960326 PARTS LIST
BLACKMER PARTS LIST Page 1 of 2 201-B00
With Installation and Maintenance Instructions Section 201
T-TYPE TRUCK PUMP STRAINERS Effective Aug 2015
FOR PUMP SIZES: 2″, 2.5″, 3″ Replaces Jun 2015
Part No. Part No Part No
Ref. No. Description Qty.
2" Size 2.5" Size 3" Size
1 Strainer Assembly with Ref. 2, 42C, 44C (4), & 43 (1) 1 740053 740056 740061
2 Strainer Basket 1 621608 621612 621801
2
Body Flange – NPT 651411 651611 651803
42 2 0-1
Weld 2 — — 655102
Inlet Flange – NPT 651603 651611 651803
42A 1
Weld — — 655102
42C Strainer Cover 1 * * *
43 Gasket - Inlet Flange, Strainer Cover 2 381650 381650 381816
43A 1, 2 Gasket - Body Flange 1 381421 381650 381816
44 1 Capscrew - Strainer Body 0-4 920331 920491 920491
Capscrew - 2" NPT Inlet Flange 920491 920491 —
44A Capscrew – 2 1/2" NPT Inlet Flange 4 — 920532 —
Capscrew - 3" NPT Inlet Flange 920532
— —
3” Weld Inlet Flange 920510
44C Capscrew - Strainer Cover 4 920491 920491 920491
2 Mounting Bolt – NPT Body Flange 920381 920547 920547
44D 0-4
Weld Body Flange — — 920539
2
44E Nut - Mounting Bolt 0-4 922841 922850 922850
1 2
For direct pump mounting use Ref. Nos. 43A and 44. For intake line mounting use Ref. Nos. 42, 43A, 44D and 44E.
* Only available with Strainer Assembly (Ref. 1).
Fig. 1
Pump Mounted
Fig. 2
Inline Mounting
INSTALLATION
NOTICE: STRAINER MOUNTING
Blackmer truck pumps MUST only be installed in systems Blackmer T-Type strainers are designed for direct mounting on
which have been designed by qualified engineering Blackmer truck pumps, or as line strainers for use with
personnel. The system MUST conform to all applicable Blackmer truck pumps or other makes of pumps. T-Type
local and national regulations and safety standards. strainers are available in 2, 2.5 and 3-inch sizes.
These instructions are intended to assist in the For direct mounting on Blackmer 2, 2.5 and 3-inch truck pump
installation of Blackmer T-Type strainers, and MUST be models, the strainer takes the place of the intake pipe flange
kept with the pump. and bolts directly to the INTAKE port of the pump. To mount
the strainer directly on the Blackmer pump, use four (4)
Blackmer truck pump service shall be performed by strainer capscrews (Ref. No. 44) and flange gasket (Ref. No.
qualified technicians ONLY. Service shall conform to all 43A). See Figure 1.
applicable local and national regulations and safety
standards. When using the Blackmer T-Type strainer as a line strainer, 2,
21/2 and 3-inch NPT tapped pipe flanges are available to
Thoroughly review the pump manual, all instructions and adapt the strainer for use in the intake line. To mount the
hazard warnings, BEFORE performing any work on strainer in the intake line, use the strainer body flange (Ref.
Blackmer truck pumps. No. 42), flange gasket (Ref. No. 43A), and four (4) mounting
Maintain ALL system and Blackmer truck pump operation bolts and nuts (44D & 44E). See Figure 2.
and hazard warning decals.
Failure to set the vehicle emergency Failure to relieve system pressure prior to
brake and chock wheels before performing pump service or maintenance
performing service can cause severe can cause personal injury or property
personal injury or property damage. damage.
Dimensions – in. (mm)
Strainer
C D E F G H J K L Q
Size
2 1 3/4 3 13/16 4 3/4 4 2 7/8 3 5/8 2 5/8 2 1/4 6 3/8
(25.4) (19) (72.6) (121) (102) (73) (92) (66.7) (57.2) (162)
2.5 1 1/4 1 1/4 3 13/16 4 3/4 4 2 7/8 4 2 7/8 3 1/16 6 1/2
(31.8) (31.8) (72.6) (121) (102) (73) (102) (73) (77.8) (165)
3 1 3/16 1 3/16 4 5 4 3/4 3 1/2 4 3/4 3 1/2 3 7
(30.2) (30.2) (102) (127) (121) (88.9) (121) (88.9) (76.2) (178)
NOTICE: Blackmer manuals and parts lists may be obtained by contacting
Blackmer customer service or via the Blackmer website (www.blackmer.com).
1809 Century Avenue, Grand Rapids, Michigan 49503-1530, U.S.A.
Telephone: (616) 241-1611 / Fax: (616) 241-3752 Parts List 201-B00
E-Mail: blackmer@blackmer.com / Internet: www.blackmer.com Page 2 of 2
