TCE.

M4-106-05 TCE CONSULTING ENGINEERS LIMITED SECTION : D

ISSUE NO. R2
ENQ.SPEC.NO. DATA SHEET A
TCE. LARGE AXIAL FANS SHEET : 1 OF 3

1. DESIGNATION : 22.3 PERMISSIBLE PRESSURE DROP :

DESIGN DATA
(CONTINUED)
Kg/cm 2
2. NUMBER REQUIRED : ( W+ 22.4 QUALITY : AS PER
S)
3. TAG NUMBERS :
4. TYPE : TUBE AXIAL / VANE AXIAL
5. LOCATION : INDOOR / OUTDOOR 23. MOUNTING : ON CONCRETE
GENERAL

6. OPERATION : CONTINUOUS/ FOUNDATION

INTERMITTENT 24. MODE OF ADJUSTMENT OF GAS FLOW
Hrs/Day
7. LOCATION IN HAZARDOUS AREA : CONTROL: INLET GUIDE VANE /
YES / NO INLET VANE AND HYDRAULIC SPEED
8. HAZARDOUS AREA CLASSIFICATION: VARIABLE / DAMPER /VARIABLE
AS PER IS 5572 ZONE 0 / 1 / 2 PITCH CONTROL
9. ARRANGEMENT: AMCA STANDARD 25. TYPES OF BLADES:
ARRANGEMENT NO. (NOTE-1)
10. CAPACITY (FAD) : M³/ 26. CASING: AXIAL/RADIALLY SPLIT
Hr
10.1 NORMAL :
CONSTRUCTION FEATURES

10.2 MAXIMUM: 27. VOLUTE : DIFFUSER/

11. GAS HANDLED: MANUFACTURER’S STANDARD
12. TEMPERATURE OF GAS :
°C
13. DENSITY OF GAS: 28. SHAFT : COUPLED / VERTICAL /
Kg/M3
14. SUCTION HUMIDITY : MAXIMUM MANUFACTURER’S STANDARD
(RH%) :
MINIMUM
DESIGN DATA

15. STATIC PRESSURE : 29. COUPLING: FLEXIBLE

mmWC
16. VELOCITY PRESSURE : 30. MAIN BEARING : ROLLER BEARING
mmWC
17. TOTAL PRESSURE : FOR RADIAL AND THRUST BEARING
mmWC
18. DESIGN AMBIENT TEMPERATURE :
31. SEAL: BETWEEN NON ROTATING
°C
19. LUBRICATION : FORCED/BATH REGULATING LINKAGE AND
20. DESIGN MARGIN ON HYDRAULIC CYLINDER
20.1 CAPACITY: 32. BLADE THRUST BEARING:
%
20.2 TOTAL PRESSURE :
%
21. MAXIMUM SPEED : 33. BLADE ANGLE VARIATION:
RPM
21.1 FOR DUST LADEN GAS HYDRAULIC SYSTEM
900
21.2 FOR CLEAN AIR
1200
22. BEARING COOLING WATER 34. BLADES WITH RENEWABLE WEAR
22.1 INLET PRESSURE : Kg/cm 2(g) RING NOSES:
22.2 TEMPERATURE: IN/OUT / 35.
0
C
 REV.NO. PPD. BY : JOB NO. CLIENT:
DATE CHD. BY : TCE.
REV. BY DATE : PROJCET :
FILE NAME: DA10605R2.DOC TCE FORM NO. 330 R1
 TCE.M4-106-05 TCE CONSULTING ENGINEERS LIMITED SECTION : D
ISSUE NO. R2
ENQ.SPEC.NO. DATA SHEET A
TCE. LARGE AXIAL FANS SHEET : 2 OF 3

36. BAFFLE OR SPLITTER PLATE: 59. COUPLING GUARD : YES

FEATURES(CONTD.)

60. COMMON BASE FRAME : YES

CONSTRUCTION

37. THERMO COUPLES AND BEARING 61. FOUNDATION BOLTS: YES/NO

TEMPERATURE MEASUREMENT: 62. FORCED LUBRICATION UNIT WITH
38. SPARK RESISTANT CONSTRUCTION PUMPS, COOLERS, FILTERS, OIL

ACCESSORIES
TYPE AS PER AMCA : A/ B/ LEVEL INDICATOR, CONNECTED
C
39. CASING: PIPING ETC: YES /
NO
63. LOCAL INSTRUMENTS: YES / NO
40. IMPELLER BLADE : 64. START-UP AND ESSENTIAL SPARES
FOR 2YEARS NORMAL OPERATION:
41. INLET CONE: YES / NO
42. OUTLET DIFFUSER: 65. HYDRAULIC CONTROL UNIT
WTH PUMPS, FILTERS, COOLERS,
MATERIALS OF CONSTRUCTION

43. IMPELLER HUB: ASTM A445 CONNECTED PIPING ETC.: YES / NO

66. REFER TCE.M4-907
44. SHAFT: 67. ESSENTIAL SPARES
45. MAIN BEARINGS: 67.1
SPARES AND MAINTENANCE

67.2
TOOLS AND TACKLES

46. BEARING HOUSING: 67.3

67.4
47. BLADE THRUST BEARING : 67.5

48. SHAFT SLEEVE: 67.7
49. COUPLING: 67.8
50. BLADE SHAFT PENETRATION SEAL: 67.9
67.10
51. FOUNDATION BOLTS: 68. AS PER TCE.M4-904 OR TCE.M4-185-01
52. AND TCE.M4-185-10, 39 OR
TESTS AND INSPECTION

53. TCE.M4-186-08(NOTE-2)
54. MOTOR : BY VENDOR / PURCHASER 69. PERFORMANCE TEST AT SITE
AS PER TCE. M4-203-01/02 REQUIRED :
ELECTRICAL

YES/NO
55. STARTER : BY VENDOR /PURCHASER 70.
56. 71.
57. 72.
58. 73.
REV.NO. PPD. BY : JOB NO. CLIENT:
DATE CHD. BY : TCE.
REV. BY DATE : PROJECT:
ISSUE NO. R2

FILE NAME: DA10605R2.DOC TCE FORM NO. 330 R1

TCE.M4-106-05 TCE CONSULTING ENGINEERS LIMITED SECTION : D
ENQ.SPEC.NO. DATA SHEET A
TCE. LARGE AXIAL FANS SHEET : 3 OF 3

74. PRIMER : EPOXY / RED OXIDE 79. CAPACITY (FAD) :

PERFORMANCE GUARANTEES
74.1 NUMBER OF COATS : (+) (-)
M3/Hr
74.2 DRY FILM THICKNESS PER COAT: 80. TOTAL PRESSURE :
 (+) (-)
PAINTING

mmWC
75. FINISH PAINT : EPOXY / SYNTHETIC 81. POWER CONSUMPTION :
ENAMEL (+) (-) KW
75.1 NUMBER OF COATS : 82.
75.2 DRY FILM THICKNESS PER COAT: 83.
 84.
76. FOR DESIGN, TESTING AND 85. POWER CONSUMPTION
INSPECTION : IS 3588 / BS 848 / Rs.

COST LOADING
AND PENALTY
STANDARDS

/KW
CODES AND

AMCA 203 / AMCA 210 / AMCA 303 / 86.

AMCA 311 / AMCA 410 87.
77. 88.
78. 89.
NOTES
1. REFER AMCA STANDARD 99-2404-78 IN AMCA STANDARDS HANDBOOK.
2. FOLLOWING ADDITIONAL TESTS INDICATED AS ‘B’ IN TCE.M4-186-08 SHALL ALSO BE
CARRIED OUT, WHEN TCE.M4-186-08 IS APPLICABLE.

REV.NO. PPD. BY : JOB NO. CLIENT:

DATE CHD. BY : TCE.
REV. BY DATE : PROJECT:
FILE NAME: DA10605R2.DOC TCE FORM NO. 330 R1