Hempaline

tank linings
Chemical resistance guide
Chemical resistance guide Chemical resistance guide

Chemical
resistance
guide
for the Hempaline range
Hempel protective coatings produce the most versitile
range of chemically resistant linings on the market.

This guide is intended to provide a summary of the capabilities

of the Hempel linings offer. It does not contain all the linings
in the Hempel offer and the chemicals listed are not the limit
of chemicals to which Hempels linings are resistant.

Hempel supply linings suitable for a wide variety of applications

including, but not limited to: internal lining of above and below
ground storage tanks, internal lining for process vessels and
piping, external lining of buried tanks, vessels and equipment.

Hempel also provide a range of linings suitable for use onto

concrete surfaces which protect against chemical, abrasion
and impact attack. Specialised systems are available which
can provide crack bridging solutions for applications where
concrete movement is expected.

Hempel aim to provide the highest levels of service in

selecting, specifying and applying the linings systems.
Please do not hesitate to contact us with any enquiries
or problems you have and we will provide you the best
solution to satisfy your requirements.

If any training or support is required for the actual application

of the lining Hempel have specialists who can support the
local Technical Service Representatives if this is necessary.

2 3
Chemical resistance guide Chemical resistance guide

Specific notes
Introduction Product storage temperature
Hempel provides guidance on the resistance of tank linings to Chemical resistance is recorded as the maximum
those products which are commonly stored in bulk quantities. continuous storage temperature (loading temperatures
An explanation of the notations against each product is may be up to 10°C higher than the storage temperature).
as follows:
In certain circumstances some products have been
demonstrated to be suitable for high temperature service
Notations explained
and the recorded value may be increased subject to
Note = Storage of product subject to the conditions
confirmation of the conditions - please consult your regional
of the specific chemical notes itemised.
linings technical representative.
1, 4 = Recommended provided the requirements
Care should be taken when storing high temperature
of notes 1 and 4 are met.
aqueous chemicals. Where large temperature differentials
exist between the chemicals and external tank wall there is a
NR = Not recommended for this service.
danger of the tank coating system being adversely affected
due to cold wall thermal shock. If temperature differences are
T = Testing is required to determine if this product
in excess of 30°C (54ºF), it is recommended that the tank
is suitable for this service.
is insulated to reduce thermal gradient.

Recommendations are based on laboratory test data, Coating discolouration

field service and/or practical experience. Some stored products may cause discolouration
or staining of the surface of the coating under certain
Performance is subject to application and cure in storage conditions. Coatings may also become discoloured
strict accordance with the Product Data Sheets and by dyes etc. which are added to products (e.g. to petroleum
project specification. products for tax exemption purposes). This colour change
does not affect the chemical resistance properties of
The chemical resistance information included in this the coating.
document is for materials cured under normal ambient
conditions. Post-curing can in some cases improve the Tank cleaning
chemical resistance of certain linings (and also reduce Hempel does not advise on methods of tank cleaning,
any risk of contamination in some critical chemicals) except where cleaning methods may cause damage to
consult Hempel. the coating. Expert advice should be sought from one
of the specialist tank cleaning companies.
All concentrations listed are aqueous, unless
otherwise noted. Before use, any cleaning chemicals should be tested
to determine if they have any detrimental effect on the
Substrates and primers lining material.
The resistance quoted in the guide refers to the coating
system being applied directly to mild steel that has been Mixtures
prepared to the standard quoted on the Product Data Sheet For mixtures of materials it may not simply be a case
or over an approved primer. Application to alternative primers of the chemicals resistance list for the components.
and substrates is possible.
Mixtures can behave differently to the sum of their
components. Please consult Hempel to confirm suitability
of lining schemes for chemical blends

4 5
Chemical resistance guide Chemical resistance guide

Product notes
Storage of products subject to the conditions to the (4) Materials with special purity requirements Important notes
specific chemical notes itemised Many of the lining systems in this product resistance In accordance with our policy of continuous product
guide are resistant to materials which have specific purity development the information in this document may be
(1) Water miscible and hydrolysable chemicals requirements, and these may require global, regional or modified from time to time and you should check with
These products are susceptible to hydrolysis in the presence company approvals/certifcation to enable their use for your local Hempel representative that you have the
of water to form compounds which are potentially damaging this service. most up-to date version.
to the coating.
Regulatory approvals for food/water contact vary by country Failure to comply with the requirements of the latest
These products are only acceptable for storage if they are and region. version of this chemical product resistance guide that
pure, essentially neutral and are carried under completely apply to the products to be stored will invalidate any
dry conditions. The use of a lining inside a jet fuel storage tank may require a guarantee given by Hempel for the coating system as
specific approval from a military or commercial organisation. applied to the storage tank or vessel.
(2) Vegetable and animal oils and fats Hempel have materials with globally recognised certification
Vegetable and animal oil, fats etc. are esters of polyols Subject to the above, all products supplied and
with fatty acids and nearly always contain free fatty acid. Other materials may require high purity (for example fibre technical advice given, are subject to Hempel’s
If in contact with water, especially at higher temperatures, grade MEG) and it is important to consider this when making standard conditions of sale.
these can saponify, resulting in increased free fatty acid a selection.
content. Free fatty acids can be very aggressive to tank
coatings. Thus, during loading, storage and discharge the Please consult Hempel for the status of approvals in your
acid values should not exceed the values shown below. country/region.
Acid value measured in accordance with ISO 660 (1996)
is the only accepted method to determine a cargo’s suitability (5) Generically identified materials
for storage. The free fatty acid percentages are a guide only These products are believed to be suitable for storage in the
as the acid value is dependant on the molecular weight indicated tank lining since they seem to be generically similar
of the fatty acid(s). to products successfully stored. Since the composition
may vary, a detailed specification for the product to be
Hempaline 400, Hempaline 630, Hempaline 640. stored must be supplied to Hempel – a recommendation on
Hempaline 650 - maximum acid value (acc.to ISO 660 the product notation can usually be made without testing,
(1996)) - 30 mg KOH/g oil. however in some cases confirming tests may be required.

Hempaline 500, 560, 570 and 740 - maximum acid value (6) Discolouration of acids on storage
(acc.to ISO 660 (1996)) - no limit. Storage of strong acids (such as Hydrochloric, Sulphuric
and Phosphoric acid) incontact with chemically resistant
(3) Caustic products linings may cause discoluration of the lining. This will not
Dilute caustic solutions can be very aggressive towards influence the corrosion protection, however, with prolonged
tank linings. Care should be taken when cleaning tanks immersion there is a risk of discolouration of the stored acid.
containing caustic materials to avoid prolonged contact If purity is a requirement alternative stoarage solutions
of the lining with dilute solutions. may be required.

(7) Return to service

For most services the Hempaline epoxies may
be returned to service after 72 hours (standard
grade) and 24 hours (fast return to service grade)
at 20°C/68°F. For the storage of some more
aggressive chemicals it is recommended that
the cure time is extended to 7 days (standard
grade) and 72 hours (fast return to service grade)
at 20°C/68°F to achieve the maximum service
temperature.

6 7
Chemical resistance guide Chemical resistance guide

Chemical Hempaline 400 Hempaline 630 Hempaline 640 Hempaline 650 Hempaline 500 Hempaline 560 Hempaline 570 Hempaline 740/750
Solvent free epoxy Solvent free Glass flake Abrasion resistant Standard vinyl ester Trowel applied glass Reinforced vinyl ester Flake filled novolac
novolac epoxy novolac solvent free solvent free epoxy flake vinyl ester lining vinyl esters
epoxy novolac novolac
1, 2, 3, 5 - Tetramethylbenzene 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 25°C / 77°F 25°C / 77°F 25°C / 77°F 40°C / 104°F
1 - Heptene 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
1 - Pentene 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
2 - Chloroethanol NR NR NR NR 25°C / 77°F 25°C / 77°F 26 25°C / 77°F
2 - Heptanone T T T T 25°C / 77°F 25°C / 77°F 25°C / 77°F 40°C / 104°F
2 - Methoxyethanol T T T T 40°C / 104°F 93°C / 200°F 71°C / 160°F 82°C / 180°F
3 - Chloroprene T T T T NR NR NR NR
Acetic Acid, <25% NR NR NR NR 50°C / 122°F 40°C / 104°F 50°C / 122°F 60°C / 140°F
Acetic Acid, 10-50% NR NR NR NR 50°C / 122°F 40°C / 104°F 71°C / 160°F 60°C / 140°F
Acetic Acid, 1-5% NR NR NR NR 40°C / 104°F 82°C / 180°F 71°C / 160°F 60°C / 140°F
Acetic Acid, 50% to (Glacial) 100% NR NR NR NR NR NR NR 40°C / 104°F
Acetic Acid, 5-10% NR NR NR NR 50°C / 122°F 50°C / 122°F 50°C / 122°F 60°C / 140°F
Acetic Anhydride NR NR NR NR NR NR NR 40°C / 104°F
Acetone NR T T T T NR NR NR
Acetonitrile T T T T NR NR NR NR
Acetophenone T T T T T T T T
Acrylonitrile T T T T NR NR NR T
Aircraft Gasoline 50°C / 122°F (4) 50°C / 122°F (4) 50°C / 122°F 50°C / 122°F 40°C / 104°F 82°C / 180°F 82°C / 180°F 60°C / 140°F
Airturbo Fuel 50°C / 122°F (4) 50°C / 122°F (4) 50°C / 122°F 50°C / 122°F 40°C / 104°F 82°C / 180°F 82°C / 180°F 40°C / 104°F
Alcohol, Linear Primary C-12/15 50°C / 122°F (4) 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F
Alcoholic Beverages, NOS T T T T T T T NR
Alkylate 40°C / 104°F 50°C / 122°F (5) 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F
Allyl Alcohol 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F NR NR NR 25°C / 77°F
Alpha Olefin C-6/18 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Aminoethoxyethanol (Diglycolamine) (DGA) NR NR NR NR NR NR NR NR
Ammonium Hydroxide, 0-5% T T T T 40°C / 104°F NR 40°C / 104°F 40°C / 104°F
Ammonium Hydroxide, 21-30% T T T T 40°C / 104°F NR 40°C / 104°F NR
Ammonium Hydroxide, 6-20% T T T T 40°C / 104°F NR 40°C / 104°F NR
Amyl Aldehyde NR NR NR NR NR NR NR 25°C / 77°F
Aniline NR NR NR NR NR NR NR NR
Aromatic 100 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 25°C / 77°F 25°C / 77°F 25°C / 77°F 40°C / 104°F
Arsenious Acid NR T T T 50°C / 122°F 40°C / 104°F 60°C / 140°F 60°C / 140°F
AVGAS 100LL (Low Benzene) 40°C / 104°F (4) 50°C / 122°F (4) 50°C / 122°F 50°C / 122°F 40°C / 104°F 60°C / 140°F 60°C / 140°F T
Aviation Alkylates 40°C / 104°F (4) 50°C / 122°F (4) 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
Aviation Fuel 40°C / 104°F (4) 50°C / 122°F (4) 50°C / 122°F (4) 50°C / 122°F (4) 40°C / 104°F (4) 60°C / 140°F (4) 60°C / 140°F (4) 60°C / 140°F
Benzene 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F NR NR NR 40°C / 104°F
Benzene Sulphonic Acid NR NR NR NR 40°C / 104°F 40°C / 104°F 60°C / 140°F 60°C / 140°F
Benzoic Acid NR NR NR NR 40°C / 104°F 93°C / 200°F 71°C / 160°F 60°C / 140°F
Benzyl acetate T T T T NR NR NR NR
Benzyl Alcohol T T T T NR NR NR 40°C / 104°F
Benzyl Chloride T T T T NR NR NR NR

(Number) refer to notes on pages 6 & 7.

Please check with your local sales representative for the latest information.
8 9
Chemical resistance guide Chemical resistance guide

Chemical Hempaline 400 Hempaline 630 Hempaline 640 Hempaline 650 Hempaline 500 Hempaline 560 Hempaline 570 Hempaline 740/750
Solvent free epoxy Solvent free Glass flake Abrasion resistant Standard vinyl ester Trowel applied glass Reinforced vinyl ester Flake filled novolac
novolac epoxy novolac solvent free solvent free epoxy flake vinyl ester lining vinyl esters
epoxy novolac novolac
Benzyl Dichloride T T T T NR NR NR NR
Biodiesel B100 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F
Biodiesel B20 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F
Biodiesel B5 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F
Bioethanol 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F NR NR NR 40°C / 104°F
Bunker C 60°C / 140°F 82°C / 180°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F
Bunker Fuel 60°C / 140°F 82°C / 180°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F
Butanol 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Butyl Acetate T T T T NR NR NR 25°C / 77°F
Butyl Amine T T T T NR NR NR T
Butyl Ether T T T T 50°C / 122°F 50°C / 122°F 51 60°C / 140°F
Butylbenzyl Phthalate T T T T 40°C / 104°F 71°C / 160°F 40°C / 104°F 60°C / 140°F
Butylene Glycol T T T T 50°C / 122°F 40°C / 104°F 40°C / 104°F 50°C / 122°F
ButyraIdehyde NR NR NR NR NR NR NR 25°C / 77°F
Butyric Acid NR NR NR NR NR T NR 50°C / 122°F
Butyric Acid, 0-5% NR NR NR NR 40°C / 104°F 40°C / 104°F 60°C / 140°F 60°C / 140°F
Butyric Acid, 51-100% NR NR NR NR NR NR NR 40°C / 104°F
Butyric Acid, 6-50% NR NR NR NR 40°C / 104°F 40°C / 104°F 60°C / 140°F 60°C / 140°F
Butyrolactone NR T T T NR NR NR T
Calcium Bromide Solutions T 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 50°C / 122°F
Calcium Carbonate Slurries 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F
Calcium Chloride Solutions 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F
Carbon Disulfide NR T T T NR NR NR NR
Calcium Sulphate 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F NR NR NR 60°C / 140°F
Carbon Tetrachloride NR NR NR NR NR NR NR NR
Chlorobenzene T T T T NR NR NR NR
Chloroform T T T T NR NR NR NR
Citric Acid T T T T 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F
Clarified Crude Oils 71°C / 160°F 93°C / 200°F 93°C / 200°F 93°C / 200°F 40°C / 104°F 93°C / 200°F 82°C / 180°F 82°C / 180°F
Crude Oil - Sour, High Sulphur 71°C / 160°F 93°C / 200°F (7) 93°C / 200°F (7) 93°C / 200°F (7) 40°C / 104°F 93°C / 200°F 82°C / 180°F 82°C / 180°F
Crude Oil - Sweet, Low Sulphur 71°C / 160°F 93°C / 200°F 93°C / 200°F 93°C / 200°F 40°C / 104°F 93°C / 200°F 82°C / 180°F 82°C / 180°F
Cumene (Isopropyl Benzene) 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 25°C / 77°F 25°C / 77°F 25°C / 77°F 50°C / 122°F
Cycloheptane 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 60°C / 140°F
Cyclohexane 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Cyclohexanol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Dibutyl Ether T T T T NR NR NR NR
Dichloromethane NR T T T NR NR NR NR
Diesel 60°C / 140°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 50°C / 122°F 71°C / 160°F 71°C / 160°F 71°C / 160°F
Diethanolamine NR T T T T T T 40°C / 104°F
Diethyl Ether T T T T NR NR NR NR
Diethylene Glycol T T T T 40°C / 104°F 40°C / 104°F 40°C / 104°F 60°C / 140°F

(Number) refer to notes on pages 6 & 7.

Please check with your local sales representative for the latest information.
10 11
Chemical resistance guide Chemical resistance guide

Chemical Hempaline 400 Hempaline 630 Hempaline 640 Hempaline 650 Hempaline 500 Hempaline 560 Hempaline 570 Hempaline 740/750
Solvent free epoxy Solvent free Glass flake Abrasion resistant Standard vinyl ester Trowel applied glass Reinforced vinyl ester Flake filled novolac
novolac epoxy novolac solvent free solvent free epoxy flake vinyl ester lining vinyl esters
epoxy novolac novolac
Distillates, Straight Run (Kerosene) 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 82°C / 180°F 71°C / 160°F 50°C / 122°F
Dodecane 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
Dodecanol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 50°C / 122°F
Domestic Fuel Oil 60°C / 140°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 71°C / 160°F 71°C / 160°F 71°C / 160°F
Epichlorohydrin T T T T NR NR NR NR
ETBE 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F NR NR NR 40°C / 104°F
Ethanol 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F NR 25°C / 77°F 25°C / 77°F 40°C / 104°F
Ethyl Acetate NR T T T NR NR NR NR
Ethyl Benzene 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 25°C / 77°F 25°C / 77°F 25°C / 77°F 40°C / 104°F
Ethylene Dichloride (Edc) NR T T T NR NR NR NR
Ethylene Glycol 40°C / 104°F (4) 50°C / 122°F (4) 50°C / 122°F (4) 50°C / 122°F (4) 40°C / 104°F (4) 93°C / 200°F (4) 71°C / 160°F (4) 82°C / 180°F (4)
Ethylhexanol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F
Ethyltoluene 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 25°C / 77°F 25°C / 77°F 25°C / 77°F 40°C / 104°F
Formic Acid NR NR NR NR 25°C / 77°F 25°C / 77°F 25°C / 77°F 40°C / 104°F
Fuel Oil Light 60°C / 140°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 71°C / 160°F 71°C / 160°F 71°C / 160°F
Fuel Oil No.1 (Kerosene, Destillate No.1) 40°C / 104°F 60°C / 140°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 71°C / 160°F
Fuel Oil No.2 (Diesel Oil, Destillate No.2, Bunker A) 40°C / 104°F 60°C / 140°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 71°C / 160°F
Fuel Oil No.4 (Mix of Destillate and Residual Oils) 40°C / 104°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 71°C / 160°F 71°C / 160°F 71°C / 160°F
Fuel Oil No.5 (Residual Fuel Oil, Bunker B) 60°C / 140°F 82°C / 180°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 71°C / 160°F 71°C / 160°F 71°C / 160°F
Fuel Oil No.6 (Heavy Fuel Oil, Residual Fuel Oil, Bunker C) 60°C / 140°F 82°C / 180°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 71°C / 160°F 71°C / 160°F 71°C / 160°F
Furfural T T T T 40°C / 104°F 82°C / 180°F 82°C / 180°F NR
Gas Oil 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 71°C / 160°F 71°C / 160°F 71°C / 160°F
Gas Plant Naphtha 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
Gasoline, < 50% Ethanol 40°C / 104°F (7) 40°C / 104°F (7) 40°C / 104°F (7) 40°C / 104°F (7) 25°C / 77°F 25°C / 77°F 25°C / 77°F 40°C / 104°F
Gasoline, <10% Methanol 40°C / 104°F (7) 40°C / 104°F (7) 40°C / 104°F (7) 40°C / 104°F (7) 25°C / 77°F 25°C / 77°F 25°C / 77°F 40°C / 104°F
Gasoline, <15% ETBE 40°C / 104°F (7) 40°C / 104°F (7) 40°C / 104°F (7) 40°C / 104°F (7) 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F
Gasoline, <15% MTBE 40°C / 104°F (7) 40°C / 104°F (7) 40°C / 104°F (7) 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F
Gasoline, 10-30% Methanol NR T T T NR NR NR 25°C / 77°F
Gasoline, Aviation 40°C / 104°F (4) 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F (4) 60°C / 140°F (4) 60°C / 140°F (4) 60°C / 140°F
Gasoline, E85 NR 40°C / 104°F 40°C / 104°F 40°C / 104°F 25°C / 77°F 25°C / 77°F 25°C / 77°F 40°C / 104°F
Gasoline, Premium Unleaded 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F
Gasoline, Regular Unleaded 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F
Glycerine T T T T 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F
Glycol T 50°C / 122°F (4) 50°C / 122°F (4) 50°C / 122°F (4) 40°C / 104°F (4) 93°C / 200°F (4) 71°C / 160°F (4) 82°C / 180°F (4)
Heart Cut Distillate (Exxon Solvent Blend) 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F T T T 40°C / 104°F
Heating Oil 60°C / 140°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 60°C / 140°F 71°C / 160°F 71°C / 160°F 71°C / 160°F
Heavy Aromatic Naphtha 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F
Heptane (All Isomers) 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F
Heptanol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Hexadecane 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Hexadecanol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F

(Number) refer to notes on pages 6 & 7.

Please check with your local sales representative for the latest information.
12 13
Chemical resistance guide Chemical resistance guide

Chemical Hempaline 400 Hempaline 630 Hempaline 640 Hempaline 650 Hempaline 500 Hempaline 560 Hempaline 570 Hempaline 740/750
Solvent free epoxy Solvent free Glass flake Abrasion resistant Standard vinyl ester Trowel applied glass Reinforced vinyl ester Flake filled novolac
novolac epoxy novolac solvent free solvent free epoxy flake vinyl ester lining vinyl esters
epoxy novolac novolac
Hexane (All Isomers) 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Hexanol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Hexene 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Hydrochloric Acid, pH >3 NR 40°C / 104°F (6) 40°C / 104°F (6) 40°C / 104°F (6) 40°C / 104°F (6) 60°C / 140°F (6) 60°C / 140°F (6) 60°C / 140°F (6)
Hydrochloric Acid, 0-9% NR NR NR NR 50°C / 122°F (6) 60°C / 140°F (6) 60°C / 140°F (6) 60°C / 140°F (6)
Hydrochloric Acid, 10-19% NR NR NR NR 40°C / 104°F (6) 40°C / 104°F (6) 60°C / 140°F (6) 60°C / 140°F (6)
Hydrochloric Acid, 20-30% NR NR NR NR 40°C / 104°F (6) 40°C / 104°F (6) 50°C / 122°F (6) 60°C / 140°F (6)
Hydrogen Peroxide NR T T T NR NR NR NR
Iso Octane 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
Isobutyl Alcohol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Isodecanol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Isohexanol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Isononyl Alcohol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F
Isopentane 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 60°C / 140°F
Isopropanol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Isopropyl Toluene 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F
Jet Fuel, JP4, JP5, JP8 & Jet A 40°C / 104°F 50°C / 122°F (4) 50°C / 122°F (4) 50°C / 122°F (4) 40°C / 104°F (4) 40°C / 104°F (4) 71°C / 160°F (4) 60°C / 140°F (4)
Kerosene 40°C / 104°F 60°C / 140°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F
Low Aromatic White Spirit 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
Lube Oil 60°C / 140°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 71°C / 160°F 71°C / 160°F 82°C / 180°F
Magnesium Chloride 25°C / 77°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F
MEG/Water Mixtures 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 82°C / 180°F
Meta Xylene 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F NR NR NR 50°C / 122°F
Methanol NR NR NR NR NR NR NR 25°C / 77°F
Methyl Acrylate T T T T NR NR NR NR
Methyldiethanolamine (MDEA) NR 50°C / 122°F 50°C / 122°F 50°C / 122°F T T T 50°C / 122°F
Methyldiethanolamine (MDEA) - 50% in Water NR 50°C / 122°F 50°C / 122°F 50°C / 122°F T T T 50°C / 122°F
Methyl Ethyl Ketone T T T T NR NR NR NR
Methyl Formate T T T T NR NR NR NR
Methyl Toluene 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F NR NR NR 40°C / 104°F
Methylamyl Alcohol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F
Methylcyclohexane 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Middle Oil 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F T T T 40°C / 104°F
Mineral Oil - Tellus Oil 50°C / 122°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 82°C / 180°F 71°C / 160°F 60°C / 140°F
Mineral Oil - White 50°C / 122°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 82°C / 180°F 71°C / 160°F 60°C / 140°F
Mineral Seal Oil (Lube Oil) 50°C / 122°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 82°C / 180°F 71°C / 160°F 60°C / 140°F
Mineral Spirits 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 60°C / 140°F
Mineral Spirits #10 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 60°C / 140°F
Mineral Spirits #3 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 60°C / 140°F
Mineral Spirits #4 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 60°C / 140°F
Molasses, ph >4 T T T T 40°C / 104°F 93°C / 200°F 50°C / 122°F 60°C / 140°F

(Number) refer to notes on pages 6 & 7.

Please check with your local sales representative for the latest information.
14 15
Chemical resistance guide Chemical resistance guide

Chemical Hempaline 400 Hempaline 630 Hempaline 640 Hempaline 650 Hempaline 500 Hempaline 560 Hempaline 570 Hempaline 740/750
Solvent free epoxy Solvent free Glass flake Abrasion resistant Standard vinyl ester Trowel applied glass Reinforced vinyl ester Flake filled novolac
novolac epoxy novolac solvent free solvent free epoxy flake vinyl ester lining vinyl esters
epoxy novolac novolac
Monoethylene Glycol 40°C / 104°F (4) 50°C / 122°F (4) 50°C / 122°F (4) 50°C / 122°F (4) 40°C / 104°F (4) 93°C / 200°F (4) 71°C / 160°F (4) 82°C / 180°F (4)
Monoethanolamine (MEA) NR NR NR NR NR NR NR NR
Motor Oil 50°C / 122°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 82°C / 180°F 82°C / 180°F 82°C / 180°F
MTBE T 40°C / 104°F 40°C / 104°F 40°C / 104°F NR NR NR 25°C / 77°F
Naphta, Heartcut Distillate Oil (Maximum 10% Benzene) 40°C / 104°F 60°C / 140°F (5) 60°C / 140°F (5) 60°C / 140°F (5) 40°C / 104°F (5) 40°C / 104°F (5) 40°C / 104°F (5) 60°C / 140°F (5)
Naphta, Heavy (Maximum 10% Benzene) 40°C / 104°F 60°C / 140°F (5) 60°C / 140°F (5) 60°C / 140°F (5) 40°C / 104°F (5) 40°C / 104°F (5) 40°C / 104°F (5) 60°C / 140°F (5)
Naphta, Petroleum (Maximum 10% Benzene) 40°C / 104°F 60°C / 140°F (5) 60°C / 140°F (5) 60°C / 140°F (5) 40°C / 104°F (5) 40°C / 104°F (5) 40°C / 104°F (5) 60°C / 140°F (5)
Naphta, Sour (Maximum 10% Benzene) 40°C / 104°F 60°C / 140°F (5) 60°C / 140°F (5) 60°C / 140°F (5) 40°C / 104°F (5) 40°C / 104°F (5) 40°C / 104°F (5) 60°C / 140°F (5)
Naphta, Sweet (Maximum 10% Benzene) 40°C / 104°F 60°C / 140°F (5) 60°C / 140°F (5) 60°C / 140°F (5) 40°C / 104°F (5) 40°C / 104°F (5) 40°C / 104°F (5) 60°C / 140°F (5)
Nitric Acid, >40% NR NR NR NR NR NR NR NR
Nitric Acid, 0-5% NR NR NR NR 50°C / 122°F 60°C / 140°F 60°C / 140°F 50°C / 122°F
Nitric Acid, 11-20% NR NR NR NR 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F
Nitric Acid, 21-30% NR NR NR NR 25°C / 77°F 25°C / 77°F 40°C / 104°F 40°C / 104°F
Nitric acid, 31-40% NR NR NR NR NR NR NR NR
Nitric Acid, 6-10% NR NR NR NR 50°C / 122°F 60°C / 140°F 60°C / 140°F 50°C / 122°F
Nitric Acid, pH >3 NR 40°C / 104°F 50°C / 122°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 60°C / 140°F
Nonane 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
Nonanol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Nonene 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 60°C / 140°F
Octane 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
Octanol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 60°C / 140°F
Oil, Petroleum 60°C / 140°F 40°C / 104°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 82°C / 180°F 82°C / 180°F 60°C / 140°F
Olefin Mixture C5-C12 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
Pale Oil 60°C / 140°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 60°C / 140°F 60°C / 140°F 71°C / 160°F
Paraffinic Oil, White 60°C / 140°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 71°C / 160°F 40°C / 104°F 60°C / 140°F
Pentane 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Phosphoric Acid NR NR NR NR 40°C / 104°F (6) 50°C / 122°F (6) 50°C / 122°F (6) 60°C / 140°F (6)
Polypropylene Glycol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
Potassium Bromide Solutions T 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 50°C / 122°F
Potassium Carbonate Solutions 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
Potassium Chlorate Solutions 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
Potassium Chloride Solutions 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 82°C / 180°F 71°C / 160°F 60°C / 140°F
Potassium Cyanide Solutions T T T T 40°C / 104°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
Potassium Hydroxide, >30% 40°C / 104°F (3) 60°C / 140°F (3) T 60°C / 140°F (3) NR NR T NR
Potassium hydroxide, 0-3% T T T T NR NR T NR
Potassium Hydroxide, 3-30% 40°C / 104°F (3) 60°C / 140°F (3) T 60°C / 140°F (3) NR NR T NR
Potassium Nitrate Solutions 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 82°C / 180°F 71°C / 160°F 60°C / 140°F
Propane 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Propanol 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Pyrolysis Fuel (Fuel Oil) 50°C / 122°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 50°C / 122°F 71°C / 160°F 71°C / 160°F 71°C / 160°F
Secondary Amyl Alcohol 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F

(Number) refer to notes on pages 6 & 7.

Please check with your local sales representative for the latest information.
16 17
Chemical resistance guide Chemical resistance guide

Chemical Hempaline 400 Hempaline 630 Hempaline 640 Hempaline 650 Hempaline 500 Hempaline 560 Hempaline 570 Hempaline 740/750
Solvent free epoxy Solvent free Glass flake Abrasion resistant Standard vinyl ester Trowel applied glass Reinforced vinyl ester Flake filled novolac
novolac epoxy novolac solvent free solvent free epoxy flake vinyl ester lining vinyl esters
epoxy novolac novolac
Shell Kerex (Mineral Spirits) 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 60°C / 140°F
Shell Lube Oils 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 82°C / 180°F 82°C / 180°F 82°C / 180°F
Shellsol 'A' (Trimethyl Benzenes) 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F NR NR T 40°C / 104°F
Shellsol A100 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F NR NR T 40°C / 104°F
Sodium Chloride Solutions 60°C / 140°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 50°C / 122°F 71°C / 160°F 71°C / 160°F 82°C / 180°F
Sodium Hydroxide, >30% 40°C / 104°F (3) 60°C / 140°F (3) T 60°C / 140°F (3) NR NR T NR
Sodium Hydroxide, 0-3% T T T T NR NR T NR
Sodium Hydroxide, 3-30% 40°C / 104°F (3) 60°C / 140°F (3) T 60°C / 140°F (3) NR NR T NR
Solvent Naphtha 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F
Solvesso 100 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 25°C / 77°F 25°C / 77°F 25°C / 77°F 50°C / 122°F
Solvesso 150 40°C / 104°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 25°C / 77°F 25°C / 77°F 25°C / 77°F 50°C / 122°F
Styrene Monomer T 40°C / 104°F 40°C / 104°F 40°C / 104°F NR NR NR 40°C / 104°F
Sulphuric Acid, >75% NR NR NR NR NR NR NR NR
Sulphuric Acid, 0-20% NR NR NR NR 40°C / 104°F (6) 82°C / 180°F (6) 71°C / 160°F (6) 60°C / 140°F (6)
Sulphuric Acid, 21-50% NR NR NR NR 40°C / 104°F (6) 71°C / 160°F (6) 71°C / 160°F (6) 60°C / 140°F (6)
Sulphuric Acid, 51-71% NR NR NR NR 40°C / 104°F (6) 40°C / 104°F (6) 60°C / 140°F (6) 50°C / 122°F (6)
Sulphuric Acid, 71-75% NR NR NR NR 40°C / 104°F (6) 40°C / 104°F (6) 40°C / 104°F (6) 40°C / 104°F (6)
Sulphuric Acid, pH >3 T 40°C / 104°F (6) 40°C / 104°F (6) 40°C / 104°F (6) 40°C / 104°F (6) 60°C / 140°F (6) 60°C / 140°F (6) 60°C / 140°F (6)
Tetrachloroethane T T T T NR NR NR 50°C / 122°F
Tetrahydrofuran T T T T NR NR NR NR
Toluene 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F NR NR NR 40°C / 104°F
Toluene Disocyanate T T T T NR NR NR NR
Transformer Oil 60°C / 140°F 71°C / 160°F 71°C / 160°F 71°C / 160°F 40°C / 104°F 71°C / 160°F 71°C / 160°F 71°C / 160°F
Triethyl Benzene 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 25°C / 77°F 25°C / 77°F 25°C / 77°F 50°C / 122°F
Triethylene Glycol T T T T 40°C / 104°F 93°C / 200°F 71°C / 160°F 60°C / 140°F
Urea Solution T 40°C / 104°F 40°C / 104°F 40°C / 104°F 40°C / 104°F 71°C / 160°F 71°C / 160°F 60°C / 140°F
VM&P Naphtha T 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F
Water, Brackish 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 50°C / 122°F 71°C / 160°F 71°C / 160°F 82°C / 180°F
Water, Deionised 50°C / 122°F 60°C / 140°F (4, 7) 60°C / 140°F (4, 7) 60°C / 140°F (4, 7) 50°C / 122°F (4) 71°C / 160°F (4) 71°C / 160°F (4) 82°C / 180°F (4)
Water, Demineralised 50°C / 122°F 60°C / 140°F (4, 7) 60°C / 140°F (4, 7) 60°C / 140°F (4, 7) 50°C / 122°F (4) 71°C / 160°F (4) 71°C / 160°F (4) 82°C / 180°F (4)
Water, Distilled 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 50°C / 122°F 71°C / 160°F 71°C / 160°F 82°C / 180°F
Water, Fresh 50°C / 122°F 60°C / 140°F (4) 60°C / 140°F (4) 60°C / 140°F (4) 50°C / 122°F (4) 71°C / 160°F (4) 71°C / 160°F (4) 82°C / 180°F (4)
Water, Sea 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 50°C / 122°F 71°C / 160°F 71°C / 160°F 82°C / 180°F
Water - Produced 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 50°C / 122°F 71°C / 160°F 71°C / 160°F 82°C / 180°F
White Mineral Oil 60°C / 140°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 40°C / 104°F 82°C / 180°F 71°C / 160°F 60°C / 140°F
White Oils 60°C / 140°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 82°C / 180°F 71°C / 160°F 60°C / 140°F
White Spirit 100 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 60°C / 140°F
White Spirit 150 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
White Spirit 160/182 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 40°C / 104°F 40°C / 104°F 60°C / 140°F
White Spirits 40°C / 104°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 50°C / 122°F 60°C / 140°F
Xylene 50°C / 122°F 60°C / 140°F 60°C / 140°F 60°C / 140°F 25°C / 77°F 25°C / 77°F 25°C / 77°F 50°C / 122°F

(Number) refer to notes on pages 6 & 7.

Please check with your local sales representative for the latest information.
18 19
hempel.com

Since 1915 Hempel has been a world-leading

coatings specialist, providing protection and
inspiration to the world around us. Today we have
over 5,500 people in 80 countries delivering
trusted solutions in the protective, decorative,
marine, container, industrial and yacht markets.
This includes many recognised brands like
Crown Paints, Schaepman and Jones-Blair.

Hempel is proudly owned by the Hempel

Foundation, which supports cultural, humanitarian
and scientific causes across the world.

The Hempel Group Head Office

Hempel A/S
Lundtoftegaardsvej 91
2800 Kgs. Lyngby
Denmark

Tel: +45 4593 3800

Email: hempaline@hempel.com
hempaline.hempel.com V2_JUL_16