Product Sample & Technical Tools & Support & Reference

Folder Buy Documents Software Community Design

LM22677, LM22677-Q1
SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015

LM22677/-Q1 42-V, 5-A SIMPLE SWITCHER®, Step-Down Voltage Regulator

With Features
1 Features 3 Description
•
1 Wide Input Voltage Range: 4.5 V to 42 V The LM22677 switching regulator provides all of the
functions necessary to implement an efficient high-
• Internally Compensated Voltage Mode Control voltage step-down (buck) regulator using a minimum
• Stable With Low ESR Ceramic Capacitors of external components. This easy-to-use regulator
• 100-mΩ N-Channel MOSFET incorporates a 42-V N-channel MOSFET switch that
• Output Voltage Options: can provide up to 5 A of load current. Excellent line
and load regulation along with high efficiency (> 90%)
– -ADJ (Outputs as Low as 1.285 V) are featured. Voltage mode control offers short
– -5.0 (Output Fixed to 5 V) minimum on-time, allowing the widest ratio between
• ±1.5% Feedback Reference Accuracy input and output voltages. Internal loop compensation
means that the user is free from the tedious task of
• 500-kHz Default Switching Frequency calculating the loop compensation components. Fixed
• Adjustable Switching Frequency and 5-V output and adjustable output voltage options are
Synchronization available. The default switching frequency is set at
• –40°C to +125°C Operating Junction Temperature 500 kHz, thus allowing for small external components
Range and good transient response. In addition, the
frequency can be adjusted over a range of 200 kHz
• Precision Enable Input to 1 MHz with a single external resistor. The internal
• Integrated Boot-Strap Diode oscillator can be synchronized to a system clock or to
• Integrated Soft-Start the oscillator of another regulator. A precision enable
input allows simplification of regulator control and
• Fully WEBENCH® Enabled system power sequencing. In shutdown mode the
• LM22677-Q1 is an Automotive-Grade Product regulator draws only 25 µA (typical). The LM22677
that is AEC-Q100 Grade 1 Qualified (–40°C to also has built-in thermal shutdown, and current
+125°C Operating Junction Temperature) limiting to protect against accidental overloads.
• NDR (Exposed Pad) The LM22677 device is a member of Texas
Instruments' SIMPLE SWITCHER® family. The
2 Applications SIMPLE SWITCHER concept provides for an easy-to-
• Industrial Control use complete design using a minimum number of
external components and the TI WEBENCH design
• Telecom and Datacom Systems tool. TI's WEBENCH tool includes features such as
• Embedded Systems external component calculation, electrical simulation,
• Conversions from Standard 24-V, 12-V and 5-V thermal simulation, and Build-It boards for easy
Input Rails design-in.

Simplified Application Schematic Device Information(1)

PART NUMBER PACKAGE BODY SIZE (NOM)
VIN
VIN FB LM22677
TO-263 (7) 10.16 mm x 9.85 mm
LM22677-ADJ BOOT LM22677-Q1
VOUT (1) For all available packages, see the orderable addendum at
SW
RT/SYNC EN GND the end of the data sheet.

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM22677, LM22677-Q1
SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015 www.ti.com

Table of Contents
1 Features .................................................................. 1 7.4 Device Functional Modes........................................ 12
2 Applications ........................................................... 1 8 Applications and Implementation ...................... 15
3 Description ............................................................. 1 8.1 Application Information............................................ 15
4 Revision History..................................................... 2 8.2 Typical Application .................................................. 16
5 Pin Configuration and Functions ......................... 3 9 Power Supply Recommendations...................... 19
6 Specifications......................................................... 4 10 Layout................................................................... 19
6.1 Absolute Maximum Ratings ...................................... 4 10.1 Layout Guidelines ................................................. 19
6.2 ESD Ratings: LM22677 ............................................ 4 10.2 Layout Example .................................................... 20
6.3 ESD Ratings: LM22677-Q1 ...................................... 4 10.3 Thermal Considerations ........................................ 21
6.4 Recommended Operating Conditions....................... 4 11 Device and Documentation Support ................. 22
6.5 Thermal Information .................................................. 4 11.1 Documentation Support ........................................ 22
6.6 Electrical Characteristics........................................... 5 11.2 Related Links ........................................................ 22
6.7 Typical Characteristics .............................................. 6 11.3 Trademarks ........................................................... 22
7 Detailed Description .............................................. 8 11.4 Electrostatic Discharge Caution ............................ 22
7.1 Overview ................................................................... 8 11.5 Glossary ................................................................ 22
7.2 Functional Block Diagram ......................................... 8 12 Mechanical, Packaging, and Orderable
7.3 Feature Description................................................... 8 Information ........................................................... 22

4 Revision History
Changes from Revision N (November 2014) to Revision O Page

• Changed the word Pin to Input............................................................................................................................................... 1

• Changed the Q grade part number corrected to LM22677 from LM2677'; added icon for Reference Design to top navs ... 1
• Changed "PFM" Package to "NDR" Package ....................................................................................................................... 3

Changes from Revision M (April 2013) to Revision N Page

• Added Pin Configuration and Functions section, Handling Rating table, Feature Description section, Device
Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information
section ................................................................................................................................................................................... 1
• Deleted Inverting Regulator Application ............................................................................................................................... 15

2 Submit Documentation Feedback Copyright © 2008–2015, Texas Instruments Incorporated

Product Folder Links: LM22677 LM22677-Q1

 LM22677, LM22677-Q1
www.ti.com SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015

5 Pin Configuration and Functions

NDR Package
7-Pin TO-263
Top View

7 EN
6 FB
5 RT/SYNC
4 GND
3 BOOT
2 VIN
1 SW

Exposed Pad
Connect to GND

Pin Functions
PIN
TYPE (1) DESCRIPTION APPLICATION INFORMATION
NAME NO.
SW 1 O Switch output Switching output of regulator
VIN 2 I Input voltage Supply input to the regulator
BOOT 3 I Bootstrap input Provides the gate voltage for the high side N-FET
Ground input to
GND 4 — regulator; system System ground pin
common
Oscillator mode control Used to control oscillator mode of regulator. See Switching Frequency
RT/SYNC 5 I
input Adjustment and Synchronization section of data sheet.
FB 6 I Feedback input Feedback input to regulator
Used to control regulator start-up and shutdown. See Precision Enable
EN 7 I Enable input
and UVLO section of data sheet.
Connect to ground. Provides thermal connection to PCB. See
EP EP — Exposed Pad
Applications and Implementation.

(1) O = Output, I = Input, G = Ground, P = Power

Copyright © 2008–2015, Texas Instruments Incorporated Submit Documentation Feedback 3

Product Folder Links: LM22677 LM22677-Q1
LM22677, LM22677-Q1
SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015 www.ti.com

6 Specifications
6.1 Absolute Maximum Ratings (1) (2)
MIN MAX UNIT
VIN to GND 43 V
EN Pin Voltage –0.5 6 V
RT/SYNC Pin Voltage –0.5 7 V
(3)
SW to GND –5 VIN V
BOOT Pin Voltage VSW + 7 V
FB Pin Voltage –0.5 7 V
Power Dissipation Internally Limited
Junction Temperature 150 °C
For soldering specifications, refer to Application Report Absolute Maximum Ratings for Soldering (SNOA549).
Storage temperature, Tstg –65 150 °C

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur, including inoperability and degradation of
device reliability and/or performance. Functional operation of the device and/or non-degradation at the absolute maximum ratings or
other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating
Conditions indicate conditions at which the device is functional and should not be operated beyond such conditions.
(2) If Military/Aerospace specified devices are required, contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) The absolute-maximum specification of the ‘SW to GND’ applies to dc voltage. An extended negative voltage limit of –10 V applies to a
pulse of up to 50 ns.

6.2 ESD Ratings: LM22677

VALUE UNIT
(1)
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 ±2000 V

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

6.3 ESD Ratings: LM22677-Q1

VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per AEC Q100-002 (1) ±2000 V

(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.

6.4 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN MAX UNIT
VIN Supply Voltage 4.5 42 V
Junction Temperature –40 125 °C

6.5 Thermal Information

LM22677
THERMAL METRIC (1) (2) NDR (TO-263) UNIT
7 PINS
RθJA Junction-to-ambient thermal resistance 22 °C/W

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report (SPRA953).
(2) The value of RθJA for the NDR (TJ) package of 22°C/W is valid if package is mounted to 1 square inch of copper. The RθJA value can
range from 20 to 30°C/W depending on the amount of PCB copper dedicated to heat transfer. See application note AN-1797 TO-263
THIN Package (SNVA328) for more information.

4 Submit Documentation Feedback Copyright © 2008–2015, Texas Instruments Incorporated

Product Folder Links: LM22677 LM22677-Q1

 LM22677, LM22677-Q1
www.ti.com SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015

6.6 Electrical Characteristics

Typical values represent the most likely parametric norm at TA = TJ = 25°C, and are provided for reference purposes only.
Unless otherwise specified: VIN = 12 V.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
LM22677-5.0
VIN = 8 V to 42 V 4.925 5.0 5.075
VFB Feedback Voltage V
VIN = 8 V to 42 V, –40°C ≤ TJ ≤ 125°C 4.9 5.1
LM22677-ADJ
VIN = 4.7 V to 42 V 1.266 1.285 1.304
VFB Feedback Voltage V
VIN = 4.7 V to 42 V, –40°C ≤ TJ ≤ 125°C 1.259 1.311
ALL OUTPUT VOLTAGE VERSIONS
VFB = 5 V 3.4
IQ Quiescent Current mA
VFB = 5 V, –40°C ≤ TJ ≤ 125°C 6
ISTDBY Standby Quiescent Current EN Pin = 0 V 25 40 µA
6.0 7.1 8.4
ICL Current Limit A
–40°C ≤ TJ ≤ 125°C 5.75 8.75
VIN = 42 V, EN Pin = 0 V, VSW = 0 V 0.2 2 µA
IL Output Leakage Current
VSW = –1 V 0.1 3 µA
0.1 0.14
RDS(ON) Switch On-Resistance Ω
–40°C ≤ TJ ≤ 125°C 0.2
500
fO Oscillator Frequency kHz
–40°C ≤ TJ ≤ 125°C 400 600
200
TOFFMIN Minimum Off-time ns
–40°C ≤ TJ ≤ 125°C 100 300
TONMIN Minimum On-time 100 ns
IBIAS Feedback Bias Current VFB = 1.3 V (ADJ Version Only) 230 nA
Falling 1.6
VEN Enable Threshold Voltage V
Falling, –40°C ≤ TJ ≤ 125°C 1.3 1.9
VENHYST Enable Voltage Hysteresis 0.6 V
IEN Enable Input Current EN Input = 0 V 6 µA
FSYNC Maximum Synchronization Frequency VSYNC = 3.5 V, 50% duty-cycle 1 MHz
VSYNC Synchronization Threshold Voltage 1.75 V
TSD Thermal Shutdown Threshold 150 °C

(1) MIN and MAX limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlation
using Statistical Quality Control (SQC) methods. Limits are used to calculate TI's Average Outgoing Quality Level (AOQL).
(2) Typical values represent most likely parametric norms at the conditions specified and are not ensured.

Copyright © 2008–2015, Texas Instruments Incorporated Submit Documentation Feedback 5

Product Folder Links: LM22677 LM22677-Q1
LM22677, LM22677-Q1
SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015 www.ti.com

6.7 Typical Characteristics

VIN = 12 V, TJ = 25°C (unless otherwise specified).

Figure 1. Efficiency vs IOUT and VIN, VOUT = 3.3 V Figure 2. Normalized Switching Frequency vs Temperature

Figure 3. Current Limit vs Temperature Figure 4. Normalized RDS(ON) vs Temperature

Figure 5. Feedback Bias Current vs Temperature Figure 6. Normalized Enable Threshold Voltage vs
Temperature

6 Submit Documentation Feedback Copyright © 2008–2015, Texas Instruments Incorporated

Product Folder Links: LM22677 LM22677-Q1

 LM22677, LM22677-Q1
www.ti.com SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015

Typical Characteristics (continued)

VIN = 12 V, TJ = 25°C (unless otherwise specified).

Figure 7. Standby Quiescent Current vs Input Voltage Figure 8. Normalized Feedback Voltage vs Temperature

Figure 9. Normalized Feedback Voltage vs Input Voltage Figure 10. Switching Frequency vs RT/SYNC Resistor

Copyright © 2008–2015, Texas Instruments Incorporated Submit Documentation Feedback 7

Product Folder Links: LM22677 LM22677-Q1
LM22677, LM22677-Q1
SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015 www.ti.com

7 Detailed Description

7.1 Overview
The LM22677 device incorporates a voltage mode constant frequency PWM architecture. In addition, input
voltage feedforward is used to stabilize the loop gain against variations in input voltage. This allows the loop
compensation to be optimized for transient performance. The power MOSFET, in conjunction with the diode,
produce a rectangular waveform at the switch pin, that swings from about zero volts to VIN. The inductor and
output capacitor average this waveform to become the regulator output voltage. By adjusting the duty cycle of
this waveform, the output voltage can be controlled. The error amplifier compares the output voltage with the
internal reference and adjusts the duty cycle to regulate the output at the desired value.
The internal loop compensation of the -ADJ option is optimized for outputs of 5 V and below. If an output voltage
of 5 V or greater is required, the -5.0 option can be used with an external voltage divider. The minimum output
voltage is equal to the reference voltage, that is, 1.285 V (typical).

7.2 Functional Block Diagram

VIN

VIN

Vcc BOOT
EN INT REG, EN,UVLO

ILimit

PWM Cmp.
- TYPE III
+ LOGIC
FB + COMP -
Error Amp.

VOUT

OSC SW

1.285V
&
Soft-Start

RT/SYNC GND

7.3 Feature Description

7.3.1 Precision Enable and UVLO
The precision enable input (EN) is used to control the regulator. The precision feature allows simple sequencing
of multiple power supplies with a resistor divider from another supply. Connecting this pin to ground or to a
voltage less than 1.6 V (typical) will turn off the regulator. The current drain from the input supply, in this state, is
25 µA (typical) at an input voltage of 12 V. The EN input has an internal pullup of about 6 µA. Therefore this pin
can be left floating or pulled to a voltage greater than 2.2 V (typical) to turn the regulator on. The hysteresis on
this input is about 0.6 V (typical) above the 1.6 V (typical) threshold. When driving the enable input, the voltage
must never exceed the 6 V absolute maximum specification for this pin.

8 Submit Documentation Feedback Copyright © 2008–2015, Texas Instruments Incorporated

Product Folder Links: LM22677 LM22677-Q1

 LM22677, LM22677-Q1
www.ti.com SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015

Feature Description (continued)

Although an internal pullup is provided on the EN pin, it is good practice to pull the input high, when this feature
is not used, especially in noisy environments. This can most easily be done by connecting a resistor between VIN
and the EN pin. The resistor is required, because the internal zener diode, at the EN pin, will conduct for
voltages above about 6 V. The current in this zener must be limited to less than 100 µA. A resistor of 470 kΩ will
limit the current to a safe value for input voltages as high 42 V. Smaller values of resistor can be used at lower
input voltages.
The LM22677 also incorporates an input undervoltage lock-out (UVLO) feature. This prevents the regulator from
turning on when the input voltage is not great enough to properly bias the internal circuitry. The rising threshold is
4.3 V (typical) while the falling threshold is 3.9 V (typical). In some cases these thresholds may be too low to
provide good system performance. The solution is to use the EN input as an external UVLO to disable the part
when the input voltage falls below a lower boundary. This is often used to prevent excessive battery discharge or
early turn-on during start-up. This method is also recommended to prevent abnormal device operation in
applications where the input voltage falls below the minimum of 4.5 V. Figure 11 shows the connections to
implement this method of UVLO. Equation 1 and Equation 2 can be used to determine the correct resistor
values.

(1)

where
• Voff is the input voltage where the regulator shuts off.
• Von is the voltage where the regulator turns on. (2)
Due to the 6 µA pullup, the current in the divider should be much larger than this. A value of 20 kΩ, for RENB is a
good first choice. Also, a zener diode may be needed between the EN pin and ground, in order to comply with
the absolute maximum ratings on this pin.
Vin

RENT

EN

RENB

Figure 11. External UVLO Connections

7.3.2 Soft-Start
The soft-start feature allows the regulator to gradually reach steady-state operation, thus reducing start-up
stresses. The internal soft-start feature brings the output voltage up in about 500 µs. This time is fixed and can
not be changed. Soft-start is reset any time the part is shut down or a thermal overload event occurs.

7.3.3 Switching Frequency Adjustment and Synchronization

The LM22677 will operate in three different modes, depending on the condition of the RT/SYNC pin. With the
RT/SYNC pin floating, the regulator will switch at the internally set frequency of 500 kHz (typ). With a resistor in
the range of 25 kΩ to 200 kΩ, connected from RT/SYNC to ground, the internal switching frequency can be
adjusted from 1 MHz to 200 kHz. Figure 12 shows the typical curve for switching frequency versus the external
resistance connected to the RT/SYNC pin. The accuracy of the switching frequency, in this mode, is slightly
worse than that of the internal oscillator; about ±25% is to be expected. Finally, an external clock can be applied
to the RT/SYNC pin to allow the regulator to synchronize to a system clock or another LM22677. The mode is
set during start-up of the regulator. When the LM22677 is enabled, or after VIN is applied, a weak pullup is
connected to the RT/SYNC pin and, after approximately 100 µs, the voltage on the pin is checked against a

Copyright © 2008–2015, Texas Instruments Incorporated Submit Documentation Feedback 9

Product Folder Links: LM22677 LM22677-Q1
LM22677, LM22677-Q1
SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015 www.ti.com

Feature Description (continued)

threshold of about 0.8 V. With the RT/SYNC pin open, the voltage floats above this threshold, and the mode is
set to run with the internal clock. With a frequency set resistor present, an internal reference holds the pin
voltage at 0.8 V; the resulting current sets the mode to allow the resistor to control the clock frequency. If the
external circuit forces the RT/SYNC pin to a voltage much greater or less than 0.8 V, the mode is set to allow
external synchronization. The mode is latched until either the EN or the input supply is cycled.
The choice of switching frequency is governed by several considerations. As an example, lower frequencies may
be desirable to reduce switching losses or improve duty cycle limits. Higher frequencies, or a specific frequency,
may be desirable to avoid problems with EMI or reduce the physical size of external components. The flexibility
of increasing the switching frequency above 500 kHz can also be used to operate outside a critical signal
frequency band for a given application. Keep in mind that the values of inductor and output capacitor cannot be
reduced dramatically, by operating above 500 kHz. This is true because the design of the internal loop
compensation restricts the range of these components.
Frequency synchronization requires some care. First the external clock frequency must be greater than the
internal clock frequency, and less than 1 MHz. The maximum internal switching frequency is specified in the
Electrical Characteristics table.

NOTE
The frequency adjust feature and the synchronization feature can not be used
simultaneously.

The synchronizing frequency must always be greater than the internal clock frequency. Secondly, the RT/SYNC
pin must see a valid high or low voltage, during start-up, in order for the regulator to go into the synchronizing
mode (see above). Also, the amplitude of the synchronizing pulses must comport with VSYNC levels found in the
Electrical Characteristics table. The regulator will synchronize on the rising edge of the external clock. If the
external clock is lost during normal operation, the regulator will revert to the 500 kHz (typical) internal clock.
If the frequency synchronization feature is used, current limit foldback is not operational (see the Current Limit
section for details).

Figure 12. Switching Frequency vs RT/SYNC Resistor

10 Submit Documentation Feedback Copyright © 2008–2015, Texas Instruments Incorporated

Product Folder Links: LM22677 LM22677-Q1

 LM22677, LM22677-Q1
www.ti.com SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015

Feature Description (continued)

7.3.4 Self Synchronization
It is possible to synchronize multiple LM22677 regulators together to share the same switching frequency. This
can be done by tying the RT/SYNC pins together through a MOSFET and connecting a 1 kΩ resistor to ground
at each pin. Figure 13 shows this connection. The gate of the MOSFET should be connected to the regulator
with the highest output voltage. Also, the EN pins of both regulators should be tied to the common system
enable, in order to properly initialize both regulators. The operation is as follows: When the regulators are
enabled, the outputs are low and the MOSFET is off. The 1 kΩ resistors pull the RT/SYNC pins low, thus
enabling the synchronization mode. These resistors are small enough to pull the RT/SYNC pin low, rather than
activate the frequency adjust mode. Once the output voltage of one of the regulators is sufficient to turn on the
MOSFET, the two RT/SYNC pins are tied together and the regulators will run in synchronization mode. The two
regulators will be clocked at the same frequency but slightly phase shifted according to the minimum off-time of
the regulator with the fastest internal oscillator. The slight phase shift helps to reduce stress on the input
capacitors of the regulator. It is important to choose a MOSFET with a low gate threshold voltage so that the
MOSFET will be fully enhanced. Also, a MOSFET with low inter-electrode capacitance is required. The 2N7002
is a good choice.

ENABLE
EN EN

LM22677 LM22677

RT/SYNC RT/SYNC

2N7002

1k 1k
Vout

Figure 13. Self Synchronizing Setup

7.3.5 Boot-Strap Supply

The LM22677 incorporates a floating high-side gate driver to control the power MOSFET. The supply for this
driver is the external boot-strap capacitor connected between the BOOT pin and SW. A good quality 10 nF
ceramic capacitor must be connected to these pins with short, wide PCB traces. One reason the regulator
imposes a minimum off-time is to ensure that this capacitor recharges every switching cycle. A minimum load of
about 5 mA is required to fully recharge the boot-strap capacitor in the minimum off-time. Some of this load can
be provided by the output voltage divider, if used.

7.3.6 Internal Compensation

The LM22677 has internal loop compensation designed to provide a stable regulator over a wide range of
external power stage components. The internal compensation of the -ADJ option is optimized for output voltages
below 5 V. If an output voltage of 5 V or greater is needed, the -5.0 option with an external resistor divider can be
used.
Ensuring stability of a design with a specific power stage (inductor and output capacitor) can be tricky. The
LM22677 stability can be verified using the WEBENCH Designer online circuit simulation tool. A quick start
spreadsheet can also be downloaded from the online product folder.
The complete transfer function for the regulator loop is found by combining the compensation and power stage
transfer functions. The LM22677 has internal type III loop compensation, as detailed in Figure 14. This is the
approximate "straight line" function from the FB pin to the input of the PWM modulator. The power stage transfer
function consists of a dc gain and a second order pole created by the inductor and output capacitor(s). Due to
the input voltage feedforward employed in the LM22677, the power stage dc gain is fixed at 20 dB. The second
order pole is characterized by its resonant frequency and its quality factor (Q). For a first pass design, the
product of inductance and output capacitance should conform to Equation 3.

(3)

Copyright © 2008–2015, Texas Instruments Incorporated Submit Documentation Feedback 11

Product Folder Links: LM22677 LM22677-Q1
LM22677, LM22677-Q1
SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015 www.ti.com

Feature Description (continued)

Alternatively, this pole should be placed between 1.5 kHz and 15 kHz and is given by Equation 4.

(4)
The Q factor depends on the parasitic resistance of the power stage components and is not typically in the
control of the designer. Of course, loop compensation is only one consideration when selecting power stage
components (see the Applications and Implementation section for more details).
40
-ADJ
-5.0
35

COMPENSATOR GAIN (dB)

30

25

20

15

10

0
100 1k 10k 100k 1M 10M
FREQUENCY (Hz)

Figure 14. Compensator Gain

In general, hand calculations or simulations can only aid in selecting good power stage components. Good
design practice dictates that load and line transient testing should be done to verify the stability of the application.
Also, Bode plot measurements should be made to determine stability margins. AN-1889 How to Measure the
Loop Transfer Function of Power Supplies (SNVA364) shows how to perform a loop transfer function
measurement with only an oscilloscope and function generator.

7.4 Device Functional Modes

7.4.1 Current Limit
The LM22677 has current limiting to prevent the switch current from exceeding safe values during an accidental
overload on the output. This peak current limit is found in the Electrical Characteristics table under the heading of
ICL. The maximum load current that can be provided, before current limit is reached, is determined from
Equation 5.

where
• L is the value of the power inductor. (5)
When the LM22677 enters current limit, the output voltage will drop and the peak inductor current will be fixed at
ICL at the end of each cycle. The switching frequency will remain constant while the duty cycle drops. The load
current will not remain constant, but will depend on the severity of the overload and the output voltage.
For very severe overloads ("short-circuit"), the regulator changes to a low frequency current foldback mode of
operation. The frequency foldback is about 1/5 of the nominal switching frequency. This will occur when the
current limit trips before the minimum on-time has elapsed. This mode of operation is used to prevent inductor
current "run-away", and is associated with very low output voltages when in overload. Equation 6 can be used to
determine what level of output voltage will cause the part to change to low frequency current foldback.

12 Submit Documentation Feedback Copyright © 2008–2015, Texas Instruments Incorporated

Product Folder Links: LM22677 LM22677-Q1

 LM22677, LM22677-Q1
www.ti.com SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015

Device Functional Modes (continued)

where
• Fsw is the normal switching frequency.
• Vin is the maximum for the application. (6)
If the overload drives the output voltage to less than or equal to Vx, the device will enter current foldback mode. If
a given application can drive the output voltage to ≤Vx, during an overload, then a second criterion must be
checked. Equation 7 gives the maximum input voltage, when in this mode, before damage occurs:

where
• Vsc is the value of output voltage during the overload.
• Fsw is the normal switching frequency. (7)

NOTE
If the input voltage should exceed this value while in foldback mode, the regulator and/or
the diode may be damaged.

It is important to note that the voltages in these equations are measured at the inductor. Normal trace and wiring
resistance will cause the voltage at the inductor to be higher than that at a remote load. Therefore, even if the
load is shorted with zero volts across its terminals, the inductor will still see a finite voltage. It is this value that
should be used for Vx and Vsc in the calculations. In order to return from foldback mode, the load must be
reduced to a value much lower than that required to initiate foldback. This load "hysteresis" is a normal aspect of
any type of current limit foldback associated with voltage regulators.
If the frequency synchronization feature is used, the current limit frequency fold-back is not operational, and the
system may not survive a hard short-circuit at the output.
The safe operating areas, when in short circuit mode, are shown in Figure 15 through Figure 17, for different
switching frequencies. Operating points below and to the right of the curve represent safe operation.

NOTE
Figure 15, Figure 16, and Figure 17 curves are not valid when the LM22677 is in
frequency synchronization mode.

45 45

40 40

35 35
INPUT VOLTAGE (v)
INPUT VOLTAGE (v)

30 30
SAFE OPERATING AREA
25 25 SAFE OPERATING AREA

20 20

15 15

10 10

5 5
0.0 0.2 0.4 0.6 0.8 1.0 1.2 0.0 0.2 0.4 0.6 0.8 1.0 1.2
SHORT CIRCUIT VOLTAGE (v) SHORT CIRCUIT VOLTAGE (v)

Figure 15. SOA at 300 kHz Figure 16. SOA at 500 kHz

Copyright © 2008–2015, Texas Instruments Incorporated Submit Documentation Feedback 13

Product Folder Links: LM22677 LM22677-Q1
LM22677, LM22677-Q1
SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015 www.ti.com

Device Functional Modes (continued)

45

40

35

INPUT VOLTAGE (v)

30

25

20 SAFE OPERATING AREA

15

10

5
0.0 0.2 0.4 0.6 0.8 1.0 1.2
SHORT CIRCUIT VOLTAGE (v)

Figure 17. SOA at 800 kHz

7.4.2 Thermal Protection

Internal thermal shutdown circuitry protects the LM22677 should the maximum junction temperature be
exceeded. This protection is activated at about 150°C, with the result that the regulator will shut down until the
temperature drops below about 135°C.

7.4.3 Duty-Cycle Limits

Ideally the regulator would control the duty cycle over the full range of zero to one. However, due to inherent
delays in the circuitry, there are limits on both the maximum and minimum duty cycles that can be reliably
controlled. This in turn places limits on the maximum and minimum input and output voltages that can be
converted by the LM22677. A minimum on-time is imposed by the regulator in order to correctly measure the
switch current during a current limit event. A minimum off-time is imposed in order the re-charge the bootstrap
capacitor. Equation 8 can be used to determine the approximate maximum input voltage for a given output
voltage.

where
• Fsw is the switching frequency.
• TON is the minimum on-time. (8)
If the frequency adjust feature is used, that value should be used for Fsw. Nominal values should be used. The
worst case is lowest output voltage, and highest switching frequency. If this input voltage is exceeded, the
regulator will skip cycles, effectively lowering the switching frequency. The consequences of this are higher
output voltage ripple and a degradation of the output voltage accuracy.
The second limitation is the maximum duty cycle before the output voltage will "dropout" of regulation. Equation 9
can be used to approximate the minimum input voltage before dropout occurs.

where
• The values of TOFF and RDS(ON) are found in the Electrical Characteristics table. (9)
The worst case here is highest switching frequency and highest load. In Equation 9, RL is the dc inductor
resistance. Of course, the lowest input voltage to the regulator must not be less than 4.5 V (typical).

14 Submit Documentation Feedback Copyright © 2008–2015, Texas Instruments Incorporated

Product Folder Links: LM22677 LM22677-Q1

 LM22677, LM22677-Q1
www.ti.com SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015

8 Applications and Implementation

NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.

8.1 Application Information

The LM22677 is a step-down dc-to-dc regulator. It is typically used to convert a higher dc voltage to a lower dc
voltage with a maximum output current of 5 A. The Detailed Design Procedure can be used to select
components for the LM22677. Alternately, the WEBENCH software may be used to generate complete designs.
When generating a design, the WEBENCH software utilizes iterative design procedures and accesses
comprehensive databases of components. Go to WEBENCH Designer for more details.

8.1.1 Output Voltage Divider Selection

For output voltages between about 1.285 V and 5 V, the -ADJ option should be used, with an appropriate voltage
divider as shown in Figure 18. Equation 10 can be used to calculate the resistor values of this divider:

(10)
A good value for RFBB is 1 kΩ. This will help to provide some of the minimum load current requirement and
reduce susceptibility to noise pick-up. The top of RFBT should be connected directly to the output capacitor or to
the load for remote sensing. If the divider is connected to the load, a local high-frequency bypass should be
provided at that location.
For output voltages of 5 V, the -5.0 option should be used. In this case no divider is needed and the FB pin is
connected to the output. The approximate values of the internal voltage divider are as follows: 7.38 kΩ from the
FB pin to the input of the error amplifier and 2.55 kΩ from there to ground.
Both the -ADJ and -5.0 options can be used for output voltages greater than 5 V, by using the correct output
divider. As mentioned in the Internal Compensation section, the -5.0 option is optimized for output voltages of 5
V. However, for output voltages greater than 5 V, this option may provide better loop bandwidth than the
-ADJ option, in some applications. If the -5.0 option is to be used at output voltages greater than 5 V,
Equation 11 should be used to determine the resistor values in the output divider.

(11)
A value of RFBB of about 1 kΩ is a good first choice.
Vout

RFBT

FB

RFBB

Figure 18. Resistive Feedback Divider

A maximum value of 10 kΩ is recommended for the sum of RFBB and RFBT to maintain good output voltage
accuracy for the -ADJ option. A maximum of 2 kΩ is recommended for the -5.0 option. For the -5.0 option, the
total internal divider resistance is typically 9.93 kΩ.
In all cases the output voltage divider should be placed as close as possible to the FB pin of the LM22677,
because this is a high impedance input and is susceptible to noise pick-up.
Copyright © 2008–2015, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM22677 LM22677-Q1
LM22677, LM22677-Q1
SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015 www.ti.com

Application Information (continued)

8.1.2 Power Diode
A Schottky-type power diode is required for all LM22677 applications. Ultra-fast diodes are not recommended
and may result in damage to the IC due to reverse recovery current transients. The near ideal reverse recovery
characteristics and low forward voltage drop of Schottky diodes are particularly important for high input voltage
and low output voltage applications common to the LM22677. The reverse breakdown rating of the diode should
be selected for the maximum VIN, plus some safety margin. A good rule of thumb is to select a diode with a
reverse voltage rating of 1.3 times the maximum input voltage.
Select a diode with an average current rating at least equal to the maximum load current that will be seen in the
application.

8.2 Typical Application

Figure 19 shows an example of converting an input voltage range of 5.5 V to 42 V to an output of 3.3 V at 5 A.
RFBB
VIN 4.5V to 42V 976:
VIN FB
C3
LM22677-ADJ 10 nF
EN
RFBT
EN BOOT L1
1.54 k:
SYNC 4.7 PH
C2 + C1 C7
RT/SYNC SW VOUT 3.3V
22 PF 6.8 PF 6.8 PF GND
D1 C4 +
R3 60V, 5A 180 PF

GND GND

Figure 19. Typical Buck Regulator Application

8.2.1 Design Requirements

DESIGN PARAMETERS EXAMPLE VALUE

Driver Supply Voltage (VIN) 4.5 to 42 V
Output Voltage (VOUT) 3.3 V
RFBT Calculated based on RFBB and VREF of 1.285 V.
RFBB 1 kΩ to 10 kΩ
IOUT 5A

8.2.2 Detailed Design Procedure

8.2.2.1 External Components

The following guidelines should be used when designing a step-down (buck) converter with the LM22677.

8.2.2.2 Inductor
The inductor value is determined based on the load current, ripple current, and the minimum and maximum input
voltages. To keep the application in continuous conduction mode (CCM), the maximum ripple current, IRIPPLE,
should be less than twice the minimum load current.
The general rule of keeping the inductor current peak-to-peak ripple around 30% of the nominal output current is
a good compromise between excessive output voltage ripple and excessive component size and cost. Using this
value of ripple current, the value of inductor, L, is calculated using Equation 12.

where

16 Submit Documentation Feedback Copyright © 2008–2015, Texas Instruments Incorporated

Product Folder Links: LM22677 LM22677-Q1

 LM22677, LM22677-Q1
www.ti.com SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015

• Fsw is the switching frequency.

• Vin should be taken at its maximum value, for the given application. (12)
The formula in Equation 12 provides a guide to select the value of the inductor L; the nearest standard value will
then be used in the circuit.
Once the inductor is selected, the actual ripple current can be found from Equation 13.

(13)
Increasing the inductance will generally slow down the transient response but reduce the output voltage ripple.
Reducing the inductance will generally improve the transient response but increase the output voltage ripple.
The inductor must be rated for the peak current, IPK, in a given application, to prevent saturation. During normal
loading conditions, the peak current is equal to the load current plus 1/2 of the inductor ripple current.
During an overload condition, as well as during certain load transients, the controller may trip current limit. In this
case the peak inductor current is given by ICL, found in the Electrical Characteristics table. Good design practice
requires that the inductor rating be adequate for this overload condition.

NOTE
If the inductor is not rated for the maximum expected current, it can saturate resulting in
damage to the LM22677 and/or the power diode.

8.2.2.3 Input Capacitor

The input capacitor selection is based on both input voltage ripple and RMS current. Good quality input
capacitors are necessary to limit the ripple voltage at the VIN pin while supplying most of the regulator current
during switch on-time. Low ESR ceramic capacitors are preferred. Larger values of input capacitance are
desirable to reduce voltage ripple and noise on the input supply. This noise may find its way into other circuitry,
sharing the same input supply, unless adequate bypassing is provided. A very approximate formula for
determining the input voltage ripple is shown in Equation 14.

where
• Vri is the peak-to-peak ripple voltage at the switching frequency. (14)
Another concern is the RMS current passing through this capacitor. Equation 15 gives an approximation to this
current.

(15)
The capacitor must be rated for at least this level of RMS current at the switching frequency.
All ceramic capacitors have large voltage coefficients, in addition to normal tolerances and temperature
coefficients. To help mitigate these effects, multiple capacitors can be used in parallel to bring the minimum
capacitance up to the desired value. This may also help with RMS current constraints by sharing the current
among several capacitors. Many times it is desirable to use an electrolytic capacitor on the input, in parallel with
the ceramics. The moderate ESR of this capacitor can help to damp any ringing on the input supply caused by
long power leads. This method can also help to reduce voltage spikes that may exceed the maximum input
voltage rating of the LM22677.
It is good practice to include a high frequency bypass capacitor as close as possible to the LM22677. This small
case size, low ESR, ceramic capacitor should be connected directly to the VIN and GND pins with the shortest
possible PCB traces. Values in the range of 0.47 µF to 1 µF are appropriate. This capacitor helps to provide a
low impedance supply to sensitive internal circuitry. It also helps to suppress any fast noise spikes on the input
supply that may lead to increased EMI.

Copyright © 2008–2015, Texas Instruments Incorporated Submit Documentation Feedback 17

Product Folder Links: LM22677 LM22677-Q1
LM22677, LM22677-Q1
SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015 www.ti.com

8.2.2.4 Output Capacitor

The output capacitor is responsible for filtering the output voltage and supplying load current during transients.
Capacitor selection depends on application conditions as well as ripple and transient requirements. Best
performance is achieved with a parallel combination of ceramic capacitors and a low ESR SP™ or POSCAP™
type. Very low ESR capacitors such as ceramics reduce the output ripple and noise spikes, while higher value
electrolytics or polymers provide large bulk capacitance to supply transients. Assuming very low ESR,
Equation 16 gives an approximation to the output voltage ripple:

(16)
Typically, a total value of 100 µF or greater is recommended for output capacitance.
In applications with Vout less than 3.3 V, it is critical that low ESR output capacitors are selected. This will limit
potential output voltage overshoots as the input voltage falls below the device normal operating range.
If the switching frequency is set higher than 500 kHz, the capacitance value may not be reduced proportionally
due to stability requirements. The internal compensation is optimized for circuits with a 500 kHz switching
frequency. See the Internal Compensation section for more details.

8.2.2.5 Boot-Strap Capacitor

The bootstrap capacitor between the BOOT pin and the SW pin supplies the gate current to turn on the N-
channel MOSFET. The recommended value of this capacitor is 10 nF and should be a good quality, low ESR
ceramic capacitor.
In some cases it may be desirable to slow down the turn-on of the internal power MOSFET, in order to reduce
EMI. This can be done by placing a small resistor in series with the Cboot capacitor. Resistors in the range of 10
Ω to 50 Ω can be used. This technique should only be used when absolutely necessary, because it will increase
switching losses and thereby reduce efficiency.

8.2.3 Application Curves

Figure 20. Efficiency vs IOUT and VIN, VOUT = 3.3 V Figure 21. Switching Frequency vs RT/SYNC Resistor

18 Submit Documentation Feedback Copyright © 2008–2015, Texas Instruments Incorporated

Product Folder Links: LM22677 LM22677-Q1

 LM22677, LM22677-Q1
www.ti.com SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015

9 Power Supply Recommendations

The LM22677 is designed to operate from an input voltage supply range between 4.5 V and 42 V. This input
supply should be able to withstand the maximum input current and maintain a voltage above 4.5 V. The
resistance of the input supply rail should be low enough that an input current transient does not cause a high
enough drop at the LM22677 supply voltage that can cause a false UVLO fault triggering and system reset.
If the input supply is located more than a few inches from the LM22677 additional bulk capacitance may be
required in addition to the ceramic bypass capacitors. The amount of bulk capacitance is not critical, but a 47 µF
or 100 µF electrolytic capacitor is a typical choice.

10 Layout

10.1 Layout Guidelines

Board layout is critical for the proper operation of switching power supplies. First, the ground plane area must be
sufficient for thermal dissipation purposes. Second, appropriate guidelines must be followed to reduce the effects
of switching noise. Switch mode converters are very fast switching devices. In such cases, the rapid increase of
input current combined with the parasitic trace inductance generates unwanted L di/dt noise spikes. The
magnitude of this noise tends to increase as the output current increases. This noise may turn into
electromagnetic interference (EMI) and can also cause problems in device performance. Therefore, care must be
taken in layout to minimize the effect of this switching noise.
The most important layout rule is to keep the ac current loops as small as possible. Figure 22 shows the current
flow in a buck converter. The top schematic shows a dotted line which represents the current flow during the FET
switch on-state. The middle schematic shows the current flow during the FET switch off-state.
The bottom schematic shows the currents referred to as ac currents. These ac currents are the most critical
because they are changing in a very short time period. The dotted lines of the bottom schematic are the traces to
keep as short and wide as possible. This will also yield a small loop area reducing the loop inductance. To avoid
functional problems due to layout, review the PCB layout example. Best results are achieved if the placement of
the LM22677, the bypass capacitor, the Schottky diode, RFBB, RFBT and the inductor are placed as shown in the
example. Note that, in the layout shown, R1 = RFBB and R2 = RFBT. It is also recommended to use 2-oz copper
boards or heavier to help thermal dissipation and to reduce the parasitic inductances of board traces. See
application note AN-1229 SIMPLE SWITCHER ® PCB Layout Guidelines (SNVA054) for more information.

Figure 22. Current Flow in a Buck Application

Copyright © 2008–2015, Texas Instruments Incorporated Submit Documentation Feedback 19

Product Folder Links: LM22677 LM22677-Q1
LM22677, LM22677-Q1
SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015 www.ti.com

10.2 Layout Example

Figure 23. PCB Layout Example

20 Submit Documentation Feedback Copyright © 2008–2015, Texas Instruments Incorporated

Product Folder Links: LM22677 LM22677-Q1

 LM22677, LM22677-Q1
www.ti.com SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015

10.3 Thermal Considerations

The components with the highest power dissipation are the power diode and the power MOSFET internal to the
LM22677 regulator. The easiest method to determine the power dissipation within the LM22677 is to measure
the total conversion losses then subtract the power losses in the diode and inductor. The total conversion loss is
the difference between the input power and the output power. An approximation for the power diode loss is in
Equation 17.

where
• VD is the diode voltage drop. (17)
An approximation for the inductor power is shown in Equation 18.

where
• RL is the dc resistance of the inductor.
• The 1.1 factor is an approximation for the ac losses. (18)
The regulator has an exposed thermal pad to aid power dissipation. Adding multiple vias under the device to the
ground plane will greatly reduce the regulator junction temperature. Selecting a diode with an exposed pad will
also aid the power dissipation of the diode. The most significant variables that affect the power dissipation of the
regulator are output current, input voltage and operating frequency. The power dissipated while operating near
the maximum output current and maximum input voltage can be appreciable. The junction-to-ambient thermal
resistance of the LM22677 will vary with the application. The most significant variables are the area of copper in
the PC board, the number of vias under the IC exposed pad and the amount of forced air cooling provided. A
large continuos ground plane on the top of bottom PCB layer will provide the most effective heat dissipation. The
integrity of the solder connection from the IC exposed pad to the PC board is critical. Excessive voids will greatly
diminish the thermal dissipation capacity. The junction-to-ambient thermal resistance of the LM22677 NDR
package is specified in the Electrical Characteristics table. See AN-2020 Thermal Design By Insight, Not
Hindsight (SNVA419) for more information.

Copyright © 2008–2015, Texas Instruments Incorporated Submit Documentation Feedback 21

Product Folder Links: LM22677 LM22677-Q1
LM22677, LM22677-Q1
SNVS582O – SEPTEMBER 2008 – REVISED AUGUST 2015 www.ti.com

11 Device and Documentation Support

11.1 Documentation Support

11.1.1 Related Documentation
• AN-1889 How to Measure the Loop Transfer Function of Power Supplies (SNVA364)
• AN-1892 LM22677 Evaluation Board (SNVA366)
• AN-1229 SIMPLE SWITCHER ® PCB Layout Guidelines (SNVA054)
• AN-2020 Thermal Design By Insight, Not Hindsight (SNVA419)

11.2 Related Links

The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.

Table 1. Related Links

TECHNICAL TOOLS & SUPPORT &
PARTS PRODUCT FOLDER SAMPLE & BUY
DOCUMENTS SOFTWARE COMMUNITY
LM22677 Click here Click here Click here Click here Click here
LM22677-Q1 Click here Click here Click here Click here Click here

11.3 Trademarks
SIMPLE SWITCHER, WEBENCH are registered trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.

11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.

12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

22 Submit Documentation Feedback Copyright © 2008–2015, Texas Instruments Incorporated

Product Folder Links: LM22677 LM22677-Q1

 PACKAGE OPTION ADDENDUM

www.ti.com 8-Oct-2015

PACKAGING INFORMATION

Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)

LM22677QTJ-ADJ/NOPB ACTIVE TO-263 NDR 7 1000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LM22677
& no Sb/Br) QTJ-ADJ
LM22677QTJE-5.0/NOPB ACTIVE TO-263 NDR 7 250 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LM22677
& no Sb/Br) QTJ-5.0
LM22677QTJE-ADJ/NOPB ACTIVE TO-263 NDR 7 250 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LM22677
& no Sb/Br) QTJ-ADJ
LM22677TJ-5.0/NOPB ACTIVE TO-263 NDR 7 1000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LM22677
& no Sb/Br) TJ-5.0
LM22677TJ-ADJ/NOPB ACTIVE TO-263 NDR 7 1000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LM22677
& no Sb/Br) TJ-ADJ
LM22677TJE-5.0/NOPB ACTIVE TO-263 NDR 7 250 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LM22677
& no Sb/Br) TJ-5.0
LM22677TJE-ADJ/NOPB ACTIVE TO-263 NDR 7 250 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LM22677
& no Sb/Br) TJ-ADJ

(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)

(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

Addendum-Page 1
 PACKAGE OPTION ADDENDUM

www.ti.com 8-Oct-2015

(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.

(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

OTHER QUALIFIED VERSIONS OF LM22677, LM22677-Q1 :

• Catalog: LM22677
• Automotive: LM22677-Q1

NOTE: Qualified Version Definitions:

• Catalog - TI's standard catalog product

• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects

Addendum-Page 2
 PACKAGE MATERIALS INFORMATION

www.ti.com 2-Sep-2015

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM22677QTJ-ADJ/NOPB TO-263 NDR 7 1000 330.0 24.4 10.6 15.4 2.45 12.0 24.0 Q2
LM22677QTJE-5.0/NOPB TO-263 NDR 7 250 178.0 24.4 10.6 15.4 2.45 12.0 24.0 Q2
LM22677QTJE-ADJ/NOP TO-263 NDR 7 250 178.0 24.4 10.6 15.4 2.45 12.0 24.0 Q2
B
LM22677TJ-5.0/NOPB TO-263 NDR 7 1000 330.0 24.4 10.6 15.4 2.45 12.0 24.0 Q2
LM22677TJ-ADJ/NOPB TO-263 NDR 7 1000 330.0 24.4 10.6 15.4 2.45 12.0 24.0 Q2
LM22677TJE-5.0/NOPB TO-263 NDR 7 250 178.0 24.4 10.6 15.4 2.45 12.0 24.0 Q2
LM22677TJE-ADJ/NOPB TO-263 NDR 7 250 178.0 24.4 10.6 15.4 2.45 12.0 24.0 Q2

Pack Materials-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 2-Sep-2015

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM22677QTJ-ADJ/NOPB TO-263 NDR 7 1000 367.0 367.0 35.0
LM22677QTJE-5.0/NOPB TO-263 NDR 7 250 210.0 185.0 35.0
LM22677QTJE-ADJ/NOPB TO-263 NDR 7 250 210.0 185.0 35.0
LM22677TJ-5.0/NOPB TO-263 NDR 7 1000 367.0 367.0 35.0
LM22677TJ-ADJ/NOPB TO-263 NDR 7 1000 367.0 367.0 35.0
LM22677TJE-5.0/NOPB TO-263 NDR 7 250 210.0 185.0 35.0
LM22677TJE-ADJ/NOPB TO-263 NDR 7 250 210.0 185.0 35.0

Pack Materials-Page 2
 MECHANICAL DATA
NDR0007A

BOTTOM SIDE OF PACKAGE

TOP SIDE OF PACKAGE

TJ7A (Rev D)

www.ti.com
 IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated