See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/327230747

INTERNATIONAL JOURNAL OF RESEARCH IN ELECTRONICS AND COMPUTER

ENGINEERING A UNIT OF I2OR Simulation and Implementation of An
Automatic Battery Charger using Silicon Control Rectifi...

Article · August 2018

CITATIONS
READS
0
968

3 authors, including:

Ramzi Abdul-Halem
University of Nizwa
7 PUBLICATIONS 1 CITATION

SEE PROFILE

Some of the authors of this publication are also working on these related projects:

DC to DC buck boost converters View project

SCR Firing Circuit, Design, Simulation and Implementation View project

All content following this page was uploaded by Ramzi Abdul-Halem on 26 August 2018.

The user has requested enhancement of the downloaded file.

IJRECE VOL. 6 ISSUE 3 ( JULY - SEPTEMBER ISSN: 2393-9028 (PRINT) | ISSN: 2348-2281
2018) (ONLINE)
Simulation and Implementation of An Automatic Battery
Charger using Silicon Control Rectifier (SCR)
Eman M. Al-Siyabi, Gaflah K. Al-Mahrami, Ramzi A. Abdul-Halem
Nizwa University, College of Engineering, Department of Electrical and Computer Engineering,
Nizwa, Sultanate of Oman

ABSTRACT-Batteries provide the technologies is making headways into the industrial battery
closekeyforstoringelectricity by putting away electrical energy charger markets over ferroresonant and SCR types.[3]
in form of chemical energy. This paper deals with a partial
After fully charging the battery of the suggested charger by
design, simulation and implementation of an automatic battery
means of a main SCR, charger changes automatically to
chargerusing SCRs. Depending on the charging process
discharge sequence through another auxiliary SCR and vise-
requirements some elements of the electronic circuit will be
versa.The output DC voltage can be regulated depending on
designed. The designed circuit will be simulated using
the load specifications.
MULTISIM, thenimplementedusing an experimental setup
builds in the laboratoryfor verification. The charging
progression and the fully charging process realize completely
using two SCRs, main and auxiliary. Simulation results and METHODOLOGY
experimental results will be represented and compared. SYSTEM DESCRIPTION
Keywords: Automatic battery charger, Simulation,  Block Diagram of battery charger using SCRs
Implementation, Controlled-rectifier, SCR
In this work, the illustrative block diagram of the battery
charger using SCRs is shown in figure 1. Clearly, the diagram
INTRODUCTION enclosesfundamentally an AC voltage source, single-phase
transformer, bridge rectifier, voltage regulator, SCR and
Battery chargeris a device used to store energy into a chargeable battery. In the following sections, the operation of
secondary cell or rechargeable battery by forcing an electric the suggested charger using SCR will be described.[4]
current through it.The charging protocol depends on the size
and type of the battery being charged. Some battery types have
high tolerance for overcharging and can be recharged by
connection to a constant voltage source or a constant current
source, depending on battery type. Simple chargers of this
type must be manually disconnected at the end of the charge
cycle, and some battery types absolutely require, or may use a
timer, to cut off charging current at some fixed time, Figure 1: Block diagram of the battery charger using
approximately when charging is completed. Other battery SCRs
types cannot withstand over-charging, being damaged, over
heating or even exploding. The charger may have temperature  Battery charger circuit with two SCRs
or voltage sensing circuits and a microprocessor controller to
The electronic circuit of the automatic battery charger
safely adjust the charging current and voltage, determine the
circuit using SCRs is partially designed, simulated and
state of charge, and cut off at the end of charge. [1][2]
implemented. The circuit can be used to charge batteries with
Battery charging is a complex electrochemical process, in different level of voltages, for instant, 6V, 9V or 12V in
which the discharged electric energymust be refilled from the choosing appropriate components. As well as, it can be used to
electric network. The quality of the charging process is critical power-driven low power loads such as, cell phone, camera,
tothe condition and long life of batteries. A battery charger is etc. The circuit operation can be illustrated as follows:
an electrical/electronic device that converts the incoming AC
line voltageinto a regulated DC voltage to meet the  Simulation of the charger
changingneeds of the respective battery.Although today’s The simulated circuit as shown in figure 2, contains in
industrial battery charging market is dominated by addition to the main and auxiliary SCR’s, two LED's, and
ferroresonant and SCR type chargers, which have been in many other electronics and power components such, single-
existence for many years, new high frequency battery charging phase transformer, single-phase full-wave diode rectifier,
voltage regulator, rechargeable battery, diodes , capacitors, auxiliary SCR (D2) uses to indicate the ending of the charging
and resistors. Each of the pointed out components has its role
process and the fully charging of the battery. The LED in the
in the operation of the circuit as it will be illustrated. The main
two cases uses to indicate the operation period of the two
SCR (D1) uses in the charging process and the second
SCR's respectively.[5][6]

INTERNATIONAL JOURNAL OF RESEARCH IN ELECTRONICS AND COMPUTER ENGINEERING

A UNIT OF I2OR 1070 | P a g e
IJRECE VOL. 6 ISSUE 3 ( JULY - SEPTEMBER ISSN: 2393-9028 (PRINT) | ISSN: 2348-2281
2018) (ONLINE)

Figure 2: Diagram of the simulated circuit

The battery charger elements are listed in Table 1.
Table 1: Elements used in Battery charger circuit with two SCRs:
NO Component’s Name Component’s Type Value or code
1 Voltage source AC voltage source 240V(rams), 50HZ
2 Transformer Step down transformer 240/14 V
3 Battery charger Lead acid battery charger 12V
4 Diode 1, D1 Silicon controlled rectifier BT149-B
5 Diode 2, D2 Silicon controlled rectifier BT149-B
6 Diode3, D3 Zener diode 1N4462
7 Diode4, D4 Single Standard Switching Diode 1N4002
8 Bridge rectifier, D5 Full wave rectifier 1B4B42
9 Voltage regulator IC LM7815CT
10 Capacitor ,C1 Aluminum electrolytic capacitor 100 uF
11 Capacitor, C2 Ceramic 100 nF
12 Capacitor , C3 Ceramic 100 nF
13 Resistor 1, R1 Ceramic 1.2 kΩ
14 Resistor 2, R2 Ceramic 560Ω
15 Resistor 3, R3 Ceramic 1.5 KΩ
16 Resistor 4, R4 Ceramic 10 kΩ
17 Resistor 5, R5 Potentiometer 10 kΩ
18 Resistor 6, R6 Ceramic 2.2KΩ
19 LED1 Green LED -
20 LED2 Red LED -

INTERNATIONAL JOURNAL OF RESEARCH IN ELECTRONICS AND COMPUTER ENGINEERING

A UNIT OF I2OR 1071 | P a g e
  Operation of the charger
The circuit operation starts in supplying 240 V from AC voltage source to the circuit passing through a single-phase
transformer 240/14 V and a single-phase full-wave diode rectifier to rectify the AC-to-DC voltage that is needed for battery
charging. By the way, the capacitors C1-C3 use for DC voltage smoothing and the voltage regulator uses for controlling the output
DC voltage at a value of 15 V as show in figure 3 that is appropriate for charging process.Initially, the main SCR 1, (D1) starts
conducting at the instant of receiving the required gating signal through R 2 and D4. In the conducting period, green LED1 which is
connected in series turns ON, to ensure the starting period of battery charging.During this period the output of the voltage
regulator, 15V DC will apply across the serial combination of (D1, resistor R1 =180Ω, and the battery to be charged). The
charging current will flow through the battery and the charging process will start till the fully charging of the battery
approximately equal to 12 V. At this instant, the charging current will be less than the holding current, IH which is the
minimumneeded current to keep the SCR in its On-state and the conduction will be ended and the SCR1state will be changed to
Off-state.When the main SCR1 stops conducting and the battery is fully charged, the auxiliary SCR 2 conducting period is started
at the instant of the battery 12 V applied across the combination of R3and R5 and a current will flow through this combination and
a part of the voltage across the variable resistor of 10 kΩ, reaches to a value of 7.5 V that is necessary for letting the Zener diode
(D3) to be in On-state and a triggering gating current by applied to SCR2 (D2) changing its state from Off to On-state, and the red
LED2 which is connected in series with SCR2 (D2) will be in the On-state indicating the ending of the charging period.

Figure 3: Input and output voltage of the voltage regulator

 Output of the charger
Simulation tests were performed using MULTISIM. From the reading of the meters in figure 4, it is clear that during charging
process, with abattery voltage of value 5 V, the current flow through the Thyristor SCR 1 has a value of 38.926 mA and through
the second Thyristor SCR2 is 6.523 uA (very small), which mean that the SCR 1 is in On-state and the SCR 2 is in Off-state. While
at the fully charging process, and at a value of battery voltage equal to 12 V, it is clear from figure 5 that the current value through
the Thyristor SCR1 is 1.248 mA (smaller than that in the charging process) and through the second Thyristor SCR 2 is 66.955 mA
(much larger than that in the charging process). Which means that the SCR1 is in off- state while the SCR2 is in On- state.
 Figure 4: The current values at charging process

Figure 5: The current values at fully charging process

 From figure 6,the potentiometer voltageat charging process is 3.695 V which is not enough for turning on the Zener diode and
the SCR2 is not triggering so it stays in Off- state and red LED is Off. While at the fully charging period, the voltage at the
potentiometer is reached to 8.064 V which is enough for letting the Zener diode to be in On-state and letting current flows to the
SCR2 and turn it On and at the same time, turning the red LED on as shown in figure 7.

Figure 6: The potentiometer voltage at charging process

Figure 7: The potentiometer voltage at fully charge process

 EXPERIMENTAL SETUP, RESULTS AND DISCUSSION
The electronic circuit is built in the laboratory as shown in figure 8.

Figure 8: Experimental set up of the project

When the circuit connects to the AC power supply, as shown in figure 9 the necessary getting current for SCR1 triggering it
and its state changes to ON indicating the starting of the charging period. At the same time, the green LED becomes ON
indicating the starting of charging period and the charging current flows to the battery for charging.

Figure 9: The charging process

After 7 to 8 hours, the SCR 1 automatically stops conducting and becomes in Off-state. While the SCR 2 starts conducting after
triggering by the Zener diode by which the charging process is stopped and the red LED is turning ON as shown in figure 10.
IJRECE VOL. 6 ISSUE 3 ( JULY - SEPTEMBER ISSN: 2393-9028 (PRINT) | ISSN: 2348-2281
2018) (ONLINE)

Figure 10: Fully charging process

CONCLUSSION
The paper presentedan automatic battery charger using two SCRs, main for charging course and auxiliary for discharge
course. Depending on the charging process requirement some electronic elements of the charger have been designed. The
designed circuit has been simulated using MULTISIM, constructed in the laboratory and then tested for verification. The
simulated and experimental results were compared and they found to be in match and satisfy the main goal of the suggested
charger

REFERENCES
1. ^"Recharger definition and meaning - Collins English Dictionary". Retrieved 26 March 2017.
2. ^"recharge - definition of recharge in English - Oxford Dictionaries". Retrieved 26 March 2017.
3. https://act-chargers.com/wp-content/uploads/2017/03/ACT-White-Paper-Battery-Charging-Technology-Overview.pdf
4. http://www.idc- online.com/technical_references/pdfs/electronic_engineering/Battery%20Charger%20Circuit
%20Using%20SCR.pdf
5. http://eie.uonbi.ac.ke/sites/default/files/cae/engineering/eie/AN%20SCR%20CONTROLLED%20BATTERY%20CHARGE
R.pdf
6. http://academic.cankaya.edu.tr/~saltay/melike_ali_rapor97.pdf

INTERNATIONAL JOURNAL OF RESEARCH IN ELECTRONICS AND COMPUTER ENGINEERING

A UNIT OF I2OR 1076 | P a g e

View publication stats