BIDDING DOCUMENT

FOR

PLANT BUILDING WORKS

(BIDDING DOCUMENT NO.: RJ/B018-000-CJ-T-8105/1015)

PROJECT: GURU GOBIND SINGH POLYMER ADDITION

PROJECT AT GURU GOBIND SINGH REFINERY OF M/S HMEL
AT BATHINDA

CLIENT: M/S HMEL

PART-II OF III : PRICED PART

 INDEX
PART – II – PRICE PART

SR. NO. DESCRIPTION

1. PREAMBLE TO SCHEDULE OF RATES

2. SUMMARY OF PRICE – FORM SP-0

3. SCHEDULE OF RATES

• FORM SP-1 (Detailed Description)

 PRICE PART
GURU GOBIND SINGH
POLYMER ADDITION
PROJECT
-----------------------------------------------------------------------------------------------------------------------------------------

PREAMBLE
TO
SCHEDULE OF RATES/ PRICES

Page 1 of 2
 PRICE PART
GURU GOBIND SINGH
POLYMER ADDITION
PROJECT
-----------------------------------------------------------------------------------------------------------------------------------------

PREAMBLE TO SCHEDULE OF RATES/ PRICES

1.0 The Schedule of Price shall be read with all other sections of this Bidding Document.
2.0 The CONTRACTOR is deemed to have studied the drawings, specifications and details of
works to be done within the Time Schedule and should have acquainted himself of the
conditions prevailing at site.
3.0 The quantities shown against the various items are only approximate and may vary to any
extent individually subject to conditions given in General Conditions of Contract/Special
Conditions of Contract.
4.0 No claim shall be entertained during currency of this Contract towards any items due to the
above including where the CONTRACTOR has quoted low/ high rates.
5.0 OWNER/EIL reserves the right to interpolate or extrapolate the rates for any new item of work
not covered in Schedule of Price from the similar items already available in schedule of rates.
All the works shall be measured upon completion and paid for at the rate quoted and accepted
in the "Schedule of Price". In case any activity though specifically not covered in schedule of
rates descriptions but the same is covered under scope of work/ scope of supply/ specification/
drawings etc. no extra claim on this account shall be entertained, since Schedule of Price is to
be read in conjunction with all other documents forming part of the Contract.
6.0 All items of work mentioned in the Schedule of Price shall be carried out as per the
specifications, drawings and instructions of OWNER/EIL and the rates are deemed to be
inclusive of material, consumable, labour, supervision, tools & tackles and detailing of
construction/fabrication drawings, isometric wherever required as called for in the detail
specification and conditions of the Contract.
7.0 Pre-filled short SOR with prices is enclosed herewith. Bidders shall quote their prices as
percentage variation on total prices. This percentage variation as quoted by the bidder will
apply to all work items of SOR.
8.0 Bidder shall indicate the increase/decrease on total estimated value/Price in terms of
percentage up-to 2 decimal places in the “Summary of Prices” sheet. Bidder shall not change
rate/amount indicated in ‘Schedule of Rates’.
9.0 Bidder to quote Two year spares etc. as per Technical section separately in separate
annexure.
10.0 OWNER/EIL reserves the right to cancel/ delete/ curtail any item or group of work if
necessary. Such a step shall not be construed as reason for changing the rates.

_____________________________
(STAMP & SIGNATURE OF BIDDER)

Page 2 of 2
 PRICE PART
GURU GOBIND SINGH
POLYMER ADDITION
PROJECT
-----------------------------------------------------------------------------------------------------------------------------------------

FORM- SP-0

(SUMMARY OF PRICES)

Page 1 of 2
 PRICE PART
GURU GOBIND SINGH
POLYMER ADDITION
PROJECT
-----------------------------------------------------------------------------------------------------------------------------------------

FORM SP-0
SUMMARY OF PRICE

BIDDING DOCUMENT NO: RJ/B018-000-CJ-T-8105/1015

NAME OF BIDDER: M/s. ____________________________________________________

PRICE IN INDIAN RUPEES

Sl. No. Description
(INR)

Total Quoted Price for Electrical Works

INR 19,47,54,590 /-
1.
(SOR NO. B018-000-16-50-CJ-SOR-8105-0-0M)

Total Quoted Price for Mechanical Equipment Works INR 36,46,99,800 /-

2.
(SOR NO. B018-000-80-42-CJ-SOR-8105-0-0M)

Total Quoted Price for Civil-Structural and Architectural INR 206,27,90,340 /-

3. Works
(SOR NO. B018-000-81-41-CJ-SOR-8105-0-0M)

Sum Total of all above INR 262,22,44,730/-

4.
(Total of Sl. No. 1 to 3)

Percentage increase/ decrease on Total estimated cost In figure______________%

for total work (i.e. on 4 above), applicable on all items
5. In words __________percent
of SOR
(Refer Note-1)

(In figure) INR ________________

Total amount after considering percentage
6.
Increase/Decrease as above (In Words) INR ________________

Note:
1. Bidder shall indicate the Percentage Increase/Decrease under Sl. No. 5 and amount as per Sl. No. 6 in
Price bid only (and not in techno-commercial bid).
2. Bidder shall indicate (+) for increase and (-) for decrease. For no increase/decrease, ‘NIL’ shall be
indicated.
3. In case “+” or “-” not indicated, then “+” shall be considered. Also in case, bidder left the Row “5” & 6” Blank,
NIL shall be considered for increase/decrease.
4. In case of discrepancy between + percentage indicated against item "5" and total amount against Item "6";
the percentage against item "5" will prevail and amount shall be recalculated.
5. The percentage should be quoted up to 2 decimal places.

(STAMP & SIGNATURE OF BIDDER)

Page 2 of 2
 PRICE PART
GURU GOBIND SINGH
POLYMER ADDITION
PROJECT
-----------------------------------------------------------------------------------------------------------------------------------------

SCHEDULE OF RATES

FORM SP-1 (DETAILED DESCRIPTION)

Page 1 of 1
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SCHEDULE OF RATES

Contractor : .

Bidding Document No. : B018-000-CJ-T-8105/1015

Bidding Document Name : PLANT BUILDINGS

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 1 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-16-50-CJ-SOR- SOR Title Electrical Works Department ENGINEERING-ELECTRICAL

8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

1 EE ELECTRICAL -
2 E104.00.00 MISCELLANEOUS CONTROL GEAR -
3 E104.01.00 Installation, testing and commissioning of miscellaneous surface mounted
industrial/FLP control gear such as lighting/power panel, push button stations, motor
starter, communication equipment, junction boxes, panels, plugs, sockets, including
supply of necessary hardware, touch up painting including supply of paint, including
transportation from store/yard to site at the place of installation, unpacking, (excluding
fixing of cable glands and cable terminations), including all labour and materials, as
per approved drawings, specifications of this tender and directions of Engineer-in-
Charge. -
4 E104.01.01 Weight of the unit up to 5 kg. - NOS 50.00 610.00 Six One Zero 30,500.00
5 E104.02.00 Supply of Industrial, weather proof type Push Button stations as per EIL specification
No. 6-51-0014, as per approved drawings, specifications of this tender and directions
of Engineer-in-Charge. -
6 E104.02.02 With start and stop push buttons. - NOS 50.00 3,870.00 Three Eight Seven Zero 193,500.00
7 E106.00.00 PLUGS, SOCKETS AND JUNCTION BOXES -
8 E106.01.00 Supply of weatherproof metal clad 415V, TPN, industrial type socket and plug with
heavy duty interlocking switch, with adequately sized cable adaptor box for incoming
and outgoing cable terminations, including supply of double compression brass nickel
plated cable glands, tinned copper lugs, including all labours and materials, as per
approved drawings, specifications of this tender and directions of Engineer-in-Charge.
-
9 E106.01.01 63 A, 415 V, 5 pin sockets. - NOS 60.00 15,000.00 One Five Zero Zero Zero 900,000.00
10 E207.00.00 G.I. PIPES -
11 E207.01.00 Supply and laying of following sizes of G.I. Pipes (medium) in required length fixed
on steel, concrete or similar structure, laid in trenches, ready to be buried in concrete
including cutting, threading, bending and similar works, supply of clamps, small iron
structures, spacers and installation of seats, plugs, bushings etc., small civil works,
including all labour and materials, as per approved drawings, specifications of this
tender and directions of Engineer-in-Charge. -
12 E207.01.04 80 mm NB. - M 310.00 1,000.00 One Zero Zero Zero 310,000.00
13 E207.01.05 100 mm NB. - M 200.00 1,750.00 One Seven Five Zero 350,000.00
14 E207.01.07 150 mm NB. - M 480.00 2,620.00 Two Six Two Zero 1,257,600.00
15 E209.00.00 CABLE - TRAYS -
16 E209.03.00 Supply and installation of following galvanised slotted channel trays of 2 mm
thickness and 50 mm high for supporting cables, including all labour and materials, as
per approved drawings, specifications of this tender and directions of Engineer-in-
Charge. -
17 E209.03.01 100 mm wide. - 100 WIDE SLOTTED CHANNEL TRAY M 16000.00 590.00 Five Nine Zero 9,440,000.00

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 2 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-16-50-CJ-SOR- SOR Title Electrical Works Department ENGINEERING-ELECTRICAL

8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

18 E303.00.00 HAZARDOUS AREA LIGHTING FIXTURES AND ACCESSORIES -

19 E303.02.00 Supply of following FLP/Div.2 lighting fixtures complete with lamps, requisite FLP
cable glands, plugs and necessary control gear as per EIL standard specification No.
6-51-0061, data sheet for lighting fixture schedule, including all albour and materials,
specifications of this tender and directions of Engineer-in-Charge. -
20 E303.02.63 Type FLP-LED-12 Fixtures. - GAS GROUP SHALL BE IIC Nos 200.00 27,300.00 Two Seven Three Zero 5,460,000.00
Zero
21 E304.00.00 SAFE AREA LIGHTING FIXTURES -
22 E304.01.00 Supply, installation, testing and commissioning of following lighting fixtures and
connecting to wiring junction box/marshalling box complete with lamps and necessary
control gear including supply of all connected materials like flexible conduit, clamps,
supports, chains, anchor fastners, bolts, nuts and washers etc. as required, including
supply and fixing of cable glands, lugs, including all labour and materials, as per
approved drawings, data sheet for lighting fixture schedule, EIL installation standards,
specifications of this tender and directions of Engineer-in-Charge. -
23 E304.01.54M01 Type ST 12L LED Fixtures. - NOS 900.00 7,180.00 Seven One Eight Zero 6,462,000.00
24 E304.01.62 Type BK 3 Fixtures. - NOS 170.00 1,660.00 One Six Six Zero 282,200.00
25 E304.02.00 Supply, installation, testing and commissioning of following energy efficient lighting
fixtures and connecting to wiring junction box/marshalling box complete with lamps
and necessary control gear including supply of all connected materials like flexible
conduit, clamps, supports, chains, anchor fastners, bolts, nuts and washers etc. as
required, including supply and fixing of cable glands, lugs, including all labour and
materials, as per approved drawings, data sheet for lighting fixture schedule, EIL
installation standards, specifications of this tender and directions of Engineer-in-
Charge. -
26 E304.02.20 Type LED 1 Fixtures. - NOS 600.00 11,500.00 One One Five Zero 6,900,000.00
Zero
27 E304.02.21 Type LED 2 Fixtures. - NOS 6200.00 7,900.00 Seven Nine Zero Zero 48,980,000.00
28 E304.02.24 Type LED 5 Fixtures. - NOS 165.00 4,700.00 Four Seven Zero Zero 775,500.00
29 E304.02.25 Type LED 6 Fixtures. - NOS 40.00 4,700.00 Four Seven Zero Zero 188,000.00
30 E304.02.27 Type LED 8 Fixtures. - NOS 5840.00 1,880.00 One Eight Eight Zero 10,979,200.00
31 E304.02.27M01 Type LED 8A Fixtures. - NOS 70.00 7,000.00 Seven Zero Zero Zero 490,000.00
32 E304.02.27M02 Type LED 8C Fixtures - NOS 110.00 3,000.00 Three Zero Zero Zero 330,000.00
33 E304.02.29 Type LED 10 Fixtures. - NOS 110.00 1,580.00 One Five Eight Zero 173,800.00
34 E304.02.30 Type LED 11 Fixtures. - NOS 20.00 2,300.00 Two Three Zero Zero 46,000.00
35 E304.02.30M01 Type LED 11A Fixtures. - NOS 150.00 2,770.00 Two Seven Seven Zero 415,500.00
36 E304.02.30M02 Type LED 11B Fixtures. - NOS 200.00 3,500.00 Three Five Zero Zero 700,000.00
37 E304.02.34 Type LED 15 Fixtures. - NOS 85.00 19,100.00 One Nine One Zero 1,623,500.00
Zero
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 3 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-16-50-CJ-SOR- SOR Title Electrical Works Department ENGINEERING-ELECTRICAL

8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

38 E304.02.35 Type LED 16 Fixtures. - NOS 100.00 22,740.00 Two Two Seven Four 2,274,000.00
Zero
39 E304.02.37 Type LED 18 Fixtures. - NOS 120.00 20,400.00 Two Zero Four Zero 2,448,000.00
Zero
40 E304.02.38 Type LED 19 Fixtures. - NOS 40.00 5,000.00 Five Zero Zero Zero 200,000.00
41 E305.00.00 FANS AND EXHAUST FANS -
42 E305.01.00 Supply, installation, connection, testing and commissioning of following types of
exhaust fans including supply of all necessary supports etc., including fixing of cable
glands, lugs with BEE(Bureau of Energy Efficiency) rating of minimum 3 star
including all labour and materials and accessories like mounting frame, fixing bolt,
wire guard/louvres etc., as per approved drawings, specifications of this tender and
directions of Engineer-in-Charge. -
43 E305.01.01 300 mm dia., 1 phase, 900 rpm, wall mounting type epoxy painted exhaust fan with NOS 30.00 4,970.00 Four Nine Seven Zero 149,100.00
louvres. -
44 E305.01.06 450 mm dia., 1 phase, 900 rpm, wall mounting type epoxy painted exhaust fan with NOS 50.00 15,750.00 One Five Seven Five 787,500.00
louvres suitable for Gas group IIC, temperature class T3. - Zero
45 E305.04.00 Supply, installation, connection, testing and commissioning of 240 V AC, 1200 mm NOS 90.00 3,310.00 Three Three One Zero 297,900.00
sweep ceiling fan with regulator (labeled as minimum 3-star by Bureau of Energy
Efficiency)including providing clamp/hook in RCC slab, if necessary, providing, fixing,
ceiling, rose, wiring, including all labour and materials, as per approved drawings,
specifications of this tender and directions of Engineer-in-Charge. -
46 E307.00.00 SOCKETS/RECEPTACLES AND SWITCHES/MCB UNITS -
47 E307.01.00 Supply, installation, connection, testing and commissioning of following ratings of 240
V, single phase, sockets/receptacles and metallic outlet boxes as described below
including supply of all connected materials, including all labour and materials, as per
approved drawings, specifications of this tender and directions of Engineer-in-Charge.
-
48 E307.01.02 6 A, 5 pin plate type flush/ surface mounting sockets/receptacles. - NOS 60.00 390.00 Three Nine Zero 23,400.00
49 E307.01.02M02 6 A, 5 pin Flame proof plate type flush/ surface mounting sockets/receptacles. - GAS NOS 55.00 500.00 Five Zero Zero 27,500.00
GROUP SHALL BE IIC
50 E307.01.04 16/6 A, 6 pin plate type flush/ surface mounting sockets/receptacles. - NOS 410.00 610.00 Six One Zero 250,100.00
51 E307.01.04M01 3 Nos. 5/15 A, 240 V Receptacle with 1 No. 15 A Switch for Computers (flush/ surface NOS 340.00 900.00 Nine Zero Zero 306,000.00
mounting sockets/receptacles) -
52 E307.01.06 20 A, 3 pin surface mounted industrial type switch socket with plug and sheet steel NOS 330.00 2,210.00 Two Two One Zero 729,300.00
painted box. -
53 E307.02.00 Supply, installation, connection, testing and commissioning of following 240 V, single
phase switches/MCB units, including outlet boxes and associated accessories,
including all labour and materials, as per approved drawings, specifications of this
tender and directions of Engineer-in-Charge. -
54 E307.02.01 5 A, piano type flush/surface mounted swtches. - NOS 1890.00 390.00 Three Nine Zero 737,100.00
55 E307.02.01M01 Flameproof Type 5 A, piano type flush/surface mounted switches. - NOS 60.00 468.00 Four Six Eight 28,080.00

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 4 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-16-50-CJ-SOR- SOR Title Electrical Works Department ENGINEERING-ELECTRICAL

8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

56 E307.02.03 15 A, piano type flush/surface mounted swtches. - NOS 700.00 560.00 Five Six Zero 392,000.00
57 E307.02.06 32A, DP MCB unit in moulded case enclosure for window / split type air conditioner - NOS 95.00 1,250.00 One Two Five Zero 118,750.00
58 E308.00.00 JUNCTION BOXES (OUTDOOR/INDOOR TYPE) -
59 E308.02.00 Supply and installation of dust and vermin proof G.I. sheet steel (1.6 mm thick)
junction box suitable for indoor installation, complete with 15A, 20 terminals, supply
and fixing of cable glands for incoming cable and knock outs for conduit entry for
outgoing circuits, including all labour and materials, as per approved drawings,
specifications of this tender and directions of Engineer-in-Charge. -
60 E308.02.01 Junction box. - NOS 25.00 3,310.00 Three Three One Zero 82,750.00
61 E309.00.00 LIGHTING/POWER PANELS AND DISTRIBUTION BOARDS -
62 E309.02.00 Supply, installation, connection, testing and commissioning of safe area
lighting/power panels, surface/flush mounting type, wall mounting type in dust tight
(with hinged cover) sheet steel enclosure having 4 pole incomer and single pole MCB
(9 kA type) for outgoing circuit control with complete wiring, including cable
termination, connection and fixing of cable glands, including all labour and materials,
as per approved drawings, specifications of this tender and directions of Engineer-in-
Charge. -
63 E309.02.03 63 A, 4 pole incomer MCB isolator and 18 Nos. outgoing single pole MCBs (upto 20 NOS 41.00 22,050.00 Two Two Zero Five 904,050.00
A). - Zero
64 E309.02.04M01 63 A, 4 pole incomer MCB isolator and ELCB and 6 Nos. outgoing single pole MCBs NOS 50.00 19,500.00 One Nine Five Zero Zero 975,000.00
(upto 20 A). -
65 E309.02.05M01 63 A, 4 pole incomer MCB isolator and ELCB and 12 Nos. outgoing single pole NOS 86.00 20,000.00 Two Zero Zero Zero 1,720,000.00
MCBs (upto 20 A). - Zero
66 E310.00.00 WIRING -
67 E310.03.00 Circuit wiring with 660 V grade, (sizes given below), FRLS PVC insulated copper
wires in already laid surface/concealed conduit from lighting panel/power panel
onwards including the supply of wires, termination and connection, including all labour
and materials, as per approved drawings, specifications of this tender and directions
of Engineer-in-Charge. -
68 E310.03.01 3 Nos x 1.5 sq. mm - M 16000.00 90.00 Nine Zero 1,440,000.00
69 E310.03.02 3 Nos x 2.5 sq. mm - M 7800.00 120.00 One Two Zero 936,000.00
70 E310.03.03 5 Nos x 1.5 sq. mm - M 21500.00 130.00 One Three Zero 2,795,000.00
71 E310.03.04 5 Nos x 2.5 sq. mm - M 11000.00 160.00 One Six Zero 1,760,000.00
72 E310.03.05 7 Nos x 1.5 sq. mm - M 6100.00 170.00 One Seven Zero 1,037,000.00
73 E310.03.06 7 Nos x 2.5 sq. mm - M 5900.00 230.00 Two Three Zero 1,357,000.00
74 E310.03.08 3 Nos x 4 sq. mm - M 1000.00 170.00 One Seven Zero 170,000.00
75 E310.03.09 5 Nos x 4 sq. mm - M 1000.00 290.00 Two Nine Zero 290,000.00
76 E310.04.00 Circuit wiring in non-hazardous areas using (size given below), copper conductor,
PVC insulated, FRLS outer sleeve cables (third core for earthing) from lighting
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 5 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-16-50-CJ-SOR- SOR Title Electrical Works Department ENGINEERING-ELECTRICAL

8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

panel/distribution junction box onwards including the supply of cable, junction boxes
and cable glands, including termination and connection, including all labour and
materials, as per approved drawings, specifications of this tender and directions of
Engineer-in-Charge. -
77 E310.04.04 3 C x 2.5 sq. mm armoured Cu cables. - M 15100.00 170.00 One Seven Zero 2,567,000.00
78 E310.07.00 Supply and laying of (surface type) approved make of black enamelled steel conduit
of following diameter and associated fittings from lighting/power panel, telephone, fire
alarm/plant communication points etc., including supply of G.I. sheet steel junction
boxes with acrylic cover, pull wire, including all labour and materials, as per approved
drawings, specifications of this tender and directions of Engineer-in-Charge. -
79 E310.07.01 25 mm diameter. - M 43000.00 170.00 One Seven Zero 7,310,000.00
80 E310.07.02 40 mm diameter. - M 30300.00 340.00 Three Four Zero 10,302,000.00
81 E310.09.00 Circuit wiring with 660 V grade (sizes given below) PVC insulated copper conductor
wires in already installed metsec channel including the supply of wires, termination,
connection and harnessing of wires etc., including all labour and materials, as per
approved drawings, specifications of this tender and directions of Engineer-in-Charge.
-
82 E310.09.01M01 1.5 sq. mm wires. in galvanised slotted channel trays. - M 187000.00 50.00 Five Zero 9,350,000.00
83 E310.09.03M01 4 sq. mm wires in galvanised slotted channel trays - M 6100.00 80.00 Eight Zero 488,000.00
84 E310.10.00 Supply and laying of (concealed type) PVC conduit of following diameter and
associated fittings in brick walls, RCC slabs/ceilings for lighting/ power/telephone, fire
alarm/plant communication points etc., including supply of G.I. sheet steel junction
boxes with acrylic cover, pull wire, making cuts and chasis in built up brick work, RCC
slabs/ceilings and making good the same, including all labour and materials, as per
approved drawings, specifications of this tender and directions of Engineer-in-Charge.
-
85 E310.10.01 25 mm diameter. - M 29100.00 100.00 One Zero Zero 2,910,000.00
86 E310.10.02 40 mm diameter. - M 2800.00 160.00 One Six Zero 448,000.00
87 E401.00.00 SOIL RESISTIVITY -
88 E401.01.00 Measurement of soil resistivity in accordance with IS:3043, including all labour and NOS 50.00 9,380.00 Nine Three Eight Zero 469,000.00
materials, as per approved drawings, specifications of this tender and at locations as
per directions of Engineer-in-Charge. -
89 E402.00.00 EARTH ELECTRODES -
90 E402.01.00 Supply, installation, testing and commissioning of GI earth electrodes, complete with
earth pit as per std. 7-51-0102 and all necessary materials including excavation of
earth pit, filling with charcoal and salt, back filling, providing necessary brickwork,
connections, including all labour and materials, as per approved drawings,
specifications of this tender and directions of Engineer-in-Charge. -
91 E402.01.01 GI earth electrode as per std. 7-51-0102. - NOS 1000.00 12,170.00 One Two One Seven 12,170,000.00
Zero
92 E403.00.00 EARTH STRIPS -
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 6 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-16-50-CJ-SOR- SOR Title Electrical Works Department ENGINEERING-ELECTRICAL

8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

93 E403.01.00 Supply, installation and connection of following GI earthing strip along the cable
trenches or cable trays or fixing to walls or structures including welding at joints,
providing anti-corrosive paint or bitumen and jute covering for welded portion,
clamping and necessary hardware for connecting, etc., including all labour and
materials, as per approved drawings, specifications of this tender and directions of
Engineer-in-Charge. -
94 E403.01.02 50 x 6 mm - M 200.00 350.00 Three Five Zero 70,000.00
95 E403.01.04 25 x 3 mm - M 24200.00 170.00 One Seven Zero 4,114,000.00
96 E403.02.00 Supply, installation and connection of following GI earthing strip buried individually at
a depth of 500 mm including welding at joints, providing anti-corrosive paint or
bitumen and jute covering for welded portion, clamping and necessary hardware for
connecting, excavation and refilling etc., including all labour and materials, as per
approved drawings, specifications of this tender and directions of Engineer-in-Charge.
-
97 E403.02.01 75 x 10 mm - M 9200.00 780.00 Seven Eight Zero 7,176,000.00
98 E403.02.02 50 x 6 mm - M 4500.00 450.00 Four Five Zero 2,025,000.00
99 E403.02.04 25 x 3 mm - M 100.00 290.00 Two Nine Zero 29,000.00
100 E405.00.00 EARTH PLATES -
101 E405.01.00 Supply, installation and connection of GI earth plates as per std. 7-51-0103, complete
with anchor bolts, including all labour and materials, as per approved drawings,
specifications of this tender and directions of Engineer-in-Charge. -
102 E405.01.01 GI earth plate as per std. 7-51-0103. - NOS 15.00 1,170.00 One One Seven Zero 17,550.00
103 E410.00.00 EARTHING CABLES -
104 E410.03.00 Supply of 1100 V grade, multi stranded Copper Conductor, XLPE/PVC insulated and
unarmoured cables (with green/yellow strips or green colour outer sleeve) of following
sizes as per EIL standard specification No. 6-51-0051, data sheet, specifications of
this tender and directions of Engineer-in-Charge. -
105 E410.03.01 1 C x 10 Sqmm - M 500.00 250.00 Two Five Zero 125,000.00
106 E410.04.00 Termination & connection of leads of 1100 V grade, multi stranded Copper
Conductor, XLPE/PVC insulated and unarmoured, cables of following sizes for
earthing of equipment, including supply of lugs, supply and fixing of GI saddles and
saddle bars, cutting and stripping of cable insulation, crimping the lug on to the
conductor, clamping of the cable, including all labour and materials as per approved
drawings, specifications of this tender and directions of Engineer-in-Charge -
107 E410.04.01 1 C x 10 Sqmm - NOS 500.00 300.00 Three Zero Zero 150,000.00
108 E501.00.00 PLANT COMMUNICATION SYSTEM -
109 E501.02.00 Installation, termination and connection of following plant communication system
(including back up battery bank, battery charger etc.), including transportation from
store/yard to site at the place of installation, assembling and installing in foundation or
fixing to wall/structure, aligning, levelling, grouting, cable termination, wiring and all
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 7 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-16-50-CJ-SOR- SOR Title Electrical Works Department ENGINEERING-ELECTRICAL

8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

inter-connection and making earth connection etc., first charging of battery, including
all labour and materials, as per approved drawings, specifications of this tender and
directions of Engineer-in-Charge. -
110 E501.02.01M01 Exchange Panel - NOS 8.00 12,500.00 One Two Five Zero 100,000.00
Zero
111 E501.02.02M01 Desk type intercom stations - NOS 26.00 2,500.00 Two Five Zero Zero 65,000.00
112 E501.02.02M02 Desk type intercom station with 64 keys. - NOS 8.00 3,000.00 Three Zero Zero Zero 24,000.00
113 E501.02.02M03 Desk type intercom station with 96 keys. - NOS 6.00 3,500.00 Three Five Zero Zero 21,000.00
114 E501.02.04 Weather Proof Intercom station with upto 3 Nos dual position Keys (FLP/Industrial NOS 70.00 2,500.00 Two Five Zero Zero 175,000.00
type). -
115 E501.02.05 Weather proof loudspeakers (FLP/Industrial Type). - NOS 70.00 700.00 Seven Zero Zero 49,000.00
116 E501.04.00 Supply of weatherproof type plant communication junction box (PAJB) suitable for
outdoor installation with Krone/screw type terminals, including supply of weatherproof
double compression cable glands and weatherproof plugs to block the unused entry
including all labour and materials, as per specifications of this tender and direction of
Engineer-in-Charge. -
117 E501.04.01V12 PAJB withIncoming 1 Nos , Incoming 20 Pair , Outgoing 5 Pair 5 Nos. , - NOS 21.00 25,000.00 Two Five Zero Zero Zero 525,000.00
118 E501.05.00 Installation, testing and commissioning of weatherproof type plant communication
junction box (PAJB) suitable for outdoor installation with Krone/screw type terminals,
including termination and connections of incoming and outgoing non-jelly cable,
excluding supply of weatherproof double compression cable glands, including all
labour and materials, as per specifications of this tender and direction of Engineer-in-
Charge. -
119 E501.05.01V14 PAJB with Incoming 1 Nos , Incoming 20 Pair , Outgoing 5 Pair 5 Nos. , - NOS 21.00 2,500.00 Two Five Zero Zero 52,500.00
120 E502.00.00 TELEPHONE DISTRIBUTION J.BOX (TDJB) -
121 E502.01.00 Supply, installation, testing and commissioning of Indoor Telephone Distribution J.B.
made out of 2.03 mm (14 gauge) sheet steel, with one anti-rust coat of primer, with
two finished coats of approved epoxy paint, with Krone type terminals with hinged
lockable door, detachable gland plate at the bottom/top complete with termination and
connections of incoming/ outgoing cables, including all labour and materials, as per
specifications of this tender and directions of Engineer-in-Charge. -
122 E502.01.04 TDJB Flush mounting type with an additional cable pull box at bottom for easy NOS 10.00 2,210.00 Two Two One Zero 22,100.00
termination of cable suitable for 5 pair incoming cable and 5 Nos. 1 pair outgoing wire.
-
123 E502.01.04V03 TDJB Flush mounting type with an additional cable pull box at bottom for easy NOS 4.00 8,300.00 Eight Three Zero Zero 33,200.00
termination of cable suitable forIncoming 1 Nos , Incoming 20 Pair , Outgoing 1 Pair
20 Nos. , -
124 E502.01.04V04 TDJB Flush mounting type with an additional cable pull box at bottom for easy NOS 5.00 5,040.00 Five Zero Four Zero 25,200.00
termination of cable suitable forIncoming 1 Nos , Incoming 10 Pair , Outgoing 1 Pair
10 Nos. , -
125 E502.01.04V10 TDJB Flush mounting type with an additional cable pull box at bottom for easy NOS 6.00 12,500.00 One Two Five Zero 75,000.00
termination of cable suitable forIncoming 1 Nos , Incoming 50 Pair , Outgoing 1 Pair Zero
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 8 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-16-50-CJ-SOR- SOR Title Electrical Works Department ENGINEERING-ELECTRICAL

8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

50 Nos. , -
126 E502.01.04V11 TDJB Flush mounting type with an additional cable pull box at bottom for easy NOS 2.00 20,000.00 Two Zero Zero Zero 40,000.00
termination of cable suitable forIncoming 1 Nos , Incoming 100 Pair , Outgoing 1 Pair Zero
100 Nos. , -
127 E502.02.00 Supply, installation, connection, testing and commissioning of following plug - in type
sockets for Telephones extensions including supply of sheet boxes with covers
connection of socket and plug, including all labour and materials, as per approved
drawings, specifications of this tender and directions of Engineer-in-Charge. -
128 E502.02.02 Flush Mounting Type. - NOS 300.00 730.00 Seven Three Zero 219,000.00
129 E502.03.00 Wiring with (No. of wires given below) 660 V grade, 0.63 mm dia. annealed tinned
copper conductor, PVC insulated twin flat wire as per relevant IS in already laid
surface/concealed conduit from TDJB onwards to telephone sockets including supply
of Wires, termination and connection, including all labour and materials, as per
approved drawings, specifications of this tender and directions of Engineer-in-Charge.
-
130 E502.03.01 1 No. twin flat wire. - M 3500.00 60.00 Six Zero 210,000.00
131 E502.03.02 2 Nos. twin flat wires. - M 2500.00 70.00 Seven Zero 175,000.00
132 E502.03.03 3 Nos. twin flat wires. - M 1200.00 90.00 Nine Zero 108,000.00
133 E502.03.04 4 Nos. twin flat wires. - M 820.00 90.00 Nine Zero 73,800.00
134 E502.03.05 5 Nos. twin flat wires. - M 100.00 100.00 One Zero Zero 10,000.00
135 E503.00.00 FIRE ALARM SYSTEM -
136 E503.02.00 Installation, termination and connection of following fire alarm panel including Power
Pack and battery backup system and all associated items, including transportation
from store/yard to site at the place of installation, assembling and installation on
foundation or fixing to wall or steel structures, aligning, levelling, grouting, termination
and connection of cables, making earth connections etc., including all labour and
materials, as per approved drawings, specifications of this tender and directions of
Engineer-in-Charge. -
137 E503.02.01 Fire alarm panel. - NOS 12.00 6,620.00 Six Six Two Zero 79,440.00
138 E503.02.05 Heat detectors. - NOS 60.00 290.00 Two Nine Zero 17,400.00
139 E503.02.10 Break glass type fire alarm boxes. - NOS 120.00 830.00 Eight Three Zero 99,600.00
140 E503.02.12 Exit signs. - NOS 210.00 390.00 Three Nine Zero 81,900.00
141 E503.02.14 Hooters. - NOS 130.00 390.00 Three Nine Zero 50,700.00
142 E503.02.15 Sirens with starters. - NOS 3.00 840.00 Eight Four Zero 2,520.00
143 E503.02.16 Multi sensor type detectors - NOS 4200.00 560.00 Five Six Zero 2,352,000.00
144 E503.02.17 Fault Isolator modules - NOS 220.00 730.00 Seven Three Zero 160,600.00
145 E503.03.00 Supply of weatherproof type fire alarm junction box (FAJB) suitable for outdoor
installation with Krone/screw type terminals, including supply of weatherproof double
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 9 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-16-50-CJ-SOR- SOR Title Electrical Works Department ENGINEERING-ELECTRICAL

8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

compression cable glands and weatherproof plugs to block the unused entry including
all labour and materials, as per specifications of this tender and direction of Engineer-
in-Charge. -
146 E503.03.01V09 FAJB with Incoming 1 Nos , Incoming 2 Pair , Outgoing 2 Pair 1 Nos. , - NOS 2.00 4,500.00 Four Five Zero Zero 9,000.00
147 E503.03.01V10 FAJB with Incoming 2 Nos , Incoming 2 Pair , Outgoing 2 Pair 2 Nos. , - NOS 14.00 5,500.00 Five Five Zero Zero 77,000.00
148 E503.04.00 Installation, testing and commissioning of weatherproof type fire alarm junction box
(FAJB) suitable for outdoor installation with Krone/screw type terminals, including
termination and connections of incoming and outgoing non-jelly cable, excluding
supply of weatherproof double compression cable glands, including all labour and
materials, as per specifications of this tender and direction of Engineer-in-Charge. -
149 E503.04.01V13 FAJB with Incoming 1 Nos , Incoming 2 Pair , Outgoing 2 Pair 1 Nos. , - NOS 2.00 450.00 Four Five Zero 900.00
150 E503.04.01V14 FAJB with Incoming 2 Nos , Incoming 2 Pair , Outgoing 2 Pair 2 Nos. , - NOS 14.00 550.00 Five Five Zero 7,700.00
151 E801.00.00 LAN Systems
-
152 E801.01.00 Supply, installation, connection, testing and
commissioning of weatherproof power panels for UPS power distribution having
following incomer & outgoing feeders, including
all labour and materials, as per approved drawings,
specifications of this tender and directions of engineer-incharge.
-
153 E801.01.01 32A, double pole incomer MCB isolator and 6 nos outgoing double pole 10A MCBs NOS 25.00 12,690.00 One Two Six Nine Zero 317,250.00
isolator with 2nos, 10A semiconducting fuses -
154 E801.01.02 32A, double pole incomer MCB isolator and 12 nos outgoing double pole 10A MCBs NOS 2.00 16,000.00 One Six Zero Zero Zero 32,000.00
isolator with 2 nos, 10A semiconducting fuses , -
155 E801.01.03 63A, double pole incomer MCB isolator and 18 nos outgoing double pole 10A MCBs NOS 2.00 18,200.00 One Eight Two Zero 36,400.00
isolator with 2 nos, 10A semiconducting fuses - Zero
156 E801.02.00 Supply, installation, termination, testing and NOS 300.00 670.00 Six Seven Zero 201,000.00
commissioning of flush mounted CAT-6 UTP JACK
(Information Outlets) including supply of all connected materials(i.e Face plates,
Surface mount box, patch cord at I/O end), including all labour and materials, as per
approved drawings, specifications of this tender and directions of Engineer-in-charge.
-
157 E801.03.00 Circuit wiring with following cables for LAN in already laid surface/concealed conduit
from Etherswitch rack onwards to Cat-6 UTP Jack (Information outlet) including the
supply of cables, termination and connection at both ends (i.e at jack panel end & at
the I/O end), including all labour and materials, as per approved drawings,
specifications of this tender and directions of Engineer-in-charge. -
158 E801.03.01 1 no. CAT-6 UTP cable - M 3650.00 70.00 Seven Zero 255,500.00
159 E801.03.02 2 nos. CAT-6 UTP cable - M 2350.00 120.00 One Two Zero 282,000.00
160 E801.03.03 3 nos. CAT-6 UTP cable - M 1000.00 170.00 One Seven Zero 170,000.00
161 E801.03.04 4 nos. CAT-6 UTP cable - M 1000.00 230.00 Two Three Zero 230,000.00

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 10 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-16-50-CJ-SOR- SOR Title Electrical Works Department ENGINEERING-ELECTRICAL

8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

162 E801.03.05 5 nos. CAT-6 UTP cable - M 100.00 250.00 Two Five Zero 25,000.00
163 E999.00.00 Miscellaneous -
164 E999.99.00 Miscellaneous -
165 E999.99.99V14 Cabling with 1100V grade, 3C x 2.5 sq mm Cu conductor, XLPE Insulated, FRLS M 9000.00 80.00 Eight Zero 720,000.00
outer sheath, unarmoured cable as per EIL standards & specification no. 6-51-0051,
datasheet in already laid surface/concealed conduit from DGFAP/FAJB onwards,
termination and connection, including supply of cables, including all labour and
material, as per approved drawings, specifications of this tender & directions of
Engineer-In-Charge. -
166 E999.99.99V16 Wiring with 660V grade, 5 Pair, 0.9 mm dia, PVC insulated,FRLS outer sheath, M 5650.00 190.00 One Nine Zero 1,073,500.00
annealed, tinned, high conductivity Cu conductor unarmoured cable as per EIL
standards & specification no. 6-51-0052, datasheet in already laid surface/concealed
conduit from Exchange/PAJB onwards, termination and connection, including supply
of cables, including all labour and materials, as per approved drawings, specifications
of this tender & directions of Engineer-In-Charge. -
167 E999.99.99V17 Wiring with 660V grade, 2 Pair, 1.5 Sqmm, PVC insulated, FRLS outer sheath, M 43300.00 190.00 One Nine Zero 8,227,000.00
annealed, tinned, high conductivity Cu conductor unarmoured cable as per EIL
standards & specification no. 6-51-0052, datasheet, in already laid surface/concealed
conduit from
FA panel/FAJB onwards to fire alarm equipment, termination and connection,
including supply of cables, including all labour and
materials, as per approved drawings, specifications of this tender & directions of
Engineer-In-Charge. -
SOR Level Total: 194,754,590.00

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 11 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

1 QQ MECHANICAL EQUIPMENT -
2 Q999.00.00 Miscellaneous -
3 Q999.99.00 Miscellaneous -
4 Q999.99.99V01 HVAC System for Main Control Room LOT 1.00 32,550,000.00 Three Two Five Five 32,550,000.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Main Control Room. Central
Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 300TR minimum)
B. 4 nos. AHU (Capacity 33000cfm each)
C. 4 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 4000cfm each)
D. 18 G duct works : 2300 sq. m
E. Combined Fire and Smoke Damper: 17 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
5 Q999.99.99V02 HVAC System for Control Room N2 Plant LOT 1.00 8,703,750.00 Eight Seven Zero Three 8,703,750.00
Design, engineering, manufacture, procurement of raw materials and bought out Seven Five Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 12 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Control Room N2 Plant.
Central Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 75TR minimum )
B. 1 nos. AHU (Capacity 33000cfm each)
C. 1 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 2400cfm each)
D. 18 G duct works : 550 sq. m
E. Combined Fire and Smoke Damper: 3 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
6 Q999.99.99V03 HVAC System for Control Room-89 (OMS) LOT 1.00 7,653,750.00 Seven Six Five Three 7,653,750.00
Design, engineering, manufacture, procurement of raw materials and bought out Seven Five Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Control Room-89 (OMS).
Central Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 75TR minimum )
B. 1 nos. AHU (Capacity 38000cfm each)
C. 1 no. Chemical filter unit with 1 working+ 1 standby
blowers (Capacity 2400cfm each)
D. 18 G duct works : 200 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
7 Q999.99.99V04 HVAC System for Control Room-90 (WATER BLOCK) LOT 1.00 10,534,800.00 One Zero Five Three 10,534,800.00
Design, engineering, manufacture, procurement of raw materials and bought out Four Eight Zero Zero
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 13 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

components, fabrication, assembly at shop, shop painting, inspection, testing at

manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants/consumables/lubricants for HVAC system including all associated piping
and valves/instruments, transportation from vendor's works to site, unloading at site,
handling, transportation to contractor's store and from contractor's store to work site,
storage at site, assembly at site, installation of HVAC equipment including supply air
and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No. B018-000-81-41-SOW-8105), Job specification (Doc. No.
B018- 000-80-42-SP-8105), Data sheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Control Room-90 (WATER
BLOCK). Air-conditioning system consisting of following major items:
A. 16.5 TR x 8300CFM min. actual capacity - 4 nos. (3 W + 1S) Air cooled package
AC.
B. 18 G duct works: 150 Sq. M
C. Combined Fire and Smoke Damper: 5 nos.
-
8 Q999.99.99V05 HVAC System for Control Room-91 (ETP) LOT 1.00 10,534,800.00 One Zero Five Three 10,534,800.00
Design, engineering, manufacture, procurement of raw materials and bought out Four Eight Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants/consumables/lubricants for HVAC system including all associated piping
and valves/instruments, transportation from vendor's works to site, unloading at site,
handling, transportation to contractor's store and from contractor's store to work site,
storage at site, assembly at site, installation of HVAC equipment including supply air
and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No. B018-000-81-41-SOW-8105), Job specification (Doc. No.
B018- 000-80-42-SP-8105), Data sheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Control Room-91 (ETP). Air-
conditioning system consisting of following major items:
A. 16.5 TR x 8300CFM min. actual capacity - 4 nos. (3 W + 1S) water cooled package
AC.
B. 18 G duct works: 150 Sq. M
C. Combined Fire and Smoke Damper: 5 nos.
-
9 Q999.99.99V06 HVAC System for Satellite Rack Room-81 (DFCU) LOT 1.00 9,364,500.00 Nine Three Six Four Five 9,364,500.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 14 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

manufacturer's works, packing and delivery including supply of all commissioning

spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Satellite Rack Room-81
(DFCU). Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 90TR minimum )
B. 2 nos. AHU (Capacity 22000cfm each)
C. 1 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 2400cfm each)
D. 18 G duct works : 300 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
10 Q999.99.99V07 HVAC System for Satellite Rack Room-82 (DFCU) LOT 1.00 9,364,500.00 Nine Three Six Four Five 9,364,500.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Satellite Rack Room-82
(DFCU). Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 90TR minimum )
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 15 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

B. 2 nos. AHU (Capacity 22000cfm each)

C. 1 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 2400cfm each)
D. 18 G duct works : 300 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)

-
11 Q999.99.99V08 HVAC System for Satellite Rack Room-83 (LLDPE/HDPE SWING) LOT 1.00 9,364,500.00 Nine Three Six Four Five 9,364,500.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Satellite Rack Room-83
(LLDPE/HDPE SWING). Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 90TR minimum )
B. 2 nos. AHU (Capacity 22000cfm each)
C. 1 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 2400cfm each)
D. 18 G duct works : 300 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
12 Q999.99.99V09 HVAC System for Satellite Rack Room-84 (LLDPE/HDPE SWING) LOT 1.00 9,364,500.00 Nine Three Six Four Five 9,364,500.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 16 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Satellite Rack Room-84
(LLDPE/HDPE SWING). Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 90TR minimum )
B. 2 nos. AHU (Capacity 22000cfm each)
C. 1 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 2400cfm each)
D. 18 G duct works : 300 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
13 Q999.99.99V10 HVAC System for Satellite Rack Room-85 (HDPE) LOT 1.00 9,364,500.00 Nine Three Six Four Five 9,364,500.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Satellite Rack Room-85
(HDPE). Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 90TR minimum )
B. 2 nos. AHU (Capacity 22000cfm each)
C. 1 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 2400cfm each)
D. 18 G duct works : 300 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 17 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

F. Chilled water Pumps (1 working+ 1 standby)

G. Condensate return Pumps (1 working+ 1 standby)
-
14 Q999.99.99V11 HVAC System for Satellite Rack Room-86 (PPU) LOT 1.00 9,364,500.00 Nine Three Six Four Five 9,364,500.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Satellite Rack Room-86 (PPU).
Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 90TR minimum )
B. 2 nos. AHU (Capacity 22000cfm each)
C. 1 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 2400cfm each)
D. 18 G duct works : 300 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
15 Q999.99.99V12 HVAC System for Sub-Station-81(DFCU) LOT 1.00 18,990,000.00 One Eight Nine Nine Zero 18,990,000.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 18 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and

other documents referred therein for HVAC System of Sub-Station-81(DFCU). Central
Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 180 TR minimum )
B. 2 nos. AHU (Capacity 33000cfm each)
C. 2 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 4000cfm each)
D. 18 G duct works : 1200 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
16 Q999.99.99V13 HVAC System for Sub-Station-82(DFCU) LOT 1.00 18,990,000.00 One Eight Nine Nine Zero 18,990,000.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Sub-Station-82(DFCU). Central
Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 180 TR minimum )
B. 2 nos. AHU (Capacity 33000cfm each)
C. 2 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 4000cfm each)
D. 18 G duct works : 1200 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)

-
17 Q999.99.99V14 HVAC System for Sub-Station-83 (LLDPE/HDPE SWING) LOT 1.00 18,990,000.00 One Eight Nine Nine Zero 18,990,000.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero Zero
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 19 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

components, fabrication, assembly at shop, shop painting, inspection, testing at

manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System Sub-Station-83 (LLDPE/HDPE
SWING). Central Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 180 TR minimum )
B. 2 nos. AHU (Capacity 33000cfm each)
C. 2 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 4000cfm each)
D. 18 G duct works : 1200 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
18 Q999.99.99V15 HVAC System for Sub-Station-84 (LLDPE/HDPE SWING) LOT 1.00 18,990,000.00 One Eight Nine Nine Zero 18,990,000.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Sub-Station-84 (LLDPE/HDPE
SWING). Central Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 20 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

(VAM)- (Actual Cooling capacity 180 TR minimum )

B. 2 nos. AHU (Capacity 33000cfm each)
C. 2 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 4000cfm each)
D. 18 G duct works : 1200 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
19 Q999.99.99V16 HVAC System for Sub-Station-85 (HDPE) LOT 1.00 18,990,000.00 One Eight Nine Nine Zero 18,990,000.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Sub-Station-85 (HDPE).
Central Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 180 TR minimum )
B. 2 nos. AHU (Capacity 33000cfm each)
C. 2 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 4000cfm each)
D. 18 G duct works : 1200 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
20 Q999.99.99V17 HVAC System for Sub-Station-86 (PPU) LOT 1.00 18,990,000.00 One Eight Nine Nine Zero 18,990,000.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 21 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Sub-Station-86 (PPU). Central
Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 180 TR minimum )
B. 2 nos. AHU (Capacity 33000cfm each)
C. 2 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 4000cfm each)
D. 18 G duct works : 1200 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
21 Q999.99.99V18 HVAC System for Sub-Station-87(CT-01-CRACKER) LOT 1.00 18,990,000.00 One Eight Nine Nine Zero 18,990,000.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Sub-Station-87(CT-01-
CRACKER). Central Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 180 TR minimum )
B. 2 nos. AHU (Capacity 33000cfm each)
C. 2 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 4000cfm each)
D. 18 G duct works : 1200 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 22 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

F. Chilled water Pumps (1 working+ 1 standby)

G. Condensate return Pumps (1 working+ 1 standby)

-
22 Q999.99.99V19 HVAC System for Sub-Station-88(CT-02-POLYMER) LOT 1.00 15,570,000.00 One Five Five Seven 15,570,000.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Sub-Station-88(CT-02-
POLYMER). Central Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 140 TR minimum )
B. 2 nos. AHU (Capacity 22000cfm each)
C. 2 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 3300cfm each)
D. 18 G duct works : 1200 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
23 Q999.99.99V20 HVAC System for Sub-Station-90(WATER BLOCK) LOT 1.00 26,940,000.00 Two Six Nine Four Zero 26,940,000.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 23 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Sub-Station-90(WATER
BLOCK). Central Air-conditioning system consisting of following major items:

A. 2 nos. (1W+1S) Vapour compression chiller/condensing unit (Air cooled) - (Actual

Cooling capacity 140 TR minimum of each)
B. 2 nos. AHU (Capacity 25000cfm each)
C. 2 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 3300cfm each)
D. 18 G duct works : 1000 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby) in case of chiller.
-
24 Q999.99.99V21 HVAC System for Sub-Station-91(ETP) LOT 1.00 10,564,500.00 One Zero Five Six Four 10,564,500.00
Design, engineering, manufacture, procurement of raw materials and bought out Five Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Sub-Station-91(ETP). Central
Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 90 TR minimum )
B. 1 nos. AHU (Capacity 33000cfm each)
C. 1 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 4000cfm each)
D. 18 G duct works : 700 sq. m
E. Combined Fire and Smoke Damper: 5 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
25 Q999.99.99V22 HVAC System for Main Receiving Sub-Station LOT 1.00 31,650,000.00 Three One Six Five Zero 31,650,000.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 24 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

manufacturer's works, packing and delivery including supply of all commissioning

spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants / consumables / lubricants for HVAC system including all associated
piping and valves/instruments, transportation from vendor's works to site, unloading at
site, handling, transportation to contractor's store and from contractor's store to work
site, storage at site, assembly at site, installation of HVAC equipment including supply
air and return air ducting, diffusers, grills, dampers, heater, pan-humidifier, associated
piping and valves/instruments, hook up, testing, painting, insulation, commissioning,
performance guarantee run test at site, handing over to client and other field works
including civil structural work complete in all respect as per the enclosed Scope of
Supply and Work (Doc. No.B018-000- 81-41-SOW-8105), Job Specification (Doc. No.
B018- 000-80-42-SP-8105), Datasheets (Doc. No. B018-000-80-42-DS-8105) and
other documents referred therein for HVAC System of Main Receiving Sub-Station.
Central Air-conditioning system consisting of following major items:

A. One (1) no. single effect Vapour Absorption Machine

(VAM)- (Actual Cooling capacity 300TR minimum )
B. 3 nos. AHU (Capacity 33000cfm each)
C. 3 no. Chemical filter units with 1 working+ 1 standby
blowers (Capacity 4500cfm each)
D. 18 G duct works : 2000 sq. m
E. Combined Fire and Smoke Damper: 7 nos.
F. Chilled water Pumps (1 working+ 1 standby)
G. Condensate return Pumps (1 working+ 1 standby)
-
26 Q999.99.99V23 Floor mounted Split Air conditioner - 3TR LOT 1.00 15,600,000.00 One Five Six Zero Zero 15,600,000.00
Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants/ lubricants for air-conditioning system and, transportation from vendor's
works to site, unloading at site, handling, transportation to contractor's store and from
contractor's store to work site, storage at site, assembly at site, installation, hook up,
testing, painting, insulation, commissioning, performance guarantee run test at site,
handing over to client and other field works including civil/structural work complete in
all respect as per the enclosed Scope of Supply and Work (Doc. No. B018-000- 81-
41-SOW-8105), Job specification (Doc. No. B018- 000-80-42-SP-8105) and other
documents refereed therein for Air-conditioning System. Each Split Air conditioner
shall be provided with 10m Power supply cable and 15m drain piping. Distance
between indoor and outdoor unit may be upto 20m (maximum).

Total 130 Numbers Floor mounted Tower Split Air Conditioner of capacity 3 TR each
for commissioning/General purpose of control rooms and SRR Buidings.
-
27 Q999.99.99V24 Wall mounted Split Air conditioner - 2TR LOT 1.00 5,280,000.00 Five Two Eight Zero Zero 5,280,000.00
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 25 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-80-42-CJ-SOR- SOR Title Mechanical Eqpt Works Department STATIC & MACHINERY EQUP -1
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

Design, engineering, manufacture, procurement of raw materials and bought out Zero Zero
components, fabrication, assembly at shop, shop painting, inspection, testing at
manufacturer's works, packing and delivery including supply of all commissioning
spares, special tools and tackles as applicable, mandatory spares, first fill of
refrigerants/ lubricants for air-conditioning system and, transportation from vendor's
works to site, unloading at site, handling, transportation to contractor's store and from
contractor's store to work site, storage at site, assembly at site, installation, hook up,
testing, painting, insulation, commissioning, performance guarantee run test at site,
handing over to client and other field works including civil/structural work complete in
all respect as per the enclosed Scope of Supply and Work (Doc. No. B018-000- 81-
41-SOW-8105), Job specification (Doc. No. B018- 000-80-42-SP-8105) and other
documents refereed therein for Air-conditioning System. Each Split Air conditioner
shall be provided with 10m Power supply cable and 15m drain piping. Distance
between indoor and outdoor unit may be upto 20m (maximum).

Total 66 Numbers wall mounted Tower Split Air Conditioner of capacity 2 TR each for:

Satellite Rack Rooms:60 Nos (for 6 nos. SRR building)

Control Room -Extension (Truck Gantry) building: 6 Nos.

-
28 Q999.99.99V25 Supply, Installation, Testing, Commissioning and insulation of 18 Gauge GI Ducting SQM 1.00 1,200.00 One Two Zero Zero 1,200.00
for Air conditioning system (These prices are for the purpose of adjustment in price in
case of variation in ducting quantities) -
SOR Level Total: 364,699,800.00

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 26 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

1 A000.00.00 ARCHITECTURE -
2 A002.00.00 FLOOR FINISHING -
3 A002.01.00 Providing and laying average 25mm cement concrete flooring in panels consisting of
base course of 1:2:4 grade cement concrete (6mm down size stone aggregate) laid
over sub-base of cement concrete and finishing with a layer of floating coat of neat
cement slurry @ 2.75kg. of cement per Sq. M. of area including cleaning the sub-
base surface, applying neat cement slurry @ 2.75 kg of cement per Sq. M. of area
over the sub- base to receive the base course, compacting, tamping, trowelling,
finishing, curing, providing, shuttering to the edges etc. all complete -
4 A002.01.01 CEMENT SUPPLIED BY THE CONTRACTOR AT THEIR COST - Sq.M. 16250.00 290.00 Two Nine Zero 4,712,500.00
5 A002.02.00 Providing and laying cement concrete granolithic flooring in panels consisting of base
course (under layer of 1:2:4 grade cement concrete, 6mm down size stone
aggregates) laid over sub-base, wearing top- layer of cement mortar (1 cement: 3
coarse sand by volume) finished smooth by tamping, trowelling, and with a finishing
floating coat of neat cement slurry @ 2.75kg. of cement per Sq. M. of area including
cleaning the sub-base surface, applying neat cement slurry over the sub- base @
2.75Kg of cement per Sq. M of area to receive the base course, compacting, tamping,
trowelling, finishing, curing, providing, shuttering to the edges etc. all complete. -
6 A002.02.01 With average 25mm thick under-layer and 15mm thick top layer. CEMENT Sq.M. 18565.00 360.00 Three Six Zero 6,683,400.00
SUPPLIED BY THE CONTRACTOR AT THEIR COST. -
7 A002.03.00 Providing and laying average 50mm thick heavy duty flooring in panels consisting of
base course of 35mm thick cement concrete (1 cement : 1.5 coarse sand : 3.5 stone
aggregates of 10mm to 6mm size by volume) laid over sub-base and 15mm thick
finishing layer consisting of cement and integral hardening compound mixed in ratio of
4 cement :1 hardenar (by weight) :2 stone agrgregates of 6mm and down size laid
integral with base course and finished smooth including cleaning the sub-base
surface, applying neat cement slurry @2.75 Kg of cement per Sq.M of area over sub-
base to receive the base course, levelling, tamping, trowelling, finishing, curing,
providing shuttering to the edges etc. all complete. -
8 A002.03.01 CEMENT SUPPLIED BY THE CONTRACTOR AT THEIR COST. - Sq.M. 21270.00 480.00 Four Eight Zero 10,209,600.00
9 A002.04.00 Providing and laying 125mm high cement plaster skirting with 1:3 cement mortar (1
cement : 3 coarse sand by volume) finished with a floating coat of neat cement slurry
@ 2.75kg. of cement per Sq.M of area including rounding of junctions with floor,
preparing the wall surface, making recess in the wall, finishing, curing etc. all
complete. -
10 A002.04.01 18mm thick. CEMENT SUPPLIED BY THE CONTRACTOR AT THEIR COST. - RM 9965.00 50.00 Five Zero 498,250.00
11 A002.06.00 Providing and fixing panel dividers in flooring/dado including maintaining slope, line,
chipping of the uneven base, grinding etc. all complete. -
12 A002.06.04 P.V.C. panel dividers ( 3mm x 20mm size.) - RM 23450.00 50.00 Five Zero 1,172,500.00
13 A002.06.05 P.V.C. panel dividers ( 3mm x 35mm size.) - RM 28010.00 60.00 Six Zero 1,680,600.00
14 A002.06.06 P.V.C. panel dividers ( 3mm x 40mm size.) - RM 31430.00 65.00 Six Five 2,042,950.00

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 27 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

15 A002.10.00 Providing and laying machine cut chissel dressed kota stone slab of approved shade
in floor tread, landing, riser, skirting, dado over and including a bed of cement mortar
including preparing the base surface, applying neat cement slurry @ 2.75 Kg of
cement per Sq.M of area to receive the mortar, providing neat cement slurry @ 4.4kg.
of cement /Sq.M of area over the mortar bed, jointing each slab with neat cement
paste/ grouting white cement and pigment ( conforming to IS : 2114, Table-1,
matching the shade of slabs), machine cutting of the slab edges square, true & plumb
finishing, grinding, polishing, finishing etc. all complete. -
16 A002.10.01 25mm thick kota stone slab (with tolerance +_2mm for thickness, +_2mm for length/ Sq.M. 3360.00 1,250.00 One Two Five Zero 4,200,000.00
breadth) in floor, landing tread over average 15mm thick cement mortar 1:4(1 Cement
: 4 coarse sand by volume). CEMENT SUPPLIED BY THE CONTRACTOR AT
THEIR COST. -
17 A002.10.03 18mm thick kota stone slab in riser, dado, skirting over average12mm thick cement Sq.M. 470.00 1,380.00 One Three Eight Zero 648,600.00
mortar1:3(1 cement:3 coarse sand by volume). CEMENT SUPPLIED BY THE
CONTRACTOR AT THEIR COST. -
18 A002.10.05 Extra for providing round nosing by machine cutting of the slab. - RM 1760.00 160.00 One Six Zero 281,600.00
19 A002.11.00 Providing and laying tiles in flooring , dado, skirting etc. in approved colour, design
and pattern, laid over and including a coating of approved adhesive as per
manufacturers specifications, flush pointing of joints of tiles with cement paste/
grouting with white cement and pigment (conforming to IS:2114, Table-1, matching
the shade of tiles) finishing, cleaning etc. all complete. -
20 A002.11.05 Ceramic, matt finished non-slip type tiles of approved make and shade(s) in approved Sq.M. 230.00 1,530.00 One Five Three Zero 351,900.00
design/ pattern including cleaning the finished surface with oxalic acid, wax polishing
etc. for size 300mm x 300mm x 8mm (+5%) thick tiles for flooring. -
21 A002.11.06 Ceramic, matt/ glazed/ semi-glazed finished tiles of approved make & shade(s) in Sq.M. 1090.00 1,400.00 One Four Zero Zero 1,526,000.00
approved design/ pattern including cleaning the finished surface with oxalic acid, wax
polishing etc. for size 300mm x 450mm x 8.5mm thick (minimum) tiles -
22 A002.11.07 Decorative, matt/ mirror finish homogeneous double charge Vitrified porcelain tiles of Sq.M. 1500.00 1,530.00 One Five Three Zero 2,295,000.00
minimum size 600mm x 600mm x 10mm thick in approved quality, colour, make,
design/ pattern -
23 A002.11.07M01 Decorative, matt/ mirror finish homogeneous double charge Vitrified porcelain tiles of Sq.M. 2000.00 1,250.00 One Two Five Zero 2,500,000.00
minimum size 900mm x 900mm x 10mm thick in approved quality, colour, make,
design/ pattern -
24 A002.11.10 Decorative, matt/ mirror finish Vitrified porcelain tiles in approved quality, colour(s), Sq.M. 11170.00 1,300.00 One Three Zero Zero 14,521,000.00
make, design/ pattern., laid with 4mm gaps all round each tile, provided with approved
3mm PVC spacer (cross-shaped, T-shaped and L-shaped- as required), including
removing the spacers after setting, providing dust resistant self-levelling flowable
epoxy grout in the joints¿ gap (4mm) in approved shade, cleaning, finishing the
finished surface with oxalic acid etc. (of minimum size 600mm x 600mm x 10mm
thick) -
25 A002.15.00 Providing and applying pigmented (approved shade) chemical and abrasion resistant, Sq.M. 1155.00 1,400.00 One Four Zero Zero 1,617,000.00
solvent based self levelling floor coating based on epoxy resin with amine curing
agents, in 2 coats @ 125 gms/sq.m. (min.)per coat by brush or spraying over a
levelling screed (min. 3mm thick) of a 3 part solvent free combination of epoxy resin,
amine hardeners and graded chemically inert aggregate filler, laid over a coat of 2-
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 28 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

part epoxy resin primer applied over existing flooring etc. all as per manufacturer's
specifications. -
26 A002.16.00 Providing and applying pigmented (approved shade) chemical and abrasion resistant, Sq.M. 2010.00 250.00 Two Five Zero 502,500.00
solvent based coating (on dado/wall) of epoxy resin with amine curing agents, in 2
coats @ 125 gms/sq.m. (min.) per coat by brush over plastering/ concrete surfaces
including surface preparation, curing etc. all as per manufacturer's specification. -
27 A002.17.00 Providing and laying minimum 18mm thick approved premium quality and shade
polished granite stone slabs in flooring, counters, treads, risers, skirting, dado etc.
over and including a bed of cement mortar including preparing the base surface,
applying neat cement slurry @ 2.75 kg. of cement per sq. mtr. of area to receive the
mortar bed, jointing each slab with neat cement paste/ grout with white cement
maixed with pigment (conforming to IS:2114, Table-1) to match the colour of the
granite stone slabs, finishing etc. all complete. -
28 A002.17.01 Granite stone slabs in flooring, counters, treads etc.(perfectly levelled) over and Sq.M 2380.00 3,650.00 Three Six Five Zero 8,687,000.00
including a bed of cement mortar 1:4 (1 cement: 4 coarse sand by volume) CEMENT
SUPPLIED BY THE CONTRACTOR AT THEIR COST. -
29 A002.17.03 Granite stone slabs in risers, skirting, dado etc. over and including a bed of cement Sq.M 1195.00 3,650.00 Three Six Five Zero 4,361,750.00
mortar 1:3 (1cement: 3 coarse sand by volume) CEMENT SUPPLIED BY THE
CONTRACTOR AT THEIR COST. -
30 A002.17.05 Extra for round nosing/ moulded edges (as per approved design) to Granite stone RM 560.00 260.00 Two Six Zero 145,600.00
slabs. -
31 A003.00.00 WOOD WORK -
32 A003.01.00 Providing and fixing wooden frames of doors, windows, ventilators including cutting,
shaping, jointing, applying a coat of bituminous paint on concealed surface, wood
primer on exposed surface, fixing in masonry/RCC by means of 300mm x 25mm x
6mm thick M.S. hold fasts screwed to frame @ 600mm max vertically and grouted
with M-15 grade concrete in min. 350mm x 100mm x 100mm sized hole made in
masonry/96mm long, 12mm dia M.S. dash fastener, painting with two coats of
approved shade and make (ICI or equivalent) synthetic enamel paint over approved
quality primer coat, finishing etc. all complete. -
33 A003.01.01 Wooden frames with second class teak wood conforming to IS : 4021. - Cu.M. 1.00 130,000.00 One Three Zero Zero 130,000.00
Zero Zero
34 A003.02.00 Providing and fixing Factory made, overall 35mm thick block board flush shutter
consisting of solid core block board bonded with phenol phormaldehyde synthetic
resin conforming to IS : 848 and faced on both faces with commercial type
plywood/teakwood veneering/ lamination bonded with phenol formaldehyde synthetic
resin conforming to IS : 848, including providing and fixing second class teakwood
perimeter beading fixed by means of approved quality neoprene based adhesive and
nailing @ 300 mm max.. painting exposed surface with two coats of approved shade
and make synthetic enamel paint over approved quality primer coat, providing and
fixing 125mm long M.S. butt hinges [for each shutter (vertical spacing not exceeding
600mm)] including fixing with door frame, finishing etc. all conforming to IS : 2202. -
35 A003.02.03 Door shutter faced with 1mm thick approved quality lamination of approved Sq.M. 15.00 3,820.00 Three Eight Two Zero 57,300.00
shade/brand. -

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 29 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

36 A003.07.00 Providing and fixing in position following items including all necessary fixtures, fittings,
finishing etc. all complete. -
37 A003.07.01 Approved make heavy duty overhead hydraulic door closer with adjustable spanners, Unit 22.00 1,060.00 One Zero Six Zero 23,320.00
metal screws etc. conforming to IS : 3564 -
38 A003.07.02 Approved make Chromium plated metallic (brass body) mortice lock, 6 levers Unit 20.00 1,930.00 One Nine Three Zero 38,600.00
conforming to IS : 2209 (inclusive of pair of handles of pressure die cast zinc
alloy,satin finished). -
39 A003.07.06 Approved make pressure die cast zinc alloy, chromium plated door handle. 300 mm Unit 20.00 440.00 Four Four Zero 8,800.00
long. -
40 A003.07.09 Approved quality anodized aluminium aldrop 300mm long, 19.05mm dia in bronze Unit 11.00 390.00 Three Nine Zero 4,290.00
colour. -
41 A003.07.10 Approved quality anodized aluminium tower bolts conforming to IS-204 in Bronze Unit 40.00 210.00 Two One Zero 8,400.00
colour, 250 x 10mm. -
42 A003.07.11 Approved quality anodized aluminium tower bolts conforming to IS-204 in Bronze Unit 28.00 140.00 One Four Zero 3,920.00
colour, 150 x 10mm. -
43 A003.07.12 Approved quality zinc alloy pressure die cast, chromium plated spring loaded round Unit 28.00 300.00 Three Zero Zero 8,400.00
door stopper with double heavy duty rubber shoes. -
44 A003.07.13 Approved quality 75mm long aluminium toilet door latch with vacant/occupied Unit 17.00 350.00 Three Five Zero 5,950.00
indicator. -
45 A003.07.14 Approved quality chromium plated brass coat and hat hook fixed with chromium Unit 17.00 210.00 Two One Zero 3,570.00
plated brass screws. -
46 A003.08.00 Providing and fixing minimum 12mm thick X 50mm wide teak wood Architrave RM 85.00 100.00 One Zero Zero 8,500.00
(moulding) of approved design along frames etc. including lacquer polishing/ painting
matching with adjoining wood work.
-
47 A004.00.00 STEEL/ ALUMINIUM/ GLAZED/ FULLY GLASS/ PVC ETC. DOORS, WINDOWS
AND VENTILATORS
-
48 A004.05.00 Supplying and fixing M.S. rolling shutters, conforming to IS : 6248 including providing
all accessories like shutter (constructed with inter locking lath sections formed out of
cold rolled steel strips 0.9mm thick, 80mm wide and 1.25mm thick, 80mm wide
respectively for shutter width upto 3.5M and above 3.5M), jointless M.S. channel
section for guide (min. 3.15mm thick), M.S. girders, pressed bottom rails, shutter
suspension stud shaft with pully and cage, top rolling springs, locking arrangement
etc. as per approved manufacturers drawings including painting with two coats
approved make & shade and synthetic enamel paint over a coat of approved quality
red oxide zinc chromate primer, making good of all damaged surfaces etc. all
complete. -
49 A004.05.09 Motor operated rolling shutter as per approved Manufacturer's design & drawing for Sq.M. 250.00 7,160.00 Seven One Six Zero 1,790,000.00
rolling shutters for width upto 3.5 metre with all necessary electricals like motor,
switching panels, switches, cables, wires etc. as required for smooth functioning of
the shutter -
50 A004.05.10 Motor operated rolling shutter as per approved Manufacturer's design & drawing for Sq.M. 10.00 7,300.00 Seven Three Zero Zero 73,000.00
rolling shutters for width beyond 3.5 metre with all necessary electricals like motor,
switching panels, switches, cables, wires etc. as required for smooth functioning of
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 30 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

the shutter -
51 A004.05.11 Motor operated rolling shutter as per approved Manufacturer's design & drawing for Sq.M. 100.00 7,400.00 Seven Four Zero Zero 740,000.00
rolling shutters for width upto 3.5 metre with MS grill (in place of interlocked lath
sections), all necessary electricals like motor, switching panels, switches, cables,
wires etc. as required for smooth functioning of the shutter -
52 A004.10.00 Providing & applying translucent cast vinyl self adhesive washable type film with Sq.M. 225.00 1,590.00 One Five Nine Zero 357,750.00
sandblasting effect (of '3M(TM) Scotchcal(TM) Frosted Crystal 7725-324' or approved
equivalent) and of approved graphic design (electronic/ computer plotted & cut)
having durability of 10-15 years, over glass surface in doors/ windows/ partitions etc.
including preparation of base surface, cleaning, finishing etc. all complete.
-
53 A004.12.00 Providing and fixing pressed steel sheet door shutter made of 18 SWG galvanized
pressed steel sheet bent to form hollow box of 40 mm overall thickness; and
consisting of/ including:
(i) 3 mm thick MS flat all along perimeter
(ii) Packing the shutter with mineral wool (48 kg/cum) without gap
(iii) Strengthening with 18 SWG GI vertical stiffeners @200 c/c
(iv) 3 mm thick MS pad plates welded inside at required locations for fixing of
hardware etc.
(v) Fixing to door frame by 100 mm long SS 304 grade heavy duty ball bearing hinge
@600 c/c maximum
(vi) Hardware and vision panel as required.
(vii) Grinding and smoothening of welding, cleaning, finishing (synthetic enamel
painting/ polyurethane (PU) coating/ electrostatic powder coating), making true
alignments and surfaces etc. all complete.
Notes:
1. Reference shall be made to EIL standard nos. 7-75-0070, 7-75-0071
Only the net shutter(s) area shall be measured for payment
-
54 A004.12.03 Single shutter painted with Electrostatic powder coating with following hardware: Sq M 55.00 6,290.00 Six Two Nine Zero 345,950.00

(i) Over head hydraulic door closer (heavy duty).

(ii) SS 304 grade 16 mm dia 250mm long aldrop on both sides of shutter.
(iii) Spring loaded heavy duty door stopper
(iv) SS 304 grade 19 mm dia.200 mm long handle on both side of shutter.
(v) 10 mm dia SS 304 tower bolt (250mm long for 2100mm height & 600mm long for
2500mm height)
-
55 A004.12.06 Double shutter painted with Electrostatic powder coating with following hardware: Sq M 192.00 6,450.00 Six Four Five Zero 1,238,400.00

(i) Over head hydraulic door closer (heavy duty).

(ii) SS 304 grade 16 mm dia 300mm long aldrop on both sides of shutter.
(iii) Spring loaded heavy duty door stopper.
(iv) SS 304 grade 19 mm dia.200 mm long handle on both side of shutter.
(v) 10 mm dia SS 304 tower bolt ( 250mm long for 2100mm height & 600mm long for
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 31 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

2500mm height)
(vi) 2mm thick 25mmx 25mm GI angles (vertical) welded to each shutter at the
meeting point of double shutter.
-
56 A004.14.00 Providing and fixing aluminium work for doors, windows, ventilators and partitions with
extruded built up standard tubular sections/ appropriate Z sections and other sections
of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of
required dia and size, including necessary filling up the gaps at junctions, i.e. at top,
bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium
sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever
required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.
brass / stainless steel screws, all complete as per architectural drawings and the
directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for
separately) :
-
57 A004.14.02 For fixed portion of aluminium doors, windows, ventilators and partitions made from Kg 3475.00 480.00 Four Eight Zero 1,668,000.00
Powder coated aluminium (minimum thickness of powder coating 50 micron) -
58 A004.14.05M01 For shutters of doors, windows & ventilators (openable type) including frame made Kg 6925.00 500.00 Five Zero Zero 3,462,500.00
from Powder coated aluminium (minimum thickness of powder coating 50 micron)
including providing and fixing hinges/ pivots and making provision for fixing of fittings
wherever required including the cost of EPDM rubber / neoprene gasket required
(Fittings shall be paid for separately) -
59 A004.14.12 Providing and fixing double action hydraulic floor spring of approved brand and Each 336.00 2,030.00 Two Zero Three Zero 682,080.00
manufacture conforming to IS : 6315, having brand logo embossed on the body /
plate with double spring mechanism and door weight upto 125 kg, for doors, including
cost of cutting floors, embedding in floors as required and making good the same
matching to the existing floor finishing and stainless steel cover plate of minimum
thickness 1.25 mm with brass pivot and single piece M.S. sheet outer box with slide
plate etc. complete as per the direction of Engineer-in-charge. -
60 A004.14.15 Providing and fixing machine moulded aluminium covering of approved pattern & Kg 275.00 500.00 Five Zero Zero 137,500.00
design, made out of machine cut Powder coated aluminium sheet, 2.5mm thick
(minimum thickness of powder coating 50 micron) and machine holed for receiving
dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on
plate in one row on one side of joint only shall be done with stainless steel dash
fasteners of 8 mm dia and 75 mm long bolt including providing aluminium washers 2
mm thick & 15 mm dia , at a staggered pitch of 200mm centre to centre including
drilling holes in the receiving surface and providing expandable plastic sleeves in
holes etc. complete as per direction of Engineer-in-charge. -
61 A004.14.16 Filling gaps of size upto 5mm depth and 5 mm width in between aluminium frame & RM 575.00 80.00 Eight Zero 46,000.00
adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod
of approved quality as per architectural drawings and direction of Engineer-in-charge
complete -
62 A004.14.25 Providing and fixing 100mm brass locks (best make of approved quality) for Each 90.00 420.00 Four Two Zero 37,800.00
aluminium doors including necessary cutting and making good etc. complete. -
63 A004.14.27 Providing and fixing Powder coated minimum thickness 50 micron aluminium round Each 150.00 480.00 Four Eight Zero 72,000.00
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 32 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

shape handle of outer dia 100 mm with SS screws etc. complete as per direction of
Engineer in-charge -
64 A004.14.30 Providing and fixing aluminium tower bolts of size 100mm x 10mm , ISI marked, Nos 90.00 290.00 Two Nine Zero 26,100.00
anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or
dyed to required colour or shade, with necessary screws etc. complete -
65 A004.14.31 Providing and fixing toughened glass panes of 6.0 mm thickness in aluminium door, Sq.M 1575.00 5,500.00 Five Five Zero Zero 8,662,500.00
window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket
etc. complete as per the architectural drawings and the directions of engineer-in-
charge. (Cost of aluminium snap beading shall be paid in basic item) -
66 A004.15.00 Providing and fixing pressed steel door and window frames of size (assorted size out
of) Overall 125mm x 60mm section, of required profile conforming to IS: 4351, made
of 16 SWG pressed steel including/ consisting of:
i)3 mm thick MS flat spacers welded to frame @ 500mm c/c and at holdfast locations.
ii)Filling the hollow frame section with concrete. iii)MS angle (20mmx20mmx3mm)
horizontal tie member below floor finish.
iv)MS holdfasts (200mmx25mmx6mm) welded to spacers.
v)Fixing to masonry (by grouting the holdfasts with M-15 grade concrete in minimum
250mm x 100mm x 100mm sized hole)/ fixing to RCC (by minimum 100mm long, 12
mm dia metallic counter sunk anchor fasteners)
vi)MS pad plates (40mm x 150mm x 3mm) & GI mortar guard welded to frame at
hinge and other hardware locations.
vii)Metering of joints between horizontal and vertical members, grinding and
smoothening of welding, cleaning of frame surface, finishing (synthetic enamel
painting/ electrostatic powder coating/ polyurethane (PU) coating), making true
alignments and surfaces etc. all complete.
Notes:
1)Reference shall be made to EIL standard nos. 7-75- 0070, 7-75-0071
2)Cumulative length of all horizontal and vertical frame members shall be measured
for payment. -
67 A004.15.05 Frames painted with Electrostatic Powder coating. - RM 340.00 1,530.00 One Five Three Zero 520,200.00
68 A004.16.00 Providing and fixing partition upto ceiling height consisting of G.I. frame and required
board, including providing and fixing of frame work made of special section power
pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive),
consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and
0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre
with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or
metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm
and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and
ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts
and nuts, including fixing of studs along both ends of partition fixed flush to wall with
suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm
centre to centre, and fixing of boards to both side of frame work by 25 mm long dry
wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to
centre. The boards are to be fixed to the frame work with joints staggered to avoid
through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 33 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the
studs using metal to metal flat head screws, including jointing and finishing to a flush
finish with recommended jointing compound, jointing tape, angle beads at corners (25
mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as
per manufacture¿s specification and direction of engineer in charge all complete. -
69 A004.16.01 75 mm overall thickness partition with 12.5 mm thick double skin fire rated board Sq M 150.00 1,200.00 One Two Zero Zero 180,000.00
conforming to IS: 2095: part I -
70 A005.00.00 PLASTERING & POINTING -
71 A005.01.00 Providing plain cement plaster in cement mortar (1 cement:4/6 fine sand by volume)
on masonry, PCC/ RCC including preperation of base, finishing, curing etc; also
including providing 20 gauge chicken wire mesh stretched tight at all RCC/ PCC and
masonry meeting points in 300mm wide strips (150mm on on each surface) fixed with
G.I. "U" type nails before plastering. -
72 A005.01.13 Plain cement plaster with waterproofing compound conforming to IS-2645 (CICO/ Sq.M 63515.00 260.00 Two Six Zero 16,513,900.00
approved equivalent) mixed to cement mortar @ 3% by weight, Average 18mm thick
1:6 (1 cement : 6 sand) Cement supplied by the Contractor at their cost. -
73 A005.01.15 Plain cement plaster with waterproofing compound conforming to IS-2645 (CICO/ Sq.M 20365.00 250.00 Two Five Zero 5,091,250.00
approved equivalent) mixed to cement mortar @ 3% by weight, Average 15mm thick
1:4 (1 cement : 4 sand) Cement supplied by the Contractor at their cost. -
74 A005.01.17 Plain cement plaster with waterproofing compound conforming to IS-2645 (CICO/ Sq.M 80105.00 240.00 Two Four Zero 19,225,200.00
approved equivalent) mixed to cement mortar @ 3% by weight, Average 12mm thick
1:4 (1 cement : 4 sand) Cement supplied by the Contractor at their cost. -
75 A005.01.19 Plain cement plaster with waterproofing compound conforming to IS-2645 (CICO/ Sq.M 110000.00 200.00 Two Zero Zero 22,000,000.00
approved equivalent) mixed to cement mortar @ 3% by weight. Average 6mm thick
1:4 (1 cement : 4 sand) Average 6mm thick 1:4 (1 cement : 4 sand). Cement supplied
by the Contractor at their cost. -
76 A005.04.00 Providing 20mm x 10mm Grooves in plastering in perfect straight line, plumb and RM 14500.00 50.00 Five Zero 725,000.00
uniform size throughout including finishing etc. all complete. -
77 A006.00.00 ROOFING TREATMENT -
78 A006.02.00 Providing and laying cement concrete (1 cement : 2 coarse sand : 4 aggregate) over
concrete surfaces, laid to slope at all heights including, finishing, curing, tamping etc.
all -
79 A006.02.01 Cement supplied by the Contractor at their cost. - Cu.M 3185.00 5,660.00 Five Six Six Zero 18,027,100.00
80 A006.06.00 Providing and laying Cinder Concrete (1 cement : 10 cinder of 48mm size and down
grade) in all sunk areas finished with 12mm thick plain cement plaster (1 cement : 6
coarse sand by volume) including consolidating, finishing, curing, maintaining slope
etc. all complete. -
81 A006.06.01 Cement supplied by the contractor at their cost - CUM 50.00 4,760.00 Four Seven Six Zero 238,000.00
82 A006.12.00 Providing and laying 4mm thick A.P.P (atactic polypropelene) modified reinforced
bituminous waterproofing membrane over terrace and parapet including cleaning and
preperation of the surface consisting of making good all the cracks and damages,
filling potholes/ depressions, removing weak foam concrete/ plaster and refilling with
same wherever required thus preparing smooth surface of the terrace; providing and

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 34 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

applying one coat of cold applied bitumen based primer @ 0.2 to 0.4 litre per sq. mtr.;
laying the membrane by torch welding over primer, providing 100mm overlaps and
appropriately pressing the membrane to remove any entrapped air, including fixing on
parapet after providing 10mm x 20mm continuous groove in parapet for terminating
the membrane and filling the groove with polyurethane sealant and continuing this
treatment at rain water outlet points; providing finishing protective layer of 35 mm thk.
P.C.C. (1:2:4) in panels of maximum size 1200mm x 1200mm chequered finish with
24 SWG chicken wiremesh interposed in between finished smooth with joints
between panels sealed with suitable polyurethane sealant; providing fillets of 75 mm
radius with P.C.C. (1:2:4) at junctions of horizontal and vertical surfaces finished
smooth; providing 450mm x 450mm khuras (rain water collecting pits) in 1:2:4 cement
concrete at all outlets, levelled down by min. 25mm, finishing, curing etc. all complete
as per approved manufacturer's standard specifications and recommendations. .
-
83 A006.12.01M01 Mechanicaly fastern waterprofing membrane SURAFIL from SIKA or PROFEX-ORG Sq.M 36510.00 650.00 Six Five Zero 23,731,500.00
from FOSROC.(Cement supplied by the contractor at their cost). -
84 A007.00.00 WHITEWASHING, PAINTING & POLISHING -
85 A007.03.00 Providing and applying two or more coats (to give a smooth and even shade) of Sq.M 21735.00 230.00 Two Three Zero 4,999,050.00
premium plastic emulsion paint conforming to IS:5411 of approved make and shade
including cleaning and preperation of surface consisting of application of Plaster of
Paris punning over entire surface, filling all holes and depressions with plaster of
Paris, applying a coat of cement primer, two or more coats of oil based putty (as per
manufacturer's recommendations to give a paste like putty), sandpapering etc. all
complete. -
86 A007.04.00 Providing and applying two coats of distempering of approved quality and shade
including cleaning and preparation of surfaces etc. all complete. -
87 A007.04.02 Oil bound distempering conforming to IS : 428 including preparation of surfaces Sq.M 110000.00 90.00 Nine Zero 9,900,000.00
(making good of uneven plaster with plaster of paris mixed with water, sand
papering), providing a priming coat of alkali resistant/ distemper primer. -
88 A007.05.00 Providing and applying two coats of synthetic enamel paint of approved make and Sq.M 100.00 130.00 One Three Zero 13,000.00
shade to give an even shade including cleaning and preparation of surfaces, providing
2 coats of primer, stopping and filling etc. complete. -
89 A007.06.00 Providing & applying 3 coats of waterproof decorative cement paint of approved make Sq.M 3850.00 110.00 One One Zero 423,500.00
and approved shade, cleaning,including preparation of surfaces, curing etc. all
complete. -
90 A007.09.00 Providing and applying textured wall coating system consisting of twin pack fine grade
silica granules/ dry flakes made of special grade of china clay/ granite type flakes of
`Heritage' or equivalent in approved shade and texture; mixed in-situ with 100%
acrylic polymer bonding agent; applied over plastered surfaces; the granules/ flakes
etc., bonding material, mixing, method of application surface preperation etc. all shall
be as per manufacturer's recommendations and specifications. -
91 A007.09.01 Providing and applying textured granular type wall coating. - Sq.M 8915.00 560.00 Five Six Zero 4,992,400.00
92 A007.09.02 Providing and applying textured flakes type wall coating. - Sq.M 1450.00 500.00 Five Zero Zero 725,000.00

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 35 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

93 A007.10.00 Providing and applying min 2 mm thick white cement and polymer based wall putty Sq.M 500.00 100.00 One Zero Zero 50,000.00
(JK Wall care/ Birla Putty/ SARA or approved equivalent) over plastered surfaces
(masonry wall/ RCC) and smoothening the surface with sand paper etc., preparation
of surface etc. all complete as per the approved manufacturer¿s recommendations
and directions of Engineer-in-charge.
-
94 A007.11.00 Providing and applying/ finishing the walls/ RCC surfaces with Premium Acrylic SQM 55000.00 170.00 One Seven Zero 9,350,000.00
smooth exterior paint with silicon additives with low VOC (Volatile Organic
Compound) content (Snowcryl-XT of 'Snowcem India Ltd. or approved equivalent) of
required shades on new work applied in two or more coats at the rate of 1.43 ltr/ 10
sq.m over and including base coat of waterproof cement paint (of Snowcem Plus or
approved equivalent) including cleaning, preparation of surfaces, curing etc. all
complete.
-
95 A008.00.00 ROOFING -
96 A008.12.00 Providing and fixing rain water pipes with M.S. holder clamps including
fixing/embedding into masonry/concrete, providing connections like shoes, vents,
specials, bends etc. fixing in perfect plumb etc. all complete. -
97 A008.12.05 110mm dia O.D. Size. exposed PVC rain water pipe jointed with bonding solution of RM 50.00 220.00 Two Two Zero 11,000.00
approved quality and make with pressure rating of 4kg/cm2 including clamps,
connections etc. all as per approved manufacturer's details. -
98 A008.12.06 160mm dia O.D. Size. exposed PVC rain water pipe jointed with bonding solution of RM 50.00 320.00 Three Two Zero 16,000.00
approved quality and make with pressure rating of 4kg/cm2 including clamps,
connections etc. all as per approved manufacturer's details. -
99 A008.12.07 110mm dia O.D. Size. embedded PVC rain water pipe jointed with bonding solution of RM 275.00 360.00 Three Six Zero 99,000.00
approved quality and make with pressure rating of 4kg/cm2 including clamps,
connections etc. all as per approved manufacturer's details. -
100 A008.12.08 160mm dia O.D. Size. embedded PVC rain water pipe jointed with bonding solution of RM 5155.00 520.00 Five Two Zero 2,680,600.00
approved quality and make with pressure rating of 4kg/cm2 including clamps,
connections etc. all as per approved manufacturer's details -
101 A008.17.00 Providing and laying in position approved quality profiled, precoated, steel sheets (for Sq.M 100.00 920.00 Nine Two Zero 92,000.00
roofing, cladding etc.) made from cold rolled high tensile Zincalume/ Galvalume Steel
of 550 MPA yield stress conforming to IS:513, IS:15961 and ASTM AS: 1397; the
substrate shall be hot dip metallic coating of aluminium- zinc alloy (150 grams per sq.
mtr. Total on both sides, coating class AZ150); the bottom unexposed surface shall
be provided with alkyd backer of minimum 5 microns over a 5 micron coat of primer;
top exposed surface shall have SDP (Super Durable Polyester) paint system
MINIMUM 20 microns in approved shade applied over 5 microns primer; overall
coated thickness of sheets not less than 0.52 mm having base metal thickness of
minimum 0.45mm (negative tolerance not acceptable), profile depth not less than
28mm and pitch of 195 to 255mm; including cutting, mitering, laps, providing cutouts
for fixing accessories, necessary fastners (approved quality anti corrosive polyester
polymer coated, rivets, nuts, bolts, self drilling screws/ fasteners with integral washers
and EPDM seals, and nylon colour caps and natural cure type joint sealants etc.) All
complete as per approved manufacturer's specifications.
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 36 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

Note: The steel sheet shall have brand marking of coated steel manufacturer (product
details, date, mfg name, etc) on back side at regular interval confirming genuinity of
the material. -
102 A008.18.00 Providing and laying in position roofing and cladding accessories like ridge piece, Sq.M 10.00 1,210.00 One Two One Zero 12,100.00
corner piece, north light curve piece, apron piece, gutter, flashing etc. fabricated out
of 0.5mm precoated Zincalume/ Galvalume Steel steel sheets of same material/
quality etc. as that of sheeting; bent and profiled to match with the roofing and
cladding, including all cutting, fabrication, rivetting, fastners etc. all complete. -
103 A009.00.00 SANITARY FITTINGS & FIXTURES -
104 A009.01.00 Providing and fixing white glazed Earthenware Orissa pan type water closet with Unit 2.00 6,000.00 Six Zero Zero Zero 12,000.00
integral footrest of 550mmx440mm size conforming to IS : 2556, Part - III including
glazed earthenware flushing cistern supported on MS brackets conforming to IS:774
of 10 litre capacity with CP brass handles,32mm dia telescopic flush pipe with fittings
& clamps,15 mm dia overflow pipe with mosquitoproof net,15mm dia PVC connection
pipe 450mm long,painting of all exposed metalic surfaces with 2 coats of approved
shade and quality synthetic enamel paint (ICI or approved equivalent) over a priming
coat of approved qualityred oxide zinc chromate, cutting walls, floors and making
good of same,finishing, soldered joints, making inlet/ outlet connections,providing
min. 150mm thick sand cushion, finishing etc. all complete. -
105 A009.02.00 Providing and fixing white glazed Earthen ware double trap, syphonic pattern wash Unit 11.00 6,500.00 Six Five Zero Zero 71,500.00
down water closet conforming to IS : 2556 Part II including white plastic solid seat and
cover conforming to IS : 2548, CP brass hinges and rubber buffers,10 litres capacity
glazed Earthenware low level cistern conforming to IS:774 with internal overflow
system & fittings,CP brass 40mm dia flush pipe,15 mm dia ,450mm long PVC
connection pipe,ball valve, painting of all exposed matalic surfaces with 2 coats of
approved shade and quality synthetic enamel paint (ICI or approved equivalent) over
a priming coat of approved quality red oxide zinc chromate, cutting walls, floors and
making good of same, making inlet and outlet connections, finishing etc. all complete.
-
106 A009.03.00 Providing and fixing white glazed ceramic, flat back half stall type Urinals of 610mm x
400mm x 380mm size conforming to IS:2556 Part-VI including automatic glazed
Earthenware cistern for every one 15mm dia CP brass cistern outlet 750mm
long,32mm dia GI waste pipe with brass union,CP brass bottle trap,CP brass
spreader,tee,distribution pipe etc.,MS brackets for cistern, painting of all exposed
mettalic surface with 2 coats of approved shade and quality synthetic enamel paint
(ICI or approved equivalent) over a priming coat of approved quality red oxide zinc
chromate, making inlet and outlet connections, fixing with C.P. brass screws, finishing
etc. all complete. -
107 A009.03.01 One urinal.(with 5 litre capacity cistern) - Unit 11.00 6,800.00 Six Eight Zero Zero 74,800.00
108 A009.05.00 Providing and fixing glazed Earthenware Hand Wash Basin with antisplash rims on 3
sides, of 550mm x 400mm size conforming to IS : 2556 Part-IV, including approved
M.S./C.I. brackets conforming to IS : 775, one 15mm dia CP brass pillar cock, rubber
plug with CP brass chain,32mm CP Waste fitting of standard pattern pipe with 32mm
dia GI pipe, C.P. brass bottle trap, cutting walls, floors and making good the same,

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 37 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

painting all exposed metallic surfaces with 2 coats of approved shade and quality
synthetic enamel paint (ICI or approved equivalent) over an approved quality priming
coat of red oxide zinc chromate making all connections, finishing etc. all complete. -
109 A009.05.01 Providing Handwash basin of white glazed earthen-ware. - Unit 12.00 3,820.00 Three Eight Two Zero 45,840.00
110 A009.08.00 Providing and fixing 600mm x 120mm x 4mm thick Glass shelf of approved quality Unit 33.00 1,420.00 One Four Two Zero 46,860.00
with CP brass bracket and guard rails including fixing to wall with wooden cleats and
CP brass screws, cutting walls and making good the same, finishing etc.all complete.
-
111 A009.09.00 Providing and fixing approved quality chromium plated brass towel rail of 20mm dia, Unit 4.00 500.00 Five Zero Zero 2,000.00
600mm length and 1.25mm thickness including fixing to wall with wooden cleats and
CP brass screws, cutting walls and making good the same, finishing etc. all complete.
-
112 A009.10.00 Providing and fixing approved quality chromium plated liquid soap container including Unit 41.00 780.00 Seven Eight Zero 31,980.00
fixing to wall with wooden cleats and CP brass screws, cutting walls and making good
the same,finishing etc. all complete. -
113 A009.11.00 Providing and fixing Heavy grade Bib cocks/ stop cocks of spring loaded self closing
type conforming to IS : 781 including making connections, cutting walls and making
good the same etc. all complete. -
114 A009.11.01 15mm dia CP Brass stop cock. - Unit 176.00 650.00 Six Five Zero 114,400.00
115 A009.11.02 15mm dia CP Brass bib cock. - Unit 117.00 650.00 Six Five Zero 76,050.00
116 A009.13.00 Providing and fixing CP brass shower rose conforming to IS-2064: -
117 A009.13.01 100mm dia shower rose. - Unit 5.00 810.00 Eight One Zero 4,050.00
118 A009.14.00 Providing and fixing CP Brass Toilet paper holder of approved make with CP brass Unit 40.00 390.00 Three Nine Zero 15,600.00
brackets including fixing to wall with wooden cleats, CP brass screws,cutting walls
and making good the same, finishing etc. all complete. -
119 A009.15.00 Providing and fixing in position round/ oval shaped counter Hand Wash Basin with
anti-splash rims, conforming to IS:2556 Part IV, to fit in exactly and neatly in the
cutout in the marble/ granite stone finished R.C.C counter; one 15mm dia CP brass
pillar cock, rubber plug with C.P. brass chain, 32mm C.P. waste fitting of standard
pattern type with 32mm dia G.I. pipe, C.P. brass bottle trap, cutting walls, counter etc.
and making good the same, also including providing cut out in marble/ granite slab
counter top (and R.C.C underneath) of exact size and shape for wash basin to fit in
neatly and perfectly; making all connections, finishing etc. all complete. (Marble/
Granite counter top shall be paid seperately under relevant item of `Floor Finishing')
-
120 A009.15.01 Providing round/ oval shaped counter Wash Basin of glazed chinaware in White Nos. 21.00 7,250.00 Seven Two Five Zero 152,250.00
colour. -
121 A009.16.00 Providing and fixing stainless steel Kitchen/ Laboratory sink of approx. Size 610mm x Nos. 26.00 5,700.00 Five Seven Zero Zero 148,200.00
450mm x 200mm made of min. 1mm thick stainless steel sheet of `Salem Steel' or
equivalent supported on and including M.S. brackets conforming to IS: 775; one
15mm dia C.P brass long body bib cock (if fixed to wall) or swivel type pillar cock (if
fixed to counter), 15mm dia PVC/ G.I. connections to floor trap with unions etc.;
painting all exposed metallic surfaces with min. 2 coats of synthetic enamel paint of
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 38 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

approved make and shade over acoat of red oxide zinc chromate primer; cutting floor,
walls, counter etc. and making good the same, making all connections, finishing etc.
all complete. -
122 A009.17.00 Providing and fixing minimum 17mm thick polished granite stone partitions (in Sq.M 9.00 4,450.00 Four Four Five Zero 40,050.00
approved quality, shade and design/ shape) with round edges for urinals including
cutting walls, inserting (up to 100mm depth) and fixing the slab with Cement Mortar (1
cement : 3 coarse sand by volume), making good of all damaged work, finishing etc.
all complete -
123 A009.18.00 Providing and fixing round edged mirror of 6mm thick float glass with 6mm thick Sq.M 29.00 1,280.00 One Two Eight Zero 37,120.00
waterproof marine ply backing and rounded/ beveled edging, fixed on wall with
wooden cleats and CP brass screws including cutting walls/ tiles, making good the
same, finishing etc. all complete. -
124 A009.19.00 Providing and fixing CP Brass hand shower (health Faucet, of Jaquar or approved NOS 40.00 1,890.00 One Eight Nine Zero 75,600.00
equivalent ) with 8 mm Dia, 1 metre long PVC Tube and Wall hook in approved colour
and finish with all necessary fittings etc. all complete.
-
125 A009.20.00 Providing and fixing approved quality chromium plated brass towel ring of 150mm dia NOS 35.00 950.00 Nine Five Zero 33,250.00
including fixing to wall with wooden cleats and CP brass screws, cutting walls and
making good the same, finishing etc. all complete.
-
126 A009.22.00 Providing and fixing approved quality chromium plated brass Soap dish of 100mm NOS 46.00 860.00 Eight Six Zero 39,560.00
width and 130mm length including fixing to wall with wooden cleats and CP brass
screws, cutting walls and making good the same, finishing etc. all complete.
-
127 A009.23.00 Providing and fixing white glazed Earthen ware double trap, syphonic pattern wall Unit 29.00 14,180.00 One Four One Eight 411,220.00
mounted (European type) water closet conforming to IS: 2556 Part II including white Zero
plastic solid seat and cover conforming to IS : 2548, CP brass hinges and rubber
buffers, CP brass 40mm dia flush pipe,15 mm dia, ball valve, painting of all exposed
metalic surfaces with 2 coats of approved shade and quality synthetic enamel paint
(ICI or approved equivalent) over a priming coat of approved quality red oxide zinc
chromate, cutting walls, floors and making good of same, making inlet and outlet
connections, finishing etc. all complete.
-
128 A009.24.00 Providing and fixing white glazed ceramic, flat back half stall type Urinals of 610mm x Unit 21.00 18,900.00 One Eight Nine Zero Zero 396,900.00
400mm x 380mm size conforming to IS:2556 Part-VI, having electronic, battery
operated sensor based flushing system of approved make and model including
32mm dia GI waste pipe with brass union, CP brass bottle trap, CP brass spreader,
tee, distribution pipe etc., painting of all exposed metallic surface with 2 coats of
approved shade and quality synthetic enamel paint (ICI or approved equivalent) over
a priming coat of approved quality red oxide zinc chromate, making inlet and outlet
connections, fixing with C.P. brass screws, finishing etc. all complete.
-
129 A009.25.00 Providing, fixing, testing and commissioning C.P. brass 2 way bib cock quarter turn NOS 40.00 850.00 Eight Five Zero 34,000.00
type for health faucet of following make or approved equivalent 15 mm nominal bore,
all complete as per standard design, specifications and direction of Engineer-in-
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 39 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

charge. -
130 A010.00.00 FALSE CEILING, FALSE FLOORING, UNDERDECK INSULATION, PARTITIONING
-
131 A010.01.00 Providing and fixing False Ceiling grid framework for supporting ceiling tiles consisting
of main and cross runners supported from roof slab at desired height in desired
pattern including finishing, making the frame work perfectly levelled and aligned etc.
all complete. -
132 A010.01.02 GI grid framework consisting of wall channels (made of 0.5mm thick GI, 27mm size Sq.M 2500.00 1,160.00 One One Six Zero 2,900,000.00
having one flange 20mm and the other 30mm fixed to the peripherial wall @ 450mm
c/c with rawl plugs/dash fasteners), main runners (channel shaped, made of 0.9mm
thick GI, of 45mm size with two flanges of 15mm each), cross runners (channel
shaped, made of 0.5mm thick GI. of 51.1mm size having two flanges of 26mm each
with lips of 10.5mm) including suspending main runners @ 1200mm c/c max. by
means of 25mm x 0.5mm GI hangers bolted to runner and GI cleat (fixed to roof slab
with dash fasteners) @ 1200mm c/c (max), fixing the cross runners to the main
runner @ 450mm c/c with the help of connection clips and 12.5mm dia drywall screws
@ 230mm c/c to form a grid work of 450mm x 1200mm size (max) etc. all complete.
-
133 A010.02.00 Providing and fixing false ceiling tiles over false ceiling grid framework by means of
hold down clips (at four corners of each tile and one in centre of each side) as per
desired pattern at desired height, including providing necessary cut- outs for electrical
/A.C./Fire fighting fixture, making the false ceiling perfectly levelled and aligned etc.
all complete. -
134 A010.02.03 12.5mm thick false ceiling tiles made of Gypsum board conforming to IS : 2095, Sq.M 2500.00 960.00 Nine Six Zero 2,400,000.00
having thermal resistance of 0.08Sq.M K/W categorised as Class-1 when tested to
BS 476: Part-7, painted with approved shade plastic emulsion paint conforming to IS
:5411 and screw fixed to the under size of false ceiling grid work with 12.5mm dia dry
wall screw @ 230mm c/c including finishing the joints in the board flush with fillers
and tape etc. as per manufacturer's spec. to give a smooth. seamless ceiling etc. all
complete. -
135 A010.03.00 Providing and fixing Mineral Fibre Tile false ceiling consisting of A. 600mm x 600mm
x 15mm thick Mineral Fibre Acoustical tiles with durable tegular edging having noise
reduction coefficient (NRC) value of min. 0.50, light reflectance value of min.
80%,thermal conductivity (K) value of 0.052-0.057 w/m deg.C and fire performance
conforming to class-I as per BS-476,back of the tiles being provided with one coat of
protective coating. B. Suspension system consisting of hot dipped galvanised steel
main runners @ max. 1200mm c/c ( 0.33mm thk.,"T"shaped, 24mm x 38mm size with
single rotary stiching), cross runners ( 0.25mm thk.,"T" shaped with double rotary
stiching, 24mm x 30mm size, 1200mm long and 24mm x 25mm size, 600mm long ),
perimeter sections ( 0.45mm thick,22mm x 22mm size) including suspending the
system by means of 4mm dia MS wire,6mm thk. MS cleat of 25mm x 25mm size,
dash fasteners and level adjustors, providing 30 micron powder coating to exposed
metallic members, providing slit openings for fixing supply/return air grill, lighting
fixtures, AC ducts etc. all complete. -

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 40 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

136 A010.03.02 With fine granulated surface tiles (Acoustical punchers (10mm deep) = 24000sm) - Sq.M 3780.00 1,420.00 One Four Two Zero 5,367,600.00
137 A010.09.00 Providing and fixing Tray type Aluminium plank false ceiling consisting of 254/305mm Sq.M 23065.00 2,610.00 Two Six One Zero 60,199,650.00
x 1264mm or 600mm x 600mm size Aluminium planks (profiled for positive
engagement into clip-in profiles and demounting of individual planks) manufactured
out of 0.7mm thk. Aluminium alloy 3105/3005/5052 (as per ASTM 209M) with stove
enamelled (coil coated) finish in approved colour and suspension system consisting
of 0.5mm thk. 40mm x 20mm galvanised steel clip-in main runner profiles (@
1264mm or 600mm as per plank size) supported by and including 0.5mm thk. 25mm
x 16mm GI suspension angle,1mm thk. 25mm x 34mm x 76mm CRCA zinc plated
steel ceiling brackets (@ max. 1264mm c/c or 600mm as per profile) fixed to roof
slab/beam,0.5mm thk. 40mm wide, 105mm high G.I. hold on clamps slotted for level
adjustment, perimeter angles including providing slit openings for fixing supply/return
air grill, lighting fixtures, AC ducts etc. all complete. .
-
138 A010.12.00 Providing and fixing in position underdeck insulation consisting of rigid Sq.M 35000.00 1,020.00 One Zero Two Zero 35,700,000.00
Polyisocyanurate foam (PIR) slabs of size 1000 x 500mm and thickness of 30mm
(covered on one side with glass fibre tissue/ Aluminium foil having 50mm overlap)
conforming to IS:12436 having density not less than 32 kg./ Cu. M., thermal
conductivity (K- value) not more than 0.023 w/mk measured at 10 deg. C; classified
as 'Class I' for surface spread of flame as per BS 476, part 7; fixed to R.C.C. slab by
hot blow grade bitumen of 85/25 grade or cold adhesive CPRX applied over a coat of
bituminous primer @ 0.5 Litres/ Sq.M. applied to bare R.C.C. surface and to the two
surface of each PIR panel and pressed in position (while the bitumen is still tacky)
with the help of G.I. screws (No. 8 x 75mm long) fixed into rawl plugs (holes in R.C.C.
for the rawl plugs shall be drilled prior to applying coat of bituminous primer) of size 8
x 25mm inserted (5 nos. for each slab- One each at 4 corners and one at center) and
G.I washers 25mm dia; including covering the overlaps with approved quality sealing
compound (MAS-94 or equivalent); chicken wire mesh 24G x 19mm shall then be
fixed to G.I screws and tightened with lacing wire; including preparation of surface
consisting of cleaning R.C.C surface of all dust, dirt and loose particles by wire
brushing; etc. all complete as per approved manufacturer's standard specifications
and recommendations. -
139 A010.15.00 Providing and installing/ fixing in position 600mm-1000mm high truly levelled and
aligned cavity/ false flooring system having load bearing capacity of uniformly
distributed load of minimum 2025 kg/ sq.m. and point load of 675 Kg., the system
consisting of:
(i) Sub-structure/ pedestal assembly (designed for speedy assembly/ removal for
relocation/ maintenance) of zinc electro plated steel comprising of:
a. 90mm x 90mm x 4mm embossed pedestal head attachment mechanically riveted
to a 90mm long, minimum 19mm dia threaded bright M.S. rod stud with check nuts
for level adjustment (for upto 25mm) and arresting vertical movement, anti-vibrational
PVC cap (for panel and stringer location),
b. CRCA (Electrical resistant welded) Pedestal of 32mm dia (OD), 2mm thick pipe
mechanically reduced to four ribs at top to accommodate head assembly,
mechanically locked to maintain true plumb welded to pedestal base plate.
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 41 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

c. Pedestal Base plate 150mm x 150mm x 4mm thick (with stiffening folds) fixed/
anchored to main concrete floor @ 600mm c/c both ways (for installing flooring tiles)
by means of adhesive or fastener as recommended by Manufacturer.
(ii) Stringers of minimum sectional size 20mm x 32mm x 1.2mm made of hot dip
galvanized steel cold rolled construction with ribs embossed on 3 sides (designed for
strength, lateral stability, rolling loads and to support panels on all four sides for
alignment), having counter sunk holes at both ends for fixing to pedestal head
assembly with M6 machine screws.
(iii) Removable and re-usable Floor panels of size 600mm x 600mm made of all steel
welded construction (cleaned, degreased and phosphated with 11 tank process,
finished with 40-60 micron epoxy coating (and, heated to achieve adhesion to the
panel surface and corrosion resistance) with bottom surface consisting of multiple
hemispherical and reverse cones and top plain sheet (fuse welded at 129 locations)
to form an enclosed panel of an overall depth 37mm; the inner empty core of the
panel injected with light weight fire retardant, non-combustible cementitious
compound (at high pressure to fill all crevices of the panel), each panel finished on
top with 2mm thick fire retardant floor grade high pressure laminate/ 2mm thick anti-
static PVC tiles in approved design/ shade/ texture; fixed to flooring panel by means
of approved adhesive; the edges of the finished panels provided with conductive PVC
edge trim 5mm wide on all sides (mechanically locked and sealed in place).
The item includes:
i) Providing and fixing all accessories like screws, bolts, adhesive etc. as per
manufacturer's specifications.
ii) Making necessary adjustment in grid dimensions, stringer lengths, floor panel
dimensions etc. at ends or centre (to cater to specific room sizes) or at panels
locations, as required.
iii) Cutting of floor panels as required at ends.
iv) Treating the underneath cement concrete floor with one component polyurethane
floor coating etc. all complete.
v) Providing additional steel structural supports/ pedestal assembly at edges, cut outs
etc. as required.
vi) Providing all necessary accessories such as outlet boxes, grommets, Panel lifters
(at least one for each building) as required etc. all complete. -
140 A010.15.02 False flooring panels with 2mm thick anti-static PVC tiles conforming to BS : 2050, Sq.M 1500.00 6,000.00 Six Zero Zero Zero 9,000,000.00
Table-2, IS 3461/3462 in approved design/ shade/ texture. -
141 A010.15.03 False flooring panels with minimum 10mm thick polished mirror or mat finished Sq.M 150.00 6,300.00 Six Three Zero Zero 945,000.00
vitrified tiles in approved design/ shade/ texture. -
142 A011.00.00 MISCELLANEOUS ITEMS -
143 A011.01.00 Sealing 25mm thick expansion joints with premium grade two part poly-sulphide RM 1000.00 360.00 Three Six Zero 360,000.00
sealant (based on LP liquid sulphide) over and including primer (specially developed
for use with polysulphide sealant material and as approved) and back-up materials of
polyethylene strip or other bondbreaker (all as per manufacturer's specification),
sealant being mixed (the base and the curing agent thoroughly mixed with slow speed
electric mixer) and applied by sealant gun and `sealant application kit' including drying
of surfaces before application by wire brushing, finishing etc. all complete. -
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 42 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

144 A011.06.00 Providing and laying plinth protection with Bldg. drain as per EIL STD. No. 7-75-0065
consisting of -
145 A011.06.01 Plinth protection of PCC (1:3:6) laid over rammed earth to slope and trowel finished. Sq.M 4370.00 710.00 Seven One Zero 3,102,700.00
Cement supplied by the Contractor at their cost. -
146 A011.06.03 Building drain consisting of brick work, PCC (1:3:6) laid over rammed earth and Sq.M 2185.00 1,570.00 One Five Seven Zero 3,430,450.00
finished with 15mm thick plain cement plaster topped with neat cement finish @
2.75kg. of cement per Sq.M of area including finishing curing etc. all complete.
Cement supplied by the Contractor at their cost. -
147 A011.06.06 Extra for providing 600mm long MS grating drain cover as per EIL STD No. 7-75-0065 Unit 7000.00 1,760.00 One Seven Six Zero 12,320,000.00
made of 40mm x 6mm M.S. flat framework with 40mm x 6mm MS flats welded @
35mm c/c including providing & fixing 50mm x 50mm x 6mm M.S. angle frame fixed
to concrete portion of the drain.
-
148 A011.07.00 Providing and fixing in position 50mm dia GI pipe spouts to slope for drainage of RM 24.00 730.00 Seven Three Zero 17,520.00
canopy, chajja etc., including puncturing the masonry /RCC and grouting with M-15
grade concrete, finishing etc. all complete. -
149 A011.10.00 Providing and laying cinder concrete filling in sunk slabs of Toilets etc. consisting of -
-
150 A011.10.01 Average 18mm plain cement plaster (1 cement : 6 sand by volume) with Sq.M 285.00 210.00 Two One Zero 59,850.00
waterproofing compound conforming to IS : 2645 mixed @ 3% by weight over RCC
slab including preparing the base surface, finishing with one floating coat of neat
cement slurry @ 2.75 Kg. of cement per Sq.M of area, including curing, finishing etc.
all complete. Cement supplied by the Contractor at their cost. -
151 A011.10.03 Cinder concrete (1 cement : 10 cinder of 12mm size and down grade) over cement Cu.M 50.00 4,760.00 Four Seven Six Zero 238,000.00
plaster including consolidating, finishing, curing, maintaining slope etc. all
complete.Cement supplied by the Contractor at their cost. -
152 A011.15.00 Providing and fixing 2000mm high transformer gates consisting of 50mm x 50mm x Sq.M 2025.00 2,560.00 Two Five Six Zero 5,184,000.00
6mm M.S. angle frame braced with 50mm x 50mm x 6mm thick M.S. Tee stiffeners,
50mm x 50mm x 8mm gauge welded mesh fixed to the frame by 25mm x 3mm M.S.
flat beading including fixing the gate to masonry/RCC by M.S. hinge arrangement
(65mm x 65mmx 6mm M.S. angles, bolt, washers) and M.S. hold fast grouted with M-
15 grade concrete, providing and fixing M.S. pivot arrangement, MS aldrop, M.S.
tower bolts, double coat of approved shade and make sythetic enamel paint over a
coat of approved quality red oxide zinc chromate primer, finishing etc. all complete as
per EIL-STD No. 7-75-0051, 0052 ensuring smooth operation of the gate.
-
153 A011.17.00 Providing and fixing hand railing up to 1000mm high above finished floor level over
stair and landing consisting of one 25mm square M.S. baluster embedded or fixed to
floor/steps by 6mm thk. x 20mm wide M.S. clamps anchored into floor/ steps in floor
and each step grouted with M-15 grade concrete in cut out of 50mm x 50mm x
100mm size block, teakwood moulded/ M.S. pipe handrail fixed on baluster, 40mm x
40mm x 6mm M.S. flat shoe welded at the bottom of baluster, including painting the
balusters, M.S. surfaces with double coating of approved shade and make synthetic
enamel paint over a coat of approved quality red oxide zinc chromate primer coat,
finishing etc. all complete. (Only length of top handrail shall be considered for
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 43 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

payment, not the cumulative length of individual members).

-
154 A011.17.03 32 mm dia N.B. (medium) M.S. pipe handrail welded to baluster and painted with RM 790.00 1,500.00 One Five Zero Zero 1,185,000.00
double coating of synthetic enamel paint over priming coat as per EIL STD NO. 7-75-
0036. -
155 A011.22.00 Supplying, assembling and installing 1000 mm high satin finish stainless steel (SS RM 525.00 3,500.00 Three Five Zero Zero 1,837,500.00
304 grade) tubular railing of approved design in staircases, ramps, around floor cut
outs etc. consisting of:
1. 50mm dia SS pipe top handrail
2. 32 mm dia SS pipe balusters (at every third step for staircase, @ maximum
1200mm c/c for ramp, floor cutouts)
3. 3 nos minimum 18mm dia SS pipe intermediate handrails.
Including:
1. Fixing balusters to floor with 4 nos bolts änd 8mm thick, 100mm dia SS base plate
& SS cap/collar.
2. Fixing top handrail to the balusters with 12mm dia SS bar connector & 6mm thick
SS saddle plate.
3. Fixing intermediate handrails to the balusters with 12mm dia SS bar connector.
4. All end caps, decorative caps over balustrades,necessary bending, welding,
polishing of all welded joints (Length of top handrail shall be measured for payment).
-
156 A011.25.00 Providing and fixing Toilet cubicle system of overall height of 2000mm made out of 18
and 12 mm thick compact laminated board , in select colours as per manufacturer
shade card, with 18mm thick front panels and doors with SS U-section top rail on top
side for better rigidity to be supported by adjustable SS leg 100 to 150 mm height,
12mm thick continuous divider/ intermediate panels of maximum depth 1500 mm
without any joints fixed to wall and front by using U profile, door size 600 x 1800 (for
handicap toilet 900 x 1800) with front panel cut and fixed as per the requirement,
maximum width of the front panel including door to be 1100 mm (for handicap toilet
1600mm provided with a 10 x 10mm rebate on both the sides of door and front panel
with 2mm thick silicon rubber lining pasted in the rebate for noise reduction of the
door. Each cubicle shall be equipped with the following necessary hardware:
SS316 - primary thumb turn/ indicator lock - 1no.
SS316 - Door know. Handle set - 1 no.
SS316 - Coat hoos - 1 no.
SS316 - Auto reverse hinge with cap - 3 nos.
SS316 - 150 mm height adjustable leg - 2 nos.
SS316 - l-bracket, corner fixing wherever required.
The square meter area of from panels and doorMode of measurement - Square meter
basis , front panel and door measurement will be taken from wall to wall and floor to
top rail, divider measurement to be taken from wall to front and the total height of the
divider.
-
157 A011.25.01 Area of front panels and door measured from floor to top rail - Sq M 50.00 12,000.00 One Two Zero Zero 600,000.00
Zero
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 44 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

158 A014.00.00 CLADDING,FACADES ETC. -

159 A014.02.00 Providing and fixing in position minimum 25mm thick granite stone (in dry cladding) of
uniform colour and size by means of Stainless steel clamps (of Hilti/ approved
equivalent make) of minimum weight 250 gms and of minimum 5mm thickness with
various offset lengths from 50-65mm and 80-120mm, fastening the clamps with ETA
approved universal anchors and pins etc. (of Hilti/ approved equivalent make) for
fixing/ anchoring in masonary/ RCC using sufficient number of clamps/ anchors/ pins
all as per approved manufacturer's standard details and fixing sequence/
methodology to ensure stable cladding system (with a guarantee for a time span of
not less than 15 years) including sealing the joints with polyurethane based adhesive
sealant ('SIKAFLEX 11FC of SIKA India Pvt. Ltd' or approved equivalent) and
applying one or more coats of Silicon based water repellant coat ('SIKAGUARD 703W
of SIKA India Pvt. Ltd' or approved equivalent) on front side of the stone cladding incl.
cost of scaffolding etc. complete in all respect for all heights as per the instruction of
Engineer-in-charge.
-
160 A014.02.01 Granite stone dry cladding with clamps of 304 hybrid grade (of Hilti/ approved Sq.M. 1000.00 3,840.00 Three Eight Four Zero 3,840,000.00
equivalent make).
-
161 A014.03.00 Providing, supplying and installing at site Glass Reinforced Concrete (GRC) Sq.M. 100.00 4,440.00 Four Four Four Zero 444,000.00
Claddings, made up of mainly White Cement (conforming to ASTM C 150), High
Silica sand (conforming to ASTM c144), AR Glassfibre, Admixtuers (conforming to
ASTM c260,ASTM c618), by using Spray Process and as recommended by PCI
(Precast Institute) USA, Manual 128 (edn4) or as per GRCA International
specifications with design as per details provided in drawings and site requirements/
measurements and as per approved finish and color shade, with sealers and
hardwares required, all in accordance with the manufacturer's specifications and
conforming to Indian/ ASTM standards, along with submission of shop drawings for
approval, complete in all respects.
-
162 A014.04.00 Providing, supplying and installing at site Glass Reinforced Concrete (GRC) Jallis Sq.M. 50.00 4,600.00 Four Six Zero Zero 230,000.00
(Grills), made up of mainly White Cement (conforming to ASTM C 150), High Silica
sand (conforming to ASTM c144), AR Glasfibre, Admixtuers (conforming to ASTM
c260,ASTM c618), by using Vibration Cast Premix Process and as recommended by
PCI (Precast Institute) USA, Manual 128 (edn4) or as per GRCA International
specifications with design as per details provided in drawings and site requirements/
measurements and as per approved finish and color shade, with sealers and
hardwares required, all in accordance with the manufacturer's specifications and
conforming to Indian/ ASTM standards, along with submission of shop drawings for
approval, complete in all respects.
-
163 A014.05.00 Designing, engineering, providing and fixing in position fully sealed and air, water and Sq.M. 50.00 5,460.00 Five Four Six Zero 273,000.00
weather tight structural glazing system comprising of framing system (mullions,
transoms etc.) made from extruded, powder coated (min. 30 microns in approved
colour) aluminium alloy HE9WP (conforming to IS:733) of commercial quality, free
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 45 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

from all defects/ impairing appearance especially selected to fulfil the design
requirements spelt out in the specifications; machine cut glass infill panels (of size as
per the design) made of minimum 6mm thick hard coated (Glaverbel Stopsol or
approved equivalent in approved shade) reflective toughened glass, the glazed
framing panel formed by means of special structural quality silicone adhesive sealant
applied on all four sides (between glazing panel unit and aluminium alloy framing
system) and fixed to framing system. The item includes fixing the framing system to
the RCC framed structure/ masonry walls by providing and fixing necessary
Aluminium brackets (with flexible joints); with other fastening devices like bolts,
anchors, etc. (made from Stainless Steel grade 316, rivets and pins of aluminium
alloy of appropriate grade as required) self locking type and torque tightening type;
also including providing smooth membrane of Teflon (Min. 1.0 mm thickness),
providing (at all joints of the framing, glazed panels as well as joints between
aluminium frame with concrete and/ or masonry) of adhesive silicon sealant and
superior quality approved make EDPM gaskets, cleaning etc. all complete.
-
164 A014.06.00 Providing and erecting/ fixing/ installing in position aluminium composite panels Sq.M. 100.00 3,460.00 Three Four Six Zero 346,000.00
system (for external application) of 'Alucobond'/ 'Eurobond'/ 'Reynobond' or approved
equivalent comprising of aluminium framework consisting of 40mm x 40mm x 4mm
thick x 100mm long aluminium angle cleats (bracket) suitably spaced and placed to
comply to design/ elevation/ colour pattern etc. and fixed to masonry/ RCC column/
beam of the building by means of M8 x 65mm long G.I Anchor bolts, aluminium
continuous vertical angle 40mm x 40mm x 4mm fixed/ bolted to angle cleats by
means of M8 x 25mm long nut and bolt arrangement, suitable horizontal aluminium
angle horizontal members as required; cladding panels 4mm thick (overall thickness)
made of high quality extrusion grade LDPE/ LLDPE core material (3mm thick)
sandwiched between 0.5mm thick aluminium foil (on either side) made of aluminium
alloy 1100-H18 or approved equivalent and finished with minimum 35 micron (5
micron primer and 25 micron top coat) thermoplastic PVDF layer 'Kynar 500'
(minimum 70%) and polyester coating in approved shade; all complete including
providing approved silicon sealant at all joints, necessary accessories like backing
rods, aluminium pop rivets, bolts, screws, corner pieces etc. as required for the
completion of the work as per the approved manufacturer's specifications and
recommendations, cleaning, finishing etc., all complete. -
165 A016.03.00 Providing and fixing 2 hours fire rated, fully glazed, single shutter doors consisting of Sq M 60.00 42,310.00 Four Two Three One 2,538,600.00
steel door frame, shutter including stiles, rails, insulation, transparent glass, sealant Zero
and hardware such as hinges, panic bar, locks/ trims for panic bar, door closer, door
stopper, concealed flush bolt including fixing with masonry, partition etc. all complete
as per Specification and approved Manufacturer's details.
-
166 A016.04.00 Providing and fixing 2 hours fire rated, fully glazed, double shutter doors consisting of Sq M 365.00 43,910.00 Four Three Nine One 16,027,150.00
steel door frame, shutter including stiles, rails, insulation, transparent glass, sealant Zero
and hardware such as hinges, panic bar, locks/ trims for panic bar, door closer, door
stopper, concealed flush bolt including fixing with masonry, partition etc. all complete
as per Specification and approved Manufacturer's details.
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 46 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

-
167 A016.07.00 Providing and fixing 2 hours fire rated, single shutter steel doors consisting of steel Sq M 180.00 12,870.00 One Two Eight Seven 2,316,600.00
door frame, shutter, vision panel, insulation and hardware such as hinges, panic bar, Zero
locks/ trims for panic bar, door closer, door stopper, concealed flush bolt etc.
including fixing with masonry, partition etc. all complete as per specification and
approved Manufacturer's details.
-
168 A016.08.00 Providing and fixing 2 hours fire rated, double shutter steel doors consisting of steel Sq M 70.00 14,260.00 One Four Two Six Zero 998,200.00
door frame, shutter, vision panel, insulation and hardware such as hinges hinges,
panic bar, locks/ trims for panic bar, door closer, door stopper, concealed flush bolt
including fixing with masonry, partition etc. all complete as per specification and
approved Manufacturer's details.
-
169 A016.09.00 Providing and fixing 2 hours fire rated, glazed partition of desired design consisting of Sq M 185.00 23,500.00 Two Three Five Zero 4,347,500.00
steel frame, insulation and transparent glass and glazing beading, matrix mineral Zero
boards, intumescent putty, fire resistant acrylic sealant etc. all complete including
preparing fabrication/ installation drawings including fixing with masonry, partition etc.
all complete as per specification and approved Manufacturer's details.
-
170 A998.00.00 Miscellaneous -
171 A998.99.00 Miscellaneous -
172 A998.99.99V01 Providing Gypsum board false ceiling of desired design, and finish consisting of : SQM 500.00 1,400.00 One Four Zero Zero 700,000.00
i. "Gypsteel ULTRA" or approved equivalent false ceiling frame system including CRP
surface ribbed components such as ceiling sections (0.5mm thick, 80mm wide, @
maximum 457mm c/c, fixed to intermediate channels with connecting clip),
Intermediate channels (0.9mm thick, 45mm wide, @ maximum 1220mm c/c,
suspended from the soffit with ceiling angles (25x10x 0.55mm @ 900mm c/c
maximum, GI cleat and steel fasteners), perimeter
channels (0.5mm thick, 27mm wide, screw fixed to wall/partition at 610mm c/c),
including all fasteners, angles, connectors, clips etc. all complete ii. Single layer of
12.5mm tapered edge plain gypsum
board, screw fixed to ceiling sections with 25mm drywall screws @ 230mm c/c.
Including jointing and finishing the boards for flush surface including filling and
finishing with approved (as/ Manufacturer's recommendation) jointing compound,
paper tape, finishing gap between wall and ceiling with POP, wire mesh , two coats of
drywall top coat, providing necessary cut outs and finishing for electrical/ AC/ Other
fittings, fixtures, providing vertical ceiling boards, necessary additional framing
components for cutouts/ vertical surface etc, all complete for all heights.

Note: Actual surface area (including vertical ceiling board area if

any between false ceilings at various levels, excluding areas for cut-outs, openings
etc.) of false ceiling shall be measured for payment -
173 A998.99.99V02 Refer item no: A998.99.99V01 SQM 100.00 1,540.00 One Five Four Zero 154,000.00
Providing Gypsum board curved false ceiling of desired design, shape, curve and
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 47 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

finish in place of flat false ceiling including necessary bending of framing components,
providing ceiling boards in desired shape/ curve

Note:Actual surface area (including vertical ceiling board area if

any between false ceilings at various levels, excluding areas for cut-outs, openings
etc.) of false ceiling shall be measured for payment -
174 A998.99.99V03 Refer item no: A998.99.99V01 SQM 250.00 2,500.00 Two Five Zero Zero 625,000.00
Extra for providing gypsum board coffers of desired design, shape, curve etc.
including framing members, false ceiling boards (horizontal/ curved/ vertical) etc. all
complete.

Note:Plan area of coffered portion shall be measured for

payment.
-
175 A998.99.99V04 Refer Item no: A998.99.99V01 SQM 250.00 1,680.00 One Six Eight Zero 420,000.00
Extra for providing approved design/ shape coves in false ceiling/ false ceiling coffers
with gypsum board, plaster of paris, including framing members, wire mesh, finishing
etc. all complete.
-
176 A998.99.99V05 Refer Item No. A014.02.01 RM 500.00 250.00 Two Five Zero 125,000.00
Providing and fixing 25mm wide Stainless Steel (grade-
304) strip in horizontal/ vertical joints of stone cladding
fixed with approved adhesive including making grooves in
joints, finishing etc. all complete for all heights. -
177 A998.99.99V06 Providing and fixing in position Pantry/Kitchen overhead cabinets (up to 300 mm SQM 50.00 5,000.00 Five Zero Zero Zero 250,000.00
deep) made of 18mm thick waterproof commercial block board sides, shelves, top,
bottom etc., 6mm thick waterproof commercial ply backing, 18mm thick waterproof
commercial block board shutters finished with 1 mm thick decorative laminate in
approved texture, design and pattern, including providing 6mm thick mahogany wood
lipping/ edging to all exposed edges of the commercial board, painting with two or
more coats of synthetic enamel paint in approved make and shade over a coat of
approved wood primer to all interior portions of the cabinets, continuous hinges,
lacquered french polishing the Mahogany wood lipping/ edging, finishing etc.
(Note- only front area shall be measured for the purpose of payment.) -
178 A998.99.99V07 Providing and fixing Gypsum board & GI frame partition upto overall 200mm SQM 60.00 6,800.00 Six Eight Zero Zero 408,000.00
thickness, up to 6000 high for video wall/ giant screen consisting of
i. Framework of "Gypsteel ULTRA" or approved equivalent system including CRP
surface ribbed components such as pair of (on both sides of partition, connected to
each other) vertical studs (70x34x36mm, 0.5mm thick, @ maximum 600mm c/c), pair
of floor/ ceiling channels (0.5mm thick, 72x32x32mm at floor, ceiling and at
intermediate heights,), fixing channels (0.91mm thick, 99x12.5x12.5 at intermediate
heights to connect pair of studs), Perimeter channels, fixing channels, fixing with floor/
wall/ ceiling, jointing all components, including all fasteners, angles, connectors, clips,
providing curves as/ design etc. all complete.
ii. Single layer of 12.5mm tapered edge plain gypsum board on both sides of partition
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 48 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

screw fixed to frame work with 25mm drywall screws @230mm c/c. Including jointing
and finishing the boards for flush/ curved surface including filling and finishing with
approved (as/ Manufacturer's recommendation) jointing compound,
paper tape, finishing gap between wall and ceiling with POP, wire mesh and two coats
of drywall top coat, providing necessary curves / corbelling as/ design, providing
necessary cut outs and finishing for electrical/ AC/ Video wall/Doors/other fittings,
providing corner beads, providing gypsum boards around the perimeter of cut outs/
openings, providing timber sections in the studs to hold door frames etc. fixtures,
finishing etc, all complete for all heights as/ per approved manufacturer's details and
specifications.

Note:
Actual surface area of partition (one side only, excluding cut-out, openings for door,
video wall area, but including uncladded framework area above false ceiling level)
shall be measured for payment. -
179 A998.99.99V08 Refer Item No. A998.99.99V07. SQM 60.00 200.00 Two Zero Zero 12,000.00
Providing and fixing approved quality, 1mm thick laminate
(metal appearance and finish) over gypsum board. -
180 A998.99.99V09 Providing and fixing 2 hours fire rated, fully glazed, fixed window consisting of window SQM 20.00 30,000.00 Three Zero Zero Zero 600,000.00
frame including stiles, rails, insulation, transparent glass, sealant and hardware Zero
including fixing with masonry etc. all complete as per Specification and approved
Manufacturer's details.
-
181 A998.99.99V10 Providing and fixing in position fully glass partitioning work (up to false ceiling) of SQM 150.00 15,000.00 One Five Zero Zero Zero 2,250,000.00
12mm thick toughened float glass continuous type(as /drawing) fixed within (and
including) 100x44mm coloured anodized aluminium top runner, 150x44mm bottom
runner, 75x44mm vertical member at end fixed to RCC/Hollow concrete Block
columns/pier including fixing suitably the top runner to RCC/Structural steel members
provided for supporting the partition system)including fixing the bottom & side runners
to floor, columns, wall etc. with rowl plugs, including fixing with EPDM gaskets and
minimum 1.5mm thick Aluminium beading jointing with silicone adhesive, finishing etc
all complete as per drawing. -
182 A998.99.99V11 Providing and fixing frameless single/double piece Glass SQM 20.00 7,000.00 Seven Zero Zero Zero 140,000.00
Doors (swing shutters) in partition made of 12mm thick toughened float glass
single/double shutter with stainless steel finish patch fittings and 150mm x 44mm
extruded Aluminium frame at bottom , including all hardware such as SS patch
fittings, floor spring, pivot on top, locking arrangement , 30mm dia, 350mm long SS
pull handle etc. all complete. -
183 A998.99.99V12 Providing and fixing polished 18mm thick polished Granite stone slabs similar to SQM 10.00 4,500.00 Four Five Zero Zero 45,000.00
counter top in counter facia upto 125mm high by means of minimum 12mm thick.
cement mortar in 1:3 (1Cement: 3 Coarse sand) or adhesive as per approved
manufacturer. -
184 A998.99.99V13 Providing moulding of full round design in Granite/ marble Stone by machine cutting RM 50.00 200.00 Two Zero Zero 10,000.00
including rubbing, polishing, finishing etc. all complete. -
185 S000.00.00 CIVIL & STRUCTURAL -
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 49 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

186 S001.00.00 EARTH WORK (REFER SPECIFICATION NO. 6-68-0003) -

187 S001.01.00 Earthwork excavation in soil -
188 S001.01.01 Earth work in EXCAVATION below ground level for all kinds of works in ALL TYPES Cu.m. 46350.00 210.00 Two One Zero 9,733,500.00
OF SOILS EXCEPT SOFT ROCK AND HARD ROCK as classified in specification for
a depth upto 1.5m including removal of vegetation, shrubs and debris, cutting and
dressing of sides in slopes, levelling, grading and ramming of bottoms, dewatering of
accumulated water from any source and keeping the surface dry for subsequent
works and disposal or stacking of excavated material within a lead of 100m, as
directed including providing temporary supports to existing service lines like water
pipes, sewage pipes, electric overhead and underground cables etc. all complete, but
excluding shoring and strutting. -
189 S001.01.02 Earth work in EXCAVATION below ground level for all kinds of works in ALL TYPES Cu.m. 46350.00 260.00 Two Six Zero 12,051,000.00
OF SOILS EXCEPT SOFT ROCK AND HARD ROCK as classified in specification for
a depth beyond 1.5m and upto and inclusive of 3.0m including removal of vegetation,
shrubs and debris, cutting and dressing of sides in slopes, levelling, grading and
ramming of bottoms, dewatering of accumulated water from any source and keeping
the surface dry for subsequent works and disposal or stacking of excavated material
within a lead of 100m, as directed including providing temporary supports to existing
service lines like water pipes, sewage pipes, electric overhead and underground
cables etc. all complete, but excluding shoring and strutting. -
190 S001.01.03 Earth work in EXCAVATION below ground level for all kinds of works in ALL TYPES Cu.m. 50.00 290.00 Two Nine Zero 14,500.00
OF SOILS EXCEPT SOFT ROCK AND HARD ROCK as classified in specification for
a depth beyond 3.0m and upto & inclusive of 4.5m including removal of vegetation,
shrubs and debris, cutting and dressing of sides in slopes, levelling, grading and
ramming of bottoms, dewatering of accumulated water from any source and keeping
the surface dry for subsequent works and disposal or stacking of excavated material
within a lead of 100m, as directed including providing temporary supports to existing
service lines like water pipes, sewage pipes, electric overhead and underground
cables etc. all complete, but excluding shoring and strutting. -
191 S001.06.00 SHORING AND STRUTTING -
192 S001.06.01 Providing and installing approved type of "SHORING AND STRUTTING" by open Sq.m. 200.00 370.00 Three Seven Zero 74,000.00
timbering method for all depths to retain earth including dismantling and removal of
the same etc. from site after completion of work etc. all complete as directed. -
193 S001.06.02 Providing and installing approved type of "SHORING AND STRUTTING" by close Sq.m. 200.00 510.00 Five One Zero 102,000.00
timbering method for all depths to retain earth including dismantling and removal of
the same etc. from site after completion of work etc. all complete as directed. -
194 S001.07.00 Backfilling after exceution of work -
195 S001.07.01 BACKFILLING after execution of the WORK to proper grade and level with selected Cu.m. 48230.00 190.00 One Nine Zero 9,163,700.00
materials from available excavated soil from spoil heaps within a LEAD OF 100M,
including re- excavating the deposited soil excavated earlier, breaking clods, laying at
all depths and heights in layers of thickness not exceeding 15 Cms. watering, rolling
and ramming by manual methods/ mechanical compactors to achieve 90% laboratory
maximum dry density, dressing, trimming etc. in foundations, plinths, trenches, pits

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 50 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

etc. all complete. -

196 S001.07.02 BACKFILLING after execution of the WORK to proper grade and level with selected Cu.m. 20670.00 310.00 Three One Zero 6,407,700.00
materials from available excavated soil from spoil heaps beyond a LEAD OF 100M
AND UPTO & INCLUSIVE OF 500M including re-excavating the deposited soil
excavated earlier, breaking clods, laying at all depths and heights in layers of
thickness not exceeding 15 Cms. watering, rolling and ramming by manual
methods/mechanical compactors to achieve 90% laboratory maximum dry density,
dressing, trimming etc. in foundations, plinths, trenches, pits etc. all complete. -
197 S001.10.00 Transporting & Disposing the SURPLUS EARTH AND DEBRIS -
198 S001.10.03 Transporting and disposing the SURPLUS EARTH AND DEBRIS including shrubs Cu.m. 23850.00 270.00 Two Seven Zero 6,439,500.00
and vegetations from construction area beyond the initial LEAD OF 3.0KM AND
UPTO & INCLUSIVE OF 5.0KM including re-excavating the deposited soil excavated
earlier, transportation, loading, unloading, laying at all depths and heights, stacking,
levelling and dressing both the area (viz. from where the earth is transported and
where it is deposited) to required levels and slopes complete with all lifts as directed.
For carting on the basis of truck measurements (volume of truck reduced by 30% for
voids). -
199 S002.00.00 PLAIN & REINFORCED CEMENT CONCRETE: (REFER SPECIFICATION NO. 6-68-
0004) -
200 S002.17.00 PCC - Non FIM Items -
201 S002.17.01 Providing and laying PLAIN CEMENT CONCRETE for all depths below and upto Cu.m. 2160.00 4,800.00 Four Eight Zero Zero 10,368,000.00
plinth level in foundations,drains, fillings, non-suspended floors, pavements & ramps
or any other works etc. including shuttering, tamping, ramming, vibrating, curing etc.
all as specified in any shape, position, thickness and finishing the top surface rough
or smooth as specified and directed all complete for concrete of nominal mix 1:5:10
by mass (1 Cement: 5 Coarse Sand: 10 Crushed Stone Aggregates/Gravels) with
40mm and down size graded crushed stone aggaregates/Gravels.ALL MATERIALS
INCLUDING CEMENT SUPPLIED BY THE CONTRACTOR. -
202 S002.17.05 Providing and laying PLAIN CEMENT CONCRETE of nominal mix 1:3:6 by mass (1 Cu.m. 10.00 5,570.00 Five Five Seven Zero 55,700.00
Cement : 3 Sand : 6 Crushed Stone Aggregates) with 10mm and down size graded
crushed stone aggregates below and upto plinth level as SCREED in trenches, floor
slabs, sumps, channels, drains etc. for all depths including shuttering, tamping, curing
etc. as specified in any shape, level, thickness, position and finishing the top surface
smooth etc. all complete as directed. ALL MATERIALS INCLUDING CEMENT
SUPPLIED BY THE CONTRACTOR. -
203 S002.17.06 Providing and laying PLAIN CEMENT CONCRETE of nominal mix 1:3:6 by mass (1 Cu.m. 10.00 6,060.00 Six Zero Six Zero 60,600.00
Cement : 3 Sand : 6 Crushed Stone Aggregates) with 10mm and down size graded
crushed stone aggregates above plinth level as SCREED in floor slabs, roofs, chajjas,
canopies, gutters etc. for all heights including shuttering, tamping, curing etc. as
specified in any shape, level, thickness, position and finishing the top surface smooth
etc. all complete as directed.ALL MATERIALS INCLUDING CEMENT SUPPLIED BY
THE CONTRACTOR. -
204 S002.17.08 Providing and laying PLAIN CEMENT CONCRETE for all depths below and upto Cu.m. 25.00 6,540.00 Six Five Four Zero 163,500.00
plinth level in foundations,drains, fillings, non-suspended floors, pavements & ramps
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 51 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

or any other works etc. including shuttering, tamping, ramming, vibrating, curing, etc.
all as specified in any shape, position, thickness and finishing the top surface rough
or smooth as specified and directed all complete for concrete grade M20 with 20mm
and down size graded crushed stone aggaregates/Gravels.ALL MATERIALS
INCLUDING CEMENT SUPPLIED BY THE CONTRACTOR. -
205 S002.18.00 RCC Substrutures - Non FIM Items -
206 S002.18.17 Providing and laying REINFORCED CEMENT CONCRETE OF M-30 GRADE with 20 CUM 21630.00 6,230.00 Six Two Three Zero 134,754,900.00
mm and down size graded crushed stone aggregates/ gravel in SUB-STRUCTURE
e.g. foundations, raft, beams, slabs, pile caps, retaining walls, dyke walls, jambs,
counterforts, buttresses, pedestals, pipe sleepers, columns, suspended floors,
staircases, landings, steps, brackets etc., including equipment/ machine foundations
& pedestals viz. compressors, ID & FD fans, pumps, generators, crushers, mills, etc.,
(including single pour concreting as specified on the drawing), applying cement wash
on concrete surface (wherever no other surface application is specified), providing
pockets, openings, recesses, chamfering, etc., wherever required, vibrating, tamping,
curing and rendering if required to give a smooth and even surface etc. (EXCLUDING
THE COST OF REINFORCEMENT, SHUTTERING & SPECIFIED ADMIXTURES) for
all depths below and upto plinth level in any shape, position and thickness etc. all
complete as specified, shown and directed. ALL MATERIALS INCLUDING CEMENT
SUPPLIED BY THE CONTRACTOR. -
207 S002.18.22 Providing and laying REINFORCED CEMENT CONCRETE OF M-30 GRADE with 20 CUM 1745.00 6,350.00 Six Three Five Zero 11,080,750.00
mm and down size graded crushed stone aggregates/ gravel in SUB-STRUCTURE
e.g. trenches, culverts, manholes, pipe encasement, catchpits, drains, pits, etc.,
applying cement wash on concrete surface (wherever no other surface application is
specified), providing pockets, openings, recesses, chamfering, etc., wherever
required, vibrating, tamping, curing and rendering if required to give a smooth and
even surface etc. (EXCLUDING THE COST OF REINFORCEMENT, SHUTTERING &
SPECIFIED ADMIXTURES) for all depths below and upto plinth level in any shape,
position and thickness etc. all complete as specified, shown and directed. ALL
MATERIALS INCLUDING CEMENT SUPPLIED BY THE CONTRACTOR. -
208 S002.19.00 RCC Superstructures - Non FIM Items -
209 S002.19.17 Providing and laying REINFORCED CEMENT CONCRETE OF M-30 GRADE with 20 CUM 42000.00 6,600.00 Six Six Zero Zero 277,200,000.00
mm and down size graded crushed stone aggregates/ gravel in SUPER STRUCTURE
in suspended floors, slabs, beams, columns, walls including counterforts, staircases,
landings, steps, facias, fins, mouldings, gutters, shelves, window sills, canopies,
lintels, girders, ducts, brackets, chajjas with drip moulds, pedestals, posts, struts,
equipment/ machine foundations, ramps etc. (including single pour concreting as
specified on the drawing), providing cement wash (wherever no other surface
application is specified), providing pockets, openings, recesses, chamfering wherever
required, vibrating, tamping, curing and rendering if required to give a smooth and
even surface etc. (EXCLUDING THE COST OF REINFORCEMENT, SHUTTERING
AND SPECIFIED ADMIXTURES) FOR ALL HEIGHTS UPTO & INCLUSIVE OF 20 m
ABOVE PLINTH LEVEL in any shape, position, thickness etc. all complete as
specified, shown and directed. ALL MATERIALS INCLUDING CEMENT SUPPLIED

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 52 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

BY THE CONTRACTOR. -
210 S002.20.00 RCC Flooring - Non FIM Items -
211 S002.20.02 Providing and laying REINFORCED CEMENT CONCRETE OF M-20 GRADE with Cu.m. 8700.00 5,820.00 Five Eight Two Zero 50,634,000.00
20mm and down size graded crushed stone aggregates / gravel in NON-
SUSPENDED slabs / pavement slabs including pedestals, ramps etc. leaving
pockets, laying in alternate panels to required slopes, all necessary form work and
finishing the top surface rough or smooth, including cost of admixtures if used,
providing pockets, openings, recesses, chamfering etc., wherever required, vibrating,
tamping, curing and rendering if required to give a smooth and even surface etc.
(EXCLUDING THE COST OF REINFORCEMENT AND SHUTTERING) for all depths
below and upto plinth level in any shape, position and thickness etc. all complete as
specified, shown and directed. ALL MATERIALS INCLUDING CEMENT SUPPLIED
BY THE CONTRACTOR. -
212 S002.22.00 Precast Elements - Non FIM Items -
213 S002.22.07 Manufacturing, transporting, supplying and erecting in position Reinforced Cement CUM 670.00 13,670.00 One Three Six Seven 9,158,900.00
Concrete PRECAST ELEMENTS such as columns, beams, cover slabs, lintels, Zero
louvers, fins, shelves etc. of M-30 grade with 20mm and down size graded crushed
stone aggregates/gravel, each unit upto and inclusive of 500 kg. for all leads, levels,
shapes and thickness including all moulds, shuttering and centering, vibrating,
tamping, curing, chamfering wherever required, finishing the top surface with cement
mortar 1:3 ( 1 Cement : 3 Sand) to give a smooth and even surface, or non skid finish
as specified, providing lifting hooks, metal inserts, making holes pockets, (only M.S.
inserts to be measured & paid separately) transporting to site, erecting, levelling,
aligning and fixing in position with cement mortar 1:3 ( Cement : 3 Coarse Sand),
breaking bricks and/or concrete surfaces and making good the same etc. all complete
(excluding the Cost of Reinforcement ) and as directed. All materials including cement
supplied by the contractor. -
214 S002.23.00 HYD Bars / MS Bars - Non FIM Items -
215 S002.23.08 Supplying and placing in position HIGH YEILD-STRENGTH DEFORMED STEEL MT 12000.00 62,000.00 Six Two Zero Zero Zero 744,000,000.00
BARS REINFORCEMENT of Grade Fe500D TMT conforming to IS:1786, for RCC
work including transporting the Steel, straightening, cleaning, decoiling, cutting,
bending to required shapes and lengths as per details, binding with 18 SWG black
soft annealed binding wire at every intersection, supplying and placing with proper
cover blocks, supports, chairs, overlaps, welding, spacers, fanhooks etc. for all
heights and depths etc. all complete as directed. SUPPLY OF ALL MATERIAL IN
CONTRACTOR'S SCOPE. -
216 S002.25.00 Centering and Shuttering - Non FIM Items -
217 S002.25.01 Providing and fixing CENTERING AND SHUTTERING in foundations, footings,raft Sq.m. 70120.00 320.00 Three Two Zero 22,438,400.00
beams, slabs, pile caps, retaining walls, jambs, counter-forts, buttresses, trenches,
equipment/machine foundations, pedestals, abutments, pipe sleepers, columns,
plinth beams, lintels, suspended slabs, beams, staircases, landings, steps, non-
circular tunnels/bunkers/ silos/ shafts/ hoppers/liquid storage structures etc. for all
depths below and upto & inclusive of plinth level including shuttering for single pour
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 53 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

concreting, strutting, bracing, propping etc., keeping the same in position during
concreting and removal of the same after specified period etc. for Straight/ Inclined
Shuttering, keeping necessary provision for inserts, projecting dowels, anchor bolts or
any other fixture etc. all complete and as specified and directed. -
218 S002.25.02 Providing and fixing CENTERING AND SHUTTERING in superstrctures in retaining Sq.m. 335900.00 370.00 Three Seven Zero 124,283,000.00
walls, jambs, counter-forts, buttresses, equipment/ machine foundations,
abutments,columns, lintels, suspended slabs, beams, staircases, landings, steps,
non-circular tunnels/ bunkers/ silos/ shafts/ hoppers/ liquid storage structures etc. for
all heights above plinth level including shuttering for single pour concreting, strutting,
bracing, propping etc., keeping the same in position during concreting and removal of
the same after specified period etc. for Straight/ Inclined Shuttering, keeping
necessary provision for inserts, projecting dowels, anchor bolts or any other fixture
etc. all complete and as specified and directed. -
219 S002.25.07 Providing and fixing CENTERING AND SHUTTERING for CURVED SHUTTERING in Sq.m. 100.00 420.00 Four Two Zero 42,000.00
foundations in all types for Columns, Beams, Slabs, Walls, etc. of Buildings for all
depths below and upto & inclusive of plinth level, including strutting, bracing, propping
etc., keeping the same in position during concreting and removal of the same after
specified period etc. for Straight/ Inclined Shuttering, keeping necessary provision for
inserts, projecting dowels, anchor bolts or any other fixture etc. all complete and as
specified and directed. -
220 S002.25.08 Providing and fixing CENTERING AND SHUTTERING for CURVED SHUTTERING in Sq.m. 100.00 540.00 Five Four Zero 54,000.00
superstructures in all types for Columns, Beams, Slabs, Walls, etc. of Buildings for all
heights above plinth level, including strutting, bracing, propping etc., keeping the
same in position during concreting and removal of the same after specified period etc.
for Straight/ Inclined Shuttering, keeping necessary provision for inserts, projecting
dowels, anchor bolts or any other fixture etc. all complete and as specified and
directed. -
221 S002.26.00 Expansion joints - Non FIM Items -
222 S002.26.03 Supplying and fixing in position 50 mm (2X25 mm) thick BITUMEN IMPREGNATED Sq.m. 1850.00 1,590.00 One Five Nine Zero 2,941,500.00
FIBRE BOARD conforming to IS:1838 of approved quality in expansion joints at all
locations and levels in concrete structures etc. all complete as shown, specified and
directed. -
223 S002.26.05 Supplying and sealing EXPANSION JOINTS 50 mm wide and 12mm deep at all m 3690.00 440.00 Four Four Zero 1,623,600.00
locations and levels in Concrete Structures with approved two part liquid
POLYSULPHIDE SEALING COMPOUND as per IS:12118 including raking of joints
etc. all complete as shown, specified and directed. -
224 S003.00.00 CONCRETE FOR LIQUID RETAINING/LEAK PROOF STRUCTURES (REFER
SPECIFICATION NO.6-68-0005) -
225 S003.04.00 Water Proofing Comp. - Non FIM Items -
226 S003.04.01 Supplying and mixing of approved brand of integral WATER PROOFING Kg 100.00 100.00 One Zero Zero 10,000.00
COMPOUND in cement concrete, cement mortar etc. as per manufacturer's
specifications, to make it leak proof/water tight etc. all complete as specified and
directed. -
227 S004.00.00 STRUCTURAL STEEL WORKS (REFER SPECIFICATION NO. 6-68-0006) -

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 54 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

228 S004.03.00 General Steel Works - Non FIM Items -

229 S004.03.13 Supplying, transporting, storing, fabricating & erecting in position and testing/ MT 30.00 85,430.00 Eight Five Four Three Zero 2,562,900.00
examining bolted and/ or welded STRUCTURAL STEEL WORKS of Grade E350BR /
E350B0 (conforming to IS:2062) at all locations and levels UPTO & INCLUSIVE OF
20 m ABOVE HPP/ FGL, including all builtup sections/ compound sections made out
of rolled sections and/ or plates/ bent plates in all types of structural frameworks, floor
beams, stairs, or any other structural items or accessories to support equipments,
piping, conveyor galleries, towers, masts, etc., but excluding silos, bunkers, hoppers,
etc., cutting to required size, straightening/ bending if required, edge preparation,
cleaning, preheating, bolting/ welding of joints, (including sealing the joints of box
sections with continuous welding and plugging any open ends & holes of box
sections), finishing edges by grinding, fixing in line and level with temporary staging &
bracing and removal of the same after erection, grouting with Ordinary Grout or
premix free flow Nonshrink Grout as specified, including preparation and submission
of detailed fabrication drawings, preparing the surface for painting (SSPC-SP-10) and
applying pre-erection/ shop primer (1 coat of F-9 @ 65-75 micron DFT) as per EIL
Specification No. 6-79-0020 (or as per Job Specification, wherever applicable) after
fabrication etc., all complete. SUPPLY OF ALL MATERIAL IN CONTRACTOR'S
SCOPE. -
230 S004.04.00 Painting - Non FIM Items -
231 S004.04.08 Supplying and applying COATING (Post-erection/ Field) of approved quality and MT 30.00 9,930.00 Nine Nine Three Zero 297,900.00
shade as per Sl. No. 9.2 of Table 9.0 of EIL Specification No. 6-79-0020 (or as per
Job Specifications, wherever applicable) over the coat of shop primer already applied,
including storage, surface preparation, degreasing, cleaning, drying, providing
necessary arrangement for access, testing etc. including touching up of shop primer
coat as per Sl. No. 7.2.1 of Table 7.2 of EIL Specification No. 6-79-0020 (or as per
Job Specifications, wherever applicable), for steel structures (excluding ladders, spiral
stairways & hand rails) at all location & levels, all complete as specified, for OFFSITE
(INLAND) areas considering environment classification as INDUSTRIAL. SUPPLY OF
ALL MATERIAL IN CONTRACTOR'S SCOPE.(Unit rate based on Structural steel
weight).
-
232 S006.00.00 MISCELLANEOUS STEEL WORKS (REFER SPECIFICATIONS NO. 6-68-0008) -
233 S006.15.00 Anchor Bolts - Non FIM Items -
234 S006.15.01 Supplying, fabricating, fixing and keeping in position at all levels and locations MT 2.00 122,730.00 One Two Two Seven 245,460.00
THREADED ANCHOR BOLTS of all diameters and nomenclature including nuts, Three Zero
washers, anchor plates, pipe sleeves etc. in foundations, columns, pedestals, slabs,
beams, walls etc. or any other place as directed including handling & transporting,
straightening if required, turning from relevant size M.S. rounds to required diameter,
threading, welding, providing necessary templates and auxilliary dummy structures, if
any, necessary tying and welding with reinforcement, adjustment of shuttering &
reinforcement/any other fixture, greasing exposed metal surfaces, covering bolts and
packing the sleeves with jute cloth etc. all complete as specified and

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 55 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

directed.(SUPPLY OF ALL MATERIALS IN CONTRACTOR'S SCOPE). -

235 S006.16.00 MS Metal Inserts - Non FIM Items -
236 S006.16.01 Supplying, transporting, storing, fabricating and fixing in position M.S. METAL MT 160.00 101,100.00 One Zero One One 16,176,000.00
INSERT (with lugs) of any shape made out of flats, plates, rolled sections, pipes etc. Zero Zero
providing necessary templates, staging, cutting, straightening, if required, bolting,
welding as required and embedding in position on both Plain and Reinforced Cement
concrete members inclusive of adjusting shuttering & reinforcement/ any other fixture,
welding where necessary, tying and holding to correct level, line and position, any
auxiliary dummy structures to support the heavy inserts, painting exposed surfaces
with a coat of primer as per EIL Specification No. 6-79-0020 (or as per Job
Specification wherever applicable), etc. all complete for all depths and heights as
specified and directed. (SUPPLY OF ALL MATERIALS IN CONTRACTOR'S
SCOPE). -
237 S006.17.00 GI Pipe Sleeves - Non FIM Items -
238 S006.17.01 Supplying, fabricating and fixing in position G.I. PIPE SLEEVES of all diameters MT 25.00 115,580.00 One One Five Five 2,889,500.00
including providing necessary staging, cutting, straightening if required, bolting, Eight Zero
welding as required and embedding in position on both Plain and Reinforced Cement
concrete members inclusive of adjusting shuttering & reinforcement/any other fixture,
welding where necessary, tying and holding to correct level, line and position, any
auxilliary dummy structures to support heavy sleeves etc. all complete for all depths
and heights as specified and directed. -
239 S006.18.00 MS Chequered Plates - Non FIM Items -
240 S006.18.01 Supplying, fabricating and erecting in position at all levels and locations bolted, MT 5.00 92,870.00 Nine Two Eight Seven 464,350.00
screwed and/or welded M.S. CHEQUERED PLATES of any thickness in walkways, Zero
platforms, stair treads, any other place as directed etc. including cutting to required
size, shape, making holes, notches, openings of required size, nosing, straightening if
required, making the edges smooth, removing the burrs, fixing, welding, preparation
and submission of fabrication drawings and preparing the surfaces for painting and
applying shop primer as per EIL Specification No. 6-79-0020 (or Job Specification,
wherever applicable) after fabrication etc. all complete as specified and directed.
(SUPPLY OF ALL MATERIALS IN CONTRACTOR'S SCOPE). -
241 S006.21.00 Rust Proof Fasteners - Non FIM Items -
242 S006.21.01 Supplying, handling, transporting to site of work and fixing approved RUSTPROOF Each 10.00 610.00 Six One Zero 6,100.00
EXPANSION FASTENERS M.S.bolts of medium duty upto & inclusive of 16mm dia.
at specified positions on concrete floors, roofs, beams (sides and bottom), walls,
columns etc. according to manufacturer's specifications including all accessories like
nuts, washers etc. of required size., testing, necessary scaffolding, drilling of the
holes in concrete surface with electric drill cleaning and making good any damage
done to the structure etc. all complete for all heights, depths and locations as
specified and directed. -
243 S006.21.03 Supplying, handling, transporting to site of work and fixing approved RUSTPROOF Each 10.00 650.00 Six Five Zero 6,500.00
EXPANSION FASTENERS M.S.bolts of medium duty beyond 16mm dia. upto &
inclusive of 25mm dia.at specified positions on concrete floors, roofs, beams (sides
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 56 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

and bottom), walls, columns etc. according to manufacturer's specifications including

all accessories like nuts, washers etc. of required size, testing, necessary scaffolding,
drilling of the holes in concrete surface with electric drill cleaning and making good
any damage done to the structure etc. all complete for all heights, depths and
locations as specified and directed. -
244 S006.26.00 Chemical Anchor Fastner -
245 S006.26.01 Supplying, handling, transporting to site of work and fixing approved CHEMICAL Each 10.00 1,100.00 One One Zero Zero 11,000.00
ANCHOR FASTENERS consisting of M.S. threaded rod of Grade 5.8, GALVANIZED
with minimum thickness of 5 microns and chemical (approved for use in cracked
concrete), packed in flexible chemical foil or dual foil type, to be used with the help of
dispenser, of 12mm dia. at specified positions on concrete floors, roofs, beams (sides
and bottom), walls, columns etc. according to manufacturer's specifications including
all accessories like nuts, washers etc. of required size, testing, necessary scaffolding,
drilling of the holes in concrete surface with electric drill, cleaning of holes with air
blowout & wire-brush and making good any damage done to the structure etc. all
complete for all heights, depths and locations as specified and directed.
-
246 S006.26.03 Supplying, handling, transporting to site of work and fixing approved CHEMICAL Each 10.00 1,700.00 One Seven Zero Zero 17,000.00
ANCHOR FASTENERS consisting of M.S. threaded rod of Grade 5.8, GALVANIZED
with minimum thickness of 5 microns and chemical (approved for use in cracked
concrete), packed in flexible chemical foil or dual foil type, to be used with the help
of dispenser, of 20mm dia. at specified positions on concrete floors, roofs, beams
(sides and bottom), walls, columns etc. according to manufacturer's specifications
including all accessories like nuts, washers etc. of required size., testing, necessary
scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes
with air blowout & wire-brush and making good any damage done to the structure etc.
all complete for all heights, depths and locations as specified and directed.
-
247 S007.00.00 BRICK MASONRY (REFER SPECIFICATION NO.6-68-0009) -
248 S007.14.00 CLASS 10.0 - Non FIM Items -
249 S007.14.01 Providing and laying BRICK MASONRY WITH BRICKS OF CLASS 10.0 in cement CuM 200.00 6,210.00 Six Two One Zero 1,242,000.00
mortar 1:6 (1 Cement : 6 Sand) in one or more brick thickness and in any shape
(excluding circular/ curved brick masonry) at all depths below plinth level including the
cost of materials, labour, scaffolding/ staging, sampling & testing, soaking of bricks,
cutting and laying of bricks, providing recesses, making openings of any shape &
size, finishing the joints flush below ground level and raking out the joints above
ground level, sealing the gap between masonry and soffit of beam/ slab, embedding
the fittings & fixtures, curing, etc. all complete as per specifications. ALL MATERIALS
INCLUDING CEMENT SUPPLIED BY THE CONTRACTOR. -
250 S007.14.02 Providing and laying BRICK MASONRY WITH BRICKS OF CLASS 10.0 in cement CuM 17200.00 6,510.00 Six Five One Zero 111,972,000.00
mortar 1:6 (1 Cement : 6 Sand) in one or more brick thickness and in any shape
(excluding circular/ curved brick masonry) at all heights above plinth level including
the cost of materials, labour, scaffolding/ staging, sampling & testing, soaking of
bricks, cutting and laying of bricks, providing recesses, making openings of any shape
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 57 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

& size, finishing the joints flush below ground level and raking out the joints above
ground level, sealing the gap between masonry and soffit of beam/ slab, embedding
the fittings & fixtures, curing, etc. all complete as per specifications. ALL MATERIALS
INCLUDING CEMENT SUPPLIED BY THE CONTRACTOR. -
251 S010.00.00 DEMOLISHING AND DISMANTLING (REFER SPECIFICATION NO. 6-68-0012) -
252 S010.01.00 Brickwork - Non FIM Items -
253 S010.01.01 Demolishing BRICKWORK (taking all necessary safety precautions) for all depths Cu.m. 10.00 680.00 Six Eight Zero 6,800.00
below plinth level including supply of all tools and tackles, necessary scaffolding,
propping, underpinning, cleaning and stacking of serviceable material, disposal of
unserviceable material to spoil heaps anywhere within the plant boundary, all
complete as specified and directed. (Excavation & backfilling shall be paid separately
under relevant items). -
254 S010.01.02 Demolishing BRICKWORK (taking all necessary safety precautions) for all heights Cu.m. 10.00 730.00 Seven Three Zero 7,300.00
above plinth level including supply of all tools and tackles, necessary scaffolding,
propping, underpinning, cleaning and stacking of serviceable material, disposal of
unserviceable material to spoil heaps anywhere within the plant boundary, all
complete as specified and directed. -
255 S010.02.00 RCC - Non FIM Items -
256 S010.02.01 Demolishing RCC WORK (taking all necessary safety precautions) for all depths Cu.m. 10.00 2,750.00 Two Seven Five Zero 27,500.00
below plinth level including supply of all tools & tackles, necessary scaffolding,
propping, underpinning etc., cutting, straightening, scraping and cleaning of
reinforcement bars, stacking of serviceable materials, disposal of unserviceable
material to spoil heaps anywhere within the plant boundary, all complete as specified
and directed. (Excavation & backfilling shall be paid separately under relevant
items). -
257 S010.02.02 Demolishing RCC WORK (taking all necessary safety precautions) for all heights Cu.m. 10.00 3,210.00 Three Two One Zero 32,100.00
above plinth level including supply of all tools & tackles, necessary scaffolding,
propping, underpinning etc., cutting, straightening, scraping and cleaning of
reinforcement bars, stacking of serviceable materials, disposal of unserviceable
material to spoil heaps anywhere within the plant boundary, all complete as specified
and directed. -
258 S010.02.03 Chipping of RCC WORK (taking all necessary safety precautions) by CHISELLING, Sq.m. 10.00 250.00 Two Five Zero 2,500.00
upto & inclusive of 25mm thickness including supply of all tools & tackles, necessary
scaffolding, propping, underpinning etc., cutting, lapping/welding of reinforcement
bars as per drawings, disposal of the unserviceable material to spoil heaps anywhere
within the plant boundary, all complete at all heights and depths, as specified and
directed. (Excavation and backfilling shall be paid separately under relevant items). -
259 S010.02.11 Making cut-outs in RCC slab/ wall upto a thickness of 400mm (taking all necessary Cu.m. 1.00 12,600.00 One Two Six Zero Zero 12,600.00
safety precautions) by vibration-less spark-free mechanical means like core-cutting,
wet cutting by diamond wall saw system at all depths & heights including supply of all
tools & tackles, necessary scaffolding etc. cutting of reinforcement bars, disposal of
unserviceable material, plastering & finishing the cut surfaces, all complete as
specified and directed by the Engineer-in- Charge (Measurement on Plan/ Elevation
Area basis). -
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 58 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

260 S010.04.00 PCC _ Non FIM Items -

261 S010.04.01 Demolishing PLAIN CEMENT CONCRETE work (taking all necessary safety Cu.m. 10.00 1,320.00 One Three Two Zero 13,200.00
precautions) for all depths below plinth level including supply of all tools & tackles,
necessary scaffolding, propping, underpinning etc. disposal of unserviceable material
to spoil heaps anywhere within the plant boundary, all complete as specified and
directed. (Excavation and backfilling shall be paid separately under relevant items) -
262 S010.04.02 Demolishing PLAIN CEMENT CONCRETE work (taking all necessary safety Cu.m. 10.00 1,150.00 One One Five Zero 11,500.00
precautions) for all heights above plinth level including supply of all tools & tackles,
necessary scaffolding, propping, underpinning etc. disposal of unserviceable material
to spoil heaps anywhere within the plant boundary, all complete as specified and
directed. -
263 S010.06.00 Steelwork - Non FIM Items -
264 S010.06.01 Dismantling bolted/rivetted/welded STRUCTURAL STEEL WORK of all descriptions MT 1.00 10,500.00 One Zero Five Zero Zero 10,500.00
(taking all necessary safety precautions), including supply of all tools and tackles,
consumables, necessary scaffolding etc., providing temporary bracings as required,
cutting (by flame or saw) gusset plates, bolts, nuts, weldings etc., transporting and
stacking of the serviceable materials, cleaning the site of work of all unserviceable
materials for disposal to spoil heaps anywhere within the plant boundary, all complete
at all depths and heights, as specified and directed. -
265 S011.00.00 MISCELLANEOUS ITEMS (REFER SPECIFICATION NO. 6-68-0013) -
266 S011.01.00 Antitermite - Non FIM Items -
267 S011.01.01 Providing and injecting approved chemical emulsions as specified for pre- Sq.m. 58020.00 360.00 Three Six Zero 20,887,200.00
constructional ANTI-TERMITE TREATMENT and creating a chemical barrier under
and around column pits, wall trenches, basement excavations, top surfaces of plinth
filling, junction of wall and floor, along the external perimeter of building, expansion
joints, surrrounding of pipes and conduits etc. all complete as specified and directed.
(Plinth area of the building at ground floor only shall be measured). -
268 S011.06.00 Sand Filling - Non FIM Items -
269 S011.06.01 Supplying and filling approved SAND of specified quality under floors, in foundations, Cu.m. 11600.00 1,500.00 One Five Zero Zero 17,400,000.00
plinths, tank foundations etc. for all depths and heights including cost of
sand,royalties, transportation to site for all leads and lifts,including loading, unloading,
spreading in layers of loose thickness not exceeding 150
mm,watering,ramming,compacting with mechanical compactors and/or other
equipment to the specified levels to achive 85% relative density as per IS:2720 Part
XIV,including preparation of subgrade to the required slope,providing testing
apparatus and testing the degree of consolidation all complete as per drawings,
specifications and direction of Engineer-in-charge.The rates shall be inclusive of the
cost of all labour,material,equipments etc. all complete . -
270 S011.07.00 DPC - Non FIM Items -
271 S011.07.01 Providing and laying 40mm thick DAMP PROOF COURSE with plain cement Sq.m. 2210.00 580.00 Five Eight Zero 1,281,800.00
concrete of nominal mix of 1:1.5:3 with 10mm & down size graded crushed stone
aggregates in two layers of 20mm thick with two coats of hot bitumen (Grade A90/S90

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 59 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

conforming to IS:73) applied @ 1.7 Kg/sq.m. over each layer as per specifications
including cleaning, watering the top surface of walls, centering, shuttering, placing,
tamping, curing, sprinkling an even layer of dry & sharp sand over the hot bitumen
etc. all complete as specified and directed. -
272 S011.10.00 BI-POLAR CONCRETE PENETRATING CORROSION INHIBITING ADMIXTURE -
273 S011.10.01 Supplying and mixing of approved brand of BI-POLAR CONCRETE PENETRATING KG 258530.00 150.00 One Five Zero 38,779,500.00
CORROSION INHIBITING ADMIXTURE in concrete as per manufacturer's
specification for protection of reinforcement against corrosion. Supply of admixture in
Contractor's scope. -
274 S014.00.00 BONDING FRESH CONCRETE TO OLD CONCRETE BY EPOXY RESIN BONDING
SYSTEM (REFER SPECIFICATION NO. 6-68-0056) -
275 S014.01.00 Epoxy Resin - non FIM Items -
276 S014.01.01 Providing and applying approved EPOXY RESIN (prepared as per manufacturer's Kg. 10.00 1,800.00 One Eight Zero Zero 18,000.00
recommendation) for bonding of fresh concrete to old concrete in all types of structure
at all depths and heights including cleaning of concrete surface, removing of all loose
concrete pieces, making rough by chiselling, taking off the skin of concrete,
application of Epoxy Resin System by spraying, necessary working platforms, props,
scaffolding and other safety measures, removal of same after completion etc. all
complete as specified and directed. (Excavation, backfilling, removal of surplus earth,
keeping pit dry by pumping/bailing subsoil water shall be paid separately under
relevant items). -
277 S999.00.00 Miscellaneous -
278 S999.99.00 Miscellaneous -
279 S999.99.99V12 Providing and laying HALF BRICK MASONRY with bricks of CLASS 10.0 in cement SQM 50.00 750.00 Seven Five Zero 37,500.00
mortar 1:4 (1 Cement : 4 Sand)in any shape, including the cost of materials, labour,
scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of
bricks, providing openings of any shape & size, raking out the joints, supplying and
placing 2 Nos. 6mm dia. M.S. Bars at every fourth course, sealing the gap between
masonry and soffit of beam/slab, embedding the fittings and fixtures, curing etc. all
complete as per specification.ALL MATERIALS INCLUDING CEMENT SUPPLIED
BY CONTRACTOR. -
280 GC GENERAL CIVIL -
281 C034.00.00 PLUMBING AND BUILDING DRAINAGE (Spec. No. 6-65-0053) -
282 C034.07.00 Supplying and fixing gun metal globe valve conforming to IS:778, complete as per
specifications and directions of Engineer-in-Charge. -
283 C034.07.01V05 Dia 32 mm , - EACH 55.00 2,030.00 Two Zero Three Zero 111,650.00
284 C034.22.00 Construction as per EIL Std.7-65-0215 of brick masonry (brick class shall be as
mentioned below) inspection chambers/manholes of 750mmx750mm internal size
1000mm deep(Max.) in cement mortar 1:4 (1 cement: 4 sand) with CI frame and
cover 500mm clear dia, (circular Medium duty of grade MD-10) conforming to IS:1726
fixed on RCC slab of M-30 grade, necessary excavation, supplying, fixing 4 Nos.
16mm dia M.S. rungs, M-20 grade foundation concrete 1:3 cement mortar(1 cement:
Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 60 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

3 sand) plastering of 13mm average thickness for inside & 16mm avg. thickness for
outside exposed surfaces, backfilling, disposal of surplus earth upto a lead of 100M,
benching with M-20 grade cement concrete and rendering smooth with a neat coat of
cement slurry, painting the C.I. frame and cover with two coats of chlorinated rubber
zinc phosphate primer @ 40μ DFT per coat and finish painting consists of two coats
of chlorinated rubber paint @40μ DFT per coat etc. all complete as per drawings,
specifications and directions of Engineer-in-Charge. -
285 C034.22.02V02 All materials including cement supplied by contractor and Brick Class 10 , - EACH 35.00 28,000.00 Two Eight Zero Zero 980,000.00
Zero
286 C034.25.00 Supplying, laying and fixing 3 layer PP-R (Poly Propylene Random copolymer) pipes
above ground. Pipes shall conform to IS:15801; SDR 7.4 U V stabilized &
antimicrobial fusion welded, having thermal stability for hot & cold water supply,
including supply and fixing of all PP-R plain & brass threaded polypropylene random
fittings, PP-R Male adopters, including fixing in floors, walls, supporting on columns,
sleepers, embedding, jointing, including bends, elbows, tees, reducers, sockets,
unions and other specials, supplying and fixing with hooks/clamps in wooden plugs,
cutting pipes to required lengths, making connections, cutting chases or holes in walls
& making good the same, testing etc all complete as per drawings, manufacturer
specifications and directions of Engineer-in-Charge. For the following Nominal Bore
(NB) pipe: -
287 C034.25.01V04 Nominal Dia 20 mm , - M 350.00 230.00 Two Three Zero 80,500.00
288 C034.25.01V05 Nominal Dia 25 mm , - M 350.00 290.00 Two Nine Zero 101,500.00
289 C034.25.01V06 Nominal Dia 32 mm , - M 710.00 360.00 Three Six Zero 255,600.00
290 C034.25.01V07 Nominal Dia 40 mm , - M 25.00 450.00 Four Five Zero 11,250.00
291 C034.29.00 Supplying, laying and jointing of above ground approved quality HDPE pipes to be
used for soil and waste discharge application inside buildings conforming to IS:14333
including all necessory fittings/ specials such as bends, Y junction, T junction (both
single and double) plugs, coupler, adapter, shoes etc. including jointing and testing as
per manufacturers recommendations, cutting floors/walls and making good the same
after fixing including supply and fixing hooks/ clamps etc. complete as per drawings,
specifications and directions of Engineer-in-Charge. For the following nominal
diameter (mm) Pressure Rating(PN) -
292 C034.29.02V01 (All material including cement supplied by contractor)( Dia (Nominal) - mm Pressure M 270.00 610.00 Six One Zero 164,700.00
Rating - PN )Nominal Dia 90 mm , Pressure Rating 6 PN , -
293 C034.29.02V02 (All material including cement supplied by contractor)( Dia (Nominal) - mm Pressure M 520.00 910.00 Nine One Zero 473,200.00
Rating - PN )Nominal Dia 110 mm , Pressure Rating 6 PN , -
294 C034.30.00 Supplying, laying and jointing of underground approved quality HDPE pipes to be
used for soil and waste discharge application inside buildings conforming to IS:14333
including all necessory fittings/ specials such as bends, Y junction, T junction (both
single and double), plugs, coupler, adapter etc. including jointing and testing as per
manufacturers recommendations, cutting in floors, earth work in excavation, encasing
the pipe in 50mm thick PCC M20, backfilling and disposal of surplus earth / debris to
demarcated area anywhere within plant complex limit etc. complete as per drawings,

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 61 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

specifications and directions of Engineer-in-Complete. For the following nominal

diameter (mm) Pressure Rating(PN) -
295 C034.30.02V01 (All material including cement supplied by contractor)( Dia (Nominal) - mm Pressure M 130.00 640.00 Six Four Zero 83,200.00
Rating - PN )Nominal Dia 90 mm , Pressure Rating 6 PN , -
296 C034.30.02V02 (All material including cement supplied by contractor)( Dia (Nominal) - mm Pressure M 250.00 950.00 Nine Five Zero 237,500.00
Rating - PN )Nominal Dia 110 mm , Pressure Rating 6 PN , -
297 C034.31.00 Supplying and fixing approved quality HDPE Floor Trap with CP pressed steel grating EACH 175.00 1,350.00 One Three Five Zero 236,250.00
including cutting floors and making good the same , etc., making inlet and outlet
connections etc. complete for 110mm inlet and 90mm outlet as per drawings,
specifications and directions of Engineer-in-Charge. -
298 C034.32.00 Supplying and fixing approved quality HDPE Floor Trap with CP pressed steel grating EACH 70.00 1,500.00 One Five Zero Zero 105,000.00
including cutting floors and making good the same , etc., making inlet and outlet
connections etc. complete for 110mm inlet and 110mm outlet as per drawings,
specifications and directions of Engineer-in-Charge. -
299 C034.33.00 Providing and fixing approved quality HDPE 160mmx110mm dia. gully trap as per job
drawing/standard including grating with CI frame and cover 300mmx300mm including
brick masonry (brick class shall be as mentioned below) chamber in 1:4 cement
mortar( 1 cement: 4 sand) on M-20 grade cement concrete foundation, plastered
inside and outside surfaces with 1:3 cement mortar (1 cement: 3 sand) with 13mm
average thickness including providing and fixing light duty CI frame and cover,
painting CI frame and cover with two coats of chlorinated rubber zinc phosphate
primer @ 40 micron DFT per coat and finish painting consists of two coats of
chlorinated rubber paint @40 micron DFT per coat, earth work in excavation,
backfilling, removal of surplus earth, benching with M-20 grade cement concrete and
rendering smooth with a neat coat of cement slurry etc. all complete as per drawings,
specifications and directions of Engineer-in-Charge. -
300 C034.33.02V01 All materials including cement supplied by contractor andBrick Class 5 , - EACH 35.00 4,300.00 Four Three Zero Zero 150,500.00
301 C034.34.00 Supply and installation on terrace, circular drinking water tank, of polyethylene with
PUF insulation for temprature control, material conforming to BIS codes including
supply and installation of all fittings, cover with suitable locking arrangement, float
valve, making necessary holes for inlet, outlet and overflow connection and vent pipe
etc. and the base supports for tank including supply of all necessary material all
complete as per specifications and directions of Engineer-in-charge. For following
capacities -
302 C034.34.01V01 Capacity 500 Litres , - EACH 17.00 6,300.00 Six Three Zero Zero 107,100.00
303 C034.34.01V02 Capacity 1000 Litres , - EACH 6.00 12,600.00 One Two Six Zero Zero 75,600.00
304 C245.00.00 Under Ground Sewer System - HDPE Pipe -
305 C245.01.00 Supplying, laying and jointing of underground approved quality HDPE pipes to be
used for soil and waste discharge or rain water application outside buildings
confirming to IS: 14333 including all necessory fittings/ specials such as bends, Y
junction, T junction (both single and double), plugs, coupler, adapter etc. including
solvent welded jointing and testing as per manufacturers reommendations , including
earthwork in excavation in all types of soil for pipe trenches, etc. including dewatering,

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 62 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS
The drawing, design and details given in this format are the property of ENGINEERS INDIA LIMITED. They are merely loaned on the borrower's express agreement that they will not be reproduced, copied, exhibited or
used, except in the limited way permitted by a written consent given by the lender to the borrower for the intended use. .A4 297 x 210.

SOR NO B018-000-81-41-CJ-SOR- SOR Title Civil-Structural and Architectural Works Department STRUCTURAL
8105-0-0M
S No. Item No Description UOM Quantity Rate (INR) Rate (INR) in words Amount (INR)

shoring and strutting if necessary, dressing of sides, leveling, grading and ramming of
bottoms, cutting the pipes to required lengths, lowering the pipes to proper grade and
alignment, jointing, including connecting the pipes to manholes by using concrete
manhole adapters and grouting the pipe body with manhole wall using cement mortar
1:2 (1cement : 2 sand), testing, draining of water and
cleaning of pipe after testing, backfilling the trenches with select material from
available excavated soil including re excavating the deposited soil excavated earlier
breaking clods and laying in layers of 15cm compacted thickness , watering and
compacting with mechanical means like vibro rammers etc. to 90% standard proctor
density as per IS:2720 Part-VII, making good the surface, including cutting of roads
wherever required and making good the same, disposal of surplus earth/
unserviceable material to demarcated area anywhere within the complex limit etc.
complete for all depths as per drawings, specifications and instructions of Engineer-
in-Charge. -
306 C245.01.02V01 (All material including cement supplied by contractor) Nominal Dia 160 mm , Pressure M 310.00 2,060.00 Two Zero Six Zero 638,600.00
Rating 6 PN , -
SOR Level Total: 2,062,790,340.00
Grand Total: 2,622,244,730.00
Rebate (%): .0000
Rebate amount: 0.00
Net Contract Value: 2,622,244,730.00

Contractor Seal & Signature Client Seal & Signature Job No B018 JTN 8105 Part No 0 Page 63 of 63
. HMEL / HMPL Project Name HMEL PETROCHEMICAL COMPLEX
Bid Doc No B018-000-CJ-T-8105/1015
Contract Title PLANT BUILDINGS