BISHOP

O0001
N5 G97 G95 S500 F.1 M3 ; (SPINDLE SPEED=500 FEED RATE=0.1 )
N10 T0101 ; (FINISHING TOOL SDJC R 1616)
N15 G0 X35 Z1 ; (TOOL POSITIONED TO X35 Z1)
N20 G73 U1 R1 ; (CONTOUR TURNING)
N25 G73 P30 Q95 U0 W0 ; (CONTOUR TURNING FROM N30 TO N95)
N30 G0 X0 Z0 ; (TOOL POSITIONED TO X0 Z0)
N35 G3 X3 Z-6.66 R3.5 ; (CIRCULAR INTERPOLATION CLOCKWISE)
N40 G1 X12 Z-11.29 (TOOL POSITIONED TO X12 Z-11.29)
N45 G3 X12 Z24.17 R9 ; (CIRC. INTERP. CW TO X12 Z24.17 W/ R9)
N50 Z-27.71 R1.5 (CIRC. INTERP. CW TO Z-27.71 W/ R1.5)
N55 G1 X27.23 Z-31.13 (LIN. INTERP. TO X27.23 Z-31.13)
N60 G3 X26 Z-34 R1.5 ; (CIRC. INTERP. CW TO X26 Z-34 W/ R1.5)
N65 G0 X22 Z-63 ; (TOOL POSITIONED TO X22 Z-63)
N70 G2 X22 Z-67 R3 ; (CIRC. INTERP. CCW TO X22 Z-67 W/ R3)
N75 G1 X27.95 Z-69.09 ; (LIN. INTERP. TO X27.95 Z-69.09 )
N80 G3 X30 Z-78 R6 ; (CIRC. INTERP. CW TO X30 Z-78 W/ 6)
N85 G1 Z-83 ; (LIN. INTERP. TO Z-83)
N90 X28 Z-84 ; (LIN. INTERP. TO Z-84 CHAMFER)
N95 G0 X35 ; (TOOL POSITIONED TO X35)
N100 T0303 ; (FINISHING TOOL SVJC L 1616)
N105 G0 X30 Z-63 ; (TOOL POSITIONED TO X30 Z-63)
N110 G75 U22 W-63 R3 ; (PATTERN REPEATING FROM X22 Z-63 W/ 3 REPETITIONS)
N115 G75 P125 Q140 U0 W0 ; (PATTERN REPEATING FROM N125 TO N140)
N120 G0 X22 Z-63 ; (TOOL POSITIONED TO X22 Z-63)
N125 G3 X16.03 Z-58.92 R6 ; (CIRC. INTERP. CW TO X16.03 Z-58.92 W/ R6)
N130 G1 X12 Z-33 ; (LIN. INTERP. TO X12 Z-33)
N135 X30 ; (LIN. INTERP. TO X30)
N140 M30 ; (END PROGRAM)
ROOK
O0001
N5 G96 S1000 F.1 M3 ; (CONSTANT CUTTING SPEED=1000 FEED RATE=0.1)
N10 T0202 ; (FINISHING TOOL SVJC L 1616)
N15 G0 X50 Z-63 ; (TOOL POSITIONED TO X50 Z-63)
N20 G75 U5 Z-63 R10 ; (PATTERN REPEATING )
N25 G75 P30 Q90 U.1 R.1 ; (PATTERN REPEATING FROM N30 TO N90)
N30 G0 X40 Z-63 ; (TOOL POSITIONED TO X40 Z-63)
N35 G1 X36 ; (LIN. INTERP. X36)
N40 X37 Z-62 ; (LIN. INTERP. X37 Z-62)
N45 Z-57 ; (LIN. INTERP. Z-57)
N50 G2 X34.39 Z-50.2 R5 ; (CIRC. INTERP. CCW X34.39 Z-50)
N55 G1 X27 Z-47 ; (LIN. INTERP. X27 Z-47)
N60 G2 X27 Z-45 R1 ; (CIRC. INTERP. X27 Z-45 W/ R1 FILLET)
N65 G1 X22 Z-18 ; (LIN. INTERP. X22 Z-18)
N70 G2 X26 Z-16 R2 ; (CIRC. INTERP. CCW X26 Z-16 W/ R2 FILLET)
N75 G1 Z-13 ; (LIN. INTERP. Z-13)
N80 X29 ; (LIN. INTERP. X29)
N85 G2 X30 Z-12 R1 ; (CIRC. INTERP. X30 Z-12 W/ R1)
N90 G1 Z0 ; (LIN. INTERP. Z0)
N95 G0 X80 ; (TOOL POSITIONED TO X80)
N100 G72 P30 Q95 ; (FINISHING CYCLE FROM N30 TO N95 )
N105 G96 S1000 F.1 M3 ; (CONSTANT CUTTING SPEED=1000 FEED RATE=0.1)
N110 T0101 ; (FINISHING TOOL SDJC R 1616)
N115 G0 X30 Z2 ; (TOOL POSITIONED TO X30 Z2)
N120 G1 X30 Z-1 ; (LIN. INTERP. X30 Z-1)
N125 G0 X29 Z0 ; (TOOL POSITIONED TO X29 Z0)
N130 G3 X30 Z-1 R1 ; (CIRC. INTERP. CW X30 Z-1 W/ R1)
N135 G97 G95 S1000 F.1 M3 ; (SPINDLE SPEED=1000 FEED RATE=0.1)
N140 T0303 ; (START DRILL 90°/12MM)
N145 G0 X0 Z2 ; (TOOL POSITIONED TO X0 Z2)
N150 G1 Z-3 ; (LIN. INTERP. Z-3)
N155 G0 Z5 ; (TOOL POSITIONED TO Z5)
N160 G96 S500 F.1 M3 ; (CONSTANT CUTTING SPEED=500)
N165 T0404 ; (TWIST DRILL 8MM)
N170 G0 X0 Z1 ; (TOOL POSITIONED TO X0 Z1)
N175 G99 G83 Z-7 R10 Q5000 P1000 ; (RETURN TO INITIAL PLANE)
N180 G0 Z15 ; (TOOL POSITIONED TO Z15)
N185 M30 ; (END PROGRAM)
PAWN
O0001
N5 G97 G95 S500 F.1 M3 ; (SPINDLE SPEED=500 FEED RATE=0.1)
N10 T0101 ; (FINISHING TOOL SDJC R 1616)
N15 G0 X35 Z1 ; (TOOL POSITIONED TO X35 Z1)
N20 G73 U1 R1 ; (CONTOUR TURNING)
N25 G73 P30 Q80 U0 W0 ; (CONTOUR TURNING FROM N30 TO N80)
N30 G0 X0 Z0 ; (TOOL POSITIONED TO X0 Z0)
N35 G3 X7 Z-15.19 R8 ; (CIRC. INTERP. CW X7 Z-15.19 W/ R8)
N40 G1 X19.1 Z-19.16 ; (LIN. INTERP. X19.1 Z-19.16)
N45 G3 X19.1 Z-21 R1 ; (CIRC. INTERP. X19.1 Z-21 W/ R1)
N50 G0 X20.9 Z-44.11 ; (TOOL POSITIONED TO X20.9 Z-44.11)
N55 G3 X20 Z-46 R1 ; (CIRC. INTERP. X20 Z-46 W/ R1)
N60 G1 X28 Z-49 ; (LIN. INTERP. X28 Z-49)
N65 G3 X30 Z-56 R5 ; (CIRC. INTERP. CW X30 Z-56 W/ R5)
N70 G1 Z-61 ; (LIN. INTERP. Z-61)
N75 X29 Z-62 ; (LIN. INTERP. X29 Z-62)
N80 G0 X35 ; (TOOL POSITIONED TO X35)
N85 T0303 ; (FINISHING TOOL SVJC L 1616)
N90 G0 X30 Z-44.11 ; (TOOL POSITIONED TO X30 Z-44.11)
N95 G75 U20.9 W-44.11 R3 ; (PATTERN REPEATING)
N100 G75 P110 Q125 U0 W0 ; (PATTERN REPEATING FROM N110 TO N125)
N105 G0 X20.9 Z-44.11 ; (TOOL POSITIONED TO X20.9 Z-44.11)
N110 G3 X14.64Z-39.83 R6 ; (CIR. INTERP. CW X14.64 Z-39.83 W/ R6)
N115 G1 X8 Z-20 ; (LIN. INTERP. X8 Z-20)
N120 X19.1 ; (LIN. INTERP. X19.1)
N125 M30 ; (END PROGRAM)
QUEEN
O0001
N5 M06 T0707; (TOOL NO.7 ND OFFSET NO.7)
N10 G9 M04 S800 ; (SPINDLE DIRECTION COUNTER CLOCKWISE)
N15 M08;
N20 G00 X25.0 Z5.0;
N25 G01 Z-0.5 ; (FACING OF 1 MM)
N30 G01 X0.0 F0.1; (FEED RATE OF 0.1 MM)
N35 G00 X25.0 Z5.0;
N40 G01 Z-0.5 F0.1;
N45 G01 0.0 F0.1;
N50 G00 X25.0 Z5.0;
N55 G01 Z-1.0; X0.0;
N60 G00 X25.0 Z5.0;
N65 G71 U1.0 R2.0; (MULTIPLE TURNING CYCLE FOR ROUGH TURNING)
N70 G71 P05 Q11 U0.5 W0.5 F0.2 S800 ;
N75 G01 X0.0 Z-1.0;
N80 G03 X10.0 Z-6.0 R5.0;
N85 G01 X18.6 Z-9.0;
N90 Z-32.0; N09 X16.0 Z-54.0;
N95 X25.0 Z-60.0;
N100 Z-70.0;
N105 M105 S1200;
N110 G70 P05 Q11; (FINISHING CYCLE)
N115 G30 U0.0 W0.0; (HOME POSITION)
N120 ; M06 T0303 ;
N125 G00 X25.0 Z-11.0;
N130 G71 U1.0 R2.0;
N135 G71 P20 Q30 U0.2 W0.2 F0.2 S800; (MULTIPLE TURNING CYCLE)
N140 G01 X18.6 Z-11.0;
N145 G02 X8.0 Z-23.0 R18.0;
N150 G01 X10.0;
N155 Z-26.0;
N160 X8.0;
N165 X-28.0;
N170 X10.6;
N175 X-30.0;
N180 X18.6;
N185 Z-33.0;
N190 X18.6;
N195 Z-33.0;
N200 G02 X16.0 Z-52.0 R15 ;
N205 M04 S1200;
N210 G70 P20 Q30 ;
N215 G30 U0.0 W0.0 ;
N220 G00 X26.0 Z-61.0;
N225 G01 X23.5 F0.1 ; X 26.0;
N230 G30 U0.0 W0.0; (RETURN TO HOME POSTION)
N235 M30 ; (PROGRAM END)
KING
(120 X 45) WORKPIECE DIMENSION
O0144;
N5 G95 S1000 F.1 M3;
N10 T0101; (TURNING TOOL)
N15 G0 X45 Z0; (POSITION)
N20 Z-9;
N25 G77 R10;
N30 G77 X3 Z-9.231 P1000 Q1000 R0; (CUT-IN CYCLE IN X)
N35 M0;
N40 T0303; (FINISHING TOOL)
N45 G0 X45 Z0;
N50 G75 U40 W0 R10;
N55 G75 P60 Q130 U0 W0;
N60 G1 X3 Z0;
N65 Z-3;
N70 X8;
N75 X9 Z-3.5;
N80 Z-5.5
N85 X8 Z-6;
N90 X3 Z-9.231;
N95 G3 X8 Z-17 R4.5;
N100 G7 X26 G-21;
N105 Z-22;
N110 X14 Z-34;
N115 G3 X14 Z-37 R1.5;
N120 X14 Z-40 R1.5;
N125 G7 X31.3 Z-44.15;
N130 G3 X33 Z-47 R1.5;
N135 M0;
N140 T0505; (FINISHING TOOL)
N145 G0 X45 X-107;
N150 G75 U35 W-107 R10; (PATTERN REPEATING)
N155 G75 P160 Q205 U0 W0;
N160 X36 Z-106
N170 Z-101;
N180 G3 X36 Z-90.48 R7;
N185 G1 X21 Z-87;
N190 G2 X21 Z-82 R4;
N195 X20.02 Z-76.38 R7;
N200 G7 X14 Z-47;
N205 X33;
N210 G0 X45;
N220 Z0;
N225 M30; (PROGRAM END)
IN PARTIAL FULFILLMENT OF THE REQUIREMENTS FOR THE MODERN MACHINING PROCESSES (MT 323) SUBJECT

TECHNOLOGICAL UNIVERISTY OF THE PHILIPPINES – VISAYAS

SUBMITTED BY:
MARTOS, MARC KLINT R.

ME – 3A
DECEMBER 5, 2017

ENGR. JOEL SUMUGAT