International. Enviroline, 376F-60 PRooucT DESCRIPTION INTENDED USES PRACTICAL INFORMATION FOR ENVIROLINE 276F-0 REGULATORY DATA Epoxy Novolac ‘A solvent free. two component polycyclamine cured ning system utilising advanced epoxy novolac technology with flake and fire reinforcement Enviroline 376F-50 is a new generation system providing improved performance benefits; - Meets API 652 (October 2006) Excellent chemical and solvent resistance “High temperature immersion resistance (eg crude up to 99°C (200°) “Fast cure (rapid return to service in 14 hours at 25°C (77°F) Thermal and mechanical shock resistance “ultra low VOC = Single coat application up to 2000 microns (80 mils) ~ Cathadic Disbordiment resistance + Excellent abrasion and impact resistance ‘Applications include steel and concrete ining in the oll and gas, chemical, mining and water indusines on assets such as crude and petroleum bulk storage tanks, downhole tubulars, downhole casing exteriors, intenor and exterior pipes, floors, tank pads, trenches, troughs, sumps and pits. Using Enviroline 376F-60 in conjunction with API 653 inspection and API 852 guidelines asa thick fim reinforced ining allows internal inspection intervals tobe set at the maximum tme allowable; Potentially 20 years, (oss Level Not applicable Volume Solids 100% “Typical Thickness 41250-2000 microns (50-80 mils) dry equivalent to 11250-2000 microns (50-80 mis) wet 0.50 mitre at 1850 miccons aft and stated volume solids 24 sa MUS gallon at 66 mils d.{t and stated volume solids, ‘Allow appropriate loss factors. Refer to Enviraline Application Guidelines for advice on fim thickness determination Mothod of Application Plural Component Aitess Spray, Airless Spray Drying Time Overcoating interval wit self ‘Temperature Touch Dry Hard Dry Minimo Maxirourn SC GF) T hours Tahours? Thou 2ohoue asc (TF) 2hours 4 hours! 25 hours 6 hours? 35°C (95°F) ‘hour 2hours* 2 hours hours? Sufficient coating fim strength has developed to permit the handing and movement af coated steelwork. A Shore D hardness reading of 75-80 is a recommended guideline to indicate sutabilty for return to service. * Ifthe maximum overcoating intervals exceeded it will be necessary to thoroughly abrade the surface ofthe lining with coarse emery paper. Flash Point (Typical) Mixed 68°C (151°F) Product Weight 1.53 kgil (12.8 Ib/gal) vor 0.35 tigal (42 git) EPA Method 24 Tak EU Solvent Emissions Directive (Council Directive 1989/13/EC) See Product Characteristics section for further details Protective Coatings Worldwide Product Jie” ‘AkazoNobelInternational. Enviroline, 376F-60 SURFACE PREPARATION [APPLICATION Epoxy Novolac {All surfaces tobe coated should be clean, dry and free ftom contamination. Prior to application all ‘surfaces should be assessed and treated in accordance with ISO 8504.2000 Where necessary, remove weld spatter and where required smooth weld seams and sharp edges. Cl or grease should be removed in accordance with SSPC-SP1 solvent clearing. Abrasive Blast Cleaning Best performance wil alvays be achieved when Envitoline 376F-60 is applied to surfaces prepared by abrasive blast cleaning to Sa® (ISO 8501-1:2007) or SSPC-SPS. Where Enviroline 375F-60 is not to be used in high heat andlor aggressive service, preparation to Sa2¥ {ISO 8501-12007) or 'SSPC-SP10 may be acceptable. A sharp, angular surface profle of 75125 microns (3-5 mils) 's Fecommended. Contact International Protective Coatings for futher information. Enviroline 376F-50 must be applied before oxidation ofthe steel occurs. If oxidation does occur the ‘entire oxidised area should be reblasted tothe standard specified above. Surface defects revealed by the blast cleaning process should be ground, filed or treated in the appropriate manner. ‘The preferred method of holding the blast standard is by dehumidification, Alematively, an approved holding primer may be used. Concrete Surfaces Refer to Intemational Protective Coatings for specific recommendations. Mong Material is supplied in two containers as a unit. Complete units should be stored, mixed and applied in accordance withthe Envialine Application Guidelines. Mix Ratio 2 parts): 1 part(s) by volume Working Pot Lite 40°C (104°F) 10 minutes. Plural Component Recommended Refer to Enviroline Applicaton Guidelines for Altos Spray, more details Airs Spray Suitable Reter to Enviroine Application Guidelines for more details ‘lr Spray Not suitable (Proseure Pot) Brush Suitable (Can be used for the touch-up of small areas or for stripe coating of welds and edges. ‘Thinner Not normaly required Refer to Enviroline Application Guidelines for specie advice Cleaner Enviroline 71. Work Stoppages Do nat allow material to remain in hoses, gun or spray equipment Thoroughly tush al equipment with Envioline 71C. Once units of pain have been mixed, they should not be resealed and itis advised that ater prolonged stoppages. work recommences wih freshly mixed unis. Clean up Clean all equipment immediately after use with Enviroline 71, Itis good working practice to periodically fush out spray equipment during the course of the working day. Frequency should depend upon amount sprayed, temperature and elapsed time, including any delays. All surplus material and empty containers should be disposed of in ‘accordance with appropriate regional regulatons/legislationInternational. Enviroline, 376F-60 PRODUCT CHARACTERISTICS sysTeMs COMPATIBILITY Epoxy Novolac ‘The detailed Envirotine Application Guidelines should be consulted prior to use. ‘This datasheet provides general guidance on the use of Enviroline 376F-60. Specific project, requirements will be dependent upon the service end use and operating conditions of the tank or vessel. Always consult International Protective Coatings to confirm that Enviroline 376F-60 is suitable for contact with the product to be stored. ‘The detailed project coating specification provided by International Protective Coatings must be followed at all times. ‘Stripe coating isan essential part of good working practice and as such should form part of any lining specification For heavily pitted or porous steel, spray apply approximately 50% of the required film thickness and follow immediately wth a short nap roller or squeegee to work material into the bottom of pitted For plural component aifess spray application, best results willbe achieved when the product is heated pror to application, Part A (Resin) to a maxmum of 60°C (140°F) and Part B (Hardener) to 8 maximum of 40°C (105°F). For airless spray application, best results willbe achieved when each component of the product is heated prior to application to 35-37°C (95-100'F) Surface temperature must always be @ minimum of 3C (5'F) above dew point Use the following chart for preferred temperature conditions. These conditions plus adequate ventilation must be maintained throughout the curing cycle. ‘Substrate Temperature Ait Temperature Preferred 21-48°C(70-120°F)21-38°C (70-100°F) Minimum 13°C (55°F) 43°C (65°F) [After the coating system has cured hard, the dy fm thickness should be measured using @ ‘suitable nondestructive magnetic gauge to verity the minimum applied system thickness. The coating system should be free ofall pinholes or ather holidays, The cured fim should be essentially {tee of runs, sags, drips, inclusions or other defects. All defciencies and defects should be corrected, The repaired areas shallbe rested and allowed to cure as speciied before placing the finished lining into service Post-curing is not necessary for most applications, but Envioline 376F-80 may be post-cured to ‘expedite curing or increase chemical resistance for extremely aggressive environments, Past-cure fora minimum of 2 hours at 121°C (250°F) or 6-8 hours at 66°C (150°F) for maximum resistance. Maximum continuous dry temperature resistance for Enviroline 376F-60 is 149°C (300"F) Note: VOC values are typical and are provided for guidance purpose only. These may be subject to vatiation depending on factors such as differences in colour and nermal manufacturing tolerances, Low molecular weight reactive adcitves, which will form part of the flm during normal ambient cure conditions, wil also affect VOC values determined using EPA Method 24 Enviroline 376F-50 should always be applied to correctly prepared substrates. When a primer is, required as part of tne coating spectication, consul Intemational Protective Coatings for spectic advice, Enviroline 376F-50 's designed as a single coat system. It must only be avercoated with itself ‘should re-coats or touch-up be requiredInternational. Enviroline, 376F-60 Epoxy Novolac ‘ADDITIONAL Further information regarding industry standards, terms and abbreviations used inthis data sheet INFORMATION ‘can be found in the fllowing dacuments avalable at www internatonal-pe.com: + Defitions & Abbreviations + Surface Preparation + Paint Applicaton + Theoretical & Practical Coverage + Envroine Application Guidetines Individual copies of these information sections are available upon request. sarery ‘This product is intended for use only by professional applicators in industrial stations. PRECAUTIONS ‘Al work involving the application and use of ths product should be performed in compliance with all relevant national Health, Safety and Environmental siandards, regulations and legislation, Proper ventlation must be provided during application and afterwards during curing (refer to product datasheets for typical curing times) to ensure safe limits and prevent fires and explosions. Forced extraction will be required in confined spaces. Ventilation andior respiratory personal protective equipment (arfed hoods or appropriate cartridge masks) must be provided during application ang curing. Take precautions to avoid skin and eye cantact (overalls, gloves, goggles, masks, barrier cream etc). Before use, obtain, ead and then follow the advice given on the Material Safety Data Sheets (Parts ‘A and B if two-pack) and the Health and Safety section ofthe Coatings Applications Procedures for this product In the event that welding or flame cutting is performed on metal coated with tis product, dust and fumes will be emitted which will requir the use of appronsate personal protective equipment and adequate local exhaust ventilation, ‘The detailed safety measures are dependent on application methods and the work environment. If you do not fully understand these warnings and instructions or if you cannat srtly comply with them, do nat use the product and consult International Protective Coatings. Warning: This product contains liquld epoxies and modified polyamines and may cause skin ‘sensitisation if not used correctly PACK SIZE nt size Pena Pane AUSgal «27S eM SUSgel 13S oN 2US For vali of ter pack es coc ItematonslPotcive Costas SHIPPING WEIGHT nt sae Pate Pata (rrricaly Usa masie 1850 eit saseke sat4ke STORAGE, Shot Lite 24 months minimum at 25°C (77°F) in original, unopened containers. ‘Subject to resnspection thereafter. Store indy, shaded candtons away {fom sources of heat and grt. ‘tere ties ore Romo Takeo es neon Par mph ae Cooytght © AkzoNobe, 2703/2014