Open Source Serial Software - Page 2

GUI software for sending, receiving and logging data from serial ports

Columbo Simple Serial Library is an easy to use, event driven serial port communication library for Linux.

Dzcomm is an RS-232 API for as many OS / platforms as we can achieve. Originally designed to work on DOS alongside the allegro games programming library it can now work work alongside it as well as independently of it and works on some unixes as well.

FUNterm is a serial port terminal program for Windows. It offers basic serial connection. Because FUNterm is written using basic Win32 calls, with no high-level libraries, it works under Linux using Wine. The serial driver can be used separately.

GUMA is a GPRS-Gateway written in C#. It contains a terminal for serial communication, phonecall-screen, SMS-Screen to send SMS from GPRS USB-Modem to GPRS phone. Param: Port, Baud, Parity, Data-/Stopbits, Write-/Readtimeout, Pin.

ILM is a utility for the ISDN Line Monitor, an ISDN line monitoring hardware sold by many dealers in central europe. (e.g. Conrad and EgTel). It provides functions to: - retrieve all recorded information - erase all recorded information - config

This service listens for incoming TELNET network connections. When a connection on the network port is received, the corresponding serial port is opened and the data between the two ports is redirected. When the network connection is closed, the serial port is closed and the service begins listening for another network connection.

OS X RS232 Serial monitor program for sending and receiving data and monitoring and controlling the handshake signals. It can be used for debugging serial connections, serial device drivers, embedded systems connected to the serial etc.

This library was designed to send commands and receive analog to digital sensor input from a Pontech SV203 microcontroller board. The library consists of one primary class (SV203) and several support files. This has functions to control all servo funct

Provides access to a GPS device, fully written in perl

Serial terminal based on QT library.

A real-time serial port device driver, works with RT-Linux and RTAI.

Secom is an object-oriented library of portable, reusable components for communicating over serial devices. With secom you can develop an application that will compile and execute on Posix and Windows, with little to no changes to the source code.

ttypatch is a Linux application that permits two or more "serial port user programs" to reliably connect to each other without the use of actual serial ports. Also acts as a virtual patch panel among any number of real and virtual serial ports.

Serial Debugger, moninter and control the behavior of the serial ports.

Simple Serial COM read/write program. I needed it for Caller ID read modem driver so it has command auto complete for AT commands. It is a good replacement for HyperTerminal. Made for .NET Framework 2.0

PROJECT MOVED TO: https://github.com/damogranlabs/serial-tool See releases page: https://github.com/damogranlabs/serial-tool/releases Serial Tool is a utility for developing serial communications, custom protocols or device testing. You can set up bytes to send accordingly to your protocol and save configuration to a file – which can be used another time. You can send multiple byte arrays, you can send sequence of different byte arrays and put delay between them. You can read data in HEX or ASCII. You can even write a note to yourself like: “CH1: toggle LED 1”.

This application is a ASCII-based data scope. When used with a 'spy' cable such as the CBL-Full-1A product from www.commfront.com this progrmam shows the ASCII chars on both sides of a comm link. There are three main tabs on the user interface. The 'Vertical' tab displays the comm link conversation in a vertically-scrolling half-duplex mode. Each 'side' of the conversation is detected by the user-configured 'start msg' and 'end msg' byte sequence. The 'Horizontal' tab shows bytes, one at a time, as they are received on each side of the link so the relative timing relationships can be monitored. Printable ASCII chars are shown. Non-printable are shown with a '0x' prefix. The two sides of this link referred to as 'Port 1' and 'Port 2'. Each side must communicate at the same baud rate. Each side can have its' own start message and end message character configurations. A log tab where state and error messages can be reviewed.

System tray caller id applet for Windows based on .NET framework. Turns on caller ID function of the modem, and when any output occurs (a call comes in), a small log window appears showing all text, verbatim.

The Clans was a popular game written for online BBSes back in the day of their great popularity. It is a text-based game featuring inter-BBS communications. It was written initially for Turbo C++, but has been ported to gcc and MSVC

USPUI-Universal Serial Port User Interface WxWidgets based grfic user interface for serial port. You can define the interface by simple configuration file.

catty is a small utility to write+read to+from a serial tty device. You can use it in scripts, or directly writing some text to its stdin. With catty you can add in a few seconds serial communication to your shell scripts.

This software, consisting of a daemon and a command shell, is meant to be used together with the Xtreme GM7 GPS tracker to help simplify its management and to make it possible to monitor alerts sent by the tracker. The software is intended to be run as a GNU/Linux service that always runs in the background and can be used to both receive location updates from a remote tracker as well as configuring the tracker (over both USB and a GPRS link to the device). All received events are stored in a database and the daemon supports export of events to GPX, KML, CSV format. It is also possible to have specific action scripts executed upon receiving specific events or generate mail notifications. The daemon and command shell comes with extensive reference documentation (HTML & PDF) and Unix man pages.

asynchronous Garmin GPS communication C library for PalmPilot

Telnet to serial gateway for embedded development