Catnic

International Product Catalogue

October 2007
 Quality Building Products

Catnic is a leading supplier and manufacturer of building products for the

construction industry. Acknowledged for our excellence of service and conformance
to the highest quality standards, our products have been installed successfully in
municipal buildings and domestic properties in over 30 countries worldwide.

Building on our strength in the steel lintels market, Catnic also supply a
comprehensive range of branded building components and plasterers’ profiles which
are manufactured to the same industry-leading high standards as our renowned
steel lintels. Selecting the Catnic brand assures that the products you have chosen
are of superior quality and are fully supported by our extensive distributor network.

If you need details of your local distributor,

or if you require any further information please contact.

International Sales Dept.

Catnic – Corus (UK) Ltd
Pontypandy Estate
Caerphilly
United Kingdom
CF83 3GL

Tel +44 (0) 29 2033 7900

Fax +44 (0) 29 2088 0855

Website: www.catnic.com

ISO 9001

2 Catnic International
Contents

L I N T E L S

Steel Lintels 4

P L A S T E R A C C E S S O R I E S

Installation guide 12

Beads
Galvanised 14
Stainless Steel 23
PVC nosed 27
PVC 29

Expanded metal
Lath and Riblath 30
Arch formers 32
Coil Mesh for Blockwork 34

W A L L A C C E S S O R I E S

Wall Ties 36
Wall Connectors 37
Brick and Block spacer system 38

F E N C E P O S T S Y S T E M S

QwikPost 41

Catnic International 3
 Design Features
Lintels should be installed with a 20cm bearing at each end and should be fully
bedded on blockwork mortar. Our Technical Department should be consulted if
bearings less than 20cm are required.

Features & Benefits

Catnic Steel Lintels provide a combination of strength and light weight resulting
in efficient loadbearing performance and increased productivity on site

> No need for lifting equipment as two men can lift even the longest length
into position.
> No delay to blockwork, it can be continued immediately.
> No propping required while waiting for concrete to cure.
> Corrosion protected.
> Safe Working Loads are all given in the tables provided and have been
substantiated by independent testing.
> Efficient plaster key.
> Brackets for column fixing provide considerable time savings.

Specifications
Corrosion Protection System

In addition to the use of high quality galvanised steel, the lintels are further
protected against corrosion by the addition of a thermosetting polyester powder
coating. This coating is applied by an electrostatic process that ensures close
control over quality and thickness of coating.

This duplex system of an organic coating over galvanised steel provides excellent
long-term resistance to the corrosive elements present in all building situations.

NOTE:
Lintels type CN92 and CN102 are designed for internal use only and are supplied
without powder coating.

4 Catnic International
 Quality Assurance
Catnic steel lintels are made to the highest quality standards.

> The steel used in their manufacture is in accordance with

BSEN 10327:2004-DX51D+Z275
> Lintels conform to the specifications laid down in BS 5977: Part 2: 1983.
> Catnic was the first lintel manufacturer to be awarded a kitemark symbol
and the range is identified with the symbol in this brochure.

BSI licences the use of the kitemark only after:

> It has independently tested the products and is satisfied that it conforms with
the BS specification.
> It has visited and assessed the manufacturer to ISO 9001 and is satisfied that
the quality control systems used ensure that the product continues to conform
to specifications.

ISO 9001
Technical Advisory Service

A comprehensive scheduling service is offered without charge or obligation. Simply

send us a set of drawings (plans, sections and elevations) for any size project and
we will provide you with a comprehensive schedule of requirements.
In addition to the range shown in this catalogue many other sizes and types are
available upon request.

Installation

> Damaged lintels should not be used.

> 20cm end bearing should be allowed at each side.
> Lintels should not be cut down from manufactured lengths without prior
approval.
> If you have any doubt concerning any installation, please contact Catnic
for advice.
> For cavity lintels, the inner and outer leaves must be raised together.

Plaster Key

> Generally lintels are supplied with perforations as a plaster key but
occasionally it may be necessary to supply expanded mesh fixed to
the lintels as an alternative.

This brochure is copyright, the copyright being

owned by Catnic – Corus UK Limited and the
unauthorised reproduction of the whole or part of
it is prohibited.

© Catnic – Corus UK Limited 2007

Catnic International 5
 Catnic lintel installation
TOTAL Installation Time – 2 minutes

Comparison of installation times

of a Catnic lintel and a conventional
concrete cast in-situ lintel.

1 2 3

Concrete cast in-situ lintel installation

TOTAL Installation Time – 48 minutes. The concrete lintel must be left to cure before
continuing with blockwork installation.

1 Vertical framework 2 Commencement of lintel 3 Continuation of

erected and secured and framework. framework.
a horizontal level taken.

WAIT!

4 Completion of 5 Completion of lintel 6 Wait for concrete to set

framework. after steel reinforcement
and pouring of concrete.

In the time taken to install just one concrete lintel,

TWENTY FOUR Catnic lintels could have been
installed.

6 Catnic International
Channel Lintels for Solid Walls

Lintel Profiles – dimensions in mm.

75 75
50 50

103 CN100 103 CN103 153 CN150 153 CN152

LINTEL TYPE/CODE CN100 CN103 CN150 CN152

Gauge Code A B C C A B C C

Sheet Thickness (mm) 2.0 2.5 3.1 3.1 2.0 2.5 3.1 3.1

Weight per metre (kg) 3.0 3.7 4.7 5.9 3.7 4.7 5.9 7.1

Safe working load uniformly distributed (tonnes)

Lengths available (m) 0.90 – 1.20 0.55 0.80 1.12 1.63 0.48 0.76 1.22 1.63

in increments of 0.1m 1.30 – 1.50 0.42 0.58 0.66 1.25 0.37 0.58 0.79 1.25

1.60 – 1.80 0.31 0.38 0.44 1.00 0.27 0.41 0.52 1.00
1.90 – 2.10 – 0.24 0.31 0.86 – 0.27 0.37 0.86

2.20 – 2.40 – 0.18 0.23 0.64 – 0.19 0.28 0.64

2.50 – 2.70 – – 0.16 0.47 – – 0.19 0.47

2.80 – 3.00 – – 0.13 0.38 – – 0.14 0.38

Lintel Profiles – dimensions in mm.

75
50 50

203 CN200 203 CN202 253 CN250

LINTEL TYPE/CODE CN200 CN202 CN250

Gauge Code A B C C A B C

Sheet Thickness (mm) 2.0 2.5 3.1 3.1 2.0 2.5 3.1

Weight per metre (kg) 4.4 5.6 7.1 8.5 5.4 6.7 8.6

Safe working load uniformly distributed (tonnes)

Lengths available (m) 0.90 – 1.20 0.62 0.77 1.05 1.63 0.62 0.77 1.05

in increments of 0.1m 1.30 – 1.50 0.48 0.59 0.80 1.25 0.48 0.59 0.80

1.60 – 1.80 0.35 0.41 0.53 1.00 0.35 0.41 0.53

1.90 – 2.10 – 0.29 0.38 0.86 – 0.29 0.38

2.20 – 2.40 – 0.21 0.28 0.64 – 0.21 0.28

2.50 – 2.70 – – 0.19 0.47 – – 0.19

2.80 – 3.00 – – 0.14 0.37 – – 0.14

Note Width dimensions are ‘inside of channel’ dimensions.

Catnic International 7
Box Lintels for Solid Walls

Lintel Profiles – dimensions in mm.

WALL WIDTH LINTEL TYPE GAUGE CODE STEEL THICKNESS WEIGHT SAFE WORKING LENGTHS AVAILABLE
(mm) (kg per metre) Load (tonnes) (metres)

100mm CN5X A 2.0 7.6 2.0 1.05 to 2.70 except

1.35 in 150mm increments

100mm CN6X B 2.5 12.4 3.0 2.85, 3.00, 3.30, 3.60

100mm CN6X C 3.1 15.7 3.0 3.90, 4.20

Lintel Profiles – dimensions in mm.

WALL WIDTH LINTEL TYPE GAUGE CODE STEEL THICKNESS WEIGHT SAFE WORKING LENGTHS AVAILABLE
(mm) (kg per metre) Load (tonnes) (metres)

140/150mm CN56X A 2.0 9.0 2.0 1.05 to 2.70 except

1.35 in 150mm increments

140/150mm CN66X B 2.5 14.1 3.0 2.85, 3.00, 3.30, 3.60

140/150mm CN66X C 3.1 18.0 3.0 3.90, 4.20

Lintel Profiles – dimensions in mm.

WALL WIDTH LINTEL TYPE GAUGE CODE STEEL THICKNESS WEIGHT SAFE WORKING LENGTHS AVAILABLE
(mm) (kg per metre) Load (tonnes) (metres)

190/200mm CN19/14 A 2.0 2.0 2.0 10.0 2.0 1.05 to 2.10

in 150mm increments

190/200mm CN19/19 B 2.5 2.5 2.0 13.8 3.0 2.25 to 3.00

in 150mm increments

190/200mm CN19/19 C 3.1 3.1 2.0 16.8 3.0 3.30, 3.60, 3.90, 4.20

All lintels illustrated are supplied fully perforated (except top surface) as standard.

8 Catnic International
Lintels for Cavity Walls

Lintel Profiles – dimensions in mm.

WALL WIDTH LINTEL TYPE GAUGE CODE STEEL THICKNESS WEIGHT SAFE WORKING LENGTHS AVAILABLE
(mm) (kg per metre) Load (tonnes) (metres)

200mm CN71 A 2.0 2.0 1.6 9.3 2.0 1.05 to 2.70 (except 1.95,
2.25) in 150mm increments

200mm CN81 B 2.5 2.5 2.0 15.1 3.0 3.00, 3.30, 3.60

200mm CN81 C 3.1 3.1 2.0 18.5 3.0 3.90, 4.20

For 50-65mm Cavity 100-115mm Inner Leaf

100 48 95

nominal 521/05GC
height ‘h’
(see tables
below)

CG

001/05-H/GC
CG50/100
STANDARD LENGTHS (MM) 750-1500 1650-1800 1950-2100 2250-2400 2550-2700 2850-3000 3300-3900

SWL 1:1/3:1 (kN) 15 18 20 22 26 26 26

Weight 5.80 7.34 7.96 8.59 9.84 12.29 16.02

Nominal height ‘h’ (mm) 140 140 160 180 220 220 220

521/07GC
For 50-65mm Cavity 125-140*mm Inner Leaf

125 48 95

nominal
height ‘h’
521/05GC
(see tables 001/05-UC
below)

CG

521/05-H/GC
CG50/125*
521/09GC
STANDARD LENGTHS (MM) 750-1200 1350-1800 1950-2400 2550-2700 2850-3000

SWL 1:1/3:1 (kN) 12 17 20 26 26

Weight 6.3 7.78 9.03 12.87 16.55

Nominal height ‘h’ (mm) 140 140 180 220 220

521/07GC

001/05-EGC

521/05-UC

521/09GC
Catnic International 9
Lintels for Internal Partitions

Lintel Profiles - dimensions in mm.

75 100

25 25

68 98
CN92 CN102

WALL WIDTH LINTEL TYPE GAUGE CODE STEEL THICKNESS WEIGHT SAFE WORKING LENGTHS AVAILABLE
(mm) (kg per metre) Load (tonnes) (metres)

75mm CN92 1.2 1.2 0.7 1.05 & 1.20

100mm CN102 1.2 1.8 0.7 1.05 & 1.20

Catnic corrugated lintels CN92 and CN102 are designed for internal partition walls only and are manufactured from galvanised steel to
BSEN 10327:2004-DX51D+Z275.

These lintels are supplied in plain galvanised steel without powder coating.

NOTE: When using these lintels normal building practice should be observed, in that one course of blockwork (Nominal height 200mm)
should be laid on the lintel and the mortar allowed to harden for at least 24 hours before additional loads are applied.

10 Catnic International
Lintel Brackets

External Application
Unperforated

Brackets are supplied with fixing holes to suit metal expansion

Perforated
anchor sizes specified in table below.

CODE REFERENCE SUITABLE FOR LINTELS MAXIMUM LOAD TONNES/BRACKET

SB 02/15P * 0.45 – 0.72 –

CN56X, CN66X
SB 02/15P/A1 * – 0.72 – 0.72

SB 02/19P * 0.50 – 0.88 –

CN71, CN81, CN19/14, CN19/19
SB 02/19P/A1 * – 0.88 – 0.90

SB 02/24P * 0.50 – 0.88 –

CN7, CN8
SB 02/24P/A1 * – 0.88 – 1.04

SB 02/28P * 0.50 – 0.88 –

CN11, CN12
SB 02/28P/A1 * – 0.88 – 1.15

Metal expansion anchors quantity - diameter (mm) 2 No. M8 2 No. M10 4 No. M8 4 No. M10

* Unperforated brackets can be supplied on request, simply delete “P” from code reference.

Internal Application

Brackets are supplied with fixing holes to suit metal expansion

anchor sizes specified in table below.

CODE REFERENCE SUITABLE FOR LINTELS MAXIMUM LOAD TONNES/BRACKET

SB 01 * CN5X, CN6X, CN100 0.50 – 0.80 –

SB 01/A1 * CN103, CN102 – 0.88 – 0.90

SB 03 * 0.50 – 0.80 –
CN150, CN152
SB 03/A1 * – 0.88 – 0.90

SB 08 * CN200, CN202 0.50 – 0.77 –

Metal expansion anchors quantity - diameter (mm) 2 No. M8 2 No. M10 4 No. M8 4 No. M10

Catnic International 11
 Plaster Accessories
Our comprehensive range of Plaster Accessories are
precision engineered and simple to use. Fixing
by nail or plaster dab is straightforward and fast,
generating arises, edges, corners and joints that are
easy to form and resistant to chipping, cracking and
impact damage.

12 Catnic International
How to Install a Catnic Plasterer’s Bead
The most appropriate Catnic bead should be chosen to suit the b) Pressing the bead onto dabs of the same material as the
application, required plaster depth and the desired finish of the work. undercoat. Dabs should be applied at a maximum of 600mm

The application and installation of Catnic beads should be in apart. This method will even out minor irregularities in the line of

accordance with BS 5492:1990 Code of Practice for internal the background, although the line of the bead will tend to generally

plastering and BS 5262:1991 Code of Practice for external follow the line of the background.

renderings.
Block
Beads may be trimmed to length using tinman’s shears across the
wings and a fine toothed saw across bead noses.

Use one of the following methods to fix Catnic angle beads and
plaster stop beads: Concrete dabs 600mm apart (max)
(DABS NOT SHOWN TO SCALE IN
RELATION TO BEAD).
a) Using galvanised or stainless steel nails (compatible with bead
Bead
material) complying with BS 1202: Part 1, fixed at a maximum of
600mm apart. When nailing to a solid background the line of the
Plaster
bead will follow the line of the background.

Bead
Block c) When beads are used with metal lath backgrounds,
galvanised or stainless steel tying wire may be used to
secure the beads in position. Soft galvanised wire to BS
443 and soft stainless steel wire complying with BS 1554
should be used to match the bead and lath materials. All
Nails 600mm
apart (max) wires should be twisted tightly and the ends bent away
from the finished face of the coating.

Plaster

Corrosion Protection – Plaster Accessories

In normal circumstances, matured plasterwork may be In external applications and, in conditions where heavy
regarded as dry and therefore non-corrosive. Risks of corrosion condensation, persistent damp or regular exposure to moisture
in galvanised accessories only normally become apparent are likely, stainless steel, PVC-U or PVC-U nosed products
during the initial plaster drying out period, which should be should be specified.
kept to a minimum, and subsequently during periods of heavy
condensation. In general, care should be taken to ensure that metal
accessories are kept dry and distortion is prevented during
The use of sand or water contaminated with soluble salts in storage and handling. Care should also be taken to prevent
plastering mixes should be avoided as should soluble chlorides mechanical damage to the galvanised coating.
as they are likely to increase the risk of metal corrosion. The
presence of sea salts in sand used in plastering which is in Stainless steel products are for use specifically with cement
contact with galvanised accessories will often cause rust based renders. Contact our Technical Services Department
staining and should therefore be avoided. if considering the use of stainless steel beads with Gypsum
plaster.

Catnic International 13
Catnic Galvanised Beads
Angle Beads

Application
Angle beads provide true and straight corners which are resistant to chipping and cracking
giving strength and protection against everyday knocks.

Fixing
Fix either by nailing or using plaster dabs as shown in the illustration above.

Quality
Manufactured from galvanised steel to BSEN 10327: 2004 – DX51D+Z275 or Stainless Steel
to BSEN 10088-2-1.4301. All beads shown are manufactured in accordance with BS 6452:
Part 1: 1984.

7.5mm 7.5mm 13mm

12mm 12mm 5mm

38mm
34mm
34mm

CHISEL NOSE ANGLE BEAD ROUND NOSE ANGLE BEAD AB 38

Ref: 4000 4001 AB38

Lengths: 3.0m 3.0m 3.0m

Packing: Shrink film Euro packaged, 25 lenghts/pack Shrink film Euro packaged, 25 lenghts/pack 50 lengths/pack

Angle Bead

14 Catnic International
Catnic Galvanised Beads
Angle Beads
12 - 19mm
13mm 12 - 19mm

5mm 5mm 5mm

53mm 65mm
45mm

SUPASAVE ANGLE BEAD STANDARD ANGLE BEAD WIDE WING ANGLE BEAD

Ref: SS STD WW 3.0

Lengths: 2.4m, 2.7m, 3.0m 2.4m, 2.7m, 3.0m 3.0m

Packing: 50 lengths/pack 50 lengths/pack 50 lengths/pack

90º

7mm 3mm 10mm 4mm 9.5mm

10mm

30mm 40mm 30mm

Ø5mm

SQUARE HOLE ANGLE BEADS SQUARE HOLE ANGLE BEADS SQUARE HOLE ANGLE BEADS
Small Nose Small Nose Round Nose

Ref: 4004 4005 4006

Lengths: 2.5m, 3.0m 2.5m, 3.0m 2.5m, 3.0m

Packing: Shrink film Euro packaged Shrink film Euro packaged Shrink film Euro packaged
25 lengths/pack 25 lengths/pack 25 lengths/pack

Square Hole Angle Bead with PVC Nose Square Hole Angle Bead

Catnic International 15
Catnic Galvanised Beads
Plasterstop

Application
Plaster stop beads provide clean, neat edges at openings or abutments onto other wall
surfaces or ceiling finishes. Available to suit plaster thicknesses of 10/13/16/19mm.

Fixing
Fix either by nailing or using plaster dabs as shown in the illustration above.

Quality
Manufactured from galvanised steel to BSEN 10327: DX51D+Z275. All beads shown are
manufactured in accordance with BS 6452: Part 1: 1984.

57mm
58mm 55mm 60mm 3mm
3mm 3mm 3mm

Ø4.7mm
Ø4.7mm Ø4.7mm Ø4.7mm

19mm
10mm 13mm 16mm

PLASTERSTOP BEAD

Ref: PS10 PS13 PS16 PS19

Lengths: 3.0m, 2.7m, 2.4m 3.0m, 2.7m, 2.4m 3.0m, 2.7m, 2.4m 3.0m, 2.7m, 2.4m

Packing: 50 lengths/pack 50 lengths/pack 50 lengths/pack 50 lengths/pack

Plasterstop Bead

16 Catnic International
Catnic Galvanised Beads
Plasterstop

53mm
53mm

53mm

galvanised - blue

galvanised - blue
aluminium - lighter grey
18mm 12mm
aluminium - lighter grey
stainless steel - blue green 8mm

stainless steel - blue green

PVC - white

PVC - white
plaster dark

plaster dark
plaster light

plaster light

PLASTERSTOP PUNCHED WING

Ref: 6212 6213 6214

Lengths: 2.5m, 3.0m 2.5m, 3.0m 2.5m, 3.0m

Packing: 25 lengths/pack 25 lengths/pack 25 lengths/pack

galvanised - blue galvanised - blue galvanised -

110º 110º
aluminium - lighter grey 110º
aluminium - lighter grey aluminium -

stainless steel - blue green stainless steel - blue green stainless ste
53mm 53mm 53mm

PVC - white PVC - white PVC - white

plaster dark plaster dark plaster dark

plaster light plaster light plaster light

13mm 9mm 18mm

PLASTERSTOP PUNCHED WING

Ref: 6215 6217 6219

Lengths: 2.5m, 3.0m 2.5m, 3.0m 2.5m, 3.0m

Packing: 25 lengths/pack 25 lengths/pack 25 lengths/pack

Catnic International 17
Catnic Galvanised Beads
Architrave

Application
Architrave beads give a shadow line decorative effect for aesthetic purposes and create a
clean division between varying wall finishes eg. at wall and ceiling abutments or door and
window reveals.

Fixing
Fix either by nailing or using plaster dabs.

Quality
Manufactured from galvanised steel to BSEN 10327:2004 – DX51D+Z275.
All beads shown are manufactured in accordance with BS 6452: Part 1: 1984.

13mm 20mm 20mm 20mm

10mm 13mm 13mm 10mm 13mm
13mm

37mm 37mm 37mm 37mm

37mm

ARCHITRAVE

Ref: ARC10/WF/3.0 ARC13/WF/3.0 ARC20/WF/3.0 ARC10/WO/3.0 ARC13/WO/3.0

Lengths: 3.0m 3.0M 3.0M 3.0M 3.0M

Packing: 25 lengths/pack 25 lengths/pack 30 lengths/pack 25 lengths/pack 25 lengths/pack

Architrave Bead

18 Catnic International
Catnic Galvanised Beads
Movement and Renderstop Beads

Application
Movement bead allows for movement between adjoining surface finishes resulting from
differential expansion or settlement.

Renderstop beads are used to obtain a neat, bell cast lower edge to external finishes and
helps to protect masonry against run-off water.

Fixing
Fix either by nailing or using plaster dabs.

Quality
Manufactured from galvanised steel to BSEN 10327: 2004-DX51D+Z275.
All beads shown are manufactured in accordance with BS 6452: Part 1: 1984.

19mm

12mm
(15mm, 18mm, 21mm)

7mm
45mm

25mm
60°
RS3.0
25mm

MOVEMENT BEAD RENDERSTOP BEAD

Ref: MB10, MB13, RS3.0

MB16, MB19

Steel finish: Galvanised with PVC-U strip Galvanised

Lengths: 3.0m 3.0m

Packing: 10 lengths/pack 50 lenghts/pack

Movement Bead Renderstop Bead

Catnic International 19
Catnic Galvanised Beads
Depth Guage Beads

Application
Provides a quick and accurate means of ensuring consistent, minimum plaster
depths as plaster is simply ‘ruled off’ to leave the required thickness.

Fixing
Fix using galvanised nails.

Quality
Manufactured from galvanised steel to BSEN 10327:2004-DX51D+Z275.

21mm 23mm

Ø5mm Ø5mm

6mm 10mm
Ø3mm Ø3mm

DEPTH GUAGE BEAD DEPTH GUAGE BEAD

Ref: 4100 4101

Lengths: 2.5m, 3.0m 2.5m, 3.0m

Packing: Shrink film Euro packaged, 25 lengths per pack Shrink film Euro packaged, 25 lengths per pack

Depth Guage Bead

20 Catnic International
Catnic Galvanised Beads
Drywall and Thin Coat Plaster Applications

Application
Drywall angle beads are designed for single/thin coat plasterwork, enabling a thin
coat finish of just 3mm.
Micromesh angle beads have fine mesh wings suitable for a single/thin coat of
6mm.

Fixing
Fix either by nailing or using plaster dabs.

Quality
Manufactured from galvanised steel to BSEN 10327:2004-DX51D+Z275. All beads
shown are manufactured in accordance with BS 6452: Part 1: 1984.

80° 85°

3mm 3mm 6mm

3mm

6mm 3mm
25mm
23mm

25mm

Ø4mm Ø4mm

DRYWALL ANGLE BEAD DRY WALL THIN COAT BEAD MICROMESH ANGLE BEAD

Ref: DW DWTC MM

Lengths: 2.4m, 3.0m 2.4M, 3.0M 2.4m, 3.0m

Packing: 50 lengths/pack 50 lengths/pack 50 lengths/pack

Drywall Angle Bead Micromesh Angle Bead

Catnic International 21
Catnic Galvanised Beads
Drywall and Thin Coat Plaster Applications

Application
Drywall stop beads provide abutments of thin coat (3 or 6mm) plastered areas to other wall
finishes. The scalloped edge provides efficient keying and excellent finish.
Plasterboard edging beads are used to reinforce plasterboard edges and can be
used either with perforated edges to take the final coat of plaster or reversed to take
a simple painted finish. Available for 10 or 13mm board thicknesses.

Fixing
Fix either by nailing or using plaster dabs.

Quality
Manufactured from galvanised steel to BSEN 10327: 2004-DX51D+Z275.
All beads shown are manufactured in accordance with BS 6452: Part 1: 1984.

12mm (15mm)
3mm (6mm) 12mm (10mm)

30mm

3mm

25mm
9.5mm
(12.5mm)

PBEB13
dimensions in
2mm
brackets.

DRYWALL STOP BEAD PLASTERBOARD EDGING BEAD

Ref: DWSB3, DWSB6 PBEB 10, PBEB 13

Lengths: 3.0m 3.0m

Packing: 50 lengths/pack 50 lengths/pack

Drywall Stop Bead Plasterboard Edging Bead

22 Catnic International
Catnic Stainless Steel Beads
Angle Beads

Application
Angle beads provide true and straight corners which are resistant to chipping and cracking
giving strength and protection against everyday knocks.

Fixing
Fix either by nailing or using plaster dabs as shown in the illustration.

Quality
Manufactured from stainless steel to BSEN 10088-2-1.4301.
All beads shown are manufactured in accordance with BS 6452: Part 1: 1984.

12 - 19mm

12 - 19mm

5mm 5mm

65mm
53mm

STANDARD ANGLE BEAD WIDE WING ANGLE BEAD

Ref: STD 3.0/SS WW 3.0/SS

Lengths: 3.0m 3.0m

Packing: 50 lengths/pack 50 lengths/pack

Angle Bead

Catnic International 23
Catnic Stainless Steel Beads
Plasterstop Beads

Application
Plaster stop beads provide clean, neat edges at openings or abutments onto other wall
surfaces or ceiling finishes. Available to suit plaster thicknesses of 10/13/16/19mm.

Fixing
Fix either by nailing or using plaster dabs as shown in the illustration above.

Quality
Manufactured from stainless steel to BSEN 10088-2-1.4301.
All beads shown are manufactured in accordance with BS 6452: Part 1: 1984.

57mm
58mm 55mm 60mm
3mm
3mm 3mm 3mm

Ø4.7mm
Ø4.7mm Ø4.7mm Ø 4.7mm

19mm
10 mm 13mm 16mm

PLASTERSTOP BEAD

Ref: PS10/3.0/SS PS13/3.0/SS PS16/3.0/SS PS19/3.0/SS

Lengths: 3.0m 3.0m 3.0m 3.0m

Packing: 50 lengths/pack 50 lengths/pack 50 lengths/pack 50 lengths/pack

Plasterstop Bead

24 Catnic International
Catnic Stainless Steel Beads
Architrave Beads

Application
Architrave beads give a shadow line decorative effect for aesthetic purposes and creates
a clean division between varying wall finishes eg. at wall and ceiling abutments or door and
window reveals.

Fixing
Fix either by nailing or using plaster dabs.

Quality
Manufactured from Stainless Steel to BSEN 10088 –2-1.4301.
All beads shown are manufactured in accordance with BS 6452: Part 1: 1984.

13mm 20mm 20mm 20mm

10mm 13mm 13mm 10mm 13mm
13mm

37mm 37mm 37mm 37mm

37mm

ARCHITRAVE

Ref: ARC10/WF/3.0/SS ARC13/WF/3.0/SS ARC20/WF/3.0/SS ARC10/WO/3.0/SS ARC13/WO/3.0/SS

Lengths: 3.0m 3.0M 3.0M 3.0M 3.0M

Packing: 25 lengths/pack 25 lengths/pack 30 lengths/pack 25 lengths/pack 25 lengths/pack

Architrave Bead

Catnic International 25
Catnic Stainless Steel Beads
Movement and Renderstop Beads

Application
Movement bead allows for movement between adjoining surface finishes resulting from
differential expansion or settlement. Allowable movement +/- 3mm.

Renderstop beads are used to obtain a neat, bell cast lower edge to external finishes and
helps to protect masonry against run-off water.

Fixing
Fix either by nailing or using plaster dabs.

Quality
Manufactured from Stainless Steel to BSEN 10088-2-1.4301.
All beads shown are manufactured in accordance with BS 6452: Part 1: 1984.

19mm

12mm
(15mm, 18mm, 21mm)

7mm
45mm

25mm 60°

25mm

MOVEMENT BEAD RENDERSTOP BEAD

Ref: MB10SS, MB13SS, RS3.0 SS

MB16SS, MB19SS

Lengths: 3.0m 3.0m

Packing: 10 lengths/pack 50 lenghts/pack

Movement Bead Renderstop Bead

26 Catnic International
Catnic Galvanised Beads with PVC Nose
Angle Beads

7mm 8mm 8.5mm

7mm 10mm 14mm

30mm 41mm 41mm

SQUARE HOLE ANGLE BEADS

Ref: 6000 6001 6050

Lengths: 2.5m, 3.0m 2.5m, 3.0m 2.5m, 3.0m

Packing: Shrink film Euro packaged Shrink film Euro packaged Shrink film Euro packaged
15 lengths/pack 15 lengths/pack 15 lengths/pack

8.5mm

15mm
14mm

8mm

52mm

53mm

SQUARE HOLE ANGLE BEADS

Ref: 6051 STD/PVC

Lengths: 2.5m, 3.0m 2.7m, 3.0m

Packing: Shrink film Euro packaged Shrink film Euro packaged
15 lengths/pack 50 lengths/pack

Square Hole Angle Bead with PVC Nose

Catnic International 27
Catnic Galvanised Beads with PVC Edge

53mm 53mm

53mm

galvanised
galvanised - blue galvanised - blue

aluminium - lighter grey aluminium - lighter grey

aluminium -

20mm 14mm- blue green

stainless steel stainless steel - blue green stainless ste
10mm
PVC - white PVC - white PVC - white

plaster dark plaster dark

plaster dark

plaster light
plaster light plaster light

PLASTERSTOP BEAD

Ref: 6222 6223 6224

Lengths: 2.7m, 3.0m 2.7m, 3.0m 2.7m 3.0m

Packing: Shrink packed Euro packaged Shrink packed Euro packaged Shrink packed Euro packaged
25 lengths/pack 25 lengths/pack 25 lengths/pack

galvanised - blue galvanised - blue galvanised -

aluminium - lighter grey aluminium - lighter grey aluminium - l

110º 110º 110º

stainless steel - blue green stainless steel - blue green stainless stee

53mm 53mm
PVC - white 53mm PVC - white PVC - white

plaster dark plaster dark plaster dark

plaster light plaster light plaster light

14mm 10mm 20mm

PLASTERSTOP BEAD

Ref: 6225 6227 6229

Lengths: 2.7m, 3.0m 2.7m, 3.0m 2.7m 3.0m

Packing: Shrink packed Euro packaged Shrink packed Euro packaged Shrink packed Euro packaged
25 lengths/pack 25 lengths/pack 25 lengths/pack

28 Catnic International
Catnic PVC Beads
Application
PVC-U beads are particularly useful in high humility areas avoiding the possibility of corrosion. They are suitable for both internal and
external use.

Fixing 5mm
3mm
13mm
For thin-coat plaster, beads can be fixed 3mm

with staples or joint filler and for thick coat 42mm

plaster applications, with either plaster 25mm

dabs or nails. Ø4mm

Quality Ø3mm

Beads are manufactured from high density

white PVC-U external window grade.
ANGLE BEAD CORNER BEAD

Ref: NR1535 NR1456

Steel finish: PVC-U PVC-U

Lengths: 2.4m, 3.0m 2.4m

Packing: 25 lengths/pack 25 lengths/pack

19mm

25mm
Ø 3mm

Ø4mm 3mm

7mm

50mm
plaster depth = 3mm

13mm

60°
25mm

25mm 25mm

PLASTERSTOP BEAD ANGLE BEAD CORNER BEAD

Ref: NR1536 NR1925 NR1660

Steel finish: PVC-U PVC-U PVC-U

Lengths: 2.4m 3.0m 3.0m

Packing: 25 lengths/pack 25 lengths/pack 25 lengths/pack

PVC-U Bell Cast Render Bead PVC-U Corner Bead PVC-U Drywall Corner Arch

Catnic International 29
Catnic Expanded Metal Lath
Diamond Lath
Expanded metal lath is extensively used as a background to plaster in order to
reinforce against cracks and it is especially useful at joints of dissimilar materials.
Generally DL111 or DL089 lath is used for wall situations and DL161 is used for
ceiling work.

Quality Assurance
Diamond Lath
Catnic expanded metal lath is manufactured in accordance with BS1369: Part 1:
1987. The galvanised steel used in the manufacture of metal lath is in accordance
with BSEN 10327: 2004 – DX51D+Z275. Where stainless steel is used it is in
accordance with BSEN 10088-2-1.4301.

Coil Lath

SHEET LATH CORNER LATH

Ref: S W Mesh Weight Material Sheet size Ref: Weight Width Material Lengths

DL089 9mm 0.9kg/m 2

Galvanised Steel 250 x 70cm LC023/50/2.5 1.61kg/m 2
5 x 5cm Galvanised Steel 250cm

DL111 9mm 1.11kg/m 2

Galvanised Steel 250 x 70cm LC023/75/2.5 1.61kg/m 2
7.5 x 7.5cm Galvanised Steel 250cm

DL161 9mm 1.61kg/m2 Galvanised Steel 250 x 70cm

DL111S 9mm 1.11kg/m2 Stainless Steel 250 x 70cm

STRIP LATH COIL LATH

Ref: Weight Width Material Lengths Ref: Weight Width Material Lengths

SL021/100/2.5 1.11kg/m2 10cm Galvanised Steel 250cm CL021/100/100 1.11kg/m2 10cm Galvanised Steel 100 metres

SL021/150/2.5 1.11kg/m 2
15cm Galvanised Steel 250cm CL021/150/100 1.11kg/m 2
15cm Galvanised Steel 100 metres

SL023/100/2.5 1.61kg/m2 10cm Galvanised Steel 250cm CL021/200/100 1.11kg/m2 20cm Galvanised Steel 100 metres

SL023/150/2.5 1.61kg/m 2
15cm Galvanised Steel 250cm CL023/100/100 1.61kg/m 2
10cm Galvanised Steel 100 metres

CL023/150/100 1.61kg/m2 15cm Galvanised Steel 100 metres

CL023/200/100 1.61kg/m 2
20cm Galvanised Steel 100 metres

Sheet Lath Corner Lath Strip Lath

30 Catnic International
Catnic Expanded Metal Lath
Rib Lath
Rib lath is extensively used as a plaster background for ceilings, walls and
partitions. Generally 148 is suitable for wall situations. For ceiling work 184/222
should be used.

Quality Assurance
Catnic expanded rib lath is manufactured in accordance with BS1369: Part 1: 1987.
The galvanised steel used in the manufacture of rib lath is in accordance with BSEN
10327:2004-DX51D+Z275. Where stainless steel is used it is in accordance with
BSEN 10088-2-1.4301.

RIB LATH
Ref: Weight Material Size Rib Height

RIB148 1.48kg/m 2
Galvanised Steel 250 x 70cm 10mm

RIB184 1.84kg/m 2
Galvanised Steel 250 x 70cm 10mm

RIB222 2.22kg/m2 Galvanised Steel 250 x 70cm 10mm

RIB148S 1.48kg/m 2
Stainless Steel 250 x 70cm 10mm

RIB184S 1.84kg/m2 Stainless Steel 250 x 70cm 10mm

Refurbishment of Masonry
Stainless steel rib lath is ideal for refurbishing damaged or aged masonry walls,
when a key for rendering is not certain due to disintegration or softening of the wall
face.

Lath should be fixed with apexes of ribs against the wall, edge ribs of the sheets
nesting into each other should be wire-tied every 15cm and ends of sheets should
be lapped not less than 2.5cm and nesting ribs securely tied together.

Stainless steel fixings should be used at sufficient intervals to hold the lath firmly in
position.

Rib Lath

Catnic International 31
Catnic Mesh Arch Formers – Galvanised
Mesh Arch Formers
The Catnic arch former is the easy way to create attractive and perfectly finished
arches. For walls of up to 160mm thick, the frame sections are designed to be
overlapped. For walls 160-300mm thick, standard infill soffit pieces are provided to
bridge the gap between the sections. If the thickness of the wall is between 300-
565mm, an Extra Soffit piece is available.

Each arch is supplied with installation instructions and a complete fixing kit. Soffit
pieces are also included for walls up to 300mm thick.

Quality Assurance
The galvanised steel used in the manufacture of mesh arch formers is in accordance
with BSEN 10327:2004-DX51D+Z275.

Note: Catnic arches are non-loadbearing, decorative features and will therefore not support walls. If there is
any doubt about suitability, please contact us.

Milano Extra Soffit Section

60mm

rise
295 x 1200mm

Brick to brick
60mm
dimension

Verona Verona with bridging sections

610mm
60mm

80mm

60mm
rise

Brick to brick
dimension
60mm

32 Catnic International
Catnic Mesh Arch Formers
Brick to brick VERONA MILANO
dimension (mm) Ref no. Rise (mm) Ref no. Rise (mm)

750 VE 0750 375

800 VE 0800 400

850 VE 0850 425

900 VE 0900 450

1000 VE 1000 500

1200 VE 1200 600 MI 1200 280

1500 VE 1500 750 MI 1500 330

1800 MI 1800 375

2400 MI 2400 375

Note: These products are excluded from our BSEN ISO 9001:2000 registration as they are not manufactured
on Catnic premises.

Bridging Section
Ref Length

BS 061 610mm

Extra Soffit Section

Ref Size Wall thickness

ES 0295 295 x 1200mm 300 – 565mm

Installation

1 2 3 4
> Measure the distance between the walls (brick to brick) and select the appropriate arch size. If renovating,
remove existing plaster down to the masonry. Mark the centre of the aperture.
> Position the first section of the arch to the wall and fix with the masonry nails provided.
> Fix the other sections in the same way, aligning them at the centre with the plastic joining pieces provided.
All arches and soffit pieces should be joined with the self tapping screws provided.
> The arch is completed by plastering directly onto the steel mesh, using a suitable material.

Catnic International 33
Catnic Coil Mesh for Blockwork
Galvanised & Stainless Steel

Coil Mesh
Anti-crack reinforcement for non-structural use.

Quality Assurance
Manufactured from either galvanised steel to BSEN 10327:2004-DX51D+Z275,
or stainless steel to BSEN 10088-2-1.4301.

Coil mesh
Ref: Wall width Coil width Coil length
mm mm metres

CM 50 100 50 50 or 20

CM 64 114 64 50 or 20

CM 100 150 100 100 or 20

CM 114 164 114 100 or 20

CM 150 200 150 100 or 20

CM 178 228 178 100 or 20

CM 200 250 200 100 or 20

CM 229 279 229 100 or 20

CM 305 355 305 100 or 20

Catnic Coil Mesh for Non Structural Usage

Expanded metal type bed joint reinforcement is supplied as an anti-crack
reinforcement in the design and construction of brick and block masonry.

Guidance for its use is given in BS 5628 : Part 3 : 2001 cl.5.4.5

It is generally provided at areas of high stress concentration to dissipate these

stresses to areas of low stress. A typical example would be at a point where the
section of wall changes, such as at a door or window opening. The cracking
of masonry due to changes in temperature, changes in moisture content and
settlement of foundations can all be controlled by the use of block reinforcement.

Coil mesh

34 Catnic International
Catnic Wall Accessories

Wall Connectors
Catnic’s Wall Connectors are a simple yet effective
system for tying new masonry walls to existing walls.

Wall Ties
All Catnic wall ties are manufactured from high quality
stainless steel wire and strip materials to ensure
that structural design properties are maintained
throughout the life of the structure.
Brick and Block Spacer System
The revolutionary new way to lay perfect brickwork
and blockwork.

Catnic International 35
Wall Ties – Stainless Steel
Wall Ties
Catnic Wall Ties are manufactured from stainless steel in accordance with
BSEN 10088-2-1.4301 (strip), BSEN 10088-3:2005 min. 18/8 composition (wire).

Ref Length Width Cavity width Packing

BB-3 220mm 19mm 75mm Cartons of 250

For fixing masonry to masonry in cavity walls of domestic houses and small commercial buildings of up to
five storeys but not exceeding 15m in height. Tie density 2.4 ties/m2. Based on a design windspeed up to
56m/s.

Ref Length Width Cavity width Packing

BB-2 191mm 19mm 50mm Cartons of 250

For fixing masonry to masonry in cavity walls of domestic houses and small commercial buildings of up
to three storeys but not exceeding 15m in height. Tie density 2.4 ties/m2. Based on a design windspeed
up to 56m/s.

Ref Length Width Cavity width Packing

BT 2-4 120mm 19mm 50mm Cartons of 250

For fixing masonry to timber framing in single and two storey dwellings up to a maximum height of 8m.
Also suitable for block to concrete applications. Tie density and windspeed refer to BBA certificate.

BB-2 DD140 Part 2 Catnic BB-2

1987 type 2 requirement

Tensile Load (N) At serviceability 500 1321

Tensile Load (N) At failure 1800 3183

Comprehensive Load (N) At serviceability 400 552

Comprehensive Load (N) At failure 1300 1300

BB-3 DD140 Part 2 Catnic BB-3

1987 type 2 requirement

Tensile Load (N) At serviceability 500 1529

Tensile Load (N) At failure 1800 4051

Comprehensive Load (N) At serviceability 400 1540

Comprehensive Load (N) At failure 1300 2374

Stainless Steel Strip Ties

Cavity Design Tie Size (mm) Specify DD140: Part 2 Wind Speed

50mm 3 storeys up to 15m 0.6 x 19 x 191 BB-2 Type 2 Up to 56m/s

50mm 5 storeys up to 15m 0.8 x 19 x 220 BB-3 Type 2 Up to 56m/s

50mm 4 storeys up to 12m 0.6 x 19 x 120 BT2-4 Up to 50m/s

BB-3 BB-2 BT 2-4

36 Catnic International
Wall Connectors
Galvanised & Stainless Steel
Wall Connectors
Catnic wall connectors are suitable for wall thicknesses from 60mm up to 250mm
and one pack contains all of the required fixings for a single wall of 2.4m high. This
product is available with a choice of two different materials.

STRONGHOLD WALL CONNECTORS

Ref: SWC

Material Stainless Steel to BSEN 10088-2-1.4301

Packaging 20 packs per carton

GALVANISED WALL CONNECTORS

Ref: GWC

Material Galvanised Steel to BSEN 10327: 2004-DX51D+Z275

Packaging 20 packs per carton

Stronghold Wall Connector Galvanised Wall Connector

Catnic International 37
Build more
with Brikmat
Brikmat is the revolutionary new range of masonry support
and bed joint reinforcement systems designed to make
blockwork a breeze...

Brikmat Brikmat Reinforcement

Brikmat is a masonry support system that eliminates Brikmat bed-joint reinforcement system increases the
bed joint compression providing a stable platform for compressive strength and rigidity of the heavy blockwork,
additional courses of physically demanding masonry to providing a stable platform for additional courses of
be built. physically demanding masonry to be built.

Guaranteed consistent mortar joint. Reinforces and supports heavy blockwork.

Easy to use, no training required. Increases the flexural strength of stack-bonded masonry.

Increases speed and improves productivity. Relieves stress concentration around openings.

Improves accuracy and ensures aesthetic finish. Allows cladding panels to be increased in size.

38 Catnic International
 Ibstock, Fireborn Red

Why use Brikmat?

Specifiers Main Contractor Bricklayer / Builder

Specify with confidence Saves time & money Greater speed

Specify dense architectural masonry More successive courses in a single lift Proven to be up to 3 times faster than
products with confidence. equates to improved productivity and conventional building methods.
less time on site.
Guarantee the aesthetic finish Improved productivity
of your design. Improve block laying speed up to three Build up to 10 courses* of dense
times faster. aggregate block work in a single lift
Save time and money for your client.
without compression of the mortar
Hidden savings
Eliminate time spent dealing with bed-joints at lower levels.
Scaffolding down sooner.
block panel issues on site.
Use a standard mortar mix. No waiting
Bricklayers off site sooner.
for mortar to harden before continuing
Following trades can be on site sooner. to build.

Mortar silos collected and off site sooner. Enhanced accuracy

A quality finish virtually guaranteed.
Wastage reduction
Saving of up to 60% on mortar wastage. Consistent gauge height, even after
10 courses.
No “bulking up” of joints required.
Prevents extrusion of the mortar due
Minimal bleeding of mortar onto block
to pressure from successive courses
face.
= no mortar bleeding on fair-faced
Improve accuracy blockwork = no cleaning!
Helps consistency when teams of
bricklayers are working on projects.

Health & safety

Improved stability of block panels.

Less mortar on scaffolding boards.

Less mortar dropped below.

No need for chemical cleaning

of stained blockwork.

Catnic International 39
Brikmat fast build, perfect results.

Working with Brikmat Working with Brikmat Independently tested

Placed in the horizontal bed joints Reinforcement Independent testing conducted by CERAM
to increase the stability of physically In addition to the features of Brikmat, Research Limited clearly demonstrated
demanding masonry, Brikmat resists Brikmat Reinforcement also: the tangible benefits of using Brikmat with
the stresses that are inherent in loaded physically demanding masonry.
Increases the flexural strength with
masonry panels eliminating the risk
stack-bonded masonry. The CERAM report also highlighted:
of bed joint compression and mortar
bleeding. Increases the recommended distance Walls being built without Brikmat can
between movement joints. be as much as 6mm-10mm out of
Suitable for stretch bonded masonry.
plumb on the 5th course.
Strengthens areas of concentrated
Eliminates bed joint compression.
loads and assist in resisting effects of Walls built with Brikmat use up to 60%
Reduces mortar bleeding. stresses caused by earth movements less mortar.
reducing the likelihood of cracking in
Provides increased stability. Bed joints in walls built with Brikmat
the brickwork.
do not alter in thickness through a
Continue building without waiting
Allows cladding panels to be increased 10-course construction.
for mortar to cure.
in size.
Walls built with Brikmat can be built up
Relieves stress concentration around to 3 times faster than those without the
openings such as windows and doors. support of Brikmat.

Brikmat product properties

Product code Length(mm) Width(mm) Gauge Colour Pack Linear metres
height (mm) quantity per box(m)

BM9 870 80 9.0 Blue 25 21.75

BM11 870 80 10.7 White 25 21.75

Brikmat Reinforcement product properties

Product code Diameter Width Length Minimum Characteristic Pack
(mm) (mm) (mm) X sec area tensile strength quantity
(mm2) (n/mm2)

BMR3.0/60 3.0 60 3000 7.07 800 30

BMR3.5/60 3.5 60 3000 9.62 800 30

BMR4.0/60 4.0 60 3000 12.56 800 30

BMR3.0/100 3.0 100 3000 7.07 800 30

BMR3.5/100 3.5 100 3000 9.62 800 30

BMR4.0/100 4.0 100 3000 12.56 800 30

BMR3.0/150 3.0 150 3000 7.07 800 30

BMR3.5/150 3.5 150 3000 9.62 800 30

BMR4.0/150 4.0 150 3000 12.56 800 30

A full copy of the CERAM test report

is available on request.

40 Catnic International
Fencepost Supports

Catnic International 41
Fencepost Supports
QwikPost Fencepost Supports
QwikPost is a durable and affordable fence post fixing system. The range includes:

QWIKPOST SPIKE

Ref SPK5045 SPK7560 SPK7570 SPK1070

Size (mm) 50 x 50 x 450 75 x 75 x 600 75 x 75 x 700 100 x 100 x 700

Packaging 10 per carton 10 per carton 10 per carton 10 per carton

QWIKPOST REPAIR SPIKE QWIKPOST CONCRETE-IN SUPPORT

Ref REP75 CON75 CON100

Size (mm) 75 x 75 75 x 75 100 x 100

Packaging 10 per carton 10 per carton 10 per carton

QWIKPOST COLT-DOWN SUPPORT QWIKPOST STANDARD ARRIS BRACKET

Ref BLT50 BLT75 ARB001

Size (mm) 50 x 50 75 x 75

Packaging 10 per carton 10 per carton 100 per carton

QWIKPOST U-CLIPS QWIKPOST Z-CLIPS

Ref UCP47 UCP52 ZED001

Size (mm) Small 47mm Large 52mm

Packaging 250 per carton 250 per carton 200 per carton

QwikPost Spike

QWIKPOST UNIVERSAL POST EXTENDER QWIKPOST DRIVE-IN TOOL

Ref UPE DOL

Size (mm)
Packaging 10 per carton 10 per carton

QwikPost Repair Spike QwikPost Concrete-in QwikPost Bolt-down QwikPost Standard QwikPost U-Clips QwikPost Z-Clips QwikPost Universal QwikPost Drive-in Tool
Support Support Arris bracket Post Extender

42 Catnic International
Catnic

Technical Specification Clauses

All backgrounds should be free of deleterious substances such as mould, oil and grease and be adequately prepared to accommodate
the finished surface, all beading and attendant fixings at the specified depths.

Catnic beads should be fixed at a nominal 600mm spacing by embedding with dabs of the same material used for the undercoat or
corrosion resistant galvanised nails for galvanised bead and stainless steel nails for stainless steel bead.

1. Angle bead or corner bead Stainless Architrave beads shall be 6. Expanded metal lath
Galvanised Angle bead shall be manufactured in accordance with BS 6452: Galvanised Expanded metal lath shall
manufactured in accordance with BS 6452: Part1: 1984 using stainless steel to BSEN be manufactured in accordance with BS
Part1: 1984 using galvanised steel to BS 10088-2-1.4301 and to suit plaster thickness 1369: Part1: 1987 using galvanised steel to
EN 10327-DX51D+Z275 with 45mm (53mm: of 10mm (13mm) without (with) return BSEN 10327-DX51D+Z275 and weighing
65mm) wing size as manufactured by flange as manufactured by Catnic under 0.90kgs per sq.metre (1.11kgs per sq.metre:
Catnic under code reference SS3.0 (STD3.0: code reference ARC10/WF/3.0/SS (ARC10/ 1.61kgs per sq.metre) as manufactured by
WW3.0). WF/3.0/SS, ARC13/W0/3.0/SS, ARC13/ Catnic under code reference DL080 (DL111:
WF/3.0/SS, ARC20/WF/3.0/SS. DL161).
Stainless Angle bead shall be manufactured
in accordance with BS 6452: Part1: Stainless Expanded metal lath shall be
1984 using stainless steel to BSEN 4. Movement bead manufactured in accordance with BS 1369:
10088-2-1.4301 with 53mm wing size Galvanised Movement beads shall be Part1: 1987 using stainless steel to BSEN
as manufactured by Catnic under code manufactured in accordance with BS 6452: 10088-2-1.4301 and weighing 1.11kgs per
reference STD3.0SS. Part1: 1984 using galvanised steel to BSEN sq.metre as manufactured by Catnic under
10327-DX51D+Z275 and to suit plaster code reference DL111/SS.
2. Plasterstop or casing bead thickness of 12mm (15mm: 18mm: 21mm)
Galvanised Plasterstops shall be as manufactured by Catnic under code 7. Rib Lath
manufactured in accordance with BS 6452: reference MB10/3.0 (MB13/3.0: MB16/3.0: Galvanised Rib Lath shall be manufactured
Part1: 1984 using galvanised steel to BSEN MB19/3.0). in accordance with BS 1369: Part1: 1987
10327-DX51D+Z275 and to suit plaster Stainless Movement beads shall be using galvanised steel to BSEN 10327-
thickness of 10mm (13mm: 16mm: 19mm) manufactured in accordance with BS DX51D+Z275 with 10mm ribs at 100mm
as manufactured by Catnic under code 6452: Part1: 1984 using stainless steel to centres and weighing 1.48kgs per sq.metre
reference PS10/3.0 (PS13/3.0: PS16/3.0: BSEN 10088-2-1.4301 and to suit plaster (1.84kgs per sq.metre: 2.22 per sq.metre)
PS19/3.0). thickness of 12mm (15mm: 18mm: 21mm) as manufactured by Catnic under code
Stainless Plasterstops shall be as manufactured by Catnic under code reference RIB148 (RIB184: RIB222).
manufactured in accordance with BS reference MB10/3.0/SS (MB13/3.0/SS: Stainless Rib Lath shall be manufactured in
6452: Part1: 1984 using stainless steel to MB16/3.0/SS: MB19/3.0/SS). accordance with BS 1369: Part1: 1987 using
BSEN 10088-2-1.4301 and to suit plaster stainless steel to BSEN 10088-2-1.4301 with
thickness of 10mm (13mm: 16mm: 19mm) 5. Renderstop 10mm ribs at 100mm centres and weighing
as manufactured by Catnic under code Galvanised Renderstops shall be 1.48kgs per sq.metre (1.84kgs per sq.metre)
reference PS10/3.0/SS (PS13/3.0/SS: manufactured in accordance with BS 6452: as manufactured by Catnic under code
PS16/3.0/SS: PS19/3.0/SS). Part1: 1984 using galvanised steel to BSEN reference RIB148/SS (RIB184/SS).
10327-DX51D+Z275 as manufactured by
3. Architrave beads Catnic under code reference RS3.0. 8. Steel lintels
Galvanised Architrave beads shall be Stainless Renderstops shall be Steel lintels shall be manufactured
manufactured in accordance with BS manufactured in accordance with BS 6452: in accordance with BS 5977: Part2:
6452: Part1: 1984 using galvanised steel Part1: 1984 using stainless steel to BSEN 1983 using galvanised steel to BSEN
to BS EN 10327-DX51D +Z275 and to suit 10088-2-1.4301 as manufactured by Catnic 10327-DX51D+Z275 and coated with a
plaster thickness of 10mm (13mm) without under code reference RS/3.0/SS. thermosetting polyester powder coating as
(with) return flange as manufactured by manufactured by Catnic.
Catnic under code reference ARC10/
WF/3.0 (ARC13/WF/3.0: ARC20/WF/3.0) or
ARC10WO/3.0 (ARC13/WO/3.0).

Catnic International 43
www.catnic.com

Catnic is a Corus Group company.

Further Information can be found on the
Corus website at www.corusgroup.com

Copyright Corus UK Limited 2007

Design: ELEVATOR www.elevatordesign.co.uk

Catnic
International Sales Department
Corus UK Limited
Pontypandy Estate
Caerphilly
CF83 3GL
Telephone +44 (0) 29 2033 7900
Facsimile +44 (0) 29 2088 0855