Scribd
Upload
124 views3 pages

4Runner Combination Meter Overhaul

The document provides instructions for overhauling a combination meter assembly in a 2005 Toyota 4Runner. It involves removing the instrument cluster finish panel, combination meter assembly, speedometer glass, and combination meter cover No. 1. The inclination sensor assembly must also be removed. When reinstalling the combination meter assembly, the check pins must be pulled to be unseen. A zero degree correction of the inclination sensor must be performed after reinstalling the combination meter assembly.

Uploaded by

Frank Smith
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
124 views3 pages

4Runner Combination Meter Overhaul

The document provides instructions for overhauling a combination meter assembly in a 2005 Toyota 4Runner. It involves removing the instrument cluster finish panel, combination meter assembly, speedometer glass, and combination meter cover No. 1. The inclination sensor assembly must also be removed. When reinstalling the combination meter assembly, the check pins must be pulled to be unseen. A zero degree correction of the inclination sensor must be performed after reinstalling the combination meter assembly.

Uploaded by

Frank Smith
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

71−23

INSTRUMENT PANEL/METER − COMBINATION METER ASSY

COMBINATION METER ASSY


710C7−03

OVERHAUL
HINT:
COMPONENTS: See page 71−10

1. REMOVE INSTRUMENT CLUSTER FINISH PANEL


SUB−ASSY
(a) Disengage the 7 clips.
(b) Disconnect the connectors and remove the instrument
cluster finish panel sub−assy.

7 Clips B62746

2. REMOVE COMBINATION METER ASSY


(a) Remove the 3 screws.
(b) Loosen the 2 bolts and remove the combination meter
assy.

B62747

3. REMOVE SPEEDMETER GLASS


(a) Remove the 2 screws.
(b) Disengage the 6 claws and remove the speedometer
glass.

6 Claws B62754

2005 4RUNNER REPAIR MANUAL (RM1165U)

Author: Date: 4134


71−24
INSTRUMENT PANEL/METER − COMBINATION METER ASSY

4. REMOVE COMBINATION METER COVER NO.1


(a) Remove the 10 screws and combination meter cover
No.1.

B62755

5. REMOVE INCLINATION SENSOR ASSY


(a) Remove the 2 screws and inclination sensor assy.

B62756

6. INSTALL COMBINATION METER ASSY


(a) Pull the positions shown in the illustration in the arrow
mark direction to make the check pins unseen form the
surface.

B64629

(b) Check that the connector on the instrument panel side is


in place.
(c) Install the combination meter assy with the 3 screws.
(d) Tighten the screw shown in the illustration and check that
the check pin protrudes.

B63039

7. INCLINATION SENSOR ZERO DEGREE CORRECTION


NOTICE:
S When replacing or removing/installing the combination meter assy and inclination sensor
assy, be sure to perform zero degree correction of the inclination sensor.
S When performing zero degree correction, install the combination meter assy and perform it in
level surface.
S Also perform zero degree correction when the body level setting is inclined because of vehicle
height adjustment.
(a) Turn the ignition switch off.
(b) While pressing the RESET switch, turn the ignition switch on.
2005 4RUNNER REPAIR MANUAL (RM1165U)

Author: Date: 4135


71−25
INSTRUMENT PANEL/METER − COMBINATION METER ASSY

(c) Within 5 seconds after the ignition switch is turned on, repeat pressing and releasing the RESET switch
3 times and keep holding the last press for more than 5 seconds. (Buzzer sounds for a second)
NOTICE:
If the buzzer does not sound, perform this procedure from the beginning.
(d) Release the RESET switch when buzzer sounds.
(e) Press the RESET switch again and keep pressing for more than 5 seconds. (Buzzer sounds for a se-
cond again)
HINT:
S When the buzzer sounds twice, reset operation is completed.
S The buzzer sound of the first and second time is the same.
NOTICE:
If the buzzer does not sound or keep sounding for more than 1 second, perform the procedure from
the beginning.

E236668E02

2005 4RUNNER REPAIR MANUAL (RM1165U)

Author: Date: 4136

You might also like