RRU3953/RRU3953w Technical
Specifications
Contents
4.1.1.6.4.43 RRU3953/RRU3953w Technical Specifications
4.1.1.6.4.43 RRU3953/RRU3953w Technical
Specifications
An RRU3953/RRU3953w is a multimode radio remote unit. Adopting the
software-defined radio (SDR) technology, RRU3953/RRU3953w modules can work
in different modes with different configurations.
Supported Modes and Frequency Bands
The following table lists the modes and frequency bands supported by an
RRU3953/RRU3953w.
Table 1 Modes and frequency bands supported by an RRU3953/RRU3953w
Type Frequency Receive Transmit Mode IBW (MHz)
Band (MHz) Frequency Frequency
Band (MHz) Band (MHz)
RRU3953w 1800 1710 to 1785 1805 to 1880 GSM, LTE FDD, 75
GL
RRU3953 900 EGSM 880 to 915 925 to 960 GSM, UMTS, GU 35
1800 1710 to 1785 1805 to 1880 GSM, LTE FDD, 45
GL
1900 1850 to 1910 1930 to 1990 GSM, UMTS, 40
LTE FDD, GU,
GL, UL, GUL
Table 1 Modes and frequency bands supported by an RRU3953/RRU3953w
Type Frequency Receive Transmit Mode IBW (MHz)
Band (MHz) Frequency Frequency
Band (MHz) Band (MHz)
2100 1920 to 1980 2110 to 2170 UMTS, LTE 60
FDD, UL
RF Specifications
Table 2 lists radio frequency (RF) specifications of an RRU3953/RRU3953w.
NOTE:
ATBR in the Transmit and Receive Channels column indicates that this RF module has A
transmit channels and B receive channels.
CxD W in the Output Power column indicates that this RF module is configured with C
transmit channels and the maximum output power of each transmit channel is D W.
EF MSR indicates that E and F data is carried on the same transmit channel of an RF
module.
EF non-MSR indicates that E and F data is carried on two different transmit channels of
an RF module.
GSM receiver sensitivity is measured, as recommended in 3GPP TS 51.021, at the antenna
connector on condition that the channel rate reaches 13 kbit/s and the bit error rate
(BER) is not higher than 2%.
UMTS receiver sensitivity is measured, as recommended in 3GPP TS 25.104, at the antenna
connector on condition that the channel rate reaches 12.2 kbit/s and the BER is not
higher than 0.001.
LTE FDD receiver sensitivity is measured, as recommended in 3GPP TS 36.104, under a 5
MHz channel bandwidth based on the FRC A1-3 in Annex A.1 (QPSK, R = 1/3, 25 RBs)
standard.
The RRU3953/RRU3953w that works in GSM mode and operates in the 1800 MHz frequency band
complies with the EN 301 502 V9.2.1 standard. The RRU3953/RRU3953w that works in GSM
mode and operates in the 1900 MHz frequency band complies with the 3GPP TS 45.005
V10.2.0 and 3GPP TS 51.021 V10.2.0 standards.
The RRU3953/RRU3953w that works in UMTS, LTE FDD, or MSR mode and operates in the 1800
MHz or 2100 MHz frequency band complies with the ETSI EN 301 908 V5.2.1 and 3GPP TS
37.104 standards. The RRU3953/RRU3953w that works in UMTS, LTE FDD, or MSR mode and
operates in the 1900 MHz frequency band complies with the 3GPP TS 37.104 V10.4.0 and
3GPP TS 37.141 V10.4.0 standards.
Table 2 RF specifications of an RRU3953/RRU3953w
Type Transmit Capacity Receiver Sensitivity (dBm) Output Pow
and
Receive Receiver Receiver Receiver
Channels Sensitivity Sensitivity Sensitivity with
with One with Two Four Antennas
Antenna Antennas
RRU3953/RRU3953w 2T4R GSM: 8 TRXs GSM: GSM: GSM: The
UMTS: 900 900 900 MHz RRU3953/RRU39
Without MIMO: 6 MHz MHz EGSM: -119.3 supports a
carriers EGSM: EGSM: (theoretical maximum power
-113.8 -116.6 value) configuration
With MIMO: 4 2x80 W. When
carriers 1800 1800 1800 MHz: -
working in GS
MHz: - MHz: - 119.5
LTE FDD: mode, it supp
114.0 116.8 (theoretical
1800 MHz/1900 a maximum pow
1900 1900 value)
MHz: 2 carriers. configuration
MHz: - MHz: - 1900 MHz: - 2x60 W.
The bandwidth
113.7 116.5 119.2
per carrier is For typical p
(theoretical
1.4/3/5/10/15/20 UMTS: UMTS: configuration
value)
MHz. 900 900 see Typical Pow
MHz MHz UMTS: Configuration for
EGSM: EGSM: 900 MHz RRU3953/RRU39
-125.9 -128.7 EGSM: -131.4
1900 1900 1900 MHz: -
MHz: - MHz: - 131.3
125.8 128.6 2100 MHz: -
2100 2100 131.3
MHz: - MHz: - LTE FDD:
125.8 128.6
1800 MHz: -
LTE FDD: LTE FDD: 112.1
1800 1800 1900 MHz: -
MHz: - MHz: - 111.8
106.6 109.4 2100 MHz: -
1900 1900 112.0
MHz: - MHz: -
106.3 109.1
2100 2100
MHz: - MHz: -
106.5 109.3
Engineering Specifications
The following table lists the equipment specifications of an
RRU3953/RRU3953w.
Table 3 Equipment specifications of an RRU3953/RRU3953w
Type Input Power Dimensions (H x W x D) Weight (kg)
RRU3953/RRU3953w -48 V DC; voltage 400 mm x 300 mm x 20 (without the
range: -36 V DC to - 150 mm (without the housing)
57 V DC housing)
NOTE:
The RRU3953/RRU3953w
supports AC power supply
when connected to an
external AC/DC power
module or an OPM15M.
For details, see AC/DC
Power Module User Guide
and OPM15M User Guide.
The following table lists the environmental specifications of an
RRU3953/RRU3953w.
Table 4 Environmental specifications of an RRU3953/RRU3953w
Type Operating Relative Absolute Atmospheric
Temperature Humidity Humidity Pressure
3
RRU3953/RRU3953w Without 5% RH to 100% 1 g/m to 30 70 kPa to 106
solar RH g/m3 kPa
radiation: -
40°C to
+55°C
With solar
radiation: -
40°C to
+50°C
NOTE:
According to the
installation scenario,
traffic load, and
carrier
configuration, the
output power of
some RRUs may
temporarily
Table 4 Environmental specifications of an RRU3953/RRU3953w
Type Operating Relative Absolute Atmospheric
Temperature Humidity Humidity Pressure
decrease when they
work in the highest
10°C temperature
range. For example,
if the highest
operating
temperature allowed
for an RRU is 50°C,
the actual operating
temperature cannot
exceed 40°C.
Otherwise, the
output power of the
RRU may
temporarily
decrease.
The following table lists the compliance standards for an RRU3953/RRU3953w.
Table 5 Compliance standards for an RRU3953/RRU3953w
Item Standard
RF 3GPP TS 45.005
3GPP TS 25.141
3GPP TS 36.141
3GPP TS 37.141
Operating environment ETSI EN 300019-1-4 V2.1.2 (2003-04) Class 4.1: "Non-
weatherprotected locations"
Storage environment ETSI EN300019-1-1 V2.1.4 (2003-04) class1.2
"Weatherprotected, not temperature-controlled storage
locations"
NOTE:
The validity period is one year.
The product can function properly within the validity period if the
storage environment meets the preceding standards.
Shockproof protection NEBS GR63 zone4
Table 5 Compliance standards for an RRU3953/RRU3953w
Item Standard
Ingress Protection (IP) IP65
rating
Surge protection IEC 62305-1 Protection against lightning - Part
1:General principles
IEC 62305-3 Protection against lightning - Part
3:Physical damage to structures and life hazard
IEC 62305-4 Protection against lightning - Part
4:Electrical and electronic systems within
structures
ITU-T K.35 Bonding configurations and earthing at
remote electronic sites
ITU-T K.56 Protection of radio base stations
against lightning discharges
ITU-T K.97 Lightning protection of distributed base
stations
ETSI EN 300 253 Environmental
Engineering(EE):Earthing and bonding configuration
inside telecommunications centers
YD 2324-2011 Lightning protection requirements and
test methods for Radio Base Stations (RBSs)
GB/T 50689-2011 Code for design of lightning
protection and earthing engineering for
telecommunication bureaus (stations)
lists the surge protection specifications of ports on an
Table 6
RRU3953/RRU3953w.
NOTE:
Unless otherwise specified, the surge protection specifications depend on the surge
waveform of 8/20 μs.
All the surge current items, unless otherwise specified as Maximum discharge current,
refer to Nominal discharge current.
Table 6 Surge protection specifications of ports on an RRU3953/RRU3953w
Port Surge Protection Surge Protection Specifications
Mode
Power port Surge current 20 kA
Specifications of CPRI Ports
The following table lists the specifications of CPRI ports on an
RRU3953/RRU3953w.
Table 7 Specifications of CPRI ports on an RRU3953/RRU3953w
Type Quantity CPRI Port Rate Topology Cascading Maximum
of CPRI (Gbit/s) Level Distance from the
Ports BBU (km)
RRU3953/RRU3953w 2 1.25/2.5/4.9/9.8 Star, CPRI GU: 40
chain, MUX: GL/UL/GUL:
or dual- GU: 6
The maximum
star
GL: 4 distance from
UL: 4 the BBU
GUL: 4 varies with
the types of
LTE BBPs
configured.
When the
LBBPc,
LBBPd1,
UBBPd3, or
UBBPda is
configured:
20
When the
LBBPd2 or
UBBPd4 is
configured:
40
When the
LBBPd3,
UBBPd5, or
UBBPd6 is
configured
40 if
the cell
number
is less
than or
equal to
3
Table 7 Specifications of CPRI ports on an RRU3953/RRU3953w
Type Quantity CPRI Port Rate Topology Cascading Maximum
of CPRI (Gbit/s) Level Distance from the
Ports BBU (km)
20 if
the cell
number
is
greater
than or
equal to
4
Antenna Capability
The following table lists the antenna capability of an RRU3953/RRU3953w.
Table 8 Antenna capability of an RRU3953/RRU3953w
Type TMA Support RET Antenna Support
RRU3953/RRU3953w Supported AISG2.0 and AISG1.1
NOTE:
For RF modules supporting RET antennas, the feeding voltage is 12 V and feeding current is
2.3 A.
Parent topic: Technical Specifications of RRUs
