Sandvik DTH hammers

Product catalogue
Products from Sandvik Mining and Construction Tools
DTH Drilling Products

General Information
Hammer Air Consumption
Air consumption information is generated from laboratory testing in shallow holes and without water injection. A complete list of air
consumption for each hammer can be found in its corresponding operation and maintenance manual.

Hammer Length to Shoulder of Thread

Hammer Length with Bit
Hammer Length with Bit Extended

Conversion Factors

to Convert---------------Multiply By -------------------- to Get

Weight
Pound Mass...................... 0.454 .................................. kg
Length
inches .......................... 25.40 ............................ millimeters
feet ........................... 0.3048 .............................. meters
Penetration Rate
feet/min. ....................... 0.3048 .............................. m/min.
Air Flow
cfm .......................... 0.02832 ............................ m3/min.
cfm ............................ 0.472 ..............................ltrs./sec.
liters/sec.......................... 0.06 ............................... m3/min.
Pressure
psi........................... add 14.7 ...............................PSIG
psi........................... 0.06895 ................................bar
psi............................ 6895.0 ................................. Pa
Temperature
Fahrenheit ...................5/9 (°F–32) ..........................Celcius
Volume
quarts ......................... 0.9463 ................................liters
Blow Energy
Ft. Lbs. ......................... 1.356 ................................joules
Sandvik DTH drilling tools
RH550r hammer 3”
Replacement parts Weight Part No.
Item description
kg lb
1. Top subs
2 3/8” API reg. pin 5 11,0 33-3A001/16A
2. O-ring top sub (3) ID and OD In seal kit
3. Check valve dart with spring 0,3 0,7 25-99006A
1 4. Check valve dart spring 0,02 0,0 22-99071
5. Check valve guide 0,23 0,5 39-3A001
6. Feed tube with retainer pin 0,03 0,1 12-99021
7. Choke Set, Blank 1/8”, 3/16”, & 1/4” 0,1 0,2 29-48017A
8. Feed tube with retainer pin & blank choke 0,45 1,0 37-3A001A
2 9. Piston 3,86 8,5 36-3A081
10. Piston case with retainer ring 10,9 24,0 35-3A006A
11. Piston retainer ring 0,05 0,1 23-99027
3
12. O-rings - guide sleeve, bit retainer (3 req.) In seal kit
13. Guide sleeve with 2 O-rings (#12) 1 2,2 26-3A010A
4
14. Bit retainer ring with O-ring (#12) 0,09 0,2 27-3A006A
5 15. Driver sub (O-ring not req.) 2,18 4,8 34-3A006
10
6

7
Seal Kit
3 piece of #2 & 7 of #12 0,25 0.5 38-3A056

Rebuild Kit
1 piece of #1, 1 of #10, 1 of #15 & Seal kit
11
8 2 3/8” API reg. pin 18,1 40 38-3A001/16
12

13 Complete hammer
2 3/8” API reg. pin top sub 32-5530-RMA/16S

12
14
9

15

Model No Weight Outside diameter Hammer length Hammer length with bit
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

25 55 81,3 3.2 823 32.4 875 34.4 911 35.9

Model No Air consumption, cfm Air consumption, m3/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

172 304 436 4,87 8,61 12,34

Sandvik DTH drilling tools
RH550r hammer 4”
Replacement parts Weight Part No.
Item description
kg lb
1. Top Subs with 3 O-Rings
2 3/8” API Reg. Pin 10 22 33-48001-1/16A
2 7/8” API Reg. Pin 10 22 33-48001-1/11A
2. O-Ring Top Sub OD (1) In seal kit
1
3. O-Ring Top Sub ID (2) In seal kit
4. Check Valve Dart (with spring) 0,3 0,66 25-99001A
5. Check Valve Spring 0,02 0,04 22-99071
6. Check Valve Guide 0,2 0,44 39-48001-1
7. Choke Set, Blank 1/8”, 3/16”, & 1/4” 0,1 0,22 29-48017A
2 8. Feed Tube Retainer Pin 0,03 0,07 12-99014
3 9. Tuning Ring for low volume (optional) 0,23 0,51 56-48552
12
10. Feed Tube With Retainer Pin and Blank Choke 0,7 1,54 37-48001-1A

4 11. Piston 7 15,40 36-48J81

12. Piston Case with Retainer Ring 15 33,00 35-48014A
5
13. Piston Retainer Ring 0,05 0,11 23-99029
14. O-Rings Guide Sleeve & Bit Ret. (3) In seal kit
6
15. Guide Sleeve with 2 O-Rings (Item 14) 1,8 3,96 26-48J10A
16. Bit Retainer Ring w/O-Ring (Item 14) 0,23 0,51 27-48006A

13 17. Driver Sub 3,2 7,04 34-48006

7
14
8
Seal Kit

9 15 1 piece of 2, 2 of 3 & 7 of 14 0,25 0.5 38-48056-1

Rebuild Kit
10 14 1 piece of 1, 1 of 12, 1of 17 & Seal Kit
16 2 3/8” API Reg. Pin 28 62 38-48001/16
2 7/8” API Reg. Pin 28 62 38-48001/11

17

Complete Hammer
2 3/8” API Reg. Pin top sub 32-5540-RMA/16S
11
2 7/8” API Reg. Pin top sub 32-5540-RMA/11S

Model No Weight Outside diameter Hammer length Hammer length with bit
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

38 83 98 3.56 914 36 989 38.9 1029 40.5

Model No Air consumption, cfm Air consumption, m3/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

180 370 560 5,1 10,5 15,9

Low Volume Option 151 315 466 4,3 8,9 13,2
Sandvik DTH drilling tools
RH550 hammer 5”
Replacement parts Weight Part No.
Item description
kg lb
1. Top Subs with 3 O-Rings
3 1/2” API Reg. Pin 10 22,00 33-58D01/04A
2 7/8” API Reg. Pin 10 22,00 33-58D01/11A

1 2. O-Ring Top Sub OD (1) In Seal Kit

3. O-Ring Top Sub ID (2) In Seal Kit
4. Check Valve Dart (with spring) 0,3 0,66 25-99002A
5. Check Valve Spring 0,02 0,04 22-99072
6. Check Valve Guide 0,3 0,66 39-58S01
2
7. O-Ring Feed Tube (1) In Seal Kit
3 8. Choke Set, Blank 1/8”, 3/16”, & 1/4” 0,12 0,26 29-68017A
9. Feed Tube Retainer Pin 0,09 0,20 12-99018
4 10. Feed Tube With Retainer Pin and Blank Choke 0,03 0,07 56-58552
11. Tuning Ring for low volume (optional) 1 2,20 37-58001A
12. Piston 12 26,40 36-58J81
5 13
13. Piston Case with Retainer Ring 27 59,40 35-58D06A
14. Piston Retainer Ring 0,05 0,11 23-99032

6 15. O-Rings Guide Sleeve & Bit Ret. (3) In Seal Kit
16. Guide Sleeve with 2 O-Rings (Item 14) 3 6,60 26-58J10A
17. Bit Retainer Ring w/O-Ring (Item 14) 0,5 1,10 27-58006A
18. Driver Sub 6 13,20 34-58D69
7
8
Seal Kit
9 14
10 1 piece of 2, 2 of 3, 1 of 7 & 7 of 15 0,45 0,99 38-58D56
15

11 Rebuild Kit
1 piece of 1, 1 of 13, 1of 18 & Seal Kit
16
3 1/2” API Reg. Pin 43 94,60 38-58D01/04
2 7/8” API Reg. Pin 43 94,60 38-58D01/11
15

12 17
18 Complete Hammer
3 1/2” API Reg. Pin top sub 32-5550-SMA/04S
2 7/8” API Reg. Pin top sub 32-5550-SMA/11S

Model No Weight Outside diameter Hammer length Hammer length with bit
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

68 145 120 4,72 987 38,86 1082 42.6 1122 44.2

Model No Air consumption, cfm Air consumption, m3/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

305 580 855 8.64 16.42 24.21

Low Volume Option 285 540 790 8.07 15.25 22.37
Sandvik DTH drilling tools
RH550g hammer 5”
Replacement parts Weight Part No.
Item description
kg lb
1. Top Subs with 3 O-Rings
3 1/2” API Reg. Pin 18 39,6 33-58D02/04A
2 7/8” API Reg. Pin 18 39,6 33-58D02/11A

1 2. O-Ring Top Sub OD (1) In Seal Kit

3. O-Ring Top Sub ID (2) In Seal Kit
4. Check Valve Dart (with spring) 0,3 0,66 25-99002A
5. Check Valve Spring 0,02 0,04 22-99072
6. Check Valve Guide 0,3 0,66 39-58S01
2
7. O-Ring Feed Tube (1) In Seal Kit
3 8. Choke Set, Blank 1/8”, 3/16”, & 1/4” 0,12 0,26 29-68017A
9. Feed Tube Retainer Pin 0,09 0,20 12-99018
4 10. Feed Tube With Retainer Pin and Blank Choke 0,03 0,07 56-58552
11. Tuning Ring for low volume (optional) 1 2,20 37-58001A
12. Piston 12 26,40 36-58J81
5 13
13. Piston Case with Retainer Ring 29 63,8 35-58D07A
14. Piston Retainer Ring 0,05 0,11 23-99032

6 15. O-Rings Guide Sleeve & Bit Ret. (3) In Seal Kit
16. Guide Sleeve with 2 O-Rings (Item 14) 3 6,60 26-58J10A
17. Bit Retainer Ring w/O-Ring (Item 14) 0,5 1,10 27-58006A
18. Driver Sub 7 15,4 34-58D70

7
8 Seal Kit
9 14
1 piece of 2, 2 of 3, 1 of 7 & 7 of 15 0,45 0,99 38-58D56
10 15

Rebuild Kit
11
1 piece of 1, 1 of 13, 1of 18 & Seal Kit
16
3 1/2” API Reg. Pin 54 118,8 38-58D02/04
15 2 7/8” API Reg. Pin 54 118,8 38-58D02/11
17
15

12
18 Complete Hammer
3 1/2” API Reg. Pin top sub 32-5555-GMA/04C
2 7/8” API Reg. Pin top sub 32-5555-GMA/11C

Model No Weight Outside diameter Hammer length Hammer length with bit
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

73 160 126 4,96 987 38,86 1082 42.6 1122 44.2

Model No Air consumption, cfm Air consumption, m3/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

305 580 855 8.64 16.42 24.21

Low Volume Option 285 540 790 8.07 15.25 22.37
Sandvik DTH drilling tools
RH550 hammer 6”
Replacement parts Weight Part No.
Item description
kg lb
1. Top sub with 3 O-rings
3 1/2” API reg. pin 20 44 33-68D08/04A
2. O-ring top sub OD (1) In seal kit
1
3. O-ring top sub ID (2) In seal kit
4. Check valve dart with spring 0,3 0.66 25-99002A
5. Check valve dart spring 0,02 0.044 22-99072
6. Check valve guide 0,3 0.66 39-68001

2 7. Choke Set, Blank 1/8”, 3/16”, & 1/4” 0,12 0.264 29-68017A
8. Feed tube retainer pin 0,2 0,44 12-99013
3
9. Feed Tube With Retainer Pin and Blank Choke 1 2.2 37-68601A
10. Piston 18 39.6 36-68J81

4 11. Piston case with retainer ring 33 72.6 35-68D14A

12. Piston retainer ring 0,1 0.22 23-99028
13. O-rings - guide sleeve, bit retainer (3) In seal kit
14. Guide sleeve with 2 O-rings (#13) 4 8.8 26-68J10A
5
15. Bit retainer ring with O-ring (#13) 1 2.2 27-68006A
11
16. Driver sub 6 13.2 34-68D69

Seal Kit
1 piece of #2, 2 of #3 & 7 of #13 0,25 0.55 38-68656
7
12 Rebuild Kit

8 1 piece of #1, 1 of #11, 1 of #16 & Seal kit

13
3 1/2” API reg. pin 20 44 38-68D08/04
9
14

13

15 Complete hammer
13 3 1/2” API reg. pin top sub 32-5560-SMA/04S

10 16

Model No Weight Outside diameter Hammer length Hammer length with bit
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

72 158 142 5.6 922 36.3 1008 39.7 1046 41.2

Model No Air consumption, cfm Air consumption, m3/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

343 659 972 9,8 18,7 27,5

Sandvik DTH drilling tools
RH550g hammer 6”
Replacement parts Weight Part No.
Item description
kg lb
1. Top sub with 3 O-rings
3 1/2” API reg. pin 22 48.40 33-6L009/04CA
2. O-ring top sub OD (1) In seal kit
1
3. O-ring top sub ID (2) In seal kit
4. Check valve dart with spring 0,3 0.66 25-99002A
5. Check valve dart spring 0,02 0.044 22-99072
6. Check valve guide 0,3 0.66 39-68001

2 7. Choke Set, Blank 1/8”, 3/16”, & 1/4” 0,12 0.264 29-68017A
8. Feed tube retainer pin 0,2 0,44 12-99013
3
9. Feed Tube With Retainer Pin and Blank Choke 1 2.2 37-68601A
10. Piston 18 39.6 36-68J81

4 11. Piston case with retainer ring 33 72.6 35-6LD68A

12. Piston retainer ring 0,1 0.22 23-99028
13. O-rings - guide sleeve, bit retainer (3) In seal kit
14. Guide sleeve with 2 O-rings (#13) 4 8.8 26-68J10A
5
15. Bit retainer ring with O-ring (#13) 1 2.2 27-68006A
11
16. Driver sub 6 13.2 34-6LD70

Seal Kit
1 pieces of #2, 2 of #3 & 7 of #13 0,25 0.5 38-68656
7
12 Rebuild Kit

8 1 piece of #1, 1 of #11, 1 of #16 & Seal kit

13
3 1/2” API reg. pin 62 136.40 38-6LD09/04C
9
14

13

15 Complete hammer
13 3 1/2” API reg. pin 32-5565-GMA/04C

10 16

Model No Weight Outside diameter Hammer length Hammer length with bit
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

82 180 150 5.9 922 36.3 1008 39.7 1046 41.2

Model No Air consumption, cfm Air consumption, m3/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

343 659 972 9,8 18,7 27,5

Sandvik DTH drilling tools
RH550r hammer 6”
Replacement parts Weight Part No.
Item description
kg lb
1. Top sub with 3 O-rings
3 1/2” API reg. pin 22 48.40 33-68602/04CA
2. O-ring top sub OD (1) In seal kit
1
3. O-ring top sub ID (2) In seal kit
4. Check valve dart with spring 0,3 0.66 25-99002A
5. Check valve dart spring 0,02 0.044 22-99072
6. Check valve guide 0,3 0.66 39-68001

2 7. Choke Set, Blank 1/8”, 3/16”, & 1/4” 0,12 0.264 29-68017A
8. Feed tube retainer pin 0,2 0,44 12-99013
3
9. Feed Tube With Retainer Pin and Blank Choke 1 2.2 37-68601A
10. Piston 18 39.6 36-68J81

4 11. Piston case with retainer ring 33 72.6 35-68668A

12. Piston retainer ring 0,1 0.22 23-99028
13. O-rings - guide sleeve, bit retainer (3) In seal kit
14. Guide sleeve with 2 O-rings (#13) 4 8.8 26-68J10A
5
15. Bit retainer ring with O-ring (#13) 1 2.2 27-68006A
11
16. Driver sub 6 13.2 34-68670

Seal Kit
1 pieces of #2, 2 of #3 & 7 of #13 0,25 0.5 38-68656
7
12 Rebuild Kit

8 1 piece of #1, 1 of #11, 1 of #16 & Seal kit

13
3 1/2” API reg. pin 62 136.40 38-68602/04C
9
14

13

15 Complete hammer
13 3 1/2” API reg. pin 32-5565-RMA/04C

10 16

Model No Weight Outside diameter Hammer length Hammer length with bit
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

82 180 150 5,9 922 36.3 1008 39.7 1046 41.2

Model No Air consumption, cfm Air consumption, m3/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

343 659 972 9,8 18,7 27,5

Sandvik DTH drilling tools
RH550w hammer 6”
Replacement parts Weight Part No.
Item description
kg lb
1. Top sub with 3 O-rings
3 1/2” API reg. pin 20 44 33-68N08/04A
2. O-ring top sub OD (1) In seal kit
1
3. O-ring top sub ID (2) In seal kit
4. Check valve dart with spring 0,3 0.66 25-99002A
5. Check valve dart spring 0,02 0.044 22-99072
6. Check valve guide 0,3 0.66 39-68001

2 7. Choke Set, Blank 1/8”, 3/16”, & 1/4” 0,12 0.264 29-68017A
8. Feed Tube Retainer pin 0,2 0,44 12-99013
3
9. Tuning Ring 0,4 0,9 56-68552
10. Feed Tube With Retainer Pin and Blank Choke 1 2.2 37-68301A

4 11. Piston 18 39.6 36-68J81

12. Piston case with retainer ring 33 72.6 35-68D14A
13. Piston retainer ring 0,1 0.22 23-99028
14. O-rings - guide sleeve, bit retainer (3 req.) In seal kit
5
15. Guide sleeve with 2 O-rings (#13) 4 8.8 26-68J10A
12
16. Bit retainer ring with O-ring (#13) 1 2.2 27-68006A

6 17. Driver sub 6 13.2 34-68D69

Seal Kit
7 1 pieces of #2, 2 of #3 & 7 of #14 0,25 0.5 38-68656

Rebuild Kit

8 13 1 piece of #1, 1 of #12, 1 of #17 & Seal kit

9 14 3 1/2” API reg. pin 20 44 38-68N08/04

15
10

14
16 Complete hammer
14 3 1/2” API reg. pin 32-5560-WMA/04S

17
11

Model No Weight Outside diameter Hammer length Hammer length with bit
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

72 158 142 5.6 922 36.3 1008 39.7 1046 41.2

Model No Air consumption, cfm Air consumption, m3/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

395 759 1120 11,2 21,5 31,7

Low volume option 345 680 1000 9,8 19,3 28,3
Sandvik DTH drilling tools
RH550r hammer 8”
Replacement parts Weight Part No.
Item description
kg lb
1. Top Subs with 3 O-Rings
4 1/2” API Reg. Pin 42 92,4 33-88002/19CA
2. O-Ring Top Sub OD (1) In Seal Kit
3. O-Ring Top Sub ID (2) In Seal Kit
1 4. Check Valve Dart (with spring) 0,5 1,1 38-11663A
5. Check Valve Spring 0,1 0,22 38-1/1235-073
6. Check Valve Guide 0,7 1,54 39-88001
2 7. Choke Set, Blank 1/8”, 3/16”, & 1/4” 0,12 0,264 29-68017A
8. Feed Tube Retainer Pin 0,2 0,44 12-99016
3
9. Tuning Ring for low volume (optinal) 0,8 1,76 56-88552
10. Feed Tube With Retainer Pin and Blank Choke 2,2 4,84 37-88001A

4 11. Piston 42 92,4 36-88J81

12. Piston Case with Retainer Ring 56 123,2 35-88002A
13. Piston Retainer Ring 0,2 0,44 23-99030

5 14. O-Rings Guide Sleeve & Bit Ret. (3) In Seal Kit
12
15. Guide Sleeve with 2 O-Rings (#14) 11 24,2 26-88J10A
16. Bit Retainer Ring w/O-Ring (#14) 1,9 4,18 27-88006A

6 17. Driver Sub 17 37,4 34-88007

7
13 Seal Kit
1 piece of 2, 2 of 3 & 7 of 14 0,25 0,55 38-88056
8 14

9 Rebuild Kit

10 1 piece of 1, 1 of 12, 1of 17 & Seal Kit

15
4 1/2” API Reg. Pin 115 253 38-88002/19C

14
16
14
Complete Hammer
11 17 4 1/2” API Reg. Pin top sub 32-5585-RMA/19C

Model No Weight Outside diameter Hammer length Hammer length with bit
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

173 380 181 7,12 1219 48 1310 51,6 1354 53,3

Model No Air consumption, cfm Air consumption, m3/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

460 850 1240 13 23.8 35.1

Low Volume Option 300 560 830 8.5 15.9 23.5
Sandvik DTH drilling tools
RH550w hammer 8”
Replacement parts Weight Part No.
Item description
kg lb
1. Top Subs with 3 O-Rings
4 1/2” API Reg. Pin 42 92,40 33-88302/19A
2. O-Ring Top Sub OD (1) In Seal Kit
1 3. O-Ring Top Sub ID (2) In Seal Kit
4. Check Valve Dart (with spring) 0,5 1,10 38-11663A
5. Check Valve Spring 0,1 0,22 38-1/1235-073
6. Check Valve Guide 0,7 1,54 39-88001
2
7. Choke Set, Blank 1/8”, 3/16”, & 1/4” 0,12 0,26 29-68017A
3 8. Feed Tube Retainer Pin 0,2 0,44 12-99016
9. Feed Tube With Retainer Pin and Blank Choke 2,2 4,84 37-88301A
10. Piston 42 92,40 36-88J81
4 11. Piston Case with Retainer Ring 56 123,20 35-88302A
12. Piston Retainer Ring 0,2 0,44 23-99030
13. O-Rings Guide Sleeve & Bit Ret. (3) In Seal Kit
5 14. Guide Sleeve with 2 O-Rings (#14) 11 24,20 26-88J10A
15. Bit Retainer Ring w/O-Ring (#14) 1,9 4,18 27-88006A
11
16. Driver Sub 17 37,40 34-88007
6

7
Seal Kit
12
8 1 piece of 2, 2 of 3 & 7 of 13 0,25 0,55 38-88056
13

14 Rebuild Kit
9
1 piece of 1, 1 of 11, 1of 16 & Seal Kit
4 1/2” API Reg. Pin 115 253,00 38-88302/19

13
15

Complete Hammer
10 16
4 1/2” API Reg. Pin top sub 32-5585-WMA/19S

Model No Weight Outside diameter Hammer length Hammer length with bit
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

173 380 181 7.12 1270 50 1361 53,6 1405 55,3

Model No Air consumption, cfm Air consumption, m3/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

525 975 1540 14.9 27.6 43.6

DTH Hammers

Complete Hammer
SD 5 Model No. 32-SD5B/4
32-SD5B/11
32-SD5B/25

Replacement Parts Weight

Item Description kg lb Part No.
1 Top Subs 31/2" API Reg Pin Up /04 13 28 33-23048A
2 7/8" API Reg Pin Up /11 13 28 33-23049A
13
1
3 /2" API Reg Box Up /25 14 32 33-23047A
1 14
2 O-Ring (2 req.) – Top & Driver Sub
2
3 Check Valve Dart with Spring 0,7 1.5 25-99001A
10
15 4 Check Valve Dart Spring 0,1 0.3 22-99071
2
5 Check Valve Guide 2 4 39-23036
3 6 Make-Up Ring 0,2 0.5 38-17258
4 7 Choke Set 0,5 1.2 38-11624A

5 16 8 Rigid Valve with O-Ring 4 8 37-25040A

9 O-Ring – Rigid Valve
6 10 Piston 10 23 36-23044

7
11 Piston Case with Retainer Ring 22 48 35-25037A
12 Piston Retainer Ring 0,09 0.2 23-99015
13 O-Ring – Bit Retainer Ring
8
14 Bit Retainer Ring with O-Ring 0,5 1.2 38-23043A
9 15 Driver Sub 6 14 34-24125A
16 Foot Valve 0,05 0.1 47-51017
11
4-1/388

12 Seal Kit
6 pieces of #2, 1 of #9, & 5 of #13 0,25 0.5 38-51056

Repair Kit
2 pieces of #2, 1 of #3, 1 of #6 + 3 makeup shims, 2 4 38-24590
1 of #7, 1 of #9, 1 of #13, 1 of #14 and 1 of #16

Outside Hammer Hammer Length with Bit

Model Number Weight Diameter Length Bit Closed Bit Extended
kg lb mm inch mm inch mm inch mm inch
32-SD5B 61 134 116 4.56 975 38.4 1067 42.0 1105 43.5
Air Consumption, cfm Air Consumption, m3/min.
Model Number 150 psi 250 psi 350 psi 10 bar 18 bar 24 bar
min. max. min. max. min. max. min. max. min. max. min. max.
32-SD5B 260 410 475 710 700 1020 7,4 11,6 13,5 20,1 19,8 28,9
DTH Hammers

Complete Hammer
SD 6 Model No. 32-SD6/4
32-SD6/25

Replacement Parts Weight

Item Description kg lb Part No.
1 Top Subs
31/2" API Reg Pin Up /4 24 52 33-16610A
13
1 31/2" API Reg Box Up /25 26 57 33-16612A
14

2
2 O-Ring (2 req.) – Top & Driver Sub

10 3 Check Valve Dart with Spring 0,3 0.6 25-99002A

15
2 4 Check Valve Dart Spring 0,1 0.3 22-99072

3
5 Check Valve Guide 2,3 5 39-16602
6 Make-Up Ring 0,2 0.5 38-16603
4
7 Choke Set 0,7 1.5 38-16607A
5 16
8 Rigid Valve with O-Ring 6 13 37-23042A
6 9 O-Ring – Rigid Valve

7
10 Piston 24 52 36-23041
11 Piston Case with Retainer Ring 32 70 35-23040A

8
12 Piston Retainer Ring 0,09 0.2 38-12040-09
13 O-Ring – Bit Retainer Ring
9
14 Bit Retainer Ring with O-Ring 0,7 1.6 38-16606A

11
15 Driver Sub with O-Ring 7 16 34-24137A
16 Foot Valve 0,4 0.8 47-61017
4-1/388

12

Seal Kit
6 pieces of #2, 1 of #9, and 5 of #13 0,25 0.5 38-61056

Repair Kit
2 pieces of #2, 1 of #3, 1 of #6 + 3 makeup shims, 3 6 38-24592
1 of #7, 1 of #9, 1 of #13, 1 of #14, and 5 of #16

Outside Hammer Hammer Length with Bit

Model Number Weight Diameter Length Bit Closed Bit Extended
kg lb mm inch mm inch mm inch mm inch
32-SD6 101 223 138 5.45 1257 49.5 1370 53.5 1408 55.5
3
Air Consumption, cfm Air Consumption, m /min.
Model Number 150 psi 250 psi 350 psi 10 bar 18 bar 24 bar
min. max. min. max. min. max. min. max. min. max. min. max.
32-SD6 410 610 725 1050 1050 1480 11,6 17,3 20,5 29,7 29,7 41,9
DTH Hammers

Complete Hammer
SD 8 Model No. 32-SD8/19
32-SD8/4

Replacement Parts Weight

Item Description kg lb Part No.
1 Top Subs
31/2" API Reg Pin Up /4 34 75 33-23407A

13 41/2" API Reg Pin Up /19 34 75 33-23412A

1 14 2 O-Ring (2 req.) – Top & Driver Sub
2 3 Check Valve Dart with Spring 0,3 0.6 38-11663A
10 4 Check Valve Dart Spring 0,1 0.3 38-1/1235-073
15
2
5 Check Valve Guide 4,5 10 39-23397
3 6 Make-Up Ring 0,2 0.5 38-17450

4
7 Choke Set 0,7 1.5 38-11890A

16
8 Rigid Valve with O-Ring 6 13 37-23405A
5
9 O-Ring – Rigid Valve
6 10 Piston 31 68 36-25630
7 11 Piston Case with Retainer Ring 60 130 35-23402A
12 Piston Retainer Ring 0,1 0.3 38-23400

8 13 O-Ring – Bit Retainer Ring

14 Bit Retainer Ring with O-Ring 0,7 1.6 38-23398A
9
15 Driver Sub 14 30 34-82006A

11
16 Foot Valve 0,4 0.9 47-81017
4-1/388

12
Seal Kit
6 pieces of #2, 1 of #9, and 5 of #13 4 8 38-81056

Repair Kit
2 pieces of #2, 1 of #3, 1 of #6 +3 Make-up Shims, 4 8 38-24595
1 of #7, 1 of #9, 1 of #13, 1 of #14, and 3 of #16.

Outside Hammer Hammer Length with Bit

Model Number Weight Diameter Length Bit Closed Bit Extended
kg lb mm inch mm inch mm inch mm inch
32-SD8 156 345 171 6.75 1194 47 1410 55.5 1451 57.1
3
Air Consumption, cfm Air Consumption, m /min.
Model Number 150 psi 250 psi 350 psi 10 bar 18 bar 24 bar
min. max. min. max. min. max. min. max. min. max. min. max.
32-SD8 440 830 810 1380 1160 1940 12,5 23,5 22,9 39,1 32,9 54,9
DTH Hammers

Complete Hammer
SD 10 Model No. 32-SD10/39

Replacement Parts Weight

Item Description kg lb Part No.
Lifting Bale/Thread Protector 38-17438-4
15 1 Top Sub with O-Ring – 65/8" API Reg Pin Up /39 72 158 33-23888A
1
16 2 O-Ring, (2 Req) Top & Driver Sub

2
3 Check Valve Dart with Spring 0,7 1.5 38-11663A
12
2 4 Check Valve Dart Spring 0,1 0.3 38-1/1235-073
5 Check Valve Guide 10 21 39-23859
3

4
6 Make-Up Ring 0,2 0.5 38-23855
17 7 Rigid Valve Finger Retainer 0,14 0.3 38-24083-2
5

18 8 Choke Set 0,7 1.5 38-24093A

6 9 Rigid Valve Finger 0,3 0.7 38-23881

7
10 Rigid Valve with O-Ring & R.V. Finger 13 29 37-23858A
8 11 O-Ring - Rigid Valve
9 12 Piston 64 141 36-23886

10 13 Piston Case with Retainer Ring 109 240 35-23885A

13
14 Piston Retainer Ring 0,3 0.7 38-23883
11
15 O-Ring - Bit Retainer Ring
4-1/432

14 16 Bit Retainer Ring with O-Ring 1,5 3.2 38-23856A

17 Driver Sub with O-Ring 42 93 34-23887A
18 Foot Valve 0,5 1.2 47-10017

Seal Kit

5 of #2, 1 of #11 and 4 of #15 5 11 38-10056

Repair Kit

1 piece of #3, 1 of #6 +3 Make-up 5 11 38-24596

Shims, 1 of #7, 1 of #8, 1 of #11, 1 of #14,
1 of #15, 1 of #16 & 3 of #18.

Outside Hammer Hammer Length with Bit

Model Number Weight Diameter Length Bit Closed Bit Extended
kg lb mm inch mm inch mm inch mm inch
32-SD10 311 685 225 8.88 1387 54.6 1556 61.3 1597 62.9
3
Air Consumption, cfm Air Consumption, m /min.
Model Number 150 psi 250 psi 350 psi 10 bar 18 bar 24 bar
min. max. min. max. min. max. min. max. min. max. min. max.
32-SD10 660 1080 1235 1690 – – 18,7 30,6 35,0 47,9 – –
Not recommended for higher pressure than 250 PSI or 18 Bars.
DTH Hammers

Complete Hammer
X2S Model No. 32-X2S/39

Replacement Parts Weight

Item Description kg lb Part No.
1. Top Sub with 3 O-Rings (2a&b), 118 260 33-1B001/39A
6 5/8" API Reg. Pin
10 2a. O-Ring Top Sub (Spares in Seal Kit)

7
2b. O-Rings Feed Tube (2) (Spares in Seal Kit)
1
3. Check Valve Dart 3,5 7.8 38-11517A
4. Check Valve Spring 0,1 0.3 38-1/1235-074
14a 5. Check Valve Guide 3,1 6.8 39-1B001
2a
2b 6. Choke Set, Blank 1/4", 3/8", & 1/2" 0,2 0.5 29-1B017A
3 7. Feed Tube Retainer Pin (2) 0,9 1.9 12-99019
4 11
12 8. Feed Tube with Retainer Pins, Blank 7,7 17.0 37-1B001A
5 13
14b Choke, & 2 O-Rings (#2b)
6 12
9. Piston 90,3 199 36-1B057
15
10. Piston Case with Retainer Ring 200,5 442 35-1B001A
8
11. Piston Retainer Ring 0,4 0.8 23-99025
12. O-Rings to Driver Sub & Bit Ret. (2) (Spares in Seal Kit)
9
13. Bit Retainer Ring with O-ring 5,3 11.8 27-13001A
14a. Break out Ring, upper 2,7 6.0 15-1B001-01
14b. Break Out Ring, lower 1,8 4.0 15-13001-02
15. Driver Sub 63,1 117 34-14008A
Foot Valve 0,25 0.5 47-12017

Seal Kit
1piece of 2a, 2 pieces of 2b, & 0,5 1 38-1BS56
4 pieces of 12

Outside Hammer Hammer Length with Bit

Model Number Weight Diameter Length Bit Closed Bit Extended
kg lb mm inch mm inch mm inch mm inch
32-X2S 504 1,111 279 11.0 1466 57.71 1596 62.82 1704 67.07
3
Air Consumption, cfm Air Consumption, m /min.
Model Number 150 psi 250 psi 350 psi 10 bar 18 bar 24 bar
min. max. min. max. min. max. min. max. min. max. min. max.
32-X2S 780 1200 1650 2050 22.09 33.98 46.72 58.05
DTH Hammers

Complete Hammer
SD 12 Model No. 32-SD12/39

Replacement Parts Weight

Item Description kg lb Part No.
Lifting Bale/Thread Protector 9 20 38-17438-4
1 Top Sub (with O-Ring) 65/8" API Reg Pin Up /39 127 280 33-23334A
15

16
2 Breakout Ring (2), Top & Driver Sub 0,45 1 38-23343
12
1
3 O-Ring (2), Top & Driver Sub
2
4 Check Valve Dart with Spring 1,4 3 38-11517A
3
5 Check Valve Dart Spring 0,14 0.3 38-1/1235-074
2
3 6 Check Valve Guide 13,6 30 39-19245
4 7 Make-Up Ring 0,36 0.8 38-19246

5 17 8 Choke Set 0,73 1.6 38-18769A

18
9 Rigid Valve Finger 0,36 0.8 38-23341

6
10 Rigid Valve with O-ring & R.V. Finger 16 35 37-23340A
11 O-Ring - Rigid Valve
7
8 12 Piston 75 165 36-23342
13 Piston Case with Retainer Ring 200 441 35-23335A
9
14 Piston Retainer Ring 0,18 0.4 38-12040-07
10 15 O-Ring - Bit Retainer Ring
16 Bit Retainer Ring with O-ring 3,2 7 38-18774A
11 13
4-1/390

17 Driver Sub with O-ring 54 119 34-23337A

14
18 Foot Valve 0,55 1.2 47-12017

Seal Kit
4 of #3, 1 of #11 and 3 of #15 5 11 38-12056

Repair Kit
2 of #2, 2 of #3, 1 of #4,1 of #7 +3 Make-up 5 11 38-24598
Shims, 1 of #8,1 of #11, 1 of #16 and 3 of #18

Outside Hammer Hammer Length with Bit

Model Number Weight Diameter Length Bit Closed Bit Extended
kg lb mm inch mm inch mm inch mm inch
32-SD12 492 1085 273 10.75 1505 59.30 1708 67.20 1759 69.30
Air Consumption, cfm Air Consumption, m3/min.
Model Number 150 psi 250 psi 350 psi 10 bar 18 bar 24 bar
min. max. min. max. min. max. min. max. min. max. min. max.
32-SD12 1100 1490 1550 2030 1900 2380 31,1 42,2 43,9 57,5 53,8 67,4
Sandvik DTH Drill bits
Product catalogue
Products from Sandvik Mining and Construction Tools
Sandvik DTH drilling tools
Bit face designs
Face specifications
Face Button Applications
Concave face Sandvik XT48 Ballistic U Soft to medium rock
U Non Abrasive

Sandvik XT48 Spherical U Soft to medium rock

U Abrasive

Convex face Sandvik XT48 Ballistic U Soft rock

U Non Abrasive

Flat face Sandvik XT48 Spherical U Hard rock

U Abrasive

4• SANDVIK DTH TOOLS

Sandvik DTH drilling tools
Bit shank identification chart
M 30 • 3” L = 224 mm DHD 112 • 12” L = 491 mm
8 Splines 12 Splines

L
L

M 40 • 4” L = 228 mm QL 40 • 4” L = 279,4 mm
12 Splines 10 Splines

L L

M 50 • 5” L = 287 mm QL 50 • 5” L = 240 mm
12 Splines 12 Splines

L L

M 60 • 6” L = 230 mm QL 60 • 6” L = 253,3 mm
12 Splines 12 Splines

L L

M 80 • 8” L = 329 mm QL 80 • 8” L = 331,7 mm
12 Splines 16 Splines

L L

DHD 3.5 • 3” L = 181 mm SD 10 • 10” L = 356 mm

8 Splines 8 Splines

L L

DHD 340 • 4” L = 209 mm SD 12 • 12” L = 468 mm

8 Splines 8 Splines

L L

DHD 350 • 5” L = 261 mm

8 Splines

DHD 360 • 6” L = 308 mm

8 Splines

DHD 380 • 8” L = 350 mm

10 Splines

SANDVIK DTH TOOLS •5

Sandvik DTH drilling tools
Drill bits for RH550 hammers
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
Sandvik RH550 mm inch gauge front Kg lb
M30
Convex face / Ballistic button M30
90 3 1/2 2 8 12 12 4,7 10 42-3A51090-R48
95 3 3/4 2 8 12 12 4,7 10 42-3A510 95-R48
100 3 7/8 2 8 13 13 5,3 12 42-3A54100-R48
105 4 1/8 2 8 14 14 5,3 12 42-3A5B105-R48
Flat face / Spherical button
90 3 1/2 2 8 11 11 4,7 10 42-3AF0090-S48
95 3 3/4 2 8 12 12 4,7 10 42-3AF1095-S48
100 3 7/8 2 8 13 13 5,3 12 42-3AF4100-S48
105 4 1/8 2 8 14 14 5,3 12 42-3AFB105-S48

M40
Concave face / Ballistic button M40
115 4 1/2 2 8 14 14 8,3 18 42-481B115-R48
121 4 3/4 2 8 14 14 8,3 18 42-481B121-R48
127 5 2 8 14 14 8,3 18 42-481B127-R48
130 5 1/8 2 8 16 13 8,3 18 42-4818130-R48
133 5 1/4 2 8 16 13 8,3 18 42-4818133-R48
Concave face / Spherical button
115 4 1/2 2 8 14 14 8,3 18 42-481B115-S48
121 4 3/4 2 8 14 14 8,3 18 42-481B121-S48
127 5 2 8 14 14 8,3 18 42-481B127-S48
130 5 1/8 2 8 16 13 8,3 18 42-4818130-S48
133 5 1/4 2 8 16 13 8,3 18 42-4818133-S48
Convex face / Ballistic button
110 4 3/8 2 8 14 14 8,3 18 42-485B110-R48
115 4 1/2 2 8 14 14 8,3 18 42-485B115-R48
121 4 3/4 2 8 14 14 8,3 18 42-485B121-R48
127 5 2 8 14 14 8,3 18 42-485B127-R48
130 5 1/8 3 9 16 14 8,3 18 42-48L9130-R48
133 5 1/4 3 9 16 14 8,3 18 42-48L9133-R48
Flat face / Spherical button
110 4 3/8 2 8 14 14 8,3 18 42-48FB110-S48
115 4 1/2 2 8 14 14 8,3 18 42-48FB115-S48
121 4 3/4 2 8 14 14 8,3 18 42-48FB121-S48
127 5 2 8 14 14 8,3 18 42-48FB127-S48
130 5 1/8 2 8 16 14 8,3 18 42-48F9130-S48
133 5 1/4 2 8 16 14 8,3 18 42-48F9133-S48

6• SANDVIK DTH TOOLS

Sandvik DTH drilling tools
Drill bits for RH550 hammers
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
Sandvik RH550 mm inch gauge front Kg lb
M50
Concave face / Ballistic button M50
130 5 1/8 2 8 16 13 13,9 31 42-5818130-R48
133 5 1/4 2 8 16 13 14,3 31 42-5818133-R48
140 5 1/2 2 8 16 14 15,0 33 42-5819140-R48
140 5 1/2 3 9 16 14 15,0 33 42-58D9140-R48
146 5 3/4 2 8 16 14 16,0 35 42-5819146-R48
152 6 2 8 16 16 17,1 38 42-581C152-R48
Concave face / Spherical button
130 5 1/8 2 8 16 13 13,9 31 42-5818130-S48
133 5 1/4 2 8 16 13 14,3 31 42-5818133-S48
140 5 1/2 2 8 16 14 15,0 33 42-5819140-S48
140 5 1/2 3 9 16 14 15,0 33 42-58D9140-S48
146 5 3/4 2 8 16 14 16,0 35 42-5819146-S48
152 6 2 8 18 16 17,1 38 42-581D152-S48
Convex face / Ballistic button
130 5 1/8 3 9 16 14 13,9 31 42-58L9130-R48
133 5 1/4 3 9 16 14 14,3 31 42-58L9133-R48
140 5 1/2 3 9 16 16 15,0 33 42-58LC140-R48
146 5 3/4 3 9 16 16 16,0 35 42-58LC146-R48
152 6 3 9 18 16 17,1 38 42-58LD152-R48
Flat face / Spherical button
130 5 1/8 2 8 16 14 13,9 31 42-58F9130-S48
133 5 1/4 2 8 16 14 14,3 31 42-58F9133-S48
140 5 1/2 3 9 16 14 15,0 33 42-5829140-S48
146 5 3/4 3 9 16 14 16,0 35 42-5829146-S48
152 6 3 9 18 16 17,1 38 42-582D152-S48

SANDVIK DTH TOOLS •7

Sandvik DTH drilling tools
Drill bits for RH550 hammers
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
Sandvik RH550 mm inch gauge front Kg lb
M60
Concave face / Ballistic button M60
152 6 2 8 16 16 21,8 48 42-681C152-R48
155 6 1/8 2 8 16 16 21,8 48 42-681C155-R48
159 6 1/4 2 8 16 16 22,9 50 42-681C159-R48
165 6 1/2 3 9 18 18 22,9 50 42-68DE165-R48
172 6 3/4 3 9 18 18 25,0 55 42-68DE172-R48
178 7 3 9 18 18 25,0 55 42-68DE178-R48
190 7 1/2 3 9 18 18 27,0 60 42-68DE190-R48
203 8 3 9 18 18 29,1 64 42-68DE203-R48
Concave face / Spherical button
152 6 2 8 18 16 21,8 48 42-681D152-S48
155 6 1/8 2 8 18 16 21,8 48 42-681D155-S48
159 6 1/4 2 8 18 16 22,9 50 42-681D159-S48
165 6 1/2 3 9 18 16 22,9 50 42-68DD165-S48
165 6 1/2 3 9 18 18 22,9 50 42-68DE165-S48
172 6 3/4 3 9 18 18 25,0 55 42-68DE172-S48
178 7 3 9 18 18 25,0 55 42-68DE178-S48
190 7 1/2 3 9 18 18 27,0 60 42-68DE190-S48
203 8 3 9 18 18 29,1 64 42-68DE203-S48
Convex face / Ballistic button
152 6 3 9 18 16 22,9 50 42-68LD152-R48
155 6 1/8 3 9 18 16 22,9 50 42-68LD155-R48
159 6 1/4 3 9 18 16 22,9 50 42-68LD159-R48
165 6 1/2 3 9 18 18 23,9 53 42-68GE165-R48
172 6 3/4 3 9 18 18 25,0 55 42-68GE172-R48
178 7 3 9 18 18 25,0 55 42-68GE178-R48
203 8 3 9 18 18 29,1 64 42-68GE203-R48
Flat face / Spherical button
152 6 3 9 18 16 22,9 50 42-682D152-S48
155 6 1/8 3 9 18 16 22,9 50 42-682D155-S48
159 6 1/4 3 9 18 16 22,9 50 42-682D159-S48
165 6 1/2 3 9 18 18 23,9 53 42-682E165-S48
172 6 3/4 3 9 18 18 25,0 55 42-682E172-S48
178 7 3 9 18 18 25,0 55 42-682E178-S48
190 7 1/2 3 9 18 18 27,0 60 42-682E190-S48
203 8 3 9 18 18 29,1 64 42-682E203-S48

8• SANDVIK DTH TOOLS

Sandvik DTH drilling tools
Drill bits for RH550 hammers
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
Sandvik RH550 mm inch gauge front Kg lb
M80
Concave face / Spherical button M80
200 7 7/8 3 9 18 18 41,0 90 42-88PE200-S48
203 8 3 9 18 18 41,0 90 42-88PE203-S48
216 8 1/2 3 9 18 18 42,0 93 42-88PE216-S48
219 8 5/8 3 9 18 18 42,0 93 42-88PE219-S48
222 8 3/4 3 12 18 18 49,0 108 42-888E222-S48
226 8 7/8 3 12 18 18 51,0 112 42-888E226-S48
229 9 3 12 18 18 53,0 117 42-888E229-S48
241 9 1/2 3 12 18 18 57,0 126 42-888E241-S48
251 9 7/8 3 12 18 18 57,0 126 42-888E251-S48
254 10 3 12 18 18 57,0 126 42-888E254-S48
270 10 5/8 3 12 18 18 61,0 134 42-888E270-S48
305 12 3 12 18 18 77,0 170 42-888E305-S48
Convex face / Ballistic button
203 8 3 9 18 18 41,0 90 42-88GE203-R48
216 8 1/2 3 9 18 18 42,0 93 42-88GE216-R48
222 8 3/4 3 12 18 18 49,0 108 42-88CE222-R48

Flat face / Spherical button

203 8 3 9 18 18 41,0 90 42-882E203-S48
216 8 1/2 3 9 18 18 42,0 93 42-882E216-S48
222 8 3/4 3 12 18 18 49,0 108 42-88KE222-S48
229 9 3 12 18 18 53,0 117 42-88KE229-S48

SANDVIK DTH TOOLS •9

Sandvik DTH drilling tools
Drill bits with DHD 3.5 & DHD 340 shanks
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
Sandvik RH450 / RH350 mm inch gauge front Kg lb
DHD 3.5
Convex face / Ballistic button DHD 3.5
90 3 1/2 2 8 12 12 4,5 10 42-2451090-R48
95 3 3/4 2 8 12 12 4,5 10 42-2451095-R48
100 3 7/8 2 8 13 13 5,0 11 42-2454100-R48
105 4 1/8 2 8 14 14 5,5 12 42-245B105-R48
Flat face / Spherical button
90 3 1/2 2 8 11 11 4,5 10 42-24F0090-S48
95 3 3/4 2 8 12 12 4,5 10 42-24F1095-S48
100 3 7/8 2 8 13 13 5,0 11 42-24F4100-S48
105 4 1/8 2 8 14 14 5,5 12 42-24FB105-S48

DHD 340
Concave face / Ballistic button DHD 340
115 4 1/2 2 8 14 14 9,0 20 42-361B115-R48
121 4 3/4 2 8 14 14 11,0 24 42-361B121-R48
127 5 2 8 14 14 12,0 26 42-361B127-R48

Concave face / Spherical button

115 4 1/2 2 8 14 14 9,0 20 42-361B115-S48
121 4 3/4 2 8 14 14 11,0 24 42-361B121-S48
127 5 2 8 14 14 12,0 26 42-361B127-S48
130 5 1/8 2 8 16 13 14,0 31 42-3618130-S48
133 5 1/4 2 8 16 13 15,0 33 42-3618133-S48
Convex face / Ballistic button
110 4 3/8 2 8 14 14 8,0 18 42-365B110-R48
115 4 1/2 2 8 14 14 9,0 20 42-365B115-R48
121 4 3/4 2 8 14 14 11,0 24 42-365B121-R48
127 5 2 8 14 14 12,0 26 42-365B127-R48
130 5 1/8 3 9 16 14 14,0 31 42-36L9130-R48
133 5 1/4 3 9 16 14 15,0 33 42-36L9133-R48
Flat face / Spherical button
110 4 3/8 2 8 14 14 8,0 18 42-36FB110-S48
115 4 1/2 2 8 14 14 9,0 20 42-36FB115-S48
121 4 3/4 2 8 14 14 11,0 24 42-36FB121-S48
127 5 2 8 14 14 12,0 26 42-36FB127-S48
130 5 1/8 2 8 16 14 14,0 31 42-36F9130-S48
133 5 1/4 2 8 16 14 15,0 33 42-36F9133-S48

10 • SANDVIK DTH TOOLS

Sandvik DTH drilling tools
Drill bits with DHD 350 shanks
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
Sandvik RH450 / RH350 mm inch gauge front Kg lb
DHD 350
Concave face / Spherical button DHD 350
130 5 1/8 2 8 16 13 15,0 33 42-6918130-S48
133 5 1/4 2 8 16 13 15,0 33 42-6918133-S48
140 5 1/2 3 9 16 14 16,0 35 42-69D9140-S48
146 5 3/4 2 8 16 14 18,0 40 42-6919146-S48
152 6 2 8 18 16 20,0 44 42-691D152-S48
Convex face / Ballistic button
130 5 1/8 3 9 16 14 15,0 33 42-69L9130-R48
133 5 1/4 3 9 16 16 15,0 33 42-69L9133-R48
140 5 1/2 3 9 16 16 16,0 35 42-69LC140-R48
146 5 3/4 3 9 16 16 18,0 40 42-69LC146-R48
152 6 3 9 18 16 20,0 44 42-69LD152-R48
Flat face / Spherical button
130 5 1/8 2 8 16 14 15,0 33 42-69F9130-S48
133 5 1/4 2 8 16 14 15,0 33 42-69F9133-S48
140 5 1/2 3 9 16 14 16,0 35 42-6929140-S48
146 5 3/4 3 9 16 14 18,0 40 42-6929146-S48
152 6 3 9 18 16 20,0 44 42-692D152-S48

SANDVIK DTH TOOLS • 11

Sandvik DTH drilling tools
Drill bits with DHD 360 & DHD 380 shanks
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
RH450 / RH350 mm inch gauge front Kg lb
DHD 360
Concave face / Spherical button DHD 360
152 6 2 8 18 16 26,0 57 42-731D152-S48
155 6 1/8 2 8 18 16 27,0 60 42-731D155-S48
159 6 1/4 2 8 18 16 30,0 66 42-731D159-S48
165 6 1/2 2 8 18 18 30,0 66 42-73DE165-S48
172 6 3/4 3 9 18 18 31,0 68 42-73DE172-S48
178 7 3 9 18 18 32,0 71 42-73DE178-S48
190 7 1/2 3 9 18 18 34,0 75 42-73DE190-S48
203 8 3 9 18 18 36,0 79 42-73DE203-S48
Convex face / Ballistic button
152 6 3 9 18 16 26,0 57 42-73LD152-R48
155 6 1/8 3 9 18 16 27,0 60 42-73LD155-R48
159 6 1/4 3 9 18 16 30,0 66 42-73LD159-R48
165 6 1/2 3 9 18 18 30,0 66 42-73GE165-R48
172 6 3/4 3 9 18 18 31,0 68 42-73GE172-R48
178 7 3 9 18 18 32,0 71 42-73GE178-R48
203 8 3 9 18 18 36,0 79 42-73GE203-R48
Flat face / Spherical button
152 6 3 9 18 16 26,0 57 42-732D152-S48
155 6 1/8 3 9 18 16 27,0 60 42-732D155-S48
159 6 1/4 3 9 18 16 30,0 66 42-732D159-S48
165 6 1/2 3 9 18 18 30,0 66 42-732E165-S48
172 6 3/4 3 9 18 18 31,0 68 42-732E172-S48
178 7 3 9 18 18 32,0 71 42-732E178-S48
190 7 1/2 3 9 18 18 34,0 75 42-732E190-S48
203 8 3 9 18 18 36,0 79 42-732E203-S48

DHD 380
Concave face / Spherical button DHD 380
200 7 7/8 3 9 18 18 49,2 108 42-87PE200-S48
203 8 3 9 18 18 49,7 110 42-87PE203-S48
216 8 1/2 3 9 18 18 52,0 115 42-87PE216-S48
219 8 5/8 3 9 18 18 52,7 116 42-87PE219-S48
222 8 3/4 3 12 18 18 53,7 118 42-878E222-S48
226 8 7/8 3 12 18 18 54,1 119 42-878E226-S48
241 9 1/2 3 12 18 18 60,1 132 42-878E241-S48
251 9 7/8 3 12 18 18 62,8 138 42-878E251-S48
254 10 3 12 18 18 63,3 140 42-878E254-S48
270 10 5/8 3 12 18 18 71,1 157 42-878E270-S48
305 12 3 12 18 18 84,3 186 42-878E305-S48

12 • SANDVIK DTH TOOLS

Sandvik DTH drilling tools
Drill bits with DHD 112 shanks
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
Sandvik RH450 / RH350 mm inch gauge front Kg lb
DHD 112
Convex face / Spherical button DHD 112
302 11 7/8 3 12 18 18 171,0 377 42-918E302-S48F
311 12 1/4 3 12 18 18 172,0 379 42-918E311-S48F
330 13 3 12 18 18 181,0 399 42-918E330-S48F
357 14 3 18 18 18 191,0 421 42-91PE357-S48F
381 15 3 18 18 18 200,0 441 42-91PE381-S48F
444 17 1/2 3 18 18 18 225,0 496 42-91PE444-S48F
483 19 3 18 18 18 280,0 617 42-91PE483-S48F
508 20 3 18 18 18 306,0 675 42-91PE508-S48F

SANDVIK DTH TOOLS • 13

Sandvik DTH drilling tools
Drill bits with QL 40 shanks
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
Sandvik RH450 / RH350 mm inch gauge front Kg lb
QL 40
Concave face / Spherical button QL 40
115 4 1/2 2 8 14 14 10,0 22 42-431B115-S48
121 4 3/4 2 8 14 14 10,0 22 42-431B121-S48
127 5 2 8 14 14 11,0 24 42-431B127-S48
130 5 1/8 2 8 16 13 11,0 24 42-4318130-S48
133 5 1/4 2 8 16 13 12,0 26 42-4318133-S48
Convex face / Ballistic button
110 4 3/8 2 8 14 14 10,0 22 42-435B110-R48
115 4 1/2 2 8 14 14 10,0 22 42-435B115-R48
121 4 3/4 2 8 14 14 10,0 22 42-435B121-R48
127 5 2 8 14 14 11,0 24 42-435B127-R48
130 5 1/8 3 9 16 14 11,0 24 42-43L9130-R48
133 5 1/4 3 9 16 14 12,0 26 42-43L9133-R48
Flat face / Spherical button
110 4 3/8 2 8 14 14 10,0 22 42-43FB110-S48
115 4 1/2 2 8 14 14 10,0 22 42-43FB115-S48
121 4 3/4 2 8 14 14 10,0 22 42-43FB121-S48
127 5 2 8 14 14 11,0 24 42-43FB127-S48
130 5 1/8 2 8 16 14 11,0 24 42-43F9130-S48
133 5 1/4 2 8 16 14 12,0 26 42-43F9133-S48

14 • SANDVIK DTH TOOLS

Sandvik DTH drilling tools
Drill bits with QL 50 shanks
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
Sandvik RH450 / RH350 mm inch gauge front Kg lb
QL 50
Concave face / Ballistic button QL 50
130 5 1/8 2 8 16 13 14,5 32 42-5518130-R48
133 5 1/4 2 8 16 13 14,5 32 42-5518133-R48
140 5 1/2 2 8 16 14 15,5 34 42-5519140-R48
140 5 1/2 3 9 16 14 15,5 34 42-55D9140-R48
146 5 3/4 2 8 16 14 15,5 34 42-5519146-R48
152 6 2 8 16 16 16,5 36 42-551C152-R48
Concave face / Spherical button
130 5 1/8 2 8 16 13 14,5 32 42-5518130-S48
133 5 1/4 2 8 16 13 14,5 32 42-5518133-S48
140 5 1/2 2 8 16 14 15,5 34 42-5519140-S48
140 5 1/2 3 9 16 14 15,5 34 42-55D9140-S48
146 5 3/4 2 8 16 14 15,5 34 42-5519146-S48
152 6 2 8 18 16 16,5 36 42-551D152-S48
Convex face / Ballistic button
130 5 1/8 3 9 16 14 14,5 32 42-55L9130-R48
133 5 1/4 3 9 16 14 14,5 32 42-55L9133-R48
140 5 1/2 3 9 16 16 15,5 34 42-55LC140-R48
146 5 3/4 3 9 16 16 15,5 34 42-55LC146-R48
152 6 3 9 18 16 16,5 36 42-55LD152-R48
Flat face / Spherical button
130 5 1/8 2 8 16 14 14,5 32 42-55F9130-S48
133 5 1/4 2 8 16 14 14,5 32 42-55F9133-S48
140 5 1/2 3 9 16 14 15,5 34 42-5529140-S48
146 5 3/4 3 9 16 14 15,5 34 42-5529146-S48
152 6 3 9 18 16 16,5 36 42-552D152-S48

SANDVIK DTH TOOLS • 15

Sandvik DTH drilling tools
Drill bits with QL 60 shanks
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
Sandvik RH450 / RH350 mm inch gauge front Kg lb
QL 60
Concave face / Ballistic button QL 60
152 6 2 8 16 16 25,0 55 42-761C152-R48
155 6 1/8 2 8 16 16 26,0 57 42-761C155-R48
159 6 1/4 2 8 16 16 26,0 57 42-761C159-R48
165 6 1/2 3 9 18 18 28,0 62 42-76DE165-R48
172 6 3/4 3 9 18 18 28,0 62 42-76DE172-R48
178 7 3 9 18 18 29,0 64 42-76DE178-R48
190 7 1/2 3 9 18 18 30,0 66 42-76DE190-R48
203 8 3 9 18 18 32,0 71 42-76DE203-R48
Concave face / Spherical button
152 6 2 8 18 16 25,0 55 42-761D152-S48
155 6 1/8 2 8 18 16 26,0 57 42-761D155-S48
159 6 1/4 2 8 18 16 26,0 57 42-761D159-S48
165 6 1/2 2 8 18 16 28,0 62 42-76DD165-S48
165 6 1/2 3 9 18 18 28,0 62 42-76DE165-S48
172 6 3/4 3 9 18 18 28,0 62 42-76DE172-S48
178 7 3 9 18 18 29,0 64 42-76DE178-S48
190 7 1/2 3 9 18 18 30,0 66 42-76DE190-S48
203 8 3 9 18 18 32,0 71 42-76DE203-S48
Convex face / Ballistic button
152 6 3 9 18 16 25,0 55 42-76LD152-R48
155 6 1/8 3 9 18 16 26,0 57 42-76LD155-R48
159 6 1/4 3 9 18 16 26,0 57 42-76LD159-R48
165 6 1/2 3 9 18 18 28,0 62 42-76GE165-R48
172 6 3/4 3 9 18 18 28,0 62 42-76GE172-R48
178 7 3 9 18 18 29,0 64 42-76GE178-R48
203 8 3 9 18 18 32,0 71 42-76GE203-R48
Flat face / Spherical button
152 6 3 9 18 16 25,0 55 42-762D152-S48
155 6 1/8 3 9 18 16 26,0 57 42-762D155-S48
159 6 1/4 3 9 18 16 26,0 57 42-762D159-S48
165 6 1/2 3 9 18 18 28,0 62 42-762E165-S48
172 6 3/4 3 9 18 18 28,0 62 42-762E172-S48
178 7 3 9 18 18 29,0 64 42-762E178-S48
190 7 1/2 3 9 18 18 30,0 66 42-762E190-S48
203 8 3 9 18 18 32,0 71 42-762E203-S48

16 • SANDVIK DTH TOOLS

Sandvik DTH drilling tools
Drill bits with QL 80 shanks
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
Sandvik RH450 / RH350 mm inch gauge front Kg lb
QL 80
Concave face / Spherical button QL 80
200 7 7/8 3 9 18 18 49,9 110 42-83PE200-S48
203 8 3 9 18 18 50,4 111 42-83PE203-S48
216 8 1/2 3 9 18 18 52,7 116 42-83PE216-S48
219 8 5/8 3 9 18 18 53,4 118 42-83PE219-S48
222 8 3/4 3 12 18 18 54,4 120 42-838E222-S48
226 8 7/8 3 12 18 18 54,8 121 42-838E226-S48
229 9 3 12 18 18 55,2 122 42-838E229-S48
241 9 1/2 3 12 18 18 60,8 134 42-838E241-S48
251 9 7/8 3 12 18 18 63,5 140 42-838E251-S48
254 10 3 12 18 18 64,0 141 42-838E254-S48
270 10 5/8 3 12 18 18 71,8 158 42-838E270-S48
305 12 3 12 18 18 85,0 187 42-838E305-S48
Convex face / Ballistic button
203 8 3 9 18 18 51,3 113 42-83GE203-R48
216 8 1/2 3 9 18 18 53,6 118 42-83GE216-R48
222 8 3/4 3 12 18 18 55,2 122 42-83CE222-R48

Flat face / Spherical button

203 8 3 9 18 18 51,0 112 42-832E203-S48
216 8 1/2 3 9 18 18 53,7 118 42-832216-S48
222 8 3/4 3 12 18 18 55,4 122 42-83KE222-S48
229 9 3 12 18 18 56,8 125 42-83KE229-S48

SANDVIK DTH TOOLS • 17

Sandvik DTH drilling tools
Drill bits with SD 10 & SD 12 shanks
Optional for Sandvik hammers: Diameter Air Gauge Button dia. mm Weight Part No. Shank
holes buttons
Sandvik RH350 mm inch gauge front Kg lb
SD 10
Concave face / Spherical button SD 10
254 10 3 12 18 18 108,0 238 42-108E254-S48F
270 10 5/8 3 12 18 18 108,0 238 42-108E270-S48F
279 11 3 12 18 18 113,0 249 42-108E279-S48F
305 12 3 12 18 18 125,0 276 42-108E305-S48F

SD 12
Concave face / Spherical button SD 12
302 11 7/8 3 12 18 18 171,0 377 42-128E302-S48F
311 12 1/4 3 12 18 18 172,0 379 42-128E311-S48F
330 13 3 12 18 18 181,0 399 42-128E330-S48F
357 14 3 18 18 18 191,0 421 42-12PE357-S48F
381 15 3 18 18 18 200,0 441 42-12PE381-S48F
444 17 1/2 3 18 18 18 225,0 496 42-12PE444-S48F
483 19 3 18 18 18 280,0 617 42-12PE483-S48F
508 20 3 18 18 18 306,0 675 42-12PE508-S48F

18 • SANDVIK DTH TOOLS

DTH Drilling Products

TUBEX XL Systems

Casing shoe
Discharge head Steel casing
Guide device Reamer
Drill pipe Guide sleeve Pilot bit
Hammer

4-1/134/XL

TUBEX XL Product Range

TUBEX XL Casing, recom. size, mm Min. wall Max. drill Reaming
Type thickness, bit diameter, diameter, OD
Max. OD Min. ID mm mm A mm

90 115 102 5 90 123 ID

115 142 128 5 115 152

140 171 157 5 140 187

A
165 196 183 5,5 165 212

180 219 194 6,3 180 232

190 222 205 6,3 190 237

215 257 241 6,3 215 278

230 270 250 6,3 230 286

240 273 260 6,3 240 306

280 327 305 7,1 280 370

System Part Description Weight Part Number

kg lb

TUBEX XL-90 Guide Devices M30 7 16 80-3A00-090D

IR 3.5 ( Foot Valve, 47-24017 ) 7 16 80-2400-090D

Pilot Bit 1/8, 12/12, CV, DP65 3,6 7.9 81-090B-090A65

Eccentric Reamer 1,4 3.0 82-090B-123W65

Casing Shoe 1,1 2.4 84-090D-00

Stabilizer 2 3/8" Box & Pin API Reg.; wrench flat - 65mm 6 13 7989-2999

Locking Kit 85-090-KT

DTH Drilling Products

System Part Description Weight Part Number

kg lb

TUBEX XL-115 Guide Devices M40 12 27 80-4800-115D

IR 340 ( Foot Valve, 47-36017 ) 12 27 80-3600-115D
QL 40 ( Foot Valve, 47-43017 ) 12 27 80-4300-115D
COP 42 ( Foot Valve, 47-37017 ) 12 27 80-3700-115D

Pilot bit 2/8, 14/14, CV, DP65 8 17 81-115A-115A65

Eccentric reamer 2,6 5.7 82-115A-152W65

Eccentric reamer 2,6 5.7 82-115B-152A65

Casing shoe 1,6 3.5 84-115D-00

Stabilizer wrench flat 65mm, 2 3/8" Box & Pin API Reg. 8,3 18.3 7989-1627

Locking Kit 85-115A-KT

TUBEX XL-140 Guide devices M50 22 49 80-5800-140D

SD 5 (Foot Valve, 47-51017) 21 45 80-5100-140D
IR DHD 350R (Foot Valve, 47-69037) 21 45 80-6900-140D
QL 5 (Foot Valve, 47-55037) 21 45 80-5500-140D

Pilot bit 2/8, 14/14, CV, DP65 11 24 81-140A-140A65

Eccentric reamer wear-protection buttons, 189mm reaming dia. 4 9 82-140A-189W65

Eccentric reamer wear-protection buttons, 197mm reaming dia. 4 9 82-140A-197W65

Casing shoe 2,4 5.3 84-140D-00

Stabilizers wrench flat 65mm, 2 3/8" API Reg. 9 19.8 7989-1451

wrench flat 95mm, 3 1/2" API Reg. 16,4 36.1 7989-1452

Locking Kit 0,5 1 85-140A-KT

TUBEX XL-165 Guide devices M 60/60W 34 74 80-6800-165D

SD 6 ( Foot Valve, 47-61017 ) 36 79 80-6100-165D
IR 360 ( Foot Valve, 47-73017 ) 34 74 80-7300-165D
QL 60 ( Foot Valve, 47-76017 ) 34 74 80-7600-165D

Pilot bit 2/8, 16/16, CV, DP65 17 38 81-165A-165A65

Eccentric reamer 7 15 82-165A-212W65

Casing shoe 3,2 7 84-165D-00

Stabilizer Wrench flat is 95mm, 31/2" API Reg. Box & Pin 22 47 7989-1777

Locking Kit 85-165A-KT

DTH Drilling Products

System Part Description Weight Part Number

kg lb

TUBEX XL-180 Guide Devices SD 6 ( Foot Valve, 47-61017) 44 97 80-6100-180D

IR 360 ( Foot Valve, 47-73017 ) 44 97 80-7300-180D

Pilot Bit 2/8, 16/16, CV, DP65 24 52 81-180A-180A65

Eccentric Reamer 10 22 82-180A-232W65

Casing Shoe 4 9 84-180D-00

Stabilizer API 31/2" API Reg. Box & Pin 25 55 7989-2389

Locking Kit 85-180A-KT

TUBEX XL-190 Guide Devices M60 40 88 80-6800-190D

SD 6 ( Foot Valve, 47-61017) 44 97 80-6100-190D
SD 8 ( Foot Valve, 47-81017) 47 103 80-8100-190D
QL 6 ( Foot Valve, 47-76017 ) 44 97 80-7600-190D
IR 360 ( Foot Valve, 47-73017 ) 44 97 80-7300-190D

Pilot Bit 3/8, 16/16, CV, DP65 29 64 81-190A-190A65

Eccentric Reamer 10 22 82-190A-237W65

Casing Shoe 4,1 9 84-190D-00

Stabilizer API 31/2" API Reg. Box & Pin 25 55 7989-3100

Locking Kit 85-190A-KT

TUBEX XL-240 Guide Devices

SD 8 (Foot Valve, 47-81017) 67 148 80-8100-240D
IR 380 (Foot Valve, 47-81017) 67 148 80-8700-240D

Pilot Bit 2/12, 16/16, CV, DP65 46 102 81-240B-240A65

Eccentric Reamer 18 39 82-240B-308W65

Casing Shoe 7 15 84-240A-00

Stabilizer 41/2" API Reg. Box & Pin, 114mm wrench flat 40 89 7989-2255

Locking Kit 1,5 3.3 85-240A-KT

TUBEX XL-280 Guide Devices SD 10 (Foot Valve, 47-10017) 160 353 80-1000-280A

Pilot Bit 3/12, 18/18, CV, DP65 88 194 81-280A-280A65

Eccentric Reamer 43 95 82-280A-378W65

Casing Shoe 15 33 84-280A-00

Locking Kit 1,5 3.3 85-280A-KT

DTH Drilling Products

Information in this catalogue is subject to change without notice. Please confirm part numbers before ordering.
Product updates may be found at Sandvik's web site: www.sandvik.com

The remainder of this page is left blank for your notations.

 www.sandvik.com

Sandvik Mining and Construction Tools AB

SE-811 81 Sandviken, Sweden. Tel +46 26 26 20 00 Fax +46 26 26 23 00