WACKER® AK 12 500
SILICONE FLUID
Product description - antifoam agent
- water-repellent agent
Structural formula: - liquid dielectric for electrical and electronic
equipment
- polish additive
- plastics additive
- additive for textile and fiber auxiliaries
- damping medium
For pharmaceutical applications, we recommend
specialty silicone fluids from our SILFAR ® line.
Silicone fluids from our BELSIL ® line are available for
the cosmetic sector. Whenever particularly high heat
and shear resistance is required, we recommend
silicone fluids from our AK stab, AK visc and AKC
product lines.
Processing
WACKER® AK 12 500 is a linear, non-reactive
polydimethylsiloxane with a viscosity of Due to WACKER® AK 12 500 many diverse
approx. 12 500 mm²/s. Due to its chemical structure, applications, no general processing information can be
WACKER® AK 12 500 has an outstanding property provided. Parameters will vary from application to
profile, which sets it apart from organic materials such application.
as mineral oils.
Available in a range of viscosities,
Properties WACKER® SILICONE FLUIDS AK are miscible with
each other in any ratio. The standard product's
WACKER® AK 12 500 is a clear, odorless and viscosity can thus be altered to suit your individual
colorless liquid. needs.
WACKER® AK 12 500 is a non-polar liquid and is
Special features immiscible with polar solvents such as water or short-
chain alcohols. In aliphatic and aromatic hydrocarbons,
- minimal change in physical properties over a broad chlorohydrocarbons, ethers, esters, ketones and
temperature range higher alcohols, WACKER® AK 12 500 is soluble in
- excellent water-repellent properties any proportion.
- good dielectric properties Before the product is used with solvents for the first
- low surface tension and thus high surface activity time, it is advisable to perform a lab-scale test.
- chemically highly unreactive When solvents are used, please remember to read the
- low solidifying point appropriate hazard information.
- high flash point
- high heat resistance
- good solubility in a wide range of solvents Storage
Maximum temperature allowed during storage and
Application transportation:
50 °C
- release agent The 'Best use before end' date of each batch is shown
- lubricant on the product label.
- hydraulic fluid
Technical data sheet for WACKER® AK 12 500 / Version: 1.3 / Date of last alteration: 06.11.2014 1/2
Storage beyond the date specified on the label does
not necessarily mean that the product is no longer Safety notes
usable. In this case however, the properties required
for the intended use must be checked for quality Comprehensive instructions are given in the
assurance reasons. corresponding Material Safety Data Sheets. They are
available on request from WACKER subsidiaries or
may be printed via WACKER web site
http://www.wacker.com.
Product data
Typical general characteristics Inspection Method Value
Appearance colorless, clear
Viscosity, kinematic at 25 °C DIN 53019 approx. 12500 mm²/s
Density at 25 °C DIN 51757 approx. 0,97 g/cm³
Refractive index at 25 °C approx. 1,404
Flash point ISO 2592 359 °C
Surface tension at 25 °C approx. 0,022 N/m
Ignition temperature (liquids) DIN 51794 approx. 450 °C
These figures are only intended as a guide and should not be used in preparing specifications.
The data presented in this medium are in accordance with the present state of our knowledge but The management system For technical, quality, or
do not absolve the user from carefully checking all supplies immediately on receipt. We reserve the has been certified product safety questions,
right to alter product constants within the scope of technical progress or new developments. The according to please contact:
recommendations made in this medium should be checked by preliminary trials because of DIN EN ISO 9001 and
conditions during processing over which we have no control, especially where other companies’ DIN EN ISO 14001 Wacker Chemie AG
raw materials are also being used. The information provided by us does not absolve the user from Hanns-Seidel-Platz 4
the obligation of investigating the possibility of infringement of third parties’ rights and, if necessary, WACKER® is a trademark 81737 München, Germany
clarifying the position. Recommendations for use do not constitute a warranty, either express or of info.silicones@wacker.com
implied, of the fitness or suitability of the product for a particular purpose. Wacker Chemie AG.
www.wacker.com
Technical data sheet for WACKER® AK 12 500 / Version: 1.3 / Date of last alteration: 06.11.2014 2/2
