Oxygen Sensor OOM109
Use the advantages:
• Designed and manufactured according to EN ISO 13485
• Designed for main stream application
• Accurate and reliable ultra fast response
• Excellent signal stability
• High product quality
• Short delivery times
• Technical support
• Made in Germany
From standard sensors to customized sensors Mechanical drawing (dimension in mm)
Experienced EnviteC engineers analyze customer require-
Ø14,5
ments. This input is used for different standard and OEM ap-
plications, and ongoing support is provided right up to the final
integraton in the solution.
34,8
EnviteC designs customized sensors characterized by a maxi-
41,4
mum possible degree of precision, for example with different
signal levels or temperature compensation elements.
Intendend use
The EnviteC medical oxygen sensors of series OOM109 are in- M16x1 (5/8-24 UNEF)*
tended as oxygen-sensing component of an oxygen analyzer
that measures oxygen concentration in breathing gas mixtures Locking Latch
or for breath by breath analysis of oxygen concentration in (-) (+)
breath gases.*
3PIN Molex Connector
General tolerances ISO 2768-c
*Intermediate thread: Metric / Unified Extra Fine
For more information please contact us! We look forward to assisting you either on the phone or in a personal talk.
Technical Specifications OOM109
Measurement range 0 % ... 100 % oxygen (at atmospheric pressure)
Nominal sensor lifetime ≥ 200 000 % volume oxygen hours
Output in ambient air 9 mV ... 13 mV
Electrical interface 3 pin (Molex® 22-11-1031)
Accuracy meets ISO 80601-2-55 requirements
Repeatability < 1 % volume O2 at constant temperature and pressure
Linearity error < 3 % relative
Response time < 360 ms to 90 % of final value
(tested on EnviteC test fixture with 3 liter /min flow)
Zero offset voltage < 50 µV in 100 % nitrogen, applied for 5 min
Cross interference on request
Influence of humidity -0.03 % rel. per % RH at 25 °C
Pressure range 0.7 bar ... 1.250 bar
Influence of pressure proportional to change in oxygen partial pressure
Influence of mechanical shock < 1 % relative after a fall from 1 m
Operating temperature 0 °C ... +45 °C
Temperature compensation built-in NTC compensation
Effect of temperature compensation (steady between +25 °C and +40 °C: 3 % relative error
state) between 0 °C and +50 °C: 8 % relative error
Operating humidity 0 % ... 99 % RH non-condensing
Long term output drift < 1 % volume oxygen per month
typically < -15 % relative over lifetime
Storage temperature -20 °C ... +50 °C
Recommended storage +5 °C ... +15 °C
Recommended load ≥ 10 kOhm
Warm-up time < 30 minutes, after replacement of sensor
Weight approximately 28 grams
Warranty period 9 months
Part number 01-00-0085
* The sensors are not designed to provide direct vital signs monitoring (measurement of parameters where erroneous results
could result in immediate danger to the patient). The sensor cross-sensitivity against anesthetic agents has not been tested.
Further information on request.
All specifications are applicable at standard conditions:
1013 hPa, 25 °C dry ambient air
Certified Quality Management
EnviteC is maintaining a quality management system, which
meets the requirements of EN ISO 13485 for medical devices.
EnviteC-Wismar GmbH Doc. No. 001-05-Datasheet_OOM109-1
a Honeywell Company December 2017
Technical information is subject
Alter Holzhafen 18, 23966 Wismar, Germany to change without notice!
Phone: +49 (0)3841-360-1 © 2017 Honeywell International Inc.
Phone: +49 (0)3841-360-200
Fax: +49 (0)3841-360-222 EnviteC by Honeywell reserves the
right to make changes in product
Internet: www.envitec.com specifications and adjust its production
Email: info@envitec.com at any time and without notice.
Oxygen Sensor OOM109-LF2
Use the advantages:
• Designed and manufactured according to EN ISO 13485
• Designed for side stream application
• Accurate and reliable ultra fast response
• Excellent signal stability
• High product quality
• Short delivery times
• Technical support
• Made in Germany
From standard sensors to customized sensors Mechanical drawing (dimension in mm)
Experienced EnviteC engineers analyze customer require- Ø29
ments. This input is used for different standard and OEM ap- 14,5
plications, and ongoing support is provided right up to the final
integraton in the solution.
EnviteC designs customized sensors characterized by a maxi-
40
mum possible degree of precision, for example with different
signal levels or temperature compensation elements.
Intendend use
7,5
The EnviteC medical oxygen sensors of series OOM109 are in-
IN
OUT
tended as oxygen-sensing component of an oxygen analyzer n29,9 Ø27
that measures oxygen concentration in breathing gas mixtures
intend for 1/16"
or for breath by breath analysis of oxygen concentration in OD tube
intend for Luer
breath gases.* connector
Locking Latch
(-) (+)
3PIN Molex
Connector
General tolerances ISO 2768-c
For more information please contact us! We look forward to assisting you either on the phone or in a personal talk.
Technical Specifications OOM109-LF2
Measurement range 0 % ... 100 % oxygen (at atmospheric pressure)
Nominal sensor lifetime ≥ 200 000 % volume oxygen hours
Output in ambient air 9 mV ... 13 mV
Electrical interface 3 pin (Molex® 22-11-1031)
Accuracy meets ISO 80601-2-55 requirements
Repeatability < 1 % volume O2 at constant temperature and pressure
Linearity error < 3 % relative
Response time < 360 ms to 90 % of final value
(tested on EnviteC test fixture with 3 liter /min flow)
Zero offset voltage < 50 µV in 100 % nitrogen, applied for 5 min
Cross interference on request
Influence of humidity -0.03 % rel. per % RH at 25 °C
Pressure range 0.7 bar ... 1.250 bar
Influence of pressure proportional to change in oxygen partial pressure
Influence of mechanical shock < 1 % relative after a fall from 1 m
Operating temperature 0 °C ... +45 °C
Temperature compensation built-in NTC compensation
Effect of temperature compensation (steady between +25 °C and +40 °C: 3 % relative error
state) between 0 °C and +50 °C: 8 % relative error
Operating humidity 0 % ... 99 % RH non-condensing
Long term output drift < 1 % volume oxygen per month
typically < -15 % relative over lifetime
Storage temperature -20 °C ... +50 °C
Recommended storage +5 °C ... +15 °C
Recommended load ≥ 10 kOhm
Warm-up time < 30 minutes, after replacement of sensor
Weight approximately 28 grams
Warranty period 9 months
Part number 01-00-0116
* The sensors are not designed to provide direct vital signs monitoring (measurement of parameters where erroneous results
could result in immediate danger to the patient). The sensor cross-sensitivity against anesthetic agents has not been tested.
Further information on request.
All specifications are applicable at standard conditions:
1013 hPa, 25 °C dry ambient air
Certified Quality Management
EnviteC is maintaining a quality management system, which
meets the requirements of EN ISO 13485 for medical devices.
EnviteC-Wismar GmbH Doc. No. 001-05-Datasheet_OOM109_LF2-1
a Honeywell Company December 2017
Technical information is subject
Alter Holzhafen 18, 23966 Wismar, Germany to change without notice!
Phone: +49 (0)3841-360-1 © 2017 Honeywell International Inc.
Phone: +49 (0)3841-360-200
Fax: +49 (0)3841-360-222 EnviteC by Honeywell reserves the
right to make changes in product
Internet: www.envitec.com specifications and adjust its production
Email: info@envitec.com at any time and without notice.
