 202°C Relative Humidity 40-60% REF DOCUMENT 1S 3651(Part-2)-1985(Reaffi. 2010/Mitutoyo Spec Cat No.E-2009, Page No. D-7 UNCERTAINTY OF MEASUREMENT +£9.40 um (At 95% Confidence Level ) PROCEDURE NO. W-001 DATE OF CALIBRATION 10/05/2017 NEXT RECOMMENDED DATE 10/03/2018 ‘OBSERVATIONS Parameter Specified Value in ym ‘Observerd Value in jm Parallelism of Measuring Faces i) Ext Face 10 5 ii) Int Face 10 6 [Zero Error Ext Measurement 210 0 ii) Depth Measurement 10 0 ‘Specified vaiue nym] SHPSize in [Obs Avg External [Error in [Slip Size | Obs Avg Internal | Error in mm Reading on UUC in mm| ym _|_inmm_| Reading on UUC in mm| ym 15.00 14.99 =10| 10.00 10.00 0 4121 41.20 =10 [3001 30.01 0 #20 72.50 72.49 =10 [70.00 69.99) =10 100.79 100.78 =10 | 100.00. 99.99 =10 130.00 130.00 0 | 129.99 129.99 0 ‘Specified value in yam Slip Size in mm ‘Observed Avg Depth Reading on UUC in mm | Error in pm 10.00 9.99 =10 eo 30.00 29.99 =10) “ 70.00 69.99 =10) 110.00 109.99 =10) ED BY AUTHO! Py y ANE ssnemtexa /PyAdwiea CALIBRATOR Q.& T. MANAGER /'CALIBRATION ENGINEER NOTE 1) This report refers only to the particular item (s) submited for calibration and are valid at the ti 2) This report may not be reproduced, except in full, without prior permission of Sacardande En, ‘of and under the condition of measurement vers ‘9am Metnest Fentate: | Eh Mans Randi TAA. Mamhel 00\KTR Tol «SERA FRA SARE TAD Teles: SEMEN