Scribd
Upload
1K views2 pages

TMB Tune Up

The document is a checklist in Bahasa Indonesia for inspecting a vehicle. It contains 11 sections to inspect things like the engine oil, ignition system, battery, fuel system, cooling system, and exhaust emissions. Measurements are taken of things like spark plug gaps, compression pressures, voltages, and emission readings before and after adjustments are made. The full inspection and any work performed is documented on a report sheet.

Uploaded by

Surya Irawan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
1K views2 pages

TMB Tune Up

The document is a checklist in Bahasa Indonesia for inspecting a vehicle. It contains 11 sections to inspect things like the engine oil, ignition system, battery, fuel system, cooling system, and exhaust emissions. Measurements are taken of things like spark plug gaps, compression pressures, voltages, and emission readings before and after adjustments are made. The full inspection and any work performed is documented on a report sheet.

Uploaded by

Surya Irawan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

No Item Hasil Pemeriksaan

Bagus Jelek
1. Persiapan:
Kendaraan
Pelindung kendaraan
2. Persiapan
Pengecekan tools dan equipment
Kalibrasi peralatan
3. Penempatan tools dan equipment
Penanganan dan penempatan komponen
4. Lihat buku manual yang tersedia
Spesifikasi tahanan primer coil 1,5-1,9 ohm
Baca wiring harnes sistem pengapian yang berhubungan dengan
ignition coil: a. Kunci kontak b. Distributor
Tentukan letak dan besarnya fuse engine: 10 Amp
5. Oil level
Kualitas oli
Periksa celah (gap) katup dan stel bila diperlukan:
Silinder 1: in 0,2 mm Silinder 1: in 0,3 mm
Silinder 2: in 0,2 mm Silinder 2: in 0,3 mm
Silinder 3: in 0,2 mm Silinder 3: in 0,3 mm
Silinder 4: in 0,2 mm Silinder 4: in 0,3 mm
Tekanan kompresi sil. 1= 80 psi; 2= 70 psi; 3= 70 psi; 4= 70 psi
Gambar alur pengencangan baut kepala silinder.
8 6 1 3 9

10 4 2 5 7
6. Sistem pengapian
a. Celah busi silinder no.1= 0,8 mm kondisi
no.2= 0,7 mm kondisi
no.3= 0,7 mm kondisi
no.4= 0,8 mm kondisi
b. Tahanan kabel busi no.1= 4 k ohm
no.2= 3,5 k ohm
no.3= 3,5 k ohm
no.4= 3,5 k ohm
Kabel coil 150 k ohm
c. Tahanan primer coil 1,5 ohm
Tahana sekunder coil 9 k ohm
d. Kondisi distributor shaft
Kondisi rotor
Kondisi tutup distributor
e. Celah platina (air gap) (signal generator)
f. Kondisi governor advancer
Kondisi vacum advancer
7. Baterai
BJ sel: 1= 1200; 2= 1200; 3= 1200; 4= 1225; 5=1210; 6= 1200
Tegangan 12 volt
Ketinggian air baterai
Kondisi air terminal
Kondisi bodi
8. Sistem bahan bakar
Saringan udara
Saringan bahan bakar dan pipa/selang aliran
9. Sistem pendingin
Kondisi fan belt
Tegangan fan belt
Tekanan/kebocoran radiator, hose dan water pump
Tekenan tutup radiator alat tidak berfungsi
Kondisi recervoir (level air pendingin)
10. Analisa kendaraan
Idling speed 800 rpm
Sudut dwell 50°
Penyetelan campuran bahan bakar
Ignition timing
11. Exhaust emission test (sebelum dan sesudah penyetelan)
Idling speed sebelum sebelum sesudah
CO reading % %
CO2 reading % %
Lamda reading
HC reading ppm ppm
12. Tulis semua pekerjaan yang di reeport sheet

You might also like