TONO

PMT-192
instruction manual

H i g a s h i n o E l e c t r i c C o r p o r a t i o n
9 8 T E L 0 2 7 2 ( 5 3 ) 1 2 2 1
M a e b a s h i - s h i G u m m a P r e f e c t u r e 3 7
ta ble of contents

1 Features of PMT - 192 14

2 Accessories
3 Handling Precautions 20

4 Parts Suspect 21
5 Connection (Be sure to make contact 22
with each instrument powered off.)
33
6 About external microphone
7 About accessory communication 37

software
8 Initialization of PMT-192
9 RS-232C baud rate (communication
speed of TNC and terminal quotient)
setting using communication software
DXTERM
10 Baud rate auto tracking setting
(There are things that can not be done
depending on the terminal model.)
11 Basic usage
12 After sales service
13 nuisance
14 Commands
15 Message
16 Looking at Health Counter
39
17 Control code
1 Features of PMT-192
• TNC • Wireless remote control is unnecessary because it is integrated with the
radio.
• There are two modes: FSK. GMSK (G3RUH connectable).
• VCO • Modulation is stable due to simultaneous conversion of crystal.
• 19200B (GMSK) operation is possible.
• The receiving filter is equipped with a wide (19200 B) / narrow (9600 B or less)
changeover.
• Volume • Squelch control is done with push switch (electronic volume
adoption).
• It can be operated as a normal radio wave by using an external microphone.
• Levitator operation is also possible.
The frequency, tone and offset frequency of the radio can be set from the
terminal (personal computer etc.).
8 waves of tone frequency OFF / 82.5 / 85.4 / 88.5 / 91.5 / 94.8 / 97.4 / 100.0
/ 103.5 Hz
Offset frequency 0 to ± 9.99 MHz
• Transmission output of the radio can be switched.
PMT-192H 20 W or 1 W PMT-192 L 10 W or 1 W
2 Accessories
instruction manual
Fuse 8A (PMT-192H) or 5A (PMT-192L)
Communication software
• Command list (1.44 MB / 3.5 inch FD 2 pcs)
Guarantee 赛
 (DXTERM is Mr. Morishige work; WTERM is written by Hiroo Inoue, LHA is
free software by Mr. Yoshiaki Yoshiaki)

3 Handling Precautions
• In the following cases, fire or malfunction may occur, so stop
using it immediately, disconnect the power s ource of this machine
and unplug the power supply plug from the AC outlet.

(1) In the event that the smoke from the main unit and the power
supply unit is off while the unit is in use

If there is a lightning strike nearby (Please do not disconnect

the antenna cable from this unit when it is in a lightning storm.)
Since the thunder has started to sound, there is a fear of
feeling, so it approaches this machine Please be careful not to
touch your hands.)

(1) In case of dropping this machine or giving a str ong impact

(1) When the fuse blows while using the machine

• Avoid using it in the following places.

- Places with high vibration and instability

(1) Outdoor places with high humidity and dust

A place where high temperature or direct sunlight is hit

In order to avoid the maritime confusion caused by Noise, please

use as far away as possible from personal computer • AV equipment
(TV • radio etc).
, • Do not disassemble.

(1) Since this unit uses many precision parts, please do not give
equilibrium, vi bration, etc. Also please do not touch or modify
parts other than the internal jumper switching.

• Power supply (Fire or malfunction may occur, so please be

careful enough

Well. )
Operation of single screw * The voltage is 12 VDC to 13.8 V. Do
not invert +/- by applying a voltage exceeding the source voltage
box.

(1) Use a power supply with a current capacity of 8 A (PMT - 192

H) or 5 A (PMT - 192 L) or more.

- T o p r e v e n t h e a t g e n e r a t i o n , f i r e , e t c . du e t o p o o r c o n t a c t e t c . , c o n n e c t
t h e p o w e r c o r d o f t h i s m a c h i n e s e c u r e l y t o th e t e r m i n a l o f t h e p o we r s u p p l y.
Also, please be careful not to cause connection failure, short circuit, etc.
w h e n e x t e n d i n g o r p r oc e s s i n g t h e p ow e r c o rd . ( W h e n e x t e nd i n g t he p o w e r c o rd
o f t h e m a i n p o w e r c o rd , p l e a s e u s e o n e w i th a t h i c k n e s s e q u a l to o r g r e a t e r
t h a n t h a t o f t h i s u n it . )

- A v o i d u s i n g i t wi t h t h e p o w e r c o r d b un d le d , a s i t m a y g e n er a te h e a t .

- S i n c e t h e c a s e ( c h a ss i s ) o f t h i s u n i t i s co n n e c t e d t o t h e m i n u s s i d e o f t he
power supply, please be careful not to cause short circuit by touching the
c h a s s i s w i t h t h e pl u s s i d e o f t h e p o w e r s up p l y .

♦ Strong Attention
In order to use a single shop, it is necessary to have an amateur radio kit
l i c e n s e f r o m t h e Mi n is t r y o f P o s t s a n d T e le c o m m u n i c a t i o n s .

( 1 ) T h e l a w s t i p u l a t es t h a t i t s h o u l d n o t in t e r c e p t w i r e l e s s c o mm u n i c a t i o n s
to be made to a specific counterparty, to leak its contents or content, or
t o s t e a l i t . P l e a se us e c o r r e c t l y .

(1) Since this unit becomes hot during use, use it in a well -ventilated area.
Y o u m a y g e t b u r n e d i f y o u r h a n d s a n d f ee t t o u c h i t .
( 1 ) I f y o u us e t h i s ma c h i n e b y p u t ti n g i t o n t o p o f a d u t y o r th e l i k e , i t
may cause damage to the duty detergent etc. or cause a fire due to the heat
g e n e r a t e d b y t h i s m a ch i n e .

( 1 ) P l a c i n g t h e u n i t n e a r o r o n a h e a t s o u r c e ( s u c h a s a s t o ve o r a c a r p e t )
m a y c a u s e a m a l f u nc t io n o r a f i r e .

I f y o u r i d e a si n g l e b ri d g e o r p l ac e a n o b j e ct , i t m a y c a u s e a b r e a kd o w n , b u r n,
or fire.

- I f y o u t o u c h t h e t ra n s m i t t e r o u t p u t c o n ne c t o r ( a n t e n n a t e r m i na l ) a n d t h e
a n t e n n a o f t h i s p r o du ct w h i l e s e nd i n g t h i s pr o d u c t , y o u m a y g e t b ur n e d b y h i gh
frequency.

(1) This machine has heavy weight. If it falls on the body, you may get injured.

- B e c a u s e t h e b a c k o f t h e c a s e o f t hi s m a c h in e i s a n g u l a r , y o u m a y g e t i n j u r ed
i f y o u b u m p y o u r ha n ds a n d f e e t .

( 1 ) I f y o u l i s t e n t o e a r p h o n e s o r h e a d p h o n es c o n n e c t e d t o t h e e x t e r n a l s p e e c h
j a c k o f t h i s m a c h in e , y o u m a y b e c a u g h t b y e a r s .

S i n c e o n e r a d i o c h a n n el u s e s r a d i o w a v e s , t h e r e a r e d e v i c e s
t h a t u s e r ad i o w a v e s i n t h e v i c i n i t y a n d t h e r e i s a
p o s s i b i l i t y o f t r i g g er i n g a b i g d e a l a n d a f f e c t i n g t h e
m a i n r i n g a n d t h e ir ar m s .

I f y o u u s e a s i ng l e p ie c e i n c l o s e p r o xi m i ty t o p r e c i s i o n
i n s t r u m e n t s or m e d i c al e q u i p m e n t , i t m a y af f e c t t h e se
i n s t r u m e n t s a n d c au s e d a m a g e .

( 1 ) A s d u s t a c c u m u l at e s o n t h i s m a c h i n e , i t w i l l c a u se
d a m a g e a n d f i r e , so pl e a s e c l e a n i t p e ri o di c a l l y .
P l e a s e d o n o t u s e a s i ng l e b o t t l e f o r a ny p u r po s e o t h e r t h a n
i t s o r i g i n a l p u r p os e .

( 1 ) T h i s m a c h i n e h o l ds m e m o r y w i t h a r e c h a rg e a b l e l i t h i u m
battery, so please note that the battery will be
d i s c h a r g e d i f t h e b a tt e r y i s d i s c h a r g e d i f t h e r e i s a
p e r i o d n o t t o u s e f o r 2 t o 3 m o n t h s a t a l l.

I f t u r n i n g O N / O F F t h e s i n g l e sw i t c h , pl e a s e w a i t f o r a b o u t
1 0 s e c o n d s a f t e r t u rn i n g i t O F F , p le a s e t u r n i t O N .
( R e p e a t e d l y tu r n i n g ON / O F F i n a s ho r t t ime m a y da m a g e
t h e m e m o r y c o n t e n ts . )

( 1 ) B e s u r e t o u s e t h e s p e c i f i e d c a b l e f o r co n n e c t i n g t h i s
u n i t t o t h e t e r m i n a l ( p e r s o n a l c o m p u t e r e tc . ) . U s i n g a
different one may damage the terminal and the terminal.

• Other

1 T h e c o m m a n d o f t h i s m a c h i n e i s l i c e n s e d f ro m T A P R ( T U S O N
A M A T E U R P A C K E T R AD I O CO U P . ) A n d h a s i t s o w n co m m a n d a d d e d
to fc. We also use licensed products from TAPR for the
clarification of the command and so on. (The command
version adopts AX.25 Level 2 Version 2.0 Release 1.1.8a.)
 Explanation of each part

1 • I t i s a p o w e r s w i t c h. W h e n r e d l i g h t t u r n s o n , t h e r ed l a m p l i g h t s
up.
2 . S w i t c h t h e t r a n s mis s i o n o u t p u t o f t h e ra d i o . ( L O i n a c o n c a ve
s t a t e : l o w b o w l / c o n vex w i t h H I • h i g h p o w e r ) T h e y e l l o w l a m p l i g h ts
w h e n L O , a n d t h e re d l a m p l i g h t s w h e n it is H I .
3 . A d j u s t t h e v o l u m e wh e n t h e i n t e r n a l s p e a ke r o r e x t e r n a l s p e a k er
is connected.
4 • A d ju s t t h e s q u e l c h. ( P r e s s - / + to u s e t he g r e e n l a m p d is a p p e a rs
a n d t h e n o i s e d i s ap p ea r s . )
5 • T h e r e d l a m p l i g h t s u p w h i l e d a t a f r o m t h e t e r m i n a l i s a c c u m u l a t ed
i n t h e un i t , a nd i t d i sa p p e a r s w h e n t r a n s m is si o n o f ac c u m u l a t e d d a ta
i s c o m p l e t e d . T h e A l a m p l i g h t s u p w h e n t h e l o c a l s t a t i o n a n d t he
r e m o t e s t a t i o n a r e i n t h e c o n n e c t e d s t at e .
6 • O u tp u t s t at u s is d i s p l a y e d w h e n t he h e a d s e t i s in t he
t r a n s m i s s i o n s t a t u s, an d t h e s i g n a l s t r e n g t h f r o m t h e r e m o t e s t a t i on
w h e n i t i s i n t h e r e ce p t i o n s t a t u s .
 5 Touch (Always make sure to connect each device
with its power turned off

ANTENNA
Ext speaker

All other are NC

PC or terminal

1 . Power supply， DC12 V〜13.8 V 8 A( PMT-192 H)or 5

A( PMT-192 L)
2. Coaxial cable in contact with the antenna should be as thick as
possible to reduce transmission loss. Also please use antenna with
430 MHz band and SWR 1.5 or less.
3 • For the RS - 232C cable to be connected to the terminal, please
use for the modem (one with straight K line). This machine is 25 bin
specifications.
4. The external microphone corresponds to that of Kenwood's 8 -pin
specification. (Only PTT and microphone signals can be used.)
5 • Use 8 Ohm for external speakers. (Using products smaller than 8
Ohm will cause malfunction.)
6 About external microphone
• T h e t y p e o f m i c r op h o n e t h a t c a n b e us e d i s a c o n d e n s e r

A view of the
microphone connector
viewed from this
direction
This wiring

In the case of condenser

microphone (microphone
amplifier)

Change like this

m i c r o p h o n e . ( D y n a mi c m i c r o p h o n e c a n n o t b e u s e d . )

• E v e n w i t h a c o nd e n se r m i c r o p h o n e m e a su r e c o n d u c t i o n b e t w e en
t h e 1 s t a n d 7 t h p i ns o f t he m i c ro p h o n e co n n e c t o r b e fo r e
c o n n e c t i n g i t to t h i s u n i t . I f c o n d u c ti n g , pl e a s e c h a n g e t he
l i n e a c c o r d i n g t o t h e fi g u r e . ( I f y o u c o n n e c t w i t h o u t c h a n g i n g
w i r i n g , t h i s u n i t w i ll r e m a i n t r a n s m i t ti n g. )
7 A b o u t a t t a c h e d co m mu n i c a t i o n s o f t w a r e
• T w o t y p e s o f c o m m u n i c a t i o n s o f t w a r e , D X T E RM a n d W T E R M , a r e i n c l u d e d
i n t h i s p r o d u c t . Yo u c a n o p e r a t e e i t h e r w ay . ( P l e a s e m o v e t he
c o m m u n i c a t i o n s o f t w a re t o t h e h a r d d i s k a n d u s e 3 M B o f f r e e h a r d d i s k
space.)
• H o w t o t r an s f e r DX TE R M ( F o r e x a m p l e , p u t t h e su p p l i e d f l o p p y d i s k
i n d r i v e E a n d t r an s fe r i t t o h a r d d i s k d ri v e A . )
( I n t h e c a s e o f W IN D OW S , r e t u r n t o D O S )

-A: \> E: <Enter> (It is not necessary if it is already in drive E.)

E: \> DO PLEASE NOTE – “\” symbols means backslash key. – tr.

- E : \ > D X I N S E : A : < E n t e r > ( E s p e c i f i e s th e n a m e o f t h e h a r d di s k

d r i v e t o w h i c h t he f lo p p y d i s k i s i n s er t e d, w h e r e d r i v e l e tt e r A i s
the destination.)

( D e p e n d i n g o n t h e t e r mi n a l ' s p r o m p t s e t t i n g , i t m a y b e d i f f e r e n t f r o m
the above.)

S i n c e y o u w i l l b e u sin g t h e m o d e l t o b e u se d p r i m a r i l y , e n t e r 0 o r
1.

- C o m p l e t i o n i s d on e i f d i s p l a y o f e x i t a pp e a r s .

T h i s w i l l b e c o v e re d i n P M T - 1 9 2 ( d i r e c to r y) o f d r i v e A .

• H o w t o t r a ns f e r W T ER M ( F o r e x a m p l e, p u t t h e a t t a c h e d f lo p p y di s k
i n d r i v e F a n d t r an s fe r i t t o h a r d d i s k d ri v e B . )

( I n t h e c a s e o f W IN D OW S , r e t u r n t o D O S )

- A : \ > F : < E n t e r > ( I t i s n o t n e c e s s ar y i f it i s a l re a d y i n d r i v e F . )

1 F: \>

- F : \ > W T I NS F : B : < En t e r > ( w h e r e F i s t h e d r i v e l e t t e r B c o n t a i ni n g

t h e f l o p p y d i s k , sp e c if y t h e n a m e o f t he h a rd d i s k d r i v e t o wh i c h y o u
want to transfer).
(In case of the display different from the above, it will be better depending
on the terminal prompt setting.)

Since you will be using the primary type first, type 0 or 1.

It will be completed if the display of 1 is displayed.

This will be covered in PMT-192 (directory) of drive B.

• Basic startup method of DXTERM (when there is DXTERM in the directory PMT-192
of hard disk drive A)

1 C: \> A: <Enter> (It is unnecessary if it is already in drive A.) A: \>

- A: \> CD PMT - 192 <Enter> (This is not necessary if it is already in PMT

- 192 directory.)

1 A: \ PMT - 192>

- A: \ PMT - 192> DXTERM <Enter>

This will launch DXTERM.

(Depending on the terminal's prompt setting, it may be different from the

above.)

• Basic start method of WTERM (when there is WTERM in the directory PMT-192
of hard disk drive B)
 -F: \ SB: <Enter> "(This is unnecessary if it is already in drive B.)

1 B: \>

1 B: \> CD PMT - 192 <Enter> (This is not necessary if it is already in PMT

- 192 directory.)

- B: \ PMT - 192>

1 B: \ PMT 492> WTERM <Enter>

- WTERM will now start up.

(Depending on the terminal's prompt setting, it may be different from the

above. :)

• P l e a s e u s e t h e d o c u me n t a t i o n i n c l u d e d w i t h e a c h s o f t w a r e fo r
u s a g e o f D X T E R M , WT E RM a n d v a r i o u s s e t ti n gs .

8 I n i t i a l i z a t i o n of PM T - 1 9 2

• Pressing the VOL - button on the front panel turns on the

p o w e r t o i n i t i a l i ze .

R S - 2 3 2 C ( b e t w e e n te r mi n a l a n d P M T - 1 9 2 )
Baud rate 12003 B
Bit length 8
Stop bit 1
No parity
F l o w c o n t r o l h a r d wa r e
 Wireless

F r e q u e n c y 4 3 1 . 0 0 MH z

9 R S - 2 3 2 C B a u d R a t e ( Co m m u n i c a t i o n S p e e d o f T N C a n d T e r m i n a l )
U s i n g C o m m u n i c a t i on s S o f t w a r e D X T E R M

• W i t h i n t h e P M T di r ec t o r y

- A > D X T E R M < E n t e r >( T he r e a r e t i m e s w h e n i t m a y be

d i f f e r e n t f r o m t h is de p e n d i n g o n t h e evening
p r e f e r e n c e o f a m in o r: A : ¥ P M T - 1 9 2 > etc.)

- D X T E R M s t a r t s u p.

P r e s s < F 4 > t o di s p l a y t h e s y s t e m e n vi r o n m en t m e n u . ( < F 4 > i s

function key.)

< U p > < D o w n > t o c h o o s e R S - 2 3 2 C P a r a m e t e r S e t t i n g a n d p r e ss

< E n t e r > ( o r p r e s s < R >) .

<Up><Down> to choose a baud rate at 1 mm and divine < Enter>

or Press <B>.)

< U p > < D o w n > t o s e l ec t 1 2 0 0 a n d p r e s s < E nt e r> ( O r < D > k e y )

C h o o s e l i n e i n i t i al i z at i o n w it h < Up > < Do w n > a n d < E nt e r > to

god. (Or press <J>. )

1 Press <Esc>.

1 I f c m d : i s d is p l a y ed a f t e r < E n te r > , i t me a ns t h a t P M T - 19 2

and the terminal were connected by 1200 B.

• A s a n e x a m pl e , w h e n c ha n g i n g t h e d e f au l t b a u d r a t e fr o m 1 2 00

B to 9600 B

-cmd: AB 9600 <Enter>

-ABAUD was 1200

1 T u r n o f f t h e p o w e r o f t h e c m d : R E S T A RT < En te r > o r t h e P MT

- 1 9 2 a n d t u r n i t o n ag a i n .

1 I n t h e a b ov e p r o c e d ur e , p re s s < F 4 > a n d s e t t h e R S - 2 32C

baud rate of the system environment menu to 9600 B.

1 c m d : E n t er A B < E n te r> a n d i t i s c om p l e t ed i f - A B A U D 96 0 0

is displayed.
10 Baud rate auto tracking setting (There are things that can not be done depending
on terminal model.)

TNC board (inside shield case)

Jumper1

Baudrate manual (Factory default) 1

- Baud rate automatic setting position 1

It is possible when there is 16 times the output of E-Mini's RS-232C

2 conversion

• You can change the position of the jumper on the PMT -

192 internal board.
• The baud rate of the PMT - 192 will automatically follow if you change
the RS - 232C baud rate of the above - mentioned system thinning.
• In this case, the baud rate display of PMT - 192 may differ from the
actual one.
• After turning on the power of the PMT - 192 after completing RS -
232C setting, it will be displayed as follows.

TONO Packet Radio PMT-192 AX.25 Level 2 Version 2.0 + BLP 1.0 Release
1.1.8a 02/23/96 - 32K RAM
Checksum $ 10
cmd:
(Release number, date, etc. are different from this display.)
11 Basic usage

♦ Time setting

The time setting is lost when PMT - 192 is powered off and
t h e r e s t a r t c o m m a n d is u s e d . S e t t h e t i m e ea c h t i m e . ( W h en
DXTERM is started, the time is automatically set.)

- cmd: DA <Enter> (Confirm fe.

-? clock not set (Time is not set.)

Perform the following operations.

1 P r e s s < F 3 > , s e l e c t t h e T N C t i m e s e t t i ng f r o m t h e T NC
operation menu and press <Enter>.

- cmd: DAYTIME 960305110740 (The time is set from the

terminal.)

- cmd: DA <Enter>

- 0 5 - 0 3 - 9 6 1 1 : 0 7 : 0 4 i s d i s p l a y e d a n d t h e t im e h a s b e e n s e t.
• R a d i o f r e q u e n c y s e t ti n g ( S e t a s 4 3 5 . 0 0 M H z a s a n e x a m p l e .)

-cmd: FREQ 3500 <Enter> (Enter the number excluding the

100 MHz range.)

1 FREQ was 3300 (previous setting value)

- cmd: FREQ <Enter>

It was set to 1 FREQ 3500 and set to 435.00 MHz.

• Communication speed (baud rate) setting with other

station (for example, set to 9600 B.)

There are 4 kinds of baud rate.

1200 B FSK
4800 B GMSK
9600 B GMSK
19200 B GMSK

-cmd: HB 9600 <Enter>

- HBAUD was 1200 (previous designation)

- cmd: HB <Enter>

- HBAUD 9600 is displayed and set to 960 BOB. (Set the same communication
speed as the other station.)

• Setting up the local callsign

Enter it as follows. (OOO is the local callsign.)

-cmd: MY 000000 <Enter>

-MYCALL was NOCALL
For confirmation, enter as follows.

- cmd: MY <Enter>
- MYCALL 000000 is displayed and the local callsign has been set.

• Connect with the remote station

Enter it as follows. (XXXXXX is the partner station call sign.)

-cmd: C XXXXXX <Enter>

If it is displayed as 1 *** CONNECTED to XXXXXX, it was able to connect with the

opposite station.

Characters entered from the terminal after this are sent to the remote station by
pressing <Enter>. Also, when a reply comes from the other station, it is displayed in
the dis- play.

• When connection could not be made

- *** retry count exceeded

- *** DISCONNECTED

If connect operation is specified and it is not connected even if it is performed for fe

times, this reconnection operation which is displayed is canceled. (Initial value
repeats connect operation 10 times.)

- *** XXXXXX busy.

- *** DISCONNECTED
If the remote station is connecting to another station or is set to reject connect,
this is displayed and the connection operation is canceled.
• Disconnect from the other station
First send a break or CTRL-C and set it to cmd: (command mode). (For
DXTERM, press <F10>.) Enter as follows.
- cmd: D <Enter>
If I *** DISCONNECTED is displayed, the connection with the other station has
expired.
• Use a digitor (use arbitrary stations as relay stations to communicate with
remote stations)
Enter it as follows. (XXXXXX is the counter station's counterpart, and ****** is
the relay station callsign.)
- cmd: C XXXXXX V ****** <Enter>
I *** CONNECTED to XXXXXX via ****** If it is displayed, it was able to
connect with the remote station via the relay station.
(Up to 8 stations can be entered by separating relay station call signs with a
comma and can be relayed in the order in which they are entered.)
1 cmd: C XXXXXX V ******, ****** ,,,,,, ****** <enter>
When disconnecting, please refer to the above (disconnect with the other
party).
• Use the repeater
In the command mode, make the following settings.
FREQ XXXX <Enter> (Levitator frequency to use)
TONE 3 <Enter> (when the tone frequency is 88.5 Hz)
OFFSET -500 <Enter> (place of off set frequency -5 MHz)
AXD 120 <Enter>
 You can now communicate by relaying the repeater.
For details of the command, please see the attached command list (contained in the
floppy disk).
If you are not using the repeater, make the following settings.

FREQ XXXX <Enter> (frequency to be used normally)

TONE 0 <Enter>
OFFSET 0 <Enter>
AXD 0 <Enter>
• Decompression of image data downloaded from RBBS etc. (after the compressed data)

The data of the image is generally shrunk by the pressure decompressing program LHA,
and further textualized by the text making program ISH is uploaded to the RBBS as an
image file.

It is converted to text by ISH and the fe file has the following character string
(header) at the beginning. (This header is an example.)

Make the data downloaded from the RBBS a file. (We will do it while the data received from the
RBBS is displayed on the screen.)

Include one or more headers and take them to the end. (It is taken from the header
of the header, but it recognizes the line after the header as an image.)
- A f t e r p r e s s i ng < R O L LD O W N > , m o v e t h e c u r s o r t o t h e b e g i nn i n g
o f t h e l i n e y o u w an t t o m a k e a f i l e w i th <U p > .

- I f yo u p r es s < F 6> , t h a t l i n e w i l l c h a n g e t o a n i n v e r t e d
character.

- I n v e r t c h a r a c te r s u nt i l t h e l a s t l in e y o u wa n t t o m a k e a f i l e
with <Dn>.

( U p t o t h e l i n e c on t ai n i n g t h e r o p e )

Y o u c a n a l s o u s e sy m bo l s o t h e r t h a n 0 3 あ . )

- P r e s s < F 8 > t o e nt e r a n a r b i t r a r y f i l e n am e .

- Y o u c a n c r e a t e a f il e i n t h e s a m e d i re c to r y .

T o p o s t t h i s f i l e w i th I S H

- P r e s s < F 2 > t o s el e ct c o m m a n d e x e c u t i on an d p r e s s < E n e r > .

- I S H O O O O . X X X < E nt e r> ( O O O O . X X X i s a da t a f i l e n a m e )
Y o u c a n c r e a t e a f i l e l a t e r i n I S H i n t h e - D X T E R M d i r e c t o r y.
( Y o u c a n u s u a l l y do OO O O . L Z H . )

T o u n p a c k t h i s f i le wi t h L H A

1 P r e s s < F 2 > t o s e le ct c o m m a n d e x e c u t i o n an d p r e s s < E n t e r > .

- L H A E O O O O . L Z H < En t er > ( O O O O . L Z H i s d at a f i l e n a m e )

- c a n d o 00 0 . M A G o r 00 0 . J P G e t c i n t h e s ame d i r e c t o r y . ( T h e
e x t e n s i o n . M A G . J P G e tc d i f f e r s d e p e nd i n g o n t h e t y p e o f t h e
surface image.)

P l e a s e p r e p a r e s e p a r at e l y i m a g e d i s p l a y s of t w a r e t o d i s p l ay
one image.

• K e y m a c r o s ( B y r e g is t e r i n g f r e q u e n t l y u se d c o m m a n d s e t c i n
t h e k e y m a cr o , i t c a n b e e x e c u t e d s i m p l y b y c a l l i n g t h e k e y
macro.)

K e y m a c r o r e g i s t r at i on e x a m p l e 1

F o r e x a m p l e , t o r eg i st e r F R E Q < E n t e r > in <F >

- P r e s s < F 7 > a n d s e l e ct R e g i s t e r M a c r o K e y fr o m t h e K e y M a c ro
menu and press. .

W h e n y o u s e e a l i st , p r e s s < F > .

E n t e r t h e c o m m a n d a nd p r e s s < E n t e r > . ( F or e x a m p l e , e n t e r
f r e q u e n c y d i s p l a y e t c. )

- P r e s s FR E Q < En t e r > .

- H o l d d ow n < C TR L > a nd p r e s s < \> t o en d k e y m a c r o

registration.
Execute the key macro (try executing the one
registered above)

- P r e s s < E S C > a n d w he n t h e l i st a p p ea r s , pr es s < F >

t o e x e c u t e . W he n y o u ex i t D X T E R M , t he k e y m ac r o s
disappear, but you can keep them with the next
operation.

- P r e ss < F4 > an d s e l e c t c h a n g e o f e x e c u ta b l e f il e f r om
system border menu and press <Enter>.

- I w i l l w r i t e t h e c urr e n t b o r de r t o D X T E R M.E X E

Cancel <ESC> Write <Y>?

When it is displayed, press <Y>.

Key macro registration example 2

F o r e x a m p l e , w h e n r e g i s t e r i n g re p e a t er

Frequency 439.88 MHz

Tone frequency 88.5 Hz

T r a n s m i s s i o n o f f s e t f r e q u e n c y -5 M H z

W e w i l l r e g i s t er a l l of t h e s e in t h e < \ > k e y "

- P r e s s < F 7 > t o r e g i s ter t h e m a c r o k e y f r o m t he k e y

macro menu

Select and press <Enter>.

- W h e n y ou s e e a l i s t, p r e s s < \> .

E n t e r t he c o mm a n d a n d p r e s s < En t e r > . ( F o r e xa m p l e ,
enter REPTSET etc.)

FREQ 3988 <Enter>

T O N E 3 < En t e r >

O F F S E T - 50 0 < E nt e r >

AXD 120 <Enter>

Continue to press.

- H o l d d ow n < C TR L > a nd p r e s s < \> t o en d k e yma p p

registration.
S i n c e t h e k e y ma c r o wh i c h s e e m s t o be c o n ve n i e n t i s c o n t a i n e d in t h e
f l o p p y d i s k i n a d va n ce , i t c a n l o a d a n d u se i t .

Load key macro

- Press <F7>, choose Load Macro Key from the Key Macro menu and press
<Enter>

- When the file name input screen appears, press <Enter>, enter the
drive name of the floppy disk, select KEYMCR 1 from the file び, and
press <Enter>.

- S i n c e t h e f i l e n a m e in p u t s c r e e n a p p e a r s a ga i n , p r e s s 0 ] t o c o m p le t e .

- P r e s s < F 4 > a ft e r t hi s a n d se l e c t th e c h an g e o f th e e x e cu t a b l e f i l e
f r o m t h e s y s t e m p o r t a l m e n u a n d p r e s s < E n t e r >, y o u ca n u s e i t w h e n e ve r
y o u s t a r t D X T E R M . ( I f y o u c h a n g e t h e e x e c ut a b l e f i l e o f t h e T e mp o
m e n u a f t e r l o a d i n g t h e k e y m a c r o , t h e k e y m a cr o s b e f o r e l o a d i n g w i ll
d i s a p p e a r , s o s a v e t he m b e f o r e h a n d i f ne c es s a r y . )

1 2 A f t e r s a l e s s e rv i ce

- • W e a t t a c h a w ar r an t y c a r d t o t h i s pr o du c t .

♦ P l e a s e c h e c k t h e d e al e r ' s s e a l a n d d a t e s ta m p j o n y o u r w a r r an t y c a r d
a n d a c c e p t i t f r o m t he d e a l e r a n d k e e p i t ca r e f u l l y a n d k e e p i t i n
a safe place.

2 • T h e w a r r a n t y pe r io d i s o n e y e a r f r om th e d a t e o f p u r c h a se .

• I n n o rm a l u s e , w i t h in t h i s pe r i o d , s h o u l d w e f a i l d u e t o i n a d e q ua c i e s
i n m a n u f a c t u r i n g , w e w i l l r e p a i r i t f r ee of c h a r g e b a s e d o n t h e
w a r r a n t y r e g u l a t i on s a t o u r c o m p a n y " .

3 • R e p a i r a f t e r th e w a r r a n t y p e r i o d h as el a p s e d
 • I f r e p a i r i s a b le to m a i n t a i n p e r f o r ma n ce , w e w i l l t e a c h yo u
" e x t e n s i v e r e p a i r " a cc o r d i n g t o c u s t o m er ' s r e q u e s t .

4 . I f y o u h a v e an y q u e st i o n s a b o u t a f t e r - s a l es s e r v i c e , p l e a s e c on ta c t
y o u r d e a l e r o r o u r c om p a n y .

13 specification

Frequency range 430.000 to 439.990 MHz (10 kHz step)

Modulation type F1 (GMSK) F 2 (FSK) F 3
c o m m u n i c a t i o n s p e ed 1200, 4800, 9600, 19200 baud
RS-232C connector D-SUB 25 pin specification
transmit power 20 W / 1 W (PMT - 192 H) 10 W / 1 W (PMT - 192 L)
T r a n s m i t t e r c o n n e ct o r N type specification 50Ohm
u n n e c e s s a r y r a d i a ti o n - 60 dB or more Sat
maximum deviation 5 kHz (F 3)
d e v i a t i o n v a r i a t i on me t h o d Reactance change Double super heterodyne
first IF 45 MHz
second IF 455 kHz
r e c e p t i o n s e n si t i v i t y ( 1 2 d B -10 dBmicroV / -16 dBmicroV (JAIA measurement
SINAD) method)
S / N a t i n p u t 0 . 5 m ic r o V 30 dB or more
A F o u t p u t ( a t 1 0 % d i s t o r t i o n 200 mW
• load)
E x t e r n a l s p e a k e r ja c k 03.5 mini jack specification 8 Ohm
E x t e r n a l M i g C o n n ec t or DIN 8 pin specification 600 Ohm
P o w e r - s u p p l y v o l t ag e DC 13.8 V (maximum)
C u r r e n t c o n s u m p t i on PMT-192H / 4.5 A (maximum) PMT-192L /
S p e c i f i c a t i o n s o f th i s m a c h i n e •2.5
R aA
ti(maximum)
n g • A p pe a r a n c e e t c . a r e s u b j ec t t o ch a n g e
w i t h o u t n o t i c e f o r i mp r o v e m e n t .
Body dimensions 148 mm (W) x 44 mm (H) x 208 mm (D) (excluding
This weight
protrusions)
1.5 kg