DKG-116 User Manual V-03 (30.03.
2011)
DKG-116 MANUAL AND
REMOTE START UNIT
DESCRIPTION MEASUREMENTS
The DKG-116 is a low cost Generator Volts: L1-N, L2-N, L3-N
gasoline/diesel genset control unit Generator Volts: L1-L2, L2-L3, L3-L1
designed to start and stop a genset both Generator Frequency
manually and remotely. Battery Voltage
The manual control is made using RUN
and STOP pushbuttons on the front
OPTIONS
panel. The remote control is made via
Auxiliary output (negative pulling).
REMOTE START input signal.
Magnetic pickup input.
When RUN button is pressed or a Remote
Start signal arrives, the engine will be FEATURES
cranked up to 3 times. When it runs, the
crank relay will be immediately deactivated Both Manual and remote control
and after Holdoff timer delay, fault Generator protection
checking will be enabled. When the engine
is running, if a fault condition is detected Built in alarms and warnings
then the engine is shutdown immediately Remote Start operation available
and the unit indicates the source of the True RMS measurements
failure through related alarm led.
Tamper-proof engine hours display
If the Remote Start signal disappears or Field adjustable parameters
the STOP button is pressed or the genset
will immediately stop. High current Fuel and Crank outputs
Optional auxiliary output
The MENU button selects display
parameter scroll and allows program Optional magnetic pickup input
mode entry and lamp test functions. Digital inputs: 4
The total engine run hours is kept in a Survives cranking dropouts
tamper-proof non-erasable memory which Sealed front panel
is not affected by power failures.
Standard panel dimensions: 96x48mm
Plug-in connection system
DKG-116 User Manual V-03 (30.03.2011)
PRECAUTIONS FOR INSTALLATION AND SAFE USE
Failure to follow below instructions will result in death or
serious injury.
Circuit breakers must be connected serially to BAT+, PHASE-L1, PHASE-L2 and PHASE-
L3 terminals, in close proximity of the unit.
Fuses must be of fast type with a maximum rating of 6A.
Disconnect all power before working on equipment .
When the genset is running, do not touch terminals.
Do not try to clean the device with solvent or the like. Only clean with a dump cloth.
Verify correct terminal connections when wiring.
Electrical equipment should be serviced only by competent service personnel. No
responsibility is assured by the manufacturer or any of its subsidiaries for any
consequences arising out of the use of this material.
Only for front panel mounting.
CONNECTION DIAGRAM
DKG-116 User Manual V-03 (30.03.2011)
PROGRAMMING
Both ‘High Temperature’ and ‘Emergency Stop’ inputs must be connected
to ‘Battery negative’ prior to enter the programming mode.
The unit offers 12 programmable parameters listed below.
FACTORY
NO SYMBOL RANGE DESCRIPTION
SET
1 70-500 V 170 V Low AC voltage shutdown limit
2 70-500 V 300V High AC voltage shutdown limit
3 0-1000 50 MPU crank cut frequency divided by 4
4 0-1 0 Nominal frequency: 0=50Hz 1=60Hz
5 0-1 0 Oil input: 0=pressure switch 1=level switch
6 0-1 0 Fuel output type 0:Fuel 1:Stop
0-3 0 Relay 3 function
7
0:Alarm 1:Choke 2:Stop 3:Preheat
8 0-15 sec 0 Choke timer in seconds
9 0-15 sec 10 Preheat timer in seconds
0-7 0 Connection topology:
0=1phase 1=2phases 2=3 phases 3=3 phases ,
center tapped delta (voltage checks on first 2
10
phases only)
4..7= same as 0..3, but voltages are not
displayed
11 0-15 sec 5 Under/over voltage delay timer
12 - - Phase L1-N calibration value
13 - - Phase L2-N calibration value
14 - - Phase L3-N calibration value
The program mode is entered by long-pressing the MENU button. Each depression of the MENU
button will switch to the next parameter.
Another long press will enable the lamp test mode. Then any depression of MENU button will return
the display to normal mode.
If no key is pressed, then the unit will return to normal display mode with a delay.
1- When genset is in off mode; press MENU button for 5 sec to
MENU
enter program mode and display the Low AC Voltage limit.
2- Press RUN or STOP buttons until requested value is displayed.
RUN STOP
N 3- Press MENU button for saving the Low AC Voltage limit and
MENU displaying the next program parameter.
4- Press RUN or STOP buttons until requested value is displayed.
RUN STOP
N
5- Press MENU button for saving the parameter and displaying
MENU the next parameter.
6- Repeat steps 4 and 5 as required.
7- Any time on settings, press MENU button for 3 sec. to exit from
RUN STOP
program mode.
N
DKG-116 User Manual V-03 (30.03.2011)
TECHNICAL SPECIFICATIONS DIESEL ENGINE SELECTION
Alternator voltage: 15 to 300 V-AC (Ph-N)
Alternator frequency: 50 or 60 Hz nominal. In order to control
Measurement Accuracy: 0.5% + 1 digit
diesel engines,
connect a conductive
Overspeed: nominal frequency + 14%
wire to between
(+24% overshoot)
terminals 1 and 3.
Underspeed: 30 Hz
Crank time: 10 sec.
Crank rest: 10 sec.
Crank attempts: 3 PANEL CUTOUT DIMENSIONS
Stop timer: 10 sec.
Holdoff timer: 10 sec.
44mm
DC Supply Range: 9.0 to 16.0 V-DC
Cranking dropouts: survives 0 V for 100ms.
Typical Standby Current: 12mA-DC (display off)
Maximum Operating Current: 130 mA-DC
Fuel and Crank outputs: 10A @ 12V-DC
Auxiliary Output: 1A @ 12V-DC (negative pulling
protected semiconductor output)
92mm
Magnetic pickup Input: 1.5 to 30Vpp
Operating temp.: -40°C (-40°F) to 80 °C (176°F).
Maximum humidity: 95% non-condensing. PACKAGING INFORMATION
Dimensions: 102 x 55 x 40 mm (WxHxD)
Pieces per Package: 24
Packed weight: 140 g
Package Size: 280 x 170 x 215mm (LxWxH)
Case Material: High Temp. ABS/PC (UL94-V0)
Package Weight: 3.6 kg
IP Protection: IP65 (front panel), IP30 (rear)
Conformity (EU directives)
-2006/95/EC (low voltage)
-2004/108/EC (EMC)
Norms of reference:
EN 61010 (safety requirements)
EN 61326 (EMC requirements)
DATAKOM Electronics Ltd.
Tel: +90-216-466 84 60 Fax: +90-216-364 65 65 e-mail: datakom@datakom.com.tr http: www.datakom.com.tr
