Scribd
Upload
85 views3 pages

Double Pivot Hook Hoist Datasheet: MODEL U3-DPHK-160 & U3-DPHK-176

The document provides specifications for two double pivot hook hoist models, the U3-DPHK-160 and U3-DPHK-176. Both models have a maximum hook height of 212 inches above the truck frame when dumping and can lift a rated capacity of 30,000 pounds. The main differences are that the U3-DPHK-160 mounts on a tandem axle truck with an axle spacing of 160 inches, while the U3-DPHK-176 mounts on a single axle truck with an axle spacing of 176 inches. Both hoists are made from high strength steel alloys and have hydraulic cylinders, valves, and pumps to power lifting and dumping functions.

Uploaded by

Enoc Arenas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
85 views3 pages

Double Pivot Hook Hoist Datasheet: MODEL U3-DPHK-160 & U3-DPHK-176

The document provides specifications for two double pivot hook hoist models, the U3-DPHK-160 and U3-DPHK-176. Both models have a maximum hook height of 212 inches above the truck frame when dumping and can lift a rated capacity of 30,000 pounds. The main differences are that the U3-DPHK-160 mounts on a tandem axle truck with an axle spacing of 160 inches, while the U3-DPHK-176 mounts on a single axle truck with an axle spacing of 176 inches. Both hoists are made from high strength steel alloys and have hydraulic cylinders, valves, and pumps to power lifting and dumping functions.

Uploaded by

Enoc Arenas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

DOUBLE PIVOT HOOK HOIST DATASHEET

MODEL U3-DPHK-160 & U3-DPHK-176

HOIST MODELS U3-DPHK-160 (Tandem Axle) U3-DPHK-176 (Single Axle)


* (A) MAXIMUM HOOK HEIGHT
ABOVE TRUCK FRAME LOADING / 120 5/16" 120 5/16
UNLOADING
* (B) MAXIMUM HOOK HEIGHT
212 3/8" 212 3/8"
ABOVE TRUCK FRAME DUMPING

(C) CAB TO HOIST 3" 3"

(D) RAISED ANGLE 56° 56°

(E) CAB TO AXLE 160 5/8" (Center of Tandem Axles) 176" (Center of Single Axle)

(F) AFTER FRAME 31" 42"

(G) HOIST LENGTH 219 1/2" 219 1/2"

RATED CAPACITY 30,000 LBS 30,000 LBS

LIFT CYLINDERS 6" X 3 1/2" X 78" 6" X 3 1/2" X 78"

JIB CYLINDER 4" X 2 1/2" X 48" 4: X 2 1/2" X 48"


RECOMMENDED CONTAINER
14 FT - 18 FT 14 FT - 18 FT
LENGTH
APPROX. WEIGHT 5,630 LBS 5,630 LBS

(1) FACTORY TESTED WITH RECOMMENDED CONTAINER LENGTH AND WATER LEVEL LOAD.
(2) WHEN RECOMMENDING CONTAINER LENGTHS; WEIGHT DISTRIBUTION, DUMP ANGLE, AND OVERHANG ARE FACTORS.
(3) NOTED CONTAINER LENGTHS WILL OVERHANG BETWEEN 24" AND UNDER 48". CONSULT SALES REPRESENTATIVE/ENGINEERING
FOR ADDITIONAL DETAILS ON THIS TYPE OF SETUP

* TOTAL MAXIMUM HEIGHT WILL DEPEND ON CONTAINER. CONSULT ENGINEERING FOR CLEARANCE
MODEL U3-DPHK-160 & U3-DPHK-176

CROSS MEMBERS - STRUCTURAL TUBING 62,000 LBS. MIN TENSILE A500 GRADE C

MAIN FRAME - HSLA A572 65,000 LBS. MIN TENSILE

JIB FRAME - A514 T-1 & STRUCTURAL TUBING A500 GRADE C

PIVOT TUBE - A514 T-1 100,000 PSI MINIMUM YIELD

PICKUP HOOK - A514 T-1 100,000 PSI MINIMUM YIELD

LIFT CYLINDER SHAFTS - 2 3/4" SOLID ( 64,000 LB. TENSILE )

HINGE SHAFT - 2" SOLID ( 64,000 LB. TENSILE )

JIB BEARING - A514 T-1 100,000 PSI MINIMUM YIELD BAR

OUTBOARD SUPPORTED UPPER LIFT SHAFT

MECHANICAL INTERLOCK BETWEEN TAIL AND PIVOT ASSEMBLY

OUTSIDE CONTROLS STANDARD

STEEL FENDERS STANDARD

FULL WIDTH BUMPER WITH RECESSED LED LIGHTS STANDARD

RUBBER MOUNTED SEALED LIGHTS STANDARD

INSIDE AIR OPERATED CONTROLS STANDARD

ALL PIVOT JOINTS HAVE HARDENED STEEL BUSHINGS AND GREASE FITTINGS

PAINTED BLACK

HOIST MODELS U3-DPHK-160 U3-DPHK-176

(H) HOOK HEIGHT 54" 54"


CYCLE TIMES AT APPROXIMATELY 37.5 GPM

EXTENDING DUMP - 31 SECONDS EXTENDING JIB - 5 SECONDS

RETRACTING DUMP - 21 SECONDS RETRACTING JIB - 3 SECONDS

HYDRAULIC SYSTEM

GEAR PUMP 37.5 GPM AT 1500 RPM RATED 4000 PSI DIRECT MOUNT

HYDRAULIC VALVE -OUTSIDE CONTROL LEVERS WITH PROPORTIONAL CONTROLS WITH AIR OPERATED

STEEL RESERVOIR WITH 10 MICRON AIR BREATHER, 3 MICRON IN TANK RETURN FILTER AND FILLER, SIGHT GAUGE WITH TEMPERATURE GAUGE

6" 4,000 PSI LIFTING CYLINDERS WITH BUILT-IN COUNTERBALANCE VALVES

4" 4,000 PSI JIB CYLINDER WITH BUILT-IN COUNTERBALANCE VALVE

OPERATING PRESSURE - 3800 PSI

MINIMUM TRUCK SPECIFICATIONS

FRONT AXLE: 12,000 LBS (WITH POWER STEERING)

REAR AXLE: 26,000 LBS

50,000 PSI CHASSIS TRUCK FRAME OR MORE: MINIMUM SECTIONS MODULUS - 17.5 IN3

You might also like