Before your start
7106508248 REV5.0.2
Which mode do you need? Please refer to the table to choose a proper mode.
Scenarios Operation Modes
You want to transform your wired (Ethernet) network to a Access Point Mode
wireless one. (Default Mode)
Quick Installation Guide You are in a Wi-Fi dead-zone or a place with weak wireless
signal. You want to have a larger effective range of the
wireless signal throughout your home or office.
Repeater Mode
(Range Extender)
You want to link multiple local networks to the same network
using wireless connections where physical wires are
Bridge with AP Mode
inconvenient (when connecting networks in different office
buildings, for example).
You have a wired device with an Ethernet port and no wireless
capability, for example, a Smart TV, Media Player, or game Client Mode
console. You want to connect it to the internet wirelessly.
You want to connect your devices to different wireless
networks and become isolated by VLANs. Multi-SSID Mode
TL-WA901ND is used for demonstration in this guide.
Configure the Access Point
Access Point Mode (Default) Transforms your existing wired network to a wireless one.
Internet
TL-WA901ND’s SSID
Wired Router
B D C A
1. Connect the access point according to Step A to D in the diagram. 3. Launch a web browser and enter http://tplinkap.net. Then log in using admin
2. Power on the access point, wait until the Power ( ) and Wireless ( ) LEDs are lit (all lowercase) for both username and password.
and stable, and use the default SSID and Password printed on the label of the 4. Click Quick Setup, select Access Point mode and click Next. Follow the
access point to join its Wi-Fi network. step-by-step instructions to complete the configuration.
Note: You can surf the internet now. For your wireless network security, it is recommended to change the default SSID 5. Now, reconnect your wireless devices to the new Wi-Fi network.
(network name) and the password of your Wi-Fi network. To do so, perform the following steps.
Enjoy!
Repeater (Range Extender) Mode Extends the range of an existing Wi-Fi network.
Internet Host AP’s SSID Host AP’s SSID
B A
1. Connect the access point according to Step A and B in the diagram. 5. Relocate the access point to a suitable place. For details, please refer to FAQ
2. Power on the access point, wait until the Power ( ) and Wireless ( ) LEDs are lit > Q5.
and stable, and use the default SSID and Password printed on the label of the 6. Now, connect your wireless devices to the Wi-Fi network using the Host AP ’s
access point to join its Wi-Fi network. SSID and password.
3. Launch a web browser and enter http://tplinkap.net. Then log in using admin (all
lowercase) for both username and password.
Enjoy!
4. Click Quick Setup, select Repeater (Range Extender) mode and click Next. Follow
the step-by-step instructions to complete the configuration.
Bridge with AP Mode Combines two local networks via wireless connection.
Internet Host AP’s SSID TL-WA901ND’s SSID
ON/OFF POWER ETHERNET WPS/RESET
B A
1. Connect the access point according to Step A and B in the diagram. 5. Relocate the access point to a suitable place. For details, please refer to FAQ
2. Power on the access point, wait until the Power ( ) and Wireless ( ) LEDs are lit > Q5.
and stable, and use the default SSID and Password printed on the label of the 6. Now, connect your wireless devices to the Wi-Fi network using the access
access point to join its Wi-Fi network. point’s SSID and password.
3. Launch a web browser and enter http://tplinkap.net. Then log in using admin (all
lowercase) for both username and password. Enjoy!
4. Click Quick Setup, select Bridge with AP mode and click Next. Follow the
step-by-step instructions to complete the configuration.
Client Mode Connects your wired devices to a wireless network.
Internet Host AP’s SSID
B A C D
1. Connect the access point according to Step A to D in the diagram. 4. Click Quick Setup, select Client mode and click Next. Follow the
2. Power on the access point, wait until the Power ( ) and Wireless ( ) LEDs are lit step-by-step instructions to complete the configuration.
and stable, and use the default SSID and Password printed on the label of the 5. Now, your wired connected devices can surf the internet.
access point to join its Wi-Fi network.
3. Launch a web browser and enter http://tplinkap.net. Then log in using admin Enjoy!
(all lowercase) for both username and password.
Multi-SSID Mode Creates multiple wireless networks to provide different security and VLAN groups.
VLAN 1
Internet
TL-WA901ND’s SSID
Wired Router VLAN 2
B D C A
1. Connect the access point according to Step A to D in the diagram. 4. Click Quick Setup, then select Multi-SSID mode and click Next. Follow the
2. Power on the access point, wait until the Power ( ) and Wireless ( ) LEDs are lit step-by-step instructions to complete the configuration.
and stable, and use the default SSID and Password printed on the label of the 5. Now, connect your wireless devices to the different Wi-Fi networks isolated
access point to join its Wi-Fi network. by VLANs.
3. Launch a web browser and enter http://tplinkap.net. Then log in using admin (all
lowercase) for both username and password. Enjoy!
Power on via PoE Injector
Power the device with the included passive PoE injector when the access point is located far from a power outlet.
Note: The passive PoE injector supports a cable length up to 30 meters, but the value may vary due to the environment.
TL-WA901ND’s SSID
Internet
Wired Router Passive PoE Injector
or
Frequently Asked Questions (FAQ)
Q1. How do I restore the access point to its factory default settings? • Power off your host AP and enter http://tplinkap.net in the web • The Best Way is Halfway
With the access point powered on, use a pin to press and hold the browser to try again. Generally, the ideal location for a repeater is about halfway between
WPS/RESET button until the Power LED starts blinking, and then release your wireless router and your wireless clients and make sure that the
the button. Q3. How do I recover the access point’s web management password location you choose is within the range of the host router. If that is
or retrieve my Wi-Fi password? not possible, place it closer to your wireless router to ensure stable
• If you forget the password required to access the access point's performance.
web management page, you must restore the access point to its
factory default settings.
• If your forget your Wi-Fi password, but are able to log in to the web
management page, log in and go to Wireless > Wireless Security
to retrieve or reset your Wi-Fi password.
Q4. What should I do if my wireless network is not stable?
• Less Obstacles, Better Performance
This could be caused by interference. You can try the following
methods: Choose a location with less obstacles around that may block the
signal between the access point and the host network. An open
• Log in to the web management page. Go to Wireless > Wireless corridor or a spacious location is ideal.
Note: Resetting the access point will clear all previous configurations, Settings and change your wireless channel to a different one.
• Less Interference Provides More Stability
and the access point will reset to the default Access Point Mode. • Move the access point to a new location away from Bluetooth
Choose a location away from Bluetooth devices and other household
devices and other household electronics, such as cordless phones,
microwaves, and baby monitors to minimize signal interference. electronics, such as cordless phones, microwaves, and baby
Q2. What should I do if I cannot access the web management page?
monitors to minimize signal interference.
• If the computer has a static IP address, change its settings to obtain an
IP address automatically. Q5. What can I do to maximize my signal strength in Repeater/Bridge
Safety Information
mode?
• Verify that http://tplinkap.net or http://192.168.0.254 is correctly · Keep the device away from water, fire, humidity or hot environments.
When choosing a location to optimize wireless signal in Repeater/ · Do not attempt to disassemble, repair, or modify the device.
entered in the web browser.
Bridge mode, we recommend the following: · Do not use any other chargers than those recommended.
• Use another web browser and try again. · Do not use damaged charger or USB cable to charge the device.
• Reboot your access point and try again. · Do not use the device where wireless devices are not allowed.
· Adapter shall be installed near the equipment and shall be easily accessible.
For technical support, the user guide and other information, please visit https://www.tp-link.com/support ©2018 TP-Link
