CURVED GAMING MONITOR

USER MANUAL
VIOTEK

Read and observe the following warnings and information below.

Safety Precautions and Maintenance

1. Before cleaning, always unplug your monitor. It is recommended to use dry

cloth or lightly damp cloth to clean your monitor. Dry cloth is, however, the
safest. If using damp cloth, wait for your monitor to completely dry before
plugging it in again.
2. Do not use alcohol or ammonia-based cleaner and/or liquids to clean your
monitor.
3. This monitor features ventilation openings on the back of the unit. Avoid
blocking these openings to prevent the monitor from overheating.
4. Avoid placing this monitor near any heat sources e.g: portable heaters or
heating vents, as this may cause damage to your monitor.
5. Do not spray cleaner and or any kind of liquid directly onto the monitor's screen
or any part of the monitor.
6. Do not insert anything into any part of the monitor especially the ventilation
openings.
7. Always make sure your monitor is placed on a secure, level surface to
prevent it from falling and sustaining damage.
8. Unplug your monitor during any extended periods of non-use.
9. Do not place heavy items on the monitor or monitor cables.
10. Do not attempt to dissemble the monitor or remove parts from monitor.
Any disassembly or modification etc. not performed by an authorized
technician can result in damage to the monitor and/or possible exposure to
high voltage electricity which may lead to serious injury or death.

Viotek shall not be held responsible for injury or damage of products or persons
due to failure to adhere to the aforementioned precautions or any others noted
hereafter.

All specifications and informations are subject to change without notice.

-1-
Box Contents
1x Monitor
1x Power Cable (AC 100-240V 50/60Hz)
1x HDMI Cable
1x User manual

Basic Setup
1. Insert one end of the VGA video cable into your PC's graphics card. DVI, HDMI, or
display port (DP) may also be used. These cables are not included.
Note: For optimal refresh rate (or "performance") at 144hrz, it is recommended to
use a Display Port (DP) or DVI-D dual link cable with the monitor's corresponding
connector.
2. Connect the other end of the video cable to the corresponding connector on
your monitor. See the image below.

DVI Connector HDMI Connector DP Connector AC IN Connector

Connectors in this graphic are not to scale. Also the small numbers inside the DVI and HDMI graphics can
be removed.

3. Connect the power cable to your monitor then connect the other end to your
power source such as a wall outlet or surge protector. It is recommended to
use a surge protector.
4. Locate the power button on the monitor and press it to turn the monitor on.
Note: If you cannot locate the power button, please refer to the Control Panel
Section on the next page.

If desired, you can use the monitor's FreeSync feature. The feature itself is on by
default. In order to use this feature, please note you must have hardware with
FreeSync capability, a DP, and the latest graphic drivers. To use FreeSync, connect
the appropriate cable to the DP connectors on both the computer and the monitor.
After connecting, you will receive a prompt to enable FreeSync on your computer.
Indicator Light
This light is located on the front of the monitor. Indicator Light

Solid blue light indicates power is on and the monitor is operating normally.
Flashing blue light indicates no video source has been detected. Please ensure your
PC is on and all video cables are fully inserted and/or connected.
All specifications and informations are subject to change without notice.

-2-
Control Panel
The Control Panel is located at the corner of the monitor. Its labels are on the front
of the monitor while its buttons are directly under the labels on the bottom
edge. The Control Panel is used (1) to turn the monitor on and (2) in combination
with the On-Screen Display (OSD) Menu to adjust the monitor settings. Review the
images below for information about this panel.

Menu/Enter Down Up Exit Power ON/OFF

Menu/Exit: Opens the main menu. And exits the current menu
screen and returns to the main menu, or closes the menu if
currently on the main menu screen
Down: Moves down/lower while navigating
Up: Moves up/higher while navigating
Enter: Enters to the selective menu screen
Power: Turns the monitor on or off

Note: The Down and Up buttons may be mapped to keyboard hotkeys if desired.

OSD Menu
The On-Screen Display (OSD) Menu may be used to adjust your monitor's settings
and appears on screen after turning on the monitor and pressing the Control
Panel's Menu/Enter Key.

Note: When using the monitor for the first time, settings will automatically adjust
to optimal settings according to your computer's configuration and parts etc.

All specifications and informations are subject to change without notice.

-3-
Adjustment Settings
Main Main Main
Main Menu Menu Submenu Menu Submenu Menu
Item Item Options Description
Icon Icon Icon
Brightness NONE NONE NONE NONE Adjust brightness
Contrast NONE NONE NONE NONE Adjust contrast
On NONE NONE Start dynamic contrast
Off NONE NONE Close dynamic contrast
DCR
Return NONE NONE Return to previous menu
Exit NONE NONE Exit the menu
Standard NONE NONE Adjust settings to default
Optimize settings for
Movie NONE NONE
watching movies
FPS NONE NONE FPS games settings
Mode RTS NONE NONE RTS games settings
Optimize settings to
EyeSaver NONE NONE
reduce eye strain
Return NONE NONE Return to previous menu
Exit NONE NONE Exit the menu
Cool NONE NONE Set cool temperature
Warm NONE NONE Set warm temperature
Adjust red color
Red
temperature
Colo Adjust green color
User Green
Temperature temperature
Adjust blue color
Blue
temperature
Return NONE NONE Return to previous menu
Exit NONE NONE Exit the menu
Automatically adjust the
Auto NONE NONE
image ratio
Adjust image for widescreen
16:9 NONE NONE
ratio
Aspect
Ratio 4:3 NONE NONE Adjust image for 4:3 ratio
Return NONE NONE Return to previous menu
Exit NONE NONE Exit the menu
DVI NONE NONE DVI signal input
HDMI NONE NONE HDMI signal input
Dispay port (DP) signal
Input DP NONE NONE
input
Return NONE NONE Return to previous menu
Exit NONE NONE Exit the menu

All specifications and informations are subject to change without notice.

-4-
 Main Main Main
Main Menu Menu Submenu Menu Submenu Menu
Item Item Options Description
Icon Icon Icon
Automatically adjusts the
Auto flicker in screen, display
NONE NONE
Adjust position, size and resolution

Auto
NONE NONE Adjust white color balance
Color
Adjust Adjust tone brightness , Gray
Gamma1
level 1
Adjust tone brightness , Gray
Gamma Gamma2
level 2
Return Return to previous menu
Exit Exit the menu
Chinese Chinese
English English
Language
Return Return to previous menu

Exit Exit the menu

Power saving after minute
On ON
and auto power-off
Power Off Turn off auto power-off
Off
Return Return to previous menu
Exit Exit the menu
YES Restore Factory Defaults
Other NO Exit the function
Reset
Return Return to previous menu
Exit Exit the menu
Start OD function (requires
On ON
monitor support)
Over Close OD function (requires
Off
driver monitor support)
Return Return to previous menu
Exit Exit the menu
Only available on supported
SOUND NONE NONE
model
Return NONE NONE Return to previous menu
Exit NONE NONE Exit the menu
Exit NONE NONE NONE NONE Exit the menu

All specifications and informations are subject to change without notice.

-5-
Troubleshooting
1. The screen is blank.
- Be sure the power button has been pressed to turn the monitor on.
- Confirm the brightness and contrast settings are set normally.
- Check if the Indicator Light is flashing, if so, this indicates there is no signal
from your video source.
- If your source is a notebook or laptop, be sure that its settings are in mirror
mode and the device itself is powered on.

2. The image is out of focus.

- Ensure the video cable is inserted properly on both ends.

3. The screen is flashing.

- Try an alternative power source. If the current one is insufficient, it may be
causing this issue.
- Ensure devices such as non-shielded speakers, fluorescent lighting, AC
transformers, table fans etc. are a safe distance away from your screen to avoid
magnetic disturbances.
- Press the Exit button on the monitor to auto adjust the image and apply
optimal settings.

4. The color bleeds or visual effects appear unusual.

- If your screen is all red, blue, or any colors disappear, check to see that the
cable is properly inserted. A loose connection can cause a bad signal.
- Try connecting to another video source for comparison.

5. The screen appears to be scrolling or rolling or moving unusually.

- Check that your source frequency is within 55-76Hz.
- Reconnect and ensure your video source cable is secure.

6. The monitor needs cleaning.

- Make sure the monitor has been powered off before cleaning.
- Always use a soft, non-abrasive cloth when cleaning.
- Use dry, non-abrasive cloth to gently remove debris or dust.
- If necessary, lightly dampen a non-abrasive cloth with water and gently clean
the surface.
- Never use alcohol or ammonia-based cleaning solutions.
- Never spray liquid directly onto any part of the monitor.

All specifications and informations are subject to change without notice.

-6-
Specifications
Panel Diagonal Picture Size Dot Pitch Optimal
Screen Ratio
S ize (mm) (mm) Resolution
27in (68.6cm) 16:9 597.9*336.3 0.3114 1920x1080p
31.5in (80cm) 16:9 698.4*392.85 0.3637 1920x1080p
Storage
-4�F to 140�F (-20�C to 60�C)
Environment Temperature
Temperature End-Us e
32�F to 113�F (0�C to 45�C)
Temperature
Humidity Relative Humidity 10% to 85%

Resolution Compatibility—DVI/DP
Default Resolution (p) and Refresh Rate (Hz)
LED
SIZE Screen
Ratio (70Hz) (60/75/72.8Hz) (60/70/75/
120/144Hz)
(60/70/75/
120/144Hz)
(60/120/
144Hz)
(60/75/120/
144Hz)
(60/120/
144Hz)
(60/120/
144Hz)
(60/120/
144Hz)
(60/120/
144Hz)
(60/120/
144Hz)
(60/120/
144Hz)

27"
16:9
31.5"

Resolution Compatibility—HDMI
Default Resolution (p) and Refresh Rate (Hz)
LED
SIZE Screen
Ratio (70Hz) (60/75/72.8Hz) (60/70/75/ (60/70/75/ (60/120Hz) (60/75/120Hz) (60/120Hz) (60/120Hz) (60/120Hz) (60/120Hz) (60/120Hz) (60/120Hz)
120Hz) 120Hz)

27"
16:9
31.5"

Note:
“O” supports the corresponding resolution and refresh rate.
“X” does not support the corresponding resolution and refresh rate.

All specifications and informations are subject to change without notice.

-7-
1 Year Limited Hardware Warranty
Viotek Inc. (Viotek) offers a ONE YEAR limited warranty covering the hardware of Viotek LED Monitor
(“Product”), limited to those residing in the 50 US States and Canada. This warranty gives you specific legal
rights and you may also have other rights which vary from state to state.
Viotek warrants the Product to be free from defects in materials and workmanship under normal use for one
(1) year, as sold to the original purchaser, from the date of retail purchase by the original end-user purchaser.
If a hardware defect arises and a valid claim is received within the warranty period, at its option and to the
extent permitted by law, Viotek will: (1) repair the hardware defect by using new or refurbished parts that are
equivalent to new in performance and reliability; or (2) exchange the product with a product that is new or
refurbished, that is substantially equivalent to the original product. This warranty is for replacement for like-
items only and does not cover items out of production if the company no longer stocks them. This warranty is
not assignable or transferable. The original purchaser may call the Viotek toll-free number at 1-855-229-9472
for service request.
Upon Viotek's replacement or repair of a Product under warranty, the original end-user purchaser will have
the remaining warranty under the original warranty period (without any postponement during repair or
replacement). When a product or part is exchanged, any replacement item becomes your property and the
replaced item becomes Viotek's property. Important: Do not disassemble the Product. Disassembling the
Product will void this warranty. Only Viotek or a party expressly authorized by Viotek should perform service
on this Product.
This warranty only covers technical hardware defectiveness during the warranty period and under normal use
conditions. Viotek does not warrant uninterrupted or error-free operation of this Product. This Warranty does
not apply to damages or circumstances, such as, but not limited to:
(a) Damage that is caused by conditions, malfunctions, or damage not resulting in from defects in material or
workmanship. These conditions include, but are not limited to, accidents, and improper operation or
maintenance;
(b) Product has been tampered with, repaired and/or modified by non-authorized personnel;
(c) Obsolescence;
(d) Damage (accidental or other) to the Product that is cosmetic, meaning damage that does not impact the
operation and functioning of the Product, such as without limitation to rust, change in color, texture or finish,
wear and tear, scrapes, scratches, dents, cracks, or gradual deterioration;
(e) Damage to the Product caused by war, terrorism, fire, accident, natural disaster, intentional or accidental
misuse, abuse, neglect or improper maintenance, use under abnormal conditions, accidental drops, abuse or
fire;
(f) Damage to the Product caused by an external electrical fault, surge, or any electrical anomaly;
(g) Any contamination, condition or other circumstance, which Viotek, in its sole discretion, considers a
danger to health and safety, including, but not limited to any contact between the Product and a biohazard,
bodily fluids, infectious materials/substance, chemicals, hazardous substances, diseases, radiation, or other;
(h) Fraud, theft, misplacement, unexplained disappearance, or willful acts.

DISCLAIMER OF WARRANTY
TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE
AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL, WRITTEN, STATUTORY,
EXPRESS OR IMPLIED. AS PERMITTED BY APPLICABLE LAW, VIOTEK SPECIFICALLY DISCLAIMS ANY AND ALL
STATUTORY OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A
PARTICULAR PURPOSE, AND WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS. IF VIOTEK CANNOT LAWFULLY
DISCLAIM STATUTORY OR IMPLIED WARRANTIES THEN TO THE EXTENT PERMITTED BY LAW, ALL SUCH
WARRANTIES SHALL BE LIMITED IN DURATION TO THE DURATION OF THE EXPRESS WARRANTY AND TO THE
REPAIR OR REPLACEMENT SERVICE AS DETERMINED BY VIOTEK IN ITS SOLE DISCRETION. NO RESELLER, AGENT,
OR EMPLOYEE IS AUTHORIZED TO MAKE ANY MODIFICATION, EXTENSION, OR ADDITION TO THIS WARRANTY. IF
ANY TERM(S) IS HELD ILLEGAL OR UNENFORCEABLE, THE LEGALITY AND ENFORCEABILITY OF THE REMAINING
TERMS SHALL NOT BE AFFECTED OR IMPAIRED.

All specifications and informations are subject to change without notice.

-8-
EXCEPT AS PROVIDED IN THIS WARRANTY AND TO THE MAXIMUM EXTENT PERMITTED BY LAW, VIOTEK IS NOT
RESPONSIBLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
ANY BREACH OF WARRANTY OR CONDITION OR PERFORMANCE OF THE PRODUCT, OR UNDER ANY OTHER LEGAL
THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR ANTICIPATED
PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED
SAVINGS; LOSS OF BUSINESS; LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATION; LOSS OF,
DAMAGE TO, COMPROMISE, OR CORRUPTION OF DATA; OR ANY INDIRECT OR CONSEQUENTIAL LOSS OR DAMAGE
HOWSOEVER CAUSED INCLUDING THE REPLACEMENT OF EQUIPMENT AND PROPERTY, ANY COSTS OF
RECOVERING, PROGRAMMING OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH THE
PRODUCT AND ANY FAILURE TO MAINTAIN THE CONFIDENTIALITY OF DATA STORED ON THE PRODUCT. THE
FOREGOING LIMITATION SHALL NOT APPLY TO DEATH OR PERSONAL INJURY CLAIMS, OR ANY STATUTORY
LIABILITY FOR INTENTIONAL AND GROSS NEGLIGENT ACTS AND/OR OMISSIONS. VIOTEK DISCLAIMS ANY
REPRESENTATION THAT IT WILL BE ABLE TO REPAIR ANY PRODUCT UNDER THIS WARRANTY OR MAKE A
PRODUCT EXCHANGE, AND IS UNABLE TO RECOVER ANY USER SOFTWARE OR DATA ON THE DEVICE.

DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.

Federal Communications Commission Notice

“Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.”
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
+ Reorient or relocate the receiving antenna.
+ Increase the separation between the equipment and receiver.
+ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
+ Consult the dealer or an experienced radio/TV technician for help.

All specifications and informations are subject to change without notice.

-9-