1710-1880 / 1710-2170 MHz ANTENNA SOLUTIONS
WT6533-19-AA
WT6533-19-AAG
XX Pol | VET Panel | 65° / 33° | 18.0 / 20.0 dBi
FEATURES:
• Side-by-Side 65° and 33°, Dual Polarisation, 4 Connectors
• Independent Tilt on each band 0-10° / 0-10°
• MET and RET versions
• Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
Model Number Options: WT6533-19-AA Manual Electrical Tilt Antenna
WT6533-19-AAG Remote Electrical Tilt Antenna (3GPP/AISG2.0)
Access Ports Description (Connectors)
The antenna has 4 connectors located at its bottom face and marked with colour rings. See photo next page.
65° Horizontal Beamwidth ports 1710-1880 MHz WHITE rings 2 x 7-16 DIN Female Long Neck
33° Horizontal Beamwidth ports 1710-2170 MHz BLUE rings 2 x 7-16 DIN Female Long Neck
Electrical Characteristics 85° HBW (White) 33° HBW (Blue)
Frequency Band 1710-1880 MHz 1710-1880 MHz 1900-2170 MHz
Gain 15.9 dBd (18.0 dBi) 17.6 dBd (19.7 dBi) 17.9 dBd (20.0 dBi)
Input Impedance 50Ω 50Ω
VSWR <1.5 <1.5
Polarisation ±45° ±45°
Horizontal Beamwidth (-3 dB) 68° 37° 33°
Vertical Beamwidth (-3 dB) 5° 7° 6°
Electrical Downtilt Range 0-10° 0-10°
Isolation Between Ports >25 dB >25 dB
Isolation Between Bands 45 dB typ. 45 dB typ.
Upper Sidelobe Rejection
18 dB typ. 18 dB typ.
(20° sector above main beam)
Front to Back Ratio >30 dB >30 dB
Maximum Power (per port) 160 W 160 W
Intermodulation
< -110 dBm < -110 dBm
3rd order for 2 x 20 W carriers
Electrical Downtilt Control
Electrical downtilt can be controlled separately for each side of the antenna. The two tilt indicators are covered by a removable transparent
cap. See photo next page.
Manual Control: A coloured knob at the end of the tilt indicator allows change of the tilt without need for a tool. Knob colours are identical
to connector colours as defined above. To access the knob, the cap is removed by turning it counter-clockwise. It is re-installed by opposite
rotation.
Remote Control: The remote control of the electrical tilt is managed by a module (MDCU) totally inserted at the bottom of the antenna.
One single module controls individually the tilt of each band (no need of daisy chain cables between the bands). For RET control, the
transparent cap must be in place and locked. This module does not add any additional length at the bottom of the antenna. The tilt angle
indicator stays always visible and the antenna still has manual tilt control (manual override).
An antenna ordered as a RET version is delivered with the MDCU module fitted in the antenna and already configured and pre-
commissioned. The RET control is fully operational once the antenna is installed and no mandatory actions like calibration are needed.
RET Module Part Number
MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in WT6533-19-AAG)
(only one needed per antenna)
Environmental Characteristics
Operating Temperature Range -40° to +60° C (-40° to +140° F)
Environmental ETS 300 019
RoHS Compliant Yes
Quoted performance parameters are provided to offer typical or range values only and may vary as a result of normal manufacturing and operational conditions. Extreme operational
conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to product may be made without notice.
1 of 2 www.amphenol-antennas.com REV0511
ANTENNA SOLUTIONS
1710-1880 / 1710-2170 MHz
WT6533-19-AA
WT6533-19-AAG
XX Pol | VET Panel | 65° / 33° | 18.0 / 20.0 dBi
Mechanical Characteristics
Dimensions (Height x width x depth) 1942 x 364 x 152 mm 76.5 x 14.3 x 6.0 in
Weight Antenna alone: 25.0 kg 55.1 lbs
Mounting hardware: 5.6 kg 12.3 lbs
Shroud Outdoor plastic, Grey RAL7035
Wind Speed Operational 160 km/hr 100 mph
Wind Speed Survival 200 km/hr 125 mph
Wind load at 160 km/hr (100 mph) Frontal: 1065 N Frontal: 239 lbf
Optional MHA Tray
An optional MHA tray can be fixed at the back of the antenna to install two dual MHA units (and also power splitters if wished). Its weight is 2 kg. Please contact us.
Mounting Hardware
Delivery includes brackets for mounting on pole 48 to 115 mm and to allow 8 degree mechanical downtilt or by reversal 2 degree uptilt (8 degree maximum).
This set of brackets also includes a pan/swivel ‘single pin’ system to allow for mounting on a non-vertical pole with correction of lateral variation.
Antenna Bottom Dimensions (in mm)
364 152
1222
Location of the MDCU
for RET Control (see text)
1942
Tilt indicators covered by a transparent cap.
Manual adjustment is accessed by removing
the caps. Knob colour is same as connectors.
For RET control, the caps must be in place.
Installation
Do not install the antenna with the connectors
facing upward.
Holes to fit
MHA Mounting Tray
Quoted performance parameters are provided to offer typical or range values only and may vary as a result of normal manufacturing and operational conditions. Extreme operational
conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to product may be made without notice.
REV0511 www.amphenol-antennas.com 2 of 2
