VAC-COM FUNCTION CODING ON

SKODA OCTAVIA A7 / A7FL

version 1.110.7 dated 01/27/2019

FAQ (INSTRUCTION)

Q: WHAT IS NECESSARY TO USE CODING DATA?

A: Car, VAG-COM cord, VCDS program or Vasya diagnostician, working brains and straight arms (or a friend with all this).

Q: WILL THE CODES DESCRIBED HERE FIT OTHER VAG CARS?

A: Possibly. Blocks on cars of the VAG family are often used the same, however, the physically installed equipment may differ. You can try at your own peril
and risk.

Q: WHY ARE NOT ALL CODES FOR THE OCTAVIA A7 HERE?

A: There are exactly two options: 1 - some encoding was unknown at the time the file was created ( inform please, about her); 2 - only encodings are
indicated here, which do not require the installation of additional equipment. As a rule, the instructions for installing additional equipment contain
coding for its connection and configuration. Perhaps, the file will soon be supplemented with such encodings, but for now it is a kind of Lite version.

Q: THESE CODES HAVE A DIFFERENT NAME ON THE INTERNET, WHY?

A: Because the names in the primary sources were often given in a hurry to celebrate the discovery. Here I tried to name things (encodings,
systems, functions) by their correct names. If something goes wrong, we are all human - correct ...

Q: WHY DO I NEED THE SECTION "BASICS", IN FACT I KNOW EVERYTHING, AND TO PRINT AN EXTRA 5 SHEETS?
A: Of course, this information will be superfluous for a real professional, but this file itself is unlikely to be useful to him (for sure there are some
developments). The rest, as in assembling IKEA furniture, may not read the "Basics" and immediately get to work. When the question arises “why am I
missing a bit?”, Or “I cannot understand what block I have,” then the separator may be useful!

Q: I HAVE AN ENGLISH VERSION OF THE SOFTWARE AND IT'S NOT CLEAR IN WHICH BLOCK TO GO IN WHICH ITEM TO CHOOSE.

A: Translator to help you. You can also look at screenshots of points 2 and 3 Error! The link source was not found. - there are numbers for each block and
item, which remain the same in different versions of the program. In general, it is better to get hold of the Russian-language version of the program, ideally
the licensed "Vasya diagnostician"!

Q: CAN I USE THIS FILE FOR COMMERCIAL PURPOSES?

A: Everyone has their own karma, everyone decides for himself. All information specified in this file was obtained free of charge and this file is also
distributed free of charge.

Q: WHAT DOES THE VERSION OF THIS FILE MEAN?

A: The first digit changes when there are fundamental changes, the second shows how many encodings are in the file, the third changes when you make
slight linguistic and spelling changes. You need to download the current version only if there are changes in the first two digits.

A RESPONSIBILITY
Everything that you do, you do at your own peril and risk! According to available information from OD, the guarantee rules have been tightened. All OD
received the official TPI from the technical support service for installing any special stages and activating various functions. In which it is said that even
with the harmless activation of "Corner" and the installation of diode lamps, not to mention more serious modifications, OD has the right to refuse
warranty repair of the car's electrical equipment.

Be extremely careful!

one
CONTENT
Introduction & access codes five
one. Control and dynamics 6
1.1 DSR activation / adaptation 6
1.2 Extended ESС function 6
1.3 ESC Sport / ESC Off 6
1.4 Auto enable ESC (over 100 km / h ) 6
1.5 ESC menu 7
1.6 Configuring ASR 7
1.7 TSC activation 7
1.8 Activating / configuring HHC 7
1.9 Indirect TPMS Activation eight

1.10 Bdw adaptation eight

1.11 Activating / Configuring XDS eight

1.12 Deactivation of the "Start-stop" system nine

1.13 Reconfiguring the gas pedal nine
1.14 Elimination of "bluntness" of the gas nine
1.15 pedal Adaptation Brake Assist nine

2. Shine 10
2.1 Turning on the rear dimensions in the DRL mode Turning off the DRL in 10
2.2 the "0" mode when lifting the handbrake Turning off the DRL through 10
2.3 the menu 10
2.4 Parking lights operating mode 10
2.5 "Polite turn signal" 10
2.6 Setting the threshold for the response speed eleven

2.7 FLA LEDs in the room backlight eleven

2.8 LEDs in leg lighting CH eleven

2.9 activation eleven

2.10 CH / LH menu 12
2.11 CH / LH source setting 12
2.12 Corner activation 12
2.13 On / off Corner depending on the speed 13
2.14 Activation of the second (right) rear PTF 13
2.15 Stroboscope (DRL (halogen) + far + turn signals) 13
2.16 Stroboscope (far + PTF) fourteen

2.17 Stroboscope (far + DRL) PTF fourteen

2.18 activation together with DRL fourteen

2.19 DRL activation together with low beam fourteen

2.20 Disabling the front dimensions only when the dipped beam is on. The fifteen

2.21 brightness of the front dimensions as DRL fifteen

2.22 Activation of inclusion of rear PTF together with brakes fifteen

2.23 The inclusion of front turn signals (American var) together with the dimensions. fifteen

2.24 Turning on the front turn signals (American var) instead of dimensions Winking sixteen

2.25 reversing lamps with turn signals when turning on the reverse speed and
emergency gang sixteen

2.26 Activation of the front PTFs when reverse gear is engaged 17

2.27 Increase the brightness of the reverse lamps 17
2.28 Increasing the brightness of the headlight lamps 17
2.29 Increasing the brightness of the PTF lamps 17
2.30 Emergency braking alarm LED rear 17
2.31 lights 17
2.32 Dimming / winking / simultaneous operation of LED DRL

2
 Turning on the direction indicators (Audi Style) Turning off the interior twenty

2.33 lights when opening the trunk Turning off the license plate light when 21
2.34 opening the trunk Adjusting the brightness of the instrument in any 21
2.35 light 21

3. Comfort 24
3.1 Disable seat belt alert 24
3.2 Turning off the notification about the ignition on when opening the door 24
3.3 Activating the notification about the left ignition key 24
3.4 Storing the last seat heating level Seat heating 24
3.5 adaptation 24
3.6 Easy Entry Activation 25
3.7 Activating AUTO steering wheel heating 25
3.8 Climate fan speed display in AUTO Climate 25
3.9 recirculation memory activation 25
3.10 Auto recirculation of the stove after turning off the ignition 25
3.11 Memorizing the setting of the recirculation of the stove after turning off the 26
3.12 ignition. 26
3.13 Reduced fogging of windows outside at high humidity 26
3.14 Increased heating time for the rear window 26
3.15 Increasing the heating time of the windshield Tilting the right mirror when 26
3.16 reversing Turning on the illumination of the mirrors when reversing Folding / 26
3.17 unfolding the side mirrors by holding the door key button or when the 26
3.18 ignition is turned on
27
3.19 Operation of power windows when the ignition is off Closing the 27
3.20 windows in the rain 27
3.21 Highway mode 28
3.22 Service position menu 28
3.23 Service position of wipers 28
3.24 Wiping drops with front wipers Wiping 28
3.25 drops with rear wipers 29
3.26 Rear wiper working interval adaptation 29
3.27 Automatic rear wiper activation 29
3.28 Increasing the interval between the operation of the headlamp washers 29
3.29 Completely deactivating the headlamp washers 29
3.30 Locking the doors at a speed of 15 km / h and unlocking them when removing the key from the
lock thirty

3.31 Convenient door closing thirty

3.32 Activation of the key fob when the engine is running Activation of thirty

3.33 the door sensors when the engine is running Sound thirty

3.34 accompaniment of opening / closing with a standard key Turning thirty

3.35 on light / sound alarm 31

3.36 Activation of opening the electric door from the salon / 31
3.37 from the key Locking the tailgate 31
3.38 MKE Activation 31

four. Other functions 32

4.1 Shooters test 32
4.2 Deactivation of the sound message about the ignition on when opening the door Display 32
4.3 of the battery status in the on-board computer 32
4.4 Start-up screensaver of the radio + image of the car 32
4.5 Changing the skin of the radio and tidy 32
4.6 Driving School Mode 33

3
 4.7 Deactivation of the AM range in the radio Activation 33
4.8 of Skoda surround + virtual subwoofer Developer 33
4.9 mode + sound enhancement 33
4.10 Improving the sound of the built-in radio 34
4.11 Activating the rear speakers 35
4.12 Activates the low frequency analogue input AUX-IN 35
4.13 Activates the USB input 35
4.14 Rear view camera activation 36
4.15 Green Drive display 36
4.16 Off Road Display 36
4.17 TMC activation 36
4.18 Adapting microphone sensitivity 36
4.19 120km / h warning 37
4.20 Time format - 12h or 24h Set 37
4.21 maintenance interval 37
4.22 Speed limit signs 37
4.23 Lap timer 37
4.24 Free space in the tank Installing the 37
4.25 multifunction steering wheel 38

Respect 39

four
INTRODUCTION & ACCESS CODES

Do not forget to make backups or screenshots (as it was before transcoding) !!!

Description of blocks:
• Block 01 Engine
• Block 03 ABS / ESP
• Block 09 BCM
• Block 10 Parking system
• Block 13 Auto-Distance
• Block 17 Instrument panel
• Block 18 Autonomous heater
• Block 19
• Block 20
• Block 44 Steering booster
• Block 75
• Block 52 Passenger door electronics
• Block 5F MMI / RNS
• Block 6D Trunk electric drive Block 65
• Tire pressure with sensors Block A5
• Front chamber

Block logins:
• Block 01 - 27971
• Block 03 - 20103, 40168, 11966, 25004, 40304 (for BDW - brake disc drying), 15081, 32304, 33776,
33777, 33799, 37201, 37202, 37203, 37483, 24990, 25327, 25377, 25757, 31857, 10815, 11122, 14108, 14451,
24435, 12345 IMPORTANT depending on the adaptations being changed, login Block 09 -
• 31347, 03147?
• Block 10 - 71679
• Block 13 - 14117
• Block 17 - 20103, 25327, 40168, for new ones try 12345 Block
• 18 - 80782
• Block 19 - 20103
• Block 20 - 89687
• Block 42 - 20103
• Block 44 - 19249, 17580
• Block 75 - 20103
• Block 52 - 20103
• Block 5F - 20103, 25327, 12345 (40168)
• Block 6D - 12345
• Block 65 - 20103
• Block A5 - 20103

The numbering of bytes, bits starts from zero! 0

byte, 1 byte…. 29 bytes
0 bit, 1 bit ... 7 bit
Bits can be manually set to "1" for the enabled bit for binary code (from the end). For example: 00000001
is the on bit "0"
00000010 is the included bit "1"

five
1. CONTROL AND DYNAMICS

1.1 Activation / adaptation of DSR

Features of the
Activation and adaptation of DSR allows you to adjust the dynamic change in steering effort depending on the vehicle speed.
"Characteristic curve of steering assistance" has 5 values:
• Driver profile ...,
• Comfort (when driving slowly, the steering wheel is light, as you accelerate the steering wheel becomes heavier) Automatic

•
• Dynamic (always remains heavy)
• Default
Driving Profile switchover has 2 meanings:
• direct (step, steer on a threshold, bring the rudder back to zero faster) incremental (step, steer on time, return
• the rudder over time)
Direct, unlike incremental, returns the steering wheel to its original position (straight ahead) when cornering, this effect is especially felt in low speed maneuvers.

This is an incorrect description! As it turned out:

1) "Characteristic curve of steering assistance" - here the general "gain" / "relief" of the steering wheel is set.
2) "Driving Profile switchover" - here the "logic" of amplification is selected. direct - always the same as selected in the first paragraph; incremental - at low speeds it is easier, at higher speeds it becomes
heavier (and how much heavier it is, is selected in the first paragraph).

Encoding:
Block 44 → login-password 19249 → coding long encoder → Byte 0 → enable Bit 7 (from 01, now 81) Block 44 →
adaptation →
• Characteristic curve of steering assistance → select the desired value → save

• Driving Profile switchover → select the desired value → save

Notes (edit)
Who loves a light steering wheel - Comfort and incremental
Who loves an active driving profile - Dynamic and Direct

1.2 Extended ESС function

Features of the
Extended Electronic Stability Program (ESC) function
Encoding:
Block 03 → adaptation 10 → channel
MAS00122-Electronic stability control system → activate

1.3 ESC Sport / ESC Off

Features of the
the ability to limit or disable the ESC system - ESC Sport / ESC Off
ATTENTION! To activate, you must have an ABS block with 30 byte coding.

Encoding:
Block 03 → coding long encoder → Byte 29 • bit 1, bit 2 • enable
- value = 06 (for Swing) Byte 29 • bit 0, bit 3 • enable - value = 09
(for Bolero) or

03 block - Long coding - Byte 29, bits 0 and 2 on, bits 1 and 3 off.

1.4 Auto enable ESC (over 100 km / h)

Features of the
Activation of automatic activation of ESC upon reaching the speed of 100 km / h, if it was deactivated

Encoding:
03 block → Login 20103 → Adaptations → Channel "Activation depending on speed" → enable!
if you don't want ESP to turn on back at speeds above 100 km / h

6
Block 03 → adaptation → ESP activation depending on speed (Electronic stabilitin program) → deactivate → save

Note
I did not find this channel for myself

1.5 ESC menu

Features of the
ATTENTION! To activate, you must have an ABS block with 30 byte coding.
ATTENTION! on machines of 2016-17, it is possible to install 31-byte ABS blocks, and so there is the last byte, usually there is a value of 03, so you don't need to touch it !!!

Encoding:
For ABS units with 30 byte coding
Block 03 -> coding long encoder -> byte 29 • bit 0, bit 2 • enable (value = 05, which for Swing, gives the ESC menu
with the following items - ESC On, ASR Off, ESC Off)
Can be replaced with the following values:
• 05 —ESC On / Off + ASR Off 06
• - ESC On / Off + ESC Sport 07
• - ESC On / Off + ASR Off 08
• - ESC On / Off + ESC Sport
• 09 —ESC On + ASR Off + ESC Sport

For ABS units with 29 byte coding

25 bytes in it are standard 2A encoding, change it to 3A press Enter
Note
The values 05 or 07 and 06 or 08 depend on the ABS unit. Also the default was 02.

1.6 Configuring ASR

Features of the
Adaptation of ASR (vibration reduction system at start), selection of the system response threshold at the start - there are 3 values:
• Normal (less cutting),
• Strong (default),
• Maximum (for those who do not want to wash the rubber, but the system chokes the engine),

Encoding
Block 03 → login-password 20103 → adaptation → IDE05337-Starting vibration reduction → select the desired value →
save

1.7 Activating TSC

Description
TSC - Torque Compensation, Lane Control Assistant. This function allows you to exclude, and at some points to minimize the steering to the right with sharp acceleration.
Acts at a sharp increase in speed and does not allow the machine to deviate from the straight-line movement.
Features of the
There are 3 meanings:
- 00-Torgue Steer Compensation (TSC) inactive,
- 04- Torgue Steer Compensation (TSC) with learned Value active - recommended,
- 08-Torgue Steer Compensation (TSC) without learned Value active.
Important !!! When coding with a Chinese string, most likely the list of these 3 values will not be available, so we turn on the desired bit 2 this is 04-value or bit 3 gives 08-value, off
bit 2, bit 3 gives 00- value.
Encoding
Block 44 → login-password 19249 → coding-long coding → Byte 0 → enable Bit 2 or Bit 3
Notes (edit)
In the process of changing block 44, it will swear at ESC, tire pressure monitoring. Clear errors in block 03, and in block 01.

1.8 Activating / Configuring HHC

Description
HHC (Hill Hold Control) - holding the car at the beginning of the movement when descending or ascending a slope until the driver presses the gas pedal.
This hill start assist allows you to move your foot from the brake pedal to the accelerator pedal when starting up hill without holding the car with the parking brake. The
systemmaintains the pressure in the brake system for 2 seconds after releasing the brake pedal and is activated on inclines steeper than 5%, provided that the driver's door is
closed, only when starting off on an incline, both when moving forward and when reversing.

7
There are 3 meanings:
- early (early),
- normal,
- late.
Features of the
Tested on 30 bytes (MK100ESP 033001 (SK37)), auto 2013.
On a car in 2014 29 bytes (MK100ESP 063 ***) ref. the encoding is not risked different.

Encoding
(for cars with automatic transmission)

Block 03 → coded-long coded → Byte 25 → bit 0, bit 5 • enable (" 20 "will be replaced by" 21 ")
(for cars with manual transmission)

Block 03 → coded-long coded → Byte 25 → bit 0 → enable

Then (for cars with automatic transmission and manual transmission)

Block 03 → adaptation → MAS02138-Assistant for travel on the rise → select the desired value → save

1.9 Activating Indirect TPMS

Description
When Indirect TPMS (Indirect Tire Pressure Sensor) is running, the information is taken from the ABS unit. If the wheel is flat, then its radius decreases and the rotational speed
increases. If this change persists for a certain time, then the on-board computer issues a warning about the need to check.

Features of the
Only for cars with ESC system!

Encoding
Better not to copy. The number 02 is responsible for the CAP, it does not matter 29, 30 or more bytes. Correct
activation of the indirect tire pressure sensor.
Block 03 -> long coding ->
• byte 27 → include bits 4 and 5 ( 1st option) or bits 4,5,6 ( 2nd option - for the pilot's park)
• byte 28 → turn on bit 7
• byte 29 → write the value 02 ( or 06, 07, 08, 09) - will differ in the ESC menus, we could have already done this in section 1.5
Block 17 → long coding → byte 4 → turn on bit 0. ( Indirect Tire Pressure Monitoring System (TPMS) installed)
Block 5F → adaptation →
• (13) - Vehicle function list BAP-tire_pressure_system_0x07 → value "active"
• (14) - Vehicle function list BAB-tire_pressure_system_0x07_msg_bus → value "data bus chassis" (many
have it initially)
• (56) - Vehicle menu operation-menu_display_rdk → value "active"
• (58) - Vehicle menu operation-menu_display_rdk_over_threshold_high → value "active" (often initially)

We clean the 3rd block from errors.

Notes (edit)
The sensor menu should appear in the radio settings, where you can save / reset the tire pressure memory. Sometimes the pressure error can hang. To remove, turn off the
coding in the tidy, and then turn it on again.
one. Do not be afraid of error in the 3rd block after setting the bits, it will go away.
2. In order for the SET button to appear in the menu, either reload the radio tape recorder, or reset the "Tires" to the factory settings
3. The SET button does not appear immediately, after 5 minutes, or even more. It is better to turn off the ignition, open the door and close the water and wait
at least 10. The system is calibrated in six (!) Speed ranges: 10-40, 40-60, 60-80, 80-100, 100-120 and over 120 km / h. It works confidently in those ranges in which the calibration
process is completed by 60-100%. Naturally, with a turned steering wheel, active acceleration and braking, the calibration process is interrupted. Well, its performance and
functionality depends on the correct activation and configuration of the system.

1.10 BDW adaptation

Features of the
BDW (Brake Disc Wiper) - "drying discs", allows you to leave the brake discs dry and clean in rainy weather. The system is activated when the wipers are turned on (manually or
automatically) for more than 5 seconds
There are 3 values: weak, strong, default. worth (weak)
Encoding
Block 03 → adaptation → Disk drying → select the desired value → save

eight
1.11 Activating / Configuring XDS

Features of the
Activation of the XDS function allows you to brake the inner wheel for a better entry into the turn. It is done only by
Odis, although it seems that Vasya can
5Q0 907 379 - 03 block without letter at the end - WITHOUT ESP, only ABS - almost nothing can be configured in it 5Q0 907 379 - 03 block
with letter A at the end - with ESP, but no XDS
5Q0 907 379 - 03 block with the letter K, R at the end - with ESP, with full support for everything. There are three
meanings of how XDS works:
• minimum
• normal
• maximum

Encoding
Block 03 → Long coding → Byte 23 → check the boxes in bits 1 and 2 ( If the jackdaw was on bit 1, put also bit 2 and
vice versa)

Or Block 03 → Long coding → Byte 23, activate bits 1,2,6.

then setting
Block 03 → Login 20103, Adaptations → Expanded electronic differential lock → maximum → activate

Notes (edit)
For motors up to 110 kW byte 23 Enable bit 1 For motors with 135 and 155
kW byte 23 Enable bit 2 For motors above 162 kW byte 23 Enable bits 1 and
2 Both bytes have been activated.

1.12 Deactivation of the "Start-stop" system

Encoding
Block 19 → adaptation → [VN] _Start_stop_voltage_limit: → [LN] _start_stop_voltage_limit: 7.6 [UN] _V 12.0
or
Block 19 → adaptation → (1) start / stop Au.Temperaturvorgabe-Minimaltemperatur ( select the channel at the very bottom) → change
value to "50" ( the default is "-50")

1.13 Reconfiguring the accelerator pedal

Features of the
Possible options for values of 0 bytes: 0C or 01
- from the factory
09 - Skoda / Seat / Volkswagen
0A - Audi option 1 02
- Audi option 2

Encoding
Block 01 → closed area 16 → enter code 27971 → encoding 07 → byte 0 → Bit 0 → change to bit 1 ( was 01 (Skoda), now 02
(Audi)) -> coding -> long coding -> 0 Byte → write 0C.
Notes (edit)
After that, it is necessary to adapt the damper. But the most complete effect will be after the adaptation of DSG-7
PS there may be mistakes!

1.14 Elimination of "bluntness" of the gas pedal

Any unauthorized deviation from this manual does not guarantee further correct operation of the vehicle's electronics systems. We select the firmware from the
corresponding folder and flash the engine ECU.
!!!!!!!! In no case do we change the firmware letter - only the numbers are the version !!!!!!!!
If your revision number coincides with the latest update, you need to downgrade the version (upload an earlier firmware) and then flash the current update, otherwise the
firmware will not upload correctly. The firmware of the 01 block on the MQB is almost always not the first time. After each unsuccessful attempt, exit the firmware menu
and clear errors in block 01. And so until the firmware is filled in correctly. Next, open the ODIS service - Diagnostics. → We choose the new most powerful A3 221 kW. →
Uncheck the guided troubleshooting box. 01 block - slave functions - throttle adaptation.

This concludes our procedure.

nine
1.15 BAS adaptation

Features of the
BAS (Brake Assist System) The emergency braking system is an electronic pressure control system in the hydraulic brake system, which, in the event of emergency braking
and insufficient effort on the brake pedal, independently increases the pressure in the brake line.

Encoding
Block 03 (ABS) → adaptation → brake assist → Set (0-average, 1-low, 2-high) - press Test - after the message is displayed
that everything is OK, press Save - Done

10
2. LIGHT

2.1 Switching on the rear dimensions in the DRL mode

Encoding
Option with the inclusion of rear dimensions in the DRL mode with illuminated numbers and tidy

Block 09 → login-password 31347 → adaptation →

(6) -Tagfahrlicht-Dauerfahrlicht aktiviert zusaetzlich Standlicht auswählen → activate → save
Features of the
Unforgettable to disable the previous option if it was enabled
The option to turn on only the rear dimensions in the DRL mode - without backlighting the license plate and tidy

Block 09 → login-password 31347 → adaptation →

(9) -Leuchte23SL HLC10-Lichtfunktion D 23 → select → Daytime running lights → save → then → (9)
- Leuchte24SL HRA65-Lichtfunktion D 24 → select → Daytime running lights → save
Notes (edit)
In both cases, channel 10 is setting the brightness, which by default has a value of 65, I changed it to 85. Thus, I ensured that in the DRL mode, in addition to the front lights, the
outermost parts of the rear lights (vertical stripes) are also lit. I liked it more, but you can, of course, ignite the dimensions completely by activating two more channels per headlight.

2.2 Disabling DRL in the "0" mode when lifting the handbrake

Encoding
Block 09 → login-password 31347 → adaptation →
IDE06864-ENG122184-Daylight mode - Tagfahrlicht Dauerfahrlicht bei Handbremse abschalten
→ activate → save

2.3 DRL menu

Features of the
Does not depend on the position of the parking brake (p. 2.3)

Encoding
Block 09 → login-password 31347 → adaptation → (2) -Daytime running lights-Tagfahrlicht Aktivierung durch BAD
oder Bedienfolge moeglich → activate → save
Channel name via odys [LO] _Tagfahrlicht Aktivierung durch BAP oder Bedienfolge moeglich

2.4 Mode of operation of parking lights

Features of the
there is

Encoding
Block 09 → login-password 31347 → adaptation →
(4) -Driving light and parking light-Parklicht ueber LSS aktiviert → select the desired value → save

2.5 "Polite turn signal"

Description
Changing the number of blinking of the turn signal in overtaking or lane change mode
The values are from 1 to 5, I tried both 4 and 5, but in the "factory" settings - 3 times, they seem to be optimal

Encoding
Block 09 → login-password 31347 → adaptation →
(2) -Turn signal control → "3" set the required amount of "5" → save
Note
CAR → MENU → factory settings → reset to factory settings Can be done via
ODIS Service, Guided functions, 1 to 5

eleven
2.6 Setting the FLA Response Rate Threshold

Note
FLA - high beam assistant
Encoding
Block A5 → adaptation → Aktivierungsgeschwindigkeit f ür Fernlichtassistent (activation speed for high-beam
assistant) → set the speed (default 57) → save

2.7 LEDs in room lighting

Note
If from the factory you did not have LEDs in the backlight of the room, but you wanted to install them. So that after their installation an error does not pop up and this
adaptation is required.

Encoding
Block 09 → login-password 31347 → adaptation → (1) -Leuchte25KZL HA59-Lasttyp 25 → enter the value " 43 Allgemeine led " or " 6
LedLichtModul " ( relevant for station wagons) →
to keep ( was 18 - 2 * 5W)
(6) - Leuchte25KZL HA59-Dimmwert AB 25 → enter the brightness “100” (0-127) → save
on the elegance it is activated through the bolero

Block 09 → login-password 31347 → adaptation →

Channel 1 - YES, Channel 2 - YES, Channel 8 - Activ, Channel 7 - Activ, Channel 3 - Normal

2.8 LEDs in footlights

Encoding
Block 09 → code 31347 → Adaptation → Leuchte 30FR LC72 →
• 1channel - 43 Algemeine Led

• 6channel - 127 , or 100 so that the backlight can be controlled from the radio

2.9 CH activation

Note
CH - Coming Home function, at night you close the car with a button on the key, and the dipped beam is on for a while, illuminating the way to your house with dipped beam.
Below is a variant for the duration of illumination - 40 sec.
Encoding
Block 09 → login-password 31347 → adaptation →
(1) -Comfort illumination-Coming Home Verbaustatus → was avtomat ( light switch in "Auto") → choose → manual
(light switch in "Manual") → save
(2) -Comfort illumination-Menuesteuerung Coming Home Werkseinstellung → was not active → select → active →
to keep ( activation of the Coming Home menu in the head unit)
(3) -Comfort illumination-Menueeinsteliung Cominghome → was "0" enter "40" → save (4) -Comfort illumination-Coming
Home Leuchten → leave "low beam" (" Low beam "- illumination through the dipped beam headlights;" Fog light
"- lighting through the front PTF and low beam headlights)
(5) -Comfort illumination-Coming-home Einschaltereignis → leave "ignition" (" Driver door "- Coming Home is activated
after opening the door; "ignition" - the Coming Home function is activated after turning off the ignition and removing the key from the ignition lock);
(6) -Comfort illumination-Helligkeitsschwelle Infrarot-Messung → was "0" enter "1" or "2"? → save (7)
- Comfort illumination-Leaving-Home Verbausstatus, value "Enabled" (" Enabled "- activation in the head unit menu
Leaving Home)

(8) -Comfort illumination-Menuesteuerung Leaving-home Freischaltung per BAP, value "active" [LO]
_Menueeinstellung Leaving-home Zeit per BAP: 40 sec
Notes (edit)
Then, in the on-board computer. reset to factory settings. Before leaving the car, blink a high beam

12
2.10 CH / LHmenu

Note
CH - Coming Home function, at night you close the car with a button on the key, and the dipped beam is on for a while, illuminating the way to your house with dipped beam.

LH - Leaving Home function, at night you leave the house, open the car with a button on the key, and the car illuminates your way with low beam.

Encoding
Block 09 → login-password 31347 → adaptation →
(11) -driving light and parking licht → menueeinstellung CHO LHO → choose → Menuesteuerung Zeit aktiveren
→ save

2.11 CH / LH source setting

Note
CH - Coming Home function, at night you close the car with a button on the key, and the dipped beam is on for a while, illuminating the way to your house with dipped beam.

LH - Leaving Home function, at night you leave the house, open the car with a button on the key, and the car illuminates your way with low beam.

Encoding
CH / LH through front PTFs - option # 1
Block 09 → login-password 31347 → adaptation →
[VN] _Komfortbeleuchtung: [ LO] _Coming home Leuchten: [VN] _fog light ( was [VN] _Low Beam)
[VO] _Leuchte6ABL LC5: ( turning off the neighbor)
[LO] _Lichtfunktion B 6: [VO] _nicht aktiv ( was [VO] _Coming Home oder Leaving Home aktiv)
[VO] _Leuchte7ABL RB1: ( turning off the neighbor)
[LO] _Lichtfunktion B 7: [VO] _nicht aktiv ( was [VO] _Coming Home oder Leaving Home aktiv)
[VO] _Leuchte12NL LB45: ( we hook up the function on PTF, in principle, on any channel, so that the brightness and direction are maximize)
[LO] _Lichtfunktion C 12: [VO] _Coming Home oder Leaving Home aktiv ( was [VO] _nicht aktiv)
[VO] _Leuchte13NL RB5: ( we hook up the function on PTF, in principle, on any channel, so that the brightness and direction are maximize)
[LO] _Lichtfunktion C 13: [VO] _Coming Home oder Leaving Home aktiv ( was [VO] _nicht aktiv)
CH / LH through front PTFs - option # 2
• Leuchte12NL LB45-Lichtfunktion C 12 → Interior light
• Leuchte12NL LB45- Dimming CD 12 → 100
• Leuchte12NL LB45-Dimming Direction CD 12 → maximize
• Leuchte13NL RB5-Lichtfunktion C 13 → Interior light
• Leuchte13NL RB5- Dimming CD 13 → 100
• Leuchte13NL RB5-Dimming Direction CD 13 → maximize
CH / LH through daytime running lights

• Leuchte4TFL LB4-Lichtfunktion E 4 → Interior light

• Leuchte4TFL LB4- Dimming EF 4 → 100
• Leuchte4TFL LB4-Dimming Direction EF 4 → maximize
• Leuchte5 TFL RB32-Lichtfunktion E 5 → Interior light
• Leuchte5 TFL RB32- Dimming EF 5 → 100
• Leuchte5 TFL RB32-Dimming Direction EF 5 → maximize
CH / LH via reversing lights
• Leuchte28RFL LC11- LightFunction C 28 → Interior light
• Leuchte28RFL LC11- Dimming CD 28 → 100
• Leuchte28RFL LC11- Dimming Direction CD 28 → maximize
• Leuchte29RFL RA64- LightFunction C 29 → Interior light
• Leuchte29RFL RA64- Dimming CD 29 → 100
• Leuchte29RFL RA64- Dimming Direction CD 29 → maximize

2.12 Activating Corner

Note
The Corner function is a mode of operation of the front foglights, which allows you to increase the angle of illumination when turning (illuminate the space at an angle from -30 ° to
+ 60 °).

Encoding
Block 09 → login-password 31347 → adaptation →

13
Leuchte 12NL LB45-Lichtfunktion B 12 → Abbiegelicht links
Leuchte 13NL RB5-Lichtfunktion B 13 → Abbiegelicht rechts or

Block 09 → login-password 31347 → adaptation →

(9) -Leuchte 12 NL LB45-Lichtfunction D 12 -Abbiegelicht links; (10)
- Leuchte 12 NL LB45-Dimmwert CD 12 - 80 (brightness, incandescence) (11)
-Leuchte 12 NL LB45-Dimming Direction CD 12 —maximize; (nine)

- Leuchte 13 NL RB45-Lichtfunction D 13 -Abbiegelicht rechts; (10) -Leuchte 13 NL

RB45-Dimmwert CD 13 - 80 (brightness, incandescence); (eleven)

- Leuchte 13 NL RB45-Dimming Direction CD 13 —maximize; For A7FL

Leuchte12NL LB45-Lichtfunktion C12 -> Abbiegelicht links

Leuchte13NL RB5-Lichtfunktion C13 -> Abbiegelicht rechts
For some A7FLs, additional adaptation channels need to be additionally changed.
For ODIS
[VN] _Static_Cornering_Light_Adaptation
• [LO] _Abdimmgeschwindigkeit: 0.0 [UN] _% / s -> 127.5 [UN] _% / s [LO]
• _Maximaltemperatur: 0.0 [UN] _ ° C -> 100.0 [UN] _ ° C [LO] _obere
• Grenztemperatur: 0.0 [UN] _ ° C -> 95.0 [UN] _ ° C [LO] _untere Grenztemperatur:
• 0.0 [UN] _ ° C -> 80.0 [UN] _ ° C For VCDS

• IDE03638-ENG116677-static AFS light-Abdimmgeschwindigkeit, 127.5% / s

• IDE03638-ENG116682-static AFS light-Maximaltemperatur, 100.0 ∞C
• IDE03638-ENG116679-static AFS light-obere Grenztemperatur, 95.0 ∞C
• IDE03638-ENG116680-static AFS light-untere Grenztemperatur, 80.0 ∞C

2.13 On / Off Corner depending on speed

Note
The Corner function is a mode of operation of the front foglights, which allows you to increase the angle of illumination when turning (illuminate the space at an angle from -30 ° to
+ 60 °).
Encoding
Block 09 -> login-password 31347 -> adaptation -> (3) - ...
(Static AFS) → enter the value "0"
(4) -… (Static AFS) → enter the value "50" or "40"

2.14 Activation of the second rear PTF

Features of the
From the factory, only the rear left PTF works, this adaptation allows the operation of two rear PTFs, except for the Octavia A7 FL
Encoding
Block 09 → login-password 31347 → adaptation →
(4) -Leuchte26NSL LA72-Lichtfunktion A 26 → choose → Nebelschlusslicht wenn kein Anhaenger gesteckt und Rechtsverkehr
→ to keep → then →
(4) -Leuchte27NSL RC6-Lichtfunktion A 27 → choose → Nebelschlusslicht wenn kein Anhaenger gesteckt und
Rechtsverkehr → to keep
(6) -Leuchte27NSL RC6- Dimmwert AB 27 → the value "0" is changed to "100" → to keep ( Written for LED, but also stood and
for ordinary)
Left rear PTF only: [VO] _Nebelschlusslicht wenn kein Anhaenger gesteckt und Linksverkehr

fourteen
2.15 Stroboscope (DRL (halogen) + distant + turn signals)

Features of the
This coding is for cars with a complete set of "halogen" DRL lamps.
Encoding
Block 09 → login-password 31347 → adaptation →
(16) -Leuchte 4TFL LB4 Lichtfunktion G4 → select → Blinken Links Hellphase → save
(17) -Leuchte 4TFL LB4 Lichtfunktion H4 → select → Lichthupe generell → save the value
(18) -Leuchte 4TFL Lt4 G4 Dimmwer
(19) -Leuchte 4TFL LB4 Dimming Direction GH4 → select → minimize → save (16) -Leuchte
5TFL RB32 Lichtfunktion G5 → select → Blinken rechts Hellphase → save (17) -Leuchte 5TFL
RB32 Lichtfunktion H5 → save generic 18) - Leuchte 5TFL RB32 Dimmwert GH5 → value "0"
remains
(19) - Leuchte 5TFL RB32 Dimming Direction GH5 → select → minimize → save

2.16 Stroboscope (far + PTF)

Encoding
Block 09 → login-password 31347 → adaptation → driveng light and parking lightZahl der aktivern Sheinwerfer Auf 2
limitieren → activate → save
or
Block 09 → login-password 31347 → adaptation → driveng light and parking light - Zahl der aktiven Scheinwerfer auf 2
limitieren → activate → save
16 channel Leuchte 12NL LB45 lichtfunction G12 set-Lichthupe generell 19 channel
Leuchte 12NL Dimming direction GH12- was max set min 16 channel Leuchte 13NL
RB5 lichtfunction G13 set-Lichthupe generell 19 channel Leuchte 13NL Dimming
max direction set GH13- it

2.17 Strobe (far + DRL)

Features of the
Stroboscopes winking (far + PTF + DRL) or DRL (LED strip) + far (bi-xenon):

Encoding
Block 09 → login-password 31347
Leuchte2SL VLB10-Lichtfunktion G 2 - select "Lichthupe Generell"
Leuchte2SL VLB10-Dimming Direction GH 2 select "minimize" Leuchte3SL
VRB21-Lichtfunktion G 3 select "Lichthupe Generell"

2.18 Activation of PTF together with DRL

Encoding
Block 09 → login-password 31347 → adaptation →
Leuchte12NL LB45-Lichtfunktion С12 → choose → Tagfahrlicht (Daytime Running Light) save Leuchte12NL
LB45-Lichtfunktion D12 → not active
Leuchte12NL LB45-Dimmwert CD12 → value "100" → save Leuchte12NL
LB45-Dimming Direction CD12 → choose → maximize
Leuchte13NL RB5-Lichtfunktion С13 → choose → Tagfahrlicht (Daytime Running Light) → save Leuchte13NL
RB5-Lichtfunktion D13 → not active
Leuchte13NL RB5-Dimmwert CD13 → value "100" → to keep
Leuchte13NL RB5-Dimming Direction CD13 → choose → maximize → to keep

fifteen
2.19 Activation of DRL in conjunction with low beam

Features of the
Here we replace Coming Home / Leaving Home, which means that when seeing off and meeting with light, the DRL lamp will not light up. Here you can hang not on the C4 function,
but on another free function, for example, FGH
Encoding
Block 09 → login-password 31347 → adaptation →
(front left DRL)

(8) -Leuchte 4TFL LB44-Lichtfunktion C4 → Сoming Home oder Leaving Home Active → change to → Abblendlicht Links ( low beam on the
left)
(10) -Leuchte 4TFL LB44-Dimmwert CD4 → change the value "30" to "100" → to keep
(front right DRL)

(8) -Leuchte 5TFL RB32-Lichtfunktion C5 → Сoming Home oder Leaving Home Active → change to → Abblendlicht Rechts ( low beam on the
right) → to keep
(10) -Leuchte 5TFL RB32-Dimmwert CD5 → change the value "30" to "100" → to keep
Notes (edit)
Be careful! Remember the previous values.

2.20 Disabling the front dimensions when the dipped beam is on

Features of the
Since there is no separate lamp of dimensions in octavia a7, everything is done through the DRL
lamp. 100% DRL is a daytime running light. 30% of DRL are dimensions.
Encoding
Block 09 → login-password 31347 → adaptation →
(12) -Leuchte 4TFL LB44-Lichtfunktion G4 → choose → Abblendlicht links → to keep ( It was nicht active)
(13) -Leuchte 4TFL LB44-Lichtfunktion H4 → remains → not active (14) -Leuchte 4TFL LB44-Dimmerwert
GH4 → value "0" → save (15) -Leuchte 4TFL LB44-Dimming Direction GH4 → choose → minimize → to keep ( It
was maximize)

(12) -Leuchte 5TFL RB32-Lichtfunktion G5 → choose → Abblendlicht rechts → to keep ( It was nicht active)
(13) -Leuchte 5TFL RB32-Lichtfunktion H5 → remains → not active (14) -Leuchte 5TFL RB32-Dimmerwert
GH5 → value "0" → save (15) -Leuchte 5TFL RB32-Dimming Direction GH5 → choose → minimize → to keep ( It
was maximize)

2.21 Brightness of the front dimensions as DRL

Features of the
Since there is no separate lamp of dimensions in octavia a7, everything is done through the DRL lamp. 100% DRL is a daytime running light. 30% of DRL are dimensions.

We hang Abblendlicht links for 04 lamps, Abblendlicht rechts for 05 lamps and set the brightness to 100 on a free channel, Dimmerwert - maximize.

Encoding
Block 09 → login-password 31347 → adaptation →
(12) -Leuchte 4TFL LB4-Lichtfunktion G4 → choose → Abblendlicht links → to keep ( It was nicht active)
(14) -Leuchte 4TFL LB4-Dimmerwert GH4 → value "100" → save (15) -Leuchte 4TFL LB4-Dimming Direction GH4 → choose
→ maximize → save (12) -Leuchte 5TFL RB32-Lichtfunktion G5 → choose → Abblendlicht rechts → to keep ( It was nicht active)

(14) -Leuchte 5TFL RB32-Dimmerwert GH5 → value "100" → save (15) -Leuchte 5TFL RB32-Dimming
Direction GH5 → choose → maximize → to keep

2.22 Activating the inclusion of the rear PTF together with the brakes

Encoding
Block 09 → login-password 31347 → adaptation →
(8) -Leuchte 26NSL LA72-Lichfunktion C26 → Standlicht Algemein (Schlusslicht, Positionslicht, Begrenzungslicht) → change to → Break
Light → to keep
(10) -Leuchte 26NSL LA72-Dimmerwert CD26 → the value "16" is replaced by "100" → to keep

sixteen
(8) -Leuchte 27NSL RC6-Lichfunktion C27 → Standlicht Algemein (Schlusslicht, Positionslicht, Begrenzungslicht) → change to → Break
Light → to keep
(10) -Leuchte 27NSL RC6-Dimmerwert CD27 → the value "16" is replaced by "100" → to keep
---

(8) Leuchte 26NSL LA72-Lichfunktion C26 -Standlicht Algemein (Schlusslicht, Positionslicht, Begrenzungslicht): WE LEAVE
(10) Leuchte 26NSL LA72-Dimmerwert CD26 - value "16": WE LEAVE
(8) Leuchte 27NSL RC6-Lichfunktion C27 - Standlicht Algemein (Schlusslicht, Positionslicht, Begrenzungslicht): WE LEAVE
(10) Leuchte 27NSL RC6-Dimmerwert CD27 → value "16": WE LEAVE
Leuchte 26NSL LA72-Lichfunktion В26 - put Break Light ( was not active)
Leuchte 27NSL RC6-Lichfunktion В27 - put Break Light ( was not active)
Leuchte 27NSL RC6-dimmwert AB27 - put 100 ( I had 100)

2.23 Turning on the front turn signals (American var) together with the dimensions

Encoding
Block 09 → login-password 31347 → adaptation →

(9) -Leuchte 0BLK VL B36 Lichtfunktion D0 → Not Active → change to → Standlicht allgemein (Schlusslicht, Positionslicht,
Begrenzungslicht) → to keep
(10) -Leuchte 0BLK VLB36 Dimmwert CD0 → the value "0" is changed to "30" → save (12) -Leuchte 0BLK VLB36 Lichtfunktion
E0 → Not Active → change to → Blinken Links Dunkelphase → save (15) - Leuchte 0BLK VLB36 Dimming Direction EF0 →
maximize → change to → minimize → to keep

(9) -Leuchte 1BLK VRB20 Lichtfunktion D0 → Not Active → change to → Standlicht allgemein (Schlusslicht, Positionslicht,
Begrenzungslicht) → to keep
(10) -Leuchte 1BLK VRB20 Dimmwert CD0 → the value "0" is changed to "30" → save (12) -Leuchte 1BLK VRB20 Lichtfunktion E0 →
Not Active → change to → Blinken Rechts Dunkelphase → save (15) - Leuchte 1BLK VRB20 Dimming Direction EF0 → maximize → change
to → minimize → to keep

2.24 Inclusion of front turn signals (American var) instead of dimensions

Encoding
Block 09 → login-password 31347 → adaptation →

(nine)- Leuchte 0BLK VL B36 Lichtfunktion D0 → Not Active → change to → Standlicht allgemein (Schlusslicht, Positionslicht,
Begrenzungslicht) → to keep
(10) -Leuchte 0BLK VLB36 Dimmwert CD0 → the value "0" is changed to "30" → to keep
(12) -Leuchte 0BLK VLB36 Lichtfunktion E0 → Not Active → change to → Blinken Links Dunkelphase → save (15) - Leuchte 0BLK VLB36
Dimming Direction EF0 → maximize → change to → minimize → save (9) - Leuchte 4TFL LB4 36 Lichtfunktion A4 → Standlicht allgemein
(Schlusslicht, Positionslicht, Begrenzungslicht) → change to → Not Active → to keep

(nine)- Leuchte 1BLK VRB20 Lichtfunktion D1 → Not Active → change to → Standlicht allgemein (Schlusslicht, Positionslicht,
Begrenzungslicht) → to keep
(10) -Leuchte 1BLK VRB20 Dimmwert CD1 → the value "0" is changed to "30" → save (12) -Leuchte 1BLK VRB20 Lichtfunktion E1 → Not Active → cha
to → Blinken Rechts Dunkelphase → save (15) - Leuchte 1BLK VRB20 Dimming Direction EF1 → maximize → change to → minimize → save (9) - Leuc
5TFL RB32 Lichtfunktion A5 → Standlicht allgemein (Schlusslicht, Positionslicht, Begrenzungslicht) → change to → Not Active → to keep

17
2.25 Winking reversing lamps with turn signals when turning on the reverse
speed and emergency gang

Encoding
Block 09 → login-password 31347 → adaptation →

(8) -Leuchte 28RFL LC11 Lichtfunktion C → Active → change to → Blinken Links Hellphase → save (9) -Leuchte 28RFL
LC11 Lichtfunktion D → remains → Not Active
(10) -Leuchte 28RFL LC11 Dimmwert CD → remains "0" → save (11) -Leuchte 28RFL LC11 Dimming Direction CD →
maximize → change to → minimize → to keep

(8) -Leuchte 29RFL RA64 Lichtfunktion C → Active → change to → Blinken Rechts Hellphase → save (9) -Leuchte 29RFL
RA64 Lichtfunktion D → remains → Not Active
(10) -Leuchte 29RFL RA64 Dimmwert CD → remains "0" →
(11) -Leuchte 29RFL RA64 Dimming Direction CD → maximize → change to → minimize →

2.26 Activation of the front PTFs when engaging reverse gear

Block 09 -> 16 Closed Area -> Code 31347 - Execute -> 10 - Adaptation -> (1) -static AFS light-bei Rueckwaertsfahrt
-> double sided

2.27 Increasing the brightness of the reversing lamps

Features of the
by about 25% (only with LED lamps installed).

Encoding
Block 09 -> 16 Closed Area -> Code 31347 - Execute -> 10 - Adaptation -> (6) Leuchte28RFL
LC11-Dimmwert AB 28 ( left side) is set to 100%, put 125% (6) -Leuchte29RFL RA64-Dimmwert AB 29 ( right
side) is set to 100%, set 125%

2.28 Increasing the brightness of the headlamps

Features of the
Increase the brightness of the low and high beam lamps. For halogen headlights only !!!

Encoding
Block 09 → Closed area - enter login 31347 → Adaptation - Channels: Middle

• Leuchte6ABL LB44-Dimming_AB_6 set to 100%, put 125% Leuchte7ABL

•
RB5-Dimming_AB_7 set to 100%, set 125% Far

• Leuchte9FL RB7-Dimming_AB_9 set to 100%, put 125% Leuchte8FL

• LB42-Dimming_AB_8 set to 100%, set 125%
Notes (edit)
It should be understood that these operations will result in reduced lamp life.

2.29 Increasing the brightness of PTF lamps

Features of the
by about 25% (only with LED lamps installed).

Encoding
Block 09 → 16 Closed area → Code 31347 - Execute → 10 - Adaptation → (6) Leuchte12NL
LB45-Dimmwert AB 12 ( left tumanka) is set to 100%, put 125% (6) Leuchte13NL RB5-Dimmwert AB 12 (
right tumanka) is set to 100%, set 125%

eighteen
2.30 Emergency braking alarm

Coding:
09 - adaptations → Auxiliary light function ( Assistance light functions) - Notbremsanzeige NBA → active

Note:
choose only one of these two.

2.31 LED rear lights

[VO] _Leuchte20BR LA71:

[LO] _Lasttyp 20: [VO] _34 - LED Bremsleuchten
[LO] _Lampendefektbitposition 20: nine
[LO] _Fehlerort mittleres Byte DTC-DFCC 20: 39
[LO] _Lichtfunktion A 20: [VO] _Bremslicht
[LO] _Lichtfunktion B 20: [VO] _nicht aktiv
[LO] _Dimmwert AB 20: 100 [LO]
_Lichtansteuerung HD AB 20: [LO] [VO] _always
_Lichtfunktion C 20: [VO] _nicht aktiv
[VO] _Standlicht allgemein (Schlusslicht, Positionslicht, Begrenzungslicht)
[LO] _Lichtfunktion D 20: [VO] _nicht aktiv
[VO] _Parklicht links (beidseitiges Parklicht aktiviert li & re)
[LO] _Dimmwert CD 20: 0
eighteen

[LO] _Dimming Direction CD 20: [VO] _maximize

[LO] _Lichtfunktion E 20: [VO] _Coming Home oder Leaving Home aktiv
[LO] _Lichtfunktion F 20: [VO] _nicht aktiv
[LO] _Dimmwert EF 20: 0
eighteen

[LO] _Dimming Direction EF 20: [VO] _maximize

[LO] _Lichtfunktion G 20: [VO] _nicht aktiv
[LO] _Lichtfunktion H 20: [VO] _nicht aktiv
[LO] _Dimmwert GH 20: 0
[LO] _Dimming Direction GH 20: [VO] _maximize

[VO] _Leuchte21BR RC8:

[LO] _Lasttyp 21: [VO] _34 - LED Bremsleuchten
[LO] _Lampendefektbitposition 21: nineteen

[LO] _Fehlerort mittleres Byte DTC-DFCC 21: 3A

[LO] _Lichtfunktion A 21: [VO] _Bremslicht
[LO] _Lichtfunktion B 21: [VO] _nicht aktiv
[LO] _Dimmwert AB 21: 100 [LO]
_Lichtansteuerung HD AB 21: [LO] [VO] _always
_Lichtfunktion C 21: [VO] _nicht aktiv
[VO] _Standlicht allgemein (Schlusslicht, Positionslicht, Begrenzungslicht)
[LO] _Lichtfunktion D 21: [VO] _nicht aktiv
[VO] _Parklicht rechts
[LO] _Dimmwert CD 21: 0
eighteen

[LO] _Dimming Direction CD 21: [VO] _maximize

[LO] _Lichtfunktion E 21: [VO] _Coming Home oder Leaving Home aktiv
[LO] _Lichtfunktion F 21: [VO] _nicht aktiv
[LO] _Dimmwert EF 21: 0
eighteen

nineteen
[LO] _Dimming Direction EF 21: [VO] _maximize
[LO] _Lichtfunktion G 21: [VO] _nicht aktiv
[LO] _Lichtfunktion H 21: [VO] _nicht aktiv
[LO] _Dimmwert GH 21: 0
[LO] _Dimming Direction GH [VO] _maximize
21: ________________________
[VO] _Leuchte23SL HLC10:
[LO] _Lasttyp 23: [VO] _32 - allgemeine LED bis 12W
[VO] _18 - 2 * 5W
[LO] _Lampendefektbitposition 23: A
[LO] _Fehlerort mittleres Byte DTC-DFCC 23: 29
[LO] _Lichtfunktion A 23: [VO] _Standlicht allgemein (Schlusslicht, Positionslicht, Begrenzungslicht)
[LO] _Lichtfunktion B 23: [VO] _Parklicht links (beidseitiges Parklicht aktiviert li & re)
[LO] _Dimmwert AB 23: 100
65
[LO] _Lichtansteuerung HD AB 23: [VO] _always
[LO] _Lichtfunktion C 23: [VO] _Coming Home oder Leaving Home aktiv
[LO] _Lichtfunktion D 23: [VO] _nicht aktiv
[LO] _Dimmwert CD 23: 100
65
[LO] _Dimming Direction CD 23: [VO] _maximize
[LO] _Lichtfunktion E 23: [VO] _nicht aktiv
[LO] _Lichtfunktion F 23: [VO] _nicht aktiv
[LO] _Dimmwert EF 23: 0
[LO] _Dimming Direction EF 23: [VO] _maximize
[LO] _Lichtfunktion G 23: [VO] _nicht aktiv
[LO] _Lichtfunktion H 23: [VO] _nicht aktiv
[LO] _Dimmwert GH 23: 0
[LO] _Dimming Direction GH 23: [VO] _maximize

[VO] _Leuchte24SL HRA65:

[LO] _Lasttyp 24: [VO] _32 - allgemeine LED bis 12W
[VO] _18 - 2 * 5W
[LO] _Lampendefektbitposition 24: 1A
[LO] _Fehlerort mittleres Byte DTC-DFCC 24: 2A
[LO] _Lichtfunktion A 24: [VO] _Standlicht allgemein (Schlusslicht, Positionslicht, Begrenzungslicht)
[LO] _Lichtfunktion B 24: [VO] _Parklicht rechts
[LO] _Dimmwert AB 24: 100
65
[LO] _Lichtansteuerung HD AB 24: [VO] _always
[LO] _Lichtfunktion C 24: [VO] _Coming Home oder Leaving Home aktiv
[LO] _Lichtfunktion D 24: [VO] _nicht aktiv
[LO] _Dimmwert CD 24: 100
65
[LO] _Dimming Direction CD 24: [VO] _maximize
[LO] _Lichtfunktion E 24: [VO] _nicht aktiv
[LO] _Lichtfunktion F 24: [VO] _nicht aktiv
[LO] _Dimmwert EF 24: 0
[LO] _Dimming Direction EF 24: [VO] _maximize
[LO] _Lichtfunktion G 24: [VO] _nicht aktiv
[LO] _Lichtfunktion H 24: [VO] _nicht aktiv
[LO] _Dimmwert GH 24: 0
[LO] _Dimming Direction GH 24: [VO] _maximize
======================

twenty
[VO] _Leuchte26NSL LA72:
[LO] _Lasttyp 26: [VO] _9 - allgemeine Glühlampe 27W, auch H15
[LO] _Lampendefektbitposition 26: C
[LO] _Fehlerort mittleres Byte DTC-DFCC 26: 2E
[LO] _Lichtfunktion A 26: [VO] _Nebelschlusslicht wenn kein Anhaenger gesteckt und Rechtsverkehr
[LO] _Lichtfunktion B 26: [VO] _nicht aktiv
[LO] _Dimmwert AB 26: 100 [LO]
_Lichtansteuerung HD AB 26: [LO] [VO] _always
_Lichtfunktion C 26: [VO] _nicht aktiv
[VO] _Standlicht allgemein (Schlusslicht, Positionslicht, Begrenzungslicht)
[LO] _Lichtfunktion D 26: [VO] _nicht aktiv
[VO] _Parklicht links (beidseitiges Parklicht aktiviert li & re)
[LO] _Dimmwert CD 26: 0
sixteen

[LO] _Dimming Direction CD 26: [VO] _maximize

[LO] _Lichtfunktion E 26: [VO] _nicht aktiv
[LO] _Lichtfunktion F 26: [VO] _nicht aktiv
[LO] _Dimmwert EF 26: 0
sixteen

[LO] _Dimming Direction EF 26: [VO] _maximize

[LO] _Lichtfunktion G 26: [VO] _nicht aktiv
[LO] _Lichtfunktion H 26: [VO] _nicht aktiv
[LO] _Dimmwert GH 26: 0
[LO] _Dimming Direction GH 26: [VO] _maximize

[VO] _Leuchte27NSL RC6:

[LO] _Lasttyp 27: [VO] _9 - allgemeine Glühlampe 27W, auch H15
[LO] _Lampendefektbitposition 27: 1C
[LO] _Fehlerort mittleres Byte DTC-DFCC 27: 2F
[LO] _Lichtfunktion A 27: [VO] _Nebelschlusslicht wenn kein Anhaenger gesteckt und Linksverkehr
[LO] _Lichtfunktion B 27: [VO] _nicht aktiv
[LO] _Dimmwert AB 27: 100 [LO]
_Lichtansteuerung HD AB 27: [LO] [VO] _always
_Lichtfunktion C 27: [VO] _nicht aktiv
[VO] _Standlicht allgemein (Schlusslicht, Positionslicht, Begrenzungslicht)
[LO] _Lichtfunktion D 27: [VO] _nicht aktiv
[VO] _Parklicht rechts
[LO] _Dimmwert CD 27: 0
sixteen

[LO] _Dimming Direction CD 27: [VO] _maximize

[LO] _Lichtfunktion E 27: [VO] _nicht aktiv
[LO] _Lichtfunktion F 27: [VO] _nicht aktiv
[LO] _Dimmwert EF 27: 0
sixteen

[LO] _Dimming Direction EF 27: [VO] _maximize

[LO] _Lichtfunktion G 27: [VO] _nicht aktiv
[LO] _Lichtfunktion H 27: [VO] _nicht aktiv
[LO] _Dimmwert GH 27: 0
[LO] _Dimming Direction GH 27: [VO] _maximize

21
2.32 Dimming / winking / simultaneous operation of LED DRL when turning
indicators (Audi Style)

Features of the
except Octavia A7 FL

Encoding
Block 09 →. login-password 31347 → adaptation →

Dying out
(16) -Leuchte2SL VLB10-Lichtfunktion G 2 = Blinken links aktiv (beide Phasen) (18)
-Leuchte2SL VLB10-Dimmwert GH 2 = 0-35
(19) -Leuchte2SL VLB10-Dimming Direction GH 2 = minimize
(16) -Leuchte3SL VRB21-Lichtfunktion G 3 = Blinken rechts aktiv (beide Phasen) (18)
-Leuchte3SL VRB21-Dimmwert GH 3 = 0-35
(19) -Leuchte3SL VRB21-Dimming Direction GH 3 = minimize
Dimmwert channel, change from 35 to 25

Wink
(16) -Leuchte2SL VLB10-Lichtfunktion G 2 → choose → Blinken links aktiv (Hellphase) → save (18) -Leuchte2SL
VLB10-Dimmwert GH 2 → enter the value "0" → save (19) -Leuchte2SL VLB10-Dimming Direction GH 2 → choose
→ minimize → save (16) -Leuchte3SL VRB21-Lichtfunktion G 3 → choose → Blinken rechts aktiv (Hellphase) → save
(18) -Leuchte3SL VRB21-Dimmwert GH 3 → enter the value "0" → to keep

(19) -Leuchte3SL VRB21-Dimming Direction GH 3 → choose → minimize → to keep

Blinking along with the turn signal

(16) -Leuchte2SL VLB10 - Lichtfunktion G 2 - Blinken links Dunkelphase (18)
-Leuchte2SL VLB10 - Dimmwert GH 2 - 0
(19) -Leuchte2SL VLB10 - Dimming Direction GH 2 - minimize (16) -Leuchte3SL VRB21
- Lichtfunktion G 3 - Blinken rechts Dunkelphase (18) -Leuchte3SL VRB21
- Dimmwert GH 3 - 0
(19) -Leuchte3SL VRB21 - Dimming Direction GH 3 - minimize

2.33 Disabling interior lampshades when opening the trunk

Encoding
Block 09 →. login-password 31347 → adaptation →
[VN] _Interior Light Adaptation:
[LO] _Innenlicht bei offenem Heckdeckel einschalten: [VN] not_active ( was - active)

2.34 Turning off the license plate light when opening the trunk

Encoding
Block 09 → Closed area - enter login 31347 → Adaptation - channel: Leuchte 25KZL
HA60-Light_Control_HD_AB_25 → instead of "Always" select the value "Only if closed" → to keep

2.35 Setting the brightness of the tidy lighting in any light

Encoding
Block 17 → adaptation B
adaptation 17 block
For day mode: [ VO] _dimming_characteristic_curve_adjustment_clock_dia l_day
For night mode: [ VO] _dimming_characteristic_curve_adjustment_clock_dia l_night
They have parameters. All X is a Dutch value → ika, all that is Y brightness. Accordingly, X1 corresponds to
Y1. Next, change all Ys as in Y6, or to your liking

22
 DEFAULT SETTINGS

[VO] _dimming_characteristic_curve_adju [VO] _dimming_characteristic_curve_adju

stment_clock_dial_day stment_clock_dial_night
[LO] _X1: 0 [LO] _X1: 0
[LO] _Y1: 0 [LO] _Y1: 3
[LO] _X2: 32 [LO] _X2: A
[LO] _Y2: 0 [LO] _Y2: 3
[LO] _X3: 66 [LO] _X3: 46
[LO] _Y3: 0 [LO] _Y3: eleven
[LO] _X4: 96 [LO] _X4: 64
[LO] _Y4: A [LO] _Y4: 1F
[LO] _X5: DC [LO] _X5: DC
[LO] _Y5: 32 [LO] _Y5: 5A
[LO] _X6: FD [LO] _X6: FD
[LO] _Y6: 64 [LO] _Y6: 64
And so we went, in order to code the desired effect we need: Decoding of
lamps in adaptation, here it is:
- Leuchte0BLK VLB36 - Left front Leuchte1BLK VRB20 - Right
- front Leuchte2SL VLB10 - Left front Leuchte3SL VRB21 -
- Right front Leuchte4TFL LB4 - Left front DRL Leuchte5TFL
- RBL32 - Right front DRL Leuchte5TFL RBL32 - Right front
-
-
-
- Leuchte7ABL RB1 - Right near Leuchte8FL
- LB39 - Left far Leuchte9FL RB2 - Right far
-
- Leuchte10 SHUTTER LB23 - not used Leuchte11
- SHUTTER RB22 - not used Leuchte12NL LB45 - Left
- front PTF Leuchte13NL RB5 - Right front PTF
-
- Leuchte16BLK SLB35BLK SL KC9 - left side marker (xen.light) Leuchte17TFL R BLK
- SRB3TFL R BLK SR KC3 - right marker (xen. Headlight) Leuchte18BLK HLA60 - Rear left
- turn
- Leuchte19BLK HRC31 - Rear Right Turn Leuchte20BR LA71
- - Brake Left
- Leuchte21BR RC8 - Brake Right
- Leuchte23SL HLC10 - Left rear dimensions Leuchte24SL
- HRA65 - Right rear dimensions Leuchte25KZL HA59 -
- Number illumination Leuchte26NSL LA72 - Left rear PTF
- Leuchte27NSL RC6 - Right rear PTF
-
- Leuchte28RFL LC11 - Left rear headlight (when driving backward)
- Leuchte29RFL RA64 - Right rear headlight (when driving backward)
- Leuchte30FR LC72 - Lighting for feet
- Leuchte31AMBL 1C61 - Ambient light front left Leuchte32 AMBL 2C35 - Ambient
- light front right Leuchte33 AMBL 3C36 - Ambient light rear left Leuchte34 AMBL
- 4C37 - Ambient light rear right
-

BCM 5Q0 937 084 AB (Asset)

the following pins are missing:
block A - 1 2 5 8 10 11 15 18-28 33-42 67 70 (total 73) block B - 5 6 17 18
22 23 29 33 34 37 38 40-46 (total 46)
block C - 2 4 7 17 18 20 26 27 29 30 33 35-41 43 44 49 53-57 61 64 65 68-71 (total 73)
The following channels are available in the Active: B35, B3 - powered by the front PTF (1.2Active) C72 - powered
by the illumination of the legs (1.2Active)
The backlighting of the rear number can be paralleled with the side left or right tailgate, then pin A59 will be released (in case the desired channel suddenly burns out)

BCM 5Q0 937 084 AD (Ambishen)

the following pins are missing:
Block A: 8, 10, 11, 18-28, 38-42, 67, 70 (total 73)
Block B: 6, 17, 18, 22, 23, 29, 33, 34, 37, 38, 40-46 (total 46)
Block C: 2, 4, 7, 17, 18, 26, 29, 30, 33, 35-37, 38, 39, 41, 44, 49, 53-55, 61, 64-66, 68-71 (total 73) The following channels
are available in Ambishen: B10, B21, B35, B3 - free
The backlighting of the rear number can be paralleled with the side left or right tailgate, then pin A59 will be released

Next, you need a translation of actions that can be hung on a particular lamp:
- Blinken links Hellphase - works when the left turn signal lights up Blinken links
- Dunkelphase - works when the left turn signal goes out
- Blinken rechts Hellphase - works when the right turn signal lights up

23
 - Blinken rechts Dunkelphase - works when the right turn signal fades out
- Blinken links aktiv (beide Phase) - works constantly when the left turn signal is working Blinken rechts aktiv (beide Phase) - constantly when the right turn signal is
working
- Standlicht allgemein (Schlusslicht, Positionslicht, Begrenzungslicht) - Lights up in Parklicht links mode (beidseitiges Parklicht
- aktiviert li & re) - Lights up in Park mode. fire lion (hold off) Parklicht rechts
- - lit in park mode. fire right (switch off)
- Abblendlichts links - used with close left fire Abblendlicht rechts - used with
- close right fire Fernlicht links - lit with far left fire
-
- Fernlicht rechts - lights up with far right fire Lichthupe generell - turns on
- when the distant one blinks Nebellicht links - lights up when the left PTF is
- turned on Nebellicht rechts - lights up when the right PTF is turned on
- Tagfahrlicht - lights up when DRL
-
- Bremslicht - lit when the brake is pressed
- Rueckfahrlicht - lit when reversing
- Nebelschlusslicht - lights up when the rear PTF is switched on Heckdeckel offen - lights up
- when the trunk is opened Heckdeckel geschlossen - lights up when the trunk is closed
- Dimmung klemme 58xs - the brightness is regulated by the regulator from the passenger
- compartment
- Innenlicht - (in theory, it should depend on indoor lighting) but smoothly on. When open. doors Kofferraumlicht - lights up
- when you turn on the light in the trunk (when open)
Now, what to actually do with it:
We are looking for the lamp we need, its type will be indicated in the first channel. [LO]
_Lasttyp 5 Then comes the so-called function for this lamp A [LO] _Lichtfunktion A
The next item is the brightness as a percentage for this function for two channels [LO] _Dimmwert AB
Then the point that determines the direction of the change in brightness, ie attenuation or vice versa, is designated as min or max [LO] _Lichtansteuerung HD Then again the
function, but already B
And again the brightness

And again the direction

and so on down the list. Of course, some of the functions will already be taken, so we are looking for a free one and select the desired action, then in the next paragraph we set the
brightness for this function, the direction of the brightness change.
Probably not everyone understands. I also did not immediately understand this whole sequence of functions and brightness correctly, but now I will give an example and you will immediately understand
everything.
Let's take a closer look at a couple of examples.

Example one: Dimming when turning on the turn signal: (Audi Style):
09 - Onboard supply control unit → 16- Closed area → Enter the code - 31347 → Execute → 10- Adaptation select the channel:
- Leuchte2SL VLB10 light function G 2 we select the value active flashing left (both phases), i.e. here we set for the left dimension in the function G2 the action
when the left turn signal is working - active flashing left in both phases -both phases, because the turn signal when turned on , we have two working states lit
unlit.
- Leuchte2SL VLB10-dimming GH 2 set the value 35 - here we set the brightness for the G2 function
- Leuchte2SL VLB10 dimming Direction GH 2 select the value "minimize" and here we set the direction of the brightness change in our case to decrease.

Thus, if you translate these actions into understandable language, then it will sound like this - for the Leuchte2SL VLB10 lamp in the free function G2, set the following -
when the left turn signal is working, reduce the brightness to 35 percent.
We set the same actions for the right side:
- Leuchte3SL VRB21 light function G 3 set the value "Flashing right active (both phases)" Leuchte3SL
- VRB21-dimming GH 3 set the value 35
- Leuchte3SL VRB21 dimming Direction GH 3 select the value "minimize"

Example two: Blinking the turn signal and size:

09 - Onboard supply control unit → 16- Closed area → Enter the code - 31347 → Execute → 10- Adaptation select the channel:
- Leuchte2SL VLB10-Lichtfunktion G 2 as we can see in our list is the left-hand size lamp. In the free function G2, select the action Blinken links aktiv (Hellphase) for it,
which means, based on the table, that the gauge will work when the left turn signal lights up, just when it lights up.

- Leuchte2SL VLB10-Dimmwert GH 2 set the value to "0" while the brightness of the left side should be zero percent. Leuchte2SL VLB10-Dimming Direction GH 2 select the
- value "minimize", that is, it should decrease to zero.
That is, in translation it sounds like when the turn signal lights up, the envelope should go out to a brightness of 0 percent, respectively, when the turn signal goes out, it will
light up again.
For the right dimension Leuchte3SL VRB21-Lichtfunktion G 3 all the same, only the action for the function is selected for the right turn Blinken rechts aktiv (Hellphase).

Well, and another example, as Vladimir.fin explained to me, as if:

"In function adaptation (ABCDEFGH) there are a lot of meanings, you need to translate what you need and choose. And behind the functions there is brightness, goes to 2
channels. For example, I made a PTF for myself as a DRL. I went into the left fog, there A as tumanka, B as a corner I don't remember how to see off, D. I went to the free
channel E and marked it as DRL and set 80% in the brightness of EF. It also works with the right one. I also brought the gabatires to a constant with low beam. "

24
3. COMFORT.

3.1 Disabling the seat belt warning

Encoding
Block 17 → coding-long coding → 00 Byte → 2 bit and 4 bit → turn off

3.2 Disabling the notification of the ignition on when the door is opened

Features of the
There are 3 meanings:
- No display (tbd),
- Driver door,
- All doors.

Encoding
Block 17 → login-password 20103 → adaptation → Ignition active message; trigger → select "No display (tbd)" → to keep

or
Block 17 → login-password 20103 → adaptation → [VN] _Ignition_Active_Message → [LN] _Ignition_Active_Message → [VN]
_trigger_on_dc_door

3.3 Activation of the warning about the left ignition key

Encoding
17 block -> Adaptations ->
Channel "Ignition key left warning" activate
Features of the
Can't find channel

3.4 Saving the last heated seat level

Description
In general, a useful thing for cars with auto start, otherwise I cannot imagine the feasibility of this function.

Encoding
Block 08 → adaptation →
• Speicherung der Sitzheizungsstufe Fahrer (Retention of driver's seat heater level) → activate → save Speicherung der
• Sitzheizungsstufe Beifahrer (Retention of passenger's seat heater level) → activate → to keep

3.5 Adapting seat heating

Description
Temperature values in ° C in effluent: 32-33 / 36.50-37.50 / 40-41
Recommended for Okatavia A7: 24-25 / 32-33 / 40-41
Encoding
Block 09 → login-password 31347 → adaptation →
(1) -Driver seat heater… -Sitzheizung Stufe 1 untere Schaltschw → was "32" enter the desired value. → save (2) -Driver seat heater…
-Sitzheizung Stufe 1 obere Schaltschw → was "33" enter the desired value. → save (3) -Driver seat heater… -Sitzheizung Stufe 2
untere Schaltschw → was "32" enter the desired value. → save (4) -Driver seat heater ...
- Sitzheizung Stufe 2 obere Schaltschw → was "33" enter the desired value. → save (5) -Driver seat heater ...
- Sitzheizung Stufe 3 untere Schaltschw → was "36.5" enter the desired value. → save (6) -Driver seat heater ...
- Sitzheizung Stufe 3 obere Schaltschw → was "37.5" enter the desired value. → save (7) -Driver seat heater ...
- Sitzheizung Stufe 4 untere Schaltschw → was "36.5" enter the desired value. → save (8) -Driver seat heater ...
- Sitzheizung Stufe 4 obere Schaltschw → was "37.5" enter the desired value. → to keep

25
(9) -Driver seat heater… -Sitzheizung Stufe 5 untere Schaltschw → was "40" enter the desired value. → save (10) -Driver
seat heater… -Sitzheizung Stufe 5 obere Schaltschw → was "41" enter the desired value. → save (11) -Driver seat heater…
-Sitzheizung Stufe 6 untere Schaltschw → was "40" enter the desired value. → save (12) -Driver seat heater… -Sitzheizung
Stufe 6 obere Schaltschw → was "41" enter the desired value. → to keep
Notes (edit)
According to the observations of members of the forum, the Sitzheizung Stufe 2,4,6 values do not affect the heating, but it is also possible that these values affect the passenger seats.

3.6 Activating Easy Entry

Feature
Easy Entry - comfortable fit for electrically adjustable seats. When you turn off the ignition and open the door, the seat moves back. When the ignition is turned on, the seat returns to its original
position.

Encoding
Activating the function itself

36 block → Long coding → Byte 3 → bit 1 → activate

The ability to disable via the menu:
36 block → Long coding →
• Byte 3 → bit 1 → enable (Easy_Entry_front) Byte 9 → bit 6 →
•enable (Easy_Entry_over_MMI) 5F block → Adaptations →

• Car_Function_Adaptations_Gen2-menu_display_seat_configuration → Asset
• Car_Function_Adaptations_Gen2-menu_display_seat_configuration_over_threshold_high → Asset
• Car_Function_List_BAP_Gen2-driver_seat_0x10 → Assets
• Car_Function_List_BAP_Gen2-driver_seat_0x10_msg_bus → Comfort tire
If the passenger seat is also electrically adjustable, then this function can also be activated for it.
36 block → Long coding → Byte 6 bit 4 (easyentry_enable_passenger_over_driver_MMI)
We repeat the same and encode in block 6 (all 3 bits). (who does not have a passenger electric, probably byte 6 bit 4 on it does not need to be activated, but judging by the
scans that come across, it is also activated)
5F block → Adaptations →
• Car_Function_List_BAP_Gen2-Passenger_Seat_0x10 → Assets
• Car_Function_List_BAP_Gen2-Passenger_Seat_0x10_msg_bus → Comfort tire
Note
After encodings / adaptations, restart the radio

3.7 Activating AUTO steering wheel heating

Feature
only for Octavia A7 FL

Encoding
Block 08 → coding-long coding → Byte 13 → bit 2 → activate.

3.8 Display of climate fan speed in AUTO

Encoding
Block 08 → coding-long coding → 11 Byte → 6 bit → turn on

3.9 Activating climate recirculation memory

Encoding
Block 08 → Long coding → Byte 4 → bit 5 activate.

3.10 Auto recirculation of the stove after turning off the ignition

Encoding
Block 08 → coding-long coding → 04 Byte → the value "00" is replaced by "10"

26
3.11 Memorization customization recirculation stoves after shutdown
ignition

Encoding
Block 08 → coding-long coding → 04 Byte • bit 4 • enable ( Remembering recirculation setting when terminal 15 is turned off)

3.12 Setting the climate operation: switching off recirculation

Adaptations
Block 08 → [LN] _Blower_logic_manual_adjustment:
[VN] _manual_offset - fully manual climate
[VN] _Blower stage, absolute - with this coding, recirculation is turned on at R and when splashing on the windshield, as well as the semi-automatic fan
speed mode is active, the speed depends on the engine temperature.

3.13 Reducing fogging of windows outside in high humidity

Adaptations
Block 08 → [LN] _Reduction of windowmisting outside at high humidity • ??

3.14 Extending the heating time of the rear window

Features of the
The entered value is measured in seconds, for example 1200/60 = 20 (minutes)

Encoding
Block 09 → login-password 31347 → adaptation →
(03) -Window heater → enter the desired value → save or

Block 09 → login-password 31347 → adaptation → [VN]

_Window Heating Adaptation:
[LO] _Heckscheibenheizung Zeitwert: 600 [UN] _s

3.15 Extending the heating time of the windshield

Features of the
The entered value is measured in seconds, for example 1200/60 = 20 (minutes). To change the heated windshield temperature and heating time
Encoding
Block 09 → login-password 31347 → adaptation → [VN]
_Window Heating Adaptation:
[LO] _Heckscheibenheizung Zeitwert: ___ [UN] _s
[LO] _Abschalttemperatur fuer Heckscheibenheizung: ____ [UN] _ ° C

3.16 Tilting the right mirror when reversing

Encoding
Block 52 → coding-long coding → 04 Byte → 2 bit and 3 bit → turn on
(if mirrors / seats without memory, turn on only [LO] _mirror_lowering_with_rear_gear) 2 bits (if mirrors /
seats with memory, turn on [LO] _position_memory_with_rear_gear) 3 bits
Block 09 → adaptation → Login 31347 ->
IDE08542-ENG116650 - Access Control 2 - Spiegelabsenkung bei Rueckwaertsfahrt → activate → save IDE08542-ENG116657 -
Access Control 2 - Menuesteuerung Spigelabsenkung → activate → to keep
Notes (edit)
After that, you go into the CAR (on-board computer in the radio) -Overview-Mirrors-remove the daw from the synchronous adjustment of the mirrors and put the daw on
the lowering of the rear mirror. After that you need to do a reset to the "Factory settings" ... Hard-reset - CAR + SETUP

27
3.17 Switching on the illumination of the mirrors when driving in reverse

Features of the
Illumination of thresholds from mirrors when reverse gear is engaged. It is nice to see, when maneuvering backwards, that you have under the front wheels, well, and you cannot
touch the car. When the reverse gear is turned on in the dark, the threshold lights in the mirrors light up, slightly highlighting the space on the sides.

Encoding
Block 09 → Safe Access - 31347-Adaptation → Aussenlicht_uebergreifend → Umfeldleuchte als Manoevrierleuchte →
There was no act. - We put— Act. Block 6C → Long coding-Manoeuvre_Light → set the value Incl.

Notes (edit)
This is on Tiguan-2017 with a 360 * all-round view. In theory, then in the octa there should also be a 360 * view. Only works in the dark.

3.18 Folding / unfolding the side mirrors by holding the key button for closing the doors
or when the ignition is turned on

Features of the
There are 2 meanings:
• by convenience operation… - folding mirrors by holding the button -, by look command… -
• folding mirrors when arming -.

Encoding
Block 09 → login-password 31347 → adaptation →
(22) -Access control 2-Funk Spiegelanklappung Modus → by convenience operation ... → activate → save (22) -Access control
2-Funk Spiegelanklappung → NO activate → to keep
or
Block 09 → login-password 31347 20103
[VO] _Spiegelverstellung:
[LO] _Funk Spiegelanklappung Modus: [VO] _by look command via remote control - folding the mirrors by holding down [LO]
_Funk Spiegelanklappen: NO active - folding when the ignition is turned on

3.19 Operation of power windows with the ignition off

Feature
Change Activ to Not Activ - the lifts will be active after the ignition is turned off
When the ignition is off, the power windows continue to work, the door is opened and closed, the power windows are turned off.

Encoding
Block 09 → login-password 31347 → adaptation →
(13) -Acces control 2-Freigabenachlauf FH bei Tueroeffnen abbrechen → activate → to keep

3.20 Closing windows in rain

Features of the
Attention! The encoding is only accepted in ODIS or VCDS 14 and higher.
The wiper switch must be in the rain (auto or drip) position.

Encoding
Block 09 → login-password 31347 → adaptation →
(14) -Access control 2-RegenschlieRen → choose → permanently → save (26) -Access control 2-Menuesteuerung Regenschliessen → activate →
save Block 09 → coding → select (subblock) rain sensor (RLFS: rain and light sensor) → long coding → 00 Byte → 1 bit 2 bit → turn on

or
Block 09 → coding → select (subblock) rain sensor, RLS unit (5Q0 955 559) → long coding →
• Byte 0 → 2 bit → turn on
• Byte 1 • Bit 3, bit 7 • enable
Access Control 2:
Regenschliessen_ein_aus: active

28
Regenschliessen_art: "Permanent", was Once
Menuesteuerung Regenschliessen: "active"
Notes (edit)
We immediately enter the encoding for all bytes, it will not accept it one by one.
06885D: coding for RLFS Skoda sensor Or 07C85D - to turn on the headlights after 140km / h (motorway light)
We get the encoding 07805D

Block 09 → closed area, code 31347 → adaptation, select channels:

• (15) -Access control 2-Regenschliessen_ein_aus, value "active" IDE08542-ENG125655-Access Control 2-
Regenschliessen_ein_aus

• (16) -Access control 2-Regenschliessen_art, value "Permanent" IDE08542-ENG125656-Access Control 2-Regenschliessen_art

• (28) -Access control 2-Menuesteuerung Regenschliessen, value "active" IDE08542-ENG122186-Access Control 2-
Menuesteuerung Regenschliessen

Block 09 → coding → select (subblock) rain sensor, RLS unit → long coding → byte 0 →
activate bits 0,1,2 ( I did not accept the encoding without activating the 0th bit, at the same time we will see if the activation of the light on over 140 km / h also turned out) at the exit, we get the
encoding 07805D, save the encoding and exit.
or
if you have a block 5Q0 955 559 then after adaptations we go to the encoding and from the blocks we select the one with the RLS record
6. long coding; 7. byte 0, activate bits 0,1,2 8. get the encoding 07805D; If you have a 5Q0955547A with two eyes, then most likely it will
not work
Another variant
Block 09 → login-password 31347 → adaptation →
(14) -Access control 2-RegenschlieRen → choose → permanently → to keep ( 14) -Zugangskontrolle 2-
Regenschlieben or (14) or Access Control 2-Rain Close
(26) -Access control 2-Menuesteuerung Regenschliessen → activate → to keep ( 26) -Zugangskontrolle 2-
Menuesteuerung Regenschliessen or Access Control 2-MENU Control Rain Close

Block 09 → coding → select (subblock) rain sensor (RLFS: rain and light sensor) → long coding → 00 Byte → 1 bit
2 bit → turn on
Notes (edit)
open the windows, close the car and pour water on the windshield

3.21 Highway mode

Description
the dipped beam will automatically turn on when the speed is over 140 km / h
Encoding
Block 09 → coding → select (subblock) rain sensor, RLS unit (5Q0 955 559) → long coding → Byte 0 • Bit 0 • enable

3.22 Menu "Service position"

Feature
It's about the service position of the wipers. Works for Swing only. If the service position is turned on with the wiper switch, then it will not work on the Swing.

09 block -> Login 31347 -> Adaptations -> Windshield wiper -> Activate the Menuesteuerung Frontwischer channel.

3.23 Service position of the wipers

Features of the
The function is relevant if there is a heated windshield.
Service position: by default 166.505329 degrees, change it down. Alternative position 2: position of
the wipers with the ignition off.

Encoding
Block 09 → login-password 31347 → adaptation →
Service position → enter the desired value → save save (I have a name in Russian), the default value is 166.505329, I put
90.505329.
Note
There is also an upper stop — as I understand it, this is the final position of the wipers — the default is 166.505329 degrees

29
3.24 Wiping drips with front wipers

Feature
works in motion at a speed of more than 5 km / h and at temperatures above +6
Encoding
Block 09 → Coding → subblock RLFS / RLS → Coding → prescribe 065DFD (was 065DDD)

3.25 Wiping drips with the rear wiper

Feature
if available

Encoding
Block 09 -> Rear → adaptation → [ VO] _Front_wiper: → [ LO] _Traenenwischen Front Status: active

3.26 Adapting the working interval of the rear wiper

Feature
The standard value of 7 seconds is too low, the wiper moves too often and wipes the glass while it is still dry.
Encoding
Block 09 → adaptation → rear wiper:
• Einzelansteuerung Heckintervallwischen → old value - "not active", new -
"Unabhaengig_der_Fahrzeuggeschwindigkeit"
• Einzelansteuerung Heckintervallwischen Zeitintervall 1 → old value - "8s", new - "15s" Komofortwischen
• Heck Intervallpausenzeit Stufe Automatik → old value - "7s", new - "15s" Komofortwischen Heck
• Intervallpausenzeit Stufe Intervall → old value - "7s", new - "15s"

3.27 Automatic activation of the rear wiper

Features of the
Automatic activation of the rear wiper during continuous continuous operation of the front wiper

Encoding
Block 09 → Closed area - code 31347 → Adaptation → IDE02711-ENG116690-Rear WindowWiper-Automatisches Heckwischen →
active
Notes (edit)
Feels like the wiper starts to work when the rain sensor turns the front wipers into continuous mode. The actuation occurs, depending on the number of actuations of the front
wiper, about once every couple of minutes. Most likely, it will work without a rain sensor when you manually turn on the continuous modes of the front wiper.

3.28 Increasing the interval between the operation of the headlight washers

Features of the
The value of the value is measured in seconds.

Encoding
Block 09 → login-password 31347 → adaptation →
• (1) -Windshield wiper-Anzahl - [LO] _Anzahl Betaetigungen Frontwaschanlage pro SRA Aktivierung → enter "15"
→ to keep We put the desired number (for example 1- works every time; 15- will work every 15 times; by default it was -9)
• (2) -Windshield wiper-SRA Verzoegerungszeit → we enter "2000" → to keep ( those. headlamp washer works after 2.0
sec of continuous holding of the washer stalk)

• (3) -Windshield wiper - SRA Waschzeit → we enter "1500" → to keep ( how many seconds will the headlamp washers work -
who needs to change the standard value of 600 ms to, say, 1500 ms (1.5 seconds), I kept the standard for myself)

thirty
3.29 Complete deactivation of headlamp washers

Features of the
The value of the value is measured in milliseconds.
SRA Verzoegerungszeit - duration of holding the washer lever (2000 ms) Nachwaschzeit -
first wash cycle (initially costs 1100 ms). Washzeit - second wash cycle (initially costs
600ms).
Encoding
Block 09 → login-password 31347 → adaptation → Windshield wiper - [LO] _SRA Nachwaschzeit • 0
Windshield wiper - [LO] _SRA Washzeit • 0

3.30 Locking the doors when accelerating to 15 km / h and opening them when
removing the key from the lock

Encoding
Closing
Block 09-Central Electronics → Coding-07 → Long coding → Byte 0 → Bit 4 Block 09-Central electronics → Coding-07
Opening
→ Long coding → Byte 0 → Bit 3

3.31 Convenient door closing

Description
Pribluda from Passat SS - Lowering the glass when closing

Encoding
Block 42 → Long coding → Byte 3 → was 20 we put 22 → preserve driver's door
Block 52 → Long coding → Byte 3 → was 20 we put 22 → preserve passenger door

3.32 Activating the operation of the key fob with the engine running

Encoding
Block 09 → login-password 31347 → adaptation →
(1) -Access control-Funk bei Klemme 15 ein → activate → to keep

3.33 Activation of door sensors when the engine is running

Features of the
in the presence of the Kessy keyless entry system, in addition to paragraph 3.28
Encoding
Block B7 - Long coding - Byte 0, bit 4 - activate.

3.34 Sound accompaniment of opening / closing with a standard key

Encoding
Block 09 → login-password 31347 → adaptation → Find (*) - Acknowledgment signals- ... → 1 channel
- YES, channel 2 - YES, channel 8 - Activ, channel 7 - Activ, channel 3 - Normal.
• (1) -Acknowledgment signals - Akustische Rueckmeldung entriegeln, value "Active" ( sound when opening)
• (2) -Acknowledgment signals - Akustische Rueckmeldung verriegeln, value "Active" ( sound when closing)
• (3) -Acknowledgment signals - Dauer der Akustischen Rueckmeldung vom Einfachhorn, kurz value ( kurz -
a short signal, it feels like the signal just starts and then breaks off); normal ( normal, slightly longer than short, the sound is the same as in the usual start to the
"bibikalku")
• (7) -Acknowledgment signals —Menuesteuerung akustische Rueckmeldung, value "Active" ( submenu in Swing in
section "unlocking / locking ...")

31
 • (8) -Acknowledgment signals - Akustische Rueckmeldung global: value "Active" (9) -Acknowledgment
• signals - Akustische Rueckmeldung Signalhorn, value "Active" ( sound)
• Acknowledgment signals-Optical feedback during locking → Decelerate ( may be required)
• Acknowledgment signals-Optische Rueckmeldung Komfortschliessen → active ( may be required)
• Acknowledgment signals-Optische Rueckmeldung 3.Bremsleuchte → not active ( may be required)
Notes (edit)
After encoding, enable manually in Swing, the last three channels were not touched. Elegance is
activated in the bolero menu.

3.35 Turning on light / sound signaling

Description
when opening (burglary) after arming (active after 1 min)
Encoding
Block 09 → Code 31347-Kodir-Dl. Kodir → Byte 12 → Bit 0 → Active ( flashing turn signals)
Block 09 → Code 31347-Adaptation → Securiti System-Akustischer Alarm Signalhorn channel → Active ( signals to staff
horn)

3.36 Activation of opening the electric door from the salon / from the key

Description
Make ODIS Service. For some reason, under ODIS-Engineering 6.2.2 does not work out
Encoding
Block 6D → login-password 12345 →
• [VN] _Activation with rear lid remote release switch: ( Switching on with the remote switch. otp. cover bug. Compartment)
[LN] _tap_function_temporary_closing: [VN] _active ( Touch function when closing: asset)
• [VN] _Activation with release button for rea r lid lock in ignition key: ( Switching on the lid with the ignition key.
Compartment) [ LN] _tap_function_temporary_closing: [VN] _active ( Touch function when closing: asset)

3.37 Locking the tailgate

Encoding
Block 09 → login-password 31347 → adaptation →
(16) -Access control-ZV Heck nur direkt auswerfen → activate → to keep
Notes (edit)
locks the trunk, opens only from the inside, mechanically !!! No pressing of any buttons helps.
Description
Delay for locking the trunk lid when opening from the remote control. When the car is closed and the opening occurs with a button from the standard remote control. When closed,
the trunk is not locked immediately, but after 27 seconds. Saves when you forget the keys in the trunk
Encoding
Block 09 → login-password 31347 → adaptation →
(26) -Access control-Freigabenachlauf Heck nach Einzeloeffnung ueber HDF-Funktaster → change to active

3.38 Activating MKE

Description
MKE - Fatigue Recognition System.
Fatigue detection is based on an analysis of the driver's actions on the steering wheel. When the system recognizes that the driver is beginning to fall asleep, it beeps and also
displays a text message on the display in the instrument cluster, urging the driver to stop and take at least a short rest. The function is available at speeds above 65 km / h. The
system takes about 15 minutes from the moment the vehicle starts driving to collect sufficient "statistics" of the driver's behavior, on the basis of which it will be able to recognize
the onset of fatigue during the further trip. In addition to the nature of the influences on the steering, data on the road situation (speed, pressing the accelerator pedal, direction
indicator, time of day, duration of the trip, etc.) are also taken into account, as well as the use by the driver of the controls of various systems (air conditioning, telephone, etc.). These
data are transmitted via the CAN bus to the gateway and analyzed there.

Encoding
Block 19 → closed area 16 → enter the code 20103 →
• byte 6 (it was 57, set it to 64).
• byte 11 (it was 00 we put 08)

32
 • byte 12 (it was 00 we put 08) Block 5F → adaptation →
weariness recognition channel:
• 178k - menu display weariness recognition over threshold high - Active 176k - menu
• display weariness recognition - Active ( not activated by default)
• 65k - weariness recognition 0 * 22 - Active ( not activated by default)
Notes (edit)
adaptation for Bolero, a menu appears in the settings. Most likely will not work for Swing.

33
4. OTHER FUNCTIONS

4.1 Shooter test

Feature
The function is not very useful, but nice

Encoding
Block 17 → login-password 20103 → coding-long coding → 01 Byte → bit 0 → turn on

4.2 Deactivating the sound message about the ignition on when the door is opened

Features of the
There are 3 meanings:
- No display (tbd),
- Driver door,
- All doors.

Encoding
Block 17 → login-password 20103 → adaptation → Ignition active message; trigger → select "No display (tbd)" → to keep

or
Block 17 → login-password 20103 → adaptation → [VN] _Ignition_Active_Message → [LN] _Ignition_Active_Message → [VN]
_trigger_on_dc_door
c Octavia A7 1.6 manual transmission 2017 helped the following

Block 17 → access code 25327 → adaptation → Igniter message: inserted → choose ( off, driver's door, all doors) off
→ execute.

4.3 Displaying the battery status in the on-board computer

Turn off the ignition - press and hold the "Set" button on the tidy until the inscription appears
1. Press the button / trip trip odometer (0.0 / SET button) and hold
2. Release the button when the status indicators display the battery
3. Battery indicator is displayed

4.4 Start-up screen of the radio + car image

Features of the
Changing the Swing / Bolero start screen (vRS, SCOUT, Laurin & Klement, GreenLine options). Changing the
view of the car display in the "Car status" menu.
Encoding
Block 5F → login-password 20103 → coding-long coding →
1.18 Byte ( animation when turned on) → value - 01 ( vrs) , 02 ( scout) , 03 ( Laurin & Klement) , 04 ( GreenLine)
(or Bit 0 (vRS), Bit 1 (Scout), Bit 2 (Greenline) and secret L&K Bit 0 and 1 together)
2.2 Byte ( vehicle modification) → 01, 02 - stock machine (1 liftback, 2 combi) , 51, 52 - RS (51 liftback, 52 combi) , 42 - Scout
Or
3.Byte 1 - Bits 0 ~ 23
- 035201, model: Skoda Rapid
- 035203, model: Skoda Rapid Spaceback
- 036200, Model: Skoda Fabia
- 036202, model: Skoda Fabia Combi
- 037301, model: Skoda Octavia liftback
- 038401, model: Skoda Superb liftback
Note
After saving the encoding, you need to apply the new value by rebooting the radio (on Swing - by holding the power button for a long time).

34
4.5 Changing the skin of the radio and tidy

Features of the
Attention! There is a possibility that VCDS 12 encodes this option incorrectly!
Possibly will only work on Bolero (Parktronic, Vehicle condition)
Encoding
Block 5F → login-password 20103 → coding-long coding → 17 Byte → replace with "02" - Change the start menu of the
device.
Block 17 → adaptation → Displaydarstellung → Variante 2 - Change skin tidy
or
Block 17 → coding → 07 long coding → Byte 9 → Bit 0-2 → select 02 Start Screen: Version 3 - Change the start menu of the device

or
Block 5F → login-password 20103 → execute → adaptation 10 → [LO]
_byte_17_Skinning: [VO] _Skin_2 change to [VO] _Skin_3

4.6 Driving School Mode

Features of the
Only on Bolero, 5F channels 11, 171 need to be activated
This modeʼ allows you to display the current speed on the display of the radio. Readings are displayed only when turned on on the radio itself.

Encoding
Block 5F → login-password 20103 → execute → adaptation 10 →
Select the list of vehicle functions can driving school - channel (11) Adjust the value available

Channel (171) - Car Operation Menu - Select menu_display_driving_school Set the value to on
Channel (173) - Car Operation Menu - Select menu_display_driving_school_over_threshold_high Install
value in driving school mode enabled
Note
It turned out, there is little use from him.

4.7 Deactivating the AM band

Features of the
For GU Swing / Bolero

Encoding
Block 5F → login-password 20103 → coding-long coding → 14 Byte → bit 01 → turn on ( was "00" became "02")

4.8 Activating Skoda surround + virtual subwoofer

Features of the
for Swing / Bolero, two settings are added to the setup menu → SKODA Surround and Virtual Subwoofer ..

Encoding
[LO] _byte_11_Sound_System: [VO] _Sound_System_internal
Or
Block 5F → Encoding - Long encoding → byte 11 → in Swing / Bolero without Arkamys package the value is 01 - put 00
(there will be an error) or 04 ( added items Skoda Surround and Virtual Subwoofer) → execute ( alternatively replace Bit 01 with Bit 04)
Notes (edit)
After coding, you must turn off the ignition. The bass has become denser, the treble has been added at the same positions of the equalizer sliders. Arkamys audio package does not work
without filling in special parameters.

35
4.9 Developer mode + sound improvement

Feature
Activation of Engineering Menu (Engineering Testmode) on PG Swing 2 + Input gain change for sound tuning Done by ODIS Engineering.

Coding
Diagnostic session • Developer mode • Perform Block 5F • Adaptation • developer mode • active For Swing:
Long hold SETUP •…. audio management • Input gain For Bolero: Long hold MENU • Green engineering menu •
audio management • Input gain In order not to fly off FM, change in adaptations: [VN]
_Audio_Management_Input_Gain_Offset_Gen2: Change -128 to -120 (respectively, Input Gain level will become
8 and not will be reset). Or

- We launch the ODIS-E program

- Choosing a project (SK25X1) → start
- Selecting block 5F → Diagnostic session ( Diagnostics session) in the window
- that opens, select:
- Development mode → Execute ( execute) Next: Adaptation / parameter → Developer mode ( developer mode) → enter the value
- Activated
Adjusting sound parameters in the Engineering menu
The engineering menu is launched by holding the Setup button for a long time until the menu: Engineering Testmode appears on the screen. Choose: Software System → Audio Management → in the
"Loudness" item we check that there is a tick, then select: Input Gain Offset and in the points below we increase the level by 6-13 dB (as you like)

- FM source - + xx
- Media File Player - + xx BT
- audio - + xx
- AUX in - + xx
We exit the Engineering menu and adjust the balance and equalizer in the sound settings, if necessary.
Notes (edit)
After completing all the sound settings, it is advisable to deactivate the Engineering menu, because it is believed that in the activated state it does not allow some units to "fall
asleep" and this discharges the battery.
Screenshot - hold down the right knob until the signal.

4.10 Improving the sound of the built-in radio

Features of the
The 11 byte encoding is essentially a trifle, it allows you to open the Surround and Subwoofer menus in the new GU (Swing2, Bolero Mib2). For each GU, the value is selected
differently. If the error is in block 11, then the wrong one is selected.
A more radical change in sound is tuning in frequencies and increasing the incoming tone.

Encoding
For Swing2 Block 5F → login-password 20103 → coding-long coding → 11 Byte → replace with "04"
For Bolero Block 5F -> Coding (COD) -> [LO] _byte_11_Sound_System -> [VO] _Sound_System_no_Allocation
We do it in OE or VCP - when enabled. ignition, but not started the internal combustion engine.

1. We do for all pcs. MIB of radio tape recorders on MQB:

Block 5F → login-password 20103 → execute → adaptation 10 →
• channel "(1) -Electrical test of loudspeakers-Mode" - set to "manual" , in the stock "automatic".
Next, we edit all the other paired channels of all speakers:

• channel (2) -Electrical test of loudspeakers-Parameter_AC-Diagnostics_Channel_1_Test_Frequency → 20,000, in stock "19000"

• channel (3) -Electrical test of loudspeakers-Parameter_AC-Diagnostics_Channel_1_Test_Volume → 85 ", in stock "22" (Columbus) or
"48" (Bolero)
• etc. further below all the channels, up to "... _Channel_16_ ...".
Further

• channel (1) -Check tone frequency-High note frequency range → 10000, in the stock "4000 Hz" (COlumbus, Bolero) or "3000" (Swing).
• channel (2) -Check tone frequency-Medium note frequency range → 4000, in stock "1000 Hz" (COlumbus, Bolero) or "1000" (Swing).
• channel (3) -Check tone frequency-Low note frequency range → 400, in stock "100 Hz" (COlumbus, Bolero) or "100" (Swing).
Further

• Audio management input gain-TV Tuner channel → "-1", in stock "-128 dB"
• Audio management input gain-Radio (FM) channel → "-1", in stock "-128 dB"
• Audio management input gain-Radio (AM) channel → "-1", in stock "-128 dB"
• Audio management input gain-Digital radio (DAB) channel → "-1", in stock "-128 dB"
• channel Audio management input gain-Satellite radio " → "-1", in stock "-128 dB"
Further

• channel "Base volume of speech output" → 70 , in stock "50"%. On some radio tape recorders - this channel is not, then we just skip this item.

36
2. Change the encoding:
For Swing: 5F-07-LC-Byte 11-remove bit 0 and set bit 4 or put in HEX: 04. In stock - 01 (incl. - Sound_System_Internal) ...
For Bolero: 5F-07-LC-Byte 11-set bit 0 and set bit 2 or set in HEX: 05. In stock - 01 (incl. - Sound_System_Internal).
Other options:
00 - sometimes: swing, in set style set 01 - factory
default
02 - canton
04 and 05 - bolero and seat FR. The difference between setting 05 and 04 is that 05 has more bass.

For Golf 7 / Columbus / Discover Pro:

5F-07-LC-Byte 11-do not change anything, leave it in stock in HEX: 01.
For Canton:
5F-47-07-LC-Byte 0 - put in HEX: 23. In the stock - "03".
Or, change "byte_0_brand_sound" - set "Fender". In the drain - "default". After
activation, the sound becomes more bass.
Turn on sound from USB / SD. We go with the button to "Sound", to "Sound settings", below "Additional CANTON settings", below we see the active setting "CANTON Surround", check and change the depth
of the volume with the fader to the maximum, moving the fader all the way to the right. Surround sound will be available for both radio and other sources. Volume fader setting - available only from external
sources and is not active in radio mode.

3. Change the settings in GEM:

We turn on the engineering menu of the radio (GEM).

In VCP: 5F, we transfer the diagnostic mode to engineering.

5F-10 - "Developer mode" channel - set "activated". In stock - "not activated".
At Odis Engineering: On the right in the action window - in the root tab "Diagnostic function", select the item "009 - Diagnostic Session", in the window that opens, select "Developer mode".

5F-10 - "Developer mode" channel - set "activated". In stock - "not activated".

We hold the MENU key for a long time. First there will be the first inf. mode available to everyone, in which additional. tabs. Then, after another 15 seconds, while holding,
another mode will open.
Change in GEM:
- for Columbus - do not touch anything;
- for Swing 2, Bolero 1/2, Amundsen rule GEM:
GEM -> main -> audmng ->: set the active item "config_table_persist"
further, go to the "input_gain" sub-item and set all sliders to "7".
Notes (edit)
After coding, you must turn off the ignition.

4.11 Activating the rear speakers

Features of the
For GU Swing

Encoding
Block 5F → login-password 20103 → 04 Byte → enable all bits [LO]
_byte_4_Channel_1_HT: [VN] _installed
[LO] _byte_4_Channel_1_TT: [VN] _installed
[LO] _byte_4_Channel_2_HT: [VN] _installed
[LO] _byte_4_Channel_2_TT: [VN] _installed
[LO] _byte_4_Channel_3_HT: [VN] _installed
[LO] _byte_4_Channel_3_TT: [VN] _installed
[LO] _byte_4_Channel_4_HT: [VN] _installed
[LO] _byte_4_Channel_4_TT: [VN] _installed
Notes (edit)
An error will come out (you need to bring the wires from the radio to the rear speakers and connect
Feature
Rear door speaker activation after self-retrofitting in Swing / Bolero / Amundsen

Encoding
Block 5F → login-password 20103 → Coding 07 → Byte 4 → Bit 6 - Activate. Feider appears in the Swing menu - adjustment
front-back. (4 bytes - turn on the fader, encode 4 Bytes, activate channels 1 through 4)
or
Block 5F → Coding → Long coding → Byte 4 → bits 0 ~ 31 → choose
- BE000000 ( 4 channels / 6 passive speakers)
- FF000000 ( 4 channels / 8 passive speakers) - If the rear doors are equipped with 2-component speakers with tweeters, select accordingly

37
4.12 Activating the low-frequency analogue input AUX-IN

Encoding
Block 5F → Coding → Long coding → byte 8 → bit 4 → turn on

4.13 Activate USB input

Encoding
Block 5F → Coding → Long coding → byte 19 → bits 6 ~ 7 → choose the value 80 ( USB
functionality) or choose the value С0 ( USB and iPhone functionality)

4.14 Activating the rear view camera

Encoding
Block 5F → Long coding → Byte 19 → bit 4 → activate.

4.15 "Green Drive" display

Feature
The entertaining function helps to drive more economically. You can read tips for saving.
Coding
Block 5F → closed area16 → enter the code 20103. → adaptation 10 →
Car_Function_Adaptations_Gen2-menu_display_user_eco_rating put the value active.
For ODIS:

[LO] _menu_display_user_eco_rating: activated

[LO] _menu_display_user_eco_rating_over_threshold_high: activated

4.16 Off Road Display

Feature
This setting will only work on MIB II, you need to have Navigation (don't try if there is no Navigation).
Coding
Block 5F → login-password 20103 → execute → adaptation 10 →
ENG122227-ENG117566-Car_Function_Adaptations_Gen2-menu_display_compass → activated
ENG122227-ENG117568-Car_Function_Adaptations_Gen2-menu_display_compass_over_threshold_high → activated
ENG122229-ENG117732-Car_Function_List_BAP_Gen2-compass_0x15 → activated

4.17 Activating TMC

Feature
TMC - Traffic Message Channel is a technology that is used to transmit information about traffic jams and adverse road conditions. Support for TMC functions allows the
car's navigation system to obtain information about areas with traffic incidents and to build an alternative route to avoid problem areas.

Coding
Block 5F → Coding 07 → Byte 13 → Bit 3 → turn on
Block 5F → login-password 20103 → execute → adaptation 10 →
IDE05111- Paid Traffic Message Service (TMC) →

Device Variants

TMC OFF 65535

SUNA Traffic Telematic 1024
0
VW TMCPro MIB1 3

38
VW TMCPro MIB2 32768/32785 RU
Online Traffic + VW TMCPro 32771

4.18 Adapting microphone sensitivity

Coding
5F • Adaptations • [VN] _Microphone sensitivity • [LN] _sensitivity: default is 0 , you can set from -10 to 10, the value
in decibels. We put 10 and voila, even a whisper can be heard

4.19 120km / h warning

Encoding
Block 17 → login-password 20103 → coding-long coding → 00 Byte → bit 06 → turn on

4.20 Time format - 12h or 24h

Encoding
Block 17 → login-password 20103 → coding-long coding → 01 Byte → bit 07 → turn off

4.21 Setting the maintenance interval

Feature
It is recommended to first reset the intervals by pressing the "0.0 / SET" button on the tidy (how to do this, read the manual for octavia - page 37)
Encoding
Everything is done in block 17, in Adaptations:
Installation of inspection service:
• Setting the mileage before the inspection service - Fix: Max. distance until next mileage-related inspection
• Setting the mileage after the inspection service - FIX: Distance covered since last mileage-dependent inspection
• Setting the time elapsed after the inspection service (in days) - FIX: Time since last time-dependent inspection
Oil change service installation:
• - Setting the mileage before oil change service - SIA: maximum value of distance to service
• - Setting the mileage after oil change service - SIE: distance driven from inspection
• - Setting the time elapsed after the oil change service (in days) - SIE: time from inspection
Or
Block 17 adaptation → SIE: maximum Value of time to service → enter the desired value → to keep
Note
After changing these adaptations, it was possible to achieve the values I needed (because I do not want to change the oil every 15,000 km, but earlier), which are shown in the
Bolero, in the Tech. service.

4.22 Speed limit signs

Feature
Enabling the display of speed limit signs based on map data, only for GU Columbus

Coding
Block 5F → Coding 07 → Byte 24 → Bit 6 → turn on

4.23 Lap timer

Encoding
Block 17 → login-password 20103 → coding-long coding → 01 Byte → bit 03 → turn on

39
4.24 Free space in the tank

Features of the
In general, the function is so-so due to the large error. But it seems like there is a possibility of calibration.
Encoding
Block 17 • Long coding • Byte 10 • Bit 4 • enable ( if there are no 4 bits, In the binary code, the fourth character is 1)
Increasing the adaptation value lowered the Mpg data displayed on the MFA. So, If you want to lower the average MPG displayed on the dash, try increasing the adaptation
value to 102% -> 105%. If you wanted to Increase the Mpg on the display, lower the Adaptation value to 95% -> 98%.
Correction (5 liters more) of free space in the tank.
Block 17 • Long coding • Byte 2 • put 06 You can painlessly choose option 2 and 3

Byte encoding [ LN] _tank_variant:

By default there are:
[VN] _variant_1 - station wagon, 4x4 (5E0920871B)
[VN] _variant_3 - sedan (liftback) (5E0920861B) [VN]
_variant_2 - sedan (5E0920750B)
[VN] _variant _... - sedan (5E0920761В)
For tidy 5E0920761B put [VN] _variant_7
And as an option to understand the curve (you need a password to change the values, do not change)
[VN] _Fuel_tank_sender_calibration_offset_values:
[LN] _Offset_G1: - 12.8 [UN] _l
[LN] _Offset_G2: 12.7 [UN] _l
[LN] _Offset_G3: 12.7 [UN] _l
[LN] _Offset_G4: 12.7 [UN] _l
[LN] _tank_full_calibration: - 12.8 [UN] _l

4.25 Installing the Multifunction

Features of the
ODIS-S coding

Encoding
19 block (Gateway): encoding • in the Installation list • [LO] _Sollverbau_MFL: [VN] _installed - if this value is not
install, there will be an error in block 19, unidentified equipment was found.

5F (infotainment) • adaptation •
• [VN] _Car_Function_List_CAN:
• [LO] _MFL: [VN] _Available
• [LO] _MFL_msg_bus: [VN] _CAN_Infotaiment
• [VN] _Car_Function_Adaptations:
• [LO] _menu_display_MFL_jocker: [VN] _activated
• [LO] _menu_display_MFL_jocker_over_threshold_high: [VN] _activated [VN]
• _Car_Function_List_BAP:
• [LO] _MFL_Jocker_msg_bus_0x34: [VN] _CAN_Infotaiment
• [LO] _MFL_Jocker_0x34: [VN] _activated
It is necessary to take into account which paddle switches are installed: with buttons on the on-board computer or without buttons on the on-board computer.

• If there are no onboard buttons, then Buttons for multi-function display: not installed
• If there are onboard computer buttons, then Buttons for multi-function display: installed
If the coding is incorrect, there will be an error in the 16th block for an open circuit.

40
RESPECTS

Many thanks and wishes of health to the unknown authors of these finds, since I
collected encodings from scattered files on the network, as well as to other so far
unknown pioneers.

If you have not indicated anyone, do not be angry, but just let us know about yourself and a
mention of you will appear in this file!

Also, materials from the following resources were most likely used:

Car Lovers Club

DRIVE2.RU

Skoda Club Belarus

Octavia club

SanchoPanso998 Knowledge Library

VAG Blog

autoprogs.ru

POSITIONING ON THIRD PARTY RESOURCES IS PERMITTED ONLY

WITH AN INDICATION OF THE ORIGINAL SOURCE - COMMUNITY
"VAG CODES" on DRIVE2.RU

QUESTIONS AND ADDITIONS MAY SEND

SUNLIONN

41