Mon Jul 22 09:51:54 CDT 2019

Vehicle: 3HSDJAPT1CN082327
Detected Modules

Detected Serial
Configuration
Part Number
Address

Kernel
Family Module Data Link Serial
ESC ESC 33 Drivetrain J1939 38305130
3598755C2 8 242

Inferred Modules

Detected Serial
Configuration
Part Number
Address

Kernel
Family Module Data Link Serial
Rear HVAC 58 Body Builder J1939
Engine Controller 0 Drivetrain J1939
ABS Controller for Gen2 11 Drivetrain J1939
2010 Gauge Cluster 23 Drivetrain J1939
Secondary Instrument Cluster 167 Drivetrain J1939
Global Broadcast Messages, J1708, non−proprietary messages 0 Switch & Door Pod J1708
First 6−Pack Switch Module 15 Switch & Door Pod J1708
Front Passenger Door Module 64 Switch & Door Pod J1708
Driver Door Module (two−door or four−door) 130 Switch & Door Pod J1708

Page 1

Page 1 of 9
 Mon Jul 22 09:51:54 CDT 2019

Features: 3HSDJAPT1CN082327
Feature Description
0595AAC BC PROG, KEY STATE
0595AAD BC PROG, BRAKE SWITCH
0595AAE BC PROG, WINDSHIELD WIPER
0595AAG BC PROG, HEADLIGHTS W/DRL With Auto
0595AAH BC PROG, LIGHTS ON W/WIPERS
0595AAJ BC PROG, HEADLIGHT REMINDER
0595AAL BC PROG, TURN SIGNALS/BRAKE With Combined Stop and Turns
0595AAM BC PROG, PARK / MARKER LIGHTS
0595AAN BC PROG, MARKER INTERRUPT SWITCH Located in Steering Wheel
0595AAS BC PROG, INTERIOR DOME LIGHTS in Sleeper
0595AAT BC PROG, INTERIOR FLOOR LIGHTS in Sleeper
0595AAU BC PROG, HEATED MIRRORS Rocker Switch, Aftermarket Only
0595AAV BC PROG, HORN ELECTRIC
0595AAZ BC PROG, PARK BRAKE INDICATOR
0595ABA BC PROG, SEATBELT INDICATOR
0595ABB BC PROG, AIR PRESSURE GAUGES
0595ABC BC PROG, TRAILER LIGHTING
0595ABD BC PROG, FUEL TANK GAUGE Single Right Side
0595ABJ BC PROG, ENGINE TYPE MFG Cummins/ PSI
0595ABK BC PROG, ENGINE COOLANT TEMP
0595ABL BC PROG, ENGINE OIL PRESS GAUGE
0595ABM BC PROG, TACHOMETER 2500 RPM
0595ABN BC PROG, SPEEDOMETER
0595ABP BC PROG, VOLTMETER
0595ABR BC PROG, WORK LIGHT Push Button B
0595ABV BC PROG, ABS INDICATOR for Full Power Hydraulic OR Air Brake Systems, Not Including Trailer
0595ABW BC PROG, TRAILER ABS INDICATOR
0595ABX BC PROG, EXTERIOR LIGHT CHECK for ProStar
0595ABY BC PROG, POWER WINDOW/DOOR LOC With 2 Doors
0595ACA BC PROG, AIR SUSPENSION DUMP
0595ACC BC PROG, AXLE TEMP GAUGE Dual (SIC)
0595ACL BC PROG, ELECTRICAL LOAD CONTROL
0595ACN BC PROG, AIR HORN Analog Input
0595ACV BC PROG, ENGINE AIR MONITOR
0595ACZ BC PROG, POWER DIVIDER LOCK
0595ADA BC PROG, BRAKE APPL GAUGE IN SIC
0595ADM BC PROG, HVAC In Sleeper and Cab (Behr)
0595ADP BC PROG, CLUTCH SWITCH
0595ADR BC PROG, PRNDL No PRNDL, Manual Transmission
0595ADV BC PROG, PDL WARNING BUZZER
0595ADX BC PROG, MONITOR ENG OIL TEMP Through ECM
0595ADY BC PROG, TRANS OIL TEMP Through Body Controller
0595ANU BC PROG, ENGINE IDLE Increment/Decrement to allow idle adjust on Cummins or IBB Engines
0595ANW BC PROG, DIAGNOSTICS LOCATION Display in Gauge Cluster
0595AYJ BC PROG, CRUISE CONT STEER WH ON/OFF, With Diagnosable Switches
0595BBB BC PROG, ENGINE FAN OVERRIDE for Low Air Pressure, No Switch

Page 1

Page 2 of 9
 Mon Jul 22 09:51:54 CDT 2019

Features: 3HSDJAPT1CN082327
Feature Description
0595BBM BC PROG, ENGINE IDLE SHUTDOWN 2010 Indicator Light in Cluster Warning that Engine Ready to Shutdown
0595BJM BC PROG, IP CONFIGURATION for ProStar & LoneStar, for 2010 Cluster
0595BKD BC PROG, BODY CONTROLLER for Truck Body Controller #2
0595BKL BC PROG, ENGINE RETARDER for 2010; Located in Steering Wheel
0595BSC BC PROG, ENGINE PARAMETERS Cummins ISX

Page 2

Page 3 of 9
 Mon Jul 22 09:51:54 CDT 2019

Parameters: 3HSDJAPT1CN082327 ESC

Cfg. Value
Cfg.
ID Parameter Value Unit Description Unit
Autolock speed. The speed at which the vehicle doors will lock automatically (requires power
locks); Setting this parameter to zero will disable Auto Door Locks.
652 AutoLock_Speed 15 mph 6180 kph/256
Once the system pressure falls below the set point defined by this parameter, the engine−cooling
fan is no longer requested on by the system provided BC_RCD_Fan_ON_Timer has expired.
1927 BC_RCD_Pressure_Fan_Off 235 psig 2350 psig*10
Once the system pressure rises above the set point defined by this parameter, the engine−cooling
fan is requested on by the system.
1928 BC_RCD_Pressure_Fan_On 315 psig 3150 psig*10
Five−short
beeps
2366 Battery_Volt_Alarm_Ty_Gen_2 No_Units The type of alarm that will occur when the needle reaches a warning area on the gauge. 4 No_Units
1943 Battery_Voltage_Max_WL 15 V Maximum set point for battery voltage in−gauge warning light 300 V/20
1944 Battery_Voltage_Min_WL 12 V Minimum set point for battery voltage in−gauge warning light 240 V/20
2343 Brake_App_Max_WL 38020 psig Maximum set point for brake application in−gauge warning light 65535 kPa*4
2337 Brake_App_Min_WL 38020 psig Minimum set point for brake application in−gauge warning light 65535 kPa*4
Automatic
Inflation of the
suspension
using
Suspension_
Dump_
Request is
inactive

This parameter when set will allow for the suspension to raise when the Diamond Logic
Suspension_Dump_Request signal becomes inactive.
2529 Raise_Suspension_OK No_Units 0 No_Units
2395 Dome_Light_Wait_Time 15 s Use this parameter to set the delay to onset of Theater Dimming. 1500 timercounts
1896 Dome_Light_Hi_Current 10 A Dome Light High Current Detection Level (Amps) 10000 mA
1895 Dome_Light_Lo_Current 0 A Dome Light Low Current Detection Level (Amps) 0 mA
1897 Dome_Light_OC_Current 0 A Dome Light Open Circuit Detection Level (Amps) 0 mA
1902 Elec_City_Horn_Hi_Current 12 A Electric City Horn High Current Detection Level (Amps) 12000 mA
1901 Elec_City_Horn_Lo_Current 0.5 A Electric City Horn Low Current Detection Level (Amps) 500 mA
1903 Elec_City_Horn_OC_Current 0.5 A Electric City Horn Open Circuit Detection Level (Amps) 500 mA
One−time Five−
short−beeps
2347 Eng_Oil_Press_Alrm_Ty_Param No_Units A list of alarm types codes to teach/reteach the cluster. 4 No_Units
2376 Eng_Oil_Press_Max_WL 38020 psig Maximum set point for engine oil pressure in−gauge warning light 65535 kPa*4
1948 Eng_Oil_Press_Min_WL 6.9618 psig Minimum set point for engine oil pressure in−gauge warning light 12 kPa*4
One−time Five−
short−beeps
2354 Eng_Oil_Temp_Alrm_Ty_Param No_Units A list of alarm types codes to teach/reteach the cluster. 4 No_Units
2274 Eng_Oil_Temp_Max_WL 251.99 F Maximum set point for engine oil temperature in−gauge warning light 12647 K/32
2291 Eng_Oil_Temp_Min_WL 3226.9 F Minimum set point for engine oil temperature in−gauge warning light 65535 K/32
2351 Eng_Speed_Alrm_Ty_Param No Alarm No_Units The Tachometer alarm that will occur when the needle reaches a warning area on the gauge. 0 No_Units
2323 Eng_Speed_Max_WL 8191.9 RPM Maximum set point for engine speed in−gauge warning light 65535 RPM/8
2326 Eng_Speed_Min_WL 8191.9 RPM Minimum set point for engine speed in−gauge warning light 65535 RPM/8
Five−short
beeps
2358 Eng_Watr_Temp_Alrm_Ty_Param No_Units A list of alarm types codes to teach/reteach the cluster. 4 No_Units
2292 Eng_Watr_Temp_Max_WL 240.8 F Maximum set point for engine coolant temperature in−gauge warning light 156 C+40

Page 1

Page 4 of 9
 Mon Jul 22 09:51:54 CDT 2019

Parameters: 3HSDJAPT1CN082327 ESC

Cfg. Value
Cfg.
ID Parameter Value Unit Description Unit
2293 Eng_Watr_Temp_Min_WL 117920 F Minimum set point for engine coolant temperature in−gauge warning light 65535 C+40
Exterior_Lamp_Check_Enabled_
Time
2318 10 min This parameter determines how long the Gen2 ELC will be active 60000 timercounts
2271 Exterior_Lamp_Interval_Time 2 s Time that each step of exterior lamp check will run before moving on 200 timercounts
Use this parameter to enable exterior lamp reminder. A value of 1 will result in an audible warning
when the vehicle is off and the lights are on. A value of 0 is used to deactivate the audible
warning.
2179 Exterior_Lamp_Warn On/Off 1 On/Off
2305 Fuel_Level_Max_WL_Gen2 26214 percent Maximum set point for fuel level in−gauge warning light 65535 percent/2.5
1958 Fuel_Level_Min_WL 12.8 percent Minimum set point for fuel level in−gauge warning light 32 percent/2.5
Fwd_RR_Axle_Temp_Alarm_Ty_ Five−short
Param beeps
2364 No_Units The type of alarm that will occur when the needle reaches a warning area on the gauge. 4 No_Units
2294 Fwd_RR_Axle_Temp_Max_WL 240.8 F Maximum set point for forward rear axle temperature in−gauge warning light 156 C+40
2295 Fwd_RR_Axle_Temp_Min_WL 117920 F Minimum set point for forward rear axle temperature in−gauge warning light 65535 C+40
Five−short
beeps
510 Fuel_Level_Alrm_Ty_Param No_Units The type of alarm that will occur when the needle reaches a warning area on the gauge. 4 No_Units
2348 LH_Brake_App_Alrm_Ty_Param No Alarm No_Units The type of alarm that will occur when the needle reaches a warning area on the gauge. 0 No_Units
Deactivate/activate headlights on with wipers. A value of 1 is used to activate and a value of 0 is
used to deactivate headlights on with wipers.
317 Lights_on_with_Wipers On/Off 1 On/Off
1911 LT_FT_Turn_Hi_Current 10 A Left Front Turn Signal High Current Detection Level (Amps) 10000 mA
1910 LT_FT_Turn_Lo_Current 0.5 A Left Front Turn Signal Low Current Detection Level (Amps) 500 mA
1912 LT_FT_Turn_OC_Current 0.5 A Left Front Turn Signal Open Circuit Detection Level (Amps) 500 mA
1905 LT_RR_Turn_Hi_Current 10 A Left Rear Turn Signal High Current Detection Level (Amps) 10000 mA
1904 LT_RR_Turn_Lo_Current 0 A Left Rear Turn Signal Low Current Detection Level (Amps) 0 mA
1906 LT_RR_Turn_OC_Current 0 A Left Rear Turn Signal Open Circuit Detection Level (Amps) 0 mA
2276 Left_Highbeam_Hi_Current 10 A High Beam Headlight High Current Detection Level (Amps) 10000 mA
2281 Left_Highbeam_Lo_Current 0.5 A High Beam Headlight Low Current Detection Level (Amps) 500 mA
2280 Left_Highbeam_OC_Current 0.5 A High Beam Headlight Open Circuit Detection Level (Amps) 500 mA
2285 Left_Lowbeam_Hi_Current 10 A Low Beam Headlight High Current Detection Level (Amps) 10000 mA
2286 Left_Lowbeam_Lo_Current 0.5 A Low Beam Headlight Low Current Detection Level (Amps) 500 mA
2287 Left_Lowbeam_OC_Current 0.5 A Low Beam Headlight Open Circuit Detection Level (Amps) 500 mA
2302 Left_Mirror_Heat_Hi_Current 10 A Mirror Heat High Current Detection Level (Amps) 10000 mA
2301 Left_Mirror_Heat_Lo_Current 0.5 A Mirror Heat Low Current Detection Level (Amps) 500 mA
2300 Left_Mirror_Heat_OC_Current 0.5 A Mirror Heat Open Circuit Detection Level (Amps) 500 mA
Load Shed
level 1
2360 Load_Shed_Mirror_Heat_Level No_Units The list of the shed levels are recorded below 1 No_Units
Each increment of 1 is equal to 5 minutes. A value of 1 through 12 allows the mirror heat feature
to time out 5 minutes to 60 minutes, a value of 0 leaves mirror heat on indefinitly.
338 Mirror_Heat_Timeout_Enable 0 No_Units 0 No_Units
Sets the vehicle speed at which the PDL switch indicator will begin to flash while the PDL is
locked. The flashing is accompanied by a 5 short beep audible alarm.
2383 PDL_Warning_Spd 99.999 mph 41199 kph/256

Page 2

Page 5 of 9
 Mon Jul 22 09:51:54 CDT 2019

Parameters: 3HSDJAPT1CN082327 ESC

Cfg. Value
Cfg.
ID Parameter Value Unit Description Unit
Use this parameter to enable Park Brake Reminder. A value of 1 will result in an audible warning
when the vehicle is being driven with the park brake set. A value of 0 is used to deactivate the
audible warning.
2349 Park_Brake_Reminder On/Off 0 On/Off
2223 Park_Light_Hi_Current 10 A Park & ID Lights High Current Detection Level (Amps) 10000 mA
2225 Park_Light_Lo_Current 0.5 A Park & ID Lights Low Current Detection Level (Amps) 500 mA
2221 Park_Light_OC_Current 0.5 A Park & ID Lights Open Circuit Detection Level (Amps) 500 mA
2315 Prim_Air_Press_Max_WL 76040 psig Maximum threshold for primary air pressure in−gauge warning light 65535 kPa*8
2316 Prim_Air_Press_Min_WL 69.618 psig Minimum threshold for primary air pressure in−gauge warning light 60 kPa*8
RCD_AC_Comp_Clutch_Hi_
Current
1893 10 A RCD Air Conditioning Compressor Clutch High Current Detection Level (Amps) 10000 mA
RCD_AC_Comp_Clutch_Lo_
Current
1892 0.5 A RCD Air Conditioning Compressor Clutch Low Current Detection Level (Amps) 500 mA
RCD_AC_Comp_Clutch_OC_
Current
1894 0.5 A RCD Air Conditioning Compressor Clutch Open Circuit Detection Level (Amps) 500 mA
1914 RT_FT_Turn_Hi_Current 10 A Right Front Turn Signal High Current Detection Level (Amps) 10000 mA
1913 RT_FT_Turn_Lo_Current 0.5 A Right Front Turn Signal Low Current Detection Level (Amps) 500 mA
1915 RT_FT_Turn_OC_Current 0.5 A Right Front Turn Signal Open Circuit Detection Level (Amps) 500 mA
1908 RT_RR_Turn_Hi_Current 10 A Right Rear Turn Signal High Current Detection Level (Amps) 10000 mA
1907 RT_RR_Turn_Lo_Current 0 A Right Rear Turn Signal Low Current Detection Level (Amps) 0 mA
1909 RT_RR_Turn_OC_Current 0 A Right Rear Turn Signal Open Circuit Detection Level (Amps) 0 mA
Rear_RR_Axle_Temp_Alarm_Ty_ Five−short
Param beeps
2365 No_Units The type of alarm that will occur when the needle reaches a warning area on the gauge. 4 No_Units
2296 Rear_RR_Axle_Temp_Max_WL 240.8 F Maximum set point for rear rear axle temperature in−gauge warning light 156 C+40
2303 Rear_RR_Axle_Temp_Min_WL 117920 F Minimum set point for rear rear axle temperature in−gauge warning light 65535 C+40
2282 Right_Highbeam_Hi_Current 10 A High Beam Headlight High Current Detection Level (Amps) 10000 mA
2283 Right_Highbeam_Lo_Current 0.5 A High Beam Headlight Low Current Detection Level (Amps) 500 mA
2284 Right_Highbeam_OC_Current 0.5 A High Beam Headlight Open Circuit Detection Level (Amps) 500 mA
2288 Right_Lowbeam_Hi_Current 10 A Low Beam Headlight High Current Detection Level (Amps) 10000 mA
2289 Right_Lowbeam_Lo_Current 0.5 A Low Beam Headlight Low Current Detection Level (Amps) 500 mA
2290 Right_Lowbeam_OC_Current 0.5 A Low Beam Headlight Open Circuit Detection Level (Amps) 500 mA
2299 Right_Mirror_Heat_Hi_Current 10 A Mirror Heat High Current Detection Level (Amps) 10000 mA
2298 Right_Mirror_Heat_Lo_Current 0.5 A Mirror Heat Low Current Detection Level (Amps) 500 mA
2297 Right_Mirror_Heat_OC_Current 0.5 A Mirror Heat Open Circuit Detection Level (Amps) 500 mA
2329 Sec_Air_Press_Max_WL 76040 psig The Display UOM has changed for LH from kpa*4 to kpa*8 65535 kPa*8
2331 Sec_Air_Press_Min_WL 69.618 psig The config UOM has changed from kPa*4 to kPa*8 60 kPa*8
Enable/disable stoplights override hazard lights. A value of 1 enables and a value of 0 disables the
feature.
2317 Stop_Override_Hazard_Enabled On/Off 1 On/Off

Page 3

Page 6 of 9
 Mon Jul 22 09:51:54 CDT 2019

Parameters: 3HSDJAPT1CN082327 ESC

Cfg. Value
Cfg.
ID Parameter Value Unit Description Unit
This parameter selects when the suspension may be dumped in each ignition key state. 0 = enable
dump when the key is in ACCESSORY or IGNITION position; 1 = enable dump when the key is
in the IGNITION position only; 2 = enable dump when the key is in the ACCESSORY, OFF or
IGNITION position. This parameter only applies to the Suspension_Dump_Request Signal. The
Default. Dump suspension dump rocker switch in the cab allows suspension dump control any time the key is in
in key=RUN the ACCESSORY or IGNITION position only.
only.
2472 Susp_Dump_KeyState_Param No_Units 1 No_Units
One−time Five−
short−beeps
2356 Trans_Oil_Temp_Alrm_Ty_Param No_Units A list of alarm types codes to teach/reteach the cluster. 4 No_Units
2272 Trans_Oil_Temp_Max_WL 259.98 F Maximum set point for transmission oil temperature in−gauge warning light 12789 K/32
2273 Trans_Oil_Temp_Min_WL 3226.9 F Minimum set point for transmission oil temperature in−gauge warning light 65535 K/32
2350 Vehicle_Speed_Alrm_Ty_Param No Alarm No_Units The Speedometer alarm that will occur when the needle reaches a warning area on the gauge. 0 No_Units
2332 Vehicle_Speed_Max_WL 159.07 mph Maximum Threshold for vehicle speed in−gauge warning light 65535 kph/256
2328 Vehicle_Speed_Min_WL 159.07 mph Minimum Threshold for vehicle speed in−gauge warning light 65535 kph/256
1887 Wipers_Hi_Current 15 A Winshield Wipers High Current Detection Level (Amps) 15000 mA
1886 Wipers_Lo_Current 0 A Windshield Wipers Low Current Detection Level (Amps) 0 mA
1888 Wipers_OC_Current 0 A Windshield Wipers Open Circuit Detection Level (Amps) 0 mA
1899 Work_Light_Hi_Current 10 A Work Light High Current Detection Level (Amps) 10000 mA
1898 Work_Light_Lo_Current 0.5 A Work Light Low Current Detection Level(Amps) 500 mA
1900 Work_Light_OC_Current 0.5 A Work Light Open Circuit Detection Level (Amps) 500 mA
This parameter is required to turn off the work light if the vehicle’s speed is greater than the work
light off speed parameter
2568 Work_Light_Off_Speed 89.999 mph 37079 kph/256
This parameter sets the amount of time that the work light will remain on after the ignition is
turned to off.
640 Work_Light_Timeout_Enable 12 min*10 12 min*10

Page 4

Page 7 of 9
Connectors: 3HSDJAPT1CN082327
Mon Jul 22 09:51:54 CDT 2019
ESC Power_Feed (ESC J6) Mating View Shown 1604 (ESC J2) Mating View Shown

J6 [1] Power_Supply_1_Signal
(Power_Feed) Right_Highbeam_Cmd [K] [E] Cab Ground
Power
Dome_Light [J] [D]
J4
(1601) Right_Lowbeam_Cmd [H] [C] Left_Highbeam_Cmd
Cab J1
(1603) Park_Lights [G] [B] Left_Lowbeam_Cmd
Hood
[F] [A] Wipers_Output_from_fuse_circuit
J2
(1604)
Chassis

J3
(1600)
Inside

J5
(1602)
Engine

1603 (ESC J1) Mating View Shown 1602 (ESC J5) Mating View Shown

[F1] [E1] Switch Datalink −

Right_Turn_Signal_Blink [A] [G] Work_Light
Drive Train J1939 Datalink −[F2] [E2] Switch Datalink +
(Click on a connector
to Left_Turn_Signal_Blink
see the pin usage.) [B] [H] Left_Mirror_Heat_Cmd Drive Train J1939 Datalink + [F3] [E3] Zero Volt Reference
Body Builder J1939 Datalink Shield [F4] [E4] Switched_5V_Sense_Signal
AC_Clutch [C] [J]
Body Builder J1939 Datalink −[F5] [E5] Zero Volt Reference

LT_RR_Turn_Cmd [D] [K] Body Builder J1939 Datalink + [F6] [E6] Switched_5V_Sense_Signal
[F7] [E7] Zero Volt Reference
City_Horn [E] [L] Right_Mirror_Heat_Cmd
Comp_Brake_Switch_Input [F8] [E8] Switched_5V_Sense_Signal

[F] [M] RT_RR_Turn_Cmd Engine_Air_Intake [F9] [E9]

[F10] [E10]
[F11] [E11] Headlight_Enable_Signal

[F12] [E12] Air_Horn

[F13] [E13]
[F14] [E14] Brake_Switch_Digital_Input, Brake_Analog_Switch_Signal

[F15] [E15] Brake_Switch_Digital_Input, Brake_Analog_Switch_Signal

[F16] [E16] Chassis Ground

1601 (ESC J4) Mating View Shown 1600 (ESC J3) Mating View Shown

[F1] [E1] Steering_Wheel_Switches_Signal [B1] [A1] Accessory_Signal_Input

Sleeper_Cab_Dome_Light [F2] [E2] Primary_Air_Pressure [B2] [A2] Front_HVAC_AC_Req
[F3] [E3] Secondary_Air_Pressure [B3] [A3] RCD_HVAC_Ctrl_Head_Diag_Signal
[F4] [E4] Clutch_Switch_Signal [B4] [A4] Highbeam_Signal
[F5] [E5] Floor_Search_Lights BC_RCD_Temp_In_Cond_Signal [B5] [A5] Elec_City_Horn_SW_Signal
Load_Shed_Power_Off_RD_Cmd [F6] [E6] Wiper_High_Speed_Cmd [B6] [A6] Right_Turn_Signal_Switch
Load_Shed_Power_On_RD_Cmd [F7] [E7] Wiper_Low_Speed_Cmd Trans_Oil_Temp_Signal [B7] [A7] Left_Turn_Signal_Switch
PDL_Lock_Solenoid_Cmd [F8] [E8] Right_Fuel_Sensor_Signal [B8] [A8] Low_Washer_Fluid_WL_Signal
[F9] [E9] [B9] [A9] Wiper_0_Signal
Susp_Dump_Solenoid_A_Cmd [F10] [E10] Tail Light signal for LH trailers Frwd_RR_Axle_Oil_Temperature [B10] [A10] Wiper_1_Signal
[F11] [E11] Rear_RR_Axle_Oil_Temp_Signal [B11] [A11] Wiper_2_Signal

[F12] [E12] Susp_Dump_Solenoid_B_Cmd AC_High_Side_Pressure [B12] [A12] Park_Brake_Switch_Signal

Trailer Left Turn Light [F13] [E13] BC_RCD_Temp_Out_Cond_Signal [B13] [A13] Door_Switch
LH Trailer Marker light signal [F14] [E14] Service_Brake_App_Air_Sensor_Signal [B14] [A14] Flash_To_Pass_Signal

LH Trailer Brake Signal [F15] [E15] Trailer Right Turn Light Front_AC_Blower_Speed [B15] [A15] Washer_Pump_Signal
[F16] [E16] Cruise_Switch_Raw_Signal [B16] [A16] Ignition_Signal_Input

Page 8 of 9
Instrument Panel: 3HSDJAPT1CN082327
Mon Jul 22 09:51:54 CDT 2019

On UP UP Eng Lock Dump Blank Blank Blank Blank Blank Blank

3
SLPR SLPR 2
TEMP FAN
Mir DOWN DOWN 1 PDL Susp
Heat Brake

Blank Blank Blank Blank Blank Blank

Cab Slpr
AUTO
Dome Dome
Door

Off Floor
Light
WORK

Page 9 of 9