Start Your Crop off Right
Innovative. Precise. Efficient. Set the stage for maximum yield potential with John Deere’s tillage line — designed to deliver highly productive solutions backed by the latest in precision ag technologies. Proper tillage practices provide the opportunity to place seed at the correct depth so you can enable uniform crop emergence. When executed correctly, tillage can increase yield and reduce loss risk on your farm by providing value with residue, weed, and soil compaction management along with seedbed preparation.
Chisel Plows and Coulter Chisels
- Fall
Best choice for:
Primary pass to manage compaction and residue.
Available Models:
Rippers
- Fall
Best choice for:
Managing compaction, sizing residue, and leveling the field.
Available Models:
Min-Till Rippers and Subsoilers
- Fall
Best choice for:
Managing compaction and minimizing disturbance.
CC Series Coulter Chisels
We designed the CC Series from the ground up, so you could have a highly productive primary tillage tool that tackles varying crop conditions with minimal operator input or adjustments. With a wide range of sizes offered, there is a CC Series model for your operation — whether it's a new tractor, or one that has been on the farm for years. Loaded with the newest John Deere precision ag technologies to keep your productivity levels at peak performance, the CC Series features TruSet™ Active and is Autonomy Ready from the factory.
Tech for the Future. From the Ground Up.
You have options to farm your way. The new CC Series Coulter Chisel is Autonomy Ready, with precision ag technologies like TruSet™ Active, AutoPath™ and AutoTrac™ Turn Automation, so you can make data-driven decisions for your operation, reduce operator error, and meet your daily challenges on the field with little operator input.
Compare our Chisel Plows and Coulter Chisels
| Models | Working Depth | Working Speed | Required HP (PTO) | Residue Management | Residue Conditions | Depth Control |
|---|---|---|---|---|---|---|
| Working Depth
up to 12 in. | Working Speed
5 to 7 mph | Required HP (PTO)
6 to 14 HP/FT | Residue Management
fracture/mix | Residue Conditions
medium/heavy | Depth Control
3pt hitch |
|
| Working Depth
up to 12 in. | Working Speed
5 to 7 mph | Required HP (PTO)
7 to 14 HP/FT | Residue Management
fracture/mix | Residue Conditions
medium/heavy | Depth Control
TruSet/Single-point |
|
| Working Depth
6 to 8 in. | Working Speed
6 to 7 mph | Required HP (PTO)
20 to 25 HP/FT | Residue Management
fracture/mix | Residue Conditions
Medium / Heavy | Depth Control
TruSet/Single-point |
|
| Working Depth
6 to 8 in. | Working Speed
6 to 7 mph | Required HP (PTO)
20 to 25 HP/FT | Residue Management
fracture/mix | Residue Conditions
Medium / Heavy | Depth Control
TruSet/Single-point |
|
| Working Depth
6 to 8 in. | Working Speed
6 to 7 mph | Required HP (PTO)
20 to 25 HP/FT | Residue Management
fracture/mix | Residue Conditions
Medium / Heavy | Depth Control
TruSet/Single-point |
|
| Working Depth
6 to 8 in. | Working Speed
6 to 7 mph | Required HP (PTO)
20 to 25 HP/FT | Residue Management
fracture/mix | Residue Conditions
Medium / Heavy | Depth Control
TruSet/Single-point |
|
| Working Depth
6 to 8 in. | Working Speed
6 to 7 mph | Required HP (PTO)
20 to 25 HP/FT | Residue Management
fracture/mix | Residue Conditions
Medium / Heavy | Depth Control
TruSet/Single-point |
Disks
The toughest gang around
From planning to harvest, you can count on John Deere tillage tools to build the foundation that next year's yields will stand upon.
Compare our Disks and Vertical Tillage
| Models | Working Depth | Working Speed | Required HP (Engine)/FT | Weight /blade* | Residue Conditions | Depth Control |
|---|---|---|---|---|---|---|
| Working Depth
3.5 in (88.9 mm) | Working Speed
8 to 10 mph (13 - 16 km/h) | Required HP (Engine)/FT
10-14/ft. (24.5 - 34.25 kw/m) | Weight /blade*
Estimated Avg 260 lbs (118 kg) | Residue Conditions
light/medium/heavy | Depth Control
TruSet/Single Point |
|
| Working Depth
up to 3 in (76 mm) | Working Speed
7 to 10 mph (11.4-16 km/h) | Required HP (Engine)/FT
8.5 to 11 (20.8-26.95 kw/m) | Weight /blade*
197 lbs to 227 lbs (89.4-103 kg) | Residue Conditions
light/medium/heavy | Depth Control
TruSet/Single point |
|
| Working Depth
2-6 inches (51-152 mm) | Working Speed
10 to 14 mph (16-22.5 km/h) | Required HP (Engine)/FT
11-15/ft. (26.9-36.7 kw/m) | Weight /blade*
210 - 380 lbs (95.25-172.4 kg) | Residue Conditions
light/medium/heavy | Depth Control
TruSet Set-Point Depth/ Single-Point |
|
| Working Depth
2-6 inches | Working Speed
10 to 14 mph | Required HP (Engine)/FT
15+ hp | Weight /blade*
306 lbs to 388 lbs | Residue Conditions
light/medium/heavy | Depth Control
TruSet Set-Point Depth |
|
| Working Depth
2-6 inches (51- 152 mm) | Working Speed
10 to 14 mph (16-22.5 km/h) | Required HP (Engine)/FT
15+ hp (36.7 kW/m) | Weight /blade*
306 lbs to 388 lbs (138.8-176 kg) | Residue Conditions
light/medium/heavy | Depth Control
TruSet Set-Point Depth |
|
| Working Depth
2-6 inches (51- 152 mm) | Working Speed
10 to 14 mph (16-22.5 km/h) | Required HP (Engine)/FT
15+ hp (36.7 kW/m) | Weight /blade*
306 lbs to 388 lbs (138.8-176 kg) | Residue Conditions
light/medium/heavy | Depth Control
TruSet Set-Point Depth |
|
| Working Depth
2-6 inches (51- 152 mm) | Working Speed
10 to 14 mph (16-22.5 km/h) | Required HP (Engine)/FT
15+ hp (36.7 kW/m) | Weight /blade*
306 lbs to 388 lbs (138.8-176 kg) | Residue Conditions
light/medium/heavy | Depth Control
TruSet Set-Point Depth |
|
| Working Depth
2-6 inches (51- 152 mm) | Working Speed
10 to 14 mph (16-22.5 km/h) | Required HP (Engine)/FT
15+ hp (36.7 kW/m) | Weight /blade*
306 lbs to 388 lbs (138.8-176 kg) | Residue Conditions
light/medium/heavy | Depth Control
TruSet Set-Point Depth |
|
| Working Depth
2-6 inches (51- 152 mm) | Working Speed
10 to 14 mph (16-22.5 km/h) | Required HP (Engine)/FT
15+ hp (36.7 kW/m) | Weight /blade*
306 lbs to 388 lbs (138.8-176 kg) | Residue Conditions
light/medium/heavy | Depth Control
TruSet Set-Point Depth |
|
| Working Depth
2-6 inches (51- 152 mm) | Working Speed
10 to 14 mph (16-22.5 km/h) | Required HP (Engine)/FT
15+ hp (36.7 kW/m) | Weight /blade*
306 lbs to 388 lbs (138.8-176 kg) | Residue Conditions
light/medium/heavy | Depth Control
TruSet Set-Point Depth |
|
| Working Depth
up to 5 in (127 mm) | Working Speed
5 to 7 mph (8-11.3 km/h) | Required HP (Engine)/FT
7 to 11 (17.15-26.95 kw/m) | Weight /blade*
179 lbs to 209 lbs (81.2-94.8 kg) | Residue Conditions
light/medium | Depth Control
TruSet/Single-point |
|
| Working Depth
up to 6 in (152 mm) | Working Speed
5 to 7 mph (8-11.3 km/h) | Required HP (Engine)/FT
7 to 11 (17.15-26.95 kw/m) | Weight /blade*
201 lbs to 243 lbs (91.2-110.2 kg) | Residue Conditions
light/medium/heavy | Depth Control
TruSet/Single-point |
|
| Working Depth
up to 8 in (203 mm) | Working Speed
5 to 7 mph (8-11.3 km/h) | Required HP (Engine)/FT
9 to 12 (22.05-29.4 kw/m) | Weight /blade*
280 lbs to 286 lbs (127-129.7 kg) | Residue Conditions
medium/heavy | Depth Control
TruSet/Single-point |
*Measured with base configuration; exact weight per blade is dependent on configuration.
MonTag Overseeder for 2660VT
Now your 2660VT can broadcast dry material without pulling additional tanks or carts. Introducing the new cover crop seeder for the 2660VT from MonTag Mfg. The metering system fits conveniently onto the frame of the 30-foot 3-inch 2660VT without sacrificing any transport dimensions. Using MonTag’s metering system and controlled with only one additional SCV, tank sizes of 30 or 50 cubic feet give you the ability to apply up to 500 lb (227 kg) per acre of dry material.
Compare our Field Cultivators & Mulch Finishers
| Models | Working Depth | Working Speed | Required HP (PTO)/FT | Spacing Option | Residue Conditions | Depth Control |
|---|---|---|---|---|---|---|
| Working Depth
up to 5 in (127 mm) | Working Speed
10 to 16 km/h | Required HP (PTO)/FT
8-12 (19.6-29.4 kw/m) | Spacing Option
6 in (152 mm) split-the-middle / 9 in (229 mm) / S-tine 4.5 in (114 mm) | Residue Conditions
light/medium | Depth Control
TruSet/Single-point |
|
| Working Depth
up to 5 in (127 mm) | Working Speed
10 to 16 km/h | Required HP (PTO)/FT
8-12 (19.6-29.4 kw/m) | Spacing Option
6 in (152 mm) split-the-middle / 9 in (229 mm) / S-tine 4.5 in (114 mm) | Residue Conditions
light/medium | Depth Control
TruSet/Single-point |
|
| Working Depth
up to 6 in (152 mm) | Working Speed
10 to 16 km/h | Required HP (PTO)/FT
10-14 (24.5-34.2 kw/m) | Spacing Option
9 in (229 mm) split-the-middle | Residue Conditions
N/A | Depth Control
TruSet/Single-point |
Min-Till Rippers and Subsoilers
Battle compaction with minimal operator input with John Deere’s improved in-line ripping tool series. Extended wear standards deliver twice the life expectancy*. Choose from drawn or integral models with sizes to match your tractor.
*Compared to previous models.
Images of equipment models may be digitally generated, are for illustration purposes only, and are subject to change. Equipment models shown are typically base models and may not reflect all features, options, or attachments. Equipment availability may be limited. See your John Deere dealer for additional information.
Compare our Min-Till Rippers
| Models | Working Depth | Working Speed | Required HP (PTO) | Residue Conditions | Depth Control |
|---|---|---|---|---|---|
| Working Depth
Up to 16 in (40.6 cm) | Working Speed
5 to 7 mph | Required HP (PTO)
50 to 60 hp | Residue Conditions
Medium/Heavy | Depth Control
TruSet / |
|
| Working Depth
Up to 16 in (40.6 cm) | Working Speed
5 to 7 mph | Required HP (PTO)
50 to 60 hp | Residue Conditions
Medium/Heavy | Depth Control
TruSet / |
|
| Working Depth
Up to 16 in (40.6 cm) | Working Speed
5 to 7 mph | Required HP (PTO)
50 to 60 hp | Residue Conditions
Medium/Heavy | Depth Control
TruSet / |
|
| Working Depth
Up to 16 in (40.6 cm) | Working Speed
5 to 7 mph | Required HP (PTO)
50 to 60 hp | Residue Conditions
Medium/Heavy | Depth Control
TruSet / |
Compare our Rippers
| Models | Working Depth | Working Speed | Required HP (PTO)/FT | Residue Management | Residue Conditions | Depth Control |
|---|---|---|---|---|---|---|
| Working Depth
up to 16 in (406 mm) | Working Speed
8-9.7 km/h | Required HP (PTO)/FT
35 to 55 (26.1-41 kW)/ standard | Residue Management
fracture/size/ mix/bury | Residue Conditions
Heavy | Depth Control
Single-point |
|
| Working Depth
up to 16 in (406 mm) | Working Speed
8 km/h | Required HP (PTO)/FT
335 to 620 * (250-462.5 kW) | Residue Management
fracture/size/ mix/bury | Residue Conditions
Heavy | Depth Control
TruSet/Single-point |
|
| Working Depth
up to 16 in (406 mm) | Working Speed
8 km/h | Required HP (PTO)/FT
30 to 40 / standard (22.3-29.8 kW) | Residue Management
fracture | Residue Conditions
Light/medium/heavy | Depth Control
3pt hitch |
Strip-Till Solutions
John Deere offers the precision and repeatability necessary for successful strip-tillage through our products and technology. The ST Series offers strip-till bars with configurations and options to fit your soil type, nutrient plan, application preference and more. Technology like AutoPath™ allows you to plant into the strips you tilled in fall.
Compare our Strip-Till Bars
| Model | Configurations | Spacing Options | Working Speed | Working Depth | Fertilizer Capacity |
|---|---|---|---|---|---|
| Configurations
Integral, Drawn | Spacing Options
Integral: | Working Speed
Integral: | Working Depth
Integral: | Fertilizer Capacity
Integral: |
|
| Configurations
Integral, Drawn | Spacing Options
Integral: | Working Speed
Integral: | Working Depth
Integral: | Fertilizer Capacity
Integral: |
|
| Configurations
Drawn | Spacing Options
20 in. (50.8 cm) or 22 in. (55.9 cm) | Working Speed
Coulters 9.7 to 16 km/h | Working Depth
Shanks up to 11" (27.9 cm) | Fertilizer Capacity
10 tons |
Compare our Moldboards
| Models | Working Depth | Working Speed | Required HP (PTO) | # of bottoms | Residue Conditions | Depth Control |
|---|---|---|---|---|---|---|
| Working Depth
up to 14 in (356 mm) | Working Speed
8 km/h | Required HP (PTO)
23 to 35 (16.4-26.1 kW)PTO HP/bottom | # of bottoms
5, 6, or 7 | Residue Conditions
medium/heavy | Depth Control
gauge wheels |
Compare Heavy Harrows
| Models | Engine Horsepower | Harrow Sections | Tine Size | Tine Spacing | Working Width |
|---|---|---|---|---|---|
|
HH50 | Engine Horsepower
285 - 325
| Harrow Sections
5 | Tine Size
5 bar: 26-in. (66 cm) by 5/8-in.(1.5 cm) | Tine Spacing
5 bar: 18-in. (46 cm) centers | Working Width
50 ft. (15 m) |
|
HH70 | Engine Horsepower
5 bar: 200 - 300 | Harrow Sections
7 | Tine Size
5 bar: 26-in. (66 cm) by 5/8-in.(1.5 cm) | Tine Spacing
5 bar: 18-in. (46 cm) centers | Working Width
70 ft. (21 m) |
|
HH82 | Engine Horsepower
5 bar: 300 - 350 | Harrow Sections
9 | Tine Size
5 bar: 26-in. (66 cm) by 5/8-in.(1.5 cm) | Tine Spacing
5 bar: 18-in. (46 cm) centers | Working Width
82 ft. (25 m) |
Select, Build & Price
Select Your Tillage Solution
The broadest portfolio in our history.
Build & Price
Customize your new John Deere Tillage equipment for your unique needs with options, attachments, and accessories.
Operations Center
Data matters, now more than ever. That’s why we built Operations Center – the industry’s leading cloud-based farm management system. Securely collect, organize, and analyze your ag data… and view or share it with trusted advisors anytime, anyplace. When improving yields and profits matter, only Operations Center brings your connected machines together so you can Gain Ground every season, every field, every pass.