100% found this document useful (1 vote)
560 views24 pages

Julie - Universal Car Emulator Programs:: Program Use

Uploaded by

cdoniguian
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
100% found this document useful (1 vote)
560 views24 pages

Julie - Universal Car Emulator Programs:: Program Use

Uploaded by

cdoniguian
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 24

1

Back to Main Page

Julie - Universal Car Emulator Programs:


Renault without CAN........................................................................................................2
Renault without CAN old ECUs.......................................................................................2

Program Use
• Sirius 32 / Sirius 34 without CAN
• EMS 3132 / EMS 3134 without CAN
• 1.9 2.2 and 2.5 dCi without CAN
• Delphi DDCR
Renault without CAN
• 1.9 dTi 1 plug
and
Renault without CAN – old ECUs • 1.9 dTi 2 plugs
• 1.9 diesel DCU3
• 2.8 TD
• 1 plug with 24C02 memory
• Volvo S40 and V40 – 1.9 TD Bosch ECU

Wiring colour codes

The LED behavior


- no jumpers – diagnostic mode - it flashes every second

- adjusting to the ECU – flashing 0,1 sec

- after adjusting it lights constantly and blinks every other second


2

Back to Main Page

Renault without CAN

In Universal Julie Emulator


solder jumpers 2+3+4+5

Renault without CAN old ECUs

In Universal Julie Emulator


solder jumper J5

SIRIUS 32 / SIRIUS 34 without CAN


EMS 3132 / EMS 3134
1.9 2.2 and 2.5 dCi without CAN
Delphi DDCR
1.9 dTi 1 plug
1.9 dTi 2 plugs
1.9 diesel DCU3
2.8 TD
1 plug with 24C02 memory
Volvo S40 and V40 – 1.9TD (Bosch 0 281 001 906 ECU)
3

Back to Main Page


Renault without CAN

SIRIUS 32 without CAN

Find 29F200 or 29F400 flash

In the addresses from 4000 to 7FFF, find


all values 64 C7 or 54 D7 or B4 5C
and change these values and two units
before them into FF FF FF FF

Repeat it in the whole map from


4000 to 7FFF !!!
4

Back to Main Page


Renault without CAN

Connecting emulator to ECU

Take power and GND for the emulator


from the capacitor

Connect Code signal after desoldering a


333 resistor

If there is A82C250 CAN transducer


on the plate in the ECU, then the
emulator will not work in this ECU!!!
5

Back to Main Page


Renault without CAN

SIRIUS 34

Tested on SIRIUS 34 ECUs

S118301104 A
S118301104 B
S118301211 B
S118301211 C
S118301212 B
S118301213 B
S118301213 C
S118301216 B

Find 29F200 or 29F400 flash

In the addresses from 4000 to 7FFF, find


all values 64 C7 or 54 D7 or B4 5C
and change these values and two units
before them into FF FF FF FF

Repeat it in the whole map from 4000 to


7FFF !!!
6

Back to Main Page

Connecting emulator to ECU


Renault without CAN

Take power for the emulator from the capacitor at the flash
In order to start the starter you need to join two pins of starter's relay!
7

Back to Main Page


Renault without CAN

EMS 3132

Find 29F200 or 29F400 flash

In the addresses from 4000 to 7FFF, find all values


64 C7 or 54 D7 or B4 5C
and change these values and two units before them
into FF FF FF FF

Repeat it in the whole map from 4000 to 7FFF !!!

Take power for the emulator from the capacitor at the flash.
8

Back to Main Page

Connect green wire as pictured after


unsoldering 333 resistor and connect it
to the point which leads to the processor.
9

Back to Main Page


Renault without CAN

EMS 3134

Tested on EMS 3134 ECUs

S118301120 B
S118301124 A

Find 29F400 flash

In the addresses from 4000 to 7FFF, find all values


64 C7 or 54 D7 or B4 5C
and change these values and two units before them
into FF FF FF FF

Repeat it in the whole map from 4000 to 7FFF !!!


10

Back to Main Page


Renault without CAN

Connect green wire as pictured to 88 pin and cut it off from wiring.
11

Back to Main Page


Renault without CAN

1.9 2.2 and 2.5 dCi without CAN

Also works with the following Volvo


cars:

Volvo S40/V40 1.9 dCi 2001


tested on Bosch 0 281 010 441, 5P08 EEPROM

EDC15 - old

EDC15 - new EDC15 - new v2


12

Back to Main Page


Renault without CAN

In 5P08C3 memory
in the addresses:
003E 003F 0040 0041
and
0044 0045 0046 0047
change these values into FF

If there are VIN number


in memory content
use Renault with CAN ver 1 program

In ECU, solder immo line (code) of


emulator to the point as pictured

Take power for the emulator from the


capacitor on the ECU plate
13

Back to Main Page


Renault without CAN

Unsolder 334 resistor

Turn on the ignition for 30 seconds,then turn it off for 30 seconds and repeat the procedure a
few times

For Volvo cars: Solder the starter relay pins together for the car to start.
14

Back to Main Page

DDCR
Renault without CAN

Car without tachometer

Replace 25080 content and connect emulator.

10 pin of processor is immo line as pictured, which must be raised.


15

Back to Main Page


Renault without CAN

Take power from the capacitor at the memory.


Code injectors and settings with Clip or Launch.

For ECU HOM8200334540:


Use Julie as Renault without CAN program. Solder jumpers 2+3+4+5
Tested on:
Suzuki Jimny 1.5 diesel 2004
Nissan Almera 1.5 diesel 2004

1.9 dTi 1 Plug

also works with the following Volvo cars:


Volvo S40/V40 1.9 dTi 1999
16

Back to Main Page


Renault without CAN

Connecting emulator to ECU

Connect the immo line of emulator to


pin 59 of ECU.

Connect GND and ACC to diode in the


ECU.

Bend pin 59 in ECU socket


17

Back to Main Page

1.9 dTi 2 plugs

In the addresses from 174 to 177 and


1B7 to 1BA
change these values into FF FF FF FF in
24C04 memory

Connecting emulator to ECU


18

Back to Main Page


Renault without CAN

Cut off pin 15 from wiring!!!

1.9 diesel DCU3

Renault Kangoo 1.9 Diesel 2001


19

Back to Main Page


Renault without CAN

In addresses from 02 to 05 and 82 to 85


change these values into 00 00 FF FF in
95080 memory

Connecting emulator to ECU

Pin 20 must be bent in socket or cut off from the car wiring.

Connecting emulator to ECU


20

Back to Main Page


Renault without CAN
21

Back to Main Page


Renault without CAN

2.8 TD
(Renault Mascott)

In addresses from 040 to 1FF change these values into FF in 24C16 memory

Connecting emulator to ECU


22

Back to Main Page


Renault without CAN

1 plug with 24C02 memory


(Renault Laguna)

Cut off pin 50 from ECU!!!

In addresses from 05A to 05F and


from 0F2 to 0F7 change these values
into FF in 24C02 memory
23

Back to Main Page


Renault without CAN

Volvo S40 and V40 – 1.9TD (Bosch 0 281 001 906 ECU)
MSA 15.5-5.40

In addresses from 03F to 041 and from


054 to 057
change these values into 00 00 FF FF in
24C02 memory
24

Back to Main Page

Warning!!!

Due to possible construction changes of cars, check signals with multimeter in the ECU plug.

All rights reserved.


Unauthorized copying, hiring, lending, public performance will be punished!

We state that we are the only authentic authors of this manual. We possess copyright of this
publication. Any trials of unauthorized copying, hiring, quoting prohibited!!! Both service and
advertisement constitute copyright and they are the subject to the protection in accordance with the
Act from 4th Feb. 1994 on Copyright and Related Laws (Statute Book no. 24 position 93) and
protection on the basis of the Act from 8th June 1993 on combating an unfair competition (Statute
Book no. 47 position 211)

www.carlabimmo.com

Last updated 19.09.2018

You might also like