====== Linksys EA7300 v1====== {{page>meta:infobox:construction&noheader&nofooter&noeditbtn}} ===== Linksys Max-Stream AC1750 MU-MIMO Gigabit Router ===== Gigabit Ethernet switch based device, 1 x USB 3.0 port, 2.4GHz and 5GHz WiFi-5 support. This router has four antennas, 3 external with 1 internal. The three external antennas are fixed and cannot be removed. Dual-firmware support allows you to easily switch back to the stock firmware. /*****/ /* How to add images ========> http://openwrt.org/meta/adding_images_to_openwrt_wiki */ /*****/ {{media:ea7300v1.png?200|Linksys EA7300v1}} ===== Supported Versions ===== ===== Hardware Highlights ===== ===== Installation ===== ==== Flash Layout ==== See also [[docs:techref:flash.layout|Flash layout]] $ cat /proc/mtd dev: size erasesize name mtd0: 07f80000 00020000 "ALL" mtd1: 00080000 00020000 "boot" mtd2: 00040000 00020000 "u_env" mtd3: 00040000 00020000 "Factory" mtd4: 00040000 00020000 "s_env" mtd5: 00040000 00020000 "devinfo" mtd6: 02800000 00020000 "kernel" mtd7: 02400000 00020000 "rootfs" mtd8: 02800000 00020000 "alt_kernel" mtd9: 02400000 00020000 "alt_rootfs" mtd10: 00100000 00020000 "sysdiag" mtd11: 02d00000 00020000 "syscfg" ==== OEM easy installation ==== Flash ''...factory.bin'' image through GUI. This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWrt without problems. There are more detailed instructions for the v2 version of this device that also seem to work with the v1 version, [[:toh:linksys:ea7300_v2#installation]]. OEM firmware can be found here: https://downloads.linksys.com/support/assets/firmware/FW_EA7300_1.0.11.200282_prod.img /* ==== OEM installation using the TFTP method ==== -> [[docs:guide-user:installation:generic.flashing.tftp]] === Specific values needed for tftp === FIXME Enter values for "FILL-IN" below ^ Bootloader tftp server IPv4 address | FILL-IN | ^ Bootloader MAC address (special) | FILL-IN | ^ Firmware tftp image | [[:downloads|Latest OpenWrt release]] (**''NOTE:''** Name must contain //"tftp"//) | ^ TFTP transfer window | FILL-IN seconds | ^ TFTP window start | approximately FILL-IN seconds after power on | ^ TFTP client required IP address | FILL-IN | */ ===== Upgrading OpenWrt ===== -> [[docs:guide-user:installation:generic.sysupgrade]] FIXME These are generic instructions. Update with your router's specifics. ==== LuCI Web Upgrade Process ==== * Browse to ''http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/'' LuCI Upgrade URL * Upload image file for sysupgrade to LuCI * Wait for reboot ==== Terminal Upgrade Process ==== If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading: * ''sysupgrade'' * ''mtd'' Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. === sysupgrade === * Login as root via SSH on 192.168.1.1, then enter the following commands: cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc sysupgrade /tmp/xxx.abc === mtd === If ''sysupgrade'' does not support this router, use ''mtd''. * Login as root via SSH on 192.168.1.1, then enter the following commands: cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc mtd write /tmp/xxx.abc linux && reboot ===== Back to OEM/stock firmware ===== Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWrt from your router simply flash the OEM image at this point. You can also try to remove the DC power connector. Plug it back and the Linksys logo turns on. Then it turns off. Count 4 times "Logo turns on" and disconect the DC power connector. Repeat for about 3 times, and the bootloader switches the boot partition. ===== Debricking ===== -> [[docs:guide-user:troubleshooting:generic.debrick]] ===== Failsafe mode ===== -> [[docs:guide-user:troubleshooting:failsafe_and_factory_reset]] ===== Basic configuration ===== -> [[docs:guide-user:base-system:start|Basic configuration]] After flashing, proceed with this.\\ Set up your Internet connection, configure wireless, configure USB port, etc. ===== Specific Configuration ===== FIXME Please fill in real values for this device, then remove the EXAMPLEs ==== Network interfaces ==== The default network configuration is: ^ Interface Name ^ Description ^ Default configuration ^ | br-lan | EXAMPLE LAN & WiFi | EXAMPLE 192.168.1.1/24 | | vlan0 (eth0.0) | EXAMPLE LAN ports (1 to 4) | EXAMPLE None | | vlan1 (eth0.1) | EXAMPLE WAN port | EXAMPLE DHCP | | wl0 | EXAMPLE WiFi | EXAMPLE Disabled | ==== Switch Ports (for VLANs) ==== FIXME Please fill in real values for this device, then remove the EXAMPLEs Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on. ^ Port ^ Switch port ^ | Internet (WAN) | EXAMPLE 4 | | LAN 1 | EXAMPLE 3 | | LAN 2 | EXAMPLE 2 | | LAN 3 | EXAMPLE 1 | | LAN 4 | EXAMPLE 0 | ==== Buttons ==== -> [[docs:guide-user:hardware:hardware.button]] on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto. FIXME Please fill in real values for this device, then remove the EXAMPLEs The Linksys EA7300 has the following buttons: ^ BUTTON ^ Event ^ | EXAMPLE Reset | reset | | EXAMPLE Secure Easy Setup | ses | | EXAMPLE No buttons at all. | - | ===== Hardware ===== ==== Info ==== ==== Photos ==== /* =====>>>>> Standard size for photos: add ?400 to the medialink */ /* When uploading photos, **name them** intelligently. Nobody knows what 20100930_000602.jpg is! */ /* e.g. {{:media:yourbrand:yourbrand_yourmodel_front.jpg?400|}} */ /* Thanks, your wiki administration - Oct. 2015 */ //Front://\\ **Insert photo of front of the casing** //Back://\\ **Insert photo of back of the casing** //Backside label://\\ **Insert photo of backside label** ==== Opening the case ==== -> [[:docs:guide-user:warranty|Warranty]] Caution should be taken when opening in the case. The case is held together by four screws, hidden underneath the four rubber feet on the bottom of the unit. The rubber feet have an adhesive on them and peel off to reveal the screws. Once the four rubber feet and four screws have been removed, there are a number of small, plastic clips inside the case which break easily. Use plastic prying tools to detach the cover. //Main PCB://\\ {{:media:linksys:ea7300v2_pcb.jpg?direct&400|}} ==== Serial ==== -> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc. How to connect to the Serial Port of this specific device:\\ **Insert photo of PCB with markings for serial port** Pins are marked on PCB as follows: VCC RX TX GND ^ Serial connection parameters\\ for Linksys EA7300 v1 | 115200, 8N1 | ==== JTAG ==== -> [[docs:techref:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc. How to connect to the JTAG Port of this specific device:\\ **Insert photo of PCB with markings for JTAG port** ===== Bootloader mods ===== -> [[docs:techref:bootloader]] ===== Bootlogs ===== ==== OEM bootlog ==== =================================================================== MT7621 stage1 code 10:33:11 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0x2, 1/0 = 708/316 09000000 PLL4 FB_DL: 0xc, 1/0 = 616/408 31000000 PLL2 FB_DL: 0x10, 1/0 = 763/261 41000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 000F:| 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0010:| 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0011:| 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 16 rank 0 fine = 40 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_R0DELDLY[018]=00001E1F ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 11 1 11 1 9 0 9 0 0 7 10 | 0 9 4 7 0 7 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =31 DQS1 = 30 ================================================================== bit DQS0 bit DQS1 0 (1~59)30 8 (4~56)30 1 (2~54)28 9 (1~58)29 2 (2~61)31 10 (1~56)28 3 (1~52)26 11 (2~56)29 4 (1~58)29 12 (1~58)29 5 (2~56)29 13 (1~58)29 6 (1~59)30 14 (2~58)30 7 (2~60)31 15 (1~57)29 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 12 4 11 6 11 2 10 0 0 8 10 | 2 10 5 8 0 8 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff01aa DQ loop=14, cmp_err_1 = ffff00a8 dqs_perbyte_dly.last_dqdly_pass[1]=14, finish count=1 DQ loop=13, cmp_err_1 = ffff00a0 DQ loop=12, cmp_err_1 = ffff0080 DQ loop=11, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=11, finish count=2 byte:0, (DQS,DQ)=(a,8) byte:1, (DQS,DQ)=(8,8) 20,data:8a [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Aug 5 2016 - 15:06:22) SERCOMM v1.03.0, Release date: 2016/08/05 Board: Ralink APSoC DRAM: 256 MB relocate_code Pointer at: 8ffa8000 Config XHCI 40M PLL Allocate 16 byte aligned buffer: 8ffdf070 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02] Device found in MTK table, ID: c2f1, EXT_ID: 809502 Support this Device in MTK table! c2f1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 ..============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Aug 5 2016 Time:15:06:22 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 set LAN/WAN WLLLL Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 #### auto_recovery #### check env def auto_recovery no check env def auto_recovery yes check env def boot_part 1 check env def boot_part_ready 3 enabled:1, boot_part:2, boot_part_ready:3 ..nand read ret = 0x20000 boot_count:0, next_record:28 boot_count:0, next_record:28 3: System Boot system code via Flash. ## Booting image at be980000 ... Image Name: Linksys EA7300 Router Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2366689 Bytes = 2.3 MB Load Address: 80001000 Entry Point: 8000d1d0 ..................................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000d1d0) ... ## Giving linux memsize in MB, 256 Starting kernel ... LINUX started... THIS IS ASIC SDK 5.0.S.0 Initializing cgroup subsys cpu Linux version 2.6.36 (root@build-vm) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #81 SMP Mon Jun 12 00:10:59 PDT 2017 The CPU feqenuce set to 880 MHz GCMP present CPU revision is: 0001992f (MIPS 1004Kc) Software DMA cache coherency Determined physical RAM map: memory: 10000000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x0000c000 Normal 0x0000c000 -> 0x00010000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00010000 Detected 3 available secondary CPU(s) PERCPU: Embedded 7 pages/cpu @8c204000 s6912 r8192 d13568 u65536 pcpu-alloc: s6912 r8192 d13568 u65536 alloc=16*4096 pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock8 ro rootfstype=jffs2 init=/sbin/init PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Writing ErrCtl register=000021e6 Readback ErrCtl register=000021e6 allocated 1310720 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Memory: 251276k/262144k available (5029k kernel code, 10868k reserved, 1589k data, 228k init, 0k highmem) Hierarchical RCU implementation. Verbose stalled-CPUs detection is disabled. NR_IRQS:128 Trying to install interrupt handler for IRQ24 Trying to install interrupt handler for IRQ25 Trying to install interrupt handler for IRQ22 Trying to install interrupt handler for IRQ9 Trying to install interrupt handler for IRQ10 Trying to install interrupt handler for IRQ11 Trying to install interrupt handler for IRQ12 Trying to install interrupt handler for IRQ13 Trying to install interrupt handler for IRQ14 Trying to install interrupt handler for IRQ16 Trying to install interrupt handler for IRQ17 Trying to install interrupt handler for IRQ18 Trying to install interrupt handler for IRQ19 Trying to install interrupt handler for IRQ20 Trying to install interrupt handler for IRQ21 Trying to install interrupt handler for IRQ23 Trying to install interrupt handler for IRQ26 Trying to install interrupt handler for IRQ27 Trying to install interrupt handler for IRQ28 Trying to install interrupt handler for IRQ15 Trying to install interrupt handler for IRQ8 Trying to install interrupt handler for IRQ29 Trying to install interrupt handler for IRQ30 Trying to install interrupt handler for IRQ31 console [ttyS1] enabled Calibrating delay loop... 561.15 BogoMIPS (lpj=1122304) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 Initializing cgroup subsys memory launch: starting cpu1 launch: cpu1 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. launch: starting cpu2 launch: cpu2 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. launch: starting cpu3 launch: cpu3 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Brought up 4 CPUs Synchronize counters across 4 CPUs: done. devtmpfs: initialized NET: Registered protocol family 16 release PCIe RST: RALINK_RSTCTRL = 7000000 PCIE PHY initialize ***** Xtal 40MHz ***** start MT7621 PCIe register access RALINK_RSTCTRL = 7000000 RALINK_CLKCFG1 = 77ffeff8 *************** MT7621 PCIe RC mode ************* PCIE2 no card, disable it(RST&CLK) pcie_link status = 0x3 RALINK_RSTCTRL= 3000000 *** Configure Device number setting of Virtual PCI-PCI bridge *** RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2 PCIE0 enabled PCIE1 enabled interrupt enable status: 300000 Port 1 N_FTS = 1b105000 Port 0 N_FTS = 1b105000 config reg done init_rt2880pci done bio: create slab at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] pci 0000:00:00.0: BAR 1: set to [mem 0x60200000-0x6020ffff] (PCI address [0x60200000-0x6020ffff] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff] pci 0000:00:01.0: BAR 1: set to [mem 0x60210000-0x6021ffff] (PCI address [0x60210000-0x6021ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x600fffff 64bit] (PCI address [0x60000000-0x600fffff] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [io disabled] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] pci 0000:00:00.0: bridge window [mem pref disabled] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit] pci 0000:02:00.0: BAR 0: set to [mem 0x60100000-0x601fffff 64bit] (PCI address [0x60100000-0x601fffff] pci 0000:00:01.0: PCI bridge to [bus 02-02] pci 0000:00:01.0: bridge window [io disabled] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] pci 0000:00:01.0: bridge window [mem pref disabled] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) PCI: Enabling device 0000:00:01.0 (0004 -> 0006) BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60200000 res[1]->end = 6020ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 BAR0 at slot 1 = 0 bus=0x0, slot = 0x1 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60210000 res[1]->end = 6021ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0, irq=0x4 res[0]->start = 60000000 res[0]->end = 600fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x2, slot = 0x1, irq=0x18 res[0]->start = 60100000 res[0]->end = 601fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource Ralink Systick timer NET: Registered protocol family 2 Clockevents: could not switch to one-shot mode: Clockevents: could not switch to one-shot mode: Clockevents: could not switch to one-shot mode: MIPS is not functional. MIPS is not functional. MIPS is not functional. Could not switch to high resolution mode on CPU 1 Could not switch to high resolution mode on CPU 0 Could not switch to high resolution mode on CPU 3 Clockevents: could not switch to one-shot mode: MIPS is not functional. Could not switch to high resolution mode on CPU 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 128 (order: 0, 4096 bytes) UDP-Lite hash table entries: 128 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. 4 CPUs re-calibrate udelay(lpj = 1167360) Load Kernel WDG Timer Module squashfs: version 4.0 (2009/01/31) Phillip Lougher JFFS2 version 2.2 (NAND) (ZLIB) (LZO) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. fuse init (API version 7.15) msgmni has been set to 490 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) register power led blinking slow. register wps led off. Ralink gpio driver initialized Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A brd: module loaded loop: module loaded MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error Allocate 16 byte aligned buffer: 806e7070 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02, 00809502] Device not found, ID: c2f1 Not Support this Device! chip_mode=00000001 Support this Device in MTK table! c2f1 NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit) [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Scanning device for bad blocks Signature matched and data read! load_fact_bbt success 1023 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Creating 12 MTD partitions on "MT7621-NAND": 0x000000000000-0x000007f80000 : "ALL" 0x000000000000-0x000000080000 : "boot" 0x000000080000-0x0000000c0000 : "u_env" 0x0000000c0000-0x000000100000 : "Factory" 0x000000100000-0x000000140000 : "s_env" 0x000000140000-0x000000180000 : "devinfo" 0x000000180000-0x000002980000 : "kernel" 0x000000580000-0x000002980000 : "rootfs" 0x000002980000-0x000005180000 : "alt_kernel" 0x000002d80000-0x000005180000 : "alt_rootfs" 0x000005180000-0x000005280000 : "sysdiag" 0x000005280000-0x000007f80000 : "syscfg" [mtk_nand] probe successfully! rdm_major = 253 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288033 Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288034 PROC INIT OK! Customize GPIO mode.change I2C & JTAG to GPIO mode. org gpio_mode: 000a05a8 update gpio_mode: 000a05ac new gpio_mode: 000a05ac Check Eth LED. PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256). FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) xhc_mtk xhc_mtk: xHCI Host Controller xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1 xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhc_mtk xhc_mtk: xHCI Host Controller xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mt_msdc_init: !!!!! SDXC Module Initialize Fail !!!!! u32 classifier Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (3926 buckets, 15704 max) ctnetlink v0.93: registering with nfnetlink. nf_conntrack_rtsp v0.6.21 loading IPVS: Registered protocols () IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: ipvs loaded. IPv4 over IPv4 tunneling driver GRE over IPv4 demultiplexor driver gre: can't add protocol nf_nat_rtsp v0.6.21 loading ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux TCP cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Bridge firewalling registered Ebtables v2.0 registered L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller Registering the dns_resolver key type jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000000: 0x0527 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000004: 0x57de instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000008: 0x3e59 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000000c: 0x2400 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000010: 0x0080 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000014: 0x0080 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000018: 0x4ecf instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000001c: 0x0505 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000020: 0x694c instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000024: 0x7973 instead Further such events for this erase block will not be printed Old JFFS2 bitmask found at 0x0001e848 You cannot use older JFFS2 filesystems with newer kernels jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020000: 0x2915 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020004: 0x33ab instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020008: 0xff71 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0002000c: 0xa5fe instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020010: 0xf45a instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020014: 0xec35 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020018: 0x656c instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0002001c: 0x6236 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020020: 0x0090 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020024: 0xfff1 instead Further such events for this erase block will not be printed jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040000: 0x7b2e instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040004: 0xeab3 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040008: 0xaa90 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0004000c: 0x56d5 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040010: 0xa3d7 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040014: 0x88b8 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040018: 0x537b instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0004001c: 0xe347 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040020: 0xfa7b instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040024: 0x1038 instead Further such events for this erase block will not be printed jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00060000: 0x47e5 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00060004: 0x68ff instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00060008: 0x27cb instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0006000c: 0x65aa instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00060010: 0x511c instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00060014: 0xaf37 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00060018: 0x0936 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0006001c: 0x20c8 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00060020: 0x9c17 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00060024: 0x1df6 instead Further such events for this erase block will not be printed jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00080000: 0x64fe instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00080004: 0xddb8 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00080008: 0x7132 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0008000c: 0x81db instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00080010: 0x17de instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00080014: 0xd411 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00080018: 0x0b48 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0008001c: 0x16fc instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00080020: 0xb00c instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00080024: 0x955f instead Further such events for this erase block will not be printed jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000a0000: 0x8c7a instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000a0004: 0xcda0 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000a0008: 0x9035 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000a000c: 0x7e94 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000a0010: 0x2242 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000a0014: 0xf290 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000a0018: 0x1bf5 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000a001c: 0x85ad instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000a0020: 0x25d0 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000a0024: 0x48cb instead Further such events for this erase block will not be printed jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000c0000: 0xd244 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000c0004: 0x4355 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000c0008: 0x80e4 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000c000c: 0xe928 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000c0010: 0xe9f8 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000c0014: 0x50f4 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000c0018: 0xcd3b instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000c001c: 0x4063 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000c0020: 0x590b instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000c0024: 0xecb4 instead Further such events for this erase block will not be printed Old JFFS2 bitmask found at 0x000ce694 You cannot use older JFFS2 filesystems with newer kernels Old JFFS2 bitmask found at 0x000d78b0 You cannot use older JFFS2 filesystems with newer kernels jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000e0000: 0xf5ab instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000e0004: 0xeb86 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000e0008: 0x1f4a instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000e000c: 0x5528 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000e0010: 0x350d instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000e0014: 0x584b instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000e0018: 0xbab0 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000e001c: 0x5d90 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000e0020: 0x5ed4 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000e0024: 0xa7bc instead Further such events for this erase block will not be printed Old JFFS2 bitmask found at 0x000f55a8 You cannot use older JFFS2 filesystems with newer kernels jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100000: 0x6e1b instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100004: 0x5f49 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100008: 0xe121 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0010000c: 0xc8d7 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100010: 0x8ffe instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100014: 0x7f8f instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100018: 0x3b19 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0010001c: 0xcf34 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100020: 0x3eeb instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100024: 0x43ce instead Further such events for this erase block will not be printed Old JFFS2 bitmask found at 0x00110a10 You cannot use older JFFS2 filesystems with newer kernels jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00120000: 0xc814 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00120004: 0xb8c3 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00120008: 0xfd47 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0012000c: 0x51a9 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00120010: 0xad68 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00120014: 0x475e instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00120018: 0x773f instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0012001c: 0x0c8a instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00120020: 0xa2c8 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00120024: 0xc121 instead Further such events for this erase block will not be printed jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00140000: 0x5aed instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00140004: 0x2b34 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00140008: 0xf233 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0014000c: 0x757e instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00140010: 0xf57d instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00140014: 0x578e instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00140018: 0xf92a instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0014001c: 0x4b0e instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00140020: 0x947f instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00140024: 0x1cfc instead Further such events for this erase block will not be printed jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00160000: 0x3511 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00160004: 0x7632 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00160008: 0x8ece instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0016000c: 0x7122 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00160010: 0x3ce8 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00160014: 0x2bc9 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00160018: 0x9c64 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0016001c: 0x3e27 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00160020: 0x1b01 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00160024: 0x8d8b instead Further such events for this erase block will not be printed Old JFFS2 bitmask found at 0x00169680 You cannot use older JFFS2 filesystems with newer kernels jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00180000: 0xf50a instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00180004: 0xe459 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00180008: 0x6cd7 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0018000c: 0x6337 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00180010: 0xfc63 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00180014: 0xebcf instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00180018: 0x4fdb instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0018001c: 0x1877 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00180020: 0x038f instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00180024: 0x37ee instead Further such events for this erase block will not be printed jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001a0000: 0x6e1c instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001a0004: 0x06c1 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001a0008: 0x9ceb instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001a000c: 0x0635 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001a0010: 0x0552 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001a0014: 0xebda instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001a0018: 0x7705 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001a001c: 0xf45d instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001a0020: 0x0862 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001a0024: 0x4fb3 instead Further such events for this erase block will not be printed Old JFFS2 bitmask found at 0x001a8e90 You cannot use older JFFS2 filesystems with newer kernels Old JFFS2 bitmask found at 0x001ba1b4 You cannot use older JFFS2 filesystems with newer kernels jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001c0000: 0x1373 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001c0004: 0x91f4 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001c0008: 0x6cd5 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001c000c: 0x32ad instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001c0010: 0x93e1 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001c0014: 0xbf13 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001c0018: 0xb0d9 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001c001c: 0x5602 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001c0020: 0x7d8b instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001c0024: 0x177d instead Further such events for this erase block will not be printed jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001e0000: 0x46b9 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001e0004: 0x7fb8 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001e0008: 0x9bef instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001e000c: 0x2aa8 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001e0010: 0x2fcd instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001e0014: 0xdef4 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001e0018: 0x2645 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001e001c: 0xb126 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001e0020: 0x8f6d instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x001e0024: 0x80e9 instead Further such events for this erase block will not be printed jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00200000: 0xa3a9 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00200004: 0x1884 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00200008: 0xa7aa instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0020000c: 0xae7a instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00200010: 0xb5f0 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00200014: 0xe4bd instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00200018: 0x90af instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0020001c: 0x20a2 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00200020: 0x5579 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00200024: 0x020f instead Further such events for this erase block will not be printed jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00220000: 0x175c instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00220004: 0x291c instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00220008: 0x0935 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0022000c: 0x8c72 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00220010: 0x974e instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00220014: 0x317e instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00220018: 0xc4f3 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0022001c: 0xfc3b instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00220020: 0x1615 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00220024: 0x2b1f instead Further such events for this erase block will not be printed Old JFFS2 bitmask found at 0x00231608 You cannot use older JFFS2 filesystems with newer kernels jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00240000: 0xb9da instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00240004: 0x86fe instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00240008: 0x6cdb instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0024000c: 0x9da7 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00240010: 0x7185 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00240014: 0x112c instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00240018: 0xb3af instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0024001c: 0x6b1e instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00240020: 0x33e3 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00240024: 0x3aa8 instead Further such events for this erase block will not be printed jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01fa0000: 0x4c2e instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01fa0004: 0x534b instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01fa0008: 0x302e instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01fa000c: 0x3030 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01fa0010: 0x4537 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01fa0014: 0x3033 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01fa0018: 0x2020 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01fa001c: 0x2020 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01fa0020: 0x4531 instead jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x01fa0024: 0x3437 instead Further such events for this erase block will not be printed Empty flash at 0x01fa0100 ends at 0x01fa0800 VFS: Mounted root (jffs2 filesystem) readonly on device 31:8. devtmpfs: mounted Freeing unused kernel memory: 228k freed ********************************************************************************* _ _ __ _ __ _____ __ __ _____ | | | || \ | | / // ____]\ \ / // ____]TM | | | || \ | | / /| (___ \ V /| (____ | | | || |\ \| |\ \ \____ \ \ / \____ \ | |_____ | || | \ | \ \ ____) | | | ____) | |_______||_||_| \__| \_\[____ / |_| [_____/ (c) 2013 Belkin International, Inc. and/or its affiliates. All rights reserved. Booting atlanta (firmware version 1.0.7.181820) ********************************************************************************* [utopia][init] System Initialization [utopia][init] Creating /proc [utopia][init] Creating /sys [utopia][init] Creating /dev [utopia][init] Creating /tmp [utopia][init] Allocating 40M for /tmp [utopia][init] Prepairing /dev/pts [utopia][init] Setting /tmp and /var permissions [utopia][init] Starting udev.. bdutil board utility kernel module, version 1.4 bdutil board utility kernel module boardId (0) bdutil board utility LED kernel module, version 1.0 Attempting mount of ubifs syscfg partition UBI device number 0, total 360 LEBs (45711360 bytes, 43.6 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) [utopia][init] Using persistent syscfg data from /var/config/syscfg [utopia][init] Starting system logging [utopia][init] Starting sysevent subsystem net.netfilter.nf_conntrack_acct = 1 [utopia][init] Setting any unset system values to default [utopia][init] no persistence config file (/var/config/pstcfg) found setting up MAC addresses for all interface based on 14:91:82:61:A1:94 Updating NTP Servers if necessary Unit Model (EA7300) matches Firmware image (EA7300) Checking WAN supported connection type Set port 0 pvid 2. Set port 5 pvid 2. switch reg write offset=2004, value=ff0003 switch reg write offset=2104, value=ff0003 switch reg write offset=2204, value=ff0003 switch reg write offset=2304, value=ff0003 switch reg write offset=2404, value=ff0003 switch reg write offset=2504, value=ff0003 switch reg write offset=2604, value=ff0003 wifi, set wifi hw nat start vlan now... checking for interactive script start up... Updating BootCount Page[29]:E800 ... Done [utopia][init] Starting bdutil daemon attempting to sync sysinfo.cgi auth credentials BDUTIL daemon mode (Focus/MTK) Wed Mar 28 11:07:00 UTC 2018 wan, sysevent received: wan-start (none) login: Set port 0 pvid 2. Set port 5 pvid 2. switch reg write offset=2004, value=ff0003 switch reg write offset=2104, value=ff0003 switch reg write offset=2204, value=ff0003 switch reg write offset=2304, value=ff0003 switch reg write offset=2404, value=ff0003 switch reg write offset=2504, value=ff0003 switch reg write offset=2604, value=ff0003 wifi, set wifi hw nat start vlan now... wifi, sysevent received: lan-started wifi, service_start() Lighttpd Model Base: EA7300 Generating Rainier lighttpd config wifi, wifi_onetime_setting wifi, loading Wi-Fi driver Build temporary www configuration directory: TSLIIHauhEfGE Power cycle Ethernet ports. [utopia] Not setting ppp_clamp_mtu wifi, SingleSKU: /etc/7615_SingleSKU.dat_FCC, SingleSKUBF: /etc/7615_SingleSKU_BF.dat_FCC wifi cache: saving wl0 physical settings wifi, set wifi hw nat wifi cache: saving wl1 physical settings Channel list is available. Do nothing wifi cache: saving wl0 virtual settings wifi cache: saving wl1 virtual settings wifi cache: saving wl0 guest settings wifi cache: saving wl1 guest settings wifi cache: saving wl0 simpletap settings wifi cache: saving wl1 simpletap settings killall: iwevent: no process killed Waiting for Wireless Events from interfaces... wifi, REGION: US wifi, ETxBfEnCond 0 wifi, ETxBfEnCond 1 wifi, MU-MIMO enabled wifi, PMF disabled wifi, HT_RDG 1 wifi, 256QAM disabled wifi, BGProtection 1 wifi, ra0 setting rts thresh wifi, HT_STBC 0 wifi, VHT_STBC 0 wifi, ra0 htduplicate enabled wifi, ra0 setting framentation thresh wscd: SSDP UDP PORT = 1900 wifi, TxBurst 1 wifi, wifi_physical_start(ra0) wifi, wifi_virtual_start(ra0) wifi, wifi_user_start(ra0) Registering Service myrouter._http._tcp.local port 80 Got a reply for myrouter._http._tcp.local.: Name now registered and active Not ready for JNAP. Sleeping for 15 seconds... [utopia] Not setting ppp_clamp_mtu on dslite protocol file_sharing, smp wifi eth2/eth3 RPS: CPU0/2 Restarting nfqrecv service... wifi, ra0 is up wan, sysevent received: phylink_wan_state wifi, wifi_guest_start(ra0) wifi, guest or user vap is disabled, do not start wifi guest ra1 wifi, REGION: US wifi, ETxBfEnCond 0 wifi, ETxBfEnCond 1 wifi, MU-MIMO enabled wifi, PMF disabled wifi, HT_RDG 1 wifi, 256QAM disabled wifi, rai0 VhtBw=1 (80 MHz) wifi, rai0 setting rts thresh wifi, HT_STBC 1 wifi, VHT_STBC 0 wifi, rai0 htduplicate enabled wifi, rai0 setting framentation thresh wscd: SSDP UDP PORT = 1900 wifi, TxBurst 1 wifi, wifi_physical_start(rai0) wifi, wifi_virtual_start(rai0) wifi, wifi_user_start(rai0) wifi, set wifi hw nat wifi, rai0 is up wifi, wifi_guest_start(rai0) wifi, guest or user vap is disabled, do not start wifi guest rai1 route: SIOCADDRT: File exists wifi, restart wscd killall: wscd: no process killed wscd: SSDP UDP PORT = 1900 wifi, set wifi hw nat [fw.sh] fwup_checked_after_boot: 0 [fwupd] status details:"ERROR: Connecting server" [fw.sh] fwup_forced_update: 0 file_sharing, smp wifi eth2/eth3 RPS: CPU0/2 Starting smbd ... wifi, smp wifi wscd: SSDP UDP PORT = 1900 eth2/eth3 RPS: CPU0/2 [fw.sh] fwup_checked_after_boot: 0 [fwupd] status details:"ERROR: Connecting server" [fw.sh] fwup_forced_update: 0 [fw.sh] fwup_checked_after_boot: 0 [fwupd] status details:"ERROR: Connecting server" [fw.sh] fwup_forced_update: 0 [fw.sh] fwup_checked_after_boot: 0 [fwupd] status details:"ERROR: Connecting server" [fw.sh] fwup_forced_update: 0 \\ ==== OpenWrt bootlog ==== LoadAddr=80a00000 NetBootFileXferSize= 0044b465 Automatic boot of image at addr 0x80A00000 ... ## Booting image at 80a00000 ... Image Name: MIPS OpenWrt Linux-4.14.125 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 4502565 Bytes = 4.3 MB Load Address: 80001000 Entry Point: 80001000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 256 Starting kernel ... [ 0.000000] Linux version 4.14.125 (shirata@openwrt-dev) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7783-85eda6f)) #0 SMP Sat Jun 15 17:05:30 2019 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is Linksys EA7300 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] random: get_random_bytes called from start_kernel+0x94/0x4b0 with crng_init=0 [ 0.000000] percpu: Embedded 14 pages/cpu s26192 r8192 d22960 u57344 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Writing ErrCtl register=000101f0 [ 0.000000] Readback ErrCtl register=000101f0 [ 0.000000] Memory: 250872K/262144K available (4487K kernel code, 232K rwdata, 992K rodata, 2724K init, 248K bss, 11272K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS: 256 [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns [ 0.007801] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.073971] pid_max: default: 32768 minimum: 301 [ 0.078737] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.085246] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.094000] Hierarchical SRCU implementation. [ 0.099135] smp: Bringing up secondary CPUs ... [ 0.116618] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.116628] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.116640] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.116771] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.163879] Synchronize counters for CPU 1: done. [ 0.210393] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.210402] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.210411] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.210484] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.254979] Synchronize counters for CPU 2: done. [ 0.297720] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.297728] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.297737] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.297815] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.340156] Synchronize counters for CPU 3: done. [ 0.370014] smp: Brought up 1 node, 4 CPUs [ 0.377513] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.387298] futex hash table entries: 1024 (order: 3, 32768 bytes) [ 0.393578] pinctrl core: initialized pinctrl subsystem [ 0.399285] NET: Registered protocol family 16 [ 0.413427] pull PCIe RST: RALINK_RSTCTRL = 4000000 [ 0.718646] release PCIe RST: RALINK_RSTCTRL = 7000000 [ 0.723694] ***** Xtal 40MHz ***** [ 0.727050] release PCIe RST: RALINK_RSTCTRL = 7000000 [ 0.732148] Port 0 N_FTS = 1b105000 [ 0.735614] Port 1 N_FTS = 1b105000 [ 0.739057] Port 2 N_FTS = 1b102800 [ 1.894248] PCIE2 no card, disable it(RST&CLK) [ 1.898606] -> 21007f2 [ 1.901010] PCIE0 enabled [ 1.903603] PCIE1 enabled [ 1.906204] PCI host bridge /pcie@1e140000 ranges: [ 1.910980] MEM 0x0000000060000000..0x000000006fffffff [ 1.916138] IO 0x000000001e160000..0x000000001e16ffff [ 1.921339] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000 [ 1.936579] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 1.942436] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 1.948145] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 1.955179] PCI host bridge to bus 0000:00 [ 1.959211] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.966067] pci_bus 0000:00: root bus resource [io 0xffffffff] [ 1.971899] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 1.978657] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.988615] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 1.995168] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 2.002041] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 2.008634] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 2.015525] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 2.022278] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] [ 2.028995] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] [ 2.035761] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff] [ 2.042491] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 2.049767] pci 0000:00:00.0: PCI bridge to [bus 01] [ 2.054662] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 2.061429] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit] [ 2.068668] pci 0000:00:01.0: PCI bridge to [bus 02] [ 2.073598] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] [ 2.081595] clocksource: Switched to clocksource GIC [ 2.088143] NET: Registered protocol family 2 [ 2.093187] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 2.100073] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 2.106521] TCP: Hash tables configured (established 2048 bind 2048) [ 2.112918] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 2.118684] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 2.125149] NET: Registered protocol family 1 [ 4.551556] 4 CPUs re-calibrate udelay(lpj = 2924544) [ 4.557783] Crashlog allocated RAM at address 0x3f00000 [ 4.563245] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 4.575357] random: fast init done [ 4.576537] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 4.584494] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 4.597569] io scheduler noop registered [ 4.601407] io scheduler deadline registered (default) [ 4.607639] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 4.615267] console [ttyS0] disabled [ 4.618808] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A [ 4.627837] console [ttyS0] enabled [ 4.627837] console [ttyS0] enabled [ 4.634708] bootconsole [early0] disabled [ 4.634708] bootconsole [early0] disabled [ 4.643304] cacheinfo: Failed to find cpu0 device node [ 4.648430] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 4.655305] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error [ 4.662399] Enable NFI Clock [ 4.665270] # MTK NAND # : Use HW ECC [ 4.668928] Device not found, ID: c2f1 [ 4.672672] Not Support this Device! [ 4.676401] chip_mode=00000001 [ 4.679439] Support this Device in MTK table! c2f1 [ 4.684400] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 [ 4.690858] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 4.697189] nand: Macronix NAND 128MiB 3,3V 8-bit [ 4.701889] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 4.709439] Scanning device for bad blocks [ 4.953646] 12 fixed-partitions partitions found on MTD device MT7621-NAND [ 4.960486] Creating 12 MTD partitions on "MT7621-NAND": [ 4.965806] 0x000000000000-0x000007f80000 : "all" [ 4.972574] 0x000000000000-0x000000080000 : "u-boot" [ 4.978506] 0x000000080000-0x0000000c0000 : "u-boot-env" [ 4.984816] 0x0000000c0000-0x000000100000 : "factory" [ 4.990823] 0x000000100000-0x000000140000 : "s-env" [ 4.996721] 0x000000140000-0x000000180000 : "devinfo" [ 5.002810] 0x000000180000-0x000002980000 : "kernel1" [ 5.009173] 0x000000580000-0x000002980000 : "rootfs1" [ 5.015477] 0x000002980000-0x000005180000 : "kernel2" [ 5.021899] 0x000002d80000-0x000005180000 : "rootfs2" [ 5.028235] 0x000005180000-0x000005280000 : "sysdiag" [ 5.034306] 0x000005280000-0x000007f80000 : "syscfg" [ 5.040619] [mtk_nand] probe successfully! [ 5.045424] Signature matched and data read! [ 5.049673] load_fact_bbt success 1023 [ 5.054164] libphy: Fixed MDIO Bus: probed [ 5.124133] libphy: mdio: probed [ 6.545023] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver [ 6.551716] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19 [ 6.562456] NET: Registered protocol family 10 [ 6.568404] Segment Routing with IPv6 [ 6.572199] NET: Registered protocol family 17 [ 6.576680] 8021q: 802.1Q VLAN Support v1.8 [ 6.583278] hctosys: unable to open rtc device (rtc0) [ 6.598353] Freeing unused kernel memory: 2724K [ 6.602955] This architecture does not have kernel memory protection. [ 6.620654] init: Console is alive [ 6.624387] init: - watchdog - [ 6.635909] kmodloader: failed to mmap /lib/modules/4.14.125/mt7615.ko [ 6.661921] init: - preinit - [ 6.782790] mtk_soc_eth 1e100000.ethernet: PPE started Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.475358] mtk_soc_eth 1e100000.ethernet eth0: port 3 link up [ 9.909375] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818 [ 9.923448] procd: - early - [ 9.926423] procd: - watchdog - [ 10.581723] procd: - watchdog - [ 10.585159] procd: - ubus - [ 10.592938] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.642268] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.648964] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.656175] procd: - init - Please press Enter to activate this console. [ 10.786221] kmodloader: failed to mmap /lib/modules/4.14.125/mt7615.ko [ 11.881403] urandom_read: 5 callbacks suppressed [ 11.881414] random: jshn: uninitialized urandom read (4 bytes read) [ 11.938935] random: jshn: uninitialized urandom read (4 bytes read) [ 17.241881] mtk_soc_eth 1e100000.ethernet: PPE started [ 17.253044] br-lan: port 1(eth0.1) entered blocking state [ 17.258451] br-lan: port 1(eth0.1) entered disabled state [ 17.264405] device eth0.1 entered promiscuous mode [ 17.269274] device eth0 entered promiscuous mode [ 17.277766] br-lan: port 1(eth0.1) entered blocking state [ 17.283226] br-lan: port 1(eth0.1) entered forwarding state [ 17.289273] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 18.311898] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 22.192431] random: crng init done BusyBox v1.28.4 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt 18.06-SNAPSHOT, r7783-85eda6f ----------------------------------------------------- \\ ===== Notes ===== //Space for additional notes, links to forum threads or other resources.// * ... ===== Tags ===== [[meta:tags|How to add tags]] {{tag>ramips MT7621 2core 4thread 128NAND 256RAM 5port GigabitEthernet 2wnic 3x3 MT7615 802.11bgn 802.11anac 802.11ac wifi5 3ant NondetachableAntenna InternalAntenna Dual_firmware 1USB USB3.0 U-boot Serial 12v_powered}}