126.
03
Tile-Clad® HS
Catalyzed Epoxy
B62-100 Series
CHARACTERISTICS COMPLIANCE SPECIFICATIONS
TILE-CLAD HIGH SOLIDS is a two-component, As of 02/17/2020, Complies with: Steel:
epoxy-polyamide coating for use in industrial OTC No
OTC Phase II No 1 coat Pro Industrial Pro-Cryl Primer
maintenance environments and high SCAQMD No or Kem Bonds HS
performance architectural applications. CARB No 2 coats Tile-Clad HS Catalyzed Epoxy
Features: CARB SCM 2007 No
• Chemical resistant Canada No
LEED® v4 & v4.1 Emissions No Aluminum:
• Impact and abrasion resistance LEED® v4 & v4.1 V.O.C. No 1 coat DTM Wash Primer
• Suitable for use in USDA inspected facilities EPD-NSF® Certified No 2 coats Tile-Clad HS Catalyzed Epoxy
For use on properly prepared: MIR-Product Lens Certified No
Steel, Galvanized and Aluminum, Concrete and MPI Yes Galvanizing:
Masonry and Wood APPLICATION 2 coats Tile-Clad HS Catalyzed Epoxy
Temperature:
Recommended for use in: minimum 55°F Concrete Block (CMU):
Power plants, Laboratories and lavatories, maximum 110°F 1 coat Pro Industrial Heavy Duty Blockfiller
Institutional kitchens, Storage Tanks, Piping, air, surface, and material
Structural Steel Manufacturing Facilities and 2 coats Tile-Clad HS Catalyzed Epoxy
Kitchens At least 5°F above dew point
Relative humidity: 85% maximum Concrete and Masonry Smooth:
Finish: Gloss and Eg-Shel The following is a guide. Changes in pressures and tip sizes may be
2 coats Tile-Clad HS Catalyzed Epoxy
Hardeners needed for proper spray characteristics. Always purge spray equipment
before use with listed reducer. Any reduction must be compatible with the
Color: Most colors existing environmental and application conditions. Drywall:
Recommended Spreading Rate per coat: Reducer: No reduction in restricted area 1 coat ProMar 200 Zero V.O.C. Primer
As mixed B62WZ0111/B60VZ0070 Reducer#54,R7K54,R6K25 2 coats Tile-Clad HS Catalyzed Epoxy
Wet mils: 4.0-7.0 Airless Spray:
Pressure 2400 p.s.i. Wood, interior including floors:
Dry mils: 2.1-3.6 Hose 3/8 inch I.D. 2 coats Tile-Clad HS Catalyzed Epoxy
Coverage: sq.ft. per gallon 231-397 Tip .019 inch
Theoretical Coverage: 834 Filter 60 mesh
sq. ft. per gallon @1 mil dry Reduction As needed up to 10% by volume
The systems listed above are representative of the
Approximate spreading rates are calculated on volume Brush Nylon-polyester, product’s use, other systems may be appropriate.
solids and do not include any application loss. Note: Brush natural bristle
or roll application may require multiple coats to achieve Roller Cover 1/4-3/8 inch woven
maximum film thickness and uniformity of appearance. solvent resistant core
Drying Schedule @ 4.0 mils wet, @ 50% RH: If specific application equipment is listed above,
Drying, and recoat times are temperature, humidity, and equivalent equipment may be substituted.
film thickness dependent.
@55°F @77°F @110°F Apply paint at the recommended film thickness and
To touch: 3 hrs. 1 hr. 20 min. spreading rate as indicated. Application of coating
Tack free 6 hrs. 2 hrs. 30 min. above maximum or below minimum recommended
Minimum recoat: 6 hrs. 2 hrs. 30 min. spreading rate may adversely affect coating
performance. Spreading rates are calculated on
Maximum recoat:* 30 days 30 days 30 days volume solids and do not include an application loss
To stack 18 hrs. 16 hrs. 3 hrs. factor due to surface profile, roughness, or porosity
To cure 21 days 14 days 7 days of the surface, skill, and technique of the applicator,
Pot Life 4 hrs. 4 hrs. 2 hrs. method of application, various surface irregularities,
material lost during mixing, spillage, over thinning,
Sweat-In-Time 1 hr 30 min. 10 min. climatic conditions, and excessive film build.
Mix Ratio: 2 components, premeasured 1:1
Mix contents of each component thoroughly with low
*If maximum recoat time is exceeded, abrade surface before recoating.
speed power agitation. Make certain no pigment
Five minutes minimum mixing on a mechanical shaker is required for remains on the bottom of the can. Then combine one
complete mixing of color. part by volume of Part A with one part by volume of
Tinting with: Maxitoner or BAC into Part A Part B. Thoroughly agitate the mixture with power
Base oz. per gallon Strength agitation. Allow the material to sweat-in as indicated.
Extra White 0-10 200% Re-stir before using. If reducer solvent is used, add
Deep Base 4-24 200% only after both components have been thoroughly
Ultradeep Base 10-22 200% mixed, after sweat-in. Do not apply the material
beyond recommended pot life. Do not mix previously
Extra White B62WZ0111/B60VZ0070 catalyzed material with new.
(may vary by color)
V.O.C. (less exempt solvents): As mixed Stripe coat crevices, welds, and sharp angles to
420 grams per litre; 3.50 lbs. per gallon prevent early failure in these areas. When using spray
As per 40 CFR 59.406 application, use a 50% overlap with each pass of the
Volume Solids: 52 ± 2% gun to avoid holidays, bare areas, and pinholes. If
Weight Solids: 66 ± 2% necessary, cross spray at a right angle. No painting
should be done immediately after a rain or during
Weight per Gallon: 10.35 lb foggy weather.
Flash Point: 83°F TCC
Vehicle Type: Polamide Epoxy All epoxies will chalk and fade when un-topcoated in
Shelf Life: Part A and B: 36 months exterior environments. Apply appropriate topcoat if
aesthetics are require
02/2020 www.sherwin-williams.com continued on back
Tile-Clad® HS
Catalyzed Epoxy
SURFACE PREPARATION SURFACE PREPARATION SAFETY PRECAUTIONS
WARNING! Removal of old paint by sanding, Mildew- Prior to attempting to remove mildew, it Before using, carefully read CAUTIONS on
scraping or other means may generate dust or fumes is always recommended to test any cleaner on a label.
that contain lead. Exposure to lead dust or fumes may small, inconspicuous area prior to use. Bleach and Refer to the Safety Data Sheets (SDS) before
cause brain damage or other adverse health effects, bleaching type cleaners may damage or discolor use.
especially in children or pregnant women. Controlling existing paint films. Bleach alternative cleaning
exposure to lead or other hazardous substances solutions may be advised. FOR PROFESSIONAL USE ONLY.
requires the use of proper protective equipment, Mildew may be removed before painting by washing Published technical data and instructions are
such as a properly fitted respirator (NIOSH approved) with a solution of 1 part liquid bleach and 3 parts subject to change without notice. Contact your
and proper containment and cleanup. For more water. Apply the solution and scrub the mildewed Sherwin-Williams representative for additional
information, call the National Lead Information Center area. Allow the solution to remain on the surface for technical data and instructions.
at 1-800-424-LEAD (in US) or contact your local 10 minutes. Rinse thoroughly with water and allow
health authority. the surface to dry before painting. Wear protective
Remove all surface contamination by washing with eyewear, waterproof gloves, and protective clothing.
an appropriate cleaner, rinse thoroughly and allow
to dry. Existing peeled or checked paint should be
Quickly wash off any of the mixture that comes in
contact with your skin. Do not add detergents or
CLEANUP INFORMATION
scraped and sanded to a sound surface. Glossy ammonia to the bleach/water solution. Clean tools, spills and spatters immediately with
surfaces should be sanded dull. Stains from water, compliant cleanup solvent. After cleaning, flush
smoke, ink, pencil, grease, etc. should be sealed with PERFORMANCE spray equipment with compliant cleanup solvent
the appropriate primer/sealer. Recognize that any to prevent rusting of the equipment. Follow
Extra White B62WZ0111/B60VZ0070
surface preparation short of total removal of the old manufacturer’s safety recommendations when
coating may compromise the service length of the System Tested: (unless otherwise indicated)
system. Substrate: Steel using solvents.
Surface Preparation: SSPC-SP6
Iron & Steel - Minimum surface preparation is Hand Finish: 1coat Tile-Clad HS Epoxy @ 3.0 mils D.F.T.
Tool Clean per SSPC-SP2. Remove all oil and grease HOTW 02/17/2020 B62WZ111/B60VZ70 30 420
from surface by Solvent Cleaning per SSPC-SP1. For Adhesion1:
Method: ASTM D4541 HOTW 02/17/2020 B62WZ113/B60VZ70 17 419
better performance, use Commercial Blast Cleaning HOTW 02/17/2020 B62TZ104/B60VZ70 20 419
per SSPC-SP6/NACE 3, blast clean all surfaces Result: 400 p.s.i. minimum.
using a sharp, angular abrasive for optimum surface Abrasion Resistance : 1
profile (2 mils). Remove all weld spatter and round Method: ASTM D2486
all sharp edges by grinding to a minimum of ¼ inch Result: greater than 500 cycles
radius. Prime any bare steel within 8 hours or before
flash rusting occurs. Primer required.
Sag Test2:
Method: based on ASTM D4400
Aluminum - Remove all oil, grease, dirt, oxide and Result: 12 mils minimum
other foreign material per SSPC-SP1. Prime the area
the same day as cleaned. Dry Heat Resistance:
Drywall - Must be clean and dry. All nail heads must Method: ASTM D2485
be set and spackled. Joints must be taped and Result: 200°F
covered with a joint compound. Spackled nail heads Impact Resitance : 1
and tape joints must be sanded smooth and all dust Method: ASTM D2794
removed prior to painting. Primer required. Result: 53 inch per lb minimum
Galvanizing - Allow to weather a minimum of six Fineness of Grind2:
months prior to coating. Solvent Clean per SSPC- Method: Hegman
SP1. When weathering is not possible, or the surface Result: 5.5 Hegman minimum
has been treated with chromates or silicates, first
Solvent Clean per SSPC-SP1 and apply a test
patch. Allow paint to dry at least one week before Chemical Resistance Rating: 7 day ambient cure
testing adhesion. If adhesion is poor, brush blasting B62WZ0111/B60VZ0070
per SSPC-SP16 is necessary to remove these (1 hour direct exposure to dry film Incidental contact)
treatments. Rusty galvanizing requires a minimum of 15% Hydrochloric Acid- Pass
Hand Tool Cleaning per SSPC-SP2, prime the area 5% Sulfuric Acid-Pass
the same day as cleaned. 20% Sodium Hydroxide-Pass
Concrete Block - Surface should be thoroughly Aliphatic Hydrocarbon Solvent-Pass
clean and dry. Air, material and surface temperatures Methyl Alcohol-Pass
must be at least 55°F before filling. Use Pro Industrial Motor Oil (10 W 30)-Pass
Heavy Duty Block Filler. The filler must be thoroughly Vegetable Oil-Pass
dry before topcoating. 1
1 coat Dura-Plate 235, 1 coat Tile-Clad Epoxy
Masonry - All masonry must be free of dirt, oil,
grease, loose paint, mortar, masonry dust, etc. Clean 2
Standard test based on Certificate of Analysis
per SSPC-SP13-Nace 6- ICRI No. 310.2R, CSP
1-3. Poured, troweled, or tilt-up concrete, plaster, Quik-Kick Epoxy Accelerator is acceptable for
mortar, etc. must be thoroughly cured at least 30 use.
days at 75°F. Form release compounds and curing
membranes must be removed by brush blasting. Excessive film build, poor ventilation, and cool
Brick must be allowed to weather for one year prior temperatures may cause solvent entrapment and
to surface preparation and painting. Prime the area premature coating failure. Insufficient ventilation,
the same day as cleaned. Weathered masonry and incomplete mixing, miscatalyzation, moisture and
soft or porous cement board must be brush blasted external heaters may cause premature yellowing.
or power tool cleaned to remove loosely adhering
contamination and to get to a hard, firm surface.
Wood - Surface must be clean, dry, and sound. Paint
as soon as possible. No painting should be done
immediately after a rain or during foggy weather.
Knots and pitch streaks must be scraped, sanded
and spot primed. All nail holes or small openings
must be properly caulked. Sand to remove any loose
or deteriorated surface wood and to obtain a proper
surface profile. Self priming.
The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of The Sherwin-Williams Company. Such information
and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Consult your Sherwin-Williams representative or visit
www.paintdocs.com to obtain the most current version of the PDS and/or an SDS.
