FieldServer Protocol Driver Sheet
Edwards Systems
Technology- QuickStart
FS-8700-93 Version: 1.05 / Rev. 2
1 DESCRIPTION restarted to clear all point status, and then re-
annunciate any active devices after the FieldServer
The QuickStart Serial driver allows the FieldServer to has been started. This should only be undertaken by
record data from Edwards System Technology QS1- qualified technicians.
2/4-8 and QSC Fire Panels over the RS-232 printer
port. The FieldServer acts as a Passive Client Should the panel be soft restarted unexpectedly, the
receiving messages and updating its internal data FieldServer will recognize the "restart" command and
arrays which records the status of devices connected clear all internal data arrays. There will be no need
to the QuickStart fire alarm control panel. The for FieldServer restart; however, for a hard restart,
QuickStart panels currently do not support duplexed the FieldServer data arrays should be manually
communications; therefore, this driver has only been cleared by changing a bit in the CLEAR_FLAG data
designed to listen for messages passively and not to array through RUINET, then soft restarting the panel
respond or to generate polls. again to ensure that status of all points is re-
annunciated and recorded by the FieldServer.
The main purpose of this driver is to record the status
of Fire Alarm System points in bit oriented data 1.2 Device States
arrays. It is limited by the information that the
QuickStart control panels broadcasts in the form of Each addressable device (real or pseudo) can have
text messages through its RS-232 printer port. multiple states: alarm supervisory, monitor, other
(security), and troubles. These states are not
The types of EST messages supported by this driver exclusive; therefore, a single addressable point may
are listed later in this fact sheet and in the occupy multiple states at the same time.
FieldServer Driver Manual. Device status to the data
array mapping is also provided. Since there are a Although there may be several trouble states for each
variety of optional cards that can be selected for each device, there can only be a single alarm, supervisory,
QuickStart installation, each FieldServer application monitor and other (security) state per address.
must be specifically configured before use. Therefore any restoring messages for these four
FieldServer data storage arrays for panel status will states indicate that the device is clear of any active
be allocated according to the number and type of problems for these types of conditions.
cards implemented. Message information will also be However, there may be several trouble states for a
stored according to card and panel addressing. single addressable port. These trouble states will be
This driver is connection oriented; therefore, only one recorded in a separate trouble array of 2 byte
EST Panel may be connected to any single RS-232 elements. Each array element will correspond to a
FieldServer port. device address and each bit within the element will
correspond to a trouble type. The mapping of
The driver currently accommodates European and message trouble types to element bit configuration is
American English Conventional/Intelligent panels given below. For modeling simplicity and flexibility, it
using the American English protocol with provisions is assumed that all addressable points (real or
for using the British English protocol at a later date. pseudo) can exist in all states.
1.1 FieldServer Synchronization 2 FORMAL DRIVER TYPE
To synchronize the FieldServer's data arrays with the Serial
QuickStart control panel's status, the panel must
Passive Client
have no active or disabled points on FieldServer
startup. Alternatively, a panel can be hard/soft
Page 1 of 3
www.sierramonitor.com
FieldServer Protocol Driver Sheet
Edwards Systems
Technology- QuickStart
FS-8700-93 Version: 1.05 / Rev. 2
Event Description Text Strings State Comments
3 COMPATIBILITY MATRIX -OPERATOR
ACTIVATE
COMMAND- clears
RESTART
all the Data Arrays
Compatible with
FieldServer Model QUIESCENT QUIE RST Not Implemented
this driver ALARM ACTIVE ALARM RST A
FS-x30 Yes PULL STATION PULL STA RST A
HEAT ALARM HEAT ALM RS A
SlotServer Yes WATERFLOW WATERFLOW RS A
ProtoNode Yes STAGE ONE A
SUPERVISORY SUP RST S
QuickServer FS-QS-10xx No TAMPER TAMPER RST S
QuickServer FS-QS-12xx Yes SECURITY SECURITY RST O
ProtoCessor FPC-ED2 No FIREPHONE PHONE RST M
MONITOR MONITOR RST M
ProtoCessor FPC-ED4 Yes LATCH SUPV LAT SUPV RST S
LATCH TAMPER LAT TAMP RST S
UNKNOWN UNKNOWN RST O
4 CONNECTION INFORMATION ALARM VERIFY ALM VFY RST M
PREALARM PREALARM RST M
TROUBLE OPEN TBL OPEN RST T
Connection type: RS-232 (Simplex) TROUBLE SHRT TBL SHRT RST T
Baud Rates: 9600 (Vendor Limitation) LCL TROUBLE LCL TRBL RST T
Data Bits: 8 (Vendor Limitation) MAINT ALERT MAT ALERT RS M
DIRTY HEAD DTY HEAD RST T
Stop Bits: 1 (Vendor Limitation) COMMN FAULT COMM FLT RST T
Parity: None (Vendor Limitation) GROUND FAULT GND FLT RST T
Multidrop Capability: No INTERNAL TBL INTR TRBL RS T
BAD TYPE BAD TYPE RST T
BAD PRSONATY BAD PRSTY RS T
UNEPECT DEV UNEC DEV RST T
5 DEVICES TESTED TROUBLE TROUBLE RST T
RELAY CONFIR RLY CFRM RST M
Tested LCL MONITOR LCL MNTR RST M
Device SWITCH SWITCH RST M
(FACTORY, SITE) TEST TEST RST T
Edwards Systems DEV COMPATBL DEV COMP RST T
Technology- European and AND GROUP AND GRP RST A
MATRIX GROUP MATRIX G RST A
American QS1-2/QS4-8 SITE SERVICE GRP SERVICE G RS T
Addressable Panels, and the TIME CONTROL TIME CNTL RS M
QSC Conventional Panel ACK ACK RST M
DISABLED DISABLED RST T
DISAB SOUND DISSOUND RST T
OBJECT RUN OBJETRUN RST M
6 COMMUNICATIONS FUNCTIONS - ZONE ALARM ZONE ALM RST A
ZONE SUPER ZONE SUP RST S
SUPPORTED FUNCTIONS AT A ZONE MONITOR ZONE MON RST M
OUTPUT GROUP OUTPUT G RST M
GLANCE: AUDIBLE AUDIBLE RST M
VISUAL VISUAL RST M
SUPER OUTPUT SUPER OUT RT M
6.1 Message Types supported NONSUPER OUT NONSUP OUT R M
COMM ALM OUT COMMALOUTRST M
The primary purpose of this driver is to record the LED OUTPUT LEDOUTPU RST M
status of devices connected to the QuickStart Fire
Control Panel by interpreting the text messages sent
to its printer port. Not all messages are interpreted,
as many messages and reports do not directly affect
device status. The following set of events and
messages are recognized and recorded I the data
arrays.
Page 2 of 3
www.sierramonitor.com
FieldServer Protocol Driver Sheet
Edwards Systems
Technology- QuickStart
FS-8700-93 Version: 1.05 / Rev. 2
6.2 FieldServer Limitations and
Exclusions
Only one QuickStart panel may be connected to
any given RS-232 port at once.
QuickStart and FieldServer synchronization
requires some manual steps. This is described
in the section of this fact sheet called
“FieldServer Synchronization”.
This driver cannot poll for data, thus if a
message sent by the panel is lost or corrupted
the status reported by the FieldServer will not
correctly reflect the status of the panel until the
panel is synchronized again or until the
FieldServer receives a new message reporting
the status of the lost message’s point.
Because of the message structure for the
QuickStart protocol, it was intended to be the
only protocol assigned to any single port.
Page 3 of 3
Sierra Monitor Corporation
1991 Tarob Court, Milpitas, California 95305 USA
O. +1 408 262-6611 TF: +1 800 72 SIERRA (74377) F. +1 408 262-9042 www.sierramonitor.com
