Scribd
Upload
117 views3 pages

Get The Needed Length of The Cable and Add A Little Extra Wire, Just in Case

The document provides instructions for terminating an Ethernet cable by inserting the wires into an RJ-45 plug. It involves: 1. Cutting the cable to length and stripping the outer jacket. 2. Checking for cuts on the wires and redoing if cuts are found. 3. Untwisting and cutting the wire pairs to length. 4. Arranging the wires according to the 568B standard and inserting them fully into the plug before crimping. 5. Crimping the plug with a crimping tool and double checking the wiring before use.

Uploaded by

JohnLesterMaglonzo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
117 views3 pages

Get The Needed Length of The Cable and Add A Little Extra Wire, Just in Case

The document provides instructions for terminating an Ethernet cable by inserting the wires into an RJ-45 plug. It involves: 1. Cutting the cable to length and stripping the outer jacket. 2. Checking for cuts on the wires and redoing if cuts are found. 3. Untwisting and cutting the wire pairs to length. 4. Arranging the wires according to the 568B standard and inserting them fully into the plug before crimping. 5. Crimping the plug with a crimping tool and double checking the wiring before use.

Uploaded by

JohnLesterMaglonzo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

3.

CHECK THE WIRES FOR AY CUTS THAT


1. GET THE NEEDED LENGTH CAN EXPOSE THE COPPER WIRE INSIDE.
OF THE CABLE AND ADD A IF IT HAS ANY, YOU NEED TO CUT THE
ENTIRE WIRES OFF AND START OVER AT
LITTLE EXTRA WIRE, JUST STEP ONE. BECAUSE EXPOSED COPPER
IN CASE. WIRE WILL LEAD TO POOR
PERFORMANCE OF CONNECTIVITY

4. UNTWIST THE PAIRS AND LAY IT


2. CAREFULLY REMOVE THE OUTER FLAT. THE WHITE PIECE OF THREAD
JACKET OF THE CABLE. MAKE SURE NOT CAN BE CUT OFF EVEN WITH THE
TO CUT THE WIRES INSIDE. ONE GOOD
JACKET AND DISPOSED. FOR EASIER
WAY TO DO THIS TO CUT LEGTHWISE
HANDLING, CUT THE WIRES SO THEY
WITH SNIPS OR A KNIFE ALONG THE SIDE
OF THE CABLE, AWAY FROM YOURSELF ARE ¾ “ (19mm) LONG FROM THE
ABOUT AN INCH TOWARD THE OPEN END. BASE OF JACKET AND EVEN IN
LENGTH.
5. ARRANGE THE WIRES BASED ON WIRING
7. KEEP THE WIRES FLAT AND IN ORDER
SPECIFICATIONS YOU ARE FOLLOWING.
AS YOU PUSH THEM INTO THE RJ-45 PLUG
568B STRAIGHT THROUGH CONNECTION WITH THE FLAT SURFACE OF THE PLUG ON
WIRE CODING. TOP. YOU CAN TELL IF ALL THE WIRES
 WHITE ORANGE INTO THE JACKIF THE WIRE IS LOCATED IN
 ORANGE EACH HOLE. YOU MAY HAVE TO USE A
 WHITE GREEN LITTLE EFFORT TO PUSH THE PAIRS
 BLUE FIRMLY INTO THE PLUG. VERIFY THAT THE
 WHITE BLUE SEQUENCE IS STILL CORRECTLY BEFORE
 GREEN CRIMPING.

6. PRESS ALL THE WIRES FLAT AND


8. PLACE THE WIRED PLUG INTO THE
PARALLEL, BETWEEN YOUR THUMB
CRIMPING TOOL, GIVE THE HANDLE A
AND FOREFINGER. CUT THE TOP OF
FIRM SQUEEZE. ONCE YOU HAVE
THE WIRES EVEN ONE ANOTHER SO
COMPLETED THE CRIMP, THE HNDLE
THAT THEY ARE ½ “ LONG FROM THE
WILL RESET TO THE OPEN POSITION.
BASE OF THE JACKET LEAVING A ½ “
TO ENSURE ALL PINS ARE SET, SOME
OF ROOM FOR THE INDIVIDUAL
PREFER TO DOUBLE CRIMP BY
CABLES. ENSURE THAT THE CUT WIRES
REPEATING THIS STEP.
ARE EVEN AND CLEAN.
9. TEST THE CABLE TO ENSURE THAT
IT WILL FUNCTION IS THE FIELD.
MISWIRED CONNECTION COULD LEAD
TO PHYSICAL DAMAGE OF
COMPUTERS OR PHONE SYSTEM
EQUIPMENT. A SIMPLE CABLE TESTER
CAN QUICKLY VERIFY THAT
INFORMATION FOR YOU.

You might also like