2

:: Introduction
Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10TC6.2.
Please take a moment to read through this manual to help familiarize yourself with these steps.

We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on
supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before you start to build.

:: KIT Features
Team Associated is proud to release the next step in its developmental line of 1:10th scale 4WD electric touring car kits, the RC10TC6.2-FT, further refining the
already successful TC6 platform.

The touring car racing class has been moving forward at an aggressive rate, and the Engineers behind the doors of Area-51 have been hard at work evolving
the TC6 platform to keep the pace. The RC10TC6.2-FT car kit comes equipped with a host of new features to allow for more precise suspension adjustment and
consistent handling for any track condition.

With over two year’s development on the TC6 chassis, the TC6.2-FT car kit ties together all the experience and Factory Team race tested parts. Focusing on precise
suspension adjustments with features such as the new independent arm mount system with interchangeable toe inserts and pivot ball joints. A new dual
bellcrank steering system has optimal Ackermann and steering rates, and is controlled by a servo on a floating mount for steering to match today’s aggressive
racing conditions. Updated bulkhead and top plate configurations allow for optimized flex through the entire length of chassis to give the best grip on any surface.
The RC10TC6.2-FT packs together the key features necessary to keep you at the top of the racing circuit. All without sacrificing low part count or affordability.
It’s plain to see that the RC10TC6.2-FT kit is… another “Champion by Design” from Team Associated!

:: Key Features
• Updated arm mount system • Updated vertical ball stud bearing caps
o Pivot ball on inner hinge pin allows free pin movement at any toe o Optimized position for inner ball stud
or kickup angle o Vertical ballstud orientation allows for fine adjustments of roll
o Insert system for precise adjustment of inner pin width and toe center height
o Independent arm mount design to allow maximum flex through o 3 link position options give precise control of camber gain
entire chassis length, resulting in better grip on all track conditions • Spur gear lowered by 1.50mm to give more aggressive handling
• Dual bellcrank steering system characteristics
o Optimized Ackermann and steering rates • Top plate lowered by 1.50mm to allow for more chassis flex and increased
o Horizontal ballstuds for fine Ackermann adjustments traction in any condition
o 8 precision bearings for accurate swing motion • Rear gear diff for maximum performance and minimal maintenance
• Floating servo mount o Lightweight design
o Servo mounts to chassis center to allow equal chassis flex in both o Durable composite construction
directions and a tweak free assembly o Optimized for a wide “tuning window” to maximize useable
o Mount ties to steering bellcrank posts for stable servo positioning adjustability
o Slotted servo mount design allows fit for almost any standard servo o Hard anodized aluminum outdrives for low wear and long life
• Narrow chassis with optimized flex characteristics • Front spool with replaceable composite outdrives
o 2.25mm graphite laminate for optimized flex characteristics o Outdrives allow the use of existing CVA bone blades to minimize
o A narrow 88mm wide to minimize chassis dragging at maximum binding at the bearing surface
chassis roll angles o Composite outdrives are replaceable at low cost in the event of a
o Chassis ballast mass mounting locations to fine tune mass balance CVA bone blade failure
• Updated spur gear bulkheads • Cross-compatibility with all TC6.1 suspension components
o Mounting pattern has been made independent of arm mount to • VCS3 Shock with hard anodized threaded shock bodies
allow flex through entire length of chassis improving overall grip o Bottom loading seal system for ease of build
o Narrowed mounting pattern to allow for more chassis flex and o TiN coated shock shaft
consistent traction o Piston attaches to shock shaft with screw for tight clamping and no
o Symmetric design helps to minimize part count slop
• Updated motor mount & spur gear mount o Threaded collar with fine pitch thread for ease of accurate ride
o Floating spur gear design allows for more flex from rear of chassis height adjustment
helping to gain traction in all conditions • Titanium turnbuckles with turnbuckle eyelets for easy access to ball stud for
o Motor mount attaches to center line of chassis with a floating post adjustment
connection to allow free chassis flex in both directions • 22 precision ball bearings

:: Items Needed
Your new FT TC6.2 comes unassembled and requires the following items for completion. (refer to catalog section for suggestions):

• 1:10th scale electric motor and electronic speed control • 1:10th scale 190mm lexan touring car body and Lexan specific paint for body
• 3.7V-7.4V LiPo, 6.6V LiFe, or 4.8V-7.2V NiMh/NiCd battery
• Battery charger (suited for, and particular to, one of the batteries mentioned) • Strapping tape for battery
• 2 channel surface transmitter, 2 channel receiver, and steering servo • 1:10th scale rubber (or foam) touring car tires, rims and inserts

:: Other Helpful Items

• Silicone Shock Fluid (Refer to catalog for complete listings) • Silicone Diff Fluid (Refer to catalog for complete listings) • Thread Lock (AE Part #1596)
• Body Scissors (AE Part # 1737) • Reamer / Hole Punch • FT Hex Wrenches (AE Part # 1541) • Hobby Knife
• Needle Nose Pliers • Wire Cutters • Soldering Iron • Calipers or a Precision Ruler

Associated Electrics, Inc. Customer Service

26021 Commercentre Dr. Tel: 949.544.7500
Lake Forest, CA 92630 Fax: 949.544.7501
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
1/14
3
:: Table of Contents

1...................Cover 26-28.........Tuning Tips

2...................Introduction 29................Gear Chart

3...................Table of Contents 30-37.........Catalog

4-5...............Shock Build (Bag A-AA) 38................Notes

5-8..............Spool and Differential Build 39................Setup Sheet “Kit Setup”

(Bag B-BB)
40................1:1 Hardware “Fold Out”
8-9.............. CVA’s and Turnbuckles Build
(Bag C-CC) 41.................Setup Sheet “Blank”

10-11.........Suspension Arms Build 42................Back Cover

(Bag D-DD)

12-16........Bulkheads, Spur Gear, and

Steering Rack Build (Bag E-EE)

16-20........Steering/Caster Blocks and

Rear HubsBuild (Bag F)

21-25.......Bumper, Anti Roll Bar, and

Electronics Build (Bag G-GG)

:: Notes

This symbol indicates a special

! note or instruction in the manual.

There is a 1:1 hardware fold out page in the

back of the manual. To check the size of a part,
This symbol indicates a Racers Tip. line up your hardare with the correct drawing
until you find the exact size. Each part in the
foldout has a number assigned to it for ordering
replacement parts.
Associated Electrics, Inc. Customer Service
26021 Commercentre Dr. Tel: 949.544.7500
Lake Forest, CA 92630 Fax: 949.544.7501
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
4
:: Shock Build - Bag A-AA - Step 1
#1596
31510 thread lock
M2x4mm
bhcs 6465
Shock
!
Thread lock
31325 piston not included!
VCS3 shock 31324 (#2)
body VCS3
piston
bushing 31330
VCS3 shock
shaft
31327
VCS3 shock
bottom cap
o-ring

:: Shock Build - Bag A-AA - Step 2

Shock oil 31324

#5423 Shock
(40wt)
bladder

31324
VCS3
o-ring
Sh
oc spacer
#5 k oil
(40 423
wt
) 5407
Red
o-rings 31305
31324 Turnbuckle
Hat 31327 eyelet
bushing VCS3 shock
bottom cap

:: Shock Build - Bag A-AA - Step - 3

31328
Sh #5 0w
oc 42 t)

VCS3
k 3

31326
(4

oi
l

Aluminum VCS3 shock

cap retainer collar o-ring
Bladder Installation
With the shaft extended 25%, place bladder on
31329 31326
the top of the shock body, displacing the extra oil.
While maintaining pressure on the bladder against VCS3 shock VCS3
the shock body, carefully lift one side of the bladder cap shock collar
to allow any extra oil to escape. Place stock cap on
top of bladder, and secure it by threading the
aluminum cap retainer onto the shock body.
 5
:: Shock Build - Bag A-AA - Step 4

3942
Silver 6475
spring Shock
14.5lb spring cup
(front)
3942
Silver
spring
!
14.5lb Build four
(rear) shocks

:: Spool and Differential Build - Bag B-BB - Step 1

31342 31510 x4
Spool hub M2x4mm
bhcs

31175
Diff pulley
flange !
Thread lock

c a
97
#15 ue
gl !
CA glue
not included!

not included!
31175 #1596
Diff pulley thread lock

(40T)

:: Spool and Differential Build - Bag B-BB - Step 2

Cam Position
Belt Tension
Number

Left Side
1 16

!
Mid-Low Mid-High 31615 x2
31615 x2
Cam Diff
Use belt tension holder bearing
17 32
position 8 for (mid-low) cam
standard setup.
View from left
Low High side of car

Note!
Always use the same
cam position on both
Right Side
sides of the car.
6
:: Spool and Differential Build - Bag B-BB - Step 3
31341 x2
TC6 spool
outdrive

31350 x2
31401 x2 M2.5x10mm
10x15mm fhcs
bearing

ad 96
ck
lo
re 15
31162 x2

#
Shim
!

th
Thread lock
not included!

:: Spool and Differential Build - Bag B-BB - Step 4

31348
31348 x2 TC6 gear
31349 TC6 gear diff pin
TC6 gear diff shim
diff seals (1 small, 1 big)
se

31346
gr 8

31347
ea
ac 658

TC6 gear TC6 gear

#
k

diff outdrive
bl

diff case

31349
TC6 gear
8
58 as
e diff seals

!
#6 gre
ck
bla

Build two
outdrives

:: Spool and Differential Build - Bag B-BB - Step 5

31345
TC6 gear
diff sun
gear
31348 x2
TC6 gear
diff pin

31345 x4
TC6 gear
diff planet
31348 x4
gear
TC6 gear
diff shim
 7
:: Spool and Differential Build - Bag B-BB - Step 6
31348 x2 31345
TC6 gear TC6 gear
diff shim diff sun
31348
(1 small, 1 big) gear
TC6 gear
31347 diff pin
TC6 gear
diff pulley

31349
TC6 gear
8
58 as
e diff seals
#6 gre
c k
bla

:: Spool and Differential Build - Bag B-BB - Step 7

Sh
oc
!
Fill to top of
#5 k oil cross pins
(40 423 31347
wt
)
TC6 gear
diff gasket

:: Spool and Differential Build - Bag B-BB - Step 8

4675 x2 31162 x2
M2.5x6mm Shim
fhcs

31401 x2
10x15mm
bearing
8
:: Spool and Differential Build - Bag B-BB - Step 9

Cam Position
Belt Tension
Number

1 16
Left Side

Mid-Low Mid-High

17 32
!
Use belt tension
31615 x2
Diff
bearing
31615 x2
Cam
holder
position 7 for cam (mid-low)
Low High View from left standard setup.
side of car

Note!
Always use the same
cam position on both
Right Side
sides of the car.

:: Spool and Differential Build - Bag B-BB - Step 10

:: CVA’s and Turnbuckles Build - Bag C-CC - Step 1

8
58 ase
#6 gre
ck
bla

31367
TC6.1 CVA 31367
31368
coupler CVA
TC6.1 CVA
cross pin
bones
31369
TC6.1 CVA
axle
 9
:: CVA’s and Turnbuckles Build - Bag C-CC - Step 2

31500

ad 96
ck
lo
re 15
M3x2.5mm

#
setscrew

th
Note!
Align the gap in the
pin retainer to be
opposite of the CVA
pin.

!
Thread lock
not included!
31237
retaining
clip

:: CVA’s and Turnbuckles Build - Bag C-CC - Step 3

!
31238
CVA blade

Build four
CVA’s

:: CVA’s and Turnbuckles Build - Bag C-CC - Step 4

Servo Turnbuckle
1418
0.825” 31305
turnbuckle Turnbuckle
eyelet 34.65mm

Camber Turnbuckle
1402 Front x2 Rear x2
1.375”
turnbuckle

46mm 49.50mm

Steering Turnbuckle 1405 x2

1.875”
turnbuckle

57mm
10
:: Suspension Arms Build - Bag D-DD - Step 1
31620
TC6.2 arm

! mount insert
(1 dot) 4617 x4
Front
Build four
bulkhead
inner arm shim
mounts (0.5mm)
31619
TC6.2 Inner
arm mount
31600

!
Arm Mount Inserts
-3 DOT -2 DOT 1 DOT +2 DOT +3 DOT TC6.2
chassis
Install
-1 ° -1/2 ° 0 ° +1/2 ° +1 ° 31541 x4
Negative to the inside of vehicle. M3x6mm front and
Positive to the outside of vehicle. fhcs rear

:: Suspension Arms Build - Bag D-DD - Step 2

25227 31621 x2
M4x8mm Inner hinge
setscrew pin ball

31221
Inner
31200
Wheelbase
shim (2mm)
!
hinge pin Build left
31356 and right
Front sides
suspension
arm
Suspension Arm Insert
(front)
Wheel Base Shims
31356 A C
31280 Front B

31200 5mm suspension 1mm 2mm

Wheelbase ballstud arm insert
shim (1mm) (short) (B) A B C

:: Suspension Arms Build - Bag D-DD - Step 3

31621 x2
31221 Inner hinge
Inner pin ball
hinge pin 31200

!
25227
M4x8mm Wheelbase
setscrew shim (1mm)
Build left
31283
5mm and right
ballstud sides
(long)
Suspension Arm Insert
31357 (rear)
Wheel Base Shims
Rear C A
B
31357 suspension
31200 Rear arm insert 1mm 2mm
Wheelbase suspension (B)
shim (2mm) arm C B A
 11
:: Suspension Arms Build - Bag D-DD - Step 4
31620 x2
TC6.2 arm
mount insert
(1 dot) !
Build two, one for
front, one for rear.
Both with 1 dot inserts

Arm Mount Inserts

-3 DOT -2 DOT 1 DOT +2 DOT +3 DOT

31618
TC6.2
-1 ° -1/2 ° 0 ° +1/2 ° +1 °
Outer Arm Negative to the inside of vehicle.
Mount Positive to the outside of vehicle.

:: Suspension Arms Build - Bag D-DD - Step 5

4617 x2
Front
bulkhead
shim
(0.5mm)

31541 x2
M3x6mm
fhcs

:: Suspension Arms Build - Bag D-DD - Step 6

Droop:
The standard settings of Front Droop
6mm front and 5mm rear
will work best in most cases.
Setting: 6mm
Droop is measured just
4617 x2 underneath the outer hinge
Front pin as shown in the photos
6 78
to the right. 345
bulkhead 01 2

shim On bumpy or low grip

(0.5mm) surfaces, increase the droop
(going to a lower number on Rear Droop
the droop gauge), this will
help increase traction and Setting: 5mm
consistency.

Droop adjustments of
0.5mm to 1mm can be
31541 x2 very effective on the track!
78
M3x6mm 01 2
345
6

fhcs
12
:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 1
31612 x2
31612 x2 TC6.2
TC6.2 Bulkhead
Bulkhead

31540 x4 31540 x4
M3x5mm M3x5mm
fhcs fhcs

:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 2

31616
TC6.2
spur gear
31616 31617 bulkhead
TC6.2 TC6.2 motor
spur gear mount
bulkhead standoff

31532 x2
31617 M3x8mm
TC6.2 bhcs
motor 31540 x5
mount M3x5mm
fhcs

:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 3

31314
TC6 spur
gear hub
!
Thread lock
not included!

31319
TC6 spur gear
clamping ring
6
59 ck
#1 lo
e a d
thr

31333
TC6 31320 x2
spur gear 31530 x3 TC6 spur
(87T / 48P) M3x5mm pulley
bhcs (20T)
 13
:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 4

31160 31160
3mm 3mm
31315
E-clip E-clip
TC6 spur
gear shaft

31162 x2
Shim
31331 x2
4x8x3
flanged
bearing

:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 5

Rear Belt

Front Belt
31188
Rear belt
31187
Front belt

:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 6

31521 x2
M2.5x8mm
bhcs
14
:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 7

!
Slide belt over
!
Slide belt over
spool pulley! gear diff pulley!

:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 8

31280 x2
Ballstud, 31531 x4
short, M3x6mm
31286 x2 bhcs
FT ballstud 5mm
washer,
aluminum
(2mm)

31613
TC6.2
bearing
cap (A) 31614
TC6.2
bearing
cap (B)

:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 9

31531 x4
31286 x2 31280 x2 M3x6mm
FT ballstud Ballstud, bhcs
washer, short,
aluminum 5mm
(1mm)

31614
TC6.2
bearing
cap (B)
31613
TC6.2
bearing
cap (A)
 15
:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 10

! !
Belt hidden for
31530 x9
M3x5mm
Note! view clarity! bhcs
Place top
plate between
the front belt.

31601
TC6.2
top plate

:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 11

31531 x2
M3x6mm
bhcs
31604
TC6.2 front
shock tower

31250 x2
31541 x4
Shock
M3x6mm
bushing
fhcs

:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 12

31541 x4
31250 x2 M3x6mm
Shock fhcs
bushing

31531 x2 31605
M3x6mm TC6.2 rear
bhcs shock tower
16
:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 13
31374
TiN 3.25mm
ballstud,
31286 x2
short neck 31610 x2
FT ballstud
washer, TC6.2
aluminum steering
(1mm) bellcrank

31611 31403 x8
TC6.2 Bearing,
31609 x2
31283 x2 steering 4 x 7mm
TC6.2
Ballstud, rack
steering
long, bellcrank
5mm post

:: Bulkheads, Spur Gear, and Steering Build - Bag E-EE - Step 14

31609 x2
TC6.2 steering
bellcrank post
spacer
31611 x2
TC6.2 steering
rack hat
bushing
!
Top Plate and
Belts hidden for
view clarity!

31540 x2
25211 x2 M3x5mm
M3x10mm fhcs
bhcs

:: Steering / Caster Blocks Build - Bag F - Step 1

31280
31360

!
5mm
TC6.1 ballstud
steering

!
(short)
blocks Build left
Note offset
and right
(Left side shown) sides
31370
TC6.1
axle crush
tube
25237 x2
5x10mm
bearing
 17
:: Steering / Caster Blocks Build - Bag F - Step 2

31112
1/16” x 5/16”
dowel pins

!
Build left
and right
sides
31511 31234
31162 M2x5mm Clamping
Axle shim shcs wheel hex

:: Steering / Caster Blocks Build - Bag F - Step 3

31358

!
TC6.1 caster
blocks
(left and right)
Use the supplied
symmetric inserts to
select caster angle. When
viewed from the front, the
number should be located RACERS TIP:
on the top side of the pin, Use small amount ca glue to
as shown in the view to the
! right. When viewed from
permanently secure the caster
block inserts in the caster
the rear, the number should blocks.
be located on the bottom.
Left Right
31358 x2
! TC6.1 caster 4 4
block
inserts
(4 deg)

:: Steering / Caster Blocks Build - Bag F - Step 4

31214 x2
Caster

!
block
bushing

Build left
and right
sides
18
:: Steering / Caster Blocks Build - Bag F - Step 5
31284
8mm
ballstud
(long)

!
Build left
and right
sides

31532
M3x8mm
bhcs

:: Steering / Caster Blocks Build - Bag F - Step 6

!
Build left
and right
sides

31510 31222
M2x4mm Outer
bhcs hinge pin

:: Steering / Caster Blocks Build - Bag F - Step 7

!
Orient the notch
to the left throughout
the car. The notch
indicates which end has
the left hand threads!
 19
:: Steering / Caster Blocks Build - Bag F - Step 8

It is important that the turnbuckle eyelets move freely

once snapped on to the ballstud. If the fit is too tight,
the car handling will be inconsistent. To check, grab
turnbuckle eyelet with fingers and rotate the cup. If

!
there is resistance, lightly squeeze ball cup with needle
nose pliers as shown and test again. It is important
that the ball cup be snapped onto the ballstud before
squeezing with needle nose pliers. Be sure to check
and adjust the fit for each ball cup that is installed.

:: Steering / Caster Blocks Build - Bag F - Step 9

31359 x2
TC6.1
rear hub
!
carrier
! Use the supplied
symmetric inserts to select
rear hub toe angle.
When viewed from the
back, the number should
be located on the outside
31359 of the hinge pin, as shown
in the view to the right. RACERS TIP:
TC6.1 Use small amount of ca
When viewed from the
rear hub front, the number should glue to permanently secure
carrier be located on the inside
0 the rear hub inserts in the 0
inserts of the hinge pin. hubs.
(0 deg)
! Left Right

:: Steering / Caster Blocks Build - Bag F - Step 10

31284
8mm
ballstud 31162
(long) Axle shim
31286
Aluminum
ballstud
washer
(2mm)
31370
TC6.1
axle crush
tube
25237 x2
5x10mm
bearing
20
:: Steering / Caster Blocks Build - Bag F - Step 11

31112
! 31510
1/16” x 5/16” Build left M2x4mm
dowel pins and right bhcs
sides
31234 31222
Clamping Outer
wheel hex hinge pin

!
Build left 31511
and right M2x5mm
sides shcs

:: Steering / Caster Blocks Build - Bag F - Step 12

!
Orient the notch
to the left throughout
the car. The notch
indicates which end has
the left hand threads!

:: Steering / Caster Blocks Build - Bag F - Step 13

31530 x2
M3x5mm
31530 x2
bhcs
M3x5mm
bhcs
 21
:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 1

4673 x3
M2.5x4mm
bhcs

!
Transponder 31624
not included! 31625 x2 TC6.2
TC6.2 front foam
body posts bumper

31623
25203 x2
TC6.2
M3x12mm
bumper
fhcs

:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 2

1736 x2
3897 x2 FT body
Pivoting clips, blue
body mounts (short)

31623 25201 x3
TC6.2 M3x8mm
bumper fhcs
brace

:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 3

3897 x2
Pivoting
body mounts
1736 x2
FT body
31532 x2
clips, blue
M3x8mm
(short)
bhcs

31625 x2
TC6.2 rear
body posts
25201 x2
M3x8mm
fhcs
22
:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 4
6338 31500
Antenna M3x2.5mm
tube & cap set screw

31626
Antenna
31626 mount
TC6.2 lipo
brace 31626
Inner lipo
brace
!
Top Plate and
Belts hidden for
31626 31541 x4 view clarity!
TC6.2 lipo M3x6mm
brace fhcs 31540 x3
(offset) M3x5mm
fhcs

:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 5

8828
Anti roll
bar cups

!
31269 Build four anti-

!
Anti roll roll bar mounts
bar pivot Anti Roll Bar
mount Link Adjustment Install four
anti-roll bar mounts,
two for the front
arms and two for
the rear arms.
31058 14mm
Anti roll 31511 x2
bar M2x5mm
ballstud shcs

:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 6

Front 31628 x2
Anti Roll Bar
Anti roll
Color/Size Chart
bar pivot
Green 0.8mm
31364 31500 x4 White 0.9mm
1.1mm M3x2.5mm Blue 1.0mm
roll bar set screw Yellow 1.1mm
(yellow) Red 1.2mm

31627
TC6.2
anti roll
bar tube
!
Shrink the colored
heat shrink tubing to
the anti roll bar!
 23
:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 7
31511 x2 31628 x2
Rear Anti roll
M2x5mm
shcs bar pivot
Anti Roll Bar 31500 x4
31364
Color/Size Chart
0.9mm M3x2.5mm
Green 0.8mm roll bar set screw
White 0.9mm (white)
Blue 1.0mm
Yellow 1.1mm
Red 1.2mm

31627
TC6.2
31365 x2 anti roll
bar tube
!
Anti roll Shrink the colored
bar mounts heat shrink tubing to
the anti roll bar!

:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 8

31365 x2
31511 x2
Anti roll
M2x5mm
bar mounts
shcs

:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 9

Steering Servo Chart # 89007
servo arm Drill top hole to
Associated XP-1015, XP-1313
Airtronics 94102
F

A
! 2.5mm, then install
ballstud and locknut
31550
31286
Airtronics
94738, 94157, 94158, 94257, 94258, 94357, A FT M3 Locknut,
94358, 94452, 94453, 94751, 94755 Aluminum
blue aluminum
Hitec HS-5625MG, HS-5645MG, HS625MG, HS645MG H ballstud washer
Hitec
HS-322HD, HS-325HB, HS-965, HS-985MG, H
(1mm, 2mm)
HS-5965, HS-5985MG, HS-425BB, HS-422
JR Z4725, Z4750, Z2750, Z8450, Z8550, NES-4750 J

JR Z250, Z550 J

Futaba S9204, S9250, S9450, S148 F

Futaba S3003, S9202, S9101 F 89007

Futaba S9404 F Servo
KO
PS-401, PS-2001, PS-2004, PS-2015, PS-2173, J
horn ring
PS-2174, PS-2123, PS-2143, PS-2144 31285
10mm 89007
* Not all servo’s are listed
* Make sure servo linkage clears the servo through full travel in both ballstud Servo
directions. Use #7336 servo spacers to adjust servos position as necessary. (long) horn
24
:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 10
7336 x2 31622 x2
Servo TC6.2
spacer servo
mounts

!
Use screw that was included
7337 x4
.250x.125x.015
with your servo.
31532 x4
Servo not included! M3x8mm washer
bhcs

:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 11

31530 x5
M3x5mm
bhcs

31608

!
Top Plate
TC6.2 servo
mount brace

hidden for
view clarity!

31540 x2
M3x5mm
fhcs

:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 12

!
Receiver not
!
ESC not included!
included!

6727
Servo tape 6727
Servo tape
 25
:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 13
Gearing will depend on the
motor and track size.
Gear chart on page 29.
Motor, pinion gear, and set
screw are not included!

!
31286 x2
Aluminum
ballstud
washer
(1mm) 31532 x2
M3x8mm
bhcs

:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 14

! !
Battery and strapping
Use strapping tape to
secure battery into chassis. tape not included!
Wrap the tape around the
#31626 LiPo brace an back
onto itself.
Battery tape not included!

:: Bumper, Anti-Roll Bar and Electronics Build - Bag G-GG - Step 15

!
Wheels, tires, and inserts
91148 x4
M4
locknut
not included!
26
:: Tuning Tips
Tips for Beginners:
Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your car
will not be beneficial if you can’t stay on the track. Your goal is consistent laps.

Once you can get around the track consistently, start tuning your car. Make only ONE adjustment at a time, testing it before making
another change. If the result of your adjustment is a faster lap, mark the change on the included setup sheet (make additional
copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back to the previous setup and try another
change.

When you are satisfied with your car, fill in the setup sheet thoroughly and file it away. Use this as a guide for future track days or
conditions.

Ride Height:
The standard starting point for ride height is 5.0mm (keep in mind that your local track may have minimum ride height
requirements). You can slightly raise the rear relative to the front to give the car more steering. Raise the car slightly for tracks
with large bumps.

Battery Placement:
For most cases, run the battery in the standard forward position. Typically this will be the most stable and easiest to drive. Try
moving the battery back if you encounter a low traction surface by switching LiPo braces front to back.

Wheelbase: Wheel Base Shims

Lengthening the front will reduce steering, shortening the front will increase steering. Shortening the rear will
increase rear grip, lengthening the rear will decrease rear traction. 1mm 2mm

Rear Toe-In:
The TC6.2 allows rear toe adjustments in two positions: inner hinge pin, and outer hinge pin at the rear hub. In general, decreasing
rear toe-in will decrease rear traction and increase corner speed.
Arm Mount Inserts
-3 DOT -2 DOT 1 DOT +2 DOT +3 DOT

Rear toe-in can be adjusted by 0.5° increments at the inner hinge pin with
supplied arm mount inserts (see chart to right). Standard toe-in angle for
inner hinge pin when using same insert front and rear is 3°. -1 ° -1/2 ° 0 ° +1/2 ° +1 °
Standard insert used is 1 dot. Negative to the inside of vehicle.
Positive to the outside of vehicle.
Use rear hub inserts to change toe at the outer hinge pin by 0.5° increments.
Note the number on hub insert should be on outside of hinge pin for proper installation.

Ackermann & Steering Rate:

Less Ackermann
Steering Steering
Block Rack
Ackermann refers to the relative angle difference between the front wheels as they are Position Shims
turned to steer the car. The outside wheel will turn less than the inside wheel in most
conditions. Settings with more Ackermann will have a bigger difference in wheel angle, B 2mm
causing the outside wheel to turn less. Likewise, settings with less Ackermann will cause
the outside wheel to turn more.
B 1mm STD
Increasing the Ackermann will smooth out the steering and is used most often on high
traction surfaces such as carpet. This is a result of the reduced outside wheel angle. B 0mm
More Ackermann

Settings with reduced Ackermann will help to increase corner entry steering, and are
typically used when running a spool in the front. A 2mm

The chart to the right lists the different Ackermann options. A 1mm

A 0mm

B A

Steering Block
 27
:: Tuning Tips
Caster:
Caster describes the angle of the kingpin from vertical while looking from the side of the car. Positive caster means the top of the
kingpin leans rearward. Negative caster means the kingpin is leaning towards the front of the car. Since caster is measured at the
wheel, it is affected by running any inclination in your inner arm mount. Kick-up adds (+) caster, and anti-dive adds (-) caster.

When figuring out your caster at the wheel, add the number of degrees of kick-up or anti-dive and add it to the degree caster blocks
you have on the car.

Typically for most racing surfaces, 4 degrees caster is the normal starting point for the Team. From there, increase caster to reduce
mid to exit steering and make the front end less responsive. Conversely, decreased caster gives a more responsive feel and more exit
steering.

Droop:
The standard settings of 6mm front and 5mm Front Droop Rear Droop
rear will work best in most cases. Droop is
measured just underneath the outer hinge pin Setting: 6mm Setting: 5mm
as shown in the photos to the right.

On bumpy or low grip surfaces, increase the

droop (going to a lower number on the droop
gauge), this will help increase traction and
6 78 6 78
345 345
01 2
consistency.
01 2
Droop adjustments of 0.5mm to 1mm can be Increase Decrease Increase Decrease
very effective on the track!

Camber Link Position:

The camber link is used to set static camber at ride height, but it is also an effective setting to adjust roll center height and camber
gain. The TC6.2 has three optimized length positions at the front, and six at the rear, for a wide range of camber gain adjustments.
All camber link mounting positions use vertical ballstuds that can be shimmed for precise roll center height adjustments.

Longer links will produce less camber gain, stiffening that particular end of the car in roll. These are particularly effective on large
tracks with big sweeping corners. Shorter links will give more camber gain, softening that end of the car in roll. This will make the
car more aggressive, and is a good setting for smaller indoor tracks with high grip levels.

The angle of the camber link will make fine adjustments to the roll center height. Typically the camber link will be no more than
parallel to the suspension arm with the inboard side of the link lower than the outboard side. As the inboard side of the camber link
is moved down, the roll center goes up, stiffening that end of the car. Camber link angle is a good adjustment to help fine tune the
balance of the car to the track by setting the front and rear at slightly different angles.

Arm Mount Position:

The TC6.2’s arm mount system allows for maximum adjustability for all track and racing conditions. Independent inner and outer arm mounts
with interchangeable inserts provide multiple pin configurations... flat, or with angle, to give a host of kickup/tow and pin width options.

Use the TC6.2’s included arm mount inserts to adjust pin width and angle. The arm
mount inserts are indicated one, two, and three with the corresponding amount of dots
on their exposed face. Each insert will index the hinge pin by 1/2 degree (or 0.43mm).
Standard pin angle is achieved when using the same insert in both the inner and outer 4
3
mounts. Rear hinge pin angle is 3° when using the same insert in both inner and outer 2
1
mounts.

The chart to the right shows the pin angle change for the right rear pin when using
a 1 dot insert in the inner arm mount.

Pin width can also be adjusted by changing the inserts in the inner and outer mounts
by an equal amount. The standard pin width for the TC6.2 uses 1 dot inserts at all
corners, and is best suited for rubber tire racing.

The TC6.2’s independent inner and outer arm mount system also allows for roll center
height adjustements as well as options for anti-dive/kick-up and anti-squat/pro-squat
hinge pin angles. Precise adjustments can be made by changing the shim thickness ABC
between the arm mounts and chassis.

The standard roll center height uses o.5mm shims on all mounts. This produces a
relatively low roll center with more chassis roll on the corners... typically good for lower
grip conditions such as rubber tires on asphalt. If the grip level is high, try raising the Arm Mount Inserts
roll center by using thicker shims between the mounts and chassis. -3 DOT -2 DOT 1 DOT +2 DOT +3 DOT

Anti-dive/kick-up and anti-squat/pro-squat angles can be adjusted by varying the

amount of shims under the inner and outer mounts. A 0.5mm difference will produce
an angle of about 1/2 degree. The following sections briefly describe front and rear -1 ° -1/2 ° 0 ° +1/2 ° +1 °
pin angles and their effect on the track. Negative to the inside of vehicle.
Positive to the outside of vehicle.
28
:: Tuning Tips
Anti-Dive (front):
Anti-dive is a front arm angle where the rear mount is higher than the front mount. Adding anti-dive reduces weight transfer to the
front on deceleration entering corners. It also reduces caster at the wheel.

Kick-Up (front):
Kick-up describes the angle of the front suspension arm, where the front mount is higher than the rear mount. Increasing kick-up will
give more entry steering, as well as increasing caster at the wheel.

Anti-Squat (rear):
Anti-Squat describes a rear arm angle where the front mount is higher than the rear mount. Increasing anti-squat will make the rear
suspension stiffer. It tends to give the car more entry steering and reduce rearward weight transfer on power.

Pro-Squat (rear):
Pro-squat is a rear arm angle where the rear mount is higher than the front mount. Running Pro-Squat will increase rearward
weight transfer on power.

Anti-Roll Bar: Anti Roll Bar

Color/Size Chart
Anti-roll bars are only effective during roll (when the chassis leans from side to side when cornering).
Because of this they isolate a change in the suspensions spring rate in the corners only, and can be a very useful Green 0.8mm
tuning option. White 0.9mm
Anti-roll bars stiffen the spring rate of the suspension during roll movements when cornering. The larger the
Blue 1.0mm
roll bar wire, the stiffer the spring rate will be in roll. The chart on the right shows the available anti-roll bar Yellow 1.1mm
sizes (as well as their corresponding colors) from the softest on the top, to the stiffest on the bottom. Red 1.2mm
The standard setup, using yellow front anti-roll bars (1.1mm) and white rear anti-roll bars (0.9mm), is a balanced starting point.
Changing the size of the front or rear anti-roll bars can help to make the chassis more consistent through the corner. Decreasing the
size of the front anti-roll bars will help to increase mid-corner steering, but will tend to be less stable in sweepers. This is a
typical setup for smaller tracks with tighter turns. Increasing the size of the front anti-roll bars will give more stability in the
sweepers, and is better for larger tracks with high speed corners. Increasing the size of the rear ant-roll bars will help add stability
into and through the corner in high traction conditions, but can make the car inconsistent in low traction, or bumpy, surfaces.

Belt Tension: Cam Position

Belt Tension
Number Height Pos.

When altering the differential height, you will need High 31

to adjust the tension of the belt. The following chart

Front
1 16
Mid-High 28
shows suggested starting positions.
Mid 8
Mid-Low Mid-High Low 5

Height Pos.
17 32
Looser Tighter Tighter Looser High 18
Rear

Low High View from left Mid-High 20

side of car
Mid 7
Low 9
Left Side Left Side
Front Front
Note! Charts show left side cam positions from the left side of the car. Match right side cam position to left side cam position.

Motor Gearing:
The gear charts on the following page show final drive ratio numbers for the TC6.2. Refer to motor manufacturer’s suggested gear
ratio for starting point. You may need to adjust the gearing according to your track size.

The following formula’s can also be helpful in determining final drive ratios and pinion size.

TC6 Internal Ratio = 2.0

Final Drive Ratio = (# of Teeth Spur) x (Internal Ratio)

# of Teeth on Pinion

# of Teeth on Pinion = (# of Teeth on Spur) x (Internal Ratio)

Final Drive Ratio
 29
:: Gear Chart 48 Pitch

!
Blank spaces in the gear
charts designates a gear
ratio that will not fit in the
vehicle. Gear fitment will
also depend on the motor
brand.

:: Gear Chart 64 Pitch

30
:: Shocks :: CVA’s
5407 Red O-Rings 8 31237 CVA Pin Retaining Clip 2
6465 Shock Piston, PTFE 12 31328 31238 CVA Bone Blade 8
6475 Preload Spacers, Collars, Cups 1 31366 TC6.1 CVA Kit 1
31305 Turnbuckle Eyelet 14 31367 TC6.1 CVA Rebuild Kit 1
31323 VCS3 Shock Kit 1 31368 TC6.1 CVA Bone Pr.
31329
31324 VCS3 Shock Rebuild 1 31369 TC6.1 Stub Axle Pr.
31325 VCS3 Shock Body 2 31500 M3x2.5mm Set Screw 6
31326 VCS3 Shock Collar 2 31324
31327 VCS3 Shock Bottom Cap 2 31238
31367
31328 VCS3 Aluminum Cap Retainer 2
31329 VCS3 Shock Cap 4 31500
31330 VCS3 Shock Shaft 2
31510 M2x4mm BHCS 6 31325 31368
31369
:: Springs 31366
3941 TC Spring, Green, 12.0lbs Pr. 31327 31237
3942 TC Spring, Silver, 14.5lbs (Kit) Pr.
3943 TC Spring, Blue, 17.0lbs Pr. 31324
3944 TC Spring, Gold, 19.5lbs Pr. 5407
3945 TC Spring, Red, 22.0lbs Pr. 31324 :: Anti-Roll Bars
3946 TC Spring, Copper, 25.0lbs Pr. 8828 Anti-Roll Bar Cups, Set 1
3952 TC Spring, Purple, 30.0lbs Pr. 31327 31058 Anti-Roll Bar Ballstud,blue aluminum 2
3953 TC Spring, Yellow, 35.0lbs Pr. 31364 TC6.1 Anti-Roll Bar Wire, Set 1
3954 TC Spring, White, 40.0lbs Pr.
3988 TC Spring Set, 1 pr. each 1
31326 31365 TC6.1 Anti-Roll Bar Mounts 4
31500 M3x2.5mm Set Screw 6
31511 M2x5mm SHCS 6
31510 31326 31627 TC6.2 Anti-Roll Bar Tube 1
31628 TC6.2 Anti-Roll Bar Kit 1
6465

31324 Front 31500

3942 31500 31511
Rear 8828 31511
31628
3942 31365
31269
31364 31511
31330 31511
6475
31058 31365
31500
31500
31305 31364
31627
31628

:: Shock Fluid :: Turnbuckles

5420 10 Weight Silicone Shock Fluid 2oz. 1402 FT Blue Titanium Turnbuckles 1.375” Pr.
5421 20 Weight Silicone Shock Fluid 2oz. 1405 FT Blue Titanium Turnbuckle 1.875” Pr.
5422 30 Weight Silicone Shock Fluid 2oz. 1418 FT Blue Titanium Turnbuckle 0.825” Pr.
5423 40 Weight Silicone Shock Fluid 2oz. 31305 Turnbuckle Eyelet 14
5424 22.5 Weight Silicone Shock Fluid 2oz.
5425 80 Weight Silicone Shock Fluid 2oz.
5426 27.5 Weight Silicone Shock Fluid 2oz.
5427 15 Weight Silicone Shock Fluid 2oz. 31305 31305
5428 25 Weight Silicone Shock Fluid 2oz.
5429 35 Weight Silicone Shock Fluid 2oz. 1418
5430 45 Weight Silicone Shock Fluid 2oz.
5431 55 Weight Silicone Shock Fluid 2oz.
5432 32.5 Weight Silicone Shock Fluid 2oz.
5433 37.5 Weight Silicone Shock Fluid 2oz. 31305 31305
5434 42.5 Weight Silicone Shock Fluid 2oz.
5435 50 Weight Silicone Shock Fluid 2oz. 1402
5436 60 Weight Silicone Shock Fluid 2oz.
5437 70 Weight Silicone Shock Fluid 2oz.
5438 47.5 Weight Silicone Shock Fluid 2oz. 31305 31305
1405
 31
:: Front Spool
31162 Axle Shim Kit 1
31175 Oneway/Spool Pulley 1
31341
31339 TC6 Spool Kit 1 31162
31341 TC6 Spool Outdrives 4
31342 TC6 Spool Hub 1 31350
31350 M2.5x10mm FHCS 6 31175
31401 10 x 15mm Bearing 2
31510 M2x4mm BHCS 6
31615 TC6.2 Diff Bearing Cam Set 1
31401
31510
31342 31162

31341

31510
31615
31615 31401
31350

:: Rear Gear Differential

4675 M2.5 X .45 X 6 FHCS 6 31162 31348
31162 Axle Shim Kit 1
31344 TC6 Gear Diff 1 31349
31347
31345 TC6 Gear Diff Rebuild 1
31346 TC6 Gear Diff Outdrives 2
31401 31349
31347 TC6 Gear Diff Case, 1 31346 31615
O-Ring, Pulley
31348 31615
31348 TC6 Gear Diff Pins & Shims 1 31348 31347
31349 TC6 Gear Diff Seals 1 31349 31348
31401 10 x 15mm Bearing 2
31615 TC6.2 Diff Bearing Cam Set 1 31345 31349
31348 31348
31345
See page 30 for shock fluids for use
with the TC gear differential. 31345 31346
31345 4675

31348 31401
31349
31348 31348
31345 4675
31348 31162

:: Spur Gear Assembly

31160 3mm E-Clip 6
31162 Axle Shim Kit 1
31521 31160
31314 TC6 Spur Gear Hub 1
31315 TC6 Spur Gear Shaft 1 31162 31320
31319 TC6 Spur Clamping Ring 1 31331
31320 TC6 Spur Pulley (20T) 2
31331 4x8x3mm Flanged Bearing 2
31333 TC6 Spur Gear (87T/48P) 1 31333
31521 M2.5x0.5x8mm BHCS 6 31314
31530 M3x0.5x5mm BHCS 6
31319
31530

31530 31331
31320
31315
31162
31160 31521
32
:: Steering Bellcrank and Servo Mounts
7336 Steering Servo Mount Kit 1 31530
7337 .250” x.125” x.015” Washer 4 31609
25211 M3x10mm BHCS 20
31283 5mm Ballstud, long 6 31611 31403
31286 Aluminum Ballstud Washers, Set 1 31550 31530
31374 FT TiN 3.25mm Ballstud, short 2 31403 31608
31286
31403 4x7mm Bearing 2
31530 M3x5mm BHCS 6 31610
31532 M3x8mm BHCS 6
31540 M3x5mm FHCS 6
31550 FT M3 Locknut, blue aluminum 6 31403 7336
31608 TC6.2 Servo Mount Brace 1 31403
31609 TC6.2 Steering Bellcrank Post Set 1 31285 7337 31622
31610 TC6.2 Steering Bellcrank 1 25211 31609
31611 TC6.2 Steering Rack Set 1 89007
31622 TC6.2 Servo Mount Set 1 31374
89007 Steering Servo Horn & Ring 1 31532
31540
31540
31611 7336
31532
31283 31286 7337

:: Front Bumper
1736 FT Body Clips, short 6 1736
3897 Pivoting Body Mounts, Set 1
4673 M2.5x4mm BHCS 6 3897
25201 M3x8mm FHCS 20
25203 M3x12mm FHCS 20 25201 3897
31623 TC6.2 Bumper Set 1
31624 TC6.2 Foam Bumper 1 31625
31625 TC6.2 Body Post Set 1
1736

4673 31625
31623
31623

25203
31624 25201

25203

:: Front and Rear Shock Towers

1736 FT Body Clips, short 6 31531 1736
3897 Pivoting Body Mounts, Set 1
31250 Shock Bushing 4
3897
31280 5mm Ballstud, short 6 31250 31531
31286 Aluminum Ballstud Washers, Set 1
31530 M3x5mm BHCS 6
31531 M3x6mm BHCS 6 31625
31532 M3x8mm BHCS 6 31530 31604
31541 3897
31541 M3x6mm FHCS 6
31604 TC6.2 Front Shock Tower 1 31250
31605 TC6.2 Rear Shock Tower 1 31250 31530
31530
31613 TC6.2 Bearing Cap (A) 1
31280 1736
31614 TC6.2 Bearing Cap (B) 1 31531 31541
31625 TC6.2 Body Post Set 1 31286
31280 31625
31532
31613 31286
31531 31531 31531
31605
31530
31531 31250
31531 31614 31532
 33
:: Front Bulkhead
25227 M4x8mm Setscrew 20
25237 5x10mm Bearing 2 31621
31112 1/16” x 5/16” Dowel Pins 8
31162 Axle Shim Kit 1
31200 Wheelbase Shim Set 1 31200
31214 Caster Block Bushing Pr. 25227
31221 Inner Hinge Pin Set 1 31221
31222 Outer Hinge Pin Set 1
31234 Clamping Wheel Hex 4 31200
31280 5mm Ballstud, short 6 31621
31284 8mm Ballstud, long 6
31356 TC6.1 Front Arms Pr. 31356
31358 TC6.1 Caster Blocks Pr. 31612
31360 TC6.1 Steering Blocks Pr. 31284
31370 TC6.1 Axle Crush Tubes 4 31356
31510 M2x4mm BHCS 6
31511 M2x5mm SHCS 6
31280
31532 M3x8mm BHCS 6 31222
31540 M3x5mm FHCS 6 31358 31510
31612 TC6.2 Bulkhead 1
31621 TC6.2 Inner Hinge Pin Ball Set 1
91148 M4 Locknut, with flange and 8 31358 31214 31280
knurl 31540
31540
31360
31358
25237 25237
31532
31112
31214
31234
31370
31162
91148
31511

:: Rear Bulkhead
25227 M4x8mm Setscrew 20
25237 5x10mm Bearing 2
31112 1/16” x 5/16” Dowel Pins 8
31162 Axle Shim Kit 1
31284
31200 Wheelbase Shim Set 1
31221 Inner Hinge Pin Set 1 31286
31222 Outer Hinge Pin Set 1
31234 Clamping Wheel Hex 4
31283 5mm Ballstud, long 6
31284 8mm Ballstud, long 6
31612
31286 Aluminum Ballstud Washers, Set 1 25237 31359
31357 TC6.1 Rear Arms Pr. 31370
31359 TC6.1 Rear Hub Carrier Pr. 31359
31370 TC6.1 Axle Crush Tubes 4
31162
31510 M2x4mm BHCS 6
31511 M2x5mm SHCS 6
31359
31540 M3x5mm FHCS 6 31234
31612 TC6.2 Bulkhead 1 25237
31540
31621 TC6.2 Inner Hinge Pin Ball Set 1
91148 M4 Locknut, with flange and 8 31540 31621 31112
knurl 31200
25227 31511 91148
31283
31357
31510

31222

31221
31357
31621 31200
34
:: Motor Mount / Battery Mount
31286 Aluminum Ballstud Washers, Set 1
31532 M3x8mm BHCS 6
31540 M3x5mm FHCS 6
31541 M3x6mm FHCS 6
31616 TC6.2 Spur Gear Bulkhead 1
31617 TC6.2 Motor Mount Set 1 31617
31626 TC6.2 LiPo Brace Set 1 31532 31616

31540 31616
31626
31286
31541 31617
31626
31541
31540
31532
31541 31540
31541

:: Chassis / Top Plate / Belts / Antenna / Arm Mounts

4617 Front Bulkhead Shim Set 1
6338 Antenna Tube 12”, black 1
31530
31187 Front Belt 1
31188 Rear Belt 1
31500 M3x2.5mm Set Screw 6
31530 M3x5mm BHCS 6
31540 M3x5mm FHCS 6 31530
31541 M3x6mm FHCS 6
31600 TC6.2 Chassis 1
31601 TC6.2 Top Plate 1
31618 TC6.2 Outer Arm Mount 1
31619 TC6.2 Inner Arm Mount 1 31530 31601
31620 TC6.2 Arm Mount Insert Set 1
31626 TC6.2 LiPo Brace /Antenna Mount Set 1

31188
31619
31620

4617
4617 31187
31541
31620 31500
31541
6338
31620

4617 31618 31600

31626
31541 4617 31626

31541
31540
 35
:: Pinions / Spur Gears :: Lubes & Adhesives
8253 16T 48P Pinion Gear 1 3921 69T 48P Spur Gear 1 1105 FT Green Slime Shock Lube 1
8254 17T 48P Pinion Gear 1 3922 72T 48P Spur Gear 1 1596 FT Locking Adhesive 1
8255 18T 48P Pinion Gear 1 3923 75T 48P Spur Gear 1 1597 FT Tire Adhesive, medium 1
8256 19T 48P Pinion Gear 1 3924 66T 48P Spur Gear 1 6588 Black Grease - 4cc 1
8257 20T 48P Pinion Gear 1 3994 73T 48P Spur Gear 1 6591 S.Diff Lube - 4cc 1
8258 21T 48P Pinion Gear 1 4462 100T 64P Spur Gear 1 6636 Silicone Grease - 4cc 1
8259 22T 48P Pinion Gear 1 4615 96T 64P Spur Gear 1 6727 Servo Tape 2
8260 23T 48P Pinion Gear 1 31332 80T 48P Spur Gear 1 9787 Chassis Protective Sheet 1
8261 24T 48P Pinion Gear 1 31333 87T 48P Spur Gear 1
8263 26T 48P Pinion Gear 1 31334 106T 64P Spur Gear 1
8264
8265
27T
28T
48P
48P
Pinion
Pinion
Gear
Gear
1
1
31335 115T 64P Spur Gear 1 :: Decals
716 Reedy 2009 Sticker Set 1
8266 29T 48P Pinion Gear 1
3816 American Bumper Sticker 1
8267 30T 48P Pinion Gear 1
3820 AE Logo Decal Sheet 1
8268 31T 48P Pinion Gear 1
3834 AE Blue Embossed Logo Sticker 2
8269 32T 48P Pinion Gear 1
31642 TC6.2 Decal Sheet 1
8270 33T 48P Pinion Gear 1
8271 34T 48P Pinion Gear 1
8272 35T 48P Pinion Gear 1
:: XP Electronics
29138 XP SC500 Brushless ESC 1
29139 XP SC900-BL ESC 1
:: Factory Team and Option Parts 29141 XP SC450-BL Brushless ESC 1
1401 FT Blue Titanium Turnbuckle 1.300” 2 29142 XP ESC Fan Option 1
1404 FT Blue Titanium Turnbuckle 1.775” 2 29143 XP SC700-BL Brushless ESC 1
1734 FT Blue Body Clip, 4 long, 6 short 10 29144 XP SC1200 Brushless ESC 1
1735 FT Blue Body Clip, long 4 29166 XP DS1313 Digital Servo 1
1736 FT Blue Body Clip, short 6 29167 XP DS1015 Digital Servo 1
3927 Radial Heatsink, narrow 1 29168 XP DS1510MG Servo 1
3928 Radial Heatsink, wide 1 29209 Gear Set, DS1313 1
3991 TC Aero Dish Wheel 24mm 4 29210 Gear Set, DS1015 1
4617 12R5 Front Bulkhead Shims (0.5, 1.0, 2.0)mm 4 ea 12 29211 Servo Case , DS1313/DS1015 1
6463 1:10 Blank Shock Pistons 8 29212 Accessory Pack, DS1313/DS1015 1
25391 FT 4mm Locknuts, blue 10 29214 TRS 403-SSi Receiver 1
31280 5mm Ballstud, short 6 29215 XP2G Radio System 1
31281 8mm Ballstud, short 6 29216 XP3G Radio System 1
31282 10mm Ballstud, short 6 29250 XP DS1505 Servo 1
31283 5mm Ballstud, long 6 29251 XP DS1505MG Servo 1
31284 8mm Ballstud, long 6 29252 XP DS1505 Metal Gear Set 1
31285 10mm Ballstud, long 6 29253 XP DS1510 Metal Gear Set 1
31286 Aluminum Ballstud Washer, Set 1 29254 Receiver Antenna 1
31288 Ti Nitride Ballstuds 5mm, short 2
31289 Ti Nitride Ballstuds 8mm, short 2
31290 Ti Nitride Ballstuds 10mm, short 2 :: Reedy Motors
31291 Ti Nitride Ballstuds 5mm, long 2 228 Sonic 540 Mach 2 25.5 Comp. Brushless Motor 1
31292 Ti Nitride Ballstuds 8mm, long 2 231 Sonic 540 Mach 2 21.5 Comp. Brushless Motor 1
31293 Ti Nitride Ballstuds 10mm, long 2 232 Sonic 540 Mach 2 17.5 Comp. Brushless Motor 1
31296 TC6 Ballast Weight 1 233 Sonic 540 Mach 2 13.5 Comp. Brushless Motor 1
31339 TC6 Spool Kit 1 234 Sonic 540 Mach 2 10.5 Comp. Brushless Motor 1
31344 TC6 Gear Differential Kit 1 235 Sonic 540 Mach 2 9.5 Comp. Brushless Motor 1
31441 10-Spoke Wheel, black 2 236 Sonic 540 Mach 2 8.5 Comp. Brushless Motor 1
31442 5-Spoke Wheel, black 2 237 Sonic 540 Mach 2 8.0 Comp. Brushless Motor 1
31443 5-Spoke Wheel, white 2 238 Sonic 540 Mach 2 7.5 Comp. Brushless Motor 1
31550 M3 Aluminum Lock Nut, blue 6 239 Sonic 540 Mach 2 7.0 Comp. Brushless Motor 1
31551 M4 Aluminum Flange Lock Nut, blue 6 240 Sonic 540 Mach 2 6.5 Comp. Brushless Motor 1
31629 TC6.2 Arm Mount Shims (outer) 4ea. 241 Sonic 540 Mach 2 6.0 Comp. Brushless Motor 1
31630 TC6.2 Arm Mount Shims (inner) 2ea. 242 Sonic 540 Mach 2 5.5 Comp. Brushless Motor 1
31632 TC6.2 DCV Kit, builds 2 DCV’s 1 243 Sonic 540 Mach 2 5.0 Comp. Brushless Motor 1
(requires #91156 Bearings, 5 x 10 x 3) 244 Sonic 540 Mach 2 4.5 Comp. Brushless Motor 1
31633 TC6.2 DCV Rebuild Kit 1 245 Sonic 540 Mach 2 4.0 Comp. Brushless Motor 1
31634 TC6.2 DCV Stub Axle 1 246 Sonic 540 Mach 2 3.5 Comp. Brushless Motor 1
31635 TC6.2 DCV Bone 1 954 Sonic 540 Stock Rotor 12.3 x 24.2 (7.25) 1
31636 TC6.2 DCV Coupler Tube 1 955 Sonic 540 Stock Rotor 12.3 x 25.0 (7.25) 1
31637 TC6.2 Gear Diff Outdrive, Steel 1 956 Sonic 540 Stock Rotor 12.5 x 25.0 (7.25) 1
31638 TC6.2 Spool Outdrive, Steel 1 957 Sonic 540 Modified Rotor 12.2 x 25.0 (5.0) 1
31639 TC6.2 Belt Tensioner Kit 1 958 Sonic 540 Modified Rotor 12.5 x 25.0 (5.0) 1
31640 TC6.2 Fan Mount Set 1 987 Sonic 540 Modified Rotor 13.0 x 25.0 (5.0) 1
31641 TC6.2 30mm Cooling Fan 1
91156 Bearing, 5 x 10 x 3, metal (used with #31632) 2
36
:: Reedy Batteries and Chargers :: Qualifier Series Vehicles
302 AA Alkaline 1.5V (4) 1 7052 Pro Lite 4x4 RTR, 1/10 Scale (ready-to-run) 1
304 LiPo Pro TX/RX Battery 1600mAh 7.4V Flat 1 20111 Rival Mini Monster Truck 1/18 Scale (ready-to-run) 1
305 LiFe Pro TX/RX Battery 1300mAh 6.6V Flat 1 20119 APEX Mini Touring RTR 1
309 LiPo 65C 7000mAh 7.4V 1 20510 RIVAL Electric Monster Truck RTR, 1/8 Scale 1
313 LiPo 65C 7000mAh 7.4V (5mm) 1 (ready-to-run)
602 LiPo 65C 4100mAh 7.4V Shorty 1 30112 APEX Touring V-Type, 1/10 Scale (ready-to-run) 1
604 526-S AC/DC 2S-6S LiPo/LiFe Charger 1
632 LiPo TX Lightweight Battery 1350mAh 11.1V 1
637 LiPo TX Battery - M11X 2500mAh 7.4V 1
736 Wolfpack LiPo 5000mAh 7.4V 25C 1
738 Wolfpack LiPo 3800mAh 7.4V 25C Shorty 1
739 Wolfpack LiPo 5500mAh 7.4V 60C 1

:: Reedy Accessories
233S Sonic 540/540 Mach 2 Stator 13.5 1
247 Sonic 540 Mach 2 Sensor w/bearing 1
248 Sonic 540 Mach 2 Steel Bearing Set 1 :: 1/18 Kits and RTR’s
249 Sonic 540 Mach 2 Ceramic Bearing Set 1 20103 RC18B2 - RC18T2 Team Kit 1
250 Sonic 540 Mach 2 Insulator Set 1 20121 SC18 RTR Brushless (ready-to-run) 1
605 Motor Cooling Fans (2) 1
607 Charge Harness 2S Standard Pack 4mm 1
654 4.0mm Bullet Plugs (2M, 2F) 1
655 4.0mm Bullet Plugs (2M, 10F) 1
656 4.0mm Bullet Plugs (10F) 1
657 4.0mm Bullet Plugs (100F) 1
658 4.0mm Bullet Plugs (10M) 1
659 4.0mm Bullet Plugs (30M) 1
669 5mm Bullet Connector 2
941S Sonic 540/540 Mach 2 Stator 17.5 1
959 Sonic 540/550 Sensor w/Bearing 1
960 Sonic 540/550 Insulator Set (2 pcs.) 1
961 Sonic 540/550 Timing Cap w/Screws 1
962 Sonic 540/540 Mach 2 Case Screws (3 pcs.) 1
972 Sonic 540 Steel Bearing Set 1
973 Sonic 540 Ceramic Bearing Set 1
978 Flat Sensor Wire 70mm 1
979 Flat Sensor Wire 110mm 1 :: 1/12, 1/10 Kits and RTR’s
980 Flat Sensor Wire 150mm 1
4020 FT 12R5.2 Kit 1
981 Flat Sensor Wire 200mm 1
6001 RC10 Classic Kit 1
982 Flat Sensor Wire 270mm 1
7025 FT RC10T4.2 Kit 1
992 Sonic 540 Rotor Spacers 1
7029 SC10 Associated/RC10.com Truck RTR (ready-to-run) 1
7030 SC10 KMC Wheels Race Truck RTR (ready-to-run) 1
7038 FT SC10.2 Kit 1
:: RePlay Cameras 7039 RC10T4.2 RS RTR 2.4GHz Brushless (ready-to-run) 1
7046 SC10 RS RTR, Lucas Oil (ready-to-run) 1
RP001 Replay XD1080 Complete Camera System 1
7049 SC10 RS RTR, Rockstar/Makita (ready-to-run) 1
RP002 Replay XD720 Complete Camera System 1
7050 SC10 RS RTR, Hart and Huntington (ready-to-run) 1
RP021 Replay XD1080 Lens Bezel Kit 1
7051 SC10 RS RTR, Lucas Slick Mist® Body 1
RP022 Replay XD1080 Clear Lens Cover 1
7054 SC10 RS RTR, Toyota Racing/TRD 1
RP023 Replay XD1080 Lens Bezel & Rear Cap O-Ring 1
7055 SC10 RS RTR, Monster Energy Toyota 1
RP024 Replay XD Lens Bezel 1
7093 SC10GT RTR (ready-to-run) 1
RP029 Replay XD1080 HDMI to Mini-HDMI 1
8020 FT RC10R5 Kit 1
RP030 Replay XD1080 Mini 8-pin USB Charge Data Cable 1
8022 FT RC10R5.1 Kit 1
RP032 USB DC Car Charger 1A Stubby 1
9040 FT RC10B4.1 Worlds Kit 1
RP033 USB DC Car Charger 500mAh 1
9041 FT RC10B4.2 Kit 1
RP034 Micro SDHC USB Reader 1
9042 RC10B4.2 RS RTR 2.4GHz Brushless (ready-to-run) 1
RP036 3M VHB 4991 Mount Adhesive for SnapTray 1
9050 SC10B RS RTR (ready-to-run) 1
RP038 3M VHB 5962 Mount Adhesive for SnapTray 1
9062 FT B44.2 4WD Buggy Kit 1
RP041 Replay XD Suction Cup Arm Mini Clamp 1
30101 TC4 Club Racer 4WD Touring Car Race Roller 1
RP042 Replay XD Suction Cup Short Arm Base 1
30109 FT TC6.2 WC 4WD Touring Car Kit 1
RP043 Replay XD Skateboard Mount 1
90005 SC10 4x4 Lucas Oil RTR (ready-to-run) 1
RP044 Replay XD VHB SnapTray, Convex 1
90006 SC10 4x4 Pro Comp RTR (ready-to-run) 1
RP045 Replay XD VHB SnapTray, Flat 1
90008 Limited Edition SC10 4x4 RTR Monster Energy 1
RP046 Au Plug for Universal DC Wall Charger 1
90010 SC10 4x4 FT Kit 1
RP047 Eu Plug for Universal DC Wall Charger 1
RP048 Uk Plug for Universal DC Wall Charger 1
RP049 Universal USB DC Wall Charger 1A 1
RP054 Replay ReView Field Monitor 1
 37
:: 1/8 Kits and RTR’s :: Apparel
20501 MGT 4.60 SE RTR (ready-to-run) 1 SP31** 27 Time WC T-Shirt, Black (S, M, L, XL, 2XL, 3XL) 1
20502 MGT 8.0 Nitro RTR (ready-to-run) 1 SP32** Kids AE 2012 T-Shirt, Blue (S, M, L) 1
20503 Limited Edition MGT 4.60 Nitro RTR, w/flag body 1 SP37** Reedy 2012 T-shirt - Black (S, M, L, XL, 2XL, 3XL) 1
(ready-to-run) SP38 Reedy Trucker Hat 1
20504 Limited Edition MGT 8.0 Nitro RTR, w/flag body 1 SP39 Reedy Patch 1
(ready-to-run) SP71** Associated Winter Jacket (M, L, XL) 1
80906 RC8.2 Nitro Buggy FT Kit 1 SP77** AE 2012 T-Shirt, Blue (S, M, L, XL, 2XL, 3XL) 1
80907 RC8.2e Electric Buggy FT Kit 1 SP78** AE 2012 T-Shirt, White (S, M, L, XL, 2XL, 3XL) 1
80908 RC8.2e Electric Buggy RTR (ready-to-run) 1 SP79** AE 2012 T-Shirt, Black (S, M, L, XL, 2XL, 3XL) 1
80909 RC8.2RS Nitro Buggy RTR (ready-to-run) 1 SP84** Reedy 3D T-Shirt, Black (S, M, L, XL, 2XL, 3XL) 1
80912 RC8T Championship Edition 1 SP86** Reedy Womens 3D T-Shirt, Black (S, M, L, XL) 1
80933 SC8.2e Short Course Race Truck, Rockstar/Makita 1 SP90** AE Retro T-Shirt, Blue (S, M, L, XL, 2-5XL) 1
Electric RTR (ready-to-run) SP91** AE Retro T-Shirt, Black (S, M, L, XL, 2-5XL) 1
80934 SC8.2e Short Course Race Truck, Slick Mist Electric 1 SP92** AE Retro T-Shirt, White (S, M, L, XL, 2-5XL) 1
RTR (ready-to-run) SP93** 2013 Worlds T-Shirt, Blue (S, M, L, XL, 2-5XL) 1
SP94** 2013 Worlds T-Shirt, Black (S, M, L, XL, 2-5XL) 1
SP95** 2013 Worlds Hoodie, Black (S, M, L, XL, 2-3XL) 1
:: Tools SP96** AE Retro Womens T-Shirt, Pink (S, M, L, XL) 1
SP97** AE Womens T-Shirt, Black (S, M, L, XL) 1
1111 FT Turnbuckle Wrench 1 SP98 AE Trucker Hat 1
1112 FT 4mm Turnbuckle Wrench 1 SP99 AE Patch 1
1450 FT On Road Ride Height Gauge 1 SP411S AE Hat 11’ Flat Bill Black S/M 1
1541 FT Hex Driver Set, (7 pcs) 1 SP411L AE Hat 11’ Flat Bill Black L/XL 1
1542 FT .050” Silver Hex Driver 1 SP416 Associated Car Carrier Bag, Medium 1
1543 FT 1/16” Black Hex Driver 1 SP417 1/10 FT Motor Bag 1
1544 FT 1.5mm Purple Hex Driver 1 SP420** AE Pit Gloves (L, XL) Pr.
1545 FT 5/64” Blue Hex Driver 1 SP421S AE 2012 Hat, Black, Flat Bill, S/M 1
1546 FT 3/32” Gold Hex Driver 1 SP421L AE 2012 Hat, Black, Flat Bill, L/XL 1
1547 FT 2.5mm Green Hex Driver 1 SP422S AE 2012 Hat, Black, Curved Bill, S/M 1
1548 FT 3mm Red Hex Driver 1 SP422L AE 2012 Hat, Black, Curved Bill, L/XL 1
1553 FT Phillips Silver Screwdriver 1 SP423S AE 2012 Hat, White, Flat Bill, S/M 1
1554 FT Silver Spring Hook Tool 1 SP423L AE 2012 Hat, White, Flat Bill, L/XL 1
1561 FT Nut Driver Set, (6 pcs) 1 SP424S AE 2012 Hat, White, Curved Bill, S/M 1
1562 FT 3/16” Black Nut Driver 1 SP424L AE 2012 Hat, White, Curved Bill, L/XL 1
1563 FT 1/4” Red Nut Driver 1 715 Reedy 2009 Track Banner 1
1564 FT 5.5mm Red Nut Driver 1 110684 Team Associated Track Banner 1
1565 FT 11/32” Green Nut Driver 1
1567 FT 8mm Gold Nut Driver 1
1589 FT 5/64” Blue Ball Hex Driver 1
1590 FT 3/32” Gold Ball Hex Driver 1
1592 FT Ball Hex Driver Set, (3 pcs) 1
1655 FT 8-Piece 1/4” Hex Drive Set 1
1656 FT 1/4” Hex Drive Handle, without tips 1
1657 FT 1/4” Hex Drive .050” Tip 1
1658 FT 1/4” Hex Drive 1/16” Tip 1
1659 FT 1/4” Hex Drive 5/64” - 2.0mm Tip 1
1660 FT 1/4” Hex Drive 3/32” Tip 1
1661 FT 1/4” Hex Drive 1.5mm Tip 1
1662 FT 1/4” Hex Drive 2.5mm Tip 1
1663 FT 1/4” Hex Drive 3/16” Nut Driver Tip 1
1664 FT 1/4” Hex Drive 1/4” Nut Driver Tip 1
1665 FT 1/4” Hex Drive 11/32” Nut Driver Tip 1 :: Contact Information
1666 FT 1/4” Hex Drive 5.5mm Nut Driver Tip 1
1667 FT 1/4” Hex Drive 7.0mm Nut Driver Tip 1
Associated Electrics, Inc.
1668 FT 1/4” Hex Drive 8.0mm Nut Driver Tip 1 26021 Commercentre Drive
1669 FT 1/4” Hex Drive 5/64” - 2.0mm Ball End Tip 1
1670 FT 1/4” Hex Drive 3/32” Ball End Tip 1
Lake Forest, CA 92630-8853 USA
1671 FT 1/4” Hex Drive Standard Screwdriver Tip 1 http://www.TeamAssociated.com
1672 FT 1/4” Hex Drive Phillips Screwdriver Tip 1
1673 FT 1/4” Hex Drive 2.5mm Ball End Tip 1
http://www.RC10.com
1674 FT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm, 1 http://twitter/Team Associated
1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)
1719 FT Camber + Track Width Tool 1
http://bit.ly/AEonFacebook
1737 FT Body Scissors 1
3718 12 Inch Nylon Wire Ties 12
3719 6 Inch Nylon Wire Ties 12
call: (949) 544-7500
3720 8 Inch Nylon Wire Ties 12 fax: (949) 544-7501
3987 Composite Droop Gauge 1
6429 Shock Building Tool 1
Check out the following web sites for all
6956 Molded Tools, Set 1 of our electric kits, current products, new
7494 V2 Stamped Multi-tool 1
7709 4 Inch Nylon Wire Ties 12
releases, setup help, tips, and racing info!
www.TeamAssociated.com. - www.RC10.com
38
:: Notes
 Driver: Date:
Track: Event:
Setup Sheet Conditions: Rev.1
Front Alignment Rear
5.0mm Ride Height 5.2mm
-2 Deg Camber -2 Deg
3 4 Deg Caster N/A 3
2 2
1 1
N/A Rear Hub Toe 0 Deg
+ 0.5 Deg Toe (Total) -3 Deg
Wheelbase Wheelbase
0 Hex Spacing 0
1mm Wheelbase 1mm
Front

Rear
Steering Rack
Steering Rack
Silver + 1mm N/A
Ball & Shims
B Steering Block Position N/A
A
B
Black Steering Block Ball & Shims N/A
Notes: A
Steering Block
Suspension Geometry B
2B Shock Position 2B
- -
1 Camber Link Position 2A
Toe 0 Toe 0
+ Black + 2mm Inner Ball & Shims Black +1mm +
Silver Outer Ball & Shims Silver +2mm
1 Dot Outer Arm Mount Insert 1 Dot
4 0.5mm Outer Mount Shims 0.5mm
3 4
2 3
1 1 Dot Inner Arm Mount Insert 2
Outer Ball 1 Dot 1 Outer Ball
& Shims & Shims
0.5mm Inner Mount Shims 0.5mm
Camber Camber
6 Droop 5
0 - - 0
+

+
1.1mm (Yellow) Anti-Roll Bar 0.9mm (Blue)
Notes:
Shocks
40wt Oil 40wt
#2 Piston #2
25% Rebound 25%
C BA Silver Spring Silver ABC
Notes:
Hex Spacing Hex Spacing
Droop Differentials Droop
Spool Type Gear
Cam Position
Belt Tension Arm Mount Inserts
Number
Setting 40wt -3 DOT -2 DOT 1 DOT +2 DOT +3 DOT
Mid-Low Cam Position Mid-Low
Wheel Base Shims
1 16 8 Belt Tension Number 7
Notes: -1 ° -1/2 ° 0 ° +1/2 ° +1 °
Tires Negative to the inside of vehicle.
Mid-Low Mid-High Type Positive to the outside of vehicle. 1mm 2mm
Tire Diameter Transmitter Speed Control
Insert & Wheel Turning Circle: E.S.C. Type:
17 32
Additive & Amount Steering Expo: E.S.C. Settings:
Notes: Brake E.P. : Software Version:
View from left
Low High side of car Chassis Throttle Expo: Notes:
Motor Gearing Chassis: Battery Placement Body & Wing
/ Top Plate:
Notes: Notes: Notes: Notes: Notes:
:: For more setups, visit RC10.com and click on “Setup Sheets”
 40
:: Hardware - 1:1 Scale View
Cap Head (shcs) Flat Head (fhcs) Button Head (bhcs)

2x5mm (31511) 2.5x10mm (31350) 2x4mm (31510)

3x5mm (31540) 2x5mm (31511)

3x6mm (31541) 2.5x4mm (4673)

Setscrew
3x8mm (25201) 2.5x6mm (4675)
3x2.5mm (31500)
3x10mm (25202) 2.5x8mm (31521)
4x8mm (25227)
3x12mm (25203) 3x5mm (31530)
Ballstuds 3x16mm (25204) 3x6mm (31531)

(Ti Nitride 3.25mm short 31374) 3x8mm (31532)

Black 5mm short (31280) 3x10mm (25211)

(Ti Nitride 5mm short, 31288)
3x12mm (89202)
Silver 8mm short (31283)
(Ti Nitride 5mm long, 31291) 3x14mm (25187)
Shims and Washers
Black 8mm short (31281) 3x16mm (89203)
(Ti Nitride 8mm short, 31289) 1mm and 2mm
blue shims (31286)
Silver 8mm long (31284)
(Ti Nitride 8mm long, 31292) Ball Bearings
Diff washer (31166)
Black 10mm short (31285) 4x7mm (31403)
(Ti Nitride 10mm short, 31290)
1mm and 2mm
Silver 10mm long (31285) wheelbase shims (31200) 4x8x3mm flanged (31331)
(Ti Nitride 10mm long, 31293)

Thrust washer (6573) 5x8mm (31400)

Gold washer (7337) 5x10mm (25237)

Nuts (lock/plain)
Bulkhead Shim (4617)
2-56 locknut (3904) 0.5mm, 1mm, 2mm 10x15mm (31401)

M3 locknut (31550)
Diff shim (31162)
Clips
M4 locknut (91148)
3mm E-clip (31160)

C-clip (31307)

Notes:
 Driver: Date:
Track: Event:
Setup Sheet Conditions: Rev.1
Front Alignment Rear
Ride Height
Camber
3 Caster N/A 3
2 2
1 1
N/A Rear Hub Toe
Toe (Total)
Wheelbase Wheelbase
Hex Spacing
Wheelbase
Front

Rear
Steering Rack
Steering Rack
N/A
Ball & Shims
Steering Block Position N/A
A
B
Steering Block Ball & Shims N/A
Notes: A
Steering Block
Suspension Geometry B
Shock Position
- -
Camber Link Position
Toe 0 Toe 0
+ Inner Ball & Shims +
Outer Ball & Shims
Outer Arm Mount Insert
4 Outer Mount Shims
3 4
2 3
1 Inner Arm Mount Insert 2
Outer Ball 1 Outer Ball
& Shims & Shims
Inner Mount Shims
Camber Camber
Droop
0 - - 0
+

+
Anti-Roll Bar
Notes:
Shocks
Oil
Piston
Rebound
C BA Spring ABC
Notes:
Hex Spacing Hex Spacing
Droop Differentials Droop
Type
Cam Position
Belt Tension Arm Mount Inserts
Number
Setting -3 DOT -2 DOT 1 DOT +2 DOT +3 DOT
Cam Position
Wheel Base Shims
1 16 Belt Tension Number
Notes: -1 ° -1/2 ° 0 ° +1/2 ° +1 °
Tires Negative to the inside of vehicle.
Mid-Low Mid-High Type Positive to the outside of vehicle. 1mm 2mm
Tire Diameter Transmitter Speed Control
Insert & Wheel Turning Circle: E.S.C. Type:
17 32
Additive & Amount Steering Expo: E.S.C. Settings:
Notes: Brake E.P. : Software Version:
View from left
Low High side of car Chassis Throttle Expo: Notes:
Motor Gearing Chassis: Battery Placement Body & Wing
/ Top Plate:
Notes: Notes: Notes: Notes: Notes:
:: For more setups, visit RC10.com and click on “Setup Sheets”
 Associated Electrics, Inc.
26021 Commercentre Dr.
Lake Forest, CA 92630 USA
http://www.TeamAssociated.com
http://www.RC10.com
http://twitter/Team_Associated
http://bit.ly/AEonFacebook
call: (949) 544-7500 - fax: (949) 544-7501
Check out the following web sites for all of our kits,
current products, new releases, setup help, tips, and racing info!
www.TeamAssociated.com. - www.RC10.com