Configuring 3G Wireless for Modular and Fixed

Cisco Integrated Services Routers

(HWIC-3G-CDMA, HWIC-3G-CDMA-x, and
PCEX-3G-CDMA-x)

First Published: March 14, 2007

Revised: March 25, 2010

The Cisco 880G series integrated services routers (Cisco ISRs) provide Internet, VPN, voice, data, and
backup capability to corporate teleworkers and remote and small offices of fewer than 20 users. These
fixed routers are capable of bridging and multiprotocol routing between LAN and WAN ports, and
provide advanced features such as antivirus protection.
The Third Generation (3G) Wireless High-Speed WAN Interface Card (HWIC) is a multiband,
multiservice WAN card for use over CDMA Radio Access Networks (RAN). It is used as the primary
WAN connectivity and as a backup for critical applications. The 3G HWIC can also be used as the
primary WAN connection.
Both the fixed and the modular 3G routers can be used as the primary WAN connectivity and as a backup
for critical applications, and can also be used as the primary WAN connection.
It is supported on the following modular Cisco ISRs:
• Cisco 1841
• Cisco 1861
• Cisco 2800 series
• Cisco 3800 series
• Cisco 1900
• Cisco 2900
• Cisco 3900
• Cisco 880

Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
© 2010 Cisco Systems, Inc. All rights reserved.
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,

The 3G wireless Modular and Fixed Cisco ISR provides the following functionality:
• Broadband WAN connectivity using high speed cellular data technology
• Support for the following technologies:
– CDMA2000 Evolution-Data Optimized (EVDO) Revision (Rev) A
– CDMA2000 EVDO Rev 0
– CDMA Single channel Radio Transmission Technology (1xRTT)
• Automatic best-network selection
• Always-on capability
• Multiple antenna and cable options:
– Diversity antenna
– Indoor and outdoor external antennas
– Radio Frequency Ultra-Low Loss (RF-ULL) cable length from 10 ft to 75 ft
• IOS-based Mobile IP including network mobility(NEMO)
• Supports over-the-air service provisioning (OTASP), Internet over-the-air (IOTA) data profile
provisioning, and Open Mobile Alliance device management (OMA-DM).
• Multiple product SKUs for multiple CDMA carriers
• Multiple external antenna options
• Support for diversity antenna
• Static and dynamic IP addressing
• Modem-based support for mobile IP
• Cellular interface based on the async interface in Cisco IOS
• Mobile IP profile management for CDMA
• Network Address Translation (NAT) and Port Address Translation (PAT) support
• Security features such as firewall, intrusion-detection systems (IDS), and intrusion-prevention
systems (IPS)
• Support for enhanced security features, such as GET VPN, EZ VPN, DMVPN, Multi-point GRE
(mGRE), and IPSec VPN
• Auto-detecting optimized WAN switchover
• Support for Hot Standby Router Protocol (HSRP) and Virtual Router Redundancy Protocol (VRRP)
• Cellular WAN management information base (MIB)
• Diagnostic and monitoring capability
• Complete Cisco IOS feature capability
The Cisco 3G wireless Modular and Fixed Cisco ISR provides the following software functionality:
• Modem activation—You can activate the modem either by using Cisco IOS commands either
manually or by using over-the-air service provisioning (OTASP), Internet over-the-air (IOTA) data
profile provisioning or the device management protocol specified by OMA-DM.
• Modem management—You can access modem software and hardware information, radio and
network status, and data profile information by using Cisco IOS commands and SNMP MIBs.
• Dial on Demand Routing (DDR)—This allows you to set up a data call when there is data traffic to
be sent over the wireless network.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
2
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,

• Fallback connection (DDR backup)—The 3G Modular and Fixed Cisco ISR allows you to configure
the cellular modem to initiate a dialup connection when connection to a primary service is lost.
• Teardown after fallback (part of fallback DDR)—After a primary connection has failed and the
cellular connection is in fallback mode, the 3G Modular and Fixed Cisco ISR tears down the
fallback-mode connection when the primary connection is available.
• Automatic teardown—After a configurable timeout, the 3G Modular and Fixed Cisco ISR
automatically tears down a connection if there has been no activity.
• Autodetect—The 3G Modular and Fixed Cisco ISR automatically detects and uses the best available
service.
• Firmware upgrade—You can upgrade the firmware on the modem by using Cisco IOS commands.
• 3G HWIC support on Cisco Integrated Services Router (ISR) platforms, namely Cisco 1841,
Cisco 1861, Cisco 2801, Cisco 2811, Cisco 2821, Cisco 2851, Cisco 3825, and Cisco 3845.
• Comprehensive Cisco IOS MIB support including Interface (IF) MIBs and Entity MIBs.
• 3G cellular MIB support.

Table 1 shows the SKU and the frequencies supported by the 3G wireless WAN HWICs.

Table 1 SKU Description and Supported Frequencies

SKU Number Description Region Frequency Bands

HWIC-3G-CDMA-x EVDO Rev A/Rev 0/1xRTT, where x US 800/1900MHz
is an initial for a specific carrier
HWIC-3G-CDMA Generic SKU for worldwide CDMA Worldwide 800/1900MHz
network
PCEX-3G-CDMA-x Cisco 880G Series 3G Wireless North America 800/1900 MHz
Integrated Services Router, where x is
an initial for a specific carrier.

Figure 1 shows the front panel of the HWIC-3G-CDMA-x.

Figure 1 Front Panel of HWIC-3G-CDMA-x

1 Mounting Screws 4 LEDs

2 Diagnostic Port 5 Diversity Antenna Connector
3 Main Antenna Connector

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
3
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,

Note The diagnostic port is not required for normal operation. It is used only for advanced radio diagnostics.
Please refer to “Modem Troubleshooting Using the Diagnostic Port” section on page 104 for details on
enabling this port and the diagnostic tools that are supported.

Table 2 explains each of the LEDs with their functionality and the different states. The LEDs provide a
visual indication of your available services. Please refer to Chapter 13 in the Cisco Interface Cards
Hardware Installation Guide for details on hardware installation.

Table 2 3G Wireless HWIC (CDMA) LED Descriptions

LED Description
RSSI Off: Low RSSI (under -100 dBm).
Slow Green Blink: Low or medium RSSI (-99 to -90 dBm).
Fast Green Blink: Medium RSSI (-89 to -70 dBm).
Solid Green: High RSSI (-69 dBm or higher).
Solid Yellow: No service.
WWAN Off: HWIC in reset mode or not powered.
Slow blink: Searching for service.
Solid Green: Active service; no traffic detected.
Fast Blink: Active service, and traffic detected proportional to blink rate.
1xRTT 1xRTT is the active service.
EVDO 1xEVDO is the active service.
Note Both 1xRTT and EVDO Off: No service is active.

Note If the RSSI LED is solid yellow, it means that there is no service.

Note Active service means the currently available service. Your 3G WAN wireless HWIC
automatically selects the best available connection.

Feature History
Release Modification
12.4(11)XV This feature was introduced. (This image is not supported any longer.)
12.4(15)T This feature was integrated into Cisco IOS Release 12.4(15)T.
12.4(22)YB1 This feature was revised.
15.1(1)T This feature was integrated into Cisco IOS Release 15.1(1)T

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
4
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,

PCEX-3G-CDMA-x
Figure 2 shows the front panel of the PCEX-3G-CDMA.

Figure 2 Front Panel of PCEX-3G--CDMA

1 LEDs 3 USB port

1
2 3G express card slot—Supports third-party
3G card (Cisco 88xG models only)
1. See the Cisco 880 Series Integrated Services Routers data sheet for supported vendors.

Table 3 lists the LEDs and describes their functionality and different states. The LEDs provide a visual
indication of your available services. Please see the Cisco 880 Series ISR Hardware Installation Guide
for details on hardware installation.

Table 3 LED Description for PCEX-3G-HSPA-x

LED Color Description 880 Series

1 2
3G WWAN Green On—Service is established. 3G models
Slow Blinking—Searching for service.
Fast Blinking—Data is either being received or being transmitted.
3G RSSI3 Green Off—Low signal strength (lower than -100 dBm). 3G models
On—High RSSI (-69 dBm or higher).
Slow Blinking—Low or medium RSSI (-99 to -90 dBm).
Fast Blinking—Medium RSSI (-89 to -70 dBm).
Amber On—No service. 3G models

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
5
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,

LED Color Description 880 Series

3G GSM4 Green On—Service is established. 3G models
Off—No service.
5
3G CDMA Green On—Service is established. 3G models
Off—No service.
1. 3G = Third-Generation.
2. WWAN = wireless WAN.
3. RSSI = Received Signal Strength Indicator.
4. GSM = Global System for Mobile Communication.
5. CDMA = code division multiple access.

The PCEX-3G-CDMA supports the AC501 and the AC880E modem. Table 4 shows the LED
information for the LEDs located on the modem.

Table 4 Modem LED Descriptions

LED Description
Power Indicates one of the following states:
• The modem has detected or is connected to a 2G or 3G network.
• The modem is not inserted in the PC.
• The computer is off or in “suspend and resume mode”.
• The modem has been turned off using Watcher (Tools > Turn Radio
Off) or another connection client.
Solid Blue: The power is on, the modem is working normally, and the firmware
is not being updated.
Blinking Blue: The firmware is being updated. Do not remove the modem from
the PC.
Blinking Amber: The modem is searching for service (initializing).
Solid Amber: Error—either the modem is having a problem initializing
(searching for service) or is offline because of a failure. Contact your service
provider.
2G Off: The modem is unable to detect 2G service.
Blinking Amber: The modem has detected a 2G network (EDGE, GPRS, GSM)
and is ready to connect.
Solid Amber: The modem is connected to a 2G network and is able to send and
receive data.
3G Off: The modem is unable to detect 3G service.
Blinking Blue: The modem has detected a 3G network (UMTS, HSDPA) and is
ready to connect.
Solid Blue: The modem is connected to a 3G network and can send and receive
data.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
6
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Contents

Feature History
Release Modification
12.4(11)XV This feature was introduced for HWIC-3G-CDMA. (This image is not
supported any longer.)
12.4(15)T This feature was integrated into Cisco IOS Release 12.4(15)T.
12.4(15)T1 This feature was updated.
15.0(1)M The HSPA feature was introduced.
15.1(1)T The CDMA feature was integrated into the Cisco 880 Series Integrated
Service Routers with Cisco IOS Release 15.1(1)T.

Finding Support Information for Platforms and Cisco IOS Software Images
Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image
support. Access Cisco Feature Navigator at http://www.cisco.com/go/fn. You must have an account on
Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at
the login dialog box and follow the instructions that appear.

Contents
• Prerequisites for Configuring 3G Wireless, page 7
• Restrictions for Configuring 3G Wireless, page 8
• Technology Overview, page 9
• Overview of SNMP MIBs, page 10
• Configuring the 3G Wireless Modular and Fixed Cisco ISRs, page 17
• Configuring Data DedicatedTransmission Mode (DDTM), page 29
• Modem Firmware Upgrade, page 34
• Command Reference, page 35
• Troubleshooting Tips, page 102

Prerequisites for Configuring 3G Wireless

The following are prerequisites to configuring the 3G wireless HWICs:
• You must have service availability from a wireless service provider, and you must have network
coverage where your router will be physically located. For a complete list of supported carriers, see
the data sheet at the following URL: http://www.cisco.com/go/3g
• You must subscribe to a service plan with a wireless service provider. For manual activation, you
will need the following specific information from the provider:
– Master Subsidy Lock (MSL) number
– Mobile Directory number (MDN)
– MSID
The ESN number is on the modem itself, as shown in Figure 3. Make sure that your service is registered
with the ESN number. You can also obtain the ESN by using the show cellular hardware command.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
7
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Restrictions for Configuring 3G Wireless

• You must install the required antennas before you configure the 3G wireless HWIC. See the
following URLs for instructions on how to install the antennas:
– 3G-ANTM1919D—See the Cisco Multiband Swivel Mount Dipole Antenna (3G-ANTM1919D)
– 3G-ANTM1916-CM—See the Cisco Multiband Omnidirectional Ceiling Mount Antenna
(3G-ANTM1916-CM)
– 3G-AE015-R (Antenna Extension)—See the Cisco Single-Port Antenna Stand for Multiband
TNC Male-Terminated Portable Antenna (3G-AE015-R)
– 3G-ANTMOUT-OM—See the Cisco 3G Omnidirectional Outdoor Antenna
(3G-ANTM-OUT-OM)
– 3G-ANTM-OUT-LP—See the Cisco 3G Low Profile Outdoor Antenna (3G-ANTM-OUT-LP)
– 3G-ACC-OUT-LA—See the Cisco 3G Lightning Arrestor (3G-ACC-OUT-LA)
• You must make sure to check your LEDs for signal reception as described in Table 2.
• You should be familiar with Cisco IOS.

Figure 3 Location of the ESN Number

1 The ESN is located on the modem that is attached to the back of the 3G wireless HWIC. The ESN
is just below the barcode.

Restrictions for Configuring 3G Wireless

The following restrictions apply to the Cisco 3G Wireless HWICs:
• Data connection can be originated only by the 3G wireless Modular and Fixed Cisco ISRs. Remote
dial-in is not supported.
• Throughput—Because of the shared nature of wireless communications, the amount of throughput
that is experienced varies, depending on the number of active users or congestion in a network.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
8
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Technology Overview

• Cellular networks have higher latency, compared to wired networks. Latency rates depend on the
technology and carrier. Latency can increase because of network congestion.
• Any restrictions that are a part of the terms of service from your carrier.

Technology Overview
This section contains the following topics:
• CDMA Network Overview, page 9
• Overview of SNMP MIBs, page 10
• 3G Cellular WAN MIB Architecture, page 10
• Supported Cisco Antennas and Cables, page 13

CDMA Network Overview

CDMA is a standard for mobile communication. A typical CDMA network includes terminal equipment,
mobile termination, base transceiver station (BTS), base station controller (BSC), packet data serving
node (PDSN), and other data network entities. The PDSN is the interface between a BSC and a internet
gateway.
Figure 4 shows the relationship of the components of a typical CDMA network, including a PDSN and
a branch office with the 3G wireless Modular and Fixed Cisco ISRs.
As the figure shows, the branch office connects to a radio tower and a BTS. The BTS connects to a BSC,
which contains a component called the packet control function (PCF). The PCF communicates with the
Cisco PDSN for data communication and with the mobile switching center (MSC) for voice.

Figure 4 Overview of the CDMA Network

Voice
MSC PSTN

Data
Internet
Branch Office BTS/BSC PCF/
with Cellular HWIC PDSN
Leased Line
(MPLS, FR, Fiber) HQ
Carrier Network
BTS: Base Transceiver Stations
BSC: Base Station Controller
230350

MSC: Mobile Switching Center

PCF: Packet Control Function
PDSN: Packet Data Serving Node

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
9
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Technology Overview

Overview of SNMP MIBs

Simple Management Network Protocol (SNMP) development and use is centered around the
Management Information Base (MIB). An SNMP MIB is an abstract data base, i.e., a conceptual
specification for information that a management application may read and modify in a certain form. This
does not imply that the information is kept in the managed system in that same form. The SNMP agent
translates between the internal data structures and formats of the managed system and the external data
structures and formats defined for the MIB.
The SNMP MIB is conceptually a tree structure with conceptual tables. Cisco 3G MIB is discussed in
more detail in the next section. Relative to this tree structure, the term MIB is used in two senses. In one
sense it is actually a MIB branch, usually containing information for a single aspect of technology, such
as a transmission medium or a routing protocol. A MIB used in this sense is more accurately called a
MIB module, and is usually defined in a single document. In the other sense a MIB is a collection of
such branches. Such a collection might comprise, for example, all the MIB modules implemented by a
given agent, or the entire collection of MIB modules defined for SNMP.
A MIB is a tree where the leaves are individual items of data called objects. An object may be, for
example, a counter or a protocol status. MIB objects are also sometimes called variables.
MIBs for the 3G cellular Modular and Fixed Cisco ISRs can be classified into three categories:
• IF MIBs—describes interface statistics
• Cisco-Entity-Vendortype-OID-MIB.my—ENTITY-MIBs are used to provide general hardware type
for both the Modular and Fixed Cisco ISRs and the modem.
CISCO-ENTITY-VENDORTYPE-OID-MIB assigns OIDs for Cisco components (including the
HWICs & the modems). The OIDs are then used as the values of entPhysicalVendorType in the
ENTITY-MIB.
• 3G cellular MIBs—cellular or wireless-specific MIBs

3G Cellular WAN MIB Architecture

This section describes the MIB definition and implementation support for Cisco's cellular 3G WAN
products on the customer premises equipment (CPE) end.
The 3G Cellular WAN MIB supports both CDMA and GSM set of cellular standards and includes the
following technologies:
• GSM—GPRS/EDGE/UMTS/HSPA
• CDMA—1xRTT/EVDO RevA/EVDO Rev0
The 3G cellular MIB uses indexes from the cellular interface and from the modem. You can obtain the
interface index using IF-MIBs and the modem index using the ENTITY MIBs.
The 3G MIB definition includes the following major sub-trees:
• Common objects
• CDMA objects
• GSM objects
• Notifications
You can use MIB object c3gStandard defined in the c3gWanCommonTable to distinguish between
CDMA or GSM and implementing MIB for CDMA or GSM.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
10
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Technology Overview

Note Cisco 3G MIB supports both SNMP V3 and V2.

At a high level, the Cisco 3G WAN MIBs are divided into two groups and have the following structure:
1. ciscoWan3gMIBObjects—this group defines all the MIB objects for Cisco 3G WAN MIBs
2. ciscoWan3gMIBNotifs—this group defines all the notification events for Cisco 3G WAN MIBs

ciscoWan3gMIBObjects

The ciscoWan3gMIBObjects group has three sub-groups:

– c3gWanCommonTable—defines the common MIB objects for both CDMA and GSM
– c3gWanCdma—defines the MIB objects specific for CDMA 2000 standards (3GPP2)
– c3gWanGsm—defines the MIB objects specific for GSM/UMTS standards (3GPP)
c3gWanCdma
Under c3gWanCdma, there are seven sub-groups:
• c3gCdmaSessionTable for session related objects
• c3gCdmaConnectionTable for connection related objects
• c3gCdmaIdentityTable for user identity related objects
• c3gCdmaNetworkTable for network related objects
• c3gCdmaProfile for user profile related objects
• c3gCdmaRadio for radio related objects
• c3gCdmaSecurityTable for security related objects
c3gWanGsm
Under c3gWANGsm, there are five sub-groups:
• c3gGsmIdentityTable for user identity related objects.
• c3gGsmNetworkTable for network related objects.
• c3gGsmPdpProfile for PDP profile related objects.
• c3gGsmRadio for radio related objects.
• c3gGsmSecurityTable for security related objects.

ciscoWan3gMIBNotifs

Cisco Cellular 3G WAN MIB implementation supports SNMP GET (read operation) for all MIB objects,
and SNMP SET (write operation) for the following RW (read-write) objects and more:
• c3gRssiOnsetNotifThreshold
• c3gRssiAbateNotifThreshold
• c3gEcIoOnsetNotifThreshold
• c3gEcIoAbateNotifThreshold
• c3gModemTemperOnsetNotifThreshold
• c3gModemTemperAbateNotifThreshold
• c3gModemReset

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
11
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Technology Overview

• c3gModemUpNotifEnabled
• c3gModemDownNotifEnabled
• c3gServiceChangedNotifEnabled
• c3gNetworkChangedNotifEnabled
• c3gConnectionStatusChangedNotifFlag
• c3gRssiOnsetNotifFlag
• c3gRssiAbateNotifFlag
• c3gEcIoOnsetNotifFlag
• c3gEcIoAbateNotifFlag
• c3gModemTemperOnsetNotifEnabled
• c3gModemTemperAbateNotifEnabled

Note By default, all notifications are disabled. To receive notifications, you must enable these notifications.

Note The IF MIBs also have traps for the cellular interface objects that are used in conjunction with the
notification type. When you get a notification, you must check the associated objects.

Table 5 shows various notifications and what they mean.

Table 5 Traps and Notifications

Traps Details
ModemUpNotification Modem successfully recognized.
ModemDown Crash or power-cycle.
Change Notification Notifies about changes in service objects related to this
notification—previous service type to current service type.
ConnectionStatus Shows the connection status. Service type is included in this notification.

Restrictions
• For the router that runs the SNMP agent, you must configure appropriate access control (e.g.
SNMP-server community) using the Cisco IOS CLI for the NMS and agent to work properly.
• It is strongly recommended that you configure SNMP V3 with authentication/privacy when
implementing SNMP GET and SET operation.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
12
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Technology Overview

Supported Cisco Antennas and Cables

Table 6 lists the Cisco antennas that are supported for use on the 3G Modular and Fixed Cisco ISRs.
.
Table 6 Cisco Antennas Supported on Modular 3G ISRs

Maximum Gain and

Cisco Part Number Antenna Type Frequency Range Description
3G-ANTM1919D Dipole 0 dBi This is the default antenna. Multiband
omnidirectional (806–960 MHz) faceplate-mounted dipole antenna. For more
information, see the Cisco Multiband Swivel Mount
0 dBi
Dipole Antenna (3G-ANTM1919D) document.
(1710–2170 MHz)
3G-ANTM1916-CM High-gain 1.5 dBi Multiband ceiling-mounted omnidirectional antenna.
ceiling-mount (806–960 MHz) For more information, see the Cisco Multiband
omnidirectional Omnidirectional Ceiling Mount Antenna
2.5 dBi
(3G-ANTM1916-CM) document.
(1710–2170 MHz)
3G-AE015-R Extension base 0.8–6.0 GHz This antenna extension is a base with a 15-foot cable
(Antenna Extension) included for use with a dipole omnidirectional antenna.
For more information, see theCisco Single-Port
Antenna Stand for Multiband TNC Male-Terminated
Portable Antenna (3G-AE015-R) document.
3G-ANTM-OUT-OM Outdoor +2 dBi This is an outdoor low profile omindirectional mast
Omnidirectional 800/900 MHz antenna. For more information, see Cisco 3G
Omnidirectional Outdoor Antenna
+4 dBi
(3G-ANTM-OUT-OM)
1800/1900/2100 MHz
3G-ANTM-OUT-LP Low Profile Stick - 1.5 dBi This is an omindirectional stick antenna. For more
Antenna 850, 900 MHz information, see Cisco 3G Low Profile Outdoor
Antenna (3G-ANTM-OUT-LP)
- 2.5 dBi
1800, 1900, 2100 MHz
3G-ACC-OUT-LA Lightning Arrestor 800 MHz to 2200 MHz This is a quarter-wave lightning protector with
(Lightning Arrestor) integrated high-pass filter. For more information, see
Cisco 3G Lightning Arrestor (3G-ACC-OUT-LA)

Table 7 lists insertion loss information for the ultra-low-loss (ULL) LMR 400 extension cables available
from Cisco for use with 3G Modular and Fixed Cisco ISR antennas.

Table 7 Cisco Extension Cables for Use with Antennas

Cisco Product Number Cable Length Insertion Loss Frequency (MHz)

3G-CAB-ULL-20 20 ft (6 m) 1.50 dB max. 2100
3G-CAB-ULL-50 50 ft (15 m) 3.50 dB max. 2100
3G-CAB-LMR240-25 25 ft (7.5 m) 3.50 dB max. 2200
3G-CAB-LMR240-50 50 ft (15 m) 6.90 dB max. 2200
3G-CAB-LMR240-75 75 ft (23 m) 10.5 dB max. 2200

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
13
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Technology Overview

Table 8 lists loss information for the ultra-low-loss (ULL) LMR 400 cables available from Cisco for use
with 3G fixed platforms.

Table 8 Cisco Adapter Cables for using HWIC cables with 3G Fixed

Antenna Adapter
Cisco Product Number Length Insertion Loss Frequency (MHz)
3G-ACC-SSMB-TNC 14.5 inches 0.66 dB 2100
3G-ACC-TS9-TNC 13.5 inches 0.62 dB 2100

Note You can use the RG-174/U type cables to adapt the modem external antenna connection to any of the
HWIC cables and antennas.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
14
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Technology Overview

Figure 5 and Figure 6 show some antenna options for the 3G Modular and Fixed Cisco ISRs.

Figure 5 Antenna Options

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
15
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Technology Overview

Figure 6 Antenna Options

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
16
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuring the 3G Wireless Modular and Fixed Cisco ISRs

Configuring the 3G Wireless Modular and Fixed Cisco ISRs

To configure the 3G wireless Modular and Fixed Cisco ISRs, follow these procedures:
• Modem Activation and Provisioning, page 17
• Data Call Set up, page 21

Note The procedure to configure 3G on both modular and fixed Cisco ISRs is the same except for slot
numbering.
For example, for 3G HWICs, the numbering for slot 0, wic 0 and port 0 would be 0/0/0 for all commands.
For a fixed Cisco ISR, it would be only 0.
Please refer to platform-specific documentation for details on slot numbering.

Modem Activation and Provisioning

To activate and provision your modem, follow these procedures:
• Verifying Signal Strength and Service Availability, page 17
• Activating the Modem, page 19

Verifying Signal Strength and Service Availability

SUMMARY STEPS

To verify the signal strength and service availability on your modem, use the following commands
beginning in the EXEC mode.

Note For modem activation, the modem should be attached to a 1xRTT/EVDO service.

1. show cellular network

2. show cellular radio
3. show cellular hardware
4. show cellular all

DETAILED STEPS

Use the following commands to verify the signal strength and service availability on your modem
beginning in the EXEC mode:

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
17
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuring the 3G Wireless Modular and Fixed Cisco ISRs

Command or Action Purpose

Step 1 Router# show cellular <slot/wic/port> network Displays information about the carrier network, cell
site, and available service.
Example:
Router# show cellular 0/0/0 network
Step 2 Router# show cellular <slot/wic/port> radio Shows the radio signal strength.

Example:
Note The RSSI should be better than -90 dBm for
Router# show cellular 0/0/0 radio
steady and reliable connection and better
than -80 dBm for optimal data throughput.
Step 3 Router# show cellular <slot/wic/port> hardware Shows the hardware details and modem type.

Example:
Router# show cellular 0/0/0 hardware

Step 4 Router# show cellular <slot/wic/port> all Shows consolidated information about the modem,
profiles created, radio signal strength, network
security, and so forth.
Example:
Router# show cellular 0/0/0 all

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
18
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuring the 3G Wireless Modular and Fixed Cisco ISRs

Activating the Modem

The activation procedures may differ depending upon your carrier. Consult your carrier, and follow one
of the following procedures:
• Manual Activation, page 19
• Activating Using OMA-DM, page 20
• Activating Using OTASP, page 21

Note Use the show cellular controller command to obtain information for the modem type for your Modular
and Fixed Cisco ISRs.

Table 9 lists activation and provisioning process supported by different wireless carriers depepnding on
the modem MC5725 and MC5727.

Table 9 Support for Activation Procedures by SKUs and Modem Type

Sprint (-S) Verizon (-V) Generic

Activation Procedure MC5725 MC5727 MC5725 MC5727 MC5725 MC5727
Manual Activation using Yes Yes No No Yes Yes
MDN/MSID/MSL
OTASP Activation No No Yes Yes Yes Yes
OMA-DM Activation No Yes No No No No
IOTA for Data Profile refresh Yes No No No Yes Yes

Manual Activation

Note You must have valid MDN, MSL, and MSID information from your carrier before you start this
procedure.

To configure a modem profile manually, use the following command beginning in EXEC mode:

cellular slot/wic_slot/port cdma activate manual mdn msid sid nid msl

For more infomation about the parameters, see the “cellular cdma activate manual” section on page 41
In addition to activation, the modem data profile provisioning is done using a process called IOTA. IOTA
is initiated automatically when you use the cellular cdma activate manual command.

Here is a sample output from this command:

router#cellular 0/0/0 cdma activate manual 1234567890 1234567890 1234 12 12345
NAM 0 will be configured and will become Active
Modem will be activated with following Parameters
MDN :1234567890; MSID :1234567890; SID :1234; NID 12:
Checking Current Activation Status
Modem activation status: Not Activated
Begin Activation
Account activation - Step 1 of 5
Account activation - Step 2 of 5

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
19
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuring the 3G Wireless Modular and Fixed Cisco ISRs

Account activation - Step 3 of 5

Account activation - Step 4 of 5
Account activation - Step 5 of 5
Secure Commit Result: Succeed
Done Configuring - Resetting the modem
The activation of the account is Complete
Waiting for modem to be ready to start IOTA
Beginning IOTA
router#
*Feb 6 23:29:08.459: IOTA Status Message Received. Event: IOTA Start, Result: SUCCESS
*Feb 6 23:29:08.459: Please wait till IOTA END message is received
*Feb 6 23:29:08.459: It can take up to 5 minutes
*Feb 6 23:29:27.951: OTA State = SPL unlock, Result = Success
*Feb 6 23:29:32.319: OTA State = Parameters commited to NVRAM, Result = Success
*Feb 6 23:29:40.999: Over the air provisioning complete; Result:Success
*Feb 6 23:29:41.679: IOTA Status Message Received. Event: IOTA End, Result: SUCCESS

Note The IOTA start and end must have “success” as the resulting output. If you receive an error message, you
can run IOTA independently by using the cellular cdma activate iota command.

Tip A periodic refresh of the data profile may be needed as required by your carrier. Use the following
command to refresh the data profile: cellular cdma activate iota.

Activating Using OMA-DM

When you power up the modem for the first time, the modem automatically initiates Hands Free
Activation (HFA) to receive over-the-air programming for the MDN and MSID numbers and refreshes
mobile IP profile1 (MIP1). You will see the message “OMA DM Hands Free Activation session is active”
on your device.
At the end of the session, you may see one of the following three messages depending on the activation
status:
• If activation is successful: "OMA DM Hands Free Activation completed successfully"
• If activation is unsuccessful, you will see the following message (up to 5 times) indicating that
modem is retrying HFA: "OMA DM Hands Free Activation, waiting for retry in <x> seconds".
• If activation is still unsuccessful, user will see the message "OMA DM Hands Free Activation Failed
- Error: <error_code>(<error_string>). Please try again later. If the problem persists, you may need
to contact Customer Service."
To check if the account is provisioned and the modem is activated, use the show cellular profile
command. If the account is not activated, use the user-initiated mode using the Cisco IOS CLI to activate
your modem.
To activate using the Cisco IOS CLI, use the following command beginning in EXEC mode:

cellular slot/wic/port cdma activate oma-dm device-config

Router#cellular 0/0/0 cdma activate oma-dm device-config

Modem is activated
MIP profile 1 will be updated and will be active, if command is successful
Beginning OMA-DM.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
20
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuring the 3G Wireless Modular and Fixed Cisco ISRs

Router#
*Feb 5 20:50:18.207: %CELLWAN-2-OMA_DM_ACTIVE: [Cellular0/0/0]: OMA DM Device
Configuration session is active
Enzo-sustaining_1841_Live#
*Feb 5 20:50:34.755: %CELLWAN-2-OMA_DM_SUCCESS: [Cellular0/0/0]: OMA DM Device
Configuration completed successfully

Activating Using OTASP

To provision and activate your modem using OTASP, use the following command beginning in EXEC
mode:

cellular slot/wic_slot/port cdma activate otasp phone_number

Note You need to obtain the phone number for use with this command from your carrier. The standard OTASP
calling number is *22899.

router# cellular 0/1/0 cdma activate otasp *22899

Beginning OTASP activation

OTASP number is *22899
router#
*Feb 6 23:18:45.393: OTA State = SPL unlock, Result = Success
*Feb 6 23:19:10.229: OTA State = PRL downloaded, Result = Success
*Feb 6 23:19:11.169: OTA State = Profile downloaded, Result = Success
*Feb 6 23:19:11.173: OTA State = MDN downloaded, Result = Success
*Feb 6 23:19:12.537: OTA State = Parameters commited to NVRAM, Result = Success
*Feb 6 23:19:14.613: Over the air provisioning complete; Result:Success

Data Call Set up

To set up a data call, use the following procedures:
• Configuring the Cellular Interface, page 22
• Configuring DDR, page 23
• Configuring DDR Backup, page 26
• Configuring Multiple Mobile IP Profiles, page 29
• Configuring Data DedicatedTransmission Mode (DDTM), page 29

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
21
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuring the 3G Wireless Modular and Fixed Cisco ISRs

Figure 7 shows a data call setup using the 3G wireless HWIC.

Figure 7 Data Call Setup with the HWIC-3G-CDMA

Configuring the Cellular Interface

To configure the cellular interface, enter the following commands in the cellular interface mode.

SUMMARY STEPS

1. configure terminal
2. interface cellular <slot/wic/port>
3. encapsulation ppp
4. ppp chap password 0 <password>
5. asynchronous mode interactive
6. ip address negotiated

Note The modem supports both mobile IP (MIP) and simple IP (SIP). In both modes, the modem authenticates
with the network. However, when the modem is configured in MIP-preferred mode (ask your carrier
which mode is supported), if MIP authentication fails, the modem tries to set up a SIP call. The modem
uses SIP authentication parameters derived during modem provisioning and passes the CHAP
authentication challenge to the cellular interface. The purpose of the authentication challenge is to keep
the cellular interface informed of Link Control Protocol (LCP) negotiations between the modem and the
network. The authentication challenge from the modem does not have a username, so under the cellular
interface, you should configure a default CHAP password, i.e., configure only the ppp chap password
and not the ppp chap hostname. If your carrier supports only MIP, you do not need to configure either
of the two parameters.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
22
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuring the 3G Wireless Modular and Fixed Cisco ISRs

DETAILED STEPS

Command or Action Purpose

Step 1 Router# configure terminal Enters global configuration mode from the terminal.

Example:
Router# configure terminal
Step 2 Router(config)# interface cellular Specifies the cellular interface.
<slot/wic/port>

Example:
Router (config)# interface cellular 0/0/0
Step 3 Router(config-if)# encapsulation ppp Specifies PPP encapsulation for an interface configured for
dedicated asynchronous mode or dial-on-demand routing
(DDR).
Example:
Router (config-if)# encapsulation ppp
Step 4 Router (config-if)# ppp chap password <password> Defines an interface-specific CHAP password.

Example:
Note You can set the password to any value. This
Router (config-if)# ppp chap password cisco
password is used only when the modem has failed
MIP authentication and fails over to SIP mode. The
modem ignores the CHAP authentication response
from the cellular interface.
Step 5 Router(config-if)# async mode interactive Returns a line that has been placed into dedicated
asynchronous network mode to interactive mode, thereby
enabling the slip and ppp EXEC commands.
Example:
Router (config-if)# async mode interactive
Step 6 Router(config-if)# ip address negotiated Specifies that the IP address for a particular interface is
obtained via PPP/IPCP address negotiation.
Example:
Router (config-if)# ip address negotiated

Note When static IP address is required for the cellular interface, the address may be configured as ip address
negotiated. During IPCP, the network ensures that the correct static IP address is allocated to the device.
If a tunnel interface is configured with ip address unnumbered <cellular interface>, it is necessary to
configure the actual static IP address under the cellular interface, in place of ip address negotiated. For
a sample cellular interface configuration, see “Basic Cellular Interface Configuration: Example” section
on page 30.

Configuring DDR
To configure DDR for the cellular interface, follow these steps:

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
23
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuring the 3G Wireless Modular and Fixed Cisco ISRs

SUMMARY STEPS

1. configure terminal
2. interface cellular <slot/wic/port>
3. dialer in-band
4. dialer idle-timeout <seconds>
5. dialer string <string>
6. dialer group <number>
7. exit
8. dialer-list <dialer-group> protocol <protocol-name> {permit | deny | list <access-list-number> |
access-group}>
9. ip access-list<access list number>permit <ip source address>
10. line <slot/wic/port>
11. script dialer <regexp>
12. exit
13. chat-script <script name> ”” “ATDT#777” TIMEOUT <timeout value> CONNECT
14. interface cellular <slot/wic/port>
15. dialer string <string>

Command or Action Purpose

Step 1 Router# configure terminal Enters global configuration mode from the terminal.

Example:
Router# configure terminal
Step 2 Router(config)# interface cellular <slot/wic/port> Specifies the cellular interface.

Example:
Router (config)# interface cellular 0/0/0
Step 3 Router(config-if)# dialer in-band Enables DDR and configures the specified serial
interface to use in-band dialing.
Example:
Router (config-if)# dialer in-band
Step 4 Router(config-if)# dialer idle-timeout <seconds> Specifies the duration of idle time, in seconds, after
which a line will be disconnected.
Example:
Router (config-if)# dialer idle-timeout 30
Step 5 Router(config-if)# dialer string <string> Specifies the number or string to dial. Use the name
of the CHAT script here.
Example:
Router (config-if)# dialer string cdma

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
24
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuring the 3G Wireless Modular and Fixed Cisco ISRs

Command or Action Purpose

Step 6 Router(config-if)# dialer-group <number> Specifies the number of the dialer access group to
which the specific interface belongs.
Example:
Router (config-if)# dialer-group 1
Step 7 Router(config-if)# exit Enters the global configuration mode.

Example:
Router (config-if)# exit
Step 8 Router(config)# dialer-list <dialer-group> protocol Creates a dialer list for traffic of interest and permits
<protocol-name> {permit | deny | list access to an entire protocol.
<access-list-number> | access-group}>

Example:
Router (config)# dialer-list 1 protocol ip list 1
Step 9 Router(config)# ip access-list<access list Defines traffic of interest.
number>permit <ip source address>

Example:
Router (config)# ip access list 1 permit any
Step 10 Router(config)# line <slot/wic/port> Specifies the line configuration mode.

Example:
Router (config-line)# line 0/0/0
Step 11 Router(config-line)script dialer <regexp> Specifies a default modem chat script.

Example:
Router (config-line)# script-dialer cdma
Step 12 Router(config-line)exit Exits line configuration mode.

Example:
Router (config-line)# exit
Step 13 Router(config)# chat-script <script name> ”” Defines the ATDT commands when the dialer is
“ATDT#777” TIMEOUT <timeout value> CONNECT initiated.

Example:
Router (config)# chat-script cdma "" "ATDT#777"
TIMEOUT 60 "CONNECT“
Step 14 Router(config)# interface cellular <slot/wic/port> Specifies the cellular interface.

Example:
Router (config)# interface cellular 0/1/0
Step 15 Router(config-if)# dialer string <string> Specifies the dialer script (defined using the chat
script command).
Example:
Router (config)# dialer string cdma

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
25
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuring the 3G Wireless Modular and Fixed Cisco ISRs

Configuring DDR Backup

To monitor the primary connection and initiate the backup connection when needed, the router can use
one of the following methods:
• Backup Interface—The backup interface that stays in standby mode until the primary interface line
protocol is detected as down and then is brought up.
• Floating Static Route—The route through the backup interface has an administrative distance that
is greater than the administrative distance of the primary connection route and therefore would not
be in the routing table until the primary interface goes down.
• Dialer Watch—Dialer watch is a backup feature that integrates dial backup with routing capabilities.

Configuring Interfaces to Use a Backup Interface

To configure one or more interfaces to use a backup interface, use the following commands, beginning
in global configuration mode.

SUMMARY STEPS

1. interface type number

2. backup interface cellular number
3. backup delay enable-delay disable-delay

DETAILED STEPS

Command or Action Purpose

Step 1 Router(config)# interface type number Specifies the interface to be backed up and begins
interface configuration mode.
Example:
Router(config)# interface ATM0/0/0
Step 2 Router(config-if)# backup interface cellular Specifies the cellular interface as backup.
<number>

Example:
Router(config-if)# backup interface cellular0/3/0
Step 3 Router(config-if)# backup delay enable-delay Specifies delay between the physical interface going
disable-delay down and the backup interface being enabled, and
between the physical interface coming back up and
Example: the backup being disabled.
Router(config-if)# backup delay enable delay

Note You cannot configure a backup interface for the cellular interface and any other asynchronous serial
interface.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
26
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuring the 3G Wireless Modular and Fixed Cisco ISRs

Configuring DDR Backup Using Dialer Watch

To initiate dialer watch, you must configure the interface to perform DDR and backup. Use traditional
DDR configuration commands, such as dialer maps, for DDR capabilities. To enable dialer watch on the
backup interface and create a dialer list, use the following commands in interface configuration mode.

SUMMARY STEPS

1. configure terminal
2. interface type number
3. dialer watch group group-number
4. dialer watch-list group-number ip ip-address address-mask
5. dialer-list <dialer-group> protocol <protocol name> {permit | deny | list <access list number> |
access-group}
6. ip access-list <access list number> permit <ip source address>
7. interface cellular <slot/wic/port>
8. dialer-group <dialer group number>

DETAILED STEPS

Command or Action Purpose

Step 1 Router# configure terminal Enters global configuration mode from the terminal.

Example:
Router# configure terminal
Step 2 Router(config)# interface type number Specifies the interface.

Example:
Router (config)# interface ATM0/0/0
Step 3 Router(config-if)# dialer watch-group Enables dialer watch on the backup interface.
group-number

Example:
Router(config-if)# dialer watch-group 2
Step 4 Router(config)# dialer watch-list group-number ip Defines a list of all IP addresses to be watched.
ip-address address-mask

Example:
Router(config-if)# dialer watch-list 2 ip 10.4.0.254
255.255.0.0
Step 5 Router(config)# dialer-list <dialer-group> protocol Creates dialer list for traffic of interest and permits
<protocol-name> {permit | deny | list access to an entire protocol.
<access-list-number> | access-group}>

Example:
Router(config)# dialer-list 2 protocol ip permit

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
27
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuring the 3G Wireless Modular and Fixed Cisco ISRs

Command or Action Purpose

Step 6 Router(config)# ip access-list<access list Defines traffic of interest.
number>permit <ip source address>

Note Do not use the access list permit all

Example:
Router(config)# access list 2 permit 10.4.0.0 command to avoid sending traffic to the IP
network. This may result in call termination.
Step 7 Router(config)# interface Enters the interface configuration mode.
cellular<slot/wic_slot/port>

Example:
Router(config)# interface cellular 0/1/0
Step 8 Router(config-if)# dialer-group <dialer group number> Maps a dialer list to the dialer interface.

Example:
Router(config-if)# dialer-group 2

Configuring DDR Backup Using Floating Static Route

To configure a floating static default route on the secondary interface beginning in the global
configuration mode, perform the following tasks.

Note Make sure you have ip classless enabled on your router.

SUMMARY STEPS

1. configure terminal
2. ip route network-number network-mask {ip address | interface} [administrative distance] [name
name]

DETAILED STEPS

Command or Action Purpose

Step 1 Router# configure terminal Enters global configuration mode from the terminal.

Example:
Router# configure terminal
Step 2 Router(config)# ip route network-number network-mask Establishes a floating static route with the
{ip-address | interface} [administrative distance] configured administrative distance through the
[name name]
specified interface.

Example:
Router (config)# ip route 0.0.0.0 Dialer 2 track 234 Note A higher administrative distance should be
configured for the route through the backup
interface, so that it is used only when the
primary interface is down.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
28
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuration Examples for the 3G Wireless Modular and Fixed Cisco ISRs

Configuring Multiple Mobile IP Profiles

This procedure is for the HWIC-3G-CDMA-S and HWIC-3G-CDMA SKUs only.

Note Please verify with your carrier if mobile IP is supported on your HWIC.

SUMMARY STEPS

1. cellular cdma profile configure

2. cellular cdma profile select

DETAILED STEPS

Command or Action Purpose

Step 1 Router# cellular <slot/wic/port> cdma profile Configures data (MIP) profile.
configure <profile number> <primary home agent
address> <secondary home agent address> <mobile home
agent address> <NAI> <MN-AAA SS> <MN-HA SS> <MN-AAA
SPI> <MN-HA SPI> <Reverse Tunneling Preference>
Note Parameters for this command may be
different for different SKUs. Please refer to
the cellular cdma profile configure
Example: command for details.
Router# cellular 0/0/0 cdma profile configure 1
1.1.1.1 2.2.2.2 3.3.3.3 test@xyz.com aaa bbb 1234
1234 1
Step 2 Router# cellular <slot/wic/port> cdma profile select Sets a profile as the current active profile.
<profile number>

Example:
Router# cellular 0/0/0 cdma profile select 1

Configuring Data DedicatedTransmission Mode (DDTM)

On CDMA modems, data transmission is disrupted by incoming voice calls if data dedicated
transmission mode (DDTM) is disabled. You can enable DDTM mode so the modem will ignore
incoming voice calls.
To enable dedicated data transmission mode (DDTM) on a CDMA modem, use the cdma ddtm
command in configuration mode
This command is enabled by default. You can disable this feature by using the no cdma ddtm command.

Note When DDTM is enabled, only voice calls will be blocked for the MC5728v modems, while on the
AC597E and MC5725 and MC 5727, incoming SMS messages will also be blocked.

Configuration Examples for the 3G Wireless Modular and Fixed

Cisco ISRs
This section provides the following configuration examples:

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
29
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuration Examples for the 3G Wireless Modular and Fixed Cisco ISRs

• Basic Cellular Interface Configuration: Example

• Tunnel over Cellular Interface Configuration: Example
• 3G Wireless Modem as Backup with NAT and IPSec: Example

Basic Cellular Interface Configuration: Example

The following is an example configuration where the cellular interface is used as a primary and is
configured as the default route:
chat-script cdma "" "ATDT#777" TIMEOUT 60 "CONNECT“

!
interface Cellular0/0/0
ip address negotiated
encapsulation ppp
dialer in-band
dialer string cdma
dialer-group 1
async mode interactive
ppp chap password 0 cisco
ppp ipcp dns request
!

!
!
access-list 1 permit any
dialer-list 1 protocol ip list 1
!
line 0/0/0
exec-timeout 0 0
script dialer cdma
login
modem InOut

Tunnel over Cellular Interface Configuration: Example

The following sample configuration shows the configuration of the static IP address when a tunnel
interface is configured using the ip address unnumbered <cellular interface> command:
interface Tunnel2
ip unnumbered GigabitEthernet0/1
tunnel source Cellular0/3/0
tunnel destination 128.107.248.254

interface Cellular0/3/0
!
ip address negotiated

encapsulation ppp

dialer in-band
dialer idle-timeout 0
dialer string cdma
dialer-group 1
async mode interactive

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
30
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuration Examples for the 3G Wireless Modular and Fixed Cisco ISRs

ppp chap password 0 cisco

ppp ipcp dns request

! traffic of interest through the tunnel/cellular interface

ip route 10.10.0.0 255.255.0.0 Tunnel2

3G Wireless Modem as Backup with NAT and IPSec: Example

The following sample configuration shows the configuration of the 3G wireless modem on the router as
backup with NAT and IPSec:
ip dhcp excluded-address 10.4.0.254
!
ip dhcp pool cdma-pool
network 10.4.0.0 255.255.0.0
default-router 10.4.0.254
!
chat-script cdma "" "atdt#777” TIMEOUT 20 "CONNECT"
!
track 234 rtr 1 reachability
!
crypto isakmp policy 1
encr 3des
authentication pre-share
!
crypto isakmp key mykey address 20.20.241.234
!
crypto ipsec transform-set mytransformset ah-sha-hmac esp-3des
!
crypto map vpn1 10 ipsec-isakmp
set peer 20.20.241.234
set transform-set mytransformset
match address 103
!
interface GigabitEthernet0/0
ip address 10.4.0.254 255.255.0.0
duplex auto
speed auto
!
interface ATM0/0/0
no ip address
ip virtual-reassembly
load-interval 30
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0/0/0.1 point-to-point
ip nat outside
ip virtual-reassembly
no snmp trap link-status
pvc 0/35
pppoe-client dial-pool-number 2
!
interface Cellular0/3/0
ip address negotiated
ip nat outside
encapsulation ppp

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
31
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuration Examples for the 3G Wireless Modular and Fixed Cisco ISRs

dialer in-band
dialer idle-timeout 0
dialer string cdma
dialer-group 1
ppp chap hostname host@apn
ppp chap password 0 cisco123
ppp ipcp dns request
crypto map vpn1
!
interface Dialer2
ip address negotiated
ip nat outside
encapsulation ppp
dialer pool 2
dialer-group 2
ppp chap hostname cisco@dsl.net
ppp chap password 0 cisco123
ppp pap sent-username Cisco@dsl.net password 0 cisco123
ppp ipcp dns request
crypto map vpn1
!
ip local policy route-map track-primary-if
!
ip route 0.0.0.0 0.0.0.0 Dialer2 track 234
!
ip route 0.0.0.0 0.0.0.0 Cellular0/3/0 254
!
ip nat inside source route-map nat2cell interface Cellular0/3/0 overload
ip nat inside source route-map nat2dsl interface Dialer2 overload
!
ip sla 1
icmp-echo 209.131.36.158 source-interface Dialer2
timeout 1000
frequency 2
ip sla schedule 1 life forever start-time now
!
access-list 1 permit any
access-list 101 deny ip 10.4.0.0 0.0.255.255 20.20.0.0 0.0.255.255
access-list 101 permit ip 10.4.0.0 0.0.255.255 any
!
access-list 102 permit icmp any host 209.131.36.158
!
access-list 103 permit ip 10.4.0.0 0.0.255.255 20.20.0.0 0.0.255.255
!
dialer-list 1 protocol ip list 1
dialer-list 2 protocol ip permit
!
route-map track-primary-if permit 10
match ip address 102
set interface Dialer2 null0
!
route-map nat2dsl permit 10
match ip address 101
match interface Dialer2
!
route-map nat2cell permit 10
match ip address 101
match interface Cellular0/3/0
!
event manager applet pri_back
event track 234 state any
action 2.0 cli command "clear ip nat trans forced"
!
line 0/3/0

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
32
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Configuration Examples for the 3G Wireless Modular and Fixed Cisco ISRs

script dialer cdma

modem InOut

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
33
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Modem Firmware Upgrade

Modem Firmware Upgrade

The 3G wireless Modular and Fixed Cisco ISR modem firmware can be upgraded by using Cisco IOS
commands. The firmware is packaged in a tar distribution file and can be downloaded from the wireless
software download page on Cisco.com. Use the following procedure to upgrade the modem firmware:

Caution Before upgrading the modem to a new firmware version, please check whether the new firmware version
has been certified by your wireless service provider. Using an uncertified firmware version on the
modem may affect the wireless service provider network adversely.

Note Perform modem upgrade only if necessary. Downgrade is generally not supported, and may or may not
work.

Refer to the following website for the latest certified firmware version for your carrier and IOS
compatibility:
http://www.cisco.com/en/US/products/hw/routers/networking_solutions_products_generic_content090
0aecd80601f7e.html

SUMMARY STEPS

1. Go to the CDMA/EVDO firmware download website at:

http://software.cisco.com/download/navigator.html?mdfid=279119319&flowid=6999
and in the third column, select Verizon or Sprint, depending on the type of card you have.
2. Download the appropriate CDMA firmware release under Wireless Integrated Switches and Routers.
3. Use the archive command to extract the firmware distribution into the router flash memory:
archive tar /xtract source-url destination-url
4. Use the following command to initiate the firmware upgrade process:
microcode reload cellular pa-bay slot cdma modem-provision

DETAILED STEPS

Command or Action Purpose

Step 1 Go to the Download Software site at: Provides access to Cisco Wireless WAN software
downloads. Select firmware for Cisco 3G wireless
http://software.cisco.com/download/navigator.html
Modular and Fixed Cisco ISRs.
and select Wireless > Wireless Integrated Switches and
Routers. In the third column, select Verizon or Sprint, Note This website is only available to registered
depending on the type of card you have. Cisco.com users.

Step 2 Download the appropriate CDMA firmware release Downloads the modem firmware package to a
under Wireless Integrated Switches and Routers. TFTP/FTP server that is accessible from the router
in which the 3G wireless Modular and Fixed Cisco
ISRs is installed.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
34
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Command Reference

Command or Action Purpose

Step 3 router# archive tar /xtract source-url Uncompresses the files of the modem firmware
destination-url package and copies them to a location that is
accessible by the router in which the 3G wireless
Modular and Fixed Cisco ISR is installed.
Example: source-url—URL of the source location with the
Router# archive tar /xtract
firmware TAR filename. Valid URLs can refer to
tftp://192.168.1.1/MC5725_00_57_00_vzw_package.t
ar flash: TFTP or HTTP servers or to router flash memory.
destination-url—URL of the destination where the
tar file would be extracted. Use router flash.
Step 4 router# microcode reload cellular pa-bay slot Initiates the firmware upgrade process.
cdma modem-provision
pa-bay—Use 0 for HWIC.
slot—Slot number where the HWIC is plugged in.

Note This command automatically shuts down the

cellular interface. The firmware upgrade
process may take up to 15 minutes, during
which the modem is inaccessible. After the
command is complete, the interface is
brought up again.

Caution Do not disconnect power or switch the router off during the firmware upgrade process. Either action may
result in permanent modem failure.

Command Reference
This section documents new commands only.
• cdma ddtm
• cellular cdma activate iota
• cellular cdma activate manual
• cellular cdma activate oma-dm device config
• cellular cdma activate oma-dm ni-alert
• cellular cdma activate oma-dm prl-update
• cellular cdma activate otasp
• cellular cdma mode
• cellular cdma profile configure
• cellular cdma profile select
• debug cell-hwic driver

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
35
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Command Reference

• debug cell-hwic firmware

• debug cell-hwic virt-con
• debug cellular messages all
• debug cellular messages async
• debug cellular messages data
• debug cellular messages dm
• debug cellular messages management
• debug cellular messages oma-dm
• show cellular all
• show cellular connection
• show cellular connection
• show cellular hardware
• show cellular network
• show cellular oma-dm
• show cellular profile
• show cellular radio
• show cellular security
• show controllers cellular
• show interfaces cellular
• show run interface cellular

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
36
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cdma ddtm

cdma ddtm
On CDMA modems, data transmission is disrupted by incoming voice calls if data dedicated
transmission mode (DDTM) is disabled. You can enable DDTM mode so the modem will ignore
incoming voice calls.
To enable DDTM on a CDMA modem, use the cdma ddtm command in configuration mode.

cdma ddtm

To disable DDTM, use the no form of this command.

Command Default DDTM is enabled by default.

Command Modes Configuration.

Command History Release Modification

15.1(4)M1 This command was introduced.

Usage Guidelines Disable this feature only if you require the voice-initiated data callback feature.

Examples The following example shows the configuration to enable the cdma ddtm command:
Router(config)#controller cellular 0/0
Router(config-controller)#cdma ddtm

The following example shows how to configure the no cdma ddtm command:
Router(config)#controller cellular 0/0
Router(config-controller)#no cdma ddtm
Router(config-controller)#end

The following output for the show cellular connection command shows that DDTM is enabled:

Router#show cellular 0/0/0 connection

Phone number of outgoing call =
HDR AT State = Inactive, HDR Session State = Close
HDR Session Info:
UATI (Hex) = 0000:0000:0000:0000:0000:0000:0000:0000
Color Code = 0, RATI = 0x0
Session duration = 0 msecs, Session start = 0 msecs
Session end = 0 msecs, Authentication Status = Not authenticated
HDR DRC Value = 0, DRC Cover = 0, RRI = Pilot only
Current Transmitted = 0 bytes, Received = 0 bytes
Total Transmitted = 0 KB, Received = 0 KB
Current Call Status = None
Current Call Duration = 0 secs
Total Call Duration = 376179855 seconds
Current Call Type =
Last Call Disconnect Reason = Modem offline
Last Connection Error = None

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
37
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cdma ddtm

HDR DDTM (Data Dedicated Transmission Mode) Preference = On

Mobile IP Error Code (RFC-2002) = 0 (Registration accepted)

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
38
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate iota

cellular cdma activate iota

To periodically refresh the modem data profile using Internet-based over-the-air provisioning (IOTA),
use the cellular cdma activate iota command in privileged EXEC mode. IOTA is used to activate the
modem data profile by certain wireless service providers. Use this command to display the current active
connection state and statistics. (Ask your carrier whether IOTA is supported and how often a refresh is
needed.)

cellular slot/wic_slot/port cdma activate iota

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None.

Command Modes EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines You can verify the updated modem data profile by using the show cellular slot/wic_slot/port profile
command.

Note Use this command only if you are using an HWIC-3G-CDMA-S interface card.

Examples The following example shows output from the cellular cdma activate iota command:
router # cellular 0/0/0 cdma activate iota
Begin IOTA
router#
*Feb 6 23:32:21.339: IOTA Status Message Received. Event: IOTA Start, Result: SUCCESS
*Feb 6 23:32:21.339: Please wait till IOTA END message is received
*Feb 6 23:32:21.339: It can take up to 5 minutes
*Feb 6 23:32:40.867: OTA State = SPL unlock, Result = Success
*Feb 6 23:32:45.235: OTA State = Parameters commited to NVRAM, Result = Success
*Feb 6 23:32:52.087: Over the air provisioning complete; Result:Success
*Feb 6 23:32:52.615: IOTA Status Message Received. Event: IOTA End, Result: SUCCESS

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
39
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate iota

Related Commands Command Description

cellular cdma activate manual Manually activates a cellular account using the over the air service
(OTA) procedure.
show cellular profile Displays the cellular profile information.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
40
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate manual

cellular cdma activate manual

To manually activate the modem, use the cellular cdma activate manual command in privileged EXEC
mode.

Note The modem activation process is specific to the carrier. Ask your carrier whether manual
activation—using MDN, MSID, and MSN—or activation using over-the-air service provisioning
(OTASP) is supported.

cellular slot/wic_slot/port cdma activate manual mdn msid sid nid msl

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.
mdn Ten digit mobile directory number (MDN).
msid Ten digit mobile subscriber identification number (MSID).
sid System ID (SID) number between 0 and 32767.
Note Use the show cellular network command to obtain the system ID.
nid Network ID (NID) number between 0 and 65535.
Note Use the show cellular network command to obtain the network ID.
msl Mobile subscriber lock, to be obtained from your service provider.

Command Default None.

Command Modes EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines Use the show cellular network command to obtain the SID and NID.
You can verify whether the modem has been activated using the show cellular slot/wic_slot/port all
command.

Note Use this command only if you have an HWIC-3G-CDMA-S interface card.

Examples The following is sample output from the cellular cdma activate manual command:
router# cellular 0/0/0 cdma activate manual 9135938079 9135938079 4183 87 907148

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
41
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate manual

NAM 0 will be configured and will become Active

Modem will be activated with following Parameters
MDN :9135938079; MSID :9135938079; SID :4183; NID 87:
Checking Current Activation Status
Modem activation status: Not Activated
Begin Activation
Account activation - Step 1 of 5
Account activation - Step 2 of 5
Account activation - Step 3 of 5
Account activation - Step 4 of 5
Account activation - Step 5 of 5
Secure Commit Result: Succeed
Done Configuring - Resetting the modem
The activation of the account is Complete
Waiting for modem to be ready to start IOTA
Beginning IOTA
router#
*Feb 6 23:29:08.459: IOTA Status Message Received. Event: IOTA Start, Result: SUCCESS
*Feb 6 23:29:08.459: Please wait till IOTA END message is received
*Feb 6 23:29:08.459: It can take up to 5 minutes
*Feb 6 23:29:27.951: OTA State = SPL unlock, Result = Success
*Feb 6 23:29:32.319: OTA State = Parameters commited to NVRAM, Result = Success
*Feb 6 23:29:40.999: Over the air provisioning complete; Result:Success
*Feb 6 23:29:41.679: IOTA Status Message Received. Event: IOTA End, Result: SUCCESS

The following is sample output from the show cellular profile command after the modem has been
activated:
router# show cellular 0/3/0 profile

Profile Information
====================
Electronic Serial Number (ESN) = 0x603C6426
Modem activated = YES

Account Information:
======================
Activation Date: 20070221
Phone Number (MDN) : 2029976763
Mobile Station Identifier (MSID) : 2029976763

Data Profile Info:

=====================
Number of data profiles configured : 1
Current active data profile : 0

Data Profile 0 Information (Active)

==================================
NAI (Network Access Identifier) = 2029976763@vzw3g.com
MN-HA SS = Set
MN-HA SPI = 300
MN-AAA SS = Set
MN-AAA SPI = 2
Reverse Tunneling Preference = Set
Home Address = 0.0.0.0
Primary Home Agent Address = 255.255.255.255
Secondary Home Agent Address = 255.255.255.255

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
42
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate manual

Related
Commands Command Description
cellular cdma activate iota Manually activates a cellular account using the Internet
over-the-air service procedure.
show cellular profile Displays the cellular profile information.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
43
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate oma-dm device config

cellular cdma activate oma-dm device config

To start a user-initiated OMA-DM session to provision an account and MIP1 (Mobile IP) profile update,
use the cellular cdma activate oma-dm device config command in privileged EXEC mode.

cellular slot/wic_slot/port cdma activate oma-dm device config

This refreshes the MDN and MSID numbers on the account.

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(22)YB1 This command was introduced.

Usage Guidelines Before you execute this command, terminate any existing active or dormant data connection. The modem
is activated automatically when it powers up using Hands Free Activation. Use this command only when
activation fails or you need to update your account parameters.
To view profile and MIB information, use the show cellular profile command.

Examples This section contains sample output for cellular slot/wic_slot/port cdma activate oma-dm
device-config command:

Sample Output for HWIC-3G-CDMA

The following example shows output for HWIC-3G-CDMA for slot 0, WIC slot 0, port 0:
Router#cellular 0/0/0 cdma activate oma-dm device-config
Modem is activated
MIP profile 1 will be updated and will be active, if command is successful
Beginning OMA-DM.

Router#
*Feb 5 20:50:18.207: %CELLWAN-2-OMA_DM_ACTIVE: [Cellular0/0/0]: OMA DM Device
Configuration session is active
Router_1841_Live#
*Feb 5 20:50:34.755: %CELLWAN-2-OMA_DM_SUCCESS: [Cellular0/0/0]: OMA DM Device
Configuration completed successfully

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
44
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate oma-dm device config

Related Commands Command Description

show cellular oma-dm Displays an OMA-DM session details.
cellular cdma activate oma-dm Allows or denies a network initiated alert (NIA) queued in the
ni-alert modem.
cellular cdma activate oma-dm Starts a user initiated OMA-DM session to get an over-the-air PRL
prl-update update.
debug cellular messages Starts OMA-DM debugging.
oma-dm
show cellular profile Displays cellular profile information.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
45
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate oma-dm ni-alert

cellular cdma activate oma-dm ni-alert

To allow or deny a network initiated alert (NIA) queued in the modem, use the cellular cdma activate
oma-dm ni-alert [allow | deny] command in privileged EXEC mode.

cellular slot/wic_slot/port cdma activate oma-dm ni-alert [allow | deny]

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.
allow Allow a network initiated alert.
deny Deny a network initiated alert.

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(22)YB1 This command was introduced.

Usage Guidelines On execution of this command, a warning message appears that the current data connection will be
interrupted. You must confirm if you want to proceed with this command.

Note If you deny the NIA, depending on the SKU of the modem, the NIA may be available for a later attempt
or permanently deleted from the system.

Examples This section contains sample output for cellular slot/wic_slot/port cdma activate oma-dm ni-alert
command:

Sample Output for HWIC-3G-CDMA

The following example shows output for HWIC-3G-CDMA for slot 0, WIC slot 0, port 0 with Network
Initiated Alert while the modem is in dormant state (cellular slot/wic_slot/port cdma activate oma-dm
ni-alert allow):

*Feb 5 20:57:04.827: %CELLWAN-2-OMA_DM_NI_ALERT: [Cellular0/0/0]: OMA DM NI Alert is

received for Device Configuration
Please execute 'cellular <unit> cdma activate oma-dm ni-alert [allow | deny]'
Router#cellular 0/0/0 cdma activate oma-dm ni-alert allow
Modem is activated
!!!WARNING: Data connection will be terminated. Service will be interrupted until the NI
session is completed.
Are you sure?(y/n) [confirm]

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
46
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate oma-dm ni-alert

[Cellular0/0/0]:The interface will be shutdown to allow the Network-Initiated OMA DM

session. This will terminate any active data connection.

OMA DM NI alert: Interactive response accepted

*Feb 5 20:57:19.611: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0/0/0,

changed state to down
*Feb 5 20:57:20.627: %LINK-5-CHANGED: Interface Cellular0/0/0, changed state to
administratively down
*Feb 5 20:57:26.063: %CELLWAN-2-OMA_DM_ACTIVE: [Cellular0/0/0]: OMA DM Device
Configuration session is active

*Feb 5 20:57:36.847: %CELLWAN-2-OMA_DM_SUCCESS: [Cellular0/0/0]: OMA DM Device

Configuration completed successfully

The following example shows output for HWIC-3G-CDMA for slot 0, WIC slot 0, port 0 for the
cellular slot/wic_slot/port cdma activate oma-dm ni-alert deny command:

*Feb 5 21:01:08.487: %CELLWAN-2-OMA_DM_NI_ALERT: [Cellular0/0/0]: OMA DM NI Alert is

received for Device Configuration
Please execute 'cellular <unit> cdma activate oma-dm ni-alert [allow | deny]'

Enzo-sustaining_1841_Live#cellular 0/0/0 cdma activate oma-dm ni-alert deny

Modem is activated
OMA DM NI alert: Interactive response accepted

Table 19 describes the output fields from the command.

Table 10 Field Description

Field Description
Interactive response accepted The alert response is accepted by the modem. You
will see OMA-DM status messages in SYSLOG
or console.
Fail: Interactive response not expected No alert queued in the modem.
Fail: Invalid response Not a valid response.

Related Commands Command Description

show cellular oma-dm Displays an OMA-DM session details.
cellular cdma activate oma-dm Starts a user initiated OMA-DM session to provision an account
device config and profile update.
cellular cdma activate oma-dm Starts a user initiated OMA-DM session to get an over-the-air PRL
prl-update update.
debug cellular messages Starts OMA-DM debugging.
oma-dm
show cellular profile Displays cellular profile information.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
47
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate oma-dm prl-update

cellular cdma activate oma-dm prl-update

To start a user initiated OMA-DM session to get an over-the-air PRL update, use the cellular cdma
activate oma-dm prl-update command in privileged EXEC mode.

cellular slot/wic_slot/port cdma activate oma-dm prl-update

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(22)YB1 This command was introduced.

Usage Guidelines PRL upates are available periodically by the Service Provider. If no updates are available, an empty
session error message is returned.

Note If the PRL is updated successfully, the modem will be reset.

Examples This section contains sample output for cellular slot/wic_slot/port cdma activate oma-dm prl-update
command:

Sample Output for HWIC-3G-CDMA

The following example shows output for HWIC-3G-CDMA for slot 0, WIC slot 0, port 0 when the
update is successful:
Router#cellular 0/0/0 cdma activate oma-dm prl-update
Modem is activated
Beginning OMA-DM
*Jan 27 18:32:08.087: %CELLWAN-2-OMA_DM_ACTIVE: [Cellular0/0/0]: OMA DM PRL Update session
is active
*Jan 27 18:32:31.643: %CELLWAN-2-OMA_DM_SUCCESS: [Cellular0/0/0]: OMA DM PRL Update
completed successfully

The following example shows output for HWIC-3G-CDMA for slot 0, WIC slot 0, port 0 when the
update is unsuccessful:

Router#cellular 0/0/0 cdma activate oma-dm prl-update

Modem is activated
Beginning OMA-DM.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
48
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate oma-dm prl-update

*Feb 5 21:33:23.795: %CELLWAN-2-OMA_DM_ACTIVE: [Cellular0/0/0]: OMA DM PRL Update session

is active
*Feb 5 21:34:03.587: %CELLWAN-2-OMA_DM_ERROR: [Cellular0/0/0]: OMA DM PRL Update Failed -
Error:0x504(Unrecoverable network error)

Related Commands Command Description

show cellular oma-dm Displays an OMA-DM session details.
cellular cdma activate oma-dm Allows or denies a network initiated alert (NIA) queued in the
ni-alert modem.
cellular cdma activate oma-dm Starts a user initiated OMA-DM session to provision an account
device config and profile update.
debug cellular messages Starts OMA-DM debugging.
oma-dm
show cellular profile Displays cellular profile information.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
49
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate otasp

cellular cdma activate otasp

To activate a wireless account using over-the-air service provisioning (OTASP), use the cellular cdma
activate otasp command in privileged EXEC mode.

Note The modem activation process is specific to the carrier. Check with your carrier if they support manual
activation—using MDN, MSID, and MSN—or activation using OTASP.

cellular slot/wic_slot/port cdma activate otasp phone_number

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.
phone_number Phone number that you must dial to begin activation using OTASP. This
number is specific to a wireless provider. For Verizon Wireless, it is *22899.

Command Default None.

Command Modes Privileged EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines You can verify the modem activation using the show cellular slot/wic_slot/port all command.

Note Use this command only if you are using an HWIC-3G-CDMA-V interface card.

Examples The following example shows output of the cellular cdma activate otasp command:
router# cellular 0/1/0 cdma activate otasp *22899

Beginning OTASP activation

OTASP number is *22899
router#
*Feb 6 23:18:45.393: OTA State = SPL unlock, Result = Success
*Feb 6 23:19:10.229: OTA State = PRL downloaded, Result = Success
*Feb 6 23:19:11.169: OTA State = Profile downloaded, Result = Success
*Feb 6 23:19:11.173: OTA State = MDN downloaded, Result = Success
*Feb 6 23:19:12.537: OTA State = Parameters commited to NVRAM, Result = Success
*Feb 6 23:19:14.613: Over the air provisioning complete; Result:Success

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
50
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma activate otasp

The following is a sample output from the show cellular profile command after the modem has been
activated:
router#show cellular 0/3/0 profile

Profile Information
====================
Electronic Serial Number (ESN) = 0x603C6426
Modem activated = YES

Account Information:
======================
Activation Date: 20070221
Phone Number (MDN) : 2029976763
Mobile Station Identifier (MSID) : 2029976763

Data Profile Info:

=====================
Number of data profiles configured : 1
Current active data profile : 0

Data Profile 0 Information (Active)

==================================
NAI (Network Access Identifier) = 2029976763@vzw3g.com
MN-HA SS = Set
MN-HA SPI = 300
MN-AAA SS = Set
MN-AAA SPI = 2
Reverse Tunneling Preference = Set
Home Address = 0.0.0.0
Primary Home Agent Address = 255.255.255.255
Secondary Home Agent Address = 255.255.255.255

Related Commands Command Description

show cellular profile Displays the cellular profile information.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
51
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma mode

cellular cdma mode

To configure the modem mode to connect to 1xRTT, EVDO or hybrid services, use the cellular cdma
mode command in privileged EXEC mode.

cellular slot/wic_slot/port cdma mode <hybrid | EVDO-only | 1xRTT-only>

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.
hybrid Connect to EVDO/1xRTT services (Default Mode)
EVDO-only Connect only to EVDO service
1xRTT-only Connect only to 1xRTT service

Command Default Hybrid

Command Modes Privileged EXEC

Command History Release Modification

12.4(22)YB1 This command was introduced.

Usage Guidelines This command is executed only upon confirmation from the user. A service mode change is followed by
a modem reset.

Examples This section contains sample output for cellular slot/wic_slot/port cdma mode command:

Sample Output for HWIC-3G-CDMA

The following example shows output for HWIC-3G-CDMA for slot 0, WIC slot 1, port 1:
Router#cellular 0/0/0 cdma mode ?
1xRTT Modem will connect to 1xRTT only service
evdo Modem will connect to EVDO only service
hybrid Modem will connect to EVDO and 1xRTT service (default behavior)

Table 19 describes the output fields from the command.

Table 11 Field Description

Field Description
1xRTT Modem will connect to 1xRTT only service
EVDO Modem will connect to EVDO only service
Hybrid Modem will connect to EVDO and 1xRTT service
(default)

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
52
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma mode

Related Commands Command Description

cellular cdma activate manual Manually activates a cellular account using the over-the-air service
(OTA) procedure.
cellular cdma activate otasp Activates a cellular account using the over the air service
provisioning (OTASP).
cellular cdma activate iota Provisions data profile using Internet-based over-the-air
provisioning (IOTA).
Note IOTA is supported only with certain wireless service
providers. Please check with your wireless service
provider.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
53
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma profile configure

cellular cdma profile configure

To manipulate CDMA modem data profile information, use the cellular cdma profile configure
command in privileged EXEC mode.

cellular slot/wic_slot/port cdma profile configure <profile number> <primary HA address>

<secondary HA address><mobile HA><NAI> <MN-AAA SS> <MN-HA SS> <MN-AAA
SPI><MN-HA SPI> <rev-tunneling>

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.
profile number Profile number to be configured
primary HA address Primary Home Agent Address as obtained from Service Provider
secondary HA address Secondary Home Agent Address as obtained from Service Provider
mobile HA* Mobile Home Agent. This parameter is only needed for generic SKUs.
NAI Network Access Identifier
MN-AAA SS Mobile Node AAA Shared Secret
MN-HA SS Mobile Node Home Agent shared secret
MN-AAA SPI* Mobile Node AAA Security Parameter Index
MN-HA SPI* Mobile Node Home Agent Security Parameter Index
rev-tunneling* Reverse tunneling preference
* denotes parameters not available in HWIC-3G-CDMA-S

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(22)YB1 This command was introduced.

Usage Guidelines This command is not supported for the HWIC-3G-CDMA-V SKU.

Examples This section contains sample output for cellular slot/wic_slot/port cdma profile configure command:

Sample Output for HWIC-3G-CDMA

router#cellular 0 cdma profile configure ?
<1-5> profile number
router#cellular 0 cdma profile configure 5 ?
A.B.C.D Primary HA Address
router#cellular 0 cdma profile configure 5 100.1.1.1 ?
A.B.C.D Secondary HA Address

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
54
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma profile configure

router#cellular 0 cdma profile configure 5 100.1.1.1 200.1.1.1 ?

WORD Network Access Identifier (Ex:username@domain)
router#$le configure 5 100.1.1.1 200.1.1.1 testing@sp.com ?
WORD MN-AAA Shared Secret
router#$le configure 5 100.1.1.1 200.1.1.1 testing@sp.com kkk ?
WORD MN-HA Shared Secret
router#$le configure 5 100.1.1.1 200.1.1.1 testing@sp.com kkk mmm ?
<cr>
router#$le configure 5 100.1.1.1 200.1.1.1 testing@sp.com kkk mmm
Profile 5 will be configured with following parameters:
NAI (Network Access Identifier) = testing@sp.com
Home Address = 0.0.0.0
Primary Home Agent Address = 100.1.1.1
Secondary Home Agent Address = 200.1.1.1
MN-AAA SS = Set
MN-HA SS = Set
MN-AAA SPI = 1234
MN-HA SPI = 1234
Reverse Tunneling Preference = Set
!!!WARNING: Modem will be reset
Are you sure? [confirm]
Done configuring - Please wait while the modem resets
*Feb 25 21:21:37.504: %CISCO800-2-MODEM_REMOVAL_DETECTED: Cellular0 modem is now REMOVED
*Feb 25 21:21:37.504: %CISCO800-2-CELLULAR_INTERFACE_NOT_SHUTDOWN: WARNING: Cellular0
interface should be shutdown before removing modem. Reload Required to reset interface
*Feb 25 21:21:38.508: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0, changed
state to down
*Feb 25 21:21:43.264: %CELLWAN-2-HEART_BEAT_TIMEOUT: No heart beat signal from Cellular0
*Feb 25 21:21:43.540: %CISCO800-2-MODEM_INSERTED_DETECTED: Cellular0 modem is now INSERTED
*Feb 25 21:21:43.544: %CELLWAN-2-MODEM_DOWN: Cellular0 modem is DOWN
*Feb 25 21:21:45.540: %LINK-5-CHANGED: Interface Cellular0, changed state to reset
Profile 5 configured successfully
router#
router#
*Feb 25 21:21:48.648: %CELLWAN-2-MODEM_UP: Cellular0 modem is now UP
router#
router#sh
*Feb 25 21:21:50.540: %LINK-3-UPDOWN: Interface Cellular0, changed state to down
router#show cellu
router#show cellular 0 p
router#show cellular 0 profile 5
Electronic Serial Number (ESN) = 0x605F6982 [09606252930]
Modem activated = YES
Account Information:
======================
Activation Date: Not available
Phone Number (MDN) : 4084205046
Mobile Station Identifier (MSID) : 4084205046
Data Profile Info:
=====================
Number of data profiles configurable : 5
Current active data profile : 1
Data Profile 5 Information
==================================
NAI (Network Access Identifier) = testing@sp.com
MN-HA SS = Set
MN-HA SPI = 1234
MN-AAA SS = Set
MN-AAA SPI = 1234
Reverse Tunneling Preference = Set
Home Address = 0.0.0.0
Primary Home Agent Address = 100.1.1.1
Secondary Home Agent Address = 200.1.1.1
router#

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
55
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma profile configure

Related Commands Command Description

cellular cdma activate manual Manually activates a cellular account using the over-the-air service
(OTA) procedure.
cellular cdma activate otasp Activates a cellular account using the over the air service
provisioning (OTASP).
cellular cdma activate iota Provisions data profile using Internet-based over-the-air
provisioning (IOTA).
Note IOTA is supported only with certain wireless service
providers. Please check with your wireless service
provider.
cellular cdma activate oma-dm Starts a user-initiated OMA-DM session for modem activation.
device config
Note IOTA is supported only with certain wireless service
providers. Please check with your wireless service
provider.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
56
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma profile select

cellular cdma profile select

To select a CDMA modem data profile, use the cellular cdma profile select command in privileged
EXEC mode.

cellular slot/wic_slot/port cdma profile select <profile number> <primary HA address>

<secondary HA address><mobile HA><NAI> <MN-AAA SS> <MN-HA SS> <MN-AAA
SPI><MN-HA SPI> <rev-tunneling>

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.
profile number Profile number to be configured
primary HA address Primary Home Agent Address as obtained from Service Provider
secondary HA address Secondary Home Agent Address as obtained from Service Provider
mobile HA* Mobile Home Agent. This parameter is only needed for generic SKUs.
NAI Network Access Identifier
MN-AAA SS Mobile Node AAA Shared Secret
MN-HA SS Mobile Node Home Agent shared secret
MN-AAA SPI* Mobile Node AAA Security Parameter Index
MN-HA SPI* Mobile Node Home Agent Security Parameter Index
rev-tunneling* Reverse tunneling preference
* denotes parameters not available in HWIC-3G-CDMA-S

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(22)YB1 This command was introduced.

Usage Guidelines This command is not supported for the HWIC-3G-CDMA-V SKU.

Examples This section contains sample output for cellular slot/wic_slot/port cdma profile select command:

Sample Output for HWIC-3G-CDMA

router#cellular 0 cdma profile select 5 ?

<cr>
router#cellular 0 cdma profile select 5
Profile 5 will become active

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
57
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
cellular cdma profile select

!!!WARNING: Modem will be reset

Are you sure? [confirm]
Done configuring - Please wait while the modem resets
*Feb 25 21:23:58.224: %CISCO800-2-MODEM_REMOVAL_DETECTED: Cellular0 modem is now REMOVED
*Feb 25 21:23:58.224: %CISCO800-2-CELLULAR_INTERFACE_NOT_SHUTDOWN: WARNING: Cellular0
interface should be shutdown before removing modem. Reload Required to reset interface
*Feb 25 21:23:58.232: %CELLWAN-2-MODEM_DOWN: Cellular0 modem is DOWN
*Feb 25 21:23:59.784: %CISCO800-2-MODEM_INSERTED_DETECTED: Cellular0 modem is now INSERTED
*Feb 25 21:24:04.900: %CELLWAN-2-MODEM_UP: Cellular0 modem is now UP
Profile 5 selected successfully
router#
router#
router#
router#
router#show cellular 0 profile 5
Electronic Serial Number (ESN) = 0x605F6982 [09606252930]
Modem activated = YES
Account Information:
======================
Activation Date: Not available
Phone Number (MDN) : 4084205046
Mobile Station Identifier (MSID) : 4084205046
Data Profile Info:
=====================
Number of data profiles configurable : 5
Current active data profile : 5
Data Profile 5 Information (Active)
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
==================================
NAI (Network Access Identifier) = testing@sp.com
MN-HA SS = Set
MN-HA SPI = 1234
MN-AAA SS = Set
MN-AAA SPI = 1234
Reverse Tunneling Preference = Set
Home Address = 0.0.0.0
Primary Home Agent Address = 100.1.1.1
Secondary Home Agent Address = 200.1.1.1
router#

Related Commands Command Description

cellular cdma activate iota Provisions data profile using Internet-based over-the-air
provisioning (IOTA).
Note IOTA is supported only with certain wireless service
providers. Please check with your wireless service
provider.
cellular cdma activate manual Manually activates a cellular account using the over-the-air service
(OTA) procedure.
cellular cdma activate oma-dm Starts a user-initiated OMA-DM session for modem activation.
device config
Note IOTA is supported only with certain wireless service
providers. Please check with your wireless service
provider.
cellular cdma activate otasp Activates a cellular account using the over the air service
provisioning (OTASP).

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
58
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
debug cell-hwic driver

debug cell-hwic driver

To debug the Cisco IOS driver for the cellular interface, use the debug cell-hwic driver command in
EXEC mode.

debug cell-hwic slot/wic_slot/port driver {crcdump | errdump | errors}

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.
crcdump CRC error details.
errdump Other error details.
errors Errors debugging.

Command Default None

Command Modes EXEC (#)

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.
12.2SX This command is supported in the Cisco IOS Release 12.2SX train. Support
in a specific 12.2SX release of this train depends on your feature set,
platform, and platform hardware.

Usage Guidelines Use this command for debugging purposes only.

Related Commands Command Description

debug cellular messages async Debugs cellular async.
debug cellular messages data Prints Cisco IOS data path debug messages.
debug cellular firmware Displays Cisco IOS firmware information.
debug cellular messages Prints management path messages, such as CnS.
management
debug cellular messages dm Prints diagnostics monitor (DM) messages from the Qualcomm
CDMA chipset.
debug cell-hwic virt-con Redirects the Nios II console driver messages to display them in the
Cisco IOS router console environment.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
59
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
debug cell-hwic firmware

debug cell-hwic firmware

To see the Cisco IOS firmware information, use the debug cell-hwic firmware command in EXEC
mode.

debug cellular slot/wic_slot/port firmware

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.
12.4(22)YB1 This command was integrated into Cisco IOS Release 12.4(22)YB1.

Usage Guidelines Use this command for debugging purposes only.

Related Commands Command Description

debug cellular messages async Debugs cellular async.
debug cellular messages data Prints Cisco IOS data path debug messages.
debug cell-hwic driver Debugs the Cisco IOS driver.
debug cellular messages Prints management path messages, such as CnS.
management
debug cellular messages dm Prints diagnostics monitor (DM) messages from the Qualcomm
CDMA chipset.
debug cell-hwic virt-con Redirects the Nios II console driver messages to display them in the
Cisco IOS router console environment.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
60
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
debug cell-hwic virt-con

debug cell-hwic virt-con

To redirect the Nios II console driver messages to display them in the Cisco IOS router console
environment, use the debug cell-hwic virt-con command in EXEC mode.

debug cell-hwic slot/wic_slot/port virt-con {clear | disable | dump-data-structs | log | monitor |

wrapper-on | wrapper-off}

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.
clear (Optional) Clears all virtual console debug log messages.
disable (Optional) Disables virtual console real-time debug monitoring.
dump-data-structurs (Optional) Dumps virtual console data structures.
log (Optional) Displays virtual console messages from the debug log.
monitor (Optional) Enables monitoring of real-time virtual console debug messages.
wrapper-on (Optional) Disables wraparound for virtual console log messages.
wrapper-off (Optional) Enables wraparound for virtual console log messages.

Command Default There is no default for this command.

Command Modes EXEC (#)

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.
12.2SX This command is supported in the Cisco IOS Release 12.2SX train. Support
in a specific 12.2SX release of this train depends on your feature set,
platform, and platform hardware.
12.4(22)YB1 This command was integrated into Cisco IOS Release 12.4(22)YB1.

Usage Guidelines Use this command for debugging purposes only.

Related Commands Command Description

debug cellular messages all Prints all Cisco IOS driver debug messages.
debug cellular messages async Debugs cellular async.
debug cellular messages data Prints Cisco IOS data path debug messages.
debug cell-hwic driver Debugs the Cisco IOS driver.
debug cell-hwic firmware Displays Cisco IOS firmware information.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
61
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
debug cell-hwic virt-con

Command Description
debug cellular messages Prints management path messages, such as CnS.
management
debug cellular messages dm Prints diagnostics monitor (DM) messages from the Qualcomm
CDMA chipset.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
62
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
debug cellular messages all

debug cellular messages all

To print all Cisco IOS driver debug messages, use the debug cellular messages all command in EXEC
mode.

debug cellular slot/wic_slot/port messages all

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines Use this command for debugging purposes only.

Related Commands Command Description

debug cellular messages async Debugs cellular async.
debug cellular messages data Prints Cisco IOS data path debug messages.
debug cellular driver Debugs the Cisco IOS driver.
debug cellular firmware Displays Cisco IOS firmware information.
debug cellular messages Prints management path messages, such as CnS.
management
debug cellular messages dm Prints diagnostics monitor (DM) messages from the Qualcomm
CDMA chipset.
debug cellular messages Redirects the Nios II console driver messages to display them in the
virt-con Cisco IOS router console environment.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
63
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
debug cellular messages async

debug cellular messages async

To debug cellular async, use the debug cellular messages async command in EXEC mode.

debug cellular slot/wic_slot/port messages async

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines Use this command for debugging purposes only.

Related Commands Command Description

debug cellular messages all Prints all Cisco IOS driver debug messages.
debug cellular messages data Prints Cisco IOS data path debug messages.
debug cellular driver Debugs the Cisco IOS driver.
debug cellular firmware Displays Cisco IOS firmware information.
debug cellular messages Prints management path messages, such as CnS.
management
debug cellular messages dm Prints diagnostics monitor (DM) messages from the Qualcomm
CDMA chipset.
debug cellular messages Redirects the Nios II console driver messages to display them in the
virt-con Cisco IOS router console environment.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
64
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
debug cellular messages data

debug cellular messages data

To print Cisco IOS data path debug messages, use the debug cellular messages data command in EXEC
mode.

show cellular slot/wic_slot/port messages data

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines Use this command for debugging purposes only.

Related Commands Command Description

debug cellular messages all Prints all Cisco IOS driver debug messages.
debug cellular messages async Debugs cellular async.
debug cellular driver Debugs the Cisco IOS driver.
debug cellular firmware Displays Cisco IOS firmware information.
debug cellular messages Prints management path messages, such as CnS.
management
debug cellular messages dm Prints diagnostics monitor (DM) messages from the Qualcomm
CDMA chipset.
debug cellular messages Redirects the Nios II console driver messages to display them in the
virt-con Cisco IOS router console environment.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
65
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
debug cellular messages dm

debug cellular messages dm

To print Diagnostics Monitor (DM) messages from the Qualcomm CDMA chipset, use the debug
cellular messages dm command in EXEC mode.

debug cellular slot/wic_slot/port messages dm

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default There is no default for this command.

Command Modes EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines Use this command for debugging purposes only.

Related Commands Command Description

debug cellular messages all Prints all Cisco IOS driver debug messages.
debug cellular messages async Debugs cellular async.
debug cellular messages data Prints Cisco IOS data path debug messages.
debug cellular driver Debugs the Cisco IOS driver.
debug cellular firmware Displays Cisco IOS firmware information.
debug cellular messages Prints management path messages, such as CnS.
management
debug cellular messages Redirects the Nios II console driver messages to display them in the
virt-con Cisco IOS router console environment.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
66
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
debug cellular messages management

debug cellular messages management

To print management path messages, such as CnS, use the debug cellular messages management
command in EXEC mode.

debug cellular slot/wic_slot/port messages management

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines Use this command for debugging purposes only.

Related Commands Command Description

debug cellular messages all Prints all Cisco IOS driver debug messages.
debug cellular messages async Debugs cellular async.
debug cellular messages data Prints Cisco IOS data path debug messages.
debug cellular driver Debugs the Cisco IOS driver.
debug cellular firmware Displays Cisco IOS firmware information.
debug cellular messages Redirects the Nios II console driver messages to display them in the
virt-con Cisco IOS router console environment.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
67
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
debug cellular messages oma-dm

debug cellular messages oma-dm

To start OMA-DM debugging, use the debug cellular messages oma-dm command in privileged EXEC
mode. This captures all the OMA DM control and status (CnS) packets.

debug cellular slot/wic_slot/port messages oma-dm

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(22)YB1 This command was introduced.

Usage Guidelines None

Related Commands Command Description

show cellular oma-dm Displays an OMA-DM session details.
cellular cdma activate oma-dm Starts a user initiated OMA-DM session to provision an account
device config and profile update.
cellular cdma activate oma-dm Allows or denies a network initiated alert (NIA) queued in the
ni-alert modem.
cellular cdma activate oma-dm Starts a user initiated OMA-DM session to get an over-the-air PRL
prl-update update.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
68
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular all

show cellular all

To display all the modem information in one listing, use the show cellular all command in privileged
EXEC mode.

show cellular slot/wic_slot/port all

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines The command usage is the same for Global System for Mobile Communications (GSM) and code
division multiple acces (CDMA), although the output is different for each.

Examples This section contains:

• Sample Output for 3G-HWIC-GSM
• Sample Output for 3G-HWIC-CDMA

Sample Output for 3G-HWIC-GSM

The following example shows output from the show cellular all command for slot 0, WIC slot 0, port 0:
router# show cellular 0/0/0 all

Hardware Information
====================
Modem Firmware Version = U1_2_22MCAP G:/WORK
Modem Firmware built = 04/17/06
Hardware Version = E2
International Mobile Subscriber Identity (IMSI) = 001012345678901
International Mobile Equipment Identity (IMEI) = 352678010002779
Factory Serial Number (FSN) = S2128751274E2OK
Modem Status = Online
Current Modem Temperature = 28 deg C, State = Normal

Profile Information
====================
Profile 1 = INACTIVE*
--------

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
69
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular all

PDP Type = IPv4, Header Compression = OFF

Data Compression = OFF
Access Point Name (APN) = vpn.com
Authentication = CHAP
Username: wapuser1, Password: wap

* - Default profile

Data Connection Information

===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 3, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 4, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 5, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 6, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 7, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 8, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 9, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 10, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
router#
Network Information
===================
Current Service Status = No service, Service Error = None
Current Service = Invalid
Packet Service = None
Packet Session Status = Inactive
Current Roaming Status = Home
Network Selection Mode = Automatic
Country = 0, Network =
Mobile Country Code (MCC) = 0
Mobile Network Code (MNC) = 0
Location Area Code (LAC) = 0
Routing Area Code (RAC) = 255
Cell ID = 0
Primary Scrambling Code = 0
PLMN Selection = Automatic

Radio Information
=================
Current Band = None, Channel Number = 0
Current RSSI = -110 dBm

Modem Security Information

==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of Retries remaining = 3
router#

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
70
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular all

Sample Output for 3G-HWIC-CDMA

The following example shows the output from the show cellular all command for slot 0, WIC slot 3,
port 0:
router# show cellular 0/0/0 all

Hardware Information
====================
Modem Firmware Version = p2005600
Modem Firmware built = 11-14-06
Hardware Version = 1.0
Electronic Serial Number (ESN) = 0x6032688F
Preferred Roaming List (PRL) Version = 20224
Current Modem Temperature = 32 degrees Celsius

Profile Information
====================
Electronic Serial Number (ESN) = 0x6032688F
Modem activated = YES

Account Information:
======================
Activation Date: Not available
Phone Number (MDN) : 9135938079
Mobile Station Identifier (MSID) : 9135938079

Data Profile Info:

=====================
Number of data profiles configured : 2
Current active data profile : 1

Data Profile 0 Information

==================================
NAI (Network Access Identifier) = 6032688F@hcm.sprintpcs.com
MN-HA SS = Set
MN-HA SPI = 1234
MN-AAA SS = Set
MN-AAA SPI = 1234
Reverse Tunneling Preference = Set
Home Address = 0.0.0.0
Primary Home Agent Address = 68.28.15.12
Secondary Home Agent Address = 68.28.31.12

Data Profile 1 Information (Active)

==================================
NAI (Network Access Identifier) = productmarketing432@sprintpcs.com
MN-HA SS = Set
MN-HA SPI = 1234
MN-AAA SS = Set
MN-AAA SPI = 1234
Reverse Tunneling Preference = Set
Home Address = 0.0.0.0
Primary Home Agent Address = 68.28.81.76
Secondary Home Agent Address = 68.28.89.76

Data Connection Information

===========================
Phone number of outgoing call =
HDR AT State = Idle, HDR Session State = Open
HDR Session Info:
UATI (Hex) = 0084:0AC0:0000:0000:000A:05DC:A821:DCFC
Color Code = 32, RATI = 0xFFFFFFFF

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
71
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular all

Session duration = 0 msecs, Session start = 0 msecs

Session end = 0 msecs, Authentication Status = Not authenticated
HDR DRC Value = 11, DRC Cover = 0, RRI = Pilot only
Current Transmitted = 0 bytes, Received = 0 bytes
Total Transmitted = 0 KB, Received = 0 KB
Current Call Status = DISCONNECTED
Current Call Duration = 30 secs
Total Call Duration = 4482879 seconds
Current Call State =
Last Call Disconnect Reason = Base station release (No reason)
Last Connection Error = None
HDR DDTM (Data Dedicated Transmission Mode) Preference = Off
Mobile IP Error Code (RFC-2002) = 0 (Registration accepted)

Network Information
===================
Current Service = 1xEV-DO (Rev A) and 1xRTT
Current Roaming Status(1xRTT) = HOME, (HDR) = HOME
Current Idle Digital Mode = HDR
Current System Identifier (SID) = 4183
Current Network Identifier (NID) = 87
Current Call Setup Mode = Mobile IP only
Serving Base Station Longitude = 0 deg 0 min 0 sec
Serving Base Station Latitude = 0 deg 0 min 0 sec
Current System Time = Tue Feb 6 15:12:18 2007

Radio Information
=================
1xRTT related info
------------------
Current RSSI = -94 dBm, ECIO = -8 dBm
Current Channel Number = 50
Current Channel State = Acquired
Current Band Class = Band Class 1

HDR (1xEVDO) related info

-------------------------
Current RSSI = -83 dBm, ECIO = -0 dBm
Current Channel Number = 25
Current Band Class = Band Class 1
Sector ID (Hex) = 0084:0AC0:0000:0000:000A:05DC:A801:1202
Subnet Mask = 104, Color Code = 32, PN Offset = 240
Rx gain control(Main) = 0 dBm, Diversity = Unavailable
Tx total power = -2 dBm, Tx gain adjust = 1536 dBm
Carrier to interference (C/I) ratio = 7

Modem Security Information

==========================
Modem PIN Security UNLOCKED
Power-up lock DISABLED
router#

Related Commands Command Description

cellular cdma activate otasp Activates a cellular account using the over the air service
provisioning (OTASP).
show cellular hardware Displays the cellular modem hardware information.
show cellular network Displays the cellular network (base station) information.
show cellular profile Displays the cellular profile information.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
72
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular all

Command Description
show cellular radio Displays the cellular modem radio statistics.
show cellular security Displays the modem lock state.
show controllers cellular Displays the SMS messages received by the cellular modem.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
73
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular connection

show cellular connection

To display the current active connection state and data statistics, use the show cellular connection
command in privileged EXEC mode.

show cellular slot/wic_slot/port connection

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.
15.1(1)T This command was integrated into Cisco IOS Release 15.1(1)T.

Usage Guidelines The command usage is the same for Global System for Mobile Communications (GSM) and code
division multiple acces (CDMA), although the output is different for each.

Examples This section contains:

• Sample Output for 3G-HWIC-GSM
• Sample Output for 3G-HWIC-CDMA

Sample Output for 3G-HWIC-GSM

The following is sample output for slot 1, wic 0, port 1.
router# show cellular 1/0/1 connection
Data Transmitted = 1066807500 bytes, Received = 1066807500 bytes
Profile 1, Packet Session Status = ACTIVE
IP address = 1.5.97.2
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state

Table 12 describes each output field.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
74
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular connection

Table 12 Output Description

Field Description
Data Transmitted Total data transmitted by the modem. Can be
cleared by the clear counters command.
Data Received Total data received by the modem. Can be cleared
by the clear counters command.
Profile <profile number> Indicates the profiles configured in the modem. A
total of 16 profiles can be configured.
Packet Session Status Packet Data Protocol (PDP) session status of the
profile. Active when the call is made and PDP
context has become active in the modem.
IP Address IP address of the cellular interface received during
IPCP negotiation.
Inactivity Reason Reason why the profile is inactive.

Sample Output for 3G-HWIC-CDMA

The following example is sample output for slot 0, WIC slot 0, port 0 from the show cellular connection
command:
router# show cellular 0/0/0 connection

Phone number of outgoing call =

HDR AT State = Idle, HDR Session State = Open
HDR Session Info:
UATI (Hex) = 0084:0AC0:0000:0000:000A:05DC:A821:DCFC
Color Code = 32, RATI = 0xFFFFFFFF
Session duration = 0 msecs, Session start = 0 msecs
Session end = 0 msecs, Authentication Status = Not authenticated
HDR DRC Value = 11, DRC Cover = 0, RRI = Pilot only
Current Transmitted = 0 bytes, Received = 0 bytes
Total Transmitted = 0 KB, Received = 0 KB
Current Call Status = DISCONNECTED
Current Call Duration = 30 secs
Total Call Duration = 4482879 seconds
Current Call State =
Last Call Disconnect Reason = Base station release (No reason)
Last Connection Error = None
HDR DDTM (Data Dedicated Transmission Mode) Preference = Off
Mobile IP Error Code (RFC-2002) = 0 (Registration accepted)
router#

Table 13 describes each output field.

Table 13 Description of Sample Output for CDMA

Field Description
Phone number of outgoing call Shows the phone number of the data call dialed.
HDR AT State Indicates the AT state. Will show as
CONNECTED when the CONNECT is received
from the modem while dialing out. This is valid
only for 1xEVDO.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
75
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular connection

Table 13 Description of Sample Output for CDMA (continued)

Field Description
HDR Session State Will indicate as OPEN once the HDR session is
established. This is valid only for 1xEVDO
UATI Unicast Access Terminal Identifier (UATI)
obtained by the modem or access terminal (AT)
from the base station during session
establishment.
Color Code HDR session color code for the sector.
RATI HDR Random Access Terminal Identifier used for
opening a session.
Session Duration HDR session duration in milliseconds.
Session Start Phone uptime in units of milliseconds at session
start.
Session End Phone uptime in units of milliseconds at session
end.
Authentication Status Modem or access terminal authentication status
with the base station.
HDR DRC Value The data rate channel value specified by the
access terminal. The access terminal uses DRC
value to specify the requested transmission rate
DRC Cover DRC cover value used by the access terminal to
specify the transmitting sector.
RRI Indicates the rate of the reverse traffic data
channel.
Current Transmitted Number of bytes transmitted by the modem to the
base station. This will be cleared when the call is
disconnected.
Current Received Number of bytes received by the modem from the
base station. This will be cleared when the call is
disconnected.
Current call status Current call status of the modem, such as
CONNECTED, DISCONNECTED, DORMANT,
CONNECTING, or ERROR.
Privacy Mode Current privacy status of the call in progress.
Service Option Service option for the call in progress.
Current Call Duration Duration of the call in progress. A call status of
DISCONNECTED displays the call duration of
the last call.
Total Transmitted Total number of kilobytes transmitted from the
modem. This will be cleared by the clear
counters command.
Total Received Total number of kilobytes received by the modem.
This will be cleared by the clear counters
command.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
76
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular connection

Table 13 Description of Sample Output for CDMA (continued)

Field Description
Total Call Duration Total duration of calls made from the modem.
This will be updated when the current call in
progress is disconnected.
Current Call State Indicates the type of call made.
Last Call Disconnect Reason Indicates why the last call was disconnected.
Last Connection Error Indicates the error code if the call status indicates
an error.
Mobile IP Error Code Indicates the error code in accordance with
RFC-2002 if the call is a mobile IP call.

Note The current call setup mode is in Simple

IP only. In this case show cellular
connection will not display Mobile IP
Error Code. Mobile IP error code is
displayed when call setup mode is either
“Mobile IP only” mode or “Mobile IP
Preferred with SIP fallback” mode.

Related Commands Command Description

cellular cdma activate manual Manually activates a cellular account using the over-the-air service
(OTA) procedure.
show cellular hardware Displays the cellular modem hardware information.
show cellular network Displays the cellular network (base station) information.
show cellular profile Displays the cellular profile information.
show cellular radio Displays the cellular modem radio statistics.
show cellular security Displays the modem lock state.
show controllers cellular Displays HWIC hardware- and driver-specific information.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
77
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular connection personality

show cellular connection personality

To display the negotiated personalities when the 1xEVDO-Rev A service is acquired by the modem, use
the show cellular connection personality command in EXEC mode.

show cellular slot/wic_slot/port connection personality

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default There is no default for this command.

Command Modes EXEC

Command History Release Modification

This command was introduced.

Usage Guidelines None

Examples The following example shows output for code division multiple access (CDMA) for slot 0, WIC slot 0,
port 0:
c2800#show cellular 0/0/0 connection personality
No Active Personalities Negotiated
c2800#

Related Commands Command Description

cellular cdma activate iota Activates a cellular account unsing the internet over the air service
(OTA) procedure.
cellular cdma activate manual Manually activates a cellular account unsing the over the air service
(OTA) procedure or over the air service provisioning (OTASP).
cellular cdma activate otasp Activates a cellular account unsing the over the air service (OTA)
procedure or over the air service provisioning (OTASP).
debug cellular messages all Displays the cellular modem hardware information.
debug cellular messages data Displays the cellular network (base station) information.
debug cellular messages Displays the cellular profile information.
management
show cellular radio Displays the cellular modem radio statistics.
show cellular security Displays the modem lock state.
show controllers cellular Displays the SMS messages received by the cellular modem.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
78
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular connection personality

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
79
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular hardware

show cellular hardware

To display the cellular modem hardware information, use the show cellular hardware command in
privileged EXEC mode.

show cellular slot/wic_slot/port hardware

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines The command usage is the same for Global System for Mobile Communications (GSM) and code
division multiple acces (CDMA), although the output is different for each.

Examples This section contains:

• Sample Output for HWIC-3G-GSM
• Sample Output for HWIC-3G-CDMA

Sample Output for HWIC-3G-GSM

The following example shows output for slot 0, WIC slot 0, port 0:
router# show cellular 0/0/0 hardware

Modem Firmware Version = H1_0_0_1MCAP C:/WS/

Modem Firmware built = 09/08/06
Hardware Version = 1.0
International Mobile Subscriber Identity (IMSI) = <number>
International Mobile Equipment Identity (IMEI) = <number>
Factory Serial Number (FSN) = X2819460254100D
Modem Status = Online
Current Modem Temperature = 33 deg C, State = Normal

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
80
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular hardware

Table 14 Output Description for show cellular hardware command

Field Description
Modem Firmware Version Firmware version of the modem.
Modem Firmware Built Date firmware was built in mm-dd-yy format.
Hardware Version Modem hardware version.
International Mobile Subscriber Identity (IMSI) IMSI is stored in the SIM. IMSI consists of MCC
(mobile country code, 3 digits), MNC (mobile
network code, 3 digits for N. America and 2 digits
for rest of the world) and MSIN (mobile station
identification number). The MCC and MNC in the
IMSI identify the subscribers in the PLMN
(Public Land Mobile Network).
International Mobile Equipment Identity (IMEI) Number that uniquely identifies the modem in a
GSM/UMTS network.
Factory Serial Number (FSN) Unique serial number of the modem.
Modem Status Will be online if the modem has booted up
correctly; otherwise will be offline and the
modem will not be usable.
Current Modem Temperature Radio temperature of the modem in degrees
Celsius. State is normal when temperature is
between 5 to 185°F (-15° to 85°C). If state reaches
critical 226.4°F (108°C), the modem will be
shutdown.

Sample Output for HWIC-3G-CDMA

The following example shows output for slot 0, WIC slot 0, port 0:
router# show cellular 0/0/0 hardware

Modem Firmware Version = p2005600

Modem Firmware built = 11-14-06
Hardware Version = 1.0
Electronic Serial Number (ESN) = 0x6032688F
Preferred Roaming List (PRL) Version = 20224
Current Modem Temperature = 32 degrees Celsiuss

Table 15 describes each output field.

Table 15 Output Description for show cellular hardware command

Field Description
Modem Firmware Version Firmware version of the modem.
Modem Firmware Built Date firmware was built in mm-dd-yy format.
Hardware Version Modem hardware version.
Electronic Serial Number Unique serial number of the modem.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
81
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular hardware

Table 15 Output Description for show cellular hardware command (continued)

Field Description
Preferred Roaming List (PRL) Version PRL version is unique to a service provider. This
indicates to the modem which channels the
modem should scan.
Current Modem Temperature Radio temperature of the modem in degrees
Celsius.

Related Commands Command Description

show cellular radio Displays the cellular modem radio statistics.
show cellular security Displays the modem lock state.
show controllers cellular Displays HWIC hardware- and driver-specific information.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
82
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular network

show cellular network

To display information about the carrier network and service, use the show cellular network command
in privileged EXEC mode.

show cellular slot/wic_slot/port network

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines The command usage is the same for Global System for Mobile Communications (GSM) and code
division multiple acces (CDMA), although the outputs differ.

Examples This section contains:

• Sample Output for HWIC-3G-GSM
• Sample Output for HWIC-3G-CDMA

Sample Output for HWIC-3G-GSM

The following example shows output for HWIC-3G-GSM in slot 0, WIC slot 0, port 0:
router# show cellular 0/0/0 network
Current Service Status = Normal, Service Error = None
Current Service = Combined
Packet Service = UMTS/WCDMA (Attached)
Packet Session Status = Inactive
Current Roaming Status = Roaming
Network Selection Mode = Automatic
Country = USA, Network = CINGULAR
Mobile Country Code (MCC) = 310
Mobile Network Code (MNC) = 380
Location Area Code (LAC) = 56997
Routing Area Code (RAC) = 253
Cell ID = 4503
Primary Scrambling Code = 169
PLMN Selection = Automatic
Registered PLMN = Cingular , Abbreviated =
Service Provider =

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
83
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular network

Table 16 describes each output field.

Table 16 Output Description for show cellular hardware command for GSM

Field Description
Current Service Status Indicates whether service is available.
Current Service Error Shows the error in case there is no service
Current Idle Digital Mode Idle mode of the modem.
Packet Service Indicates the type of service available. For normal
operation, the modem should be attached.
Packet Session Status Status of PDP session. When data transfer is
taking place, packet session will be active.
Current Roaming Status Indicates whether the modem is in the home
network or is roaming.
Network Selection Mode Can be manual selection mode or automatic
selection mode. Set to automatic by default.
Country Country string given by the base station.
Network Network string given by the base station.
Mobile Country Code Country code given by the base station. The
modem will be in the home network only if the
country code given by the base station matches
the MCC of the IMSI and the network code given
by the base station matches the MNC of the IMSI.
Mobile Network Code Network code given by the base station. The
modem will be in the home network only if the
country code given by the base station matches
the MCC of the IMSI and the network code given
by the base station matches the MNC of the IMSI.
Location Area Code LAC given by the base station.
Routing Area Code RAC given by the base station.
Cell ID Cell ID given by the base station.
PLMN Selection Default is automatic.

Sample Output for HWIC-3G-CDMA

The following example shows output for slot 0, WIC slot 0, port 0:
router# show cellular 0/0/0 network

Current Service = 1xEV-DO (Rev A) and 1xRTT

Current Roaming Status(1xRTT) = HOME, (HDR) = HOME
Current Idle Digital Mode = HDR
Current System Identifier (SID) = 4183
Current Network Identifier (NID) = 87
Current Call Setup Mode = Mobile IP only
Serving Base Station Longitude = 0 deg 0 min 0 sec
Serving Base Station Latitude = 0 deg 0 min 0 sec
Current System Time = Tue Feb 6 15:16:9 2007

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
84
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular network

Table 17 Output Description for show cellular hardware command for CDMA

Field Description
Current Service Service attached by the modem.
Current Roaming Status Indicates whether the modem is in the home
network or roaming.
Current Idle Digital Mode Idle mode of the modem.
Current System Identifier SID received by the modem (applicable only for
1xRTT).
Current Network Identifier NID received by the modem (applicable only for
1xRTT).
Current BSS Longitude/Latitude Geographic location of the BSS (if this
information is received from the BSS).
Current System Time System time received from the base station.

Related Commands Command Description

show cellular radio Displays the cellular modem radio statistics.
show cellular security Displays the modem lock state.
show controllers cellular Displays HWIC hardware and driver-specific information.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
85
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular oma-dm

show cellular oma-dm

To display an OMA-DM session details, use the show cellular oma-dm command in privileged EXEC
mode.

show cellular slot/wic_slot/port oma-dm

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(22)YB1 This command was introduced.

Usage Guidelines None

Examples This section contains sample output for show cellular slot/wic_slot/port oma-dm command:

Sample Output for HWIC-3G-CDMA

The following example shows output for HWIC-3G-CDMA for slot 0, WIC slot 3, port 0:
Router#sh cellular 0/3/0 oma-dm
Configuration info
------------------
DM Support = Enabled
Max DM account = 1, DM account in use = 1
DM account changed = No
Device Configuration:
Client-Initiated = Supported, Enabled
Network-Initiated = Supported, Enabled
PRL Update:
Client-Initiated = Supported, Enabled
Network-Initiated = Supported, Enabled
Firmware Update:
Client-Initiated = Not supported, Disabled
Network-Initiated = Not supported, Disabled
Hands Free Activation:
Device-Initiated = Supported, Enabled
Hands Free Activation attempted = Yes

DM session state info

---------------------
DM session state = Session not active
Last session type = Unspecified

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
86
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular oma-dm

Last session initiator = Unspecified

Last session UI mode = Unspecified
Last session result = Success
Last session updated = No

Network-Initiated alert info

----------------------------
NIA state = No NIA pending
Session type = Unspecified
Standard UI mode = Unspecified
Special UI mode = Unspecified
Router#

Related Commands Command Description

cellular cdma activate oma-dm Starts a user initiated OMA-DM session to provision an account
device config and profile update.
cellular cdma activate oma-dm Allows or denies a network initiated alert (NIA) queued in the
ni-alert modem.
cellular cdma activate oma-dm Starts a user initiated OMA-DM session to get an over-the-air PRL
prl-update update.
debug cellular messages Starts OMA-DM debugging.
oma-dm

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
87
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular profile

show cellular profile

To display the cellular profile information, use the show cellular profile command in privileged EXEC
mode.

show cellular slot/wic_slot/port profile <profile number> | all

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.
profile number Profile number for the profile to be displayed.
all Displays information of all profiles in the modem. The maximum number
of supported profiles is 6.

Note In case of HWIC-3G-CDMA-V, only one profile is supported, so

only one profile is displayed.

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.
12.4(22)YB1 This command was modified to display all profiles in the modem.

Usage Guidelines The command usage is the same for Global System for Mobile Communications (GSM) and code
division multiple acces (CDMA), although the output is different for each.

Examples This section contains:

• Sample Output for HWIC-3G-GSM
• Sample Output for HWIC-3G-CDMA

Sample Output for HWIC-3G-GSM

The following example shows output for HWIC-3G-GSM for slot 0, WIC slot 1, port 1:
router# show cellular 0/1/1 profile

Profile 1 = ACTIVE
--------
PDP Type = IPv4, Header Compression = ON
Data Compression = ON

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
88
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular profile

PDP address = 0x7F000201

Access Point Name (APN) = enzo.cisco.com
Authentication = CHAP
Username: cisco, Password: lab
Primary DNS address = 127.0.2.1
Source Address = 127.0.2.1 255.255.255.0

Profile 2 = INACTIVE
---------
PDP Type = IPv4, Header Compression = ON
Data Compression = ON
PDP address = 0x7F000202
Access Point Name (APN) = enzo.cingular.com
Authentication = CHAP
Username: cisco, Password: lab
Primary DNS address = 127.0.2.1
Source Address = 127.0.2.2 255.255.255.0

Table 18 Field Descriptions for show cellular profile command

Field Description
Profile <number> Shows whether a particular profile is ACTIVE or
INACTIVE. The profile is ACTIVE when the
PDP context is active. This happens when a data
call is successfully established.
PDP Type Indicates the packet data protocol (PDP) type.
Supported type is IPv4.
PDP Address Shows the IP address assigned for the PDP
context during PPP negotiation.
Access Point Name Access Point Name for the profile. This
information is provided by the service provider.
Authentication PPP authentication supported. CHAP and PAP are
supported. The type of authentication to be used is
provided by the service provider.
Username Username to be used for PPP authentication. This
information is provided by the service provider.
Password Password to be used for PPP authentication. This
information is provided by the service provider.

Sample Output for HWIC-3G-CDMA

The following example shows output for HWIC-3G-CDMA for slot 0, WIC slot 1, port 1:
router# show cellular 0/0/0 profile

Electronic Serial Number (ESN) = 0x6032688F [09603303567]

Modem activated = YES

Account Information:
======================
Activation Date: Not available
Phone Number (MDN) : 1234567890
Mobile Station Identifier (MSID) : 1234567890

Data Profile Info:

=====================
Number of data profiles configured : 2

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
89
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular profile

Current active data profile : 1

Data Profile 0 Information

==================================
NAI (Network Access Identifier) = 6032688F@hcm.sprintpcs.com
MN-HA SS = Set
MN-HA SPI = 1234
MN-AAA SS = Set
MN-AAA SPI = 1234
Reverse Tunneling Preference = Set
Home Address = 0.0.0.0
Primary Home Agent Address = 68.28.15.12
Secondary Home Agent Address = 68.28.31.12

Data Profile 1 Information (Active)

==================================
NAI (Network Access Identifier) = productmarketing432@sprintpcs.com
MN-HA SS = Set
MN-HA SPI = 1234
MN-AAA SS = Set
MN-AAA SPI = 1234
Reverse Tunneling Preference = Set
Home Address = 0.0.0.0
Primary Home Agent Address = 68.28.81.76
Secondary Home Agent Address = 68.28.89.76

“*” Indicates the default profile.

Table 19 describes the output fields from the command.
Table 19 Field Description

Field Description
Electronic Serial Number A unique serial number for the CDMA modem
displayed in decimal and hexadecimal formats.
Modem Activated Indicates the activation status of the modem. Yes
indicates that the modem is activated on the carrier
network.
Data Profile A data profile consists of the mobile IP (MIP)
settings for the data connection. These settings are
populated on the modem by the network using
OTASP/IOTA.
ProvDate Date the modem was provisioned, in yyyy/mm/dd
format.
MDN Mobile Directory Number assigned to the modem
by the carrier during provisioning.
MIN Mobile Identity Number assigned to the modem
by the carrier during provisioning

Related Commands Command Description

cellular cdma activate manual Manually activates a cellular account using the over-the-air service
(OTA) procedure.
cellular cdma activate otasp Activates a cellular account using the over the air service
provisioning (OTASP).

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
90
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular profile

Command Description
cellular cdma activate iota Provisions data profile using Internet-based over-the-air
provisioning (IOTA).
Note IOTA is supported only with certain wireless service
providers. Please check with your wireless service
provider.
cellular cdma activate oma-dm Starts a user-initiated OMA-DM session to provision an account.
device config

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
91
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular radio

show cellular radio

To display the cellular modem radio statistics, use the show cellular radio command in user privileged
EXEC mode.

show cellular slot/wic_slot/port radio [history <all | per-hour | per-min | per-sec>]

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.
history Displays the RSSI history.
all Complete RSSI history.
per-hour Per-hour RSSI history.
per-min Per-minute RSSI history.
per-sec Per-second RSSI history.

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines The command usage is the same for Global System for Mobile Communications (GSM) and code
division multiple acces (CDMA), although the output is different for each.

Examples This section contains:

• Sample Output for HWIC-3G-GSM
• Sample Output for HWIC-3G-CDMA

Sample Output for HWIC-3G-GSM

The following example shows output for HWIC-3G-GSM in slot 0, WIC slot 0, port 0:
router# show cellular 0/0/0 radio

Current Band = WCDMA 1900, Channel Number = 9721

Current RSSI(RSCP) = -91 dBm

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
92
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular radio

Table 20 Output Description for show cellular radio command for GSM

Field Description
Current Band GPRS/UMTS band to which the modem is
attached.
Channel Number Channel number to which the modem is attached.
Current RSSI Current radio signal strength on the modem. (-125
dbm indicates no signal.)

Sample Output for HWIC-3G-CDMA

The following example shows output for HWIC-3G-CDMA in slot 0, WIC slot 0, port 0:
router#show cellular 0/0/0 radio
1xRTT related info
------------------
Current RSSI = -95 dBm, ECIO = -6 dBm
Current Channel Number = 50
Current Channel State = Acquired
Current Band Class = Band Class 1

HDR (1xEVDO) related info

-------------------------
Current RSSI = -88 dBm, ECIO = -2 dBm
Current Channel Number = 25
Current Band Class = Band Class 1
Sector ID (Hex) = 0084:0AC0:0000:0000:000A:05DC:A801:1202
Subnet Mask = 104, Color Code = 32, PN Offset = 240
Rx gain control(Main) = 0 dBm, Diversity = Unavailable
Tx total power = -2 dBm, Tx gain adjust = 1536 dBm
Carrier to interference (C/I) ratio = 2

Table 21 Output Description for show cellular radio command for HWIC-3G-CDMA

Field Description
Current RSSI Current radio signal strength in dbm (-125 dbm
indicates no signal).
Current ECIO Current energy per chip (ECIO) in dbm.
Current Channel Number Current channel number to which the modem is
attached to the base station.
Current Channel State Indicates whether the modem is scanning or has
acquired the channel.
Current Band Class Current band class that the modem is attached to.
Sector ID Sector ID of the base station to which the modem
is attached.
Subnet Mask Subnet mask of the sector.
Color Code Color code of the sector.
PN Offset PN offset for the sector.
Rx Gain Control Received gain control for the modem.
Tx Total Power Transmitted power.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
93
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular radio

Related Commands Command Description

show cellular all Displays the consolidated information about the modem.
show controllers cellular Displays HWIC-hardware and driver-specific information.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
94
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular security

show cellular security

To display the SIM status (only for HWIC-3G-GSM) and modem lock state, use the show cellular
security command in privileged EXEC mode.

show cellular slot/wic_slot/port security

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default None

Command Modes Privileged EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines The command usage is the same for Global System for Mobile Communications (GSM) and code
division multiple acces (CDMA), although the output is different for each.

Examples This section contains:

• Sample Output for HWIC-3G-GSM
• Sample Output for HWIC-3G-CDMA

Sample Output for HWIC-3G-GSM

The following example shows output for an HWIC-3G-GSM in slot 0, WIC slot 0, port 0:
router# show cellular 0/0/0 security
Card Holder Verification (CHV1) ENABLED
SIM Status = OK
SIM User Operation Required = CHV1
Number of Retries remaining = 3

Table 22 describes the output from this command:

Table 22 Output Description

Filed Description
Card Holder Verification If enabled, access to the SIM is restricted.
SIM Status Indicates whether the SIM is present or removed
from the SIM socket.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
95
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show cellular security

Table 22 Output Description (continued)

Filed Description
SIM User Operation Required If the SIM is protected (for example, because of
CHV1 enabled), it will indicate the type of user
operation required.
Number of Retries Remaining Indicates the number of attempts remaining in
case the SIM is locked. If the number of retries
becomes zero, the SIM is blocked and becomes
unusable.

Sample Output for HWIC-3G-CDMA

The following example shows output for an HWIC-3G-CDMA in slot 0, WIC slot 0, port 0:
router# show cellular 0/0/0 security
Modem PIN Security UNLOCKED
Power-up lock DISABLED

Table 23 describes the output for this command.

Table 23 Output Description

Field Description
Modem PIN Security If the modem is locked, you cannot make calls
without unlocking.
Power-up Lock Shows whether the modem will be locked on
power-up.

Related Commands Command Description

show cellular all Displays the consolidated information about the modem.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
96
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show controllers cellular

show controllers cellular

To display high-speed WAN interface card (HWIC) hardware and driver-specific information, use the
show controllers cellular command in privilege EXEC mode.

show controllers cellular slot/wic_slot/port

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default There is no default for this command.

Command Modes Privilege EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines Use this command to capture the output for debugging or troubleshooting purposes only.

Related Commands Command Description

show interfaces cellular Displays statistics for the cellular interfaces.
show run interface cellular Displays the current running configuration for the cellular
interface.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
97
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show interfaces cellular

show interfaces cellular

To display statistics for the cellular interface, use the show interfaces cellular command in EXEC mode.

show interfaces cellular slot/wic_slot/port

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default There is no default for this command.

Command Modes EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Usage Guidelines When you enter this command, encapsulation should be PPP and all signals, such as DCD, DSR, DTR,
RTS, and CTS, should be up during normal operation.

Examples This section contains:

• Sample Output for 3G-HWIC-GSM
• Sample Output for 3G-HWIC-CDMA

Sample Output for HWIC-3G-GSM

The following example shows the cellular interface statistics for HWIC-3G-GSM in slot 0, WIC slot 0,
port 0 for GSM:
router#

router# show interfaces cellular 0/0/0

Cellular0/0/0 is up, line protocol is up
Hardware is HSDPA/UMTS/EDGE/GPRS-850/900/1800/1900/2100MHz
Internet address is 1.5.97.2/32
MTU 1500 bytes, BW 384 Kbit, RxBW 2400000 Kbit, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP Open
Open: IPCP, loopback not set
Keepalive not set
Time to interface disconnect: idle 3w3d
Last input 00:20:21, output 00:20:21, output hang never
Last clearing of "show interface" counters 00:00:01
Input queue: 1/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
98
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show interfaces cellular

Conversations 0/16/16 (active/max active/max total)

Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 288 kilobits/sec
30 second input rate 0 bits/sec, 0 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 b
*Feb 7 22:55:33.985: %CLEAR-5-COUNTERS: Clear counter on all interfaces by
consoleroadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

Sample Output for HWIC-3G-CDMA

The following example shows the output for an HWIC-3G-CDMA in slot 0, WIC slot 0, port 0 for the
show interfaces cellular command.

router# show int cellular 0/0/0

Cellular0/0/0 is up (spoofing), line protocol is up (spoofing)
Hardware is EVDO Rev A/Rel 0/1xRTT-800/1900MHz / SP
Internet address will be negotiated using IPCP
MTU 1500 bytes, BW 9 Kbit, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP Closed, loopback not set
Keepalive not set
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 6 kilobits/sec
30 second input rate 0 bits/sec, 0 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

Related Commands Command Description

show cellular radio Displays the cellular modem radio statistics.
show controllers cellular Displays HWIC hardware and driver-specific information.
show run interface cellular Displays the current running configuration for the cellular
interface.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
99
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show run interface cellular

show run interface cellular

To see the current running configuration for the cellular interface, use the show run interface cellular
command in privileged EXEC mode.

show run interface cellular slot/wic_slot/port

Syntax Description slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.

Command Default There is no default for this command.

Command Modes Privileged EXEC

Command History Release Modification

12.4(11)XV This command was introduced.
12.4(15)T This command was integrated into Cisco IOS Release 12.4(15)T.

Examples The following example shows the output of the command for 3G HWIC in slot 0, WIC slot 0, port 0:
router#show running-config interface cellular 0/0/0
interface Cellular0/0/0
ip address negotiated
ip access-group 10 out
ip nat outside
ip virtual-reassembly
encapsulation ppp
no ip mroute-cache
load-interval 30
dialer in-band
dialer idle-timeout 2147483
dialer string cdma
dialer-group 2
async mode interactive
no peer default ip address
fair-queue
ppp ipcp dns request
routing dynamic
end router#

Related Commands Command Description

show controllers cellular Displays HWIC hardware and driver-specific information.
show interfaces cellular Displays statistics for the cellular interfaces.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
100
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
show run interface cellular

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
101
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Troubleshooting Tips

Troubleshooting Tips
If you are encountering issues with the working of the 3G wireless Modular and Fixed Cisco ISRs, this
section will help you troubleshoot and pinpoint the cause of failure.

Verifying Configuration
To verify your configuration and to make sure that your connection is up and running, follow these step:

Step 1 After creating a profile with the create cellular profile command, send a ping from a router or attached
host.
Step 2 If you do not get any response, to find where failure is occurring, run the following debug commands:
• debug chat script
• debug PPP negotiation
• show cellular all
• show interface cellular
• show running-config
• show controllers cellular
Step 3 Save the output from all these commands and contact your system administrator.

Checking Signal Strength

If the RSSI level is very low, for example, less than -110 dBm, it means one of the following:
• Your antenna is not connected
• The antenna is not working properly
• There is no service in your area
If all the above are connected and working as they should, contact your system administrator.

Call Setup Using CHAT Script

The following is a sample output for a call that is set up using CHAT script. It shows a received IP
address from the network and indicates that the call setup is successful and the data path is open:

Debugs enabled:
debug modem
debup chat
debug ppp negotiation
debug ppp event
debup ppp error

router# ping www.yahoo.com

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
102
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Troubleshooting Tips

Translating "www.yahoo.com"...domain server (255.255.255.255)

*Mar 1 23:42:57.398: CHAT0/1/0: Attempting async line dialer script
*Mar 1 23:42:57.398: CHAT0/1/0: Dialing using Modem script: sprint & System script: none
*Mar 1 23:42:57.402: CHAT0/1/0: process started
*Mar 1 23:42:57.402: CHAT0/1/0: Asserting DTR
*Mar 1 23:42:57.402: CHAT0/1/0: Chat script sprint started
*Mar 1 23:42:57.402: CHAT0/1/0: Sending string: atdt#777
*Mar 1 23:42:57.402: CHAT0/1/0: Expecting string: CONNECT
*Mar 1 23:42:58.710: CHAT0/1/0: Completed match for expect: CONNECT
*Mar 1 23:42:58.710: CHAT0/1/0: Chat script sprint finished, status = Success
*Mar 1 23:42:58.878: TTY0/1/0: no timer type 1 to destroy
*Mar 1 23:42:58.878: TTY0/1/0: no timer type 0 to destroy
*Mar 1 23:42:58.878: TTY0/1/0: no timer type 2 to destroy
*Mar 1 23:43:00.878: %LINK-3-UPDOWN: Interface Cellular0/1/0, changed state to up
*Mar 1 23:43:00.878: Ce0/1/0 PPP: Using dialer call direction
*Mar 1 23:43:00.878: Ce0/1/0 PPP: Treating connection as a callout
*Mar 1 23:43:00.878: Ce0/1/0 PPP: Session handle[CD00000E] Session id[5]
*Mar 1 23:43:00.878: Ce0/1/0 PPP: Phase is ESTABLISHING, Active Open
*Mar 1 23:43:00.878: Ce0/1/0 PPP: No remote authentication for call-out
*Mar 1 23:43:00.878: Ce0/1/0 LCP: O CONFREQ [Closed] id 5 len 20
*Mar 1 23:43:00.878: Ce0/1/0 LCP: ACCM 0x000A0000 (0x0206000A0000)
*Mar 1 23:43:00.878: Ce0/1/0 LCP: MagicNumber 0x4597FB75 (0x05064597FB75)
*Mar 1 23:43:00.878: Ce0/1/0 LCP: PFC (0x0702)
*Mar 1 23:43:00.878: Ce0/1/0 LCP: ACFC (0x0802)
*Mar 1 23:43:00.878: Ce0/1/0 LCP: I CONFREQ [REQsent] id 12 len 20
*Mar 1 23:43:00.882: Ce0/1/0 LCP: ACCM 0x00000000 (0x020600000000)
*Mar 1 23:43:00.882: Ce0/1/0 LCP: MagicNumber 0x7F576333 (0x05067F576333)
*Mar 1 23:43:00.882: Ce0/1/0 LCP: PFC (0x0702)
*Mar 1 23:43:00.882: Ce0/1/0 LCP: ACFC (0x0802)
*Mar 1 23:43:00.882: Ce0/1/0 LCP: O CONFACK [REQsent] id 12 len 20
*Mar 1 23:43:00.882: Ce0/1/0 LCP: ACCM 0x00000000 (0x020600000000)
*Mar 1 23:43:00.882: Ce0/1/0 LCP: MagicNumber 0x7F576333 (0x05067F576333)
*Mar 1 23:43:00.882: Ce0/1/0 LCP: PFC (0x0702)
*Mar 1 23:43:00.882: Ce0/1/0 LCP: ACFC (0x0802)
*Mar 1 23:43:00.882: Ce0/1/0 LCP: I CONFACK [ACKsent] id 5 len 20
*Mar 1 23:43:00.882: Ce0/1/0 LCP: ACCM 0x000A0000 (0x0206000A0000)
*Mar 1 23:43:00.882: Ce0/1/0 LCP: MagicNumber 0x4597FB75 (0x05064597FB75)
*Mar 1 23:43:00.882: Ce0/1/0 LCP: PFC (0x0702)
*Mar 1 23:43:00.882: Ce0/1/0 LCP: ACFC (0x0802)
*Mar 1 23:43:00.882: Ce0/1/0 LCP: State is Open
*Mar 1 23:43:00.882: Ce0/1/0 PPP: Phase is FORWARDING, Attempting Forward
*Mar 1 23:43:00.882: Ce0/1/0 PPP: Phase is ESTABLISHING, Finish LCP
*Mar 1 23:43:00.882: Ce0/1/0 PPP: Phase is UP
*Mar 1 23:43:00.882: Ce0/1/0 IPCP: O CONFREQ [Closed] id 1 len 22
*Mar 1 23:43:00.882: Ce0/1/0 IPCP: Address 0.0.0.0 (0x030600000000)
*Mar 1 23:43:00.882: Ce0/1/0 IPCP: PrimaryDNS 0.0.0.0 (0x810600000000)
*Mar 1 23:43:00.882: Ce0/1/0 IPCP: SecondaryDNS 0.0.0.0 (0x830600000000)
*Mar 1 23:43:00.882: Ce0/1/0 PPP: Process pending ncp packets
*Mar 1 23:43:00.882: Ce0/1/0 IPCP: I CONFREQ [REQsent] id 4 len 10
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: Address 68.28.57.69 (0x0306441C3945)
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: O CONFACK [REQsent] id 4 len 10
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: Address 68.28.57.69 (0x0306441C3945)
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: I CONFNAK [ACKsent] id 1 len 22
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: Address 70.12.159.189 (0x0306460C9FBD)
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: PrimaryDNS 68.28.58.11 (0x8106441C3A0B)
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: SecondaryDNS 68.28.50.11 (0x8306441C320B)
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: O CONFREQ [ACKsent] id 2 len 22
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: Address 70.12.159.189 (0x0306460C9FBD)
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: PrimaryDNS 68.28.58.11 (0x8106441C3A0B)
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: SecondaryDNS 68.28.50.11 (0x8306441C320B)
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: I CONFACK [ACKsent] id 2 len 22
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: Address 70.12.159.189 (0x0306460C9FBD)
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: PrimaryDNS 68.28.58.11 (0x8106441C3A0B)

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
103
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Troubleshooting Tips

*Mar 1 23:43:00.886: Ce0/1/0 IPCP: SecondaryDNS 68.28.50.11 (0x8306441C320B)

*Mar 1 23:43:00.886: Ce0/1/0 IPCP: State is Open
*Mar 1 23:43:00.886: Ce0/1/0 IPCP: Install negotiated IP interface address 70.12.159.189
*Mar 1 23:43:00.890: Ce0/1/0 IPCP: Install route to 68.28.57.69
*Mar 1 23:43:00.890: Ce0/1/0 IPCP: Add link info for cef entry 68.28.57.69
*Mar 1 23:43:01.878: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0/1/0,
changed state to up
*Mar 1 23:43:01.890: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel1, changed
state to up (68.28.50.11) [OK]

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 209.131.36.158, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 188/196/204 ms

Modem Troubleshooting Using the Diagnostic Port

The RJ-45 port on the faceplate of the 3G wireless HWIC provides access to the debug port on the Sierra
Wireless modem. By connecting an industry-standard diagnostic tool, such as Qualcomm CAIT/QXDM
or Spirent UDM to this port, you can perform radio-level diagnostics and traffic monitoring on the
modem. Use the following test command to turn diagnostics on:
router# test cell-hwic slot/port/wic dm-port on
The cable used to connect the PC/Laptop running the diagnostic tool is the standard Cisco router console
cable (RJ-45 to DB-9).

Note To enable test commands, you must enter the service internal command in the global configuration
mode.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
104
Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Troubleshooting Tips

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and
figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and
coincidental

CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence,
Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are
service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP,
CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo,
Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive,
HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace,
MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare,
SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo
are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (0812R)

© 2010 Cisco Systems, Inc. All rights reserved.

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
105
 Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA,
Troubleshooting Tips

Configuring 3G Wireless for Modular and Fixed Cisco Integrated Services Routers (HWIC-3G-CDMA and HWIC-3G-CDMA-x)
106