Scribd
Upload
275 views14 pages

Qlite Presentation FTC

This presentation summarizes the Qlite Lighting Control System that will be used for the Security Training Facilities project in Dammam, Saudi Arabia. The system uses various components like switching modules, controller modules, power supplies, push button control plates, photocell sensors, and dry contact interfaces to automate lighting control based on occupancy, daylight, or time schedules. It can integrate with building management systems through a dry contact interface module to provide lighting control and automation.

Uploaded by

Arman Ul Nasar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
275 views14 pages

Qlite Presentation FTC

This presentation summarizes the Qlite Lighting Control System that will be used for the Security Training Facilities project in Dammam, Saudi Arabia. The system uses various components like switching modules, controller modules, power supplies, push button control plates, photocell sensors, and dry contact interfaces to automate lighting control based on occupancy, daylight, or time schedules. It can integrate with building management systems through a dry contact interface module to provide lighting control and automation.

Uploaded by

Arman Ul Nasar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 14

Presentation On: Qlite Lighting Control System

Project: Security Training Facilities Dammam


Client: Ministry of Interior, KSA
Controctor: Al-Khodari
Electrical Sub. Contractor: M.E.C.
Dated: 9 Sep. 2013

Presentation Topics
1

Qlite Lighting Control


System

System Architecture

List of Components Used

BMS Control

Qlite Lighting Control System


Lighting control systems are used mainly for efficient and
intelligent energy management. This system enables the
switching (ON & OFF) of the light fittings via a stand-alone
system or a fully networked central system. They can be used in
public, commercial or residential properties for areas such as
corridors, restrooms, BOH areas, administrative offices, car park,
and staircase usually as stand-alone systems or in combination
with dimming control system.

The system enables the control of light fittings through timers


and/or any pre-programmed logic function as specified or needed
by the client.

System Architecture

System Architecture

Automated Controls of lights based on Occupancy, daylight or


time Schedule
Integration with BMS
Local Preset control from a Key Pad

List of Components Use in


STF
Project
Switching Module

Features
QL-SW810

Standard DMX-512 signal.


Din rail-mounted. Manual setting
available and easy to operate.
8 channels dry contact, each can be
set as ON/OFF/ AUTO mode individually.
Each channels maximal output can be
10A.
Up to 99 zones synchronization. (99
devices work together)
Specification:
Delay time setting (0.1S~10S) for
Power Supply: AC 90240V
Output: Maximal output of each channel each channel to avoid current surge.
is 10A
Connectable to QL series control
Protocol: DMX-512/QL-Net
Dimension:215 (W) x 59(H) x 87.5(D)mmpanels, each of
Weight: 800g
them can work independently or
synchronously.

List of Components Use in


STF
Project
Controller Module
QL-NE100

Specification:
Power Supply: 90 - 240V AC
Protocol: DMX-512, QL-Net
Output: 5A per channel, total 12A.
Dimension: 215mm(W) x 88mm(H) x
57mm(D)
Weight: 720g

Features

DMX-512/QL-NET(RS-485)
Din-rail mounted.
8 channels leading-edge (forward
phase control) output.
Each channel can be set as
dimming/switch mode.
Up to 99 zones setting.
Connectable to QLCP series control
panel.

List of Components Use in


STF
Project
Power Supply Module
QL-PS1202

Specification:
AC Input: 90 240V
DC Output: 12V, 2A Max
Dimension: 90(W) x 88 (H) x 57 (D) mm
Weight: 310g

List of Components Use in


STF
Push Button Control
PlateProject

Features

In multi-zone mode, one QL-CP106


can control 8 zones.
In single zone mode, one QL-CP106
can set up to 255 zones by the DIP
switch.
Press [1.....6] number key buttons from
control panel to directly recall 6 scenes.
Press or to raise and lower the
dimming level.
Specification:
In curtain control mode,[5&6] number
IR receiver.
Protocol : QL-NET (RS-485)
key button can be used for open and
Connector : 4 pin green terminal
Dimension : 86(W) X 86(H) X 34.6(D)mm close control of the curtains/blinds.
Weight : 100 g
256 level dimming resolutions.
Key Lock /unlock function.

QL-CP106

List of Components Use in


Photocell Sensor STF Project

Photocell sensor module sits on the QL NET bus and takes


power from the bus.

List of Components Use in


STF
Project
QL-S8

Specification:
Power supply: DC-12V 200mA (supply
by QL-net 4pin green terminal)
Protocol:RS-485
Signal input connector :4 PIN green
terminal /PHONE JACK
Signal output connector:18PIN green
terminal
Signal output channel8 channels
Dimension100(W)*76(H)*35 (D)mm
Weight220g

Features

8 channels. Can connect to 8 dry


contacts.
Each dry contact has two modes:
scene or channel mode.
Can set dry contacts working period.
(The dry contact works only within this
period.)
Can set dry contacts delay time. In
scene mode, after a scene was call out it
will automatically call out another scene
or the OFF scene after delay time; in
channel mode, after a channel was
switch on, it will automatically switch on
another channel or switch the channel
off after delay time.

List of Components Use in


STF
Project
Lighting Control & Automation Panels

BMS Control

In each Building eight Zones(areas) for BMS Control will be


programmed in Qlite Lighting Control System.

QL-S8 will provide the interface between Qlite Lighting Cont


System and BMS.

THANK YOU

You might also like