K itchen F aucets
Installation Guide
and Users Manual
ZLINE created a wide range of faucet solutions delivering comfortable
elegance and undeniable quality down to the smallest detail. Brass
housing allows ZLINE faucets to be durable and provides sophistication.
It’s what’s on the inside that counts.
Behind the scenes, ZLINE’s main focus is improving water efficiency.
The faucets are manufactured with carefully hand selected materials
that undergo over 50,000 unit tests, well over the industry standard for
certification of 15,000 tests. 1.8 gal/min provides the perfect aerated
water pressure — saving water, energy, and time at the best price point in
the industry.
TABLE OF CONTENTS
SAFETY INSTRUCTIONS 1
Prior to Installation
Safety Tips
Installation Preparation
Care and Maintenance
Notes
SPRING FAUCETS 3
Parts
Tools
Models:
FSNZ (Apollo Series)
FSTB (Sierra Series)
12-0140 (Van Gogh Series)
Assembly
PULL DOWN FAUCETS 9
Parts
Tools
Models:
FPBC (Castor Series)
11-0129 (Shakespeare Series)
FPBL (Edison Series)
FPTF (Gemini Series)
11-0130 (Dante Series)
11-0128 (Voltaire Series)
FPTB (Arthur Series)
13-0048 (Renoir Series)
FPNZ (Monet Series)
11-0131 (Dali Series)
Assembly
TABLE OF CONTENTS
FMTF (DA VINCI) PULL DOWN FAUCET 19
Parts
Tools
Model:
FMTF (Da Vinci Series)
Assembly
SINGLE HANDLE FAUCET 24
Parts
Tools
Models:
FFCS (Rembrandt Series)
Assembly
DOUBLE HANDLE FAUCET 30
Parts
Tools
Models:
FFCC (Mona Series)
Assembly
TROUBLESHOOTING 36
Safety Instructions
Prior to Installation
Make sure that the cold and hot water lines are turned off.
Wrap all threaded connections with plumber’s tape. Always wrap in a clockwise
direction.
Cover your drain to avoid losing parts.
Do not disassemble the main faucet body, as it has been installed and commissioned
correctly and precisely before delivery to the factory.
To keep the faucet from jamming, flush the water pipe before installation.
Operating conditions: Working pressure at 0.05-1.0 MPa (including cold and hot
water pressure) with applicable water temperature: 39.2°F - 194°F.
Installation Preparation
1. Shut off the water and let the water in the current faucet drain.
2. Assemble needed tools. The tools needed for each installation are included at the
beginning of each section.
3. Loosen the hardware that keeps the current faucet in place. Remove faucet.
Care and Maintenance
To keep the product clean and shining, follow the steps below:
1. Rinse clean with water and dry with a soft cloth.
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners.
3. Do not use cloth with a coarse surface.
4. Unscrew the aerator and clean when necessary.
If soldering the water connections when installing the faucet, remove the O-rings,
cartridges, and washers before applying any heat.
Protect your eyes when cutting or soldering.
Do not over tighten screws/nuts. Finger tighten, then use a wrench/Philips-head
screwdriver to tighten the fixing screw/nut until snug.
1
NOTES
Faucet Model: Purchase Order #: Date:
2
Spring Faucet
3
Spring Faucet
Tools:
Time required:
Wrench
Phillips-head screwdriver +/- 45 minutes
Bucket
Legend:
Hot Water Cold Water Grease
Warning Plumber’s Tape-
Used for a watertight seal on
threaded pipe joints.
4
Spring Faucet
Spring Kitchen Faucet Models
FSNZ (Apollo Series)
FSTB (Sierra Series)
5
Spring Faucets
Spring Kitchen Faucet Models
12-0140 (Van Gogh Series)
6
Spring Faucet
Loosen the fixing nut and screws and Mount faucet to counter top.
put aside.
Plumbers Tape
Secure the hardware into place with Secure the hoses to the hot (red) and
the Base O-ring, nuts, and screws. cold (blue) lines appropriately.
7
Spring Faucet
spray head
spray head
Test the faucet. Make sure that the spray head is
properly secured.
Review the diagram to understand the
hot, cold, and open settings.
8
Pull Down Faucets
9
Pull Down Faucets
Tools:
Time required:
Wrench
Phillips-head screwdriver +/- 45 minutes
Bucket
Legend:
Hot Water Cold Water Grease
Warning Plumber’s Tape-
Used for a watertight seal
on threaded pipe joints.
10
Pull Down Faucets
Pull Down Kitchen Faucet Models
FPBC (Castor Series)
11-0129 (Shakespeare Series)
11
Pull Down Faucets
Pull Down Kitchen Faucet Models
FPBL (Edison Series)
FPTF (Gemini Series)
12
Pull Down Faucets
Pull Down Kitchen Faucet Models
11-0130 (Dante Series)
11-0128 (Voltaire Series)
13
Pull Down Faucets
Pull Down Kitchen Faucet Models
FPTB (Arthur Series)
13-0048 (Renoir Series)
14
Pull Down Faucets
Pull Down Kitchen Faucet Models
FPNZ (Monet Series)
11-0131 (Dali Series)
15
Pull Down Faucets
Loosen the fixing nut and screws and Mount faucet to counter top.
put aside.
Plumbers Tape
Secure the hardware into place with Secure the hoses to the hot and cold
the Base O-ring, nuts, and screws. lines appropriately.
16
Pull Down Faucets
Drain the valve. Secure
Drain
Tighten the
thethehardware
hardware.into place.
valve.
spray head
spray head
Test the faucet. Make sure that the spray head is
properly secured.
17
Pull Down Faucets
Apply the weight to the center of the Review the diagram to understand the
hose for even distribution. hot, cold, and open settings.
18
Pull Down Faucet (FMTF)
1
6
1. Faucet Body
2. Base O-Ring
2 3. Rubber Washer
4. Metal Washer
5. Fixing Nut and Screws
6. Spray Head
3
4
19
Pull Down Faucet (FMTF)
Tools:
Time required:
Wrench
Phillips-head screwdriver +/- 45 minutes
Bucket
Legend:
Hot Water Cold Water Grease
Warning Plumber’s Tape-
Used for a watertight
seal on threaded pipe
joints.
20
Pull Down Faucet (FMTF)
Pull Down Kitchen Faucet Model
FMTF (Da Vinci Series)
21
Pull Down Faucet (FMTF)
Hot
Cold
Turn off the water valves and place a Mount the faucet to the counter top.
bucket beneath, in case of dripping.
Cold
Hot (Blue)
(Red)
9/16-24 UNEF
Hot Cold
Secure the hardware into place with Attach the hot and cold lines to the
the Base O-ring, nuts, and screws. valves appropriately.
22
Pull Down Faucet (FMTF)
spray head
spray head
Test the faucet before installing the Make sure that the spray head is
spray head. properly secured.
Test the faucet. Press the button to switch from stream
to spray.
23
SINGLE HANDLE FAUCETS
24
SINGLE HANDLE FAUCETS
Tools:
Time required:
Wrench
Phillips-head screwdriver +/- 45 minutes
Bucket
Legend:
Hot Water Cold Water Grease
Warning Plumber’s Tape-
Used for a watertight
seal on threaded pipe
joints.
25
SINGLE HANDLE FAUCETS
Kitchen Faucet with Sprayer Models:
FFCS (Rembrandt Series)
26
SINGLE HANDLE FAUCETS
Loosen the fixing nut and screws and Mount faucet to counter top.
put aside.
Plumbers Tape
Secure the hardware into place with Secure the hoses to the hot and cold
the Base O-ring, nuts, and screws. lines appropriately.
27
SINGLE HANDLE FAUCETS
Test the faucet. Loosen the washer on the spray head.
Mount spray head to counter top. Secure the hardware into place with
nuts and screws.
28
SINGLE HANDLE FAUCETS
Tighten the hardware. Review the diagram to understand the
hot, cold, and open settings.
29
DOUBLE HANDLE FAUCETS
30
DOUBLE HANDLE FAUCETS
Tools:
Time required:
Wrench
Phillips-head screwdriver +/- 45 minutes
Bucket
Legend:
Hot Water Cold Water Grease
Warning Plumber’s Tape-
Used for a watertight
seal on threaded pipe
joints.
31
DOUBLE HANDLE FAUCETS
Kitchen Faucet with Sprayer Models:
FFCC (Mona Series)
32
DOUBLE HANDLE FAUCETS
Loosen the fixing nut and washers Mount faucet to counter top.
and put aside.
Secure the hardware into place with Secure the hoses to the hot and cold
the Base O-ring, nuts, and screws. lines appropriately.
33
DOUBLE HANDLE FAUCETS
Loosen the washer on the spray head. Mount spray head to counter top.
Secure the hardware into place with Use the hose to connect the spray
nuts and screws. head and main faucet head.
34
DOUBLE HANDLE FAUCETS
Review the diagram to understand the
hot, cold, and open settings.
35
Troubleshooting
Problem Possible Cause Solution
There is leakage under the The locking nut has Unscrew the lever on the
handle. come loose. handle by hand. Loosen set
screw with a hex wrench.
Remove the handle and
unscrew trim cap by hand.
Tighten locking nut with an
adjustable wrench.
Water will not shut off Cartridge may be Unscrew the level on the
completely. defective. handle by hand. Loosen set
screw with a hex wrench.
Remove the handle and
unscrew trim cap by hand.
Unscrew the locking nut with
an adjustable wrench. Remove
ceramic disc cartridge. Check
for cracks.
There is a leak between the The spray head may be Tighten the spray head by
spray head and the hose. loose or the washer is hand until snug. Make sure the
not seated correctly in washer is seated correctly.
the hose connection.
36
Kitchen and Bath
Three Locations:
350 Parr Circle
Reno, NV 89512
916 Delaware Avenue
Marysville, OH 43040
319 Rowland Mill Road
Bruceton, TN 38317
www.zlinekitchen.com
1-614-777-5004
