SERVICE & PARTS

MANUAL
LX 31/41
Electric & Bi-Energy Models
Serial Numbers 1000 to current

When contacting UpRight for service or parts

Stamped information, be sure to include the MODEL and
Serial Number SERIAL NUMBERS from the equipment name-
plate. Should the nameplate be missing, the
SERIAL NUMBER is also stamped on top of the
chassis above the front axle pivot.

UpRight, Inc. UpRight Ireland, Ltd.

1775 Park Street Pottery Road
Selma, California 93662 Dun Laoire
TEL: 559/891-5200 Ireland
Call Toll Free in U.S.A.
FAX: 559/891-9012 TEL: +353-1-202-4100
PARTS FAX: 559/896-9244 1-800-926-LIFT FAX: +353-1-202-4105
For Parts:
1-888-UR-PARTS 067448-020
B 9/99 K
 FORWARD
HOW TO USE THIS MANUAL
This manual is divided into 6 sections. The section
number printed at the top corner of each page can be Introduction &
used as a quick reference guide. Specifications 1.0
Special information General description and machine
specifications.
! D A N G E R !
Indicates the hazard or unsafe practice will
result in severe injury or death.
Machine Preparation &
Operation 2.0
! W A R N I N G ! Information on how to operate the work
Indicates the hazard or unsafe practice could platform and how to prepare it for operation.
result in severe injury or death.

! C A U T I O N ! Maintenance
Indicates the hazard or unsafe practice could
result in minor injury or property damage
Preventative maintenance and service 3.0
information.
NOTES: Give helpful information.
WORKSHOP PROCEDURES
CAUTION: Detailed descriptions of standard work- Troubleshooting
shop procedures, safety principles and service oper-
Causes and solutions to typical problems.
4.0
ations are not included. Please note that this manual
does contain warnings and cautions against some
specific service methods which could cause personal
injury, or could damage a machine or make it unsafe.
Please understand that these warnings cannot cover Schematics
all conceivable ways in which service, whether or not
recommended by UpRight, Inc., might be done, or of Schematics and valve block diagram with 5.0
the possible hazardous consequences of each con- description and location of components.
ceivable way, nor could UpRight Inc. investigate all
such ways. Anyone using service procedures or
tools, whether or not recommended by UpRight Inc.,
must satisfy themselves thoroughly that neither per-
sonal safety nor machine safety will be jeopardized. Illustrated Parts
All information contained in this manual is based on
the latest product information available at the time of
Breakdown 6.0
printing. We reserve the right to make changes at Complete parts lists with illustrations.
any time without notice. No part of this publication
may be reproduced, stored in retrieval system, or
transmitted, in any form by any means, electronic,
mechanical, photocopying, recording, or otherwise,
without the prior written permission of the publisher.
This includes text, figures and table.

LX31/41 Electric/Bi-Energy Work Platform i

 FORWARD

NOTES:

ii LX31/41 Electric/Bi-Energy Work Platform

 TABLE OF CONTENTS

Forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
How to Use This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . i Workshop Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Special information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i

SECTION 1
Introduction & Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.1 .Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.3 Purpose Of Equipment . . . . . . . . . . . . . . . . . . . . . . 1-1
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.4 Special Limitations . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.5 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.2 General Description. . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Elevating Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Control Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

SECTION 2
Machine Preparation & Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2.6 Raising the Platform . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2.2 Pre-Operation and Safety Inspection. . . . . . . . . . . 2-2 From the Platform Controls . . . . . . . . . . . . . . . . . . . . . 2-6
System Function Inspection . . . . . . . . . . . . . . . . . . . . . 2-2 From the Chassis Controls . . . . . . . . . . . . . . . . . . . . . 2-6
2.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 2.7 Lowering the Platform. . . . . . . . . . . . . . . . . . . . . . . 2-7
Travel With Platform Lowered . . . . . . . . . . . . . . . . . . . 2-4 From the Platform Controls . . . . . . . . . . . . . . . . . . . . . 2-7
Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 From the Chassis Controls . . . . . . . . . . . . . . . . . . . . . 2-7
Raising and Lowering the Platform . . . . . . . . . . . . . . . 2-4 Emergency Lowering . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Travel with Work Platform Elevated . . . . . . . . . . . . . . . 2-4 2.8 Design Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Emergency Lowering . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 2.9 Controls and Indicators . . . . . . . . . . . . . . . . . . . . . 2-8
After Use Each Day . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 2.10 Fold Down Guardrails . . . . . . . . . . . . . . . . . . . . . 2-10
Parking Brake Release . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Erection Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
2.4 Preparation for Shipment . . . . . . . . . . . . . . . . . . . . 2-6 Double Deck Fold Down Procedure . . . . . . . . . . . . . 2-11
2.5 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Erection Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
PRESERVATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

SECTION 3
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3.7 Battery Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Battery Inspection and Cleaning . . . . . . . . . . . . . . . . . 3-7
General Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3.8 Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.2 Date Code Identification on Hoses. . . . . . . . . . . . . 3-1 Grease Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.3 Special Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Steering Linkage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.4 Deutsch Connectors . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Torque Hubs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Male Connector (Plug) . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Hydraulic Oil And Filter . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Female Connector (Receptacle) . . . . . . . . . . . . . . . . . 3-3 Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Releasing Locking Fingers . . . . . . . . . . . . . . . . . . . . . . 3-3 Oil and Filter Replacement . . . . . . . . . . . 3-8
Crimping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 3.9 Setting Hydraulic Pressures. . . . . . . . . . . . . . . . . . 3-9
Removing Contact from Lift Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Heavy Duty Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Steering Relief Valves . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.5 Preventative Maintenance. . . . . . . . . . . . . . . . . . . . 3-4 3.10 Switch Adjustments . . . . . . . . . . . . . . . . . . . . . . 3-10
Preventative Maintenance Table Key . . . . . . . . . . . . . 3-5 Proportional Control Adjustment . . . . . . . . . . . . . . . . 3-10
Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Proportional Drive Control . . . . . . . . . . . . . . . . . . . . . 3-10
Preventative Maintenance Report . . . . . . . . . . . . . . . . 3-5 Platform Down Limit Switches . . . . . . . . . . . . . . . . . . 3-11
3.6 Blocking Elevating Assembly. . . . . . . . . . . . . . . . . 3-6 Tilt Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Brace Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Brace Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

LX31/41 Electric/Bi-Energy Work Platform I

 TABLE OF CONTENTS
3.11 Hydraulic Manifold . . . . . . . . . . . . . . . . . . . . . . . 3-12 3.16 Torque Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Cleaning and Inspection . . . . . . . . . . . . . . . . . . . . . . . 3-12 3.17 Torque Hub Seal Replacement . . . . . . . . . . . . . . 3-19
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 Roll And Leak Testing . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 Roll Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
3.12 Hydraulic Power Unit . . . . . . . . . . . . . . . . . . . . . 3-14 Leak Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Pressing Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
3.13 Hydraulic Brakes . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Main Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
Brake Seal Replacement . . . . . . . . . . . . . . . . . . . . . . 3-15 3.18 Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
3.14 Generator, Bi-Energy Models Only . . . . . . . . . . 3-16 Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Drive Belt Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 3-16 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16 3.19 Steering Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
3.15 Drive Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
Removal . . . . . . . . . . . . . . . . . . . . . . . . . 3-17 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
Installation . . . . . . . . . . . . . . . . . . . . . . . 3-17 3.20 Lift Cylinder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Pump Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Removal . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
3.21 Torque Specifications . . . . . . . . . . . . . . . . . . . . . 3-26
Installation . . . . . . . . . . . . . . . . . . . . . . . 3-17 Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Drive Motor Brushes . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17 Hydraulic Components . . . . . . . . . . . . . . . . . . . . . . . . 3-26

SECTION 4
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 4.5 Using the Calibrator . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
General Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 4.6 Calibrator Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
4.2 Troubleshooting Electrical Schematics . . . . . . . . 4-2 4.7 Upright Traction Controller display . . . . . . . . . . . . 4-7
4.3 Troubleshooting Hydraulic . . . . . . . . . . . . . . . . . . 4-5 4.8 MOS90 Fault Finding Flow Charts . . . . . . . . . . . . . 4-8
4.4 Troubleshooting the MOS90 . . . . . . . . . . . . . . . . . 4-6 4.9 ACTIVATING "TEST" . . . . . . . . . . . . . . . . . . . . . . . 4-14
When a Flash Error occurs . . . . . . . . . . . . . . . . . . . . . . 4-6
Step 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Step 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

SECTION 5
Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 5.3 Hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
5.1 Electrical Schematic, Bi-Energy . . . . . . . . . . . . . . 5-2 5.4 Component Identification . . . . . . . . . . . . . . . . . . . . 5-8
5.2 Electrical Schematic, Electric . . . . . . . . . . . . . . . . 5-4

SECTION 6
Illustrated Parts Breakdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

II LX31/41 Electric/Bi-Energy Work Platform

 LIST OF FIGURES

SECTION 1
Intr oduc tion & Spec ifica tio ns
Figure 1-1: Work Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

SECTION 2
Mac hi ne Pre pa ra ti on & Oper at io n
Figure 2-1: Chassis Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Figure 2-5: Parking Brake Release Button . . . . . . . . . . . . . . . . . . . . . 2-5
Figure 2-2: Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Figure 2-6: Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Figure 2-3: Tilt Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Figure 2-7: Fold Down Guardrails . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Figure 2-4: Emergency Lopwering Knob . . . . . . . . . . . . . . . . . . . . . . 2-5 Figure 2-8: Fold Down Guardrails (Double Deck) . . . . . . . . . . . . . . 2-11

SECTION 3
Maintenance
Figure 3-1: Deutsch Connector Kit, Small . . . . . . . . . . . . . . . . . . . . . 3-2 Figure 3-14: Tilt Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Figure 3-2: Deutsch Connector Kit, Large . . . . . . . . . . . . . . . . . . . . . 3-2 Figure 3-15: Hydraulic Manifold, Exploded View . . . . . . . . . . . . . . . 3-13
Figure 3-3: Plugs and Receptacles, Deutsch Connectors . . . . . . . . . . 3-2 Figure 3-16: Hydraulic Power Unit . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Figure 3-4: Locking Finger, Deutsch Connector . . . . . . . . . . . . . . . . . 3-3 Figure 3-17: Rear Axle Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Figure 3-5: Heavy Duty Deutsch Connector . . . . . . . . . . . . . . . . . . . . 3-3 Figure 3-18: Brake Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Figure 3-6: Blocking Elevating Assembly . . . . . . . . . . . . . . . . . . . . . . 3-6 Figure 3-19: Engine, Generator, and Drive Belt Adjustments . . . . . . 3-16
Figure 3-7: Lubrication Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Figure 3-20: Fuel Tank, Bi-Energy Models . . . . . . . . . . . . . . . . . . . . 3-16
Figure 3-8: Hydraulic Oil Tank and Filter . . . . . . . . . . . . . . . . . . . . . . 3-8 Figure 3-21: Replacing Drive Motor Brushes . . . . . . . . . . . . . . . . . 3-17
Figure 3-9: Hydraulic Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Figure 3-22: Torque Hub Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Figure 3-10: Valve Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Figure 3-23: Measuring Hub End Play . . . . . . . . . . . . . . . . . . . . . . . 3-20
Figure 3-11: Flow Meter Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Figure 3-24: Torque Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Figure 3-12: Rotary Control Adjustment, Upper Control Box . . . . . . 3-10 Figure 3-25: Steering Cylinder Cross Section . . . . . . . . . . . . . . . . . 3-24
Figure 3-13: Platform Down Limit Switch . . . . . . . . . . . . . . . . . . . . 3-11 Figure 3-26: Lift Cylinder Cross Section . . . . . . . . . . . . . . . . . . . . . 3-25

SECTION 4
Troubleshooting
Figure 4-1: MOS90 Calibrator LED Segments . . . . . . . . . . . . . . . . . . 4-6 Figure 4-3: Upright Tachometer Board . . . . . . . . . . . . . . . . . . . . . . 4-15
Figure 4-2: MOS90 17 Way Connector Pinout Designation . . . . . . . 4-14

SECTION 5
Sc he mat ic s
Figure 5-1: Electrical Schematic - 067447-002 . . . . . . . . . . . . . . . . . 5-3 Figure 5-6: Lower Control Box Relays . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Figure 5-2: Electrical Schematic - 067447-003 . . . . . . . . . . . . . . . . . 5-5 Figure 5-7: Relay Panel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Figure 5-3: Hydraulic Schematic - 067446-000 . . . . . . . . . . . . . . . . . 5-7 Figure 5-8: Engine Relays (Bi-Energy) . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Figure 5-4: Lower Control Box Assembly . . . . . . . . . . . . . . . . . . . . . . 5-8 Figure 5-9: Valve Manifold, Exploded View . . . . . . . . . . . . . . . . . . . . 5-9
Figure 5-5: Upper Control Box Assembly . . . . . . . . . . . . . . . . . . . . . . 5-8 Figure 5-10: Brake Valve Manifold, Exploded View . . . . . . . . . . . . . . 5-9

LX31/41 Electric Work Platform III

 LIST OF TABLES

SECTION 1
Int roduc tion & Spe cific at io ns
Table 1-1: Work Platform Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

SECTION 2
Mac hi ne Pr epara ti o n & O per at i on
Table 2-1: Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

SECTION 3
Maintenance
Table 3-1: Preventative Maintenance Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Table 3-2: Torque Specifications for Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Table 3-3: Torque Specifications for Hydraulic Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26

SECTION 4
Tr oublesho ot ing
Table 4-1: Trouble Shooting Guide: Electrical Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Table 1: Troubleshooting Guide: Hydraulic Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Table 4-2: Calibrator Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Table 4-3: Calibrator Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

SECTION 5
Sc he mat ic s
Table 5-1: Electrical Schematic - 067447-002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Table 5-2: Electrical Schematic, 067447-003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Table 5-3: Hydraulic Schematic - 067446-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

IV LX31/41 Electric/Bi-Energy Work Platform

 Section 1
I N T RO D U C T I O N & S P E C I FI C A T I O N S

1.1 .INTRODUCTION Control Module

Purpose The control module contains the hydraulic valve man-
ifold, horn/alarms, volt/hour meter, electrical terminal
The purpose of this service and parts manual is to strips, batteries, and chassis control panel. A com-
provide instructions and illustrations for the operation plete explanation of the chassis control functions is
and maintenance of the Work Platform manufactured found in Section 2.
by UpRight, Inc. of Selma, California.
Chassis
Scope The chassis is a structural frame that supports all the
The manual includes procedures for proper opera- components of the LX 31/41 Work Platform.
tion, maintenance, adjustment, and repair of this
product as well as recommended maintenance 1.3 PURPOSE OF EQUIPMENT
schedules and troubleshooting.
The objective of the LX 31/41 Work Platform is to
1.2 GENERAL DESCRIPTION provide a quickly deployable, self propelled, variable
height work platform to elevate personnel and materi-
The LX 31/41 Work Platform consists of the platform, als to overhead work areas and be driven over nor-
controller, elevating assembly, power module, control mal terrains.
module, and chassis.
1.4 SPECIAL LIMITATIONS
Platform
Travel with the platform raised is limited to a creep
The platform has a reinforced steel floor, 1.11 m
speed range.
(43.5 inch) high guardrails with midrail, 152 mm (6
inch) toeboards and an entrance gate at the rear of Elevating of the Work Platform is limited to firm, level
the platform. The guardrails can be folded down for surfaces only. Any degree of slope greater than 2°
access through doors or for shipment. will lockout the elevating circuits and sound a warning
alarm.
Machine will not drive when elevated above 8 m.
! W A R N I N G !
DO NOT use the maintenance platform without
guardrails properly assembled and in place. ! D A N G E R !
The elevating function shall ONLY be used when
Controller the work platform is level and on a firm surface.
The controller contains the controls to operate the The work platform is NOT intended to be driven
machine. It should be hung on the front, left, or right over uneven, rough or soft terrain when elevated
guardrail, but may be hand held if necessary. To
operate the machine, the interlock lever must be 2
depressed to operate any function. A complete
explanation of control functions can be found in Sec-
tion 2.
1
Elevating Assembly
The platform is raised and lowered by the elevating
assembly; a three (LX 31), or four (LX41) section
scissor assembly powered by a single stage lift cylin-
der. The hydraulic pump, driven by the batteries, 4 5
powers the cylinder. Solenoid operated valves control 3 6
raising and lowering.
1. Platform 3. Elevating 5. Control Module
Assembly
Power Module 2. Controller
Assembly 4. Power Module
6. Chassis

The power module contains the batteries, hydraulic

pump, and hydraulic reservoir. Figure 1-1: Work Platform

LX31/41 Electric/Bi-Energy Work Platform 1-1

 Section
1.5 I N T RO D U C T I O N & S P E C I FI C A T I O N S

1.5 SPECIFICATIONS
Table 1-1: Work Platform Specifications

ITEM LX31 LX41

Platform Size (Inside Toeboards)
Standard 3.64 m x 1.78 m [143.38 in. x 70 in. 3.64 m x 1.78 m [143.38 in. x 70 in.]
w/ Extension 4.56 m x 1.73 m [179.38 in. x 68 in.] 4.56 m x 1.73 m [179.38 in. x 68 in.]
DoubleDeck Models
w/ Decks Retractedd 3.96 m x 1.73 m [156 in. x 68 in.] 3.96 m x 1.73 m [156 in. x 68 in.]
w/ Decks Extended 5.79 m x 1.73 m [228 in. x 68 in.] 5.79 m x 1.73 m [228 in. x 68 in.]
Max. Platform Capacity
Standard 907 kg [2000 lbs.] 680 kg [1,500 lbs.]
w/ Extension 907 kg [2000 lbs.] 680 kg [1,500 lbs.]
on Extension 227 kg [500 lbs.] 227 kg [500 lbs.]
Double Deck Models 795 kg [1750 lbs.] 567 kg [1,250 lbs]
on Extension (one end only) 227 kg [500 lbs.] 227 kg [500 lbs.]
Max. No. of occupants
Standard 8 people 6 people
on Extension 2 people 2 people
Double Deck Models 8 people 6 people
on Extension (one end only) 2 people 2 people
Height
Working Height 11.28 m [37 ft.] 14.33 m [47 ft.]
Max. Platform Height 9.45 m [31 ft.] 12.34 m [40 ft. 6 in.]
Min. Platform Height 1.43 m [56.3 in.] 1.66 m [65.3 in.]
Dimensions
Weight, Electric 2wd: 4,477 kg [9,870 lbs.] 2wd: 5,085 kg [11,210 lbs.]
BiEnergy 2wd: 4,568 kg [10,070 lbs.] 4wd: 5,176 kg [11,410 lbs.]
Electric w/ Extension 2wd: 4,672 kg [10,300 lbs.] 2wd: 5,280 kg [11,640 lbs.]
BiEnergy w/ Extension 2wd: 4,763 kg [10,500 lbs.] 4wd: 5,371 kg [11,890 lbs.]
Electric Double Deck 2wd: 4,866 kg [10,728 lbs.] 2wd: 5,474 kg [12,068 lbs.]
BiEnergy Double Deck 2wd: 4,957 kg [10,928 lbs.] 4wd: 5,565 kg [12,268 lbs.]
Overall Width 2.29 m [90 in.] 2.29 m [90 in.]
Overall Height 2.53 m [99.75 in.] 2.76 m [108.75 in.]
Overall Length, Standard 4.08 m [160.5 in.] 4.08 m [160.5 in.]
Driveable Height 8 m [26 ft. 2 in.] 8 m [26 ft. 2 in.]
Surface Speed
Platform Lowered 0 to 5.0 km/h [0 to 3.1 mph] 0 to 5.0 km/h [0 to 3.1 mph]
Platform Raised 0 to .48 km/h [0 to 0.3 mph] 0 to .48 km/h [0 to 0.3 mph]
System Voltage 48 Volt DC 48 Volt DC
Hydraulic Tank Capacity
Maximum Hydraulic System Pressure
Hydraulic Fluid
Normal use (>32 oF [0 oC]) ISO #46 ISO #46
Low Temp. Use (-10 to 32 oF [-23 to 0 oC]) 5W-20 Motor Oil 5W-20 Motor Oil
Lift System One Single Stage Lift Cylinder One Single Stage Lift Cylinder
Lift Speed Raise, 40 sec./Lower, 60 sec. Raise, 40 sec./Lower, 60 sec.
Eight 6V 350 AH Batteries Eight 6V 350 AH Batteries
Power Source
(BiEnergy) One Kubota 12 HP Diesel (BiEnergy) One Kubota 12 HP Diesel
Drive Control Proportional Proportional
Control System Smooth one hand Joystick Smooth one hand Joystick
Horizontal Drive Two Electric Wheel Motors Two Electric Wheel Motors
Tires Standard 10-16.5 NHS 8 Ply, 3.4 bar [50psi] 10-16.5 NHS 8 Ply, 3.4 bar [50psi]
Optional Poly Filled Poly Filled
Parking Brakes Two, Spring Applied, Hydraulic Release, Multiple Disc Two, Spring Applied, Hydraulic Release, Multiple Disc
Turning Radius (inside) 1.22 m [48 in.] 1.22 m [48 in.]
Maximum Gradeability 2wd: 30% [16.7º] 2wd: 30% [16.7º]
Wheel Base 2.94 m [115.75 in.] 2.94 m [115.75 in.]
Guardrails 1.1 m [43.5 in.] high, Fold Down with Self Closing Gate 1.1 m [43.5 in.] high, Fold Down with Self Closing Gate
Toeboard 152 mm [6 in.] High 152 mm [6 in.] High
NOTE:Specifications subject to change without notice.
Meets or Exceeds all applicable requirements of CE and GS.

1-2 LX31/41 Electric/Bi-Energy Work Platform

 Section 2
M A C H I N E P RE P A R A T I O N & O P E R A T I O N
Warning
All personnel shall carefully read, understand and follow all safety rules, operating instructions, and the Scaffold Industry
Association’s Manual of Responsibilities (ANSI A92.6) before operating or performing maintenance on any Upright

Safety Rules

NEVER operate the machine NEVER elevate or drive NEVER sit, stand or climb
within ten feet of power lines. elevated on uneven slopes or on guardrail or midrail
THIS MACHINE IS NOT soft ground or elevate the
INSULATED platform unless the platform
is level

NEVER operate the machine without first surveying the work area for surface hazards such as holes, drop-offs, bumps and debris.
NEVER operate the machine if all guardrails are not properly in place and secured with all fasteners properly torqued.
SECURE and lock gate after mounting platform.
KEEP all body parts clear of outriggers when extending or retracting (outrigger equipped machines only).
NEVER use ladders or scaffolding on the platform.
NEVER attach overhanging loads or increase platform size.
LOOK up, down and around for overhead obstructions and electrical conductors.
DISTRIBUTE all loads evenly on the platform. See the back cover for maximum platform load.
NEVER use damaged equipment. (Contact UpRight for instructions. See toll-free phone number on back cover.)
NEVER change operating or safety systems.
INSPECT the machine thoroughly for cracked welds, loose hardware, hydraulic leaks, damaged control cable, loose wire connec-
tions and wheel bolts.
NEVER climb down elevating assembly with the platform elevated.
NEVER perform service on machine while platform is elevated without blocking elevating assembly.
NEVER recharge battery near sparks or open flame; batteries that are being charged emit highly explosive hydrogen gas.
AFTER USE secure the work platform against unauthorized use by turning key switch off and removing key.
NEVER replace any component or part with anything other than original UpRight replacement parts without the manufacturer's con-
sent.

California Proposition 65 Warning

Gasoline and diesel engine exhaust and some of their constituents are known to the State of California to cause cancer,
birth defects, and other reproductive harm.

LX13/41 Electric/Bi-Energy Work Platform 2-1

 Section
2.1 M A C H I N E P RE P A R A T I O N &

2.1 INTRODUCTION System Function Inspection

This manual covers the Electric model of the LX
Series Work Platforms. This machine operates on a
48 volt battery powered system.
! W A R N I N G !
STAND CLEAR of the work platform while per-
forming the following checks.
! W A R N I N G ! Before operating the work platform survey the
work area for surface hazards such as holes,
DO NOT use a machine that is damaged or drop-offs, bumps and debris.
malfunctioning. Tag and remove the unit from
service until it is repaired. Check in ALL directions, including above the
work platform, for obstructions and electrical
conductors.
2.2 PRE-OPERATION AND SAFETY Protect control console cable from possible
INSPECTION damage while performing checks.
Carefully read, understand and follow all safety rules,
labels, and operating instructions, then perform the
Platform/
following steps each day before use. Emergency
Chassis/Brake
Stop Button
Perform a complete visual inspection of the entire Release
Switch
unit prior to operating.
1. Open panels and check hydraulic components
and hoses for damage or leaks. Check electrical
components and wiring for damage or loose con-
nections. Raise

2. Inspect chassis, axles, hubs, and steering linkage Hour Meter

for damage, deformation, buckeled paint, loose or Lower
missing hardware, and cracked welds.
3. With platform fully lowered, check the hydraulic
oil level sight gauge on the hydraulic tank . Add
ISO #46 hydraulic oil if necessary.
4. Check that fluid level in all batteries is correct
(See Battery Maintenance in Section 3). Brake
Release
5. Check that all guardrails are in place. Insure that
gate operates freely and latches securely. Figure 2-1: Chassis Control Panel
6. Check tires for damage. Check tire pressure; 5.2
bar (75 psi) if equipped with pneumatic tires.
7. Carefully inspect the entire work platform for
damage such as cracked welds or structural
members, loose or missing parts, oil leaks, dam-
aged cables or hoses, and loose connections.

2-2 LX13/41 Electric/Bi-Energy Work Platform

 Section
M A C H I N E P RE P A R A T I O N & 2.2
11. Lower the platform partially by pushing in on the
Interlock Lever
Steering Switch chassis lower switch, and check operation of the
audible lowering alarm.
Speed Range Switch
Control Lever 12. Open the chassis emergency lowering valve (Fig-
ure 2-4) to check for proper operation by pulling
Emergency
Stop Button and holding the knob out. Once the platform is
fully lowered, close the valve by releasing the
knob.
13. On chassis controls, turn key switch to platform.
Drive Enable
Indicator
14. Mount the platform making sure the gate is
latched.
15. Turn platform controller key switch clockwise to
ON. Position drive/lift switch to LIFT.
Lift/Drive Switch 16. Depress the interlock lever and slowly push the
control lever to RAISE to raise the platform, fully
Figure 2-2: Controller
actuate the control lever to check proportional lift
speed. Elevate the platform to 3.7 m (12 feet).
1. Unhook controller from guardrail. Firmly grasp 17. Slowly pull control lever to DOWN position to
controller handle in such a manner that the inter- lower platform. Check that lowering alarm
lock lever can be depressed, while performing the sounds.
following checks from the ground. 18. Turn platform controller key switch to OFF, push
2. Turn platform controller key switch clockwise to the emergency stop button and dismount the
ON. platform.
3. Position drive/lift switch to DRIVE position. Drive 19. Close and secure module covers.
enable indicator light will be illuminated.
4. With the speed range switch first in LOW SPEED
and then again in HIGH SPEED depress the
interlock lever and slowly push the control lever to
FORWARD then REVERSE positions to check Tilt Sensor
for speed and directional control. The farther you
push or pull the control lever the faster the
machine will travel.
5. Push steering switch RIGHT then LEFT to check
for steering control.
6. Hook controller on guardrail in original position.
7. On chassis controls, turn key switch to Chassis.
8. From lower controls, push chassis raise button to
elevate platform while pushing the tilt sensor (Fig-
ure 2-3) off of level. The platform should only par-
tially elevate and the tilt alarm should sound. If
the platform continues to elevate and/or there is
no alarm STOP and remove the machine from
service until it is repaired.
9. Release the tilt sensor and fully elevate platform. Figure 2-3: Tilt Sensor
10. Visually inspect the elevating assembly, lift cylin-
der, cables and hoses for damage or erratic oper-
ation. Check for missing or loose parts.

LX13/41 Electric/Bi-Energy Work Platform 2-3

 Section
2.3 M A C H I N E P RE P A R A T I O N &

2.3 OPERATION Raising and Lowering the Platform

Before operating work platform, ensure that the pre- 1. Position the drive/lift switch to LIFT.
operation and safety inspection has been completed, 2. While holding the control lever so the interlock
any deficiencies have been corrected and the opera- lever is depressed, push the control lever slowly
tor has been thoroughly trained on this machine. to UP to raise the platform. Pushing the control
lever farther increases the lift speed.
Travel With Platform Lowered 3. Lower the platform by pulling back on the control
1. Verify chassis emergency stop switch is in the lever until the platform is fully lowered.
ON position (pulled out), the drive enable indica-
tor light is on, and that the platform/chassis Travel with Work Platform Elevated
switch is on PLATFORM. Travel with platform elevated ONLY on firm and level
NOTE: If the drive enable indicator light is off, surfaces.
verify that the platform is fully lowered. NOTE: The work platform will travel at reduced
2. After mounting platform, close and latch gate. speed when in the elevated position, and only
Check that guardrails are in position and properly when the front axle is parallel with the rear
assembled with fasteners properly torqued. axle.
3. Check that route is clear of persons, obstructions, 1. Check that the route is clear of persons, obstruc-
holes and drop-offs and surface is capable of tions, holes and drop-offs, surface is level and
supporting the wheel loads. capable of supporting the wheel loads.
4. Check clearances above, below and to the sides 2. Check clearances above, below and to the sides
of the platform. of platform.
5. Pull controller emergency stop button out to ON 3. Position the drive/lift switch to the DRIVE posi-
position. tion.
6. Set the drive/lift speed range switch to LOW 4. Push the control lever to FORWARD or
SPEED. REVERSE for the desired direction of travel.
7. Grasp the control lever so the interlock lever is If the machine quits driving and the tilt alarm sounds,
depressed (releasing the interlock lever cuts immediately lower the platform and move the
power to controller). Slowly push or pull the con- machine to a level location before re-elevating the
trol lever to forward or REVERSE to travel in the platform.
desired direction. The farther you push or pull the
control lever from center the faster the machine
will travel.
8. While moving, push the drive/lift speed range
switch to HIGH SPEED for travel on level sur-
faces or to LOW SPEED for climbing grades or
traveling in confined areas.
Steering
1. Push the steering switch RIGHT or LEFT to turn
the wheels. Observe the tires while maneuvering
to insure proper direction.
NOTE: Steering is not self-centering. Wheels
must be returned to the straight ahead position
by operating the steering switch.

2-4 LX13/41 Electric/Bi-Energy Work Platform

 Section
M A C H I N E P RE P A R A T I O N & 2.3

Emergency Lowering Parking Brake Release

The emergency lowering knob is located at the front Perform the following only when the machine will not
of the machine at the base of the scissor assembly operate under its own power and it is necessary to
(Figure 2-4). move the machine or when winching onto a trailer to
transport.

! W A R N I N G !
Never release brakes if machine is on a slope.
Hook machine to towing vehicle before releas-
ing brakes.

1. Turn Platform/Chassis/Brake Release switch to

Brake Release position (Figure 2-5). Alarm will
sound.
Emergency 2. Momentarily push brake Release button.
Lowering 3. The machine will now roll when pushed or pulled.
Knob
4. For normal operation, turn Platform/Chassis/
Brake Release switch to Platform position.

Figure 2-4: Emergency Lopwering Knob ! W A R N I N G !

Never operate work platform with the parking
1. Open the emergency lowering valve by pulling on brakes released. Serious injury or damage
the knob and holding it. could result.
2. Once the platform is fully lowered, release the
knob to close the valve.
After Use Each Day
1. Ensure that the platform is fully lowered.
2. Park the machine on level ground, preferably
under cover, secure against vandals, children or
unauthorized operation.
3. Turn the key switch to OFF and remove the key to
prevent unauthorized operation.

Brake
Release

Figure 2-5: Parking Brake Release Button

LX13/41 Electric/Bi-Energy Work Platform 2-5

 Section
2.4 M A C H I N E P RE P A R A T I O N &

2.4 PREPARATION FOR SHIPMENT 2.6 RAISING THE PLATFORM

1. Grease all the grease fittings (see Section 3). From the Platform Controls
2. Fully lower the platform. 1. Select platform at the Chassis/Platform Switch.
3. Uncouple Anderson connectors to disconnect 2. Select lift at the Drive/Lift Switch.
batteries.
3. Push the Control Handle forward.
4. Band the controller to the front guardrail.
a. This will energize;
5. Band the elevating linkage to the frame. • the Drive/Lift Relay
2.5 STORAGE • the Cutout Relay (the Cutout Relay will only
stay energized if the Level Sensor is level
No preparation for storage is required when the work within 2°)
platform is in normal usage. Regular maintenance
• the Up Relay (completing the circuit to the
procedures should continue to be performed (see
Up Solenoid Valve)
Section 3).
• and the Proportional Valve
If the work platform is to be placed in long term stor-
age (dead storage), follow the recommended preser- b. This will allow oil flow;
vation procedures, below. • through the Proportional Valve (regulating
the speed to a rate which is proportional to
PRESERVATION the angle of Control Handle deflection)
1. Clean painted surfaces. If the paint is damaged, • through the Lift Valve
repaint. • through the Down Valve
2. Fill the hydraulic tank to operating level, fluid will • and to the Lift Cylinder (raising the Platform).
be visible at the Sight Gauge. DO NOT fill the
hydraulic tank while the platform is elevated. From the Chassis Controls
NOTE: DO NOT drain the hydraulic system prior 1. Select chassis at the Chassis/Platform Switch,
to long term storage. 2. Press the Up Button
3. Coat exposed portions of extended cylinder rods a. This will energize
with a preservative such as multipurpose grease • the Proportional Valve (regulating speed
and wrap with barrier material. through 10 ohm resistor)
4. Coat all exposed unpainted metal surfaces with • and the Lift Valve.
preservative.
b. This will allow oil flow
BATTERIES • through the Proportional Valve (regulating
the speed to a fixed rate which is set by the
1. Disconnect the batteries negative (-) cables and
10 ohm resistor)
secure to the chassis.
• through the Lift Valve
2. Disconnect the remaining battery leads and
secure to the chassis. • through the Down Valve
3. Remove the batteries and place in alternate ser- • and to the Lift Cylinder (raising the Platform).
vice.

2-6 LX13/41 Electric/Bi-Energy Work Platform

 Section
M A C H I N E P RE P A R A T I O N & 2.7

2.7 LOWERING THE PLATFORM 2.8 DESIGN FEATURES

From the Platform Controls The LX31/41 has the following features to insure safe
operation:
1. Select platform at the Chassis/Platform Switch.
1. The Lift Valve will not energize unless the chassis
2. Pull the Control Handle backward.
is level.
a. This will energize;
2. A warning alarm sounds and Drive Valves are de-
• the Down Relay (completing the circuit to the
energized, if the work platform should become
Down Solenoid Valve)
unlevel while elevated.
• and the Down Alarm Relay (completing the
3. A motion alarm sounds when the work platform is
circuit to the Down Alarm).
lowering.
b. This will sound the down alarm, and allow oil to
4. The platform descent rate is controlled by an ori-
flow;
fice. The Lift Cylinder is equipped with a holding
• out of the Lift Cylinder
valve to prevent descent should a leak develop.
• through the Down Orifice (regulating the
5. The drive speed is limited to “creep” speed when
descent speed)
operating the work platform while elevated.
• through the Down Valve
6. Holding brakes are automatically engaged when
• through the Lift Valve the Drive Valves are de-energized from the Con-
• and out to the Hydraulic Reservoir. troller or from a loss of power.
From the Chassis Controls 7. The Platform and Chassis controls are each
equipped with an Emergency Stop Switch.
1. Select chassis at the Chassis/Platform Switch.
8. Up and Down Buttons are located in the Control
2. Press the Down Button Module on the chassis for lifting and lowering the
a. will energize; work platform from ground level.
• the Down Relay (completing the circuit to the 9. The Down Valve can be operated manually by
Down Solenoid Valve) means of a cable linkage in the event of powered
• and the Down Alarm Relay (completing the function failure.
circuit to the Down Alarm). 10. Dynamic braking, and runaway protection are
b. This will sound the down alarm, and allow oil to provided by the use of Counterbalance Valves in
flow; the drive system.
• out of the Lift Cylinder 11. A Level Sensor is used to sense when the
• through the Down Orifice (regulating the machine is unlevel, disabling lift functions, and
descent speed) drive when elevated.
• through the Down Valve
• through the Lift Valve
• and out to the Hydraulic Reservoir.
Emergency Lowering
The Down Alarm WILL NOT SOUND when lowering
the platform with the Emergency Lowering Knob.
Pull out on the Emergency Lowering Knob to
mechanically open the Down Valve. This will allow oil
to flow;
• out of the Lift Cylinder
• through the Down Orifice (regulating the descent
speed)
• through the Down Valve
• through the Lift Valve
• and out to the Hydraulic Reservoir.

LX13/41 Electric/Bi-Energy Work Platform 2-7

 Section
2.9 M A C H I N E P RE P A R A T I O N &

2.9 CONTROLS AND INDICATORS ure 2-6 correspond to the index numbers in Table 2-
1. The operator shall know the location of each con-
The controls and indicators for operation of the LX trol and indicator and have a thorough knowledge of
31/41 Electric Work Platform are shown in Figure 2- the function and operation of each before attempting
6. The name and function of each control and indica- to operate the unit.
tor are listed in Table 2-1. The index numbers in Fig-

Table 2-1: Controls and Indicators

Controller/Platform Chassis
No. Index Name Function No. Index Name Function

1 Key Switch Turn key fully RUN to provide power to the 9 Emergency Stop Push red button to cut power to all controls
Interlock Switch Switch (off). Turn clockwise to provide power (on).
2 Emergency Stop Push red button to cut power to all controls 10 Raise Button Press button to lift the platform.
Switch (off). Turn clockwise to provide power (on).
3 Control Lever Move joystick forward or backwards to control 11 Lower button Press button to lower the platform.
Drive and Lift Valves proportionally or Down 12 Platform Chassis Turn switch to the left to enable platform
Valve depending on position of Drive Lift Switch controls. Turn switch to the right to enable
Switch. chassis controls.
4 Steering Switch Moving the momentary rocker switch RIGHT or 13 Brake release Press button to release the Parking Brake.
LEFT steers the work platform in that direction. Button
Although the Steering Switch is self centering, 14 Down Alarm* Sounds an audible signal while platform is
the steering system is not. The wheels must lowering during normal operation. If the
be steered back to straight. Emergency Lowering Valve is used, the alarm
does not sound.
5 Drive Speed/ Provides two speed/torque ranges, in forward Tilt Alarm* Sounds an audible signal when the platform is
Torque Selector or reverse. elevated and on a slope of 2° side to side of
Switch HIGH SPEED = Low Torque, and fore and aft.
HIGH TORQUE = Low Speed
6 Drive/Lift Switch Selecting DRIVE allows the work platform to 15 Hour Meter Tracks the number of hours of engine powered
move foward or reverse. Selecting LIFT allows (optional) operation.
the work platform to raise or lower.
7 Interlock Lever Provides power to the Controller powered 16 Brake release Releases the Parking Brake allowing the
Switch functions, only when depressed, preventing Pump machine to be moved in the event power is lost
accidental activation of the Controller. or for winching onto a trailer. See Section 3.
8 Drive Enable Illuminates when drive is enabled, turns off 17 Emergency Pull out to lower the platform in the event of
Indicator when drive is disabled. Lowering Valve powered function failure.
* Down Alarm and Tilt Alarm are the same unit with different inputs.

2-8 LX13/41 Electric/Bi-Energy Work Platform

 Section
M A C H I N E P RE P A R A T I O N & 2.9

4
3

5 16

10

12

10

13
11 14

15
17

Figure 2-6: Controls and Indicators

LX13/41 Electric/Bi-Energy Work Platform 2-9

 Section
2.10 M A C H I N E P RE P A R A T I O N &

2.10 FOLD DOWN GUARDRAILS Erection Procedure

This procedure is only for passing through doorways. 1. Raise side guardrails making sure each is
Guardrails must be returned to proper position before pushed down to secure the guardrail in the verti-
using the machine. Refer to Figure 2-7 (single deck) cal position.
or Figure 2-8 (double Deck). 2. Install bolts, washers and nuts between the side
Single Deck Fold Down Procedure guardrails, tighten securely.
3. Raise rear guardrail assembly, aligning holes and
install bolts, washers and nuts. Tighten securely.
4. Raise front guardrail, aligning holes and install
bolts, washers and nuts. Tighten securely.
5. Hang controller from front guardrail.
6. Before operating work platform check that all fas-
teners are in place and properly torqued.

! W A R N I N G !
Before operating machine, guardrails must be
securely fastened in their proper position.

Figure 2-7: Fold Down Guardrails

NOTE: When performing the following proce-

dures retain all fasteners.
1. Place controller on platform.
2. Starting at the front of the platform, remove nuts,
bolts and washers from the top of the front guard-
rail. Fold the front guardrail down onto the plat-
form.
3. Close and latch the gate.
4. Remove nuts, bolts and washers from the top of
the rear guardrail. Fold the rear guardrail down
onto the platform being careful to keep gate
latched at all times.
5. Remove nuts, bolts and washers from the top of
the side guardrails. Lift up and fold one side
guardrail in so it rests on the deck. Repeat with
other side guardrails.

2-10 LX13/41 Electric/Bi-Energy Work Platform

 Section
M A C H I N E P RE P A R A T I O N & 2.10

Double Deck Fold Down Procedure Erection Procedure

1. Raise front guardrail making sure it is pushed
down to secure the guardrail in the vertical posi-
tion. Repeat for rear guardrail.
2. Raise side guardrails making sure each is
pushed down to secure the guardrail in the verti-
cal position, align holes and install bolts, washers
and nuts. Tighten securely.
3. Raise one of the four slide out deck side guardrail
assemblies, align holes and install bolts, washers
and nuts. Tighten securely. Repeat this proce-
dure for the other three slide out deck side guard-
rails.
4. Hang controller from front guardrail.
5. Before operating work platform check that all fas-
teners are in place and properly torqued.

! W A R N I N G !
Before operating machine, guardrails must be
securely fastened in their proper position.

Figure 2-8: Fold Down Guardrails (Double Deck)

NOTE: When performing the following proce-

dures retain all fasteners.
1. Place controller on platform.
2. Starting at the front slide out deck, remove nuts,
bolts and washers from the top front corners of
guardrails. Remove the nuts, bolts and washers
from the slide out deck side guardrail midrails.
Also remove nuts, bolts and washers located at
the top of the sockets that hold the slide out deck
side guardrails to the deck. Fold the side guard-
rails down onto the platform.
3. Follow step 2 to fold the side guardrails on the
rear slide out deck.
4. Unlatch the gate so the left side guardrails can be
folded down in two separate pieces. Also remove
the nuts, bolts and washers opposite the gate
latch on the right side guardrail so it too can be
separated into two pieces.
5. Lift up and fold side guardrails in so they rest on
the deck.
6. Lift up and fold front guardrail in so it rests on the
deck. Repeat for rear guardrail.

LX13/41 Electric/Bi-Energy Work Platform 2-11

 Section
2.10 M A C H I N E P RE P A R A T I O N &

NOTES

2-12 LX13/41 Electric/Bi-Energy Work Platform

 Section 3
MAINTENANCE

3.1 INTRODUCTION General Procedures

CONTACT BLOCKS: Removed by inserting a flat
screwdriver into the slot at either end of block and
! W A R N I N G ! prying outward. Installed by pressing into an empty
Be sure to read, understand and follow all infor- slot.
mation in the Operation Section of this manual
before attempting to operate or perform service SWITCH MOUNT BASE: Assembled to back of switch
on any Work Platform. actuator. Removed by rotating the small black lever
counterclockwise and lifting off base.
NOTE: For Information on the engine refer to your TERMINAL BLOCKS: Remove wires by inserting a
local engine dealer. small flat bladed screwdriver into square beside wire.
This section contains instructions for the mainte- Install wires by stripping 12 mm (1/2”) of insulation,
nance of the Work Platform. Procedures for the oper- inserting screwdriver in square and inserting wire. Be
ation inspection, adjustment, scheduled sure no strands are bend backwards. Replace wires
maintenance, and repair/removal are included. with same rating and type.
Referring to Section 2 will aid in understanding the 3.2 DATE CODE IDENTIFICATION ON HOSES
operation and function of the various components
and systems of the work platform, and help in diag- GATES uses a five digit code: Year, Month, Day.
nosing and repair of the machine. i.e.: 6 11 29 - means 1996, month 11 (November), day 29.
Refer to “Table 3-1:” on page 3-5 for recommended PARKER uses a ten digit code: Plant, Year, Month, Day.
maintenance intervals. i.e.: XXXX 6 11 29 - means Plant XXXX, 1996, month 11
NOTE: Unless otherwise specified, torque all fit- (November), day 29.
tings according to “Table 3-2:” on
page 3-26, and “Table 3-3:” on page 3-26. DAYCO stamps month, day and year on each hose.

Terminology 3.3 SPECIAL TOOLS

TERMINAL BLOCKS: Located in upper and lower con- The following is a list of special tools which may be
trol boxes. Designated by TB##. (##) designates the required to perform certain maintenance procedures
number of the block which is written on the terminal on the work platform.
block. “R” right or “L” may follow the number. • 0-69 bar (0-1000 psi) Hydraulic Pressure Gauge
WIRE COLOR: Indicated by color/color. First color with Adapter Fittings
refers to insulation color and second color indicates • 0-207 bar (0-3000 psi) Hydraulic Pressure Gauge
stripe. If second color is not given there is no stripe. with Adapter Fittings
FORWARD: Front of machine indicated by yellow • 0-414 bar (0-6000 psi) Hydraulic Pressure Gauge
arrows on chassis. with Adapter Fittings
AFT: Rear of machine indicated by orange arrows on • Small Deutsch Connector Field Kit
machine. (UpRight P/N 030899-000)
• Large Deutsch Connector Field Kit
(UpRight P/N 030898-000)
• Inclinometer

LX31/41 Electric/Bi-Energy Work Platform 3-1

 Section
3.4 MAINTENANCE

3.4 DEUTSCH CONNECTORS

Deutsch connectors are designed so that connector parts, contacts or electrical
cables may be replaced without replacing the entire connector.

Figure 3-1: Deutsch Connector Kit, Small Figure 3-2: Deutsch Connector Kit, Large

Figure 3-3: Plugs and Receptacles, Deutsch Connectors

3-2 LX31/41 Electric/Bi-Energy Work Platform

 Section
MAINTENANCE 3.4

Male Connector (Plug) Crimping

1. Disconnect the male connector (plug) from the NOTE: Complete crimping instructions are
female connector (receptacle). included in each Field Kit.
2. Using the flat end of the Removal Tool (or flat 1. Strip 6 mm (1/4”) from the wire.
blade screwdriver), pry the Locking Wedge from 2. Insert the contact into the crimping tool.
the Male Connector. Care should be taken that
3. Insert the stripped wire into the contact. Copper
the Silicon Gasket is not damaged during this
strands should be visible in the bleed hole of the
procedure.
contact and no copper strands should be loose
3. Check all parts for damage. Replace all parts (outside) of the contact barrel.
which are damaged or worn.
4. Completely close the handles of the crimping
4. Replace or recrimp the wires and contacts. Refer tool. Release the handles of the crimping tool and
to “Crimping” procedure. remove the crimped contact.
Female Connector (Receptacle) 5. Inspect the crimped contact to ensure that all
strands are secure in the crimp barrel.
1. Disconnect the male connector (plug) from the
female connector (receptacle). Removing Contact from
2. Using the notched end of the Removal Tool (or a Heavy Duty Plug
wire hook), pull the Locking Wedge from the
Female Connector.
3. Check all parts for damage. Replace all parts
which are damaged or worn.
4. Replace or recrimp the wires and contacts. Refer
to “Crimping” procedure.
Releasing Locking Fingers

Figure 3-5: Heavy Duty Deutsch Connector

1. Slip the removal tool along the wire to be

replaced.
2. Push the removal tool into the connector until the
contact is released.
3. Pull the wire and contact out of the plug.
Figure 3-4: Locking Finger, Deutsch Connector

1. The Locking Fingers can be released following

the removal of the Locking Wedge of either the
male or female connector.
2. Use the removal tool (or flat bladed screwdriver)
to push the Locking Fingers aside. This will
release the grip on the contact.
3. Pull the wire and contact out of the connector.

LX31/41 Electric/Bi-Energy Work Platform 3-3

 Section
3.5 MAINTENANCE

3.5 PREVENTATIVE MAINTENANCE The preventative maintenance table has been

designed to be used primarily for machine service
The Complete inspection consists of periodic visual and maintenance repair. Please photocopy the fol-
and operational checks, together with all necessary lowing page and use the table as a checklist when
minor adjustments to assure proper performance. inspecting the machine for service.
Daily inspection will prevent abnormal wear and pro-
long the life of all systems. The inspection and main-
tenance schedule is to be performed at regular
intervals. Inspection and maintenance shall be per-
formed by personnel who are trained and familiar
with mechanical and electrical procedures.

! W A R N I N G !
Before performing preventative maintenance,
familiarize yourself with the operation of the
machine.
Always block the elevating assembly whenever
it is necessary to enter the scissor assembly to
perform maintenance while the platform is ele-
vated.

3-4 LX31/41 Electric/Bi-Energy Work Platform

 Section
MAINTENANCE 3.5

Preventative Maintenance Table Key Preventative Maintenance Report

Interval Date: ___________________________________
Owner: _________________________________
Daily=each shift or every day
Model No: _______________________________
50h/30d=every 50 hours or 30 days
Serial No: _______________________________
250h/6m=every 250 hours or 6 months
Serviced By: _____________________________
1000h/2y=every 1000 hours or 2 years
Service Interval: __________________________
Y=Yes/Acceptable N=No/Not Acceptable
R=Repaired/Acceptable

Table 3-1: Preventative Maintenance Checklist

COMPONENT INSPECTION OR SERVICES INTERVAL Y N R COMPONENT INSPECTION OR SERVICES INTERVAL Y N R

Engine Oil Check level and contition Daily Hydraulic Wipe clean 30d
Check for leaks Daily Pump Check for leaks at mating surfaces 30d
Change oi and filter 100h Check for hose fitting leaks Daily
Engine Fuel Check fuel level Daily Check mounting bolts for proper torque 30d
System Check for leaks Daily Drive Motors Check for operation Daily
Replace fuel filter 100h Torque Hubs Check for leaks Daily
Check air filter Daily Check Oil level 250h/6m
Engine Check coolant level (engine cold) Daily Change Oil after break-in 50h/30d
Coolant
Replace coolant 2y Change Oil 1000h/2y
Main Battery Check electrolyte level 6m Steering Check hardware & fittings for proper 6m
Pack Check specific gravity 6m
System torque
Grease pivot pins 30d
Clean exterior 6m
Oil king pins 30d
Check battery cable condition Daily
Check steering cylinder for leaks 30d
Clean terminals 6m
Elevating Inspect for structural cracks Daily
Engine Check electrolyte level 6m Assembly
Battery Check specific gravity 6m
Check pivot points for wear 30d
System
Check mounting pin pivot bolts for proper
Clean exterior 6m torque
30d
Check battery cable condition Daily Check elevating arms for bending 6m
Clean terminals 6m Grease linkage pins 30d
Hydraulic Oil Check oil level Daily Chassis Check hoses for pinch or rubbing points Daily
Change filter 6m Check component mounting for proper
6m
Drain and replace oil 2y torque
Hydraulic Check for leaks Daily Check welds for cracks Daily
System
Check hose connections 30d Lift Cylinder Check the cylinder rod for wear 30d
Check hoses for exterior wear 30d Check mounting pin pivot bolts for proper
30d
torque
Emergency Operate the emergency lowering valve and
Hydraulic check for serviceability Daily Check seals for leaks 30d
System
Inspect pivot points for wear 30d
Controller Check switch operation Daily Check fittings for proper torque 30d
Control Cable Check the exterior of the cable for pinch-
Daily Entire Unit Check for and repair collision damage Daily
ing, binding or wear
Check fasteners for proper torque 3m
Platform Check fasteners for proper torque Daily
Deck and Check welds for cracks Daily
Check for corrosion-remove and repaint 6m
Rails Lubricate 30d
Check condition of deck Daily
Labels Check for peeling, missing, or unreadable
Tires Check for damage Daily Daily
labels & replace
Check lug nuts (torque to 150 ft. lbs. [203
30d
Nm])
Check air pressure (75 psi. [5.2 bar] Daily

LX31/41 Electric/Bi-Energy Work Platform 3-5

 Section
3.6 MAINTENANCE

3.6 BLOCKING ELEVATING ASSEMBLY

! W A R N I N G !
Never perform service on the work platform in
the elevating assembly area while platform is
elevated without first blocking the elevating Upper Scissor
assembly. Center Pivot

DO NOT stand in elevating assembly area while

deploying or storing brace.

Brace Installation
1. Park the work platform on firm level ground.
2. Verify platform emergency stop switch is ON.
3. Turn platform/chassis switch to CHASSIS.
4. Using the raise button, elevate platform until the
scissors brace can be rotated to the vertical posi-
tion.
5. From the left side of the machine, disengage the
locking pin securing the brace. Rotate the scissor
brace counterclockwise until it is vertical and
between the two scissor center pivots. Locking Pin
6. Push lower button and gradually lower platform Lower Scissor
until brace is supporting the platform. Center Pivot

Brace Removal Brace

1. Using chassis controls, gradually raise platform
until the scissors brace clears the two scissor
center pivots.
2. Rotate scissors brace clockwise until the locking
pin engages.
Figure 3-6: Blocking Elevating Assembly
3. Push lower button to completely lower platform.

3-6 LX31/41 Electric/Bi-Energy Work Platform

 Section
MAINTENANCE 3.7

3.7 BATTERY MAINTENANCE Torque Hubs

NOTE: Change oil in torque hubs after the first 50
hours of operation. Change every 2000
! W A R N I N G ! hours thereafter.
Hazard of explosive gas mixture. Keep sparks, 1. Remove Torque Hub from drive assembly (refer
flame, and smoking material away from battery. to “3.16 Torque Hub” on page 3-18).
Always wear safety glasses when working with 2. Remove drain plug from underside of Torque
batteries. Hub.
Battery fluid is highly corrosive. Thoroughly 3. Drain oil from unit.
rinse away any spilled fluid with clean water.
4. Replace drain plug.
Battery Inspection and Cleaning 5. Remove fill plug from top side of torque hub.
6. Remove fill level plug from side of hub.
Check battery fluid level daily, especially if work plat-
form is being used in a warm, dry climate. If required, 7. Fill unit with SAE 90 gear oil until oil comes out fill
add distilled water ONLY. Use of tap water with high level plug opening (1/2 full).
mineral content will shorten battery life. 8. Replace fill level plug. Replace fill plug.
The batteries and cables should be inspected regu-
larly for signs of cracks in the cases, electrolyte leak-
age and corrosion of the terminals. Inspect cables for
worn spots or breaks in the insulation and for broken
cable terminals.
Clean the batteries when it shows signs of corrosion
at the terminals or when electrolyte has overflowed
during charging. Use a baking soda solution to clean
the battery, taking care not to get the solution inside
the cells. Rinse thoroughly with clean water. Clean
batteries and cables contact surfaces to a bright
metal finish whenever a cable is removed.
3.8 LUBRICATION
Refer to Table 3-1 for the lubrication intervals and
Figure 3-7 for location of items that require lubrica-
tion service. Refer to the appropriate sections for
lubrication information on the Steering Linkage,
Torque hubs, and Hydraulic Oil and Filter.
Grease Fittings
Wipe each grease fitting before and after greasing.
Using multipurpose grease in a grease gun, pump
the grease into the fitting until grease just begins to
appear at the edges of the pivot, wipe off any excess
grease.
Steering Linkage
Apply one or two drops of penetrating oil to each
pivot and King Pin bearing

Figure 3-7: Lubrication Chart

LX31/41 Electric/Bi-Energy Work Platform 3-7

 Section
3.8 MAINTENANCE

Hydraulic Oil And Filter

Fluid Level 1
2
With the platform fully lowered, the oil should be visi-
ble in the Sight Gauge. If the oil is NOT visible, fill the
tank until the oil can be seen. DO NOT fill above the
Sight Gauge or when the Platform is elevated.
3
Oil and Filter Replacement
1. To change the filter only, follow Steps 5, 6, and 7.

! C A U T I O N !
The hydraulic oil may be hot enough to cause
burns. Wear safety gloves and safety glasses
when handling hot oil.
4

2. Provide a suitable container to catch the drained 1. Filter Body 3. Sight Gauge
oil. The hydraulic tank has a capacity of 107 liters 2. Breather 4. Drain Plug
(under tank)
(28.3 US gallons).
Figure 3-8: Hydraulic Oil Tank and Filter
3. Remove the drain plug and allow all oil to drain
into the container, be sure to dispose of oil prop-
erly.
4. Reinstall the drain plug.
5. Remove the three screws from the filter body
cover and open the filter body.
6. Lift the filter element from the filter body.
7. Fill the hydraulic oil tank to the level of the sight
gauge with ISO #46 hydraulic oil.
8. Insert the replacement filter element into the filter
body and press into position.
9. Replace the filter body cover and screws.

3-8 LX31/41 Electric/Bi-Energy Work Platform

 Section
MAINTENANCE 3.9

3.9 SETTING HYDRAULIC PRESSURES PRESSURE GUAGE

NOTE: Follow Pump Set - Up procedure when-

ever Pump has been replaced, or when FLOW
testing performance to isolate possible CONTROL
RELIEF VALVE
PUMP FLOWMETER
failure. Refer to Figure 3-10 for flow meter VALVE

set - up.
SIMULATED LOAD
SIMULATED LOAD
SENSELINE

Pump Motor
TANK TANK
Brake Valve
Block Figure 3-11: Flow Meter Setup

Lift Relief Valve

1. Operate the hydraulic system 10 - 15 minutes to
warm the oil.
2. Remove the cap or loosen the locknut on the Lift
Relief Valve.
3. Turn the Lift Relief Valve adjustment screw coun-
terclockwise two full turns.
4. Place rated load on the platform (Refer to specifi-
cations, Section1)
Figure 3-9: Hydraulic Pump
5. Depress the Throttle Button, and the Raise But-
ton to lift the platform.
6. Slowly turn the Lift Relief Valve adjustment screw
2 clockwise until the platform begins to rise.
8
7. Replace the cap, or tighten the locknut on the Lift
Relief Valve, and remove the load from the plat-
form.
Steering Relief Valves
1. Operate the hydraulic system 10 to 15 minutes to
3
warm the oil.
2. Install a 0-207 bar (0-3000 PSI) gauge at the
5 4 Main Pressure Test Port.
7
3. Loosen the locknut or remove the cap on the Left
Steer Relief Valve.
6 4. Turn the adjustment screw two full turns counter-
clockwise.
5. Press the Steering Switch to the left and hold
1. Steering relief valve 5. Lift Relief Valve
2. Flow Control Valve 6. High Pressure Test Port until the system bypasses.
3. Lift Solenoid 7. Steering Solenoids 6. Turn the Steering Relief Valve adjustment screw
4. Dump Solenoid 8. Lift Test Port
clockwise until the gauge reads 103,4 bar (1500
Figure 3-10: Valve Manifold PSI)
7. Tighten locknut or replace cap on Left Steering
Relief Valve.
8. Repeat process for Right Steering Relief Valve.

LX31/41 Electric/Bi-Energy Work Platform 3-9

 Section
3.10 MAINTENANCE

3.10 SWITCH ADJUSTMENTS

Proportional Control Adjustment
Potentiometers are sealed to protect sensitive adjust- Low Range High Range
ments from vibrations, or from tampering. Remove Ramp Threshold
sealant prior to adjustment, and replace after.
NOTE: Do not use silicone sealer; it will damage
pots.
Use a small screwdriver or special adjustment tool to
set adjustment pots. Pots can be easily damaged.
Pots have 15 turns of adjustment, more than one turn
will often be required to complete the adjustment. If
pots have been previously set, reset by turning no
more than 1 turn at a time. If they have not been pre-
viously set, preset to about mid range and start from
there. Figure 3-12: Rotary Control Adjustment, Upper
Control Box
Turn pot clockwise (CW) to increase settings.
Turn pot counterclockwise (CCW) to decrease set-
tings.
Adjust pots only in sequence as outlined in this pro-
cedure.
Proportional Drive Control
IMPORTANT: Back out ramp trimpot 10 turns
(counter clockwise) before making any
adjustments.
Adjusting one pot affects the setting of others. After
making all adjustments recheck each function to ver-
ify settings.
1. Adjust sensitivity threshold pot (located in upper
control box) to obtain an equal threshold between
forward and reverse directions (Figure 3-12).
2. Set Sevcon motor values. Drive adjustments are
made through the motor control calibrator.

3-10 LX31/41 Electric/Bi-Energy Work Platform

 Section
MAINTENANCE 3.10

Platform Down Limit Switches Tilt Sensor

The Platform Down Switches close the circuit to the The Tilt Sensor has three wires; red-power (48v in),
Cutout Relay, bypassing the Tilt Sensor when the black-ground, white-output (48v out). To verify the
platform is lowered; and to the Platform Down Relay, sensor is working properly there is one LED under
which provides power to the Drive Relay, Propor- the sensor; red indicates the sensor is level and the
tional Controller high speed circuit, and Series/Paral- white wire is 'hot' (48v out).
lel Relay.

! W A R N I N G ! Bubble Level

DO NOT attempt to adjust Limit Switches with-

out first blocking the elevating assembly (Refer
to “3.6 Blocking Elevating Assembly” on
page 3-6).

Magnets

Adjustment Nuts

Figure 3-14: Tilt Sensor

Switch Mounting Bracket

1. Check tires for proper pressure.

Capscrews
2. Place machine on firm level surface ± 6 mm (¼°).
Limit Switches 3. Use Inclinometer to ensure that the front and rear
of the Chassis are level within± 6 mm (¼°).
4. Adjust the three leveling locknuts until the bubble
is centered in the circle on the attached bubble
Figure 3-13: Platform Down Limit Switch level.
5. Elevate the platform until the magnetic switches
1. Lower the Platform completely. open (about 3 m [10 feet]) and push the tilt sen-
2. With the Platform / Chassis switch on Chassis, sor base to test the alarm circuit. Alarm should
push the Tilt Sensor base to test the alarm circuit. sound.
3. If the alarm sounds, elevate the Platform and
adjust the position of the switch mounting bracket
by loosening the capscrews and nuts holding the
bracket in place and moving the bracket until the
switches align with the magnets. Lower the Plat-
form and retest. When switches are aligned,
alarm will not sound while platform is lowered.
4. With platform elevated, repeat step 2. When
switches are properly adjusted, alarm will sound.

LX31/41 Electric/Bi-Energy Work Platform 3-11

 Section
3.11 MAINTENANCE

3.11 HYDRAULIC MANIFOLD Assembly

Though it is not necessary to remove the manifold to NOTE: Lubricate all O-rings before installation to
perform all maintenance procedures, a determination prevent damage to O-rings. Seat all balls
should be made prior to beginning as to whether or in manifold block by lightly tapping on the
not the manifold should be removed before mainte- ball with a brass drift punch.
nance procedures begin. 1. Install fittings, plugs, springs, balls and orifices.
Use one drop of Locktite #242 on each screw-in
Removal orifice.
1. Disconnect the battery ground cable. 2. Install solenoid valves, lift relief valve, counter
2. Tag and disconnect the solenoid valve leads from balance valves, divider combiner valve, and spool
the terminal strip. valve.
3. Tag, disconnect and plug hydraulic hoses. 3. Install coils on solenoid valves.
4. Remove the bolts that hold the manifold to the Installation
mounting bracket.
1. Attach manifold assembly to mounting plate with
5. Remove manifold block. bolts.
Disassembly 2. Connect Solenoid leads to terminal strip (as pre-
viously tagged).
NOTE: Mark all components as they are removed
so as not to confuse their location during 3. Connect hydraulic hoses. Be certain to tighten
assembly. Refer to Figure 3-15 often to aid hoses to manifold.
in disassembly and assembly. 4. Operate each hydraulic function and check for
1. Remove coils from solenoid valves. proper operation and leaks.
2. Remove spool valve cover and spool valve. 5. Adjust lift relief, steering relief, and counterbal-
3. Remove solenoid valves, lift relief valve, counter- ance valve pressures according to instructions in
balance valves and divider combiner valve. “3.9 Setting Hydraulic Pressures” on page 3-9.
4. Remove fittings, plugs, springs, balls and orifices.
Cleaning and Inspection
1. Wash the manifold in cleaning solvent to remove
built up contaminants and then blow out all pas-
sages with clean compressed air.
2. Inspect the manifold for cracks, thread damage
and scoring where O-rings seal against internal
and external surfaces.
3. Wash and dry each component and check for
thread damage, torn or cracked O-rings and
proper operation.
4. Replace parts and O-rings found unserviceable.

3-12 LX31/41 Electric/Bi-Energy Work Platform

 Section
MAINTENANCE 3.11

Figure 3-15: Hydraulic Manifold, Exploded View

LX31/41 Electric/Bi-Energy Work Platform 3-13

 Section
3.12 MAINTENANCE

3.12 HYDRAULIC POWER UNIT 3.13 HYDRAULIC BRAKES

NOTE: Brushes on the electric motor can be Removal
replaced without removing the hydraulic
power unit from the chassis by raising and 1. Park the work platform on firm level ground and
securely blocking the chassis and work block the wheels to prevent the work platform
from underneath the chassis. from rolling.
NOTE: Power unit may be removed through the 2. Disconnect the hydraulic brake lines.
front of the chassis by moving the relay 3. Tag and disconnect electric cables from drive
panel out of the way or through the bottom motors.
of the chassis by raising and securely
blocking the chassis. Drain the hydraulic
tank before removing power unit.
! C A U T I O N !
Removal
Clean all fittings before disconnecting the hose
1. Mark, disconnect and plug the hose assemblies. assemblies.
2. Mark and disconnect the electric cables. Plug all port holes and hose assemblies IMME-
3. Remove hardware which secures power unit and DIATELY to prevent contamination from dust
remove from chassis. and debris.
Installation 4. Remove capscrews and washers holding the
1. Install power unit using hardware previously motor and brake to torque hub.
removed. 5. Remove the motor.
2. Unplug and reconnect the hydraulic hoses. 6. Remove the brake.
3. Reconnect the electric cables.
4. Fill the tank with clean hydraulic fluid.
5. Check the oil level in the hydraulic tank before
operating the work platform.
Brake
6. Operate the pump and check for leaks and proper
operation. Drive Motor

7. Replenish hydraulic fluid if necessary.

Pump Motors
Brake Valve
Block

Figure 3-17: Rear Axle Assembly

Figure 3-16: Hydraulic Power Unit

3-14 LX31/41 Electric/Bi-Energy Work Platform

 Section
MAINTENANCE 3.13

Brake Seal Replacement 5. Remove the jack stands and lower chassis to the
ground.
Refer to Figure 3-18.
6. Position chassis switch to parking brake release
1. With shaft protrusion downward remove cap-
position. Alarm will sound.
screws (21) and washers (20) from brake assem-
bly. 7. Depress the electric motor start switch to ener-
gize brake hydraulic system.
2. Remove power plate (19) from housing (1).
Remove the gasket (2). 8. Check for leaks and bleed air out of brake hydrau-
lic system using bleed valve located on brake
3. Remove piston (14) from power plate (19) by
housing.
introducing low pressure air (15 psi) into the
hydraulic inlet. Make sure piston is not pointed at
anyone.
4. Remove o-rings (16 & 18) and backup rings (15 &
17) from inner and outer diameter grooves of pis-
ton.
5. Clean piston (14) and power plate (19) assem-
blies with solvent. Inspect the sealing surfaces of
the piston (14) and power plate (19). Inspect seal
grooves in the piston. Replace brake assembly if
they are damaged or scratched deeply. Lubricate
piston (14), power plate (19), and seals (15, 16,
17, & 18) with clean hydraulic oil prior to assem-
bly.
6. Install the backup rings (15 & 17) and o-rings (16
& 18) into the seal grooves in the piston.
7. Install piston into power plate using a shop press.
Be careful not to damage the seals during
assembly. Center cutouts in piston with torque pin
holes in the power plate. Press piston to a depth
no less than flush, but not exceeding 0.120 in.
below the surface of the power plate at cutouts in
piston. This depth is critical. The brake will not 1. Housing 12. Rotating Disk
hold if it is exceeded. 2. Gasket 13. Stationary Disk
8. Install gasket (2). 3. Ball Bearing 14. Piston
4. Retaining Ring 15. Backup Ring
9. Install power plate/piston assembly (14 & 19) to 5. Oil Seal 16. O-ring
housing (1) using capscrews (21) and washers 6. Spring Retainer 17. Backup Ring
(20). Tighten sequentially, one turn at a time, to 7. Spring, Compression 18. O-ring
8. Shaft 19. Power Plate
press the two assemblies together. Torque cap-
9. Pin, Torque 20. Washer
screws 50 - 60 ft.-lbs. 10. Primary Disk 21. Capscrews
11. Spring, Compression 22. Gaskets
Installation
1. Coat output shafts of brake and drive motor with Seal Kit (068569-000) Includes:
high pressure molybdenum grease and install Item Description Quantity
2 Gasket 1
gasket (22) and brake onto torque hub. 15 Backup Ring 1
2. Install gasket (22) and drive motor. Align holes 16 O-ring 1
17 Backup Ring 1
and install the two cap screws and lock washers. 18 O-ring 1
3. Reinstall cables to drive motor and hoses to the 22 Gaskets 2
brake. Figure 3-18: Brake Assembly
4. Install the wheel. Torque the wheel nuts to 122 N-
m (90 ft. lbs.).

LX31/41 Electric/Bi-Energy Work Platform 3-15

 Section
3.14 MAINTENANCE

3.14 GENERATOR, BI-ENERGY MODELS ONLY

Figure 3-19: Engine, Generator, and Drive Belt Adjustments

Generator
The Bi-Energy work platform is equipped with a die-
sel powered 48 volt, 100 amp generator. There are
no brushes or springs to replace.
Drive Belt Adjustment
1. Open the power module to gain access to the
generator.
2. Loosen the the bolt and nut at both ends of the
adjustment arm.
3. Pry the generator back until the drive belt can be
deflected 2,5 mm (3/32”) with 8 N-m (6 lb/ft) of
force.
4. Tighten the bolts at both ends of the adjustment
arm.
Fuel Tank
The fuel tank is located in the control module on Bi-
Energy models.

1. Fuel Tank 5. Drain Plug

2. Hose Fitting, 3/16 6. Withdrawal Tube
3. Hose Fitting, 1/4 7. Bushing
4. Fuel Cap

Figure 3-20: Fuel Tank, Bi-Energy Models

3-16 LX31/41 Electric/Bi-Energy Work Platform

 Section
MAINTENANCE 3.15

3.15 DRIVE MOTORS Drive Motor Brushes

Removal Refer to Figure 3-21
1. Disconnect battery negative terminals or Ander- 1. If necessary, remove electric motor (Refer to pre-
son connectors (both sides on electric model). vious section).
2. Tag and disconnect electric cables from motor. 2. Release latch and remove headband.
3. Remove and save hardware which secures drive 3. Pull back brush spring and latch on hook.
motor to torque hub. 4. Remove screw and set aside.
Installation IMPORTANT: Be sure screw does not fall inside
NOTE: Unless otherwise specified, torque all fit- motor.
tings according to “Table 3-2:” on 5. Remove old brush and replace with new brush.
page 3-26, and “Table 3-3:” on page 3-26. 6. Replace screw, unhook brush spring and return
1. Install drive motor to torque hub using original to original position.
hardware. 7. Install and relatch headband.
2. Connect electric cables to motor.
3. Connect Anderson connectors or negative termi- Hook
nals on batteries.
Pump Motor
Hook
Removal
1. Disconnect battery negative terminals or Ander-
son connectors (both sides on electric model).
2. Tag and disconnect electric cables from motor.
3. Remove and save hardware which secures pump
motor to pump assembly.
Brush
Installation
NOTE: Unless otherwise specified, torque all fit-
tings according to “Table 3-2:” on Screw
page 3-26, and “Table 3-3:” on page 3-26.
1. Install motor using original hardware.
2. Connect electric cables to motor. Figure 3-21: Replacing Drive Motor Brushes
3. Connect Anderson connectors or negative termi-
nals on batteries.

LX31/41 Electric/Bi-Energy Work Platform 3-17

 Section
3.16 MAINTENANCE

3.16 TORQUE HUB Installation

Removal IMPORTANT: Hub must be installed with 90° fit-
ting in same position as when it was
1. Park the work platform on firm level ground and removed.
block the wheels to prevent the work platform NOTE: Unless otherwise specified, torque all fit-
from rolling. tings according to “Table 3-2:” on
2. Disconnect battery negative terminals or Ander- page 3-26, and “Table 3-3:” on page 3-26.
son connectors (both sides on electric model). 1. Install torque hub using 1/2-20 nuts and 1/2
3. Loosen the wheel lug nuts on the torque hub to washers.
be removed. 2. Remove plug from 90° fitting and install fitting in
4. Raise the rear of the work platform using a 2-ton side of torque hub. Point fitting towards rear of
jack. hub.
5. Position two 2-ton jack stands under the rear axle 3. Using 90 weight gear lube with EP additive, fill
to prevent the work platform from falling if the jack torque hub through top plug hole in rear cover
fails. until oil comes out of 90° fitting in side. Plug 90°
6. Remove the wheel nuts and wheel. fitting and top of rear cover.
7. Disconnect hydraulic brake line from brake. 4. Install new gasket and brake.
5. Install new gasket and electric motor.
6. Secure assembly using washers and bolts.
! C A U T I O N ! 7. Connect hydraulic brake lines.
Clean all fittings before disconnecting the hose 8. Connect electric cables.
assemblies. 9. Install wheels. Torque lug nuts to 123 Nm (90 ft.
Plug all port holes and hose assemblies IMME- lbs.).
DIATELY to prevent contamination from dust 10. Bleed brake lines if necessary.
and debris.
11. Remove jack stands and lower rear end.
8. Remove 90° fitting from side of torque hub. 12. Connect battery terminals or Anderson connec-
tors.
9. Tag and remove electric cables from drive
motors. 13. Check function of brake.
10. Remove mounting bolts from electric motor.
11. Separate electric motor from brake. Discard gas-
ket.
12. Separate brake from torque hub. Discard gasket.
13. Remove 1/2-20 nuts and washers from torque
hub.
14. Remove torque hub.
IMPORTANT: Note position of 90° fitting on
torque hub body. Hub must be installed
with fitting in same position.

1. Motor 4. Torque Hub

2. Gasket 5. 90° Fitting
3. Brake

Figure 3-22: Torque Hub Assembly

3-18 LX31/41 Electric/Bi-Energy Work Platform

 Section
MAINTENANCE 3.17

3.17 TORQUE HUB SEAL REPLACEMENT Disassembly

Roll And Leak Testing CAUTION: Safety glasses should be used during
disassembly of hub.
IMPORTANT: Torque hubs should always be roll
and leak tested before disassembly and 1. Remove two pipe plugs in cover and drain the oil
after assembly to make sure gears and from the unit.
sealants are working properly. 2. Loosen and remove shoulder bolts and cap
screws from cover. Remove cover from hub.
Roll Test
3. Remove O-ring. Remove thrust washer from
Gears should be able to rotate by applying a constant counterbore in cover.
force to the axle. Some gear packages roll with more
difficulty than others. 4. Remove input gear from planet gears.
Do not be concerned if gears seem to roll hard as 5. Using a punch, remove retaining ring from groove
long as they roll with consistency. If you feel more around inside of input gear.
drag only at certain points the gears are not rolling 6. Lift carrier sub-assembly from hub. Lift ring gear
freely and should be checked for improper installation from hub. Remove O-ring from counterbore in
or defects. hub.
7. Remove pipe plugs from side of hub body.
Leak Test
8. Apply a preload to output shaft to remove retain-
The purpose of a leak test is to make sure the unit is ing ring. Follow steps a & b.
air tight. Pressurize hub to 0,34 bar (5 PSI). Torque
hub has a leak if the air pressure starts to fall after a. Place bearing cone pressing tool on retaining
hub has been pressurized. ring.
Use soap and water on hub to detect location of b. Apply pressure to fixture using a hydraulic ram
leaks. If a leak is detected, seal or O-ring must be or by striking the fixture with a soft face ham-
replaced. mer. Pressure should be applied until hub
rotates with difficulty.
Pressing Tools 9. Using retaining ring pliers remove retaining ring.
Use pressing tools to remove the seal, cup and cone. Remove spacer from output shaft.
10. Place spacer under hub so output shaft will fall
through bottom when pressed out.
11. Press output shaft out of hub. Output shaft may
come out with bearing cone and seal attached.
Remove seal and discard. Use a punch and ham-
mer to remove bearing cone. Be careful not to
strike shaft with punch.
12. If seal and cone remain in hub, press them out
using a pressing tool.
13. Lift bearing cone out of hub.
14. Stand hub on its small end. Using a punch and
hammer, remove bearing cup from counterbore
of hub. Be careful not to strike counterbore with
punch.
15. Turn hub over on larger end. Using a punch and
hammer, remove bearing cup from counterbore
of hub. Be careful not to strike counterbore.
NOTE: Carrier sub-assembly does not need to be
disassembled to replace seals.

LX31/41 Electric/Bi-Energy Work Platform 3-19

 Section
3.17 MAINTENANCE

Assembly d. Remove spacer and replace it with thicker

spacer (SK91 068570-011).
NOTE: Unless otherwise specified, torque all fit-
tings according to “Table 3-2:” on e. Repeat steps 6-9 and remeasure end play (Fig-
page 3-26, and “Table 3-3:” on page 3-26. ure 3-23).
1. Oil output shaft and bearing cone. Using cone 10. Apply a light coat of "Never Seize" to the pipe
press, press bearing cone onto end of output plugs and install into pipe plug holes in hub.
shaft with retaining ring groove. NOTE: Leave hole for 90° fitting open.
2. Stand hub on its small end. Using bearing cup
pressing tool press bearing cup down into hub.
NOTE: Make sure cup sits square with counter-
bore.
3. Turn hub over so it sit on large end. Using bearing
cup pressing tool press bearing cup into small
end of hub.
NOTE: Make sure cup sits square with counter-
bore.
4. Place output shaft into hub so end of shaft with
retaining ring groove points down.
5. Oil output shaft. Using seal pressing tool press
seal into counterbore in small end of hub. The
closed face of the seal should be up.
6. Turn hub over so small end points down. Using Figure 3-23: Measuring Hub End Play
bearing cone pressing tool, press bearing cone
onto output shaft. Rotate hub while pressing
bearing. Stop pressing when hub starts to resist
rotating.
7. Place spacer onto output shaft so it rests on top
of bearing cone. Using retaining ring pliers, place
retaining ring to make sure it is seated.
8. Hit the end of output shaft once or twice with a
soft face hammer. Turn the shaft in both clock-
wise and counter clockwise directions while hit-
ting. This will seat the bearing cone against the
spacer and retaining ring allowing necessary
endplay in the hub-shaft sub-assembly.
9. Turn hub over so it rests on large end. Measure
endplay in hub-shaft sub-assembly. Follow steps
a-c.
a. Mount a dial indicator on hub. Locate the dial
rod on top of output shaft.
b. Lift up on output shaft until the needle on the
dial stops moving.
c. Read the dial. Reading should be no greater
than 0,203 mm (.008 in).
- If dial reads less than 0,203 mm (.008 in),
continue on to step 10.
- If dial reads more than .0,203 mm (.008 in),
repeat steps 8-15 of "DISASSEMBLY" section.

3-20 LX31/41 Electric/Bi-Energy Work Platform

 Section
MAINTENANCE 3.17

Main Assembly
1. Position hub on its output shaft so that hubs small
diameter end points down.
2. Using a marker, mark the four shoulder bolt holes
in hub.
3. Grease O-ring and place in counterbore in hub.
NOTE: O-rings may be stretched or squeezed
together in order to fit exactly in counter-
bore.
4. Oil all exposed surfaces inside hub. Oil carrier
sub-assembly.
5. Place carrier sub-assembly, with spline connec-
tions down, into mesh with output shaft.
6. Place ring gear, with squared shoulder down, into
mesh with the planet gears of the carrier sub-
assembly. Make sure that marked shoulder bolt
hole on ring gear aligns with any of the marked
shoulder bolt holes on the hub. "X" mark should
be on the cover side of ring gear.
7. Start one half of retaining ring into groove inside
input gear. Use a soft punch to press the remain-
ing half of the retaining ring into the groove.
8. Insert input gear, with large diameter end down,
into mesh with planet gears.
9. Place large thrust washer over input gear so it
rests on carrier housing. Oil all exposed surfaces
inside hub.
10. Grease O-ring and place into counterbore of
cover.
NOTE: O-rings may be stretched or squeezed
together in order to fit exactly in counter-
bore.
11. Place cover on top of ring gear so the fill hole will
be at top of hub when it is installed.
12. Install four shoulder bolts into shoulder bolt holes
and tighten.
13. Install eight cap screws in remaining holes and
tighten.
14. Apply 31-37 N-m (23-27 ft. lbs) of torque to all
bolts.
15. Apply a light coat of "Never Seize" to both pipe
plugs and install into the two holes in cover.
16. Roll test the unit in both clockwise and counter-
clockwise directions. Turn hub nine full revolu-
tions in each direction.
17. Leak test the hub at 0,34 bar (5 PSI) for two to
three minutes.

LX31/41 Electric/Bi-Energy Work Platform 3-21

 Section
3.17 MAINTENANCE

A. Spindle F. sun Gear K. Stud Repair Kit (068570-010) contains:

B. Housing G. Gear, Internal L. Stud
C. Carrier Assembly H. Cover M. Pipe Plug 1. Lip Seal 6. O-ring (2)
D. Gear ring I. Shoulder Bolt N. Pipe Plug 2. Bearing, Cone 7. Washer (2)
E. Spaces, Input J. Bolt 3. Bearing, Cup 8. Thrust Washer - SK91 (068570-011)
4. Thrust Washer 9. Bearing, Cup
5. Retaining Ring 10. Bearing, Cone

Figure 3-24: Torque Hub

3-22 LX31/41 Electric/Bi-Energy Work Platform

 Section
MAINTENANCE 3.18

3.18 CYLINDER REPAIR Assembly

Removal NOTE: Unless otherwise specified, torque all fit-
tings according to “Table 3-2:” on
1. Remove cylinder from machine. page 3-26, and “Table 3-3:” on page 3-26.
NOTE: Refer to “Illustrated Parts Section” for 1. Lubricate all components with clean hydraulic
location of cylinder and list of parts which fluid.
secure cylinder.
NOTE: To avoid cutting the seals, do not use
NOTE: If necessary, refer to “3.6 Blocking Elevat- sharp edged tools during seal replace-
ing Assembly” on page 3-6. ment. After installing seals allow at least
2. Mark and disconnect hoses and IMMEDIATELY one hour for the seals to elastically
cap the openings to prevent contamination. restore to their original shape before
assembling cylinder.
2. Install new seal kit components.
! W A R N I N G ! 3. Lubricate rod wiper and seal with hydraulic fluid
Cylinders may be very heavy. Support heavy and slide head onto rod.
cylinders before removing pins which secure 4. Lubricate seals on piston and head.
cylinder to machine.
5. Carefully slide rod assembly into cylinder.
6. Secure head into cylinder.
Disassembly
1. Remove head from cylinder body. Installation
2. Carefully slide rod assembly out of cylinder. 1. Installation is reverse of removal.
3. remove seal kit components (wipers, rod seals, 2. Carefully remove elevating assembly support.
o-rings and backup rings) from head and piston. 3. Slowly cycle cylinder several times to remove air
4. Inspect parts for scratches, pits or polishing. from the hydraulic system.
Check seal grooves and sealing surfaces. Check for proper cylinder operation. Check hydraulic
Scratches or pits deep enough to catch the finger- connections for leaks.
nail are unacceptable; replace the cylinder. Pol-
ishing is a sign of uneven loading. when this
occurs, the surface should be checked for round-
ness. Cylinders not round within 0,18 mm (.007”)
should be replaced.

LX31/41 Electric/Bi-Energy Work Platform 3-23

 Section
3.19 MAINTENANCE

3.19 STEERING CYLINDER Installation

Removal 1. Align the ends of the cylinder with the mounts on
the chassis.
1. Remove and cap the hoses. Mark them for refer-
2. Install the clevis pins.
ence.
3. Install the hair pin retainers into the clevis pins at
2. Remove the hair pin retainers from the clevis pins
each end of the cylinder.
at each end of the cylinder.
4. Install the hoses, noting their orientation mark-
3. Remove the clevis pins.
ings from disassembly.
4. Remove the cylinder from the chassis.

1. Rod Wiper 8. Locknut

2. Rod Seal 9. O-ring
3. Wear Ring, 2 required 10. Rod Weldment
4. Retaining Ring 11. Tube Weldment
5. Head 12. Piston Seal
6. Backup Ring 13. Piston
7. O-ring 14. Wear Ring Seal Kit Number: 067633-010

Figure 3-25: Steering Cylinder Cross Section

3-24 LX31/41 Electric/Bi-Energy Work Platform

 Section
MAINTENANCE 3.20

3.20 LIFT CYLINDER Installation

Removal NOTE: Before installing the cylinder, check the
pins and bearings for excessive wear.
1. Raise and block the elevating assembly (see “3.6 Replace if necessary.
Blocking Elevating Assembly” on page 3-6). 1. Using a suitable lifting device, lower the cylinder
2. Open emergency lowering valve to be sure all into the elevating assembly from the front. DO
pressure is out of the lift cylinder. NOT sling the cylinder by the rod end pivot, this
3. Remove and cap both hoses and fittings. will cause the cylinder to extend when hoisted.
4. Remove the down valve and cable assembly. 2. Align the pivots and install the pivot pins, lower
5. Support the lift cylinder with a suitable lifting one first, then the upper one.
device to prevent falling. 3. Install the retaining bolts into the pivot pins.
6. Remove the retaining bolts from the upper and 4. Install the down valve and cable assembly. Adjust
lower pivot pins. the cable to stop on the collar of the cable jacket,
7. Drive out the pivot pins, upper one first, then the before the down valve reaches the full extent of
lower one. it's pull. The down valve may leak if the cable is
allowed to pull the spool of the valve beyond it's
8. Hoist the cylinder out of the elevating assembly limit.
from the front. DO NOT sling the cylinder by the
rod end pivot, this will cause the cylinder to 5. Install the hoses.
extend when hoisted. 6. Lift and lower the machine for several cycles to
9. Inspect the rod, head, piston, and tube for work out the air. Check for leaks, repair as neces-
scratches, pits, or polishing. Check seal groves sary.
and sealing surfaces. Scratches or pits deep
enough to catch the fingernail are unacceptable,

1. Rod Wiper 10. Spacer

2. Rod Seal 11. O-ring
3. Wear Ring, 3 required 12. Locknut
4. O-ring 13. Bushing
5. Head 14. Orifice
6. Backup Ring 15. Cast Iron Ring
7. O-ring 16. Wear Ring, 2 required
8. Rod Weldment 17. Piston
9. Tube Weldment 18. Piston Seal
Seal Kit Number: 067635-010

Figure 3-26: Lift Cylinder Cross Section

LX31/41 Electric/Bi-Energy Work Platform 3-25

 Section
3.21 MAINTENANCE

3.21 TORQUE SPECIFICATIONS

Fasteners Hydraulic Components
Use the following values to torque fasteners used on Use the following values to torque hydraulic compo-
UpRight Work Platforms unless a specific torque nents used on UpRight Work Platforms.
value is called out for the part being installed. NOTE: Always lubricate threads with clean
hydraulic oil prior to installation

Table 3-2: Torque Specifications for Fasteners

AMERICAN STANDARD CAP SCREWS METRIC CAP SCREWS

METRIC
SAE GRADE 5 8 8.8 10.9
GRADE

8.8 10.9
Cap Screw
Cap Screw
TORQUE TORQUE Size TORQUE TORQUE
Size (inches)
(millimeters)
Ft./Lbs Nm. Ft./Lbs. Nm. Ft./Lbs. Nm. Ft./Lbs. Nm.
MIN MAX MIN MAX MIN MAX MIN MAx MIN MAX MIN MAX MIN MAX MIN MAX
1/4 - 20 6.25 7.25 8.5 10 8.25 9.5 11 13 M6 x 1.00 6 8 8 11 9 11 12 15
1/4 - 28 8 9 11 12 10.5 12 14 16 M8 x 1.25 16 20 21.5 27 23 27 31 36.5
5/16 - 18 14 15 19 20 18.5 20 25 27 M10 x 1.50 29 35 39 47 42 52 57 70
5/16 - 24 17.5 19 23 26 23 25 31 34 M12 x 1.75 52 62 70 84 75 91 102 123
3/8 - 16 26 28 35 38 35 37 47.5 50 M14 x 2.00 85 103 115 139 120 146 163 198
3/8 - 24 31 34 42 46 41 45 55.5 61 M16 x 2.50 130 158 176 214 176 216 238 293
7/16 - 14 41 45 55.5 61 55 60 74.5 81 M18 x 2.50 172 210 233 284 240 294 325 398
7/16 - 20 51 55 69 74.5 68 75 92 102 M20 x 2.50 247 301 335 408 343 426 465 577
1/2 - 13 65 72 88 97.5 86 96 116 130 M22 x 2.50 332 404 450 547 472 576 639 780
1/2 - 20 76 84 103 114 102 112 138 152 M24 x 3.00 423 517 573 700 599 732 812 992
9/16 - 12 95 105 129 142 127 140 172 190 M27 x 3.00 637 779 863 1055 898 1098 1217 1488
9/16 - 18 111 123 150 167 148 164 200 222 M30 x 3.00 872 1066 1181 1444 1224 1496 1658 2027
5/8 - 11 126 139 171 188 168 185 228 251
5/8 - 18 152 168 206 228 203 224 275 304
3/4 - 10 238 262 322 355 318 350 431 474
3/4 - 16 274 302 371 409 365 402 495 544 NOTE: These values apply to fasteners as received from the supplier, dry or when
lubricated with normal engine oil. They do not apply if special graphited or
7/8 - 9 350 386 474 523 466 515 631 698 molydisulphide greases or other extreme pressure lubricants are used
7/8 - 14 407 448 551 607 543 597 736 809
1-8 537 592 728 802 716 790 970 1070
1 - 14 670 740 908 1003 894 987 1211 1337

Table 3-3: Torque Specifications for Hydraulic Components

Type: SAE Part Series Cartridge Poppet Fittings Hoses

Ft/Lbs Nm Ft/Lbs Nm Ft/Lbs Nm

#4 N/A N/A N/A N/A 135-145 15-16
#6 N/A N/A 10-20 14-27 215-245 24-28
#8 25-30 34-41 25-30 34-41 430-470 49-53
#10 35-40 47-54 35-40 47-54 680-750 77-85
#12 85-90 115-122 85-90 115-122 950-1050 107-119
#16 130-140 176-190 130-140 176-190 1300-1368 147-155

3-26 LX31/41 Electric/Bi-Energy Work Platform

 Section 4
TRO U B L E S H O O T I N G

4.1 INTRODUCTION General Procedure

This section on troubleshooting provides guidelines Use the charts on the following pages to help deter-
on the types of problems users may encounter in the mine the cause of a fault in your UpRight AB46.
field, helps determine the cause of problems, and 1. Verify your problem.
suggests proper corrective action. a. Do a full function test from both platform con-
Careful inspection and accurate analysis of the trols and chassis controls and note all functions
symptoms listed in the Troubleshooting Guide will that are not operating correctly.
localize the trouble more quickly than any other 2. Narrow the possible causes of the malfunction.
method. This manual cannot cover all possible prob-
a. Use the troubleshooting guide to determine
lems that may occur. If a specific problem is not cov-
which components are common to all circuits
ered in this manual, call our toll free number for
that are not functioning correctly.
service assistance.
3. Identify the problem component.
Referring to Section 2.0 and 5.0 will aid in under-
standing the operation and function of the various a. Test components that are common to all cir-
components and systems of the AB46 and help in cuits that are not functioning correctly. Remem-
diagnosing and repair of the machine. ber to check wires and terminals between
suspect components. Be sure to check con-
nections to battery negative.
! W A R N I N G ! 4. Repair or replace component found to be faulty.
When troubleshooting, ensure that the work 5. Verify that repair is complete.
platform is resting on a firm, level surface. a. Do a full function test from both platform and
When performing any service which requires chassis controls to verify that all functions are
the Platform to be raised, ensure that all four (4) operating correctly and machine is performing
outriggers are properly installed. to specified values.
Unplug the machine or disconnect the battery
when replacing or testing the continuity of any UPRIGHT USA TEL: 1-559-891-5200
electrical component. FAX: 1-559-896-9244
UPRIGHT IRELAND TEL: 353-1-202-4100
FAX: 353-1-202-4105

LX31/41 Electric/Bi-Energy Work Platform 4-1

 Section
4.2 TRO U B L E S H O O T I N G

4.2 TROUBLESHOOTING ELECTRICAL SCHEMATICS

Table 4-1: Trouble Shooting Guide: Electrical Schematics

GENERATOR (BI-ENERGY)
ENGINE (BI-ENERGY)
BATTERY CHARGER
LOWER CONTROLS

LOWER PLATFORM
UPPER CONTROLS

HIGH/LOW SPEED
RAISE PLATFORM
DRIVE FORWARD

DRIVE REVERSE

DOWN ALARM
STEER RIGHT

STEER LEFT

TILT ALARM
FUNCTION

BRAKES
COMPONENT
Tilt Alarm ALM1 X
Down Alarm ALM2 X
Battery BAT1 X X X
(Bi-Energy) Battery BAT2 X X
Battery Charger CH1 X
Main Power Contactor C1 X X X X
Forward Contactor C2 X
Reverse Contactor C3 X
Pump Override Contactor C4 X X X X X
Pump/Traction Contactor C5 X X
Controller CONT X X X X X X X X X X
Main Fuse F1 X X X
Main Fuse F2 X X X
Circuit Breaker CB1 X X
Circuit Breaker CB2 X X
(Bi-Energy) Circuit Breaker CB3 X X
Tilt Alarm Diode D1 X X X
Lift Diode D2 X X X
Down Diode D3 X X X X
Down Alarm Diode D4 X
Steer Right Diode D5 X
Steer Left Diode D6 X
Pump Start Diode D7 X X
Brake Relay Diode D8 X X X
Brake Solenoid Diode D9 X X X
Drive/Lift Diode D10 X X X
Brake Release Relay Diode D11 X X X
Down Solenoid Diode D12 X
Diode D13 X
Main Power Diode D14 X X
Diode D15 X X X
Diode D16 X
Pump Override Diode D17 X X X X X
Diode D18 X X X
Diode D19 X X X
Diode D20 X X X
Diode D22 X X X
Power Relay Diode D23 X
Power Relay Diode D24 X
Brake Release Solenoid Diode D25 X X X
Diode D26 X
Diode D27 X
Tilt Alarm Diode D28 X
Up Solenoid Diode D29 X
Up Solenoid Diode D30 X
Diode D31 X X X
Steer Left Solenoid Diode D32 X
Steer Right Solenoid Diode D33 X
Down Alarm Diode D34 X

4-2 LX31/41 Electric/Bi-Energy Work Platform

 Section
TRO U B L E S H O O T I N G 4.2
Table 4-1: Trouble Shooting Guide: Electrical Schematics (Continued)

GENERATOR (BI-ENERGY)
ENGINE (BI-ENERGY)
BATTERY CHARGER
LOWER CONTROLS

LOWER PLATFORM
UPPER CONTROLS

HIGH/LOW SPEED
RAISE PLATFORM
DRIVE FORWARD

DRIVE REVERSE

DOWN ALARM
STEER RIGHT

STEER LEFT

TILT ALARM
FUNCTION

BRAKES
COMPONENT
Main Fuse F1
Main Fuse F2
(Bi-Energy) Engine Fuse F9
(Bi-Energy) Generator GEN
Drive Enable Light L1
Hour Meter M1
Power Unit Motor MOT1 X X X X X X X
Power Unit Motor MOT2 X X X X X X X
Left Traction Motor MOT3 X X X
Right Traction Motor MOT4 X X X
(Bi-Energy) Fuel Pump P1
Drive/Lift Relay R1 X X X X X
8 Meter Cutout Relay R2
Tilt Alarm Relay R3 X
Up Relay R4 X
Down Relay R5 X X X X
Down Alarm Relay R6 X
Steer Right Relay R7 X
Steer Left Relay R8 X
Pump Start Relay R9 X X
Brake Relay R10 X X X
Brake Release Relay R11 X X X
Power Relay R12 X X X X
(Bi-Energy) Start Relay R13
(Bi-Energy) Charge Relay R14
Brake Release Relay R15 X
Platform Power Relay R16 X X X X X
Prevent Pump Start Relay R17
(Bi-Energy) Starter Relay R18
(Bi-Energy) Glow Plug Relay R19
(Bi-Energy) Oil Pressure Relay R20
Resistor Pack RES1 X X X X
Drive Enable Light Resistor RES2
Joystck Interlock Switch S1 X X X X X
Reverse Micro Switch S2 X
Forward Micro Switch S3 X
Lower Emergency Stop Switch S4 X X X X X X
Lift Switch S5 X X
Brake Release Switch S6 X X X
Drive Switch S7 X X
Lift Switch S8 X X X
High/Low Switch S9 X
Platform Down Switches S10-S13 X X X
8 Meter Cutout Switch S14
Up Limit Switch S15 X X X
Pump Start Switch S16 X X X X X
Chassis/Platform Switch S17 X X
Upper Emergency Stop Switch S18 X X X X X X
Steering Micro Switch S19 X X
Proportional Speed Control Switch S20
Ignition Keyswitch S21 X

LX31/41 Electric/Bi-Energy Work Platform 4-3

 Section
4.2 TRO U B L E S H O O T I N G

Table 4-1: Trouble Shooting Guide: Electrical Schematics (Continued)

GENERATOR (BI-ENERGY)
ENGINE (BI-ENERGY)
BATTERY CHARGER
LOWER CONTROLS

LOWER PLATFORM
UPPER CONTROLS

HIGH/LOW SPEED
RAISE PLATFORM
DRIVE FORWARD

DRIVE REVERSE

DOWN ALARM
STEER RIGHT

STEER LEFT

TILT ALARM
FUNCTION

BRAKES
COMPONENT
(Bi-Energy) Start Switch S22
(Bi-Energy) Oil Pressure Switch S23
(Bi-Energy) Glow Plug Switch S24
(Bi-Energy) Engine Run Switch S25
(Bi-Energy) Charge Switch S26
(Bi-Energy) Starter Switch S27
(Bi-Energy) Glow Plug Switch S28
Tilt Sensor SEN1 X X X X X
Up Solenoids SOL1-SOL2 X
Down Solenoid SOL3 X
Steer Right Solenoid SOL5 X
Steer Left Solenoid SOL6 X
Brake Solenoid SOL8 X X X
Forward Solenoid SOL9 X
Reverse Solenoid SOL10 X
Brake Release Solenoid SOL11 X X X
(Bi-Energy) Stop/Run Solenoid SOL12
Tachometer-Generator TG1 & TG2

4-4 LX31/41 Electric/Bi-Energy Work Platform

 Section
TRO U B L E S H O O T I N G 4.3

4.3 TROUBLESHOOTING HYDRAULIC

Table 1: Troubleshooting Guide: Hydraulic Schematics

LOWER PLATFORM
RAISE PLATFORM

RIGHT BRAKE
STEER RIGHT

LEFT BRAKE
STEER LEFT
FUNCTION
COMPONENT

Accumulator ACC X X
Check Valve CV1 X X
Check Valve CV2 X
Left Brake Cylinder CYL1 X
Right Brake Cylinder CYL2 X
Lift Cylinder CYL3 X
Steering Cylinder CYL4 X X
Return Filter F1 X X X X X X
Suction Strainer F2 X X X X X X
Flow Divider FD1 X X
Brake Orifice ORF2 X X
Lift Orifice ORF3 X X
Hydraulic Pump P1 X X X X X X
Hydraulic Pump P2 X X X X X X
Main Relief Valve RV1 X X X X
Steering Relief Valve RV2 X X
Pressure Switch S1 X X
Brake Apply Valve V1 X X
Brake Release Valve V2 X X
Steering Valve V3 X X
Lift Valve V4 X
Dump Valve V5 X X
Down Valve V6 X X

LX31/41 Electric/Bi-Energy Work Platform 4-5

 Section
4.4 TRO U B L E S H O O T I N G

4.4 TROUBLESHOOTING THE MOS90 4.5 USING THE CALIBRATOR

Important basics applicable to the motor control unit. The calibrator has 20 L.E.D. segments marked as
• The MOS90 has a green diagnostics L.E.D. in the shown.
front panel.
• The green L.E.D. will turn on and shine continu-
ously when the MOS90 is powered up and work-
ing correctly.
• The green L.E.D. will be off if no power is sup-
plied to the MOS90.
• The green L.E.D. will flash a sequence of flashes
if the MOS90 is damaged or is receiving an
improper signal. An explanation of the flash
sequences "flash faults" is shown on the following
pages.
• The MOS90 is high temperature protected by
"thermal cutback". The cutback operates
between 80°C (176°F) and 90°C (194°F). Pow-
ered functions will gradually operate slower and
slower until 90°C (194°F). The MOS90 will shut
down at 90°C (194°F). Continued operation at
high temperature will damage the MOS90.
• The MOS90 is low voltage protected by "low volt-
age cutout". The MOS90 shuts down at 14.0
VDC. Powered functions suddenly stop. When
input voltage goes above 14.0 VDC turns back
on.

When a Flash Error occurs

Step 1.
Disconnect the 17 pin connector from the MOS90. Figure 4-1: MOS90 Calibrator LED Segments
Wait Five (5) seconds and plug it back in again. If the The values which should be expected when checking
flash error repeats go to step Two (2). If the green the machine are shown on the following page.
L.E.D. lights up and stays on continuously - operate There are three buttons on the calibrator:
machine. Note which functions are being used when
problem repeats itself.
increment, marked +
decrement, marked -
Step 2. select
Disconnect the 17 pin connector from the MOS90. When select is pressed, each L.E.D. will light in
Connect pin Six (6) to a fused battery supply (14.0 sequence until the select button is released. Each
VDC minimum) and observe the green L.E.D. If flash setting can be incremented or decremented using the
error stays, replace MOS90. If green L.E.D. lights up + or - buttons when the adjacent L.E.D. is lit.
and remains on continuously, check wiring.
When "Test" L.E.D. is lit, the state of the MOS90
NOTE: Troubleshoot the possible cause of the inputs is displayed. The first input displayed is the
flash error before replacing the MOS90, for accelerator which can vary from 0-100%. When the +
example an Eight (8) flash error will cure button is pressed once the switch Input 1 is dis-
itself when the MOS90 cools down.
played. This will be seen as "1.0P" until the switch
Input voltage changes. "1.CL" will then be displayed.
This is repeated for all the switch inputs.

4-6 LX31/41 Electric/Bi-Energy Work Platform

 Section
TRO U B L E S H O O T I N G 4.6
When BATTV, MOTORV, MOTORA and TEMPC are 4.7 UPRIGHT TRACTION CONTROLLER
selected, the controller shows their values. When DISPLAY
BATTV is selected and the "+" button is held in, the
highest voltage that the MOS90 has recorded will be Table 4-3: Calibrator Display
displayed. When TEMPC is selected and the "+" but-
Sequence No. Test Display Input #
ton is held in, the highest temperature that the
- Acc. Input 0-100% 14
MOS90 has recorded will be displayed. The "-" button
1 Forward CL/OP 8
will display the lowest values.
2 Reverse CL/OP 11
When the MOS90 is first powered up, the recorded 3 Tach Input 0-100% 12
minutes of run time is displayed. The "+" button dis- 4 Elev. Pos. CL=Clpsd. 4
plays thousands of hours and the "-" button displays OP=Lifted
hundreds of hours. When the MOS90 is pulsing 5 Tilt Switch CL=Level 7
(being used) run time is being incremented and OP=Tilt
stored. The "dot" in the time display is blinking when 6 Pump Switch CL= Pump 16
MOS90 is being used, steady when idle. OP=Trac.
7 Act. Direction OP=FWD 2
4.6 CALIBRATOR SETTINGS Tacho Output CL=REV
8 High/Low Speed CL=High 13
Table 4-2: Calibrator Settings
OP=Low
LED Function Unit Setting Comments 9 Direction Flag OP=No Dr. -
1 MOS90 Maximum Amp. Capacity Amps 600 Adjustable from 50 CL=Drv actv.
amps to 600 amps 10 First Error Latch Value= 0-255
2 Acceleration Delay Seconds 1.0 Adjustable from 1.0 Flash Code
sec to 3.0 sec. NOTE: CL = Switch Closed
3 Deceleration Delay Seconds 0.5 Adjustable from 0.5 OP = Switch Open
sec. to 3.0 sec.
4 Traction Creep % 0 Adjustable from 0% to
10%
5 Max. allowed Speed % 65 Adjustable from 5% to
100%
6 Cutback Speed 1 % 20 Adjustable from 5% to
25%
7 Cutback Speed 2 % 75 Adjustable from 20%
to 75%
8 Pump Current limit Amps 270 Adjustable from 50
amps to 600 amps
9 Cutback1 Plug Current Amps 400 Adjustable from 180
amps to 750 amps
10 CSC Proportional Gain 1 30 Adjustable from 1 to
100
11 CSC Integral Gain 1 20 Adjustable from 1 to
100
12 Low Voltage Cutout Volts 25 Adjustable from 25
Volts to 40 Volts
13 Pump Acceleration Delay Seconds 2.0 Adjustable from 1.0 to
3.0
14 Pump Creep % 0% Adjustable from 0% to
30%

LX31/41 Electric/Bi-Energy Work Platform 4-7

 Section
4.8 TRO U B L E S H O O T I N G

4.8 MOS90 FAULT FINDING FLOW CHARTS

At battery connection, the LED should not illuminate.
At key ON, the LED should illuminate steadily. If the
LED illuminates and remains steady, but no drive can
be selected, the calibrator can be used to test the
wiring harness.

Check that both directions are not selected.

Check direction switches and wiring. Use
1 Flash calibrator test mode and check Fwd/Rev/Lift
switch inputs and wiring.
- Power up/Fail-safe Fault
- EEPROM data corrupted on
key Rectify

Fault appears at key switch on.

Replace MOS90 Controller

Replace MOS90 Controller

3 Flashes
- Point "A" less than 7V in
2 Flashes neutral, or less than 7V for
- Procedure Fault 15mS in drive, or contactor coil
shor t circuit.
- Illegal Star tup Sequence.
- Drive inhibited.
Two directions selected
together, direction and lift - Recycle to neutral to
selected together or lift and clear.
ground selected together NOTE: If recycling to neutral does not clear the
fault, then the fail-safe is due to a S/C contactor
- Drive inhibited coil and the keyswitch must be recycled (and the
coil replaced).
- Flashes until fault is
cleared
Check power and control wiring for shorts
Check for correct startup sequence. Was direc-
tion or lift selected at power up?
Rectify

Retry
Replace Controller

4-8 LX31/41 Electric/Bi-Energy Work Platform

 Section
TRO U B L E S H O O T I N G 4.8

4 Flashes 5 Flashes
- Direction contactor welded. - Direction contactors (or line
(Point "A" within 6V of B+ve contactor) did not close.
in neutral) - Motor armature or field
- Leakage between motor open circuit.
ar mature and field. - Point "A" not within 6V of
- Drive inhibited. B+ve within one second of
- Flashes in neutral until selecting direction.
fault is cleared - Drive inhibited.
- Flashes until fault is cleared,
Check direction contactor tips when contactor closes.

Check contactor tips

Free/change tips

Repair/replace

Check power wiring for shorts

Check contactor for mechanical operation and
coil O.K.

Rectify
Repair/replace

Check motor for armature to field shorts or

leakage Check power and control wiring

Rectify Rectify

Check for open circuit motor

Check for shorts to frame and battery leakage

Rectify
Rectify

Replace controller

Replace MOS90 Controller

LX31/41 Electric/Bi-Energy Work Platform 4-9

 Section
4.8 TRO U B L E S H O O T I N G

6 Flashes 7 Flashes
- Accelerator faults - Batter y voltage dipped below
- 3.5 Volts to 0 Volts = Min. to 14 volts
Max. Speed on accelerator - Drive inhibited
input (pin 14). Greater than - Turn key switch off and on to
4.5 volts can mean an open clear flash
accelerator pot. Less than 2.5
Volts on power up, indicates
Check battery voltage (under load) with a voltme-
more than 30% demand ter or calibrator
- Controller pulses at creep
setting
- Flashes until fault cleared Change/charge battery

Check operation of accelerator with test se-

quence Check power connections, fuses, etc.

Rectify/replace Repair/replace

Check pot operation with voltmeter for voltage at Check for battery leakage to frame
minimum setting

Rectify
Adjust as necessary or replace

Replace MOS90 Controller

Replace MOS90 Controller

4-10 LX31/41 Electric/Bi-Energy Work Platform

 Section
TRO U B L E S H O O T I N G 4.8

8 Flashes 10 Flashes
- Thermal cutback - Tachometer fault
- Heatsink temperature less - Drive inhibited
than 80ºC (176ºF) (Current - Recycle key to clear fault
limit will be zero at 90ºC
(194ºF)
Check tachometer wires for opens or shorts
- Allow unit to cool down, to
clear flashing
Rectify
Check current limit setting

Check output voltage from tachometer using

Re-set voltmeter

Check mounting and heatsink of controller Replace

Rectify Check output voltage from tachometer board,

using voltmeter

Check application is correct

Replace

Use larger controller

Replace MOS90 Controller

Replace MOS90 Controller

LX31/41 Electric/Bi-Energy Work Platform 4-11

 Section
4.8 TRO U B L E S H O O T I N G

11 Flashes 12 Flashes
- Tachometer signal out of - Severe tilt condition with
range platform raised above
- Drive inhibited 2 meters
- Flashes until fault cleared - Vehicle goes into emergency
stop (forced neutral state) and
plug brakes to a stop
Check tachometer wires for shorts to frame or a
voltage source - Recycle nuetral to clear fault

Use calabrator test mode and check platform up

Rectify switch and severe tilt switch inputs and wiring

Check output voltage from tachometer using Rectify

voltmeter

Replace MOS90 Controller

Replace

Replace MOS90 Controller

4-12 LX31/41 Electric/Bi-Energy Work Platform

 Section
TRO U B L E S H O O T I N G 4.8

14 Flashes LED off

- Battery voltage has fallen out - Unit not powered up or controller
of range. faulty, or LED faulty
- Traction and pump mode will
not be allowed Check battery is connected and keyswitch is on
- Requires key recycle to clear
fualt
Rectify
Check battery voltage (under load) with a voltme-
ter or calibrator
Check all fuses are intact

Change/charge battery
Rectify

Check power connections, fuses, etc.

Check supply wiring. Does calibrator unit still
function
Repair/replace

Rectify
Check for battery leakage to frame

Controller is faulty:
Rectify
a) Auto fail-safe check failed. LED turns off when
a direction is first selected after power up.
Recycle keyswitch.
b) Contactor drive S/C. LED resets itself if short
Replace MOS90 Controller circuit clears.
c) Mosfets did not turn on. Recycle direction to
neutral to clear fault indication.

Replace controller

LX31/41 Electric/Bi-Energy Work Platform 4-13

 Section
4.9 TRO U B L E S H O O T I N G

4.9 ACTIVATING "TEST" Connect voltmeter between B- and pin 14 on

MOS90. Voltage at pin 14 in neutral should not be
Position red LED at TEST. Press "+" or "-" to select lower than +3.5 volts D.C. 3.5 VDC = 0% speed input,
the switch to be viewed. 0.0 VDC=100% speed input.
The zero position input "-" should read zero and is set If set at an extremely high value MOS90 will read as
by adjusting the sensitivity threshold trim pot in the fault and shut down.
upper control box. Step on the foot switch and keep-
Properly set the LX31/41 should start to move slowly
ing the joystick centered, adjust the pot to give a
with a small movement of the joystick after a very
readout of 1 or 2. Slowly back the pot down until the
small "deadband" zone.
reading has just dropped to zero.

Pump/Traction
1 Black
Tachometer direction input from tach board (18 Volts = rev. & 0 Volts = FWD.
2 Brown
No connection
3 Red (spare)
Height Limit
4 Orange
Battery + side of direction & brake contactors for coil suppression (48 Volts)
5 Yellow

MOS90
+ 48 Volt supply to power up controller
6 Green
Tilt
7 Blue
48 Volts when forward is selected & 0 Volts in neutral
8 Purple
No connection Grey (spare)
9
No connection
10 White (spare)
48 Volts when reverse is selected & 0 Volts in neutral
11 Pink
Tach signal from tach gen. (7.5 Volts to 15 Volts = FWD. 0-100% and 7.5
Volts to 0 Volts = REV. 0-100% White/Purple
12
High/Low Speed
13 White/Red
Traction accelerator signal (3.5 Volts to 0 Volts = min. to max. speed)
14 White/Black
Forward contactor driver - goes to battery negative to energize contactor
15 White/Yellow
Brake applied input (48 Volts = brake on & 0 Volts = brake off)
16 White/Blue
Reverse contactor driver - goes to battery negative to energise contactor
17 White/Green

Figure 4-2: MOS90 17 Way Connector Pinout Designation

4-14 LX31/41 Electric/Bi-Energy Work Platform

 Section
TRO U B L E S H O O T I N G 4.9

Battery Positive supply

(48 Volts) Battery Negative Supply
1
A Tach speed signal to pin 12 of MOS90
2
Fuse Input from tach generator
No connection F1 3
Tach direction signal to pin 2 of MOS90
B 4
Input from tach generator
5
No connection
C 6
Output over speed relay con- 7
nects to pin 7 of MOS90
D 8
Battery positive to over speed 9
Tach
relay (48 Volts) 10
E Circuit No connection
Over 11
speed 12
relay
13
14 Tach generator
15
16

D 48 Volts = no over speed condition 2 Tach speed signal from tach board
0 Volts = over speed condition 7.5 Volts to 15 volts = 0-100% speed in FWD.
7.5 Volts to 0 volts = 0-100% speed in REV.

4 Tach direction signal

18 Volts = REV.
0 Volts = FWD.

5 Output of tach generator

0 to +50 Volts = 0-100% speed in FWD.
0 to -50 Volts = 0-100% speed in REV.
Figure 4-3: Upright Tachometer Board

LX31/41 Electric/Bi-Energy Work Platform 4-15

 Section
4.9 TRO U B L E S H O O T I N G

4-16 LX31/41 Electric/Bi-Energy Work Platform

 Section 5
SCHEMATICS
Introduction Schematic Page
This section contains electrical and hydraulic power 5.1 Electrical Schematic, Bi-Energy. . . . . . . . . . . . . 5-2
schematics and associated information for mainte- 5.2 Electrical Schematic, Electric . . . . . . . . . . . . . . 5-4
nance purposes.
5.3 Hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
The diagrams are to be used in conjunction with the
Troubleshooting Truth Tables in Section 4. They 5.4 Component Identification . . . . . . . . . . . . . . . . . . 5-8
allow understanding of the makeup and functions of
the systems for checking, tracing, and faultfinding
during troubleshooting analysis.
The components that comprise the electrical and
hydraulic systems are given a reference designation
and are explained as to function and location in the
following tables.

LX31/41 Electric/Bi-Energy Work Platform 5-1

 Section
5.1 SCHEMATICS
5.1 ELECTRICAL SCHEMATIC, BI-ENERGY
Table 5-1: Electrical Schematic - 067447-002

REFERENCE REFERENCE
NAME FUNCTION LOCATION NAME FUNCTION LOCATION
DESIGNATION DESIGNATION

Warning sound when machine is Prevent Pump Start

ALM1 Alarm, Tilt Lower Control Box R17 Power to Pump Start Switch Upper Controls
off-level Relay
Warning sound when deck is Lower Control Box R18 Starter Relay Power to Starter Motor Engine Assembly
ALM2 Alarm, Down
lowering R19 Glow Plug Relay Power to Glow Plug Engine Assembly
BAT1 Battery Electrical Power Control Module R20 Oil Pressure Relay Power to S23 Engine Assembly
BAT2 Battery Electrical Power to Engine Control Module RES1 Resistor Pack Current Protection Relay Panel
Main Power Switch Power to All Solenoids Resistor, Drive Limit Current to Drive Enable
C1 Contactor and Motors Relay Panel RES2 Upper Controls
Enable Light Light
C2 Forward Contactor Switch Drive Motors to Forward Relay Panel Joystick Interlock
S1 Switch Enable Upper Control Functions Front of Joystick
C3 Reverse Contactor Switch Drive Motors to Reverse Relay Panel
Pump Override S2 Interlock Switch Enable Drive Upper Controls
C4 Overide Pump Motors Relay Panel
Contactor S3 Interlock Switch Enable lift Upper Controls
Pump/Traction Switch Power Between Drive Lower Emergency
C5 Contactor Motors and Pump Motors Relay Panel S4 Stop All Functions Lower Controls
Stop Switch
CB1 Circuit Breaker Protect Emerg. Stop Switch S4 Lower Control Box Provide Power to Up Relay &
S5 Lift Switch Lower Controls
CB2 Circuit Breaker Protect Power Relay R9 Lower Control Box Down Relay
CB3 Circuit Breaker Protect Engine Wiring Lower Control Box S6 Brake release Switch Provide Power to Brake release Lower Controls
Relay
CH1 Battery Charger Charge Batteries Control Module
S7 Drive Switch Activate Drive Upper Controls
CONT Controller Control Logic Module Relay Panel
S8 Lift Switch Activate Lift Upper Controls
D1 Diode Spike Protection Between T10 & T13
S9 High/Low Switch Speed Control Upper Controls
D2 Diode Spike Protection Between T20 & T17
Platform Down Close when Platform is Fully Bottom of Elevating
D3 Diode Spike Protection Between T14 & T17 S10 - S13
Switch Down Assembly
D4 Diode Power to Down Relay Control Module 8 Meter Cutout Stop Drive Function when
S14 Switch Platform Reaches 8 Meters Chassis
D5 & D6 Diode Power to Power Relay Control Module
D7 - D10 Diode Power to Pump Start Relay Control Module S15 Up Limit Switch Stop Lift Function Chassis
Power to Brake Release Relay Provide Power to Pump Start Brake Valve
D11 Diode Control Module S16 Pump Start Switch
R11 Relay Manifold
D12 Diode Power to Hour Meter Control Module S17 Chassis/Platform Power to Either Upper or Lower Lower Control Box
D13 Diode Power to Start Relay Control module Switch Controls
D14 Diode Protect Main Power Contactor Control Module Upper Emergency
S18 Stop All Functions Upper Controls
Stop Switch
D15 Diode Power to Down Alarm Control Module
S19 Steering Rocker Power to Steering Relays Top of Joystick
F1 & F2 Fuse, Main Protect Circuit Wiring Relay Panel Switch
F9 Fuse Protect Engine Wiring Control Module Proportional Speed Control Speed of Motors for
S20 Joystick
GEN Generator Power to Battery Charger Power Module Control Drive and Lift
L1 Drive Enable Light Indicate Power to Drive Circuit Upper Controls S21 Ignition Switch Power to Upper Controls & Upper Controls
(keyswitch) Motors
M1 Hour Meter Record Operating Time Lower Control Box
S22 Start Switch Start Generator Engine Upper Controls
MOT1 & 2 Electric Motor Drive Hydraulic Pump Power Module
Oil Pressure Switch Stop EngineToo
when Oil Pressure
MOT3 Electric Motor Drive Left Rear Wheel Chassis S23 Low Engine Assembly
MOT4 Electric Motor Drive Right Rear Wheel Chassis S24 Glow Plug Switch Power to Glow Plug Upper Controls
P1 Fuel Pump Supply Fuel to Generator Engine Power Module Electrical Power to Engine
S25 Engine Run Switch Lower Control Box
R1 Drive/Lift Relay Start Hyd Pumps Lower Control Box Assembly
8 Meter Cutout S26 Charge Switch Power to Charge Relay Lower Control Box
R2 Drive Cutout Lower Control Box
Relay S27 Starter Switch Power to Starter Relay Lower Control Box
R3 Tilt Alarm Relay Switch Power to ALM1 Lower Control Box S28 Glow Plug Switch Power to Glow Plug Relay Lower Control Box
R4 Up Relay Switch Power to SOL1 & 2 Lower Control Box SEN1 Level Sensor Stop Drive Function Control Module
R5 Down Relay Switch Power to SOL3 Lower Control Box SOL 1 & 2 Up Solenoid Control Lift Valve Manifold
R6 Down Alarm Relay Switch Power to ALM2 Lower Control Box SOL3 Down Solenoid Control Down Valve Manifold
R7 Steer Right Relay Switch Power to SOL5 Lower Control Box SOL5 Steer Right Solenoid Control Steer Right Valve Top of Manifold
R8 Steer Left Relay Switch Power to SOL6 Lower Control Box SOL6 Steer Left Solenoid Control Steer Left Valve Top of Manifold
R9 Pump Start Relay Provide Power to S1 Lower Control Box SOL8 Brake Solenoid Control Brake Valve (powers on) Manifold
R10 Brake Relay Switch Power to SOL8 Lower Control Box Brake Release
SOL11 Solenoid Control Brake Valve (powers off) Manifold
R11 Brake Release Relay Switch Power to SOL11 Lower Control Box
R12 Power Relay Switch Power to All Relays Lower Control Box SOL12 Stop/Run Solenoid Allow Engine to run Power Module
R13 Start Relay Start Engine Lower Control Box Tachometer -
TG1 & TG2 Monitor Drive Motor Speed Control Module
R14 Charge Relay Charge 12V Battery Lower Control Box Generator
Provide Power to Brake Relay Relay Panel
R15 Brake Release Relay
R10 Assembly
Platform Power
R16 Power to Upper Controls Upper Controls
Relay

5-2 LX31/41 Electric/Bi-Energy Work Platform

 Section
SCHEMATICS 5.1

L1 RES2
R1 R15

R2
S7
S20 S3

S8 D1 ALM1
S2 D4
S9 R3
S1 SOL1 C5
S19 S14 R4
D2
D3 SEN1 S15 SOL2
R17 R16 S24 RES1 MOT3 MOT4
S11 CONT
S22 S10 CH1
S18
S13 SOL3
S21
R5
S12
CB3 D15 ALM2 BAT1
S4 R6
F9 CB1
BAT2
CB2 SOL5
R7 C2 C3
R18 S26 S17
S27 R8 SOL6 C1
S5
D12
R19 S28
S6
D7 D8 R9 MOT1
D9 D10
M1 S16 F1
R11 SOL11
S25 F2
D11
R10 MOT2
SOL12
GEN
D5 D6 D13 SOL8
R20 TG1 TG2
R13 C4
S23 P1 R12
R14

D14

Figure 5-1: Electrical Schematic, Bi-Energy (067447-002)

LX31/41 Electric/Bi-Energy Work Platform 5-3

 Section
5.2 SCHEMATICS
5.2 ELECTRICAL SCHEMATIC, ELECTRIC
Table 5-2: Electrical Schematic, 067447-003

REFERENCE REFERENCE
NAME FUNCTION LOCATION NAME FUNCTION LOCATION
DESIGNATION DESIGNATION

Warning sound when machine is S4 Lower Emergency Stop All Functions Lower Controls
ALM1 Alarm, Tilt off-level Lower Control Box Stop Switch
Warning sound when deck is S5 Lift Switch Provide Power to Up Relay & Lower Controls
ALM2 Alarm, Down lowering Lower Control Box Down Relay
BAT1 Battery Electrical Power Control Module Brake release Provide Power to Brake release
S6 Switch Relay Lower Controls
C1 Main Power Switch Power to All Solenoids Relay Panel
Contactor and Motors S7 Drive Switch Activate Drive Upper Controls
Forward S8 Lift Switch Activate Lift Upper Controls
C2 Switch Drive Motors to Forward Relay Panel
Contactor S9 High/Low Switch Speed Control Upper Controls
C3 Reverse Contactor Switch Drive Motors to Reverse Relay Panel Platform Down Close when Platform is Fully Bottom of Elevating
S10 - S13 Switch Down Assembly
Pump Override
C4 Contactor Overide Pump Motors Relay Panel
8 Meter Cutout Stop Drive Function when
S14 Switch Platform Reaches 8 Meters Chassis
Pump/Traction Switch Power Between Drive
C5 Contactor Motors and Pump Motors Relay Panel
S15 Up Limit Switch Stop Lift Function Chassis
Protect Emergency Stop Switch Pump Start Provide Power to Pump Start Brake Valve Manifold
CB1 Circuit Breaker S4 Lower Control Box S16
Switch Relay
CB2 Circuit Breaker Protect Power Relay R9 Lower Control Box Chassis/Platform Power to Either Upper or Lower Lower Control Box
S17 Switch Controls
CH1 Battery Charger Charge Batteries Control Module
CONT Controller Control Logic Module Relay Panel Upper Emergency
S18 Stop All Functions Upper Controls
Stop Switch
D1 Diode Spike Protection Between T10 & T13
Steering Rocker
D2 Diode Spike Protection Between T20 & T17 S19 Switch Power to Steering Relays Top of Joystick
D3 Diode Spike Protection Between T14 & T17 Proportional Control Speed of Motors for
S20 Speed Control Drive and Lift Joystick
D4 Diode Power to Down Relay Control Module
D5 & D6 Diode Power to Power Relay Control Module S21 Ignition Switch Power to Upper Controls & Upper Controls
D7 - D10 Diode Power to Pump Start Relay Control Module (keyswitch) Motors
D11 Diode Power to Brake Release Relay Control Module SEN1 Level Sensor Stop Drive Function Control Module
D12 Diode Power to Hour Meter Control Module SOL 1 & 2 Up Solenoid Control Lift Valve Manifold
D15 Diode Power to Down Alarm Control Module SOL3 Down Solenoid Control Down Valve Manifold
F1 & F2 Fuse, Main Protect Circuit Wiring Relay Panel Steer Right
SOL5 Solenoid Control Steer Right Valve Top of Manifold
L1 Drive Enable Light Indicate Power to Drive Circuit Upper Controls
SOL6 Steer Left Control Steer Left Valve Top of Manifold
M1 Hour Meter Record Operating Time Lower Control Box Solenoid
MOT1 & 2 Electric Motor, Drive Hydraulic Pump Power Module SOL8 Brake Solenoid Control Brake Valve (powers on) Manifold
Power Unit
Brake Release Control Brake Valve (powers off)
MOT3 Electric Motor Drive Left Rear Wheel Chassis SOL11 Manifold
Solenoid
MOT4 Electric Motor Drive Right Rear Wheel Chassis Tachometer -
TG1 & TG2 Monitor Drive Motor Speed Control Module
R1 Drive/Lift Relay Start Hydraulic Pumps Lower Control Box Generator
8 Meter Cutout
R2 Relay Drive Cutout Lower Control Box
R3 Tilt Alarm Relay Switch Power to ALM1 Lower Control Box
R4 Up Relay Switch Power to SOL1 & 2 Lower Control Box
R5 Down Relay Switch Power to SOL3 Lower Control Box
R6 Down Alarm Relay Switch Power to ALM2 Lower Control Box
R7 Steer Right Relay Switch Power to SOL5 Lower Control Box
R8 Steer Left Relay Switch Power to SOL6 Lower Control Box
R9 Pump Start Relay Provide Power to S1 Lower Control Box
R10 Brake Relay Switch Power to SOL8 Lower Control Box
R11 Brake Release Switch Power to SOL11 Lower Control Box
Relay
R12 Power Relay Switch Power to All Relays Lower Control Box
Brake Release Provide Power to Brake Relay
R15 Relay Panel
Relay R10
Platform Power
R16 Power to Upper Controls Upper Controls
Relay
Prevent Pump
R17 Power to Pump Start Switch Upper Controls
Start Relay
RES1 Resistor Pack Current Protection Relay Panel
Resistor, Drive Limit Current to Drive Enable
RES2 Upper Controls
Enable Light Light
Joystick Interlock Enable Upper Control Functions
S1 Front of Joystick
Switch
S2 Interlock Switch Enable Drive Upper Controls
S3 Interlock Switch Enable lift Upper Controls

5-4 LX31/41 Electric/Bi-Energy Work Platform

 Section
SCHEMATICS 5.2

L1 RES2
R1 R15

R2
S20 S3 S7

S8 D1 ALM1
S2 D4
S9 R3
S1 SOL1
S14
D2 C5
S19 D3 R4 SOL2
R16 SEN1 S15 MOT4
RES1 MOT3
S11 CONT
S21 S10
R17 CH1
S18
S12 S13
SOL3
R5
CB1 S4 BAT1
D15 ALM2
CB2 R6
SOL5
S17 C2 C3
R7
S5 SOL6 C1
D12 R8
S6 MOT1
D9 D7 D8 R9
M1
S16 F1
D10 R11 SOL11 F2
D11 MOT2
R10
D5
D6 SOL8 TG1 TG2
R12
C4

LX31/41 Electric/Bi-Energy Work Platform 5-5

 Section
5.3 SCHEMATICS
5.3 Electrical Schematic, Electric (067447-003)HYDRAULICS

Table 5-3: Hydraulic Schematic - 067446-000

REFERENCE
NAME FUNCTION LOCATION
DESIGNATION
ACC Accumulator Accumulate Hydraulic Fluid Brake Valve Block
CV1 Check Valve Slow Brake Release Brake Valve Block
CV2 Check Valve Reduce Platform Lowering Lift Cylinder
Speed
CYL1 Cylinder, Left Apply Left Brake Pressure Left Brake
Brake
CYL2 Cylinder, Right Apply Right Brake Pressure Right Brake
Brake
CYL3 Cylinder, Lift Actuate Scissor Linkage to Chassis
Lift Platform
CYL4 Cylinder, Actuate Steering Linkage to Chassis
Steering Steer Front Wheels
F1 Filter, Return Filter Hydraulic Line Tank
F2 Filter, Tank Filter Contaminants Tank
ORF1 Orifice, Steering Limit Hydraulic Oil Flow to Main Valve Block
Steering Cylinder
ORF2 Orifice, Brake Allow Brakes to Release Brake Valve Block
Quickly and Apply Slowly
ORF3 Orifice, Lift Limit Hydraulic Oil Flow to Lift Cylinder
Lift Cylinder
P1 & P2 Hydraulic Pump Provide Fluid Power for Chassis
Hydraulic System
RV1 Valve, Main Provide Over Pressure Main Valve Block
Relief Protection for the Main
Hydraulic Line
RV2 Valve, Steering Provide Over Pressure Main Valve Block
Relief Protection for the Steering
Components
S1 Pressure Switch Disable Machine Brake Valve Block
V1 Valve, Brake Direct Hydraulic Oil to the Brake Valve Block
Apply Brake Cylinders
V2 Valve, Brake Release Hydraulic Oil Brake Valve Block
Release Pressure from Brakes
V3 Valve, Steering Control Hydraulic Oil Flow to Main Valve Block
Steering Cylinder
V4 Valve, Lift Control Hydraulic Oil Flow to Main Valve Block
Lift Cylinder
V5 Valve, Dump Divert Excess Oil Main Valve Block
V6 Valve, Down - Hold Oil in Lift Cylinder Lift Cylinder
when Deck is Elevated.
- Release Oil from Lift
Cylinder to Lower Deck
- Has Cable Actuated
Manual Override for
Emergency Lowering

5-6 LX31/41 Electric/Bi-Energy Work Platform

 Section
SCHEMATICS 5.3

CYL4

CYL3
ORF3
CV2
CYL1 CYL2
V6

V3

RV2 V4

V2 FD1
V1
RV1
CV1

ORF2
V5

S1
ACC

P1 P2
F1
F2

Figure 5-3: Hydraulic Schematic - 067446-000

LX31/41 Electric/Bi-Energy Work Platform 5-7

 Section
5.4 SCHEMATICS
5.4 COMPONENT IDENTIFICATION

6
Typical Retainer Installation

4 5
d e Retainer Catch to be
Positioned to the Inside
1

a 3

a. End Bracket 7
b. Terminal Block (Blue)
c. Terminal Block
2
d. Relay, DPDT R17
e. Relay, SPDT R16
f. Terminal Block (Ground)

c
b 10
f

8
15
16
16
9
16 10
11

12
9
1

3
4 11
5
13

14 Upper Control Box

1. Emergency Stop Button
6 2. Drive/Lift Switch
3. Speed Range Switch
7 4. Joystick
5. Interlock Switch
8 6. Rocker Switch (steering)
8 16 7. Drive Enable Light
8. Glow Plug Button (Bi-Energy)
Lower Control Box 9. Key Switch
1. Emergency Stop Button 9. Glow Plug Button (Bi-Energy) 10. Relay
2. 3-Position Selector Switch 10. Start Button (Bi-Energy) 11. Cable Connector
(Platform/Chassis/Brake Release) 11. Ignition Key Switch (Bi-Energy)
3. Raise Button 12. Hour Meter
4. Brake Release Button 13. Down Alarm Figure 5-5: Upper Control Box Assembly
5. Lower Button 14. Tilt Alarm
6. Cable Connector, 3/4 15. Panel Assembly
7. Cable Connector, 1/2 16. Plug (Electric)
8. Circuit Breaker, 10 AMP

Figure 5-4: Lower Control Box Assembly

5-8 LX31/41 Electric/Bi-Energy Work Platform

 Section
SCHEMATICS 5.4
CHA
RGE
STAR V3
BRA POW T
KE R
E
ER RV2 RV
L
PUM BRAKE EASE
ST P ST
STE EER L ART
DOW ER RIG EFT FD
N AL HT
DOW
N
ARM V4
UP
TILT
8
CUT METER
O
DRIV UT
LIFT E

ers
u mb
yN V5
R ela

Figure 5-6: Lower Control Box Relays

C5

RES C4

C
R5
C3

C2

Figure 5-9: Valve Manifold, Exploded View

F F2

Guage Port Plug V2

TG TG2
rake Release
CONT Poppet Vale N.C.
4VDC
S
Pressure Switch
V
rake Apply
Poppet Vale N.O.
4VDC

Figure 5-7: Relay Panel Assembly

Pipe Nipple

Figure 5-10: Brake Valve Manifold, Exploded View

3
2
1

1. R18 - Start Relay

2. R19 - Glow Plug Relay
3. R20 - Oil Pressure

Figure 5-8: Engine Relays (Bi-Energy)

LX31/41 Electric/Bi-Energy Work Platform 5-9

 Section
5.4 SCHEMATICS

5-10 LX31/41 Electric/Bi-Energy Work Platform

 Section 6
ILLUSTRATED PARTS BREAKDOWN
Introduction
This section lists and illustrates the replaceable assemblies and parts of this product, as manufactured by UpRight, Inc.
Each parts list contains the component parts for that assembly.

CONTENTS
Final Assembly, LX31 Electric Guardrail Installation, LX31/41 Electric & Bi-Energy - Dual
067430-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Deck
Final Assembly, LX31 Bi-Energy 030841-300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-52
067350-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Hose Kit Installation, LX31/41
Final Assembly, LX41 Electric 067383-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-54
067431-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6 Lower Control Box Assembly, LX31/41
Final Assembly, LX41 Bi-Energy 067362-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-56
067351-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 Controller Assembly 48V, LX31/41 Electric
Final Assembly, LX31 Electric - Dual Deck 067384-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-58
067435-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10 Controller Assembly 48V, LX31/41 Bi-Energy
Final Assembly, LX31 Bi-Energy - Dual Deck 067384-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-60
067370-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12 Scissors Guard, LX31 Bi-Energy
Final Assembly, LX41 Electric - Dual Deck 067373-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-62
067436-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14 Scissors Guard, LX41 Bi-Energy
Final Assembly, LX41 Bi-Energy - Dual Deck 067373-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-63
067371-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16 Scissors Guard, LX31 Electric
Basic Assembly, LX31 Electric & Bi-Energy 067373-003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-64
067354-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18 Scissors Guard, LX41 Electric
Basic Assembly, LX41Electric & Bi-Energy 067373-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-65
067355-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20 Tire & Wheel Assembly, Front, LX31/41
Basic Assembly, LX41Electric & Bi-Energy - Dual Deck 067665-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-66
067374-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22 Tire & Wheel Assembly, Rear, LX31/41
Basic Assembly, LX41Electric & Bi-Energy - Dual Deck 068327-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-67
067375-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24 Valve Block Assembly, LX31/41
Chassis Assembly, LX31/41 067389-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-84
067358-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-26 Brake Valve Block Assembly, LX31/41
Power Module Assembly, LX31/41 Electric 068324-002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-85
067359-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-32 Slide-Out Deck Installation, LX31/41
Power Module Assembly, LX31/41 Bi-Energy 067866-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-86
067359-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-34 Amber Beacon Option, LX31/41
Engine Assembly, LX31/41 Bi-Energy 067947-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-87
067391-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-36 Horn Option, LX31/41
Control Module Assembly, LX31/41 Bi-Energy 067908-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-88
067360-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-38 Motion Alarm Option, LX31/41
Control Module Assembly, LX31/41 Electric 067909-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-89
067360-005 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-41 Poly Fill Tire Option, LX31/41 2 Wheel Drive
Control Module Assembly, LX31/41 Bi-Energy - Dual Deck 067910-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-90
067360-006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-44 067665-005 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-90
Control Module Assembly, LX31/41 Electric - Dual Deck 068327-003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-90
067360-007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-47 Removable Controller Option, LX31/41
Guardrail Installation, LX31/41 Electric & Bi-Energy 061898-002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-91
067530-005 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-50

LX31/41 Electric/Bi-Energy Work Platform 6-1

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Final Assembly, LX31 Electric
067430-001
ITEM PART NO DESCRIPTION QTY. ITEM PART NO DESCRIPTION QTY.

1 067354-000 BASIC ASSY 1 23 063497-001 MERCURY SWITCH 2

2 067384-002 CONTROLLER ASSY 1 24 013919-013 CLAMP 2
3 067536-000 CONTROL CABLE ASSY 1 25 014996-004 WASHER 1/4 SAE FLAT 4
4 067361-009 DECAL-KIT 1 30 067473-000 SWITCH MOUNT 1
5 067383-000 HOSE-KIT 1 33 015963-099 STRAP MATL. 9
6 067530-005 GUARDRAIL 1 201 068776-048 CABLE ASSY X 48” (3/8 X 3/8 LUG) 2
7 067359-001 POWER MODULE 1 202 068776-014 CABLE ASSY X 165” (3/8 X 3/8 LUG) 2
8 067360-001 CONTROL MODULE 1 204 068776-012 CABLE ASSY X 150” (3/8 X 3/8 LUG) 2
9 067446-000 HYD SCHM. REF 206 010154-001 BATTERY TERM. COVER 10
10 067447-003 ELEC. SCHM. REF 210 068777-107 CABLE ASSY X 107” (3/8 X 5/16 LUG) 2
12 067692-000 CLIP, CABLE RETAINER 4 211 029452-099 WIRE, 16 GA. BLACK 5FT
13 020032-001 TEE, #4MJ-#4MJ-#4MJ 1 216 029355-099 WIRE, 16 GA. BLK/RED 5FT
15 011252-006 SCRW, 1/4-20 X 3/4 2 217 029496-099 WIRE, 16 GA. 2 CON 16FT
16 011248-004 LOCKNUT, 1/4-20 UNC 3 218 014914-001 CONN. MALE PUSH, 14-16 .25 2
17 011248-003 LOCKNUT, 10-24 UNC 4 219 029931-003 CONN. FEM. PUSH, 14-16 .25 2
18 011709-008 SCREW 10-24 UNC X 1 4 220 029601-012 CONN. RING, 14-16 #8 8
19 011240-003 WASHER #10 STD FLAT 2 221 029601-015 CONN. RING, 14-16 N 3/8 1
20 066490-000 SWITCH ROLLER 16 222 029825-002 DIODE, 3 AMP, 400 VOLT 6
21 029447-099 CABLE 3 COND. 16 GA. 10 FT 225 060214-099 WIRE, 16 AWG 15 CONN. 18FT
22 029620-002 CONN. BUTT 16-14 GA. 13 226 029620-002 CONN. BUTT 16-14 3

Final
Assembly
067430-001

6-2 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Final Assembly
067430-001
Drawing 2 of 2

LX31/41 Electric/Bi-Energy Work Platform 6-3

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Final Assembly, LX31 Bi-Energy
067350-001
ITEM PART NO DESCRIPTION QTY ITEM PART NO DESCRIPTION QTY

1 067354-000 BASIC ASSY 1 30 067863-000 SWITCH MOUNT 1

2 067384-000 CONTROLLER ASSY 1 33 015963-099 STRAP MATL. 9
3 067536-000 CONTROL CABLE ASSY 1 34 015964-000 STRAP HEAD 9
4 067361-003 DECAL-KIT 1 35 012865-099 WIRE LOOM 3/4 DIA 8
5 067383-000 HOSE-KIT 1 201 068776-048 CABLE ASSY. X 48” (3/8 X 3/8 LUG) 2
6 067530-005 GUARDRAIL 1 202 068776-014 CABLE ASSY. X 165” (3/8 X 3/8 LUG) 1
7 067359-000 POWER MODULE 1 204 068776-012 CABLE ASSY. X 150” (3/8 X 3/8 LUG) 1
8 067360-004 CONTROL MODULE 1 205 068777-001 CABLE ASSY. X 41” (5/16 X 3/8 LUG) 1
9 067446-000 HYD SCHM. REF 206 068777-002 CABLE ASSY. X 47” (5/16 X 3/8 LUG) 1
10 067447-002 ELEC. SCHM. REF 207 068777-123 CABLE ASSY. X 123” (5/16 X 3/8 LUG) 2
12 067692-000 CLIP, CABLE RETAINER 4 208 068777-100 CABLE ASSY. X 100” (5/16 X 3/8 LUG) 2
13 020032-001 TEE, #4MJ-#4MJ-#4MJ 1 210 068777-107 CABLE ASSY. X 107” (3/8 X 5/16 LUG) 2
15 011252-006 SCRW, 1/4-20 X 3/4 2 211 029452-099 WIRE, 16 GA. BLACK FT 5
16 011248-004 LOCKNUT, 1/4-20 UNC 3 212 067990-021 CONNECTOR 1
17 065373-006 MAGNET 4 213 068762-001 CONNECTOR SOCKET 4
18 065373-005 SWITCH 4 214 067990-022 LOCKING WEDGE 1
19 067913-000 ALUM. SW. PAD 2 216 029355-099 WIRE 16 GA BLK/RED FT 5
20 026551-005 RIVET 1/8 X 1/4 GRIP 16 217 029496-099 WIRE 16 GA 2 CON FT 16
21 029447-099 CABLE 3 COND. 16 GA. 10 FT 218 014914-001 CONN. MALE PUSH, 14-16 .25 2
22 029620-002 CONN. BUTT 16-14 GA. 13 219 029931-003 CONN. FEM. PUSH, 14-16 .25 2
23 063497-001 MERCURY SWITCH 2 220 029601-012 CONN. RING, 14-16 #8 8
24 013919-013 CLAMP 2 221 029601-015 CONN. RING, 14-16 Ø 3/8 1
25 014996-004 WASHER 1/4 SAE FLAT 4 222 029825-002 DIODE, 3 AMP, 400 VOLT 6
27 013283-002 CABLE MOUNT 6 225 060214-099 WIRE 16 AWG 15 C0NN FT 18
28 067758-099 NYLON HOSE GUARD 3 226 029620-002 CONN. BUTT 16-14 3

Final Assembly
067350-001
Drawing 1 of 2

6-4 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Final Assembly
067350-001
Drawing 2 of 2

LX31/41 Electric/Bi-Energy Work Platform 6-5

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Final Assembly, LX41 Electric
067431-001
ITEM PART NO DESCRIPTION QTY ITEM PART NO DESCRIPTION QTY

1 067355-000 BASIC ASSY 1 24 013919-013 CLAMP 2

2 067384-002 CONTROLLER ASSY 1 25 014996-004 WASHER, 1/4 SAE FLAT 4
3 067536-001 CONTROL CABLE ASSY 1 30 067863-000 SWITCH MOUNT 1
4 067361-010 DECAL-KIT 1 33 015963-099 STRAP MATL. 9
5 067383-000 HOSE-KIT 1 34 015964-000 STRAP HEAD 9
6 067530-005 GUARDRAIL 1 35 012865-099 WIRE LOOM 3/4 DIA 8
7 067359-001 POWER MODULE 1 201 068776-048 CABLE ASSY X 48” (3/8 X 3/8 LUG) 2
8 067360-001 CONTROL MODULE 1 202 068776-014 CABLE ASSY X 165” (3/8 X 3/8 LUG) 2
9 067446-000 HYD SCHM. REF 204 068776-012 CABLE ASSY X 150” (3/8 X 3/8 LUG) 2
10 067447-001 ELEC. SCHM. REF 206 010154-001 BATTERY TERM. COVER 10
12 067692-000 CLIP, CABLE RETAINER 8 210 068777-107 CABLE ASSY X 107” (3/8 X 5/16 LUG) 2
13 020032-001 TEE, #4MJ-#4MJ-#4MJ 1 211 029452-099 WIRE, 16 GA. BLACK 5FT
15 011252-006 SCRW, 1/4-20 X 3/4 2 216 029355-099 WIRE, 16 GA. BLK/RED 5FT
16 011248-004 LOCKNUT, 1/4-20 UNC 3 217 029496-099 WIRE, 16 GA. 2 CON 16FT
17 065373-006 MAGNET 4 218 014914-001 CONN. MALE PUSH, 14-16 .25 2
18 065373-005 SWITCH 4 219 029931-003 CONN. FEM. PUSH, 14-16 .25 2
19 067913-000 ALUM. SW. PAD 2 220 029601-012 CONN. RING, 14-16 #8 8
20 026551-005 RIVET 1/8 X 1/4 GRIP 16 221 029601-015 CONN. RING, 14-16 N 3/8 1
21 029447-099 CABLE 3 COND. 16 GA. 10 FT 222 029825-002 DIODE, 3 AMP, 400 VOLT 6
22 029620-002 CONN. BUTT 16-14 GA. 13 225 060214-099 WIRE, 16 AWG 15 CONN. 18FT
23 063497-001 MERCURY SWITCH 2 226 029620-002 CONN. BUTT 16-14 3

Final Assembly
067431-001
Drawing 1 of 2

6-6 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Final Assembly
067431-001
Drawing 2 of 2

LX31/41 Electric/Bi-Energy Work Platform 6-7

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Final Assembly, LX41 Bi-Energy
067351-001
ITEM PART NO DESCRIPTION QTY ITEM PART NO DESCRIPTION QTY

1 067355-000 BASIC ASSY 1 33 015963-099 STRAP MATL. 9

2 067384-000 CONTROLLER ASSY 1 34 015964-000 STRAP HEAD 9
3 067536-001 CONTROL CABLE ASSY 1 35 012865-099 WIRE LOOM 3/4 DIA 8
4 067361-004 DECAL-KIT 1 201 068776-048 CABLE ASSY. X48” (3/8 X 3/8 LUG) 2
5 067383-000 HOSE-KIT 1 202 068776-014 CABLE ASSY. X 165” (3/8 X 3/8 LUG) 1
6 067530-005 GUARDRAIL 1 204 068776-012 CABLE ASSY. X 150” (3/8 X 3/8 LUG) 1
7 067359-000 POWER MODULE 1 205 068777-001 CABLE ASSY. X 41” (5/16 X 3/8 LUG) 1
8 067360-004 CONTROL MODULE 1 206 068777-002 CABLE ASSY. X 47” (5/16 X 3/8 LUG) 1
9 067446-000 HYD SCHM. REF 207 068777-123 CABLE ASSY. X 123” (5/16 X 3/8 LUG) 2
10 067447-002 ELEC. SCHM. REF 208 068777-100 CABLE ASSY. X100” (5/16 X 3/8 LUG) 2
12 067692-000 CLIP, CABLE RETAINER 8 210 068777-107 CABLE ASSY. X 107” (3/8 X 5/16 LUG) 2
13 020032-001 TEE, #4MJ-#4MJ-#4MJ 1 211 029452-099 WIRE, 16 GA. BLACK 5
15 011252-006 SCRW, 1/4-20 X 3/4 2 212 067990-021 CONNECTOR 1
16 011248-004 LOCKNUT, 1/4-20 UNC 3 213 068762-001 CONNECTOR SOCKET 4
17 065373-006 MAGNET 4 214 067990-022 LOCKING WEDGE 1
18 065373-005 SWITCH 4 216 029355-099 WIRE 16 GA BLK/RED 5
19 067913-000 ALUM. SW. PAD 2 217 029496-099 WIRE 16 GA 2 CON 16
20 026551-005 RIVET 1/8 X 1/4 GRIP 16 218 014914-001 CONN. MALE PUSH, 14-16 .25 2
21 029447-099 CABLE 3 COND. 16 GA. 10 FT 219 029931-003 CONN. FEM. PUSH, 14-16 .25 2
22 029620-002 CONN. BUTT 16-14 GA. 13 220 029601-012 CONN. RING, 14-16 #8 8
23 063497-001 MERCURY SWITCH 2 221 029601-015 CONN. RING, 14-16 Ø 3/8 1
24 013919-013 CLAMP 2 222 029825-002 DIODE, 3 AMP, 400 VOLT 6
25 014996-004 WASHER, 1/4 SAE FLAT 4 225 060214-099 WIRE 16 AWG 15 C0NN FT 18
*27 013283-002 CABLE MOUNT 6 226 029620-002 CONN. BUTT 16-14 3
*28 067758-099 NYLON HOSE GUARD 3 *Not Shown
30 067863-000 SWITCH MOUNT 1

Final Assembly
067351-001
Drawing 1 of 2

6-8 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Final Assembly
067351-001
Drawing 2 of 2

LX31/41 Electric/Bi-Energy Work Platform 6-9

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Final Assembly, LX31 Electric - Dual Deck
067435-001
ITEM PART NO DESCRIPTION QTY. ITEM PART NO DESCRIPTION QTY.

1 067374-000 BASIC ASSY 1 *28 067758-099 NYLON HOSE GUARD 3

2 067384-001 CONTROLLER ASSY 1 30 067863-000 SWITCH MOUNT 1
3 067536-000 CONTROL CABLE ASSY 1 31 067866-002 SLIDE OUT DECK -REAR 1
4 067361-030 DECAL-KIT 1 32 067373-003 SCISSOR GUARD 1
5 067383-000 HOSE-KIT 1 *33 015963-099 STRAP MATL 9
6 030841-300 GUARDRAIL 1 *34 015964-000 STRAP HEAD 9
7 067359-001 POWER MODULE 1 35 012865-099 WIRE LOOM 3/4 DIA 8
8 067360-007 CONTROL MODULE 1 201 068776-048 CABLE ASSY. X 48” (3/8 X 3/8 LUG) 2
9 067446-000 HYD SCHM. REF 202 068776-014 CABLE ASSY. X 165” (3/8 X 3/8 LUG) 2
10 067447-003 ELEC. SCHM. REF 204 068776-012 CABLE ASSY. X 150 (3/8 X 3/8 LUG) 2
11 067866-001 SLIDE-OUT DECK 1 206 010154-001 BATTERY TERM. COVER 10
12 067692-000 CLIP, CABLE RETAINER 4 210 068777-107 CABLE ASSY. X 107” (3/8 X 5/16 LUG) 2
15 011252-006 SCRW, 1/4-20 X 3/4 4 211 029452-099 WIRE, 16 GA. BLACK 5
16 011248-004 LOCKNUT, 1/4-20 UNC 5 216 029355-099 WIRE 16 GA BLK/RED 5
17 065373-006 MAGNET 4 217 029496-099 WIRE 16 GA 2 CON 16
18 065373-005 SWITCH 4 218 014914-001 CONN. MALE PUSH, 14-16 .25 2
19 067913-000 ALUM. SW. PAD 2 219 029931-003 CONN. FEM. PUSH, 14-16 .25 2
20 026551-005 RIVET 1/8 X 1/4 GRIP 16 220 029601-012 CONN. RING, 14-16 #8 8
21 029447-099 CABLE 3 COND. 16 GA. 10 FT 221 029601-015 CONN. RING, 14-16 Ø 3/8 1
22 029620-002 CONN. BUTT 16-14 GA. 13 222 029825-002 DIODE, 3 AMP, 400 VOLT 6
23 063497-001 MERCURY SWITCH 2 225 060214-099 WIRE 16 AWG 15 C0NN FT 18
24 013919-013 CLAMP 2 226 029620-002 CONN. BUTT 16-14 3
25 014996-004 WASHER 1/4 SAE FLAT 4 *Not Shown
*27 013283-002 CABLE MOUNT 6

Final Assembly
067435-001
Drawing 1 of 2

6-10 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Final Assembly
067435-001
Drawing 2 of 2

LX31/41 Electric/Bi-Energy Work Platform 6-11

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Final Assembly, LX31 Bi-Energy - Dual Deck
067370-001
ITEM PART NO DESCRIPTION QTY. ITEM PART NO DESCRIPTION QTY.

1 067374-000 BASIC ASSY 1 32 067373-000 SCISSOR GUARD 1

2 067384-000 CONTROLLER ASSY 1 *33 015963-099 STRAP MATL 9
3 067536-000 CONTROL CABLE ASSY 1 *34 015964-000 STRAP HEAD 9
4 067361-021 DECAL-KIT 1 35 012865-099 WIRE LOOM 3/4 DIA 8
5 067383-000 HOSE-KIT 1 201 068776-005 CABLE ASSY. X 60” (3/8 X 3/8 LUG) 1
6 030841-300 GUARDRAIL 1 202 068776-016 CABLE ASSY. X 192” (3/8 X 3/8 LUG) 1
7 067359-000 POWER MODULE 1 203 068776-004 CABLE ASSY. X 54” (3/8 X 3/8 LUG) 1
8 067360-006 CONTROL MODULE 1 204 068776-013 CABLE ASSY. X 156” (3/8 X 3/8 LUG) 1
9 067446-000 HYD SCHM. REF 205 068777-001 CABLE ASSY. X 41” (5/16 X 3/8 LUG) 1
10 067447-002 ELEC. SCHM. REF 206 068777-002 CABLE ASSY. X 47” (5/16 X 3/8 LUG) 1
11 067866-001 SLIDE-OUT DECK 1 207 068777-123 CABLE ASSY. X 123” (5/16 X 3/8 LUG) 2
12 067692-000 CLIP, CABLE RETAINER 4 208 068777-100 CABLE ASSY. X 100” (5/16 X 3/8 LUG) 1
15 011252-006 SCRW, 1/4-20 X 3/4 4 210 068777-107 CABLE ASSY. X 107” (3/8 X 5/16 LUG) 1
16 011248-004 LOCKNUT, 1/4-20 UNC 5 211 029452-099 WIRE, 16 GA. BLACK 5
17 065373-006 MAGNET 4 212 063956-006 CONNECTOR 1
18 065373-005 SWITCH 4 213 063956-010 CONNECTOR PIN 4
19 067913-000 ALUM. SW. PAD 2 216 029355-099 WIRE 16 GA BLK/RED 5
20 026551-005 RIVET 1/8 X 1/4 GRIP 16 217 029496-099 WIRE 16 GA 2 CON 16
21 029447-099 CABLE 3 COND. 16 GA. 10 FT 218 014914-001 CONN. MALE PUSH, 14-16 .25 2
22 029620-002 CONN. BUTT 16-14 GA. 13 219 029931-003 CONN. FEM. PUSH, 14-16 .25 2
23 063497-001 MERCURY SWITCH 2 220 029601-012 CONN. RING, 14-16 #8 8
24 013919-013 CLAMP 2 221 029601-015 CONN. RING, 14-16 Ø 3/8 1
25 014996-004 WASHER, 1/4 SAE FLAT 4 222 029825-002 DIODE, 3 AMP, 400 VOLT 6
*27 013283-002 CABLE MOUNT 6 225 060214-099 WIRE 16 AWG 15 C0NN FT 18
*28 067758-099 NYLON HOSE GUARD 3 226 029620-002 CONN. BUTT 16-14 3
30 067863-000 SWITCH MOUNT 1 *Not Shown
31 067866-002 SLIDE OUT DECK-REAR 1

Final Assembly
067370-001
Drawing 1 of 2

6-12 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Final Assembly
067370-001
Drawing 2 of 2

LX31/41 Electric/Bi-Energy Work Platform 6-13

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Final Assembly, LX41 Electric - Dual Deck
067436-001
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.

1 067375-000 BASIC ASSY 1 28 067758-099 NYLON HOSE GUARD 3

2 067384-001 CONTROLLER ASSY 1 30 067863-000 SWITCH MOUNT 1
3 067536-001 CONTROL CABLE ASSY 1 31 067866-002 SLIDE OUT DECK -REAR 1
4 067361-031 DECAL-KIT 1 32 067373-004 SCISSOR GUARD 1
5 067383-000 HOSE-KIT 1 *33 015963-099 STRAP MATL 9
6 030841-300 GUARDRAIL 1 *34 015694-000 STRAP HEAD 9
7 067359-001 POWER MODULE 1 35 012865-099 WIRE LOOM 3/4 DIA 8
8 067360-007 CONTROL MODULE 1 201 068776-048 CABLE ASSY. X 48” (3/8 X 3/8 LUG) 2
9 067446-000 HYD SCHM. REF 202 068776-014 CABLE ASSY. X 165” (3/8 X 3/8 LUG) 2
10 067447-003 ELEC. SCHM. REF 204 068776-012 CABLE ASSY. X 150 (3/8 X 3/8 LUG) 2
11 067866-001 SLIDE-OUT DECK 1 206 010154-001 BATTERY TERM. COVER 10
12 067692-000 CLIP, CABLE RETAINER 8 210 068777-107 CABLE ASSY. X 107” (3/8 X 5/16 LUG) 2
15 011252-006 SCRW, 1/4-20 X 3/4 4 211 029452-099 WIRE, 16 GA. BLACK 5
16 011248-004 LOCKNUT, 1/4-20 UNC 5 216 029355-099 WIRE 16 GA BLK/RED 5
17 065373-006 MAGNET 4 217 029496-099 WIRE 16 GA 2 CON 16
18 065373-005 SWITCH 4 218 014914-001 CONN. MALE PUSH, 14-16 .25 2
19 067913-000 ALUM. SW. PAD 2 219 029931-003 CONN. FEM. PUSH, 14-16 .25 2
20 026551-005 RIVET 1/8 X 1/4 GRIP 16 220 029601-012 CONN. RING, 14-16 #8 8
21 029447-099 CABLE 3 COND. 16 GA. 10 FT 221 029601-015 CONN. RING, 14-16 Ø 3/8 1
22 029620-002 CONN. BUTT 16-14 GA. 13 222 029825-002 DIODE, 3 AMP, 400 VOLT 6
23 063497-001 MERCURY SWITCH 2 225 060214-099 WIRE 16 AWG 15 C0NN FT 18
24 013919-013 CLAMP 2 226 029620-002 CONN. BUTT 16-14 3
25 014996-004 WASHER, 1/4 SAE FLAT 4 *Not Shown
27 013283-002 CABLE MOUNT 6

Final Assembly
067436-001
Drawing 1 of 2

6-14 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Final Assembly
067436-001
Drawing 2 of 2

LX31/41 Electric/Bi-Energy Work Platform 6-15

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Final Assembly, LX41 Bi-Energy - Dual Deck
067371-001
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.

1 067375-000 BASIC ASSY 1 32 067373-001 SCISSOR GUARD 1

2 067384-000 CONTROLLER ASSY 1 *33 015963-099 STRAP MATL 9
3 067536-001 CONTROL CABLE ASSY 1 *34 015964-000 STRAP HEAD 9
4 067361-022 DECAL-KIT 1 35 012865-099 WIRE LOOM 3/4 DIA 8
5 067383-000 HOSE-KIT 1 201 068776-005 CABLE ASSY. X 60” (3/8 X 3/8 LUG) 1
6 030841-300 GUARDRAIL 1 202 068776-016 CABLE ASSY. X 192” (3/8 X 3/8 LUG) 1
7 067359-000 POWER MODULE 1 203 068776-004 CABLE ASSY. X 54” (3/8 X 3/8 LUG) 1
8 067360-006 CONTROL MODULE 1 204 068776-013 CABLE ASSY. X 156” (3/8 X 3/8 LUG) 1
9 067446-000 HYD SCHM. REF 205 068777-001 CABLE ASSY. X 41” (5/16 X 3/8 LUG) 1
10 067447-002 ELEC. SCHM. REF 206 068777-002 CABLE ASSY. X 47” (5/16 X 3/8 LUG) 1
11 067866-001 SLIDE-OUT DECK 1 207 068777-123 CABLE ASSY. X 123” (5/16 X 3/8 LUG) 2
12 067692-000 CLIP, CABLE RETAINER 8 208 068777-100 CABLE ASSY. X 100” (5/16 X 3/8 LUG) 1
15 011252-006 SCRW, 1/4-20 X 3/4 4 210 068777-107 CABLE ASSY. X 107” (3/8 X 5/16 LUG) 1
16 011248-004 LOCKNUT, 1/4-20 UNC 5 211 029452-099 WIRE, 16 GA. BLACK 5
17 065373-006 MAGNET 4 212 063956-006 CONNECTOR 1
18 065373-005 SWITCH 4 213 063956-010 CONNECTOR PIN 4
19 067913-000 ALUM. SW. PAD 2 216 029355-099 WIRE 16 GA BLK/RED 5
20 026551-005 RIVET 1/8 X 1/4 GRIP 16 217 029496-099 WIRE 16 GA 2 CON 16
21 029447-099 CABLE 3 COND. 16 GA. 10 FT 218 014914-001 CONN. MALE PUSH, 14-16 .25 2
22 029620-002 CONN. BUTT 16-14 GA. 13 219 029931-003 CONN. FEM. PUSH, 14-16 .25 2
23 063497-001 MERCURY SWITCH 2 220 029601-012 CONN. RING, 14-16 #8 8
24 013919-013 CLAMP 2 221 029601-015 CONN. RING, 14-16 Ø 3/8 1
25 014996-004 WASHER, 1/4 SAE 4 222 029825-002 DIODE, 3 AMP, 400 VOLT 6
*27 013283-002 CABLE MOUNT 6 225 060214-099 WIRE 16 AWG 15 C0NN FT 18
*28 067758-099 NYLON HOSE GUARD 3 226 029620-002 CONN. BUTT 16-14 3
30 067863-000 SWITCH MOUNT 1 *Not Shown
31 067866-002 SLIDE OUT DECK -REAR 1

Final Assembly
067371-001
Drawing 1 of 2

6-16 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Final Assembly
067371-001
Drawing 2 of 2

LX31/41 Electric/Bi-Energy Work Platform 6-17

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Basic Assembly, LX31 Electric & Bi-Energy
067354-000
ITEM PART DESCRIPTION QTY.
1 067358-000 CHASSIS ASSEMBLY 1
2 067422-002 SCISSOR LINKAGE 1
3 067780-001 PLATFORM WELDMENT 1
4 067879-001 MOTOR COVER 2
5 011253-008 SCR H H C 5/16 X 1 8
6 067737-001 LADDER WELDMENT 1
7 067738-000 SLIDE BLOCK 6
8 067852-000 PIN 4
9 067853-000 PIN 2
10 014996-005 WASHER 5/16 DIA 8
11 066189-000 SPACER 1/4 4
12 067853-001 PIN 2
13 066189-004 SPACER 1/8 8
15 011256-012 SCREW HHC 1/2-13 X 1 1/2 4
16 011256-028 SCREW HHC 1/2-13 X 3 1/2 8
17 014033-032 SCREW HHC 1/2-13 X 4 GR8 8
20 011248-008 NUT 1/2-13 ESNA 16

6-18 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Basic Assembly
067354-000
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-19

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Basic Assembly, LX41Electric & Bi-Energy
067355-000
ITEM PART DESCRIPTION QTY.
1 067358-000 CHASSIS ASSEMBLY 1
2 067423-002 SCISSOR LINKAGE 1
3 067780-001 PLATFORM WELDMENT 1
4 067879-001 MOTOR COVER 2
5 011253-008 SCR HHC 5/16 X 1 8
6 067737-000 LADDER WELDMENT 1
7 067738-000 SLIDE BLOCK 6
8 067852-000 PIN 4
9 067853-000 PIN 2
10 014996-005 WASHER 5/16 DIA 8
11 066189-000 SPACER 1/4 4
12 067853-001 PIN 2
13 066189-004 SPACER 1/8 8
15 011256-012 SCREW HHC 1/2-13 X 1 1/2 4
16 011256-028 SCREW HHC 1/2-13 X 3 1/2 8
17 014033-032 SCREW HHC 1/2-13 X 4 8
20 011248-008 NUT 1/2-13 ESNA 16

6-20 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Basic Assembly
067355-000
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-21

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Basic Assembly, LX41Electric & Bi-Energy - Dual Deck
067374-000
ITEM PART DESCRIPTION QTY.
1 067358-000 CHASSIS ASSEMBLY 1
2 067423-002 SCISSOR LINKAGE 1
3 067780-001 PLATFORM WELDMENT 1
4 067879-001 MOTOR COVER 2
5 011253-008 SCR HHC 5/16 X 1 8
7 067738-000 SLIDE BLOCK 6
8 067852-000 PIN 4
9 067853-000 PIN 2
10 014996-005 WASHER 5/16 DIA 8
11 066189-000 SPACER 1/4 4
12 067853-001 PIN 2
13 066189-004 SPACER 1/8 8
16 011256-028 SCREW HHC 1/2-13 X 3 1/2 8
17 014033-032 SCREW HHC 1/2-13 X 4 8
20 011248-008 NUT 1/2-13 ESNA 16

6-22 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Basic Assembly
067374-000
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-23

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Basic Assembly, LX41Electric & Bi-Energy - Dual Deck
067375-000
ITEM PART DESCRIPTION QTY.
1 067358-000 CHASSIS ASSEMBLY 1
2 067423-002 SCISSOR LINKAGE 1
3 067780-001 PLATFORM WELDMENT 1
4 067879-001 MOTOR COVER 2
5 011253-008 SCR HHC 5/16 X 1 8
7 067738-000 SLIDE BLOCK 6
8 067852-000 PIN 4
9 067853-000 PIN 2
10 014996-005 WASHER 5/16 DIA 8
11 066189-000 SPACER 1/4 4
12 067853-001 PIN 2
13 066189-004 SPACER 1/8 8
16 011256-028 SCREW HHC 1/2-13 X 3 1/2 8
17 014033-032 SCREW HHC 1/2-13 X 4 8
20 011248-008 NUT 1/2-13 ESNA 16

6-24 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Basic Assembly
067375-000
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-25

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Chassis Assembly, LX31/41
067358-000
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.

1 067715-001 CHASSIS WELDMENT (FIXED AXLE) 1 35 067746-001 PIN STEERING LINK 2

2 067743-000 TRUNNION (L.H.) 1 36 011256-020 SCREW HHC 1/2-13 X 2 1/2 2
3 067742-000 TRUNNION (R.H.) 1 37 013315-011 RETAINING “E” RING 2
4 067739-000 STEERING LINK 1 38 062889-012 HAIRPIN COTTER 2
5 067812-000 BUSHING, STEERING 2 39 003495-000 FITTING ELBOW STREET 6MB-6FJ 2
6 067813-000 CONNECTING LINK 2 40 011469-005 LUG NUT 9/16-18 10
7 067746-000 TRUNNION PIN LOWER 2 41 011936-001 FITTING TEE 4MJ-4MJ-4MB 1
8 067833-000 SPINDLE WELDMENT 2 43 011934-003 FITTING, 6 MB - 4 MJ 90 DEGREES 2
9 067748-000 STEERING CLAMP 1 44 012030-010 SCREW SOC HD CAP 1/2-13 X 1 1/4 8
10 013336-003 GREASE FITTING 1/8” 4 45 011848-051 PIN CLEVIS 1 DIA. X 2 1
11 067816-000 PLATE WELDMENT 1 49 012030-032 SCREW SOC HD CAP 1/2-13 X 4 4
12 067613-000 HUB, 8 BOLT ON 8” B.C. 2 50 067746-002 PIN TRUNNION UPPER 2
13 068570-001 PLANTEARY DRIVE 2 51 068327-000 TIRE/WHEEL ASSY REAR 2
14 068569-000 BRAKE 2 52 011256-034 SCREW HHC 1/2-13 X 4 1/4 4
15 068573-000 MOTOR ELECTRIC 2 54 011238-012 WASHER SPLIT LOCK 3/4 4
16 067633-000 STEERING CYLINDER 1 55 064279-000 THRUST WASHER 2
* 067633-010 SEAL KIT - 56 011248-010 NUT 5/8-11 HEX ESNA 2
17 011252-020 SCREW HHC 1/4-20 X 2 1/2 4 57 067805-099 GROMMET MATL 7FT
19 011248-004 NUT 1/4-20 HEX ESNA 4 58 024501-003 SHEET 1/8 RUBBER 3 X 48 1
20 067606-020 BEARING, SCISSOR PIVOT 2 60 011934-001 FITTING 90 DEGREES 4MJ-4MJ 1
21 062642-020 BUSHING 160U16 4 61 011937-001 FITTING 90 DEGREES 4MJ-4FJ 1
22 062649-020 BEARING, STEERING ROD 2 62 REF COUPLING 2
23 067606-010 BEARING, 160X16 6 63 REF MOUTING PLATE 2
25 067665-004 TIRE & WHEEL ASSY FRONT 2 64 REF SCREW R.H. #2-56 X 1/4 6
26 011254-020 SCREW HHC 3/8-16 X 2 1/2 4 65 REF WASHER 6
27 011248-006 NUT 3/8-16 HEX ESNA 4 66 068551-001 TACH ASSY KIT (ITEMS 62-65) 2
28 011258-012 SCREW HHC 3/4-10 X 1 1/2 4 67 REF GASKET 4
29 011238-008 WASHER 1/2 SPLIT LOCK 29 68 067367-000 MOTOR COVER 2
30 011256-012 SCREW HHC 1/2-13 X 1 1/2 16 69 011468-020 STUD WHEEL 1/2-20 X 2 3/8 18
31 011257-028 SCREW HHC 5/8-11 X 3 1/2 2 70 011248-005 NUT HEX ESNA 5/16-18UNC 4
32 011247-008 NUT 1/2-20UNF HEX ESNA THIN 28 71 011240-005 WASHER 5/16 STD FLAT 4
33 011256-024 SCREW HHC 1/2-13 X 3 8 72 011239-008 WASHER ASTM 1/2 4
34 011848-050 PIN CLEVIS 1 X 2 3/4 1 *Not Shown

6-26 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Chassis Assembly
067358-000
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-27

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Scissor Linkage Assembly, LX31 Scissor Linkage Assembly, LX31
067422-001 Dual Deck
ITEM PART DESCRIPTION QTY. 067422-002
1 067550-001 ARM WELDMENT 1
ITEM PART DESCRIPTION QTY.
2 067551-001 ARM WELDMENT 1
3 067552-000 ARM WELDMENT 1 1 067550-001 ARM WELDMENT 1
4 067593-000 ARM WELDMENT 2 2 067551-003 ARM WELDMENT 1
5 067828-001 ARM WELDMENT 1 3 067552-000 ARM WELDMENT 1
6 067830-000 ARM WELDMENT 1 4 067593-001 ARM WELDMENT 2
7 067832-000 ARM WELDMENT 1 5 067828-001 ARM WELDMENT 1
8 011786-017 MACHINERY BUSHING, 2” ID X 14 GA. 1 6 067830-000 ARM WELDMENT 1
9 011757-028 COTTER PIN 3/8 DIA X 3 1/2 1 7 067832-000 ARM WELDMENT 1
10 067606-020 BEARING, 2” ID X 1 1/2” LG. 12 8 011786-017 MACHINERY BUSHING, 2” ID X 14 GA. 1
11 067606-030 BEARING, 3” ID X 1 1/2” LG. 16 9 011757-028 COTTER PIN 3/8 DIA X 3 1/2 1
12 067583-000 PIN WELDMENT 5 10 067606-020 BEARING, 2” ID X 1 1/2” LG. 12
13 067580-000 PIN WELDMENT 8 11 067606-030 BEARING, 3” ID X 1 1/2” LG. 16
14 067585-000 PIN WELDMENT 1 12 067583-000 PIN WELDMENT 5
15 067586-000 PIN, CYLINDER 2 13 067580-000 PIN WELDMENT 8
16 067635-000 LIFT CYLINDER 1 14 067585-000 PIN WELDMENT 1
* 067635-010 SEAL KIT - 15 067586-000 PIN, CYLINDER 2
17 014033-048 H.H.C.S. 1/2-13UNC X 6 GR. 8 8 16 067635-000 LIFT CYLINDER 1
18 014033-032 H.H.C.S. 1/2-13UNC X 4 GR. 8 6 * 067635-010 SEAL KIT -
19 011248-008 HEX LOCK NUT 1/2-13UNC 14 17 014033-048 H.H.C.S. 1/2-13UNC X 6 GR. 8 8
20 067591-000 SUPPORT WELDMENT 1 18 014033-032 H.H.C.S. 1/2-13UNC X 4 GR. 8 6
21 013336-001 GREASE FITTING 14 19 011248-008 HEX LOCK NUT 1/2-13UNC 14
22 011934-004 ADAPTER 90 DEGREES #6 1 20 067591-000 SUPPORT WELDMENT 1
23 063925-004 DOWN VALVE 1 21 013336-001 GREASE FITTING 14
24 003570-001 RETAINING PIN ASSY 1 22 011934-004 ADAPTER 90 DEGREES #6 1
25 067659-000 CABLE ASSY 1 23 063925-004 DOWN VALVE 1
26 067877-000 COUPLER 1 24 003570-001 RETAINING PIN ASSY 1
27 015919-003 ORIFICE PLATE 1 25 067659-000 CABLE ASSY 1
28 005133-000 SPRING 1 26 067877-000 COUPLER 1
*Not Shown 27 015919-003 ORIFICE PLATE 1
28 005133-000 SPRING 1
*Not Shown

6-28 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Scissor Linkage Assembly

067422-001
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-29

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Scissor Linkage Assembly, LX41 Scissor Linkage Assembly, LX41
067423-001 Dual Deck
ITEM PART DESCRIPTION QTY. 067423-002
1 067550-001 ARM WELDMENT 1
ITEM PART DESCRIPTION QTY.
2 067551-001 ARM WELDMENT 1
3 067552-000 ARM WELDMENT 1 1 067550-001 ARM WELDMENT 1
4 067593-000 ARM WELDMENT 2 2 067551-003 ARM WELDMENT 1
5 067553-001 ARM WELDMENT 1 3 067552-000 ARM WELDMENT 1
6 067554-000 ARM WELDMENT 2 4 067593-001 ARM WELDMENT 2
7 067555-000 ARM WELDMENT 1 5 067553-001 ARM WELDMENT 1
8 067556-000 ARM WELDMENT 1 6 067554-000 ARM WELDMENT 2
9 067557-000 ARM WELDMENT 1 7 067555-000 ARM WELDMENT 1
10 067606-020 BEARING, 2” ID X 1 1/2” LG. 28 8 067556-000 ARM WELDMENT 1
11 067606-030 BEARING, 3” ID X 1 1/2” LG. 16 9 067557-000 ARM WELDMENT 1
12 067583-000 PIN WELDMENT 11 10 067606-020 BEARING, 2” ID X 1 1/2” LG. 28
13 067580-000 PIN WELDMENT 8 11 067606-030 BEARING, 3” ID X 1 1/2” LG. 16
14 067585-000 PIN WELDMENT 1 12 067583-000 PIN WELDMENT 11
15 067586-000 PIN, CYLINDER 2 13 067580-000 PIN WELDMENT 8
16 067635-000 LIFT CYLINDER 1 14 067585-000 PIN WELDMENT 1
* 067635-010 SEAL KIT - 15 067586-000 PIN, CYLINDER 2
17 014033-048 H.H.C.S. 1/2-13UNC X 7 1/2 GR. 8 8 16 067635-000 LIFT CYLINDER 1
18 014033-032 H.H.C.S. 1/2-13UNC X 4 1/2 GR. 8 12 * 067635-010 SEAL KIT -
19 011248-008 HEX LOCK NUT 1/2-13UNC 20 17 014033-048 H.H.C.S. 1/2-13UNC X 7 1/2 GR. 8 8
20 067591-000 SUPPORT WELDMENT 1 18 014033-032 H.H.C.S. 1/2-13UNC X 4 1/2 GR. 8 12
21 013336-001 GREASE FITTING 20 19 011248-008 HEX LOCK NUT 1/2-13UNC 20
22 011941-005 STRAIGHT ADAPTER #6 1 20 067591-000 SUPPORT WELDMENT 1
23 063925-004 DOWN VALVE 1 21 013336-001 GREASE FITTING 20
24 003570-001 RETAINING PIN ASSY 1 22 011941-005 STRAIGHT ADAPTER #6 1
25 065754-004 CABLE ASSY 1 23 063925-004 DOWN VALVE 1
26 067877-000 COUPLER 1 24 003570-001 RETAINING PIN ASSY 1
27 015919-003 ORIFICE PLATE 1 25 065754-004 CABLE ASSY 1
28 005133-000 SPRING 1 26 067877-000 COUPLER 1
29 011786-017 MACHINERY BUSHING, 2” ID X 14 GA. 1 27 015919-003 ORIFICE PLATE 1
30 011757-028 COTTER PIN 3/8 DIA X 3 1/2 1 28 005133-000 SPRING 1
*Not Shown 29 011786-017 MACHINERY BUSHING, 2” ID X 14 GA. 1
30 011757-028 COTTER PIN 3/8 DIA X 3 1/2 1
*Not Shown

6-30 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Scissor Linkage Assembly

067423-001
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-31

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Power Module Assembly, LX31/41 Electric
067359-001
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.

1 067809-001 HINGE, 2 X 71 1 38 021305-007 PLUG, MAGNETIC 1

2 067811-001 POWER MODULE WELDMENT 1 40 068712-002 BRACKET 1
3 067800-002 MODULE DOOR, R.H. 1 41 066516-004 PLUG 4” 1
4 067801-002 MODULE DOOR, L.H. 1 42 010150-005 FITTING BULKHEAD 1
5 067799-004 MODULE COVER 1 43 011979-008 O-RING 1
6 067808-000 HINGE, 2 X 22 2 44 068565-000 ACCUMULATOR 1
7 026554-002 POP RIVET, 1/4 DIA. (.251-.375 GRIP) 56 45 011252-006 SCREW HHC 1/4-20 X 3/4 2
8 005299-000 LATCH, TOGGLE 2 47 020733-002 FITTING TEE 6FJX-6MJ-6MJ 1
9 067629-000 LATCH, FLUSH LIFT & TURN 2 49 063979-006 GAGE, LUBE SIGHT 1
12 014923-007 FITTING 16MP-12FP 1 50 011248-004 NUT HEX ESNA 1/4-20 6
13 063935-000 SUCTION SCREEN 1 51 013487-010 FITTING STR 12MP-12MP 1
14 067841-000 TANK, HYDRAULIC 1 52 011941-010 FITTING 90 6MP-6MJ 1
15 067388-000 POWER UNIT 2 53 011253-007 SCREW HHC 5/16-18 X 7/8 8
16 025427-002 HANDLE 2 54 011240-005 WASHER 5/16 FLAT STD 8
17 026533-002 RIVET POP, 3/160 (.126-.250 GRIP) 8 55 011937-003 FITTING 90 6FJX-6MJ 3
18 067856-001 STIFFENER BAR 1 56 011250-005 NUT HEX 5/16-18 8
19 011708-004 SCREW RD HD 8-32 X 1/2 4 57 011982-008 FITTING TEE 8MP-8FP-8FP 1
20 011248-002 NUT HEX 8-32 ESNA 4 58 013969-002 FITTING 4MJ-8FJ 1
21 011254-002 SCREW HHC 3/8-16 X 3/4 4 59 011939-014 FITTING 8MP-6MJ 1
22 064039-001 HYDRAULIC TANK MOUNTING TAB 1 60 021305-006 FITTING PLUG 2
23 067624-000 HYDRAULIC FILTER 1 61 011939-018 FITTING STR 12MP-6MJ 1
* 067624-010 HYDRAULIC FILTER ELEMENT - 62 063029-000 BUSS BAR 2
24 063931-016 ELBOW 90 DEGREES 1 63 067765-000 TUBE EXTENSION 1
25 067854-000 ANGLE RES. MOUNT 1 64 067799-003 COVER 1
26 011240-006 WASHER 3/8 FLAT STD 8 65 067799-004 COVER 1
28 011248-006 NUT HEX 3/8-16 ESNA 7 66 063947-008 NUT HEX ESNA M8 2
29 067389-000 VALVE BLOCK 1 67 011275-006 SCREW HHC #10 X 3/4 4
30 068324-002 BRAKE VALVE ASSY 1 68 011240-003 WASHER #10 STD FLAT 8
31 011934-004 FITTING EL 6MP-6MJ 1 69 011249-003 NUT HHC ESNA #10 4
32 015961-006 FITTING TEE 6MP-6MJ 1 71 011941-005 FITTING 6MB-6MJ 2
33 011939-024 FITTING 16MP-16MJ 1 72 011941-010 FITTING 8MB-8MJ 3
34 015959-004 FITTING 12FJX-8MB 2 73 014280-002 FITTING 6MB-4FB 1
35 011939-022 FITTING STR 12MJ-16MP 1 74 063965-001 FITTING CONNECTOR GAGE 2
36 011982-004 FITTING TEE 12MP-12FP-12FP 1 75 067377-000 MOTOR SPACER 3
37 063930-001 BREATHER/FILLER CAP 1 77 068776-016 CABLE ASSY X 16 (3/8 X 3/8 LUG) 2

6-32 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Power Module Assembly

067359-001
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-33

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Power Module Assembly, LX31/41 Bi-Energy
067359-000
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.

1 067809-001 HINGE, 2 X 71 1 40 068712-002 BRACKET 1

2 067811-001 POWER MODULE WELDMENT 1 41 010070-099 SEAL STRIP GASKET FT. 1.62
3 067800-002 MODULE DOOR, R.H. 1 42 010150-005 FITTING BULKHEAD 8MJ-8MJ 1
4 067801-002 MODULE DOOR, L.H. 1 43 011979-008 O-RING 1
5 067799-004 MODULE COVER 1 44 068565-000 ACCUMULATOR 1
6 067808-000 HINGE, 2 X 22 2 45 011252-006 SCREW HHC 1/4-20 X 3/4 5
7 026554-002 POP RIVET, 1/4 DIA. (.251 - .375 GRIP) 56 46 011240-004 WASHER FLAT STD 1/4 4
8 005299-000 LATCH, TOGGLE 2 47 020733-002 FITTING TEE 6FJX-6MJ-6MJ 1
9 067629-000 LATCH, FLUSH LIFT & TURN 2 48 013259-006 CLAMP, MUFFLER 1-1/2” 2
10 067391-000 ENGINE ASSY 1 49 063979-006 GAGE, LUBE SIGHT 1
11 013259-007 CLAMP 1 50 011248-004 NUT HEX ESNA 1/4-20 7
12 014923-007 FITTING 16MP-6FP 1 51 013487-010 FITTING STR 12MP-12MP 1
13 063935-000 SUCTION SCREEN 1 52 011940-010 FITTING 90 6MP-6MJ 1
14 067841-000 TANK, HYDRAULIC 1 53 011253-007 SCREW HHC 5/16-18 X 7/8 8
15 067388-000 POWER UNIT 2 54 011240-005 WASHER 5/16 FLAT STD 8
16 025427-002 HANDLE 2 55 011937-003 FITTING 90 6FJX-6MJ 3
17 026533-002 RIVET POP, 3/16D .126 -.250 GRIP 8 56 011250-005 NUT HEX 5/16-18 8
18 067856-001 STIFFENER BAR 1 57 011982-008 FITTING TEE 8MP-8FP-8FP 1
19 011708-004 SCREW RD HD 8-32 X 1/2 4 58 013969-002 FITTING 4MJ-8MFJ 1
20 011248-002 NUT HEX 8-32 ESNA 4 59 011939-014 FITTING 8MP-6MJ 1
21 011254-006 SCREW HHC 3/8-16 X 3/4 4 60 021305-006 FITTING PLUG 2
22 064039-001 HYDRAULIC TANK MOUNTING TAB 1 61 067691-002 SNORKEL WELDMENT 1
23 067624-000 HYDRAULIC FILTER 1 62 063947-008 NUT HEX ESNA M8 2
24 063931-016 ELBOW 90° 1 63 067765-000 TUBE EXTENSION 1
25 067854-000 ANGLE RES. MOUNT 1 64 067799-003 COVER 1
26 011240-006 WASHER 3/8 FLAT STD 14 65 067799-004 COVER 1
27 011254-008 SCREW HHC 3/8-16 X 1 3 66 068823-000 OVERFLOW KIT 1
28 011248-006 NUT HEX 3/8-16 ESNA 7 67 011275-006 SCREW HHC #10 X 3/4 4
29 067389-000 VALVE BLOCK 1 68 011240-003 WSHER #10 STD FLAT 8
30 068324-002 BRAKE VALVE ASSY 1 69 011249-003 NUT HHC ESNA #10 4
31 011934-004 FITTING EL 6MP-6MJ 1 70 063936-027 GASKET MUFFLER 1
32 015961-006 FITTING TEE 6MP-6MJ 1 71 011941-005 FITTING 6MB-6MJ 2
33 011939-024 FITTING 16MP-16MJ 1 72 011941-010 FITTING 8MB-8MJ 3
34 015959-004 FITTING 12FJX-8MB 2 73 014280-002 FITTING 6MB-4FB 1
35 011939-022 FITTING STR 12MJ-16MP 1 74 063965-001 FITTING CONNECTOR GAGE 2
36 011982-004 FITTING TEE 12MP-12FP-12FP 1 75 067377-000 MOTOR SPACER 3
37 063930-001 BREATHER/FILLER CAP 1 76 100209-001 SHOCK ISOLATER 4
38 021305-007 PLUG, MAGNETIC 1 77 068776-007 CABEL ASSY X 16 (3/8 X 3/8 LUG) 2
39 067393-000 EXHAUST TUBE 1 78 013919-006 CLAMP CABLE 2

6-34 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Power Module Assembly

067359-000
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-35

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Engine Assembly, LX31/41 Bi-Energy
067391-000
ITEM PART DESCRIPTION QTY.
1 067390-000 MOTOR MOUNT WELDMENT 1
2 068951-001 ENGINE ASSY 1
3 068933-002 GENERATOR ADJUSTING STRAP 1
4 068933-000 GENERATOR 1
5 068947-001 SPROCKET 38 TOOTH 1
6 014806-008 BUSHING 7/8” SH 1
7 068947-000 SPROCKET 64 TOOTH 1
8 014806-009 BUSHING 1 7/16 SK 1
9 068948-000 BELT HTD DRIVE 1
10 063936-024 GASKET MUFFLER 1
11 067394-000 EXHAUST TUBE WELDMENT 1
15 011240-008 WASHER 1/2 STD FLAT 8
16 011256-010 SCREW HHC 1/2-13UNC X 1 1/4 4
17 011256-012 SCREW HHC 1/2-13UNC X 1 1/2 2
18 011256-044 SCREW HHC 1/2-13UNC X 5 1/2 1
19 011248-008 NUT HEX ESNA 1/2-13UNC 2
21 011240-004 WASHER 1/4 STD FLAT 4
22 011238-004 WASHER 1/4 SPLIT LOCK 4
23 011250-004 NUT HEX 1/4-20UNC 4
24 011252-008 SCRWE HHC 1/4-20UNC X 1 4

6-36 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Engine Assembly
067391-000
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-37

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Control Module Assembly, LX31/41 Bi-Energy
067360-004
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.

1 067810-001 CONTROL MODULE WELDMENT 1 47 068334-010 BATTERY CABLE ASSY X 10 5

2 067362-002 CONTROL BOX ASSY BI ENERGY EURO 1 48 068332-004 BATTERY CABLE ASSY 1
3 067485-001 FUEL TANK ASS’Y, DIESEL 1 49 068574-001 CHARGER 1
4 012736-099 HOSE, 3/16 I.D. 11 FT 50 068332-003 BATTERY CABLE ASSY 1
5 067399-000 BATTERY DIVIDER 1 51 067366-000 BATTERY CHARGER BRACKET 1
6 011239-006 3/8 SPLIT LOCKWASHER 2 52 067368-000 RELAY COVER 1
7 067629-000 LATCH, FLUSH LIFT & TURN 2 53 011252-012 SCREW HHC 1/4-20UNC X 1 1/2 4
8 005299-000 LATCH, TOGGLE 2 54 068332-005 CABLE ASSY 1
9 068489-001 CONTROL MOUNT 1 55 029902-002 CONNECTER HANDLE 1
10 063947-008 NUT HEX ESNA M8 2 56 029980-000 CONNECTOR 50 AMP 1
11 011240-004 WASHER 1/4 FLAT 30 57 067338-000 RELAY COVER 1
12 067387-000 RELAY PANEL ASSY 1 58 062786-004 SCREW SELF TAP #10 3
13 012739-099 HOSE, 1/4 I.D. 11 FT 59 068334-014 CABLE ASSY X 14 2
15 020541-001 HOSE CLAMP 3 60 067386-000 BATTERY TRAY 1
16 011254-008 SCRW HHC GR5 3/8-16UNC X 1 6 101 067387-006 SPACER 2
17 011708-004 SCRW MACH RD HD 8-32UNC X 1/2 4 102 067387-007 CONTACTOR MOUNTING BRACKET 1
18 011248-002 LOCK NUT, ESMA 8-32UNC 4 *103 067387-008 INSULATING SHEET 1
19 064040-000 ANGLE, BATTERY HOLD DOWN 1 *104 067387-009 HARNESS ASSEMBLY 1
20 062299-002 BATTERY, 12 VDC GROUP-27C 1 *105 067387-010 CABLE ASSEMBLY, 9” 1
21 029945-013 LEVEL SENSOR 1 *106 067387-011 CABLE ASSEMBLY, 14” 1
22 012039-000 ROD, BATTERY HOLD DOWN 2 *107 067367-012 CABLE ASSEMBLY, 17” 1
24 067799-005 MODULE COVER 1 *108 067387-013 CABLE ASSEMBLY, 18” 1
25 067808-000 HINGE, 1 1/2 X 23 7/8 2 *109 067387-014 CABLE ASSEMBLY, 22” 1
26 067809-001 HINGE, 1 1/2 1 110 067387-005 MOS90 “D” CONTROLLER 1
27 067799-003 MODULE COVER / CONTROL 1 111 067387-015 PC BOARD ASSEMBLY 1
28 067800-003 MODULE DOOR, R.H. 1 112 067387-016 RESISTOR BRACKET ASSEMBLY 1
29 067801-003 MODULE DOOR, L.H. 1 113 067387-017 TACHOMETER BRACKET ASSEMBLY 1
30 026554-002 POP RIVET, 1/4 DIA (.251-.375 GRIP) 60 114 067387-018 SUPRESSION ASSEMBLY 1
31 011248-006 NUT, 3/8-16 ESNA 6 115 067387-019 TERMINAL SUB ASSEMBLY 3
32 011252-006 SCREW, HHC 1/4-20 X 3/4 25 116 067387-020 PUMP OVERRIDE CONTACTOR, SW200-673 1
33 011248-004 NUT, 1/4-20 ESNA 38 117 068552-000 PUMP TRACTION CONTACTOR, SW201-179 1
34 025427-002 HANDLE 2 118 068552-001 REV/FWD CONTACTOR, SW202-221 2
35 067854-001 ANGLE, FUEL TANK MOUNT 1 119 068550-013 CONTACTOR BUSSBAR 2
36 067856-001 WELDMENT, STIFFENER 1 120 067387-021 CONTACTOR BUSSBAR 1
37 011254-006 SCREW HHC 3/8-16 X 3/4 4 121 067387-022 FUSE, 300 AMP 2
38 011248-005 NUT HEX ESNA 5/16-18 2 122 067387-023 RELAY, 48V 10A 1
39 011240-005 WASHER 5/16 STD FLAT 16 207 068777-003 CABLE ASSY. X 25” (5/16 X 3/8 LUG) 1
40 011253-007 SCREW HHC 5/16-18UNC X 7/8 16 208 068777-004 CABLE ASSY. X 20” (5/16 X 3/8 LUG) 1
41 014025-005 NUT HEX CENTERLOCK 5/16-18UNC 16 211 029452-099 WIRE, 16 GA. BLACK 5
42 011821-004 SCREW BUTT HD. 1/4-20UNC X 1/2 4 218 014914-001 CONN. MALE PUSH, 14-16 .25 3
43 011240-006 WASHER 3/8 STD FLAT 12 219 029931-003 CONN. FEM. PUSH, 14-16 .25 3
44 064462-014 PLUG HOLE 1 221 029601-015 CONN. RING, 14-16 Ø 3/8 1
45 067396-000 BATTERY SUPPORT 3 223 029440-099 CABLE, 12 GA. 3 COND. S.O REF
46 068568-000 BATTERY 8 *Not Shown

Control Module Assembly

067360-004
Drawing 1 of 3

6-38 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Control Module Assembly

067360-004
Drawing 2 of 3

LX31/41 Electric/Bi-Energy Work Platform 6-39

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN

Control Module Assembly

067360-004
Drawing 3 of 3

6-40 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1
Control Module Assembly, LX31/41 Electric
067360-005
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.
51 067366-000 BATTERY CHARGER BRACKET 1
1 067810-001 CONTROL MODULE WELDMENT 1 52 067368-000 RELAY COVER 1
2 067362-003 CONTROL BOX ASSY BI ENERGY DOM 1 53 011252-012 SCREW HHC 1/4-20UNC X 1 1/2 4
5 067399-000 BATTERY DIVIDER 1 54 068332-005 CABLE ASSY 1
7 067629-000 LATCH, FLUSH LIFT & TURN 2 55 029902-002 CONNECTER HANDLE 1
8 005299-000 LATCH, TOGGLE 2 56 029980-000 CONNECTOR 50 AMP 1
9 068489-001 CONTROL MOUNT 1 57 067338-000 RELAY COVER 1
10 063947-008 NUT HEX ESNA M8 2 58 062786-004 SCREW SELF TAP #10 3
11 011240-004 WASHER 1/4 FLAT 30 59 068334-014 CABLE ASSY X 14 2
12 067387-000 RELAY PANEL ASSY 1 101 067387-006 SPACER 2
16 011254-008 SCRW HHC GR5 3/8-16UNC X 1 2 102 067387-007 CONTACTOR MOUNTING BRACKET 1
17 011708-004 SCRW MACH RD HD 8-32UNC X 1/2 4 *103 067387-008 INSULATING SHEET 1
18 011248-002 LOCK NUT, ESMA 8-32UNC 4 *104 067387-009 HARNESS ASSEMBLY 1
21 029945-013 LEVEL SENSOR 1 *105 067387-010 CABLE ASSEMBLY, 9” 1
24 067799-005 MODULE COVER 1 *106 067387-011 CABLE ASSEMBLY, 14” 1
25 067808-000 HINGE, 1 1/2 X 23 7/8 2 *107 067367-012 CABLE ASSEMBLY, 17” 1
26 067809-001 HINGE, 1 1/2 1 *108 067387-013 CABLE ASSEMBLY, 18” 1
27 067799-003 MODULE COVER / CONTROL 1 *109 067387-014 CABLE ASSEMBLY, 22” 1
28 067800-003 MODULE DOOR, R.H. 1 110 067387-005 MOS90 “D” CONTROLLER 1
29 067801-003 MODULE DOOR, L.H. 1 111 067387-015 PC BOARD ASSEMBLY 1
30 026554-002 POP RIVET, 1/4 DIA (.251-.375 GRIP) 60 112 067387-016 RESISTOR BRACKET ASSEMBLY 1
31 011248-006 NUT, 3/8-16 ESNA 4 113 067387-017 TACHOMETER BRACKET ASSEMBLY 1
32 011252-006 SCREW, HHC 1/4-20 X 3/4 25 114 067387-018 SUPRESSION ASSEMBLY 1
33 011248-004 NUT, 1/4-20 ESNA 38 115 067387-019 TERMINAL SUB ASSEMBLY 3
34 025427-002 HANDLE 2 116 067387-020 PUMP OVERRIDE CONTACTOR, SW200-673 1
36 067856-001 WELDMENT, STIFFENER 1 117 068552-000 PUMP TRACTION CONTACTOR, SW201-179 1
37 011254-006 SCREW HHC 3/8-16 X 3/4 2 118 068552-001 REV/FWD CONTACTOR, SW202-221 2
39 011240-005 WASHER 5/16 STD FLAT 16 119 068550-013 CONTACTOR BUSSBAR 2
40 011253-007 SCREW HHC 5/16-18UNC X 7/8 16 120 067387-021 CONTACTOR BUSSBAR 1
41 014025-005 NUT HEX CENTERLOCK 5/16-18UNC 16 121 067387-022 FUSE, 300 AMP 2
42 011821-004 SCREW BUTT HD. 1/4-20UNC X 1/2 4 122 067387-023 RELAY, 48V 10A 1
43 011240-006 WASHER 3/8 STD FLAT 10 207 068777-003 CABLE ASSY. X 25” (5/16 X 3/8 LUG) REF
44 064462-014 PLUG HOLE 1 208 068777-004 CABLE ASSY. X 20” (5/16 X 3/8 LUG) REF
45 067396-000 BATTERY SUPPORT 3 211 029452-099 WIRE, 16 GA. BLACK 5
46 068568-000 BATTERY 8 218 014914-001 CONN. MALE PUSH, 14-16 .25 3
47 068334-010 BATTERY CABLE ASSY X 10 5 219 029931-003 CONN. FEM. PUSH, 14-16 .25 3
48 068332-004 BATTERY CABLE ASSY 1 221 029601-015 CONN. RING, 14-16 Ø 3/8 1
49 068574-001 CHARGER 1 223 029440-099 CABLE, 12 GA. 3 COND. S.O REF
50 068332-003 BATTERY CABLE ASSY 1 *NOT SHOWN

Control Module Assembly

067360-004
Drawing 1 of 3

LX31/41 Electric/Bi-Energy Work Platform 6-41

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN

Control Module Assembly

067360-005
Drawing 2 of 3

6-42 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Control Module Assembly

067360-005
Drawing 3 of 3

LX31/41 Electric/Bi-Energy Work Platform 6-43

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Control Module Assembly, LX31/41 Bi-Energy - Dual Deck
067360-006
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.

1 067810-001 CONTROL MODULE WELDMENT 1 50 068332-003 BATTERY CABLE ASSY 1

2 067362-003 CONTROL BOX ASSY BI ENERGY EURO 1 51 067366-000 BATTERY CHARGER BRACKET 1
3 067485-001 FUEL TANK ASS’Y, DIESEL 1 52 067368-000 RELAY COVER 1
4 012736-099 HOSE, 3/16 I.D. 11 FT 53 011252-012 SCREW HHC 1/4-20UNC X 1 1/2 4
6 011239-006 3/8 SPLIT LOCKWASHER 2 54 068332-005 CABLE ASSY 1
7 067629-000 LATCH, FLUSH LIFT & TURN 2 55 029902-002 CONNECTER HANDLE 1
8 005299-000 LATCH, TOGGLE 2 56 029980-000 CONNECTOR 50 AMP 1
9 068489-001 CONTROL MOUNT 1 57 067338-001 RELAY COVER 1
10 063947-008 NUT HEX ESNA M8 2 58 062786-004 SCREW SELF TAP #10 3
11 011240-004 WASHER 1/4 FLAT 26 59 068334-014 CABLE ASSY X 14 2
12 067387-000 RELAY PANEL ASSY 1 61 063650-012 GAS SPRING 1
13 012739-099 HOSE, 1/4 I.D. 11 FT 62 067495-000 GAS SPRING BRACKET 1
15 020541-001 HOSE CLAMP 3 63 015936-004 SCREW SCOULDER 3/8 X 1/2 2
16 011254-008 SCRW HHC GR5 3/8-16UNC X 1 6 64 067902-000 BRACKET GAS SPRING 1
17 011708-004 SCRW MACH RD HD 8-32UNC X 1/2 4 65 011253-008 SCREW HHC 5/16-18 UNC X 1 4
18 011248-002 LOCK NUT, ESMA 8-32UNC 4 101 067387-006 SPACER 2
19 064040-000 ANGLE, BATTERY HOLD DOWN 1 102 067387-007 CONTACTOR MOUNTING BRACKET 1
20 062299-002 BATTERY, 12 VDC GROUP-27C 1 *103 067387-008 INSULATING SHEET 1
21 029945-013 LEVEL SENSOR 1 *104 067387-009 HARNESS ASSEMBLY 1
22 012039-000 ROD, BATTERY HOLD DOWN 2 *105 067387-010 CABLE ASSEMBLY, 9” 1
24 067799-005 MODULE COVER 1 *106 067387-011 CABLE ASSEMBLY, 14” 1
25 067808-000 HINGE, 1 1/2 X 23 7/8 2 *107 067367-012 CABLE ASSEMBLY, 17” 1
26 067809-001 HINGE, 1 1/2 1 *108 067387-013 CABLE ASSEMBLY, 18” 1
27 067799-003 MODULE COVER / CONTROL 1 *109 067387-014 CABLE ASSEMBLY, 22” 1
28 067800-005 MODULE DOOR, R.H. 1 110 067387-005 MOS90 “D” CONTROLLER 1
29 067800-004 MODULE DOOR, L.H. 1 111 067387-015 PC BOARD ASSEMBLY 1
30 026554-002 POP RIVET, 1/4 DIA (.251-.375 GRIP) 60 112 067387-016 RESISTOR BRACKET ASSEMBLY 1
31 011248-006 NUT, 3/8-16 ESNA 6 113 067387-017 TACHOMETER BRACKET ASSEMBLY 1
32 011252-006 SCREW, HHC 1/4-20 X 3/4 23 114 067387-018 SUPRESSION ASSEMBLY 1
33 011248-004 NUT, 1/4-20 ESNA 38 115 067387-019 TERMINAL SUB ASSEMBLY 3
34 025427-002 HANDLE 2 116 067387-020 PUMP OVERRIDE CONTACTOR, SW200-673 1
35 067854-001 ANGLE, FUEL TANK MOUNT 1 117 068552-000 PUMP TRACTION CONTACTOR, SW201-179 1
36 067349-001 STAIR WELDMENT 1 118 068552-001 REV/FWD CONTACTOR, SW202-221 2
37 011254-006 SCREW HHC 3/8-16 X 3/4 2 119 068550-013 CONTACTOR BUSSBAR 2
38 011248-005 NUT HEX ESNA 5/16-18 UNC 6 120 067387-021 CONTACTOR BUSSBAR 1
39 011240-005 WASHER 5/16 STD FLAT 16 121 067387-022 FUSE, 300 AMP 2
40 011253-007 SCREW HHC 5/16-18UNC X 7/8 16 122 067387-023 RELAY, 48V 10A 1
41 014025-005 NUT HEX CENTERLOCK 5/16-18UNC 16 207 068777-003 CABLE ASSY. X 25” (5/16 X 3/8 LUG) REF
42 011821-004 SCREW BUTT HD. 1/4-20UNC X 1/2 4 208 068777-004 CABLE ASSY. X 20” (5/16 X 3/8 LUG) REF
43 011240-006 WASHER 3/8 STD FLAT 12 211 029452-099 WIRE, 16 GA. BLACK 5
44 064462-014 PLUG HOLE 1 218 014914-001 CONN. MALE PUSH, 14-16 .25 3
45 067396-000 BATTERY SUPPORT 3 219 029931-003 CONN. FEM. PUSH, 14-16 .25 3
46 068568-000 BATTERY 8 221 029601-015 CONN. RING, 14-16 Ø 3/8 1
47 068334-010 BATTERY CABLE ASSY X 10 5 223 029440-099 CABLE, 12 GA. 3 COND. S.O REF
48 068332-004 BATTERY CABLE ASSY 1 *NOT SHOWN
49 068574-001 CHARGER 1

Control Module Assembly

067360-006
Drawing 1 of 3

6-44 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Control Module Assembly

067360-006
Drawing 2 of 3

LX31/41 Electric/Bi-Energy Work Platform 6-45

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN

Control Module Assembly

067360-006
Drawing 3 of 3

6-46 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1
Control Module Assembly, LX31/41 Electric - Dual Deck
067360-007
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.

1 067810-001 CONTROL MODULE WELDMENT 1 54 068332-005 CABLE ASSY 1

2 067362-002 CONTROL BOX ASSY BI ENERGY EURO 1 55 029902-002 CONNECTER HANDLE 1
7 067629-000 LATCH, FLUSH LIFT & TURN 2 56 029980-000 CONNECTOR 50 AMP 1
8 005299-000 LATCH, TOGGLE 2 57 067338-001 RELAY COVER 1
9 068489-001 CONTROL MOUNT 1 58 062786-004 SCREW SELF TAP #10 3
10 063947-008 NUT HEX ESNA M8 2 59 068334-014 CABLE ASSY X 14 2
11 011240-004 WASHER 1/4 FLAT 30 61 063650-012 GAS SPRING 1
12 067387-000 RELAY PANEL ASSY 1 62 067495-000 GAS SPRING BRACKET 1
16 011254-008 SCRW HHC GR5 3/8-16UNC X 1 2 63 015936-004 SCREW SCOULDER 3/8 X 1/2 2
17 011708-004 SCRW MACH RD HD 8-32UNC X 1/2 4 64 067902-000 BRACKET GAS SPRING 1
18 011248-002 LOCK NUT, ESMA 8-32UNC 4 65 011253-008 SCREW HHC 5/16-18 UNC X 1 4
21 029945-013 LEVEL SENSOR 1 101 067387-006 SPACER 2
24 067799-005 MODULE COVER 1 102 067387-007 CONTACTOR MOUNTING BRACKET 1
25 067808-000 HINGE, 1 1/2 X 23 7/8 2 *103 067387-008 INSULATING SHEET 1
26 067809-001 HINGE, 1 1/2 1 *104 067387-009 HARNESS ASSEMBLY 1
27 067799-003 MODULE COVER / CONTROL 1 *105 067387-010 CABLE ASSEMBLY, 9” 1
28 067800-005 MODULE DOOR, R.H. 1 *106 067387-011 CABLE ASSEMBLY, 14” 1
29 067800-004 MODULE DOOR, L.H. 1 *107 067367-012 CABLE ASSEMBLY, 17” 1
30 026554-002 POP RIVET, 1/4 DIA (.251-.375 GRIP) 60 *108 067387-013 CABLE ASSEMBLY, 18” 1
31 011248-006 NUT, 3/8-16 ESNA 4 *109 067387-014 CABLE ASSEMBLY, 22” 1
32 011252-006 SCREW, HHC 1/4-20 X 3/4 25 110 067387-005 MOS90 “D” CONTROLLER 1
33 011248-004 NUT, 1/4-20 ESNA 38 111 067387-015 PC BOARD ASSEMBLY 1
34 025427-002 HANDLE 2 112 067387-016 RESISTOR BRACKET ASSEMBLY 1
36 067349-001 STAIR WELDMENT 1 113 067387-017 TACHOMETER BRACKET ASSEMBLY 1
37 011254-006 SCREW HHC 3/8-16 X 3/4 2 114 067387-018 SUPRESSION ASSEMBLY 1
38 011248-005 NUT HEX ESNA 5/16-18 UNC 6 115 067387-019 TERMINAL SUB ASSEMBLY 3
39 011240-005 WASHER 5/16 STD FLAT 16 116 067387-020 PUMP OVERRIDE CONTACTOR, SW200-673 1
40 011253-007 SCREW HHC 5/16-18UNC X 7/8 16 117 068552-000 PUMP TRACTION CONTACTOR, SW201-179 1
41 014025-005 NUT HEX CENTERLOCK 5/16-18UNC 16 118 068552-001 REV/FWD CONTACTOR, SW202-221 2
42 011821-004 SCREW BUTT HD. 1/4-20UNC X 1/2 4 119 068550-013 CONTACTOR BUSSBAR 2
43 011240-006 WASHER 3/8 STD FLAT 10 120 067387-021 CONTACTOR BUSSBAR 1
44 064462-014 PLUG HOLE 1 121 067387-022 FUSE, 300 AMP 2
45 067396-000 BATTERY SUPPORT 3 122 067387-023 RELAY, 48V 10A 1
46 068568-000 BATTERY 8 207 068777-003 CABLE ASSY. X 25” (5/16 X 3/8 LUG) REF
47 068334-010 BATTERY CABLE ASSY X 10 5 208 068777-004 CABLE ASSY. X 20” (5/16 X 3/8 LUG) REF
48 068332-004 BATTERY CABLE ASSY 1 211 029452-099 WIRE, 16 GA. BLACK 5
49 068574-001 CHARGER 1 218 014914-001 CONN. MALE PUSH, 14-16 .25 3
50 068332-003 BATTERY CABLE ASSY 1 219 029931-003 CONN. FEM. PUSH, 14-16 .25 3
51 067366-000 BATTERY CHARGER BRACKET 1 221 029601-015 CONN. RING, 14-16 Ø 3/8 1
52 067368-000 RELAY COVER 1 223 029440-099 CABLE, 12 GA. 3 COND. S.O REF
53 011252-012 SCREW HHC 1/4-20UNC X 1 1/2 4 *NOT SHOWN

Control Module Assembly

067360-007
Drawing 1 of 3

LX31/41 Electric/Bi-Energy Work Platform 6-47

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN

Control Module Assembly

067360-007
Drawing 2 of 3

6-48 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Control Module Assembly

067360-007
Drawing 3 of 3

LX31/41 Electric/Bi-Energy Work Platform 6-49

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Guardrail Installation, LX31/41 Electric & Bi-Energy
067530-005
ITEM PART NO DESCRIPTION QTY
1 0 REF PLATFORM WELDMENT 1
2 067751-002 SIDE GUARDRAIL WELDMENT 3
3 067751-001 GUARDRAIL WELDMENT R.H. 1
4 067883-000 GATE WELDMENT 1
5 003570-000 RETAINING PIN ASSY 1
6 062642-026 BEARING 2
7 066526-002 TORSION SPRING 1
8 067764-001 GATE KICKRAIL WELDMENT 1
9 011254-008 SCREW HHC 3/8-16UNC X 1 7
10 011254-032 SCREW HHC 3/8-16UNC X 4 8
11 064046-000 BRACKET, RAIL MOUNTING 6
12 011248-006 NUT HEX ESNA 3/8-16UNC 31
13 011254-018 SCREW HHC 3/8-16UNC X 2 1/4 4
14 011254-036 SCREW HHC 3/8-16UNC X 4-1/2 2
15 067881-000 END GUARDRAIL WELDMENT 1
16 067880-001 END GUARDRAIL WELDMENT 1
17 011254-014 SCREW HHC 3/8-16UNC X 1 3/4 8
18 067757-000 KICKRAIL WELDMENT 2
19 011254-020 SCR HHC 3/8-16 X 2-1/2 2
20 0067712-000 PIVOT TUBE WELDMENT 1
21 067695-000 SPACER 6
22 011739-014 ROLLPIN 3/8D X 1 3/4 1
23 011240-006 WASHER, FLAT STD 3/8 4
24 063666-004 WIRE CHANNEL 1
25 011253-012 SCREW HHC 5/16-18 X 1 1/2 2
26 011240-005 WASHER 5/16 FLAT 2
27 011250-005 NUT 5/16-18 HEX 2
28 067885-000 END RAIL WELDMENT 1

6-50 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Guardrail Installation
067530-005
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-51

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Guardrail Installation, LX31/41 Electric & Bi-Energy - Dual Deck
030841-300
ITEM PART NO DESCRIPTION QTY
1 030841-101 PLATFORM WELDMENT REF
2 030841-018 GUARDRAIL WELDMENT 1
3 030841-019 GUARDRAIL WELDMENT 1
4 067883-000 GATE WELDMENT 1
5 03570-000 RETAINING PIN ASSY 1
6 062642-026 BEARING 2
7 066526-002 TORSION SPRING 1
8 067764-001 GATE KICKRAIL WELDMENT 1
9 011254-008 SCREW HHC 3/8-16UNC X 1 6
10 030841-020 GUARDRAIL WELDMENT 3 1
11 030841-021 GUARDRAIL WELDMENT 4 1
12 011248-006 NUT HEX ESNA 3/8-16UNC 60
13 011254-018 SCREW HHC 3/8-16UNC X 2 1/4 28
14 030841-050 STEP WELDMENT 1
15 030841-054 CENTER GUARDRAIL WELDMENT 1
16 067755-001 SWING TUBE 12
17 011254-014 SCREW HHC 3/8-16UNC X 1 3/4 24
19 011254-20 SCR HHC 3/8-16 X 2-1/2 2
20 030841-013 PIVOT TUBE WELDMENT 1
21 067695-000 SPACER 6
22 011739-014 ROLLPIN 3/8D X 1 3/4 1
23 011240-006 WASHER, FLAT STD 3/8 8

6-52 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Guardrail Installation
030841-300
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-53

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Hose Kit Installation, LX31/41
067383-000
ITEM PART DESCRIPTION QTY.
1 100118-024 1 HOSE ASSY X 24 16FJX-16FJX 90ø 1
2 068763-040 1/4 HOSE ASSY X 40 4FJ X 6FJX 1
3 068745-334 3/8 HOSE ASSY X 334 6FJX-6FJX 1
4 068745-062 3/8 HOSE ASSY X 62 6FJX-6FJX 1
7 068745-035 3/8 HOSE ASSY X 35 6FJX-6FJX 1
8 068745-023 3/8 HOSE ASSY X 23 1/2 6FJX-6FJX 2
15 067683-109 3/8 HOSE ASSY X 109 6FJX-6FJX45ø 1
16 067683-118 3/8 HOSE ASSY X 118 6FJX-6FJX45ø 1
19 067684-236 3/8 HOSE ASSY X 236 6FJX-6FJX 1
21 065234-093 1/4 HOSE ASSY X 93 4FJX-4FJX 1
22 065234-062 1/4 HOSE ASSY X 62 4FJX-4FJX 1

Hose Kit Installation

067383-000
Drawing 1 of 1

6-54 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1
Control Cable Assembly, LX31 Control Cable Assembly, LX41
067536-000 067536-000
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.
1 067645-099 CABLE, 16/6, 18/12 MULTICONDUCTOR FT 62 2 067645-099 CABLE, 16/6, 18/12 MULTICONDUCTOR FT 72
4 029601-013 CONN RING TERM 16-14 GA #10 2 4 029601-013 CONN RING TERM 16-14 GA #10 2
5 063956-002 PIN, CONTACT MALE 20-14 GA 8 5 063956-002 PIN, CONTACT MALE 20-14 GA 8
6 029610-002 CONN FORK TERM 16-14 GA #8 6 6 029610-002 CONN FORK TERM 16-14 GA #8 6
7 029457-099 WIRE, 16GA GRN X 12 IN 1 7 029457-099 WIRE, 16GA GRN X 12 IN 1
8 029620-002 CONN, BUTT 16-14GA 2 8 029620-002 CONN, BUTT 16-14GA 2
9 029616-001 CONN, FEMALE PUSH 16-14GA X .188 2 9 029616-001 CONN, FEMALE PUSH 16-14GA X .188 2
10 029483-099 WIRE 16 GA RD/WHT X 14 IN 1 10 029483-099 WIRE 16 GA RD/WHT X 14 IN 1

Control Cable Assembly

067536-000/001
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-55

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Lower Control Box Assembly, LX31/41
067362-001
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.

1 067825-001 ENCLOSURE 1 25 064462-002 PLUG, 1/2 DIA. FLUSH 1

2 067363-001 PANEL ASSEMBLY, ELEC. 1 101 029825-002 DIODE 3 AMP 25
3 064417-001 MOUNTING LATCH 5 102 029610-002 TERMINAL #8 FORK 35
4 064443-001 CONTACT BLOCK, N.O. 4 103 029610-003 TERMINAL #6 FORK 31
5 064443-002 CONTACT BLOCK, N.C. 3 104 060214-099 WIRE 16 AWG 15 COND FT 2
6 067652-000 PUSH BUTTON, MOM. FLUSH ,GREEN 2 105 029496-099 CABLE 2 COND 16GA FT 22
7 067653-000 PUSH BUTTON, MOM. EXT. RED 2 106 029447-099 CABLE 3 COND 16GA FT 14
8 067654-000 PUSH BUTTON, MOM. FLUSH, BLK. 1 107 005491-099 WIRE 16GA GRN/BLK FT 1
9 066807-003 ALARM, DOWN 1 108 029450-099 WIRE 16GA BLU FT 8
10 068582-010 CIRCUIT BREAKER, 10 AMP. 2 109 029451-099 WIRE 16GA WHT FT 6
11 064446-003 PUSH BUTTON, MUSHROOM, RED 1 110 029452-099 WIRE 16GA BLK FT 10
13 064445-011 SELECTOR SWITCH, 3 POS. 1 111 029456-099 WIRE 16GA YEL FT 2
14 011252-006 SCREW HHC 1/4-20UNC X 3/4 2 112 029457-099 WIRE 16GA GRN FT 1
15 011248-006 NUT, SELF LOCKING, 3/8-16 4 113 029459-099 WIRE 16GA BLU/WHT FT 5
16 014996-006 FLATWASHER, 3/8” 4 114 029475-099 WIRE 16GA BLU/BLK FT 4
17 029925-010 CABLE CONNECTOR 4 115 029477-099 WIRE 16GA ORN/BLK FT 4
18 029925-000 CABLE CONNECTOR, 1/2” 1 116 029478-099 WIRE 16GA RED/BLK FT 4
19 029939-003 CONDUIT NUT, 3/4” 2 117 029482-099 WIRE 16GA GRN/WHT FT 2
20 029939-002 CONDUIT NUT, 1/2” 3 118 029483-099 WIRE 16GA RED/WHT FT 2
21 066807-001 ALARM 2 119 029731-012 RESISTOR, 100 OHM 1
22 014996-004 WASHER 1/4 SAE 2 120 029620-002 CONN 16GA BUTT 2
23 066516-000 PLUG, HOLE 2.09 DIA. 1 122 063956-002 CONNECTER PIN 15
24 064462-029 PLUG, 15/16 DIA. FLUSH 3 123 063956-006 PLUG 15 POSITION 1

Lower Control Box Assembly

067362-001
Drawing 1 of 2

6-56 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Lower Control Box Assembly

067362-001
Drawing 2 of 2

LX31/41 Electric/Bi-Energy Work Platform 6-57

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Controller Assembly 48V, LX31/41 Electric
067384-001
ITEM PART DESCRIPTION QTY.
1 067487-000 LX CONTROL BOX 1
2 067385-000 CONTROLLER 48V 1
3 064417-001 MOUNTING LATCH 2
4 064462-007 CAP PLUG 7/8 DIA. 2
5 029925-011 CABLE CONNECTOR, 3/4” 1
6 029939-002 CONDUIT NUT, 1/2” 2
7 029939-003 CONDUIT NUT, 3/4” 1
8 068807-000 KEY OPERATE 1
9 066805-002 SELECTOR SWITCH 2
10 067653-000 PUSH BUTTON 1
11 064446-003 MUSHROOM BUTTON 1
12 068133-001 INDICATOR LIGHT GRN 1
13 067806-000 RING, RETAINING 1
14 063951-003 RELAY 2
15 064443-001 CONTACT BLOCK, N.O. 1
16 064443-002 CONTACT BLOCK, N.C. 1
18 067483-000 CONTROLLER SUPPORT 1
19 067486-000 COVER PLATE, CONTROLLER BOX 1
20 068889-099 WEATHERSTRIP 1/2 X 3/16 FOAM 3 FT
21 064462-002 CAPLUG 1/2” DIA. 4
22 010952-004 SCREW BUTT HD TORX 10-24UNC X 1/2 6
23 011715-004 SCREW, #6-32 X 1/2 4
24 011248-047 LOCKNUT, #6-32 4
25 066805-011 CONTACT BLOCK N.C. 2
26 066805-010 CONTACT BLOCK N.O. 2
27 011252-006 SCREW, 1/4-20 UNC HEX HEAD CAP x 3/4 2
28 011248-004 LOCKNUT, 1/4-20 UNC 2
101 029610-004 CONNECTOR FORK TERM 12-10 GA. #10 15
102 029620-002 CONNECTOR BUTT. 16-14 GA. 4
103 029615-002 CONNECTOR FEMALE PUSH 16-14 GA. 4
104 029452-099 WIRE, 16 GA. BLACK 1FT
105 029450-099 WIRE, 16 GA. BLUE 1FT
109 029453-099 WIRE, 16 GA. ORG 1FT
110 063956-003 PLUG, HOUSING 1
111 063956-010 PIN, CONTACT MALE 11
112 029477-099 WIRE, 16GA. ORG/BLK 1FT
113 029454-099 WIRE, 16 GA. RED 2FT
114 029731-008 RESISTER 1

Controller Assembly 48V

067384-001
Drawing 1 of 2

6-58 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Controller Assembly 48V

067384-001 Drawing 2 of 2

LX31/41 Electric/Bi-Energy Work Platform 6-59

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Controller Assembly 48V, LX31/41 Bi-Energy
067384-000
ITEM PART DESCRIPTION QTY.
1 067487-000 LX CONTROL BOX 1
2 067385-000 CONTROLLER 48V 1
3 064417-001 MOUNTING LATCH 2
4 064462-007 CAP PLUG 7/8 DIA. 2
5 029925-010 CABLE CONNECTOR, 3/4” 1
6 029939-002 CONDUIT NUT, 1/2” 2
7 029939-003 CONDUIT NUT, 3/4” 1
8 068819-000 KEY OPERATE 1
9 066805-002 SELECTOR SWITCH 2
10 067653-000 PUSH BUTTON 1
11 064446-003 MUSHROOM BUTTON 1
12 068133-001 INDICATOR LIGHT GRN 1
13 067806-000 RING, RETAINING 1
14 063951-003 RELAY 2
15 064443-001 CONTACT BLOCK, N.O. 1
16 064443-002 CONTACT BLOCK, N.C. 1
18 067483-000 CONTROLLER SUPPORT 1
19 067486-000 COVER PLATE, CONTROLLER BOX 1
20 068889-099 WEATHERSTRIP 1/2 X 3/16 FOAM 3 FT
21 064462-002 CAPLUG 1/2” DIA. 4
22 010952-004 SCREW BUTT HD TORX 10-24UNC X 1/2 6
23 011715-004 SCREW, #6-32 X 1/2 4
24 011248-047 LOCKNUT, #6-32 4
25 066805-010 CONTACT BLOCK N.O. 2
26 066805-011 CONTACT BLOCK N.C. 3
27 011252-006 SCREW, 1/4-20 UNC HEX HEAD CAP x 3/4 2
28 011248-004 LOCKNUT, 1/4-20 UNC 2
101 029610-004 CONNECTOR FORK TERM 12-10 GA. #10 15
102 029620-002 CONNECTOR BUTT. 16-14 GA. 4
103 029615-002 CONNECTOR FEMALE PUSH 16-14 GA. 8
104 029452-099 WIRE 16 GA. BLACK FT 1
105 029450-099 WIRE 16 GA. BLUE FT 1
109 029453-099 WIRE 16 GA. ORG FT 1
110 063956-003 PLUG, HOUSING 1
111 063956-010 PIN, CONTACT MALE 11
112 029477-099 WIRE 16 GA. ORG/BLK FT 1
113 029454-099 WIRE 16 GA. RED FT 2

Controller Assembly
48V
067384-000

6-60 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Controller Assembly 48V

067384-000 Drawing 2 of 2

LX31/41 Electric/Bi-Energy Work Platform 6-61

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Scissors Guard, LX31 Bi-Energy
067373-000
ITEM PART NO DESCRIPTION QTY. ITEM PART NO DESCRIPTION QTY.

1 067935-001 WELDMENT, LADDER 1 10 011252-008 SCREW HHC 1/4-20 X 1 32

2 067941-000 CHANNEL, GUARD MOUNT 3 11 011240-004 WASHER 1/4 STD FLAT 25
3 067942-000 SPACER 1 12 011248-004 NUT 1/4-20 ESNA 33
4 067943-001 WELDMENT, FRONT GUARD 1 13 011256-016 SCREW HHC 1/2-13 X 2 4
5 067381-003 WELDMENT, GUARD FRONT 2 14 011240-008 WASHER 1/2 STD FLAT 4
6 067380-002 WELDMENT, GUARD REAR 2 15 011248-008 NUT 1/2-13 ESNA 4
7 067946-001 WELDMENT, REAR GUARD RH 1 17 067946-011 WELDMENT, REAR GUARD LH 1
8 060830-000 SAFETY WALK 5 18 067378-001 GUARDRAIL SIDE WELDMENT 2
9 011252-012 SCREW HHC 1/4-20 X 1 1/2 1

6-62 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1
Scissors Guard, LX41 Bi-Energy
067373-001
ITEM PART NO DESCRIPTION QTY. ITEM PART NO DESCRIPTION QTY.

1 067935-000 WELDMENT, LADDER 1 10 011252-008 SCREW HHC 1/4-20 X 1 32

2 067941-000 CHANNEL, GUARD MOUNT 3 11 011240-004 WASHER 1/4 STD FLAT 25
3 067942-000 SPACER, GUARD MOUNT 1 12 011248-004 NUT 1/4-20 ESNA 33
4 067943-000 WELDMENT, FRONT GUARD 1 13 011256-008 SCREW HHC 1/2-13 X 1 4
5 067381-004 WELDMENT, GUARD FRONT 2 14 011240-008 WASHER 1/2 STD FLAT 4
6 067380-003 WELDMENT, GUARD REAR 2 15 011248-008 NUT 1/2-13 ESNA 4
7 067946-000 WELDMENT, REAR GUARD RH 1 17 067946-010 WELDMENT, REAR GUARD LH 1
8 060830-000 SAFETY WALK 6 18 067378-001 GUARDRAIL SIDE TUBE WELDMENT 2
9 011252-012 SCREW HHC 1/4-20 X 1 1/2 1

LX31/41 Electric/Bi-Energy Work Platform 6-63

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Scissors Guard, LX31 Electric
067373-003
ITEM PART NO DESCRIPTION QTY. ITEM PART NO DESCRIPTION QTY.

1 030860-601 WELDMENT, LADDER 1 10 011252-008 SCREW HHC 1/4-20 X 1 32

2 067941-000 CHANNEL, GUARD MOUNT 3 11 011240-004 WASHER 1/4 STD FLAT 25
3 067942-000 SPACER, GUARD MOUNT 1 12 011248-004 NUT 1/4-20 ESNA 33
4 030860-602 WELDMENT, FRONT GUARD 1 13 011256-008 SCREW HHC 1/2-13 X 1 4
5 067381-003 WELDMENT, GUARD FRONT 2 14 011240-008 WASHER 1/2 STD FLAT 4
6 067380-002 WELDMENT, GUARD REAR 2 15 011248-008 NUT 1/2-13 ESNA 4
7 067946-000 WELDMENT, REAR GUARD RH 1 17 067946-011 WELDMENT, REAR GUARD LH 1
8 060830-000 SAFETY WALK 4 18 067378-001 GUARDRAIL SIDE WELDMENT 2
9 011252-012 SCREW HHC 1/4-20 X 1 1/2 1

6-64 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1
Scissors Guard, LX41 Electric
067373-004
ITEM PART NO DESCRIPTION QTY. ITEM PART NO DESCRIPTION QTY.

1 030841-601 WELDMENT, LADDER 1 10 011252-008 SCREW HHC 1/4-20 X 1 32

2 067941-000 CHANNEL, GUARD MOUNT 3 11 011240-004 WASHER 1/4 STD FLAT 25
3 067942-000 SPACER, GUARD MOUNT 1 12 011248-004 NUT 1/4-20 ESNA 33
4 030841-602 WELDMENT, FRONT GUARD 1 13 011256-008 SCREW HHC 1/2-13 X 1 4
5 067381-004 WELDMENT, GUARD FRONT 2 14 011240-008 WASHER 1/2 STD FLAT 4
6 067380-003 WELDMENT, GUARD REAR 2 15 011248-008 NUT 1/2-13 ESNA 4
7 067946-000 WELDMENT, REAR GUARD RH 1 17 067946-010 WELDMENT, REAR GUARD LH 1
8 060830-000 SAFETY WALK 4 18 067378-001 GUARDRAIL SIDE 2
9 011252-012 SCREW HHC 1/4-20 X 1 1/2 1

LX31/41 Electric/Bi-Energy Work Platform 6-65

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Tire & Wheel Assembly, Front, LX31/41
067665-004
ITEM PART DESCRIPTION QTY.
1 067609-001 WHEEL, 16.5 X 8.25 8 HOLE, 8 BC 1
2 068555-000 TIRE, 9.5 X 16.5 NHS 10 PLY 1
3 012282-001 VALVE STEM 1

Tire & Wheel Assembly, Front

067665-004
Drawing 1 of 1

6-66 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1
Tire & Wheel Assembly, Rear, LX31/41
068327-000
ITEM PART DESCRIPTION QTY.
1 068555-000 TIRE 16.5 X 9.50 10 PLY 1
2 067609-000 WHEEL 16.5 X 8.25, 6 HOLE ON 6” B.C. 1
3 012282-001 VALVE STEM 1

Tire & Wheel Assembly, Rear

067327-000
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-67

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Label Kit/Installation, LX31 Electric Label Kit/Installation, LX41 Electric
067361-012 067361-013
ITEM PART NO DESCRIPTION QTY ITEM PART NO DESCRIPTION QTY
1 010076-000 MANUAL CASE 1 1 010076-000 MANUAL CASE 1
2 010076-001 LABEL-ATTENTION 1 2 010076-001 LABEL-ATTENTION 1
3 067449-020 USER MANUAL LX-SERIES 1 3 067449-020 USER MANUAL LX-SERIES 1
4 060197-000 LABEL-HYD. FLUID 1 4 060197-000 LABEL-HYD. FLUID 1
5 061205-001 NAME PLATE EURO 1 5 061205-001 NAME PLATE EURO 1
6 030768-001 LABEL CE 1 6 030768-001 LABEL CE 1
8 067365-000 LABEL-LOWER CONTEOLLER 1 8 067365-000 LABEL-LOWER CONTEOLLER 1
9 066552-000 LABEL-WARNING BATTERY 1 9 066552-000 LABEL-WARNING BATTERY 1
10 064444-000 LABEL-USA 4 10 064444-000 LABEL-USA 4
11 067642-005 LABEL-CONTROLLER 1 11 067642-005 LABEL-CONTROLLER 1
13 067639-001 LABEL-PLATFORM CONTROLS 1 13 067639-001 LABEL-PLATFORM CONTROLS 1
14 066550-009 LABEL-DANGER 1 14 066550-009 LABEL-DANGER 1
15 066551-002 LABEL-CAUTION 1 15 066551-002 LABEL-CAUTION 1
16 066551-003 LABEL-DANGER TIPPING 1 16 066551-003 LABEL-DANGER TIPPING 1
17 062562-002 LABEL BATTERY 120 LBS 1 17 062562-002 LABEL BATTERY 120 LBS 1
19 066554-000 LABEL-READ 1 19 066554-000 LABEL-READ 1
20 066555-000 LABEL-DO NOT ADJUST 2 20 066555-000 LABEL-DO NOT ADJUST 2
21 063423-000 LABEL-BRAKE RELEASE 1 21 063423-000 LABEL-BRAKE RELEASE 1
22 066562-001 LABEL-TIRE PSI 75 1 22 066562-001 LABEL-TIRE PSI 75 1
23 061515-000 LABEL-LIFT HERE 1 23 061515-000 LABEL-LIFT HERE 1
24 066568-000 LABEL-WARNING 1 24 066568-000 LABEL-WARNING 1
26 066557-010 LABEL-MAX LOAD 2000 LBS 2 26 066557-007 LABEL-MAX LOAD 1500 LBS 2
27 066561-001 LABEL, MAINT. BRACE 1 27 066561-001 LABEL, MAINT. BRACE 1
28 061683-005 LABEL-UPRIGHT 4 1/2 3 28 061683-005 LABEL-UPRIGHT 4 1/2 3
29 061683-007 LABEL-UPRIGHT 5 1/2 4 29 061683-007 LABEL-UPRIGHT 5 1/2 4
30 067644-002 LABEL-LX31 2WD 3 30 067644-004 LABEL-LX41 2WD 3
31 067644-001 LABEL-LX31 2WD 4 31 067644-003 LABEL-LX41 2WD 4
33 011248-004 NUT HEX ESNA 1/4-20UNC 4 33 011248-004 NUT HEX ESNA 1/4-20UNC 4
35 011252-008 SCREW HHC 1/4-20UNC X 1 4 35 011525-008 SCREW HHC 1/4-20UNC X 1 4
36 065368-000 TACK 4 36 065368-000 TACK 4
37 060830-000 SAFETY WALK 4 37 060830-000 SAFETY WALK 4
39 060086-000 SAFETY WALK 20 X 32 12 39 060086-000 SAFETY WALK 20 X 32 12
40 066558-000 LABEL, EMERG. LOWERING 2 40 066558-000 LABEL, EMERG. LOWERING 2
41 068641-003 LABEL, PARKING BRAKE 1 41 068641-003 LABEL, PARKING BRAKE 1

6-68 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Label Kit/Installation, LX31

067361-012/013
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-69

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
German Label Kit/Installation, German Label Kit/Installation,
LX31 Electric LX41 Electric
067361-015 067361-016
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.
1 010076-000 MANUAL CASE 1 1 010076-000 MANUAL CASE 1
3 067449-020 USER MANUAL LX-SERIES 1 3 067449-020 USER MANUAL LX-SERIES 1
4 064917-000 LABEL-HYD. FLUID 1 4 064917-000 LABEL-HYD. FLUID 1
5 061205-001 NAME PLATE EURO 1 5 061205-001 NAME PLATE EURO 1
8 067365-100 LABEL-LOWER CONTROLLER 8 067365-100 LABEL-LOWER CONTROLLER
10 064444-000 LABEL-USA 4 10 064444-000 LABEL-USA 4
11 067642-205 LABEL-CONTROLLER 1 11 067642-205 LABEL-CONTROLLER 1
13 064941-002 LABEL PLATFORM CONTROLS 1 13 064941-002 LABEL PLATFORM CONTROLS 1
14 064935-000 LABEL DANGER 1 14 064935-000 LABEL DANGER 1
17 062562-102 LABEL BATTERY 120 LBS 1 17 062562-102 LABEL BATTERY 120 LBS 1
23 064937-000 LABEL-LIFT HERE 1 23 064937-000 LABEL-LIFT HERE 1
26 064910-014 LABEL-MAX LOAD 2000LB / 910KG 2 26 064910-011 LABEL-MAX LOAD 1500LB / 680KG 2
28 061683-005 LABEL-UPRIGHT 4 1/2 3 28 061683-005 LABEL-UPRIGHT 4 1/2 3
29 061683-007 LABEL-UPRIGHT 5 1/2 4 29 061683-007 LABEL-UPRIGHT 5 1/2 4
30 067644-002 LABEL-LX31 2WD x 4 1/2” 3 30 067644-004 LABEL-LX41 2WD x 4 1/2” 3
31 067644-001 LABEL LX31 2WD x 6 1/2” 4 31 067644-003 LABEL LX41 2WD x 6 1/2” 4
32 030768-001 LABEL CE 1 32 030768-001 LABEL CE 1
33 011248-004 NUT HEX ESNA 1/4-20UNC 4 33 011248-004 NUT HEX ESNA 1/4-20UNC 4
35 011252-008 SCREW HHC 1/4-20UNC X 1 4 35 011252-008 SCREW HHC 1/4-20UNC X 1 4
36 065368-000 TACK 4 36 065368-000 TACK 4
37 060830-000 SAFETY WALK 4 37 060830-000 SAFETY WALK 4
39 060086-000 SAFETY WALK 20 X 32 12 39 060086-000 SAFETY WALK 20 X 32 12
40 064912-002 LABEL, EMERG. LOWERING 2 40 064912-002 LABEL, EMERG. LOWERING 2

6-70 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Label Kit/Installation, LX41

067361-015/016
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-71

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Label Kit/Installation, LX31 Bi-Energy Label Kit/Installation, LX41 Bi-Energy
067361-003 067361-004
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.
1 010076-000 MANUAL CASE 1 1 010076-000 MANUAL CASE 1
2 010076-001 LABEL-ATTENTION 1 2 010076-001 LABEL-ATTENTION 1
3 067449-020 USER MANUAL LX-SERIES 1 3 067449-020 USER MANUAL 1
4 060197-000 LABEL-HYD. FLUID 1 4 060197-000 LABEL-HYD. FLUID 1
5 061205-001 NAME PLATE EURO 1 5 061205-001 NAME PLATE EURO 1
6 030768-001 LABEL CE 1 6 030768-001 LABEL CE 1
7 067822-001 LABEL-GLOW INST. 2 7 067822-001 LABEL-GLOW INST. 2
8 067365-000 LABEL-LOWER CONTEOLLER 1 8 067365-000 LABEL-LOWER CONTEOLLER 1
9 066552-000 LABEL-WARNING BATTERY 1 9 066552-000 LABEL-WARNING BATTERY 1
10 064444-000 LABEL-USA 4 10 064444-000 LABEL-USA 4
11 067642-005 LABEL-CONTROLLER 1 11 067642-005 LABEL-CONTROLLER 1
12 067638-001 LABEL-MOTOR CONTROLS 1 12 067638-001 LABEL-MOTOR CONTROLS 1
13 067639-001 LABEL-PLATFORM CONTROLS 1 13 67639-001 LABEL-PLATFORM CONTROL 1
14 066550-009 LABEL-DANGER 1 14 066550-009 LABEL-DANGER 1
15 066551-002 LABEL-CAUTION 1 15 066551-002 LABEL-CAUTION 1
16 066551-003 LABEL-DANGER TIPPING 1 16 066551-003 LABEL-DANGER TIPPING 1
17 062562-002 LABEL BATTERY 120 LBS 1 17 062562-002 LABEL BATTERY 120 LBS 1
19 066554-000 LABEL-READ 1 19 066554-000 LABEL-READ 1
20 066555-000 LABEL-DO NOT ADJUST 2 20 066555-000 LABEL-DO NOT ADJUST 2
21 063423-000 LABEL-BRAKE RELEASE 1 21 063423-000 LABEL-BRAKE RELEASE 1
22 066562-001 LABEL-TIRE PSI 75 1 22 066562-001 LABEL-TIRE PSI 75 1
23 061515-000 LABEL-LIFT HERE 1 23 061515-000 LABEL-LIFT HERE 1
24 066568-000 LABEL-WARNING 1 24 066568-000 LABEL-WARNING 1
25 027898-000 LABEL - DIESEL FUEL 1 25 027898-000 LABEL - DIESEL FUEL 1
26 066557-010 LABEL-MAX LOAD 2000 LBS 2 26 066557-007 LABEL-MAX LOAD 1500 LBS 2
27 066561-001 LABEL, MAINT. BRACE 1 27 066561-001 LABEL, MAINT. BRACE 1
28 061683-005 LABEL-UPRIGHT 4 1/2 3 28 061683-005 LABEL-UPRIGHT 4 1/2 3
29 061683-007 LABEL-UPRIGHT 5 1/2 2 29 061683-007 LABEL-UPRIGHT 5 1/2 2
30 067644-002 LABEL-LX31 2WD 3 30 067644-004 LABEL-LX41 2WD 3
31 067644-001 LABEL-LX31 2WD 4 31 067644-003 LABEL-LX41 2WD 4
33 011248-004 NUT HEX ESNA 1/4-20UNC 4 33 011248-004 NUT HEX ESNA 1/4-20UNC 4
34 067538-000 LABEL BI-ENERGY 2 34 067538-000 LABEL BI-ENERGY 2
35 011252-008 SCREW HHC 1/4-20UNC X 1 4 35 011252-008 SCREW HHC 1/4-20UNC X 1 4
36 065368-000 TACK 4 36 065368-000 TACK 4
37 060830-000 SAFETY WALK 4 37 060830-000 SAFETY WALK 4
39 060086-000 SAFETY WALK 20 X 32 12 39 060086-000 SAFETY WALK 20 X 32 12
40 066558-000 LABEL, EMERG. LOWERING 2 40 066558-000 LABEL, EMERG. LOWERING 2
41 068641-003 LABEL, PARKING BRAKE 1 41 068641-003 LABEL, PARKING BRAKE 1

6-72 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Label Kit/Installation, LX41

067361-003/004
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-73

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
German Label Kit/Installation, German Label Kit/Installation,
LX31 Bi-Energy LX41 Bi-Energy
067361-006 067361-007
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.
1 010076-000 MANUAL CASE 1 1 010076-000 MANUAL CASE 1
3 067449-020 USER MANUAL LX-SERIES 1 3 067449-020 USER MANUAL LX-SERIES 1
4 064917-000 LABEL-HYD. FLUID 1 4 064917-000 LABEL-HYD. FLUID 1
5 061205-001 NAME PLATE EURO 1 5 061205-001 NAME PLATE EURO 1
8 067365-100 LABEL-LOWER CONTEOLLER 1 8 067365-100 LABEL-LOWER CONTEOLLER 1
10 064444-000 LABEL-USA 4 10 064444-000 LABEL-USA 4
11 067642-205 LABEL-CONTROLLER 1 11 067642-205 LABEL-CONTROLLER 1
12 064941-003 LABEL MOTOR CONTROLS 1 12 064941-003 LABEL MOTOR CONTROLS 1
13 064941-002 LABEL PLATFORM CONTROLS 1 13 064941-002 LABEL PLATFORM CONTROLS 1
14 064935-000 LABEL DANGER 1 14 064935-000 LABEL DANGER 1
17 062562-102 LABEL BATTERY 120 LBS 1 17 062562-102 LABEL BATTERY 120 LBS 1
23 064937-000 LABEL-LIFT HERE 1 23 064937-000 LABEL-LIFT HERE 1
26 064910-014 LABEL-MAX LOAD 2000LB / 910KG 2 26 064910-011 LABEL-MAX LOAD 1500LB / 680KG 2
28 061683-005 LABEL-UPRIGHT 4 1/2 3 28 061683-005 LABEL-UPRIGHT 4 1/2 3
29 061683-007 LABEL-UPRIGHT 5 1/2 3 29 061683-007 LABEL-UPRIGHT 5 1/2 3
30 067644-002 LABEL-LX31 2WD x 4 1/2” 3 30 067644-004 LABEL-LX41 2WD x 4 1/2” 3
31 067644-001 LABEL LX31 2WD x 6 1/2” 2 31 067644-003 LABEL LX41 2WD x 6 1/2” 2
32 030768-001 LABEL CE 1 32 030768-001 LABEL CE 1
33 011248-004 NUT HEX ESNA 1/4-20UNC 4 33 011248-004 NUT HEX ESNA 1/4-20UNC 4
34 067538-000 LABEL, BI-ENERGY 2 34 067538-000 LABEL, BI-ENERGY 2
35 011252-008 SCREW HHC 1/4-20UNC X 1 4 35 011252-008 SCREW HHC 1/4-20UNC X 1 4
36 065368-000 TACK 4 36 065368-000 TACK 4
37 060830-000 SAFETY WALK 4 37 060830-000 SAFETY WALK 4
39 060086-000 SAFETY WALK 20 X 32 12 39 060086-000 SAFETY WALK 20 X 32 12
40 064912-002 LABEL, EMERG. LOWERING 2 40 064912-002 LABEL, EMERG. LOWERING 2

6-74 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Label Kit/Installation, LX41

067361-006/007
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-75

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Label Kit/Installation, Label Kit/Installation,
LX31 Electric - Dual Deck LX41 Electric - Dual Deck
067361-030 067361-031
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.
1 010076-000 MANUAL CASE 1 1 010076-000 MANUAL CASE 1
2 010076-001 LABEL-ATTENTION 1 2 010076-001 LABEL-ATTENTION 1
3 067449-020 USER MANUAL LX-SERIES - 3 067449-020 USER MANUAL LX-SERIES .
4 060197-000 LABEL-HYD. FLUID 1 4 060197-000 LABEL-HYD. FLUID 1
5 061205-001 NAME PLATE 1 5 061205-001 NAME PLATE 1
6 030768-001 LABEL-CE 1 6 030768-001 LABEL-CE 1
8 067365-000 LABEL-LOWER CONTEOLLER 1 8 067365-000 LABEL-LOWER CONTEOLLER 1
9 066552-000 LABEL-WARNING BATTERY 1 9 066552-000 LABEL-WARNING BATTERY 1
10 064444-000 LABEL-USA 4 10 064444-000 LABEL-USA 4
11 067642-005 LABEL-CONTROLLER 1 11 067642-005 LABEL-CONTROLLER 1
13 067639-001 LABEL-PLATFORM CONTROLS 1 13 067639-001 LABEL-PLATFORM CONTROLS 1
14 066550-009 LABEL-DANGER 1 14 066550-009 LABEL-DANGER 1
15 066551-002 LABEL-CAUTION 1 15 066551-002 LABEL-CAUTION 1
16 066551-003 LABEL-DANGER TIPPING 1 16 066551-003 LABEL-DANGER TIPPING 1
17 062562-002 LABEL-BATTERY 120 LBS 1 17 062562-002 LABEL-BATTERY 120 LBS 1
19 066554-000 LABEL-READ 1 19 066554-000 LABEL-READ 1
20 066555-000 LABEL-DO NOT ADJUST 2 20 066555-000 LABEL-DO NOT ADJUST 2
21 063423-000 LABEL-BRAKE RELEASE 1 21 063423-000 LABEL-BRAKE RELEASE 1
22 066562-001 LABEL-TIRE PSI 75 1 22 066562-001 LABEL-TIRE PSI 75 1
23 061515-000 LABEL-LIFT HERE 1 23 061515-000 LABEL-LIFT HERE 1
24 066568-000 LABEL-WARNING 1 24 066568-000 LABEL-WARNING 1
26 066557-013 LABEL-MAX LOAD 1750 LBS 2 26 066557-006 LABEL-MAX LOAD 1250 LBS 2
27 061683-004 LABEL-UPRIGHT 2 1/2 1 27 061683-004 LABEL-UPRIGHT 2 1/2 1
28 061683-005 LABEL-UPRIGHT 4 1/2 3 28 061683-005 LABEL-UPRIGHT 4 1/2 3
29 061683-007 LABEL-UPRIGHT 5 1/2 3 29 061683-007 LABEL-UPRIGHT 5 1/2 3
30 067644-002 LABEL-LX31 2WD 4 30 067644-004 LABEL-LX41 2WD 4
31 067644-001 LABEL-LX31 2WD 3 31 067644-003 LABEL-LX41 2WD 3
33 011248-004 NUT HEX ESNA 1/4-20UNC 4 33 011248-004 NUT HEX ESNA 1/4-20UNC 4
35 011525-008 SCREW HHC 1/4-20UNC X 1 4 35 011525-008 SCREW HHC 1/4-20UNC X 1 4
36 065368-000 TACK 4 36 065368-000 TACK 4
37 060830-000 SAFETY WALK 4 37 060830-000 SAFETY WALK 4
38 066561-001 LABEL, MAINT. BRACE 1 38 066561-001 LABEL, MAINT. BRACE 1
39 060086-000 SAFETY WALK 20 X 32 12 39 060086-000 SAFETY WALK 20 X 32 12
40 066558-000 LABEL, EMERG. LOWERING 2 40 066558-000 LABEL, EMERG. LOWERING 2
41 068641-003 LABEL, PARKING BRAKE 1 41 068641-003 LABEL, PARKING BRAKE 1

6-76 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Label Kit/Installation, LX41

067361-030/031
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-77

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
German Label Kit/Installation, German Label Kit/Installation,
LX31 Electric - Dual Deck LX41 Electric - Dual Deck
067361-033 067361-034
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.
1 010076-000 MANUAL CASE 1 1 010076-000 MANUAL CASE 1
3 067449-020 USER MANUAL LX-SERIES 1 3 067449-020 USER MANUAL LX-SERIES 1
4 064917-000 LABEL-HYD. FLUID 1 4 064917-000 LABEL-HYD. FLUID 1
5 61205-001 NAME PLATE EURO 1 5 61205-001 NAME PLATE EURO 1
8 067365-100 LABEL-LOWER CONTEOLLER 1 8 067365-100 LABEL-LOWER CONTEOLLER 1
10 064444-000 LABEL-USA 4 10 064444-000 LABEL-USA 4
11 067642-205 LABEL-CONTROLLER 1 11 067642-205 LABEL-CONTROLLER 1
13 064941-002 LABEL PLATFORM CONTROLS 1 13 064941-002 LABEL PLATFORM CONTROLS 1
14 064935-000 LABEL DANGER 1 14 064935-000 LABEL DANGER 1
17 062562-102 LABEL BATTERY 120 LBS 1 17 062562-102 LABEL BATTERY 120 LBS 1
23 064937-000 LABEL-LIFT HERE 1 23 064937-000 LABEL-LIFT HERE 1
26 064910-016 LABEL-MAX LOAD 1750LB / 795KG 2 26 064910-010 LABEL-MAX LOAD 1250LB / 567KG 2
27 061683-004 LABEL-UPRIGHT 2-1/2 1 27 061683-004 LABEL-UPRIGHT 2-1/2 1
28 061683-005 LABEL-UPRIGHT 4 1/2 2 28 061683-005 LABEL-UPRIGHT 4 1/2 2
29 061683-007 LABEL-UPRIGHT 5 1/2 3 29 061683-007 LABEL-UPRIGHT 5 1/2 3
30 067644-002 LABEL-LX31 2WD x 4 1/2” 3 30 067644-004 LABEL-LX41 2WD x 4 1/2” 3
31 067644-001 LABEL LX31 2WD x 6 1/2” 3 31 067644-003 LABEL LX41 2WD x 6 1/2” 3
32 030768-001 LABEL CE 1 32 030768-001 LABEL CE 1
33 011248-004 NUT HEX ESNA 1/4-20UNC 4 33 011248-004 NUT HEX ESNA 1/4-20UNC 4
35 011252-008 SCREW HHC 1/4-20UNC X 1 4 35 011252-008 SCREW HHC 1/4-20UNC X 1 4
36 065368-000 TACK 4 36 065368-000 TACK 4
37 060830-000 SAFETY WALK 4 37 060830-000 SAFETY WALK 4
39 060086-000 SAFETY WALK 20 X 32 12 39 060086-000 SAFETY WALK 20 X 32 12
40 064912-002 LABEL, EMERG. LOWERING 2 40 064912-002 LABEL, EMERG. LOWERING 2

6-78 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Label Kit/Installation, LX41

067361-033/034
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-79

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Label Kit/Installation, Label Kit/Installation,
LX31 Bi-Energy - Dual Deck LX41 Bi-Energy - Dual Deck
067361-021 067361-022
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.
1 010076-000 MANUAL CASE 1 1 010076-000 MANUAL CASE 1
2 010076-001 LABEL-ATTENTION 1 2 010076-001 LABEL-ATTENTION 1
3 067449-020 USER MANUAL LX-SERIES - 3 067449-020 USER MANUAL LX-SERIES -
4 060197-000 LABEL-HYD. FLUID 1 4 060197-000 LABEL-HYD. FLUID 1
5 061205-001 NAME PLATE 1 5 061205-001 NAME PLATE 1
6 030768-001 LABEL CE 1 6 030768-001 LABEL CE 1
7 067822-001 LABEL-GLOW INST. 2 7 067822-001 LABEL-GLOW INST. 2
8 067365-000 LABEL-LOWER CONTEOLLER 1 8 067365-000 LABEL-LOWER CONTEOLLER 1
9 066552-000 LABEL-WARNING BATTERY 1 9 066552-000 LABEL-WARNING BATTERY 1
10 064444-000 LABEL-USA 4 10 064444-000 LABEL-USA 4
11 067642-005 LABEL-CONTROLLER 1 11 067642-005 LABEL-CONTROLLER 1
12 067638-002 LABEL-MOTOR CONTROLS 1 12 067638-002 LABEL-MOTOR CONTROLS 1
13 067639-001 LABEL-PLATFORM CONTROLS 1 13 067639-001 LABEL-PLATFORM CONTROLS 1
14 066550-009 LABEL-DANGER 1 14 066550-009 LABEL-DANGER 1
15 066551-002 LABEL-CAUTION 1 15 066551-002 LABEL-CAUTION 1
16 066551-003 LABEL-DANGER TIPPING 1 16 066551-003 LABEL-DANGER TIPPING 1
17 062562-002 LABEL-BATTERY 120 LBS 1 17 062562-002 LABEL-BATTERY 120 LBS 1
19 066554-000 LABEL-READ 1 19 066554-000 LABEL-READ 1
20 066555-000 LABEL-DO NOT ADJUST 2 20 066555-000 LABEL-DO NOT ADJUST 2
21 063423-000 LABEL-BRAKE RELEASE 1 21 063423-000 LABEL-BRAKE RELEASE 1
22 066562-001 LABEL-TIRE PSI 75 1 22 066562-001 LABEL-TIRE PSI 75 1
23 061515-000 LABEL-LIFT HERE 1 23 061515-000 LABEL-LIFT HERE 1
24 066568-000 LABEL-WARNING 1 24 066568-000 LABEL-WARNING 1
25 027898-000 LABEL-DIESEL FUEL 1 25 027898-000 LABEL-DIESEL FUEL 1
26 066557-013 LABEL-MAX LOAD 1750 LBS 2 26 066557-006 LABEL-MAX LOAD 1250 LBS 2
27 061683-004 LABEL-UPRIGHT 2 1/2 1 27 061683-004 LABEL-UPRIGHT 2 1/2 1
28 061683-005 LABEL-UPRIGHT 4 1/2 3 28 061683-005 LABEL-UPRIGHT 4 1/2 3
29 061683-007 LABEL-UPRIGHT 5 1/2 1 29 061683-007 LABEL-UPRIGHT 5 1/2 1
30 067644-002 LABEL-LX31 2WD 3 30 067644-004 LABEL-LX41 2WD 3
31 067644-001 LABEL-LX31 2WD 3 31 067644-003 LABEL-LX41 2WD 3
33 011248-004 NUT HEX ESNA 1/4-20UNC 4 33 011248-004 NUT HEX ESNA 1/4-20UNC 4
34 067538-000 LABEL BI-ENERGY 2 34 067538-000 LABEL BI-ENERGY 2
35 011525-008 SCREW HHC 1/4-20UNC X 1 4 35 011525-008 SCREW HHC 1/4-20UNC X 1 4
36 065368-000 TACK 4 36 065368-000 TACK 4
37 060830-000 SAFETY WALK 4 37 060830-000 SAFETY WALK 4
38 066561-001 LABEL, MAINT. BRACE 1 38 066561-001 LABEL, MAINT. BRACE 1
39 060086-000 SAFETY WALK 20 X 32 12 39 060086-000 SAFETY WALK 20 X 32 12
40 066558-000 LABEL, EMERG. LOWERING 2 40 066558-000 LABEL, EMERG. LOWERING 2
41 068641-003 LABEL, PARKING BRAKE 1 41 068641-003 LABEL, PARKING BRAKE 1

6-80 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Label Kit/Installation, LX41

067361-021/022
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-81

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
German Label Kit/Installation, German Label Kit/Installation,
LX31 Bi-Energy - Dual Deck LX41 Bi-Energy - Dual Deck
067361-024 067361-025
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.
1 010076-000 MANUAL CASE 1 1 010076-000 MANUAL CASE 1
3 067449-020 USER MANUAL LX-SERIES 1 3 067449-020 USER MANUAL LX-SERIES 1
4 064917-000 LABEL-HYD. FLUID 1 4 064917-000 LABEL-HYD. FLUID 1
5 061205-001 NAME PLATE EURO 1 5 061205-001 NAME PLATE EURO 1
7 067822-001 LABEL-GLOW INST. 1 7 067822-001 LABEL-GLOW INST. 1
8 067365-100 LABEL-LOWER CONTEOLLER 1 8 067365-100 LABEL-LOWER CONTEOLLER 1
10 064444-000 LABEL-USA 4 10 064444-000 LABEL-USA 4
11 067642-205 LABEL-CONTROLLER 1 11 067642-205 LABEL-CONTROLLER 1
12 064941-003 LABEL MOTOR CONTROLS 1 12 064941-003 LABEL MOTOR CONTROLS 1
13 064941-002 LABEL PLATFORM CONTROLS 1 13 064941-002 LABEL PLATFORM CONTROLS 1
14 064935-000 LABEL DANGER 1 14 064935-000 LABEL DANGER 1
17 062562-102 LABEL BATTERY 120LBS / 54Kg 1 17 062562-102 LABEL BATTERY 120LBS / 54Kg 1
23 064937-000 LABEL-LIFT HERE 1 23 064937-000 LABEL-LIFT HERE 1
26 064910-016 LABEL-MAX LOAD 1750LB / 795KG 2 26 064910-010 LABEL-MAX LOAD 1250LB / 563KG 2
27 061683-004 LABEL-UPRIGHT 2-1/2 1 27 061683-004 LABEL-UPRIGHT 2-1/2 1
28 061683-005 LABEL-UPRIGHT 4 1/2 2 28 061683-005 LABEL-UPRIGHT 4 1/2 2
29 061683-007 LABEL-UPRIGHT 5 1/2 1 29 061683-007 LABEL-UPRIGHT 5 1/2 1
30 067644-002 LABEL-LX31 2WD x 4 1/2” 3 30 067644-004 LABEL-LX41 2WD x 4 1/2” 3
31 067644-001 LABEL LX31 2WD x 6 1/2” 3 31 067644-003 LABEL LX41 2WD x 6 1/2” 3
32 030768-001 LABEL CE 1 32 030768-001 LABEL CE 1
33 011248-004 NUT HEX ESNA 1/4-20UNC 4 33 011248-004 NUT HEX ESNA 1/4-20UNC 4
34 067538-000 LABEL BI-ENERGY 2 34 067538-000 LABEL BI-ENERGY 2
35 011252-008 SCREW HHC 1/4-20UNC X 1 2 35 011252-008 SCREW HHC 1/4-20UNC X 1 2
36 065368-000 TACK 4 36 065368-000 TACK 4
37 060830-000 SAFETY WALK 4 37 060830-000 SAFETY WALK 4
39 060086-000 SAFETY WALK 20 X 32 12 39 060086-000 SAFETY WALK 20 X 32 12
40 064912-002 LABEL, EMERG. LOWERING 2 40 064912-002 LABEL, EMERG. LOWERING 2

6-82 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1

Label Kit/Installation, LX41

067361-024/025
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-83

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Valve Block Assembly, LX31/41
067389-000
ITEM PART DESCRIPTION QTY.
1 STEERING SOLENOID 2
2 STEERING RELIEF VALVE 1
3 LIFT RELIEF VALVE 1
4 FLOW CONTROL VALVE 1
5 DUMP VALVE 1
6 LIFT SOLENOID 1

Valve Block Assembly

067389-000
Drawing 1 of 1

6-84 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1
Brake Valve Block Assembly, LX31/41
068324-002
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.

1 068481-000 VALVE BLOCK, BRAKE 1 9 012004-006 PLUG #6 2

2 068553-000 VALVE, POPPET N.C. 48VDC 1 10 005135-000 STEEL BALL, 5/16” DIA. 1
3 068674-000 VALVE, POPPET N.O. 48VDC 1 11 013987-009 SPRING, 1/4 DIA. X 19/32 LG. 1
4 063965-001 PLUG, GUAGE PORT 1 12 012004-004 PLUG, #4 SAE 1
5 015919-002 ORIFICE, CESSNA 815 1 13 014021-005 PIPE NIPPLE 1/2” SCH 40 X 2 1/2” LG. 1
6 063921-010 PRESSURE SWITCH, 1 14 011920-002 PLUG,PIPE SOC HD 1/4-18 NPTF 1
7 011934-003 STR. ADAPTER #6MB - #6MJ 1 15 068798-001 SPRING 3/8 OD .035WIRE X 1 1/4 LG 1
8 011934-026 ELBOW 90ø #4MB - #4MJ 1 16 011934-004 ELBOW 90ø #6 SAE - #6 JIC 1

Brake Valve Block Assembly

068324-002
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-85

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Slide-Out Deck Installation, LX31/41
067866-001
ITEM PART DESCRIPTION QTY. ITEM PART DESCRIPTION QTY.

2 067787-001 SLIDE-OUT DECK WELDMENT 1 *23 011254-006 SCREW HHC 3/8-16UNC X 3/4 8
3 067760-002 WHEEL, SLIDE-OUT DECK 2 24 015936-014 SCREW SHOU 3/8-16UNC X 1 3/4 12
4 066193-000 STOP 2 25 011254-032 SCREW HHC 3/8-16UNC X 4 4
5 067720-000 ROLLER 2 26 067920-000 SPACER, GUARDRAIL 2
6 067818-001 ARM, CABLE GUIDE 2 27 060086-000 SAFETY WALK (20 X 32) 4
7 067786-001 BRACKET, CABLE GUIDE 1 28 066557-001 LABEL, PLATFORM CAPY 1
8 067761-000 PIVOT, PUSH BAR 2 29 067867-001 ROLLER BRACKET REAR WELDMENT L.H. 1
9 067862-003 HANDLE WELDMENT 2 30 067867-000 ROLLER BRACKET REAR WELDMENT R.H. 1
10 066170-002 WEAR PAD 2 31 063666-004 WIRE CHANNEL 1
11 067776-001 GUARDRAIL WELDMENT 2 32 011253-012 SCREW HHC 5/16-18 X 1 1/2 2
12 067778-000 GUARDRAIL WELDMENT 1 33 011248-005 NUT HEX 5/16-18 ESNA 2
13 067755-001 SWING TUBE 2 34 011240-005 WASHER 5/16 FLAT STD 4
14 011848-038 CLEVIS PIN, 1/2” DIA X 2 1/2 2 35 010414-000 LOCKING PIN ASSY 5/16 N 1
15 026553-008 RIVET POP N 3/16 X (.5-.63 GRIP) 4 36 066556-000 LABEL, WARNING DESEND PLTFM 2
16 011757-005 COTTER PIN, RUE RING 2 38 066198-000 WEAR PAD 2
17 014996-006 WASHER, FLAT 3/8” DIA 42 39 011252-012 SCREW HH 1/4-20 X 1 1/2 4
18 067695-000 SPACER 4 40 011248-004 NUT 1/4-20 ESNA 4
19 011248-006 LOCKNUT, 3/8-16UNC ESNA 34 41 015770-099 HOSE 3/8 DIA X 1 1/2 LG 4
20 012865-099 LOOM, WIRE 3/4” 1FT 42 067783-003 ROLLER BRACKET R.H. 2
21 011254-008 SCREW HHC 3/8-16UNC X 1 10 43 067783-004 ROLLER BRACKET L.H. 2
22 011254-014 SCREW HHC 3/8-16UNC X 1 3/4 4 * Not Shown

Slide-Out Deck Installation

067866-001
Drawing 1 of 1

6-86 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1
Amber Beacon Option, LX31/41
067947-000
ITEM PART DESCRIPTION QTY.
1 012848-004 LIGHT 12-24 VOLT 2
2 063193-000 LIGHT BRACKET 2
3 029702-000 FUSE HOLDER 1
4 029704-002 FUSE 2 AMP 1
5 029610-002 CONN. FORK 16-14 #8 1
6 029601-013 CONN. RING 16-14 #10 1
7 029620-002 CONN. BUTT 16-14 4
8 029496-099 WIRE 16 AWG 2 COND 18FT
9 011249-003 NUT HEX ESNA #10-32 4
10 011826-004 SCREW MACH. RD. HD. #10-32 X 1/2 4

Amber Beacon Option

067947-000
Drawing 1 of 1

LX31/41 Electric/Bi-Energy Work Platform 6-87

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Horn Option, LX31/41
067908-000
ITEM PART DESCRIPTION QTY.
1 011252-008 SCREW HHC 1/4-20 X 1 2
2 011248-004 NUT HEX 1/4-20 2
3 029452-099 WIRE 16 GA BLACK 75FT
4 067902-000 BRACKET, GAS SPRING 1
5 029610-002 CONNECTOR FORK 3
6 029601-014 CONNECTOR RING 1
7 029615-002 CONNECTOR PUSH 2
8 029958-001 HORN 24VDC 1
9 063917-000 SWITCH PUSHBUTTON 1
11 011248-005 NUT HEX ESNA 5/16-18 1
12 011253-008 SCREW HHC 5/16-18UNC X 1 1

Horn Option
067908-000
Drawing 1 of 1

6-88 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1
Motion Alarm Option, LX31/41
067909-000
ITEM PART NO DESCRIPTION QTY
1 029452-099 WIRE 16 GA BLK FT 2
2 029610-002 TERMINAL #8 FORK 4
3 029825-002 DIODE 3 AMP 3

LX31/41 Electric/Bi-Energy Work Platform 6-89

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN
Poly Fill Tire Option, LX31/41 2 Wheel Drive
067910-001
ITEM PART DESCRIPTION QTY.
1 067665-005 POLY FILL TIRE & WHEEL ASSY-FRONT 2
2 068327-003 POLY FILL TIRE & WHEEL ASSY-REAR 2

067665-005
ITEM PART DESCRIPTION QTY.
1 067609-001 WHEEL, 16.5 X 8.25 8 HOLE, 8 BC 1
2 068555-000 TIRE, 9.5 X 16.5 NHS 10 PLY 1
3 012282-001 VALVE STEM 1

068327-003
ITEM PART DESCRIPTION QTY.
1 067609-000 WHEEL, 16.5 X 8.25 6 HOLE ON 6” 8 B.C. 1
2 068555-000 TIRE, 9.5 X 16.5 10 PLY 1
3 012282-001 VALVE STEM 1

6-90 LX31/41 Electric/Bi-Energy Work Platform

 Section
ILLUSTRATED PARTS BREAKDOWN 6.1
Removable Controller Option, LX31/41
061898-002
ITEM PART DESCRIPTION QTY.
1 028800-003 PLUG CONNECTOR (FEMALE) 1
2 028800-004 PIN CONTACT (MALE) 15
3 028800-015 PLUG SEALING 16
4 028800-016 RECEPTACLE CONNCTOR W/CLAMP (MALE) 1
5 028800-005 SOCKET CONTACT (FEMALE) 15
8 030719-001 110 VAC BRACKET 1
10 011254-020 SCREW HHC GRD5 3/8-16UNC X 2 1/2 2
11 011240-006 WASHER 3/8 STD FLAT 4
12 011248-006 NUT HEX ESNA 3/8-16 2
13 068761-000 LOCKING WEDGE-CONN 1
14 068760-001 CONNECTOR-RECEPTACLE 1
15 068762-000 PIN-CONTACT 9
16 068761-001 LOCKING WEDGE-CONN 1
17 068760-000 PLUG-CONNECTOR 1
18 068762-001 SOCKET-CONTACT 9
19 068764-000 PLUG-CONNECTOR 6
20 068908-000 BOOT ELECT. PLUG 1
21 068908-001 BOOT ELECT. RECEPTACLE 1

Removable Controller Option

067898-002
Drawing 1 of 2

LX31/41 Electric/Bi-Energy Work Platform 6-91

 Section
6.1 ILLUSTRATED PARTS BREAKDOWN

Removable Controller Option

067898-002
Drawing 2 of 2

6-92 LX31/41 Electric/Bi-Energy Work Platform

 Call Toll Free in U.S.A.
1-800-926-LIFT
For Parts:
UpRight, Inc. 1-888-UR-PARTS UpRight Ireland, Ltd.
1775 Park Street Pottery Road
Selma, California 93662 Dun Laoire
TEL: 559/891-5200 Ireland
FAX: 559/891-9012 TEL: +353-1-202-4100
PARTS FAX: 559/896-9244 FAX: +353-1-202-4105

067448-020
B 9/99 K